E-municipalities - Eservices To Citizens And Tender Results

LED Lamps- bulb ( PAC Only ) Average Turn Over of Last 3 Years 10 Lakh (s) Experience with Gov. Required 3 Year (s) LED Lamps- Bulb ( 366 ) ( Under PAC ) Make havells Model ledlamp45wattthreaded Technical Specifications * As per GeM Category Specification Specification Specification Name Values Allowed Values GENERIC LED LAMP Power Ratings/LED Lamp Luminous Flux 18Watt/1800 Lumens 18Watt/1800 Lumens Colour Temperature (K) 6500 2700, 4000, 5700, 6500 Type of Lamp CAP B22d B22d, E27 Warranty for free replacement (Years) 2 Years 2 Years, 3 Years Conformity to Indian Standard IS:16102 part I and Part II latest * FUNCTIONAL LAMP Efficacy (Lm/W) >/=100 * LED Chip Efficacy (Lm/W) >/=130 * 1/4 Colour Rendering Index(CRI) >/=80 * Beam Angle (Degree) >/=120 * Power Factor >/=0.9 * Total Harmonics (%) =15 * Driver Efficiency (%) >/=85 * LED chip Wattage (Watt) =1 * Surge Voltage withstand (KV) 2.5 * Operating Voltage range (Volts) 100 Volt to 300 Volt * Rated Voltage for Performance and life (Volts) 220 Volt to 240 Volt * Lumen maintenance @ 25 deg after 6000 hours (%) >/=80 * CONSTRUCTIONAL Light Source (as per LM80 orIS16106) SMD LED chip * LED Make Havells * Light Source (as per LM80/IS16106) SMD LED Chip * Lamp Shell material Polycarbonate * Ingress Protection in IP >/=20 * TEST REPORT AND CERTIFICATIONS LED life Certificate for 25000 hrs as per LM80 Yes * LED life test Certificate No. - * LED life Certificate Test Report Date - * LED lamp life certificate for 6000 hrs Yes * LED Lamp certificate Number - * LED Lamp Life Certificate date - * EMC Test Yes * Availability of test Report to IS:16102 Part I and IS:16102 Part II latest Yes * Test certificate No. - * Test Report Date - * 2/4 Name of lab where test conducted - * Complusory Registration(CRS) of BIS for safety as per IS 16102-I Yes * * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Vikas Chauhan 206122, Tilak Nagar, Auraiya/?????, Uttar Pradesh/????? ?????? 366 30

LED Lamps- bulb ( PAC Only ) Experience with Gov. Required 3 Year (s) LED Lamps- Bulb ( 500 ) ( Under PAC ) Make havells Model havells Technical Specifications * As per GeM Category Specification Specification Specification Name Values Allowed Values GENERIC LED LAMP Power Ratings/LED Lamp Luminous Flux 12Watt/1200 Lumens 12Watt/1200 Lumens Colour Temperature (K) 6500 2700, 4000, 5700, 6500 Type of Lamp CAP B22d B22d, E27 Warranty for free replacement (Years) 3 Years 2 Years, 3 Years Conformity to Indian Standard IS:16102 part I and Part II latest * FUNCTIONAL LAMP Efficacy (Lm/W) >/=100 * LED Chip Efficacy (Lm/W) >/=130 * Colour Rendering >/=80 * 1/4 Index(CRI) Beam Angle (Degree) >/=120 * Power Factor >/=0.9 * Total Harmonics (%) =15 * Driver Efficiency (%) >/=85 * LED chip Wattage (Watt) =1 * Surge Voltage withstand (KV) 2.5 * Operating Voltage range (Volts) 100 Volt to 300 Volt * Rated Voltage for Performance and life (Volts) 220 Volt to 240 Volt * Lumen maintenance @ 25 deg after 6000 hours (%) >/=80 * CONSTRUCTIONAL Light Source (as per LM80 orIS16106) lm80 * LED Make havells * Light Source (as per LM80/IS16106) SMD LED Chip * Lamp Shell material Polycarbonate * Ingress Protection in IP >/=20 * TEST REPORT AND CERTIFICATIONS LED life Certificate for 25000 hrs as per LM80 Yes * LED life test Certificate No. - * LED life Certificate Test Report Date - * LED lamp life certificate for 6000 hrs Yes * LED Lamp certificate Number - * LED Lamp Life Certificate date - * EMC Test Yes * Availability of test Report to IS:16102 Part I and IS:16102 Part II latest Yes * Test certificate No. - * Test Report Date - * Name of lab where test - * 2/4 conducted Complusory Registration(CRS) of BIS for safety as per IS 16102-I Yes * * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Vikas Chauhan 206122, Tilak Nagar, Auraiya/?????, Uttar Pradesh/????? ?????? 500 30

waste containers or rigid liners- Dust bin or Garbage Bin or Household Bin Waste Containers Or Rigid Liners- Dust Bin Or Garbage Bin Or Household Bin ( 10000 ) Technical Specifications * As per GeM Category Specification Specification Specification Name Values Allowed Values GENERIC Utility Domestic Domestic ISI Marked No No CM/L No (If ISI Marked Yes) (If No write NA) NA * Class confirming to IS:12402 (For Public Dustbins) NA * Material HDPE HDPE CAPACITY Bin Capacity (Volume) (Ltrs) 10 Litres 10 Litres DIMENSIONS Wheel Dimension in (mm) (Diameter x Thickness ) (mm x mm) NA * Weight of Dustbin (Complete unit) (Grams) 350 * 1/3 CONSTRUCTIONAL Colour green * Wheel Lock Without * Load carrying Capacity (Kgs) 7 * Wall Non- Perforated * Lid Swing type * Handle Without * Wheel Without * Wheel Material NA * Towage Provision no * Gripping Provision NA * Plugged outlet for washing & draining Without * UV Resistant no * Dust Bin stand without * No. of Compartments in the Bin single * CERTIFICATIONS Availability of Test Reports from Central Government/NABL/IL AC acredited Lab to prove conformity to the specifications yes * Test report number 12460 * Test report date 02/08/2018 * Name and address of lab INDIA LAB, DELHI * * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Maheshwari Sharan 284202, NAGAR PALIKA PARISHAD-GURSARAI-JHANSI 10000 15

waste containers or rigid liners- Dust bin or Garbage Bin or Household Bin Waste Containers Or Rigid Liners- Dust Bin Or Garbage Bin Or Household Bin ( 15 ) Technical Specifications * As per GeM Category Specification Specification Specification Name Values Allowed Values GENERIC Utility Public (Mobile containers confirming IS: 12402) Public (Mobile containers confirming IS: 12402) ISI Marked No yes, No CM/L No (If ISI Marked Yes) (If No write NA) NA * Class confirming to IS:12402 (For Public Dustbins) Type A (Two fixed wheels, trolley type) * Material HDPE HDPE CAPACITY Bin Capacity (Volume) (Ltrs) 120 Litres (as per IS: 12402 Pt1 and 2 120 Litres (as per IS: 12402 Pt1 and 2 DIMENSIONS Wheel Dimension in (mm) (Diameter x Thickness ) (mm x mm) NA * Weight of Dustbin (Complete unit) 2500 * 1/3 (Grams) CONSTRUCTIONAL Colour green * Wheel Lock With * Load carrying Capacity (Kgs) 120 * Wall Non- Perforated * Lid without lid * Handle Without * Wheel Without * Wheel Material NA * Towage Provision yes * Gripping Provision Both Frontal &Ventral * Plugged outlet for washing & draining Without * UV Resistant yes * Dust Bin stand with * No. of Compartments in the Bin single * CERTIFICATIONS Availability of Test Reports from Central Government/NABL/IL AC acredited Lab to prove conformity to the specifications yes * Test report number BR26A0040355 * Test report date 18-11-2017 * Name and address of lab Patliputa Industrial Area Patna * * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Maheshwari Sharan 284202, NAGAR PALIKA PARISHAD-GURSARAI-JHANSI 15 30

tricycle or rickshaw Tricycle Or Rickshaw ( 12 ) Technical Specifications * As per GeM Category Specification Specification Specification Name Values Allowed Values Generic Parameters Driving Mechanism Pedestal Chain Pedestal Chain Length of Tricycle (mm) 1150 Any applicable numeric value Length of Cart (mm) 1500 1500 Width of Cart (mm) 1000 1000 Height of Cart (mm) 300 300 Number of Plastic Containers with lid and handle (Nos) 8 8 Capacity of the each Container (Litres) 22.5 22.5 Material of the Container and Lid Virgin HDPE Virgin HDPE, Virgin Polypropylene Material of Handle of container - * Loading Capacity of the Tricycle (Kg) - * 1/5 Certification Parameters Manufacturer Drawing No. - * Constructional Parameters Frame Structure Made of MS Tubes Made of MS Tubes Diameter of MS Tube (mm) 25 Any applicable numeric value Thickness of MS Tube (mm) 8 Any applicable numeric value Cart Frame Material MS Angle of size 25 x 25 x 3 mm MS Angle of size 25 x 25 x 3 mm Material of Bottom Plate of Cart Mild steel plate Mild steel plate Thickness of Bottom Plate of Cart (mm) 3 Any applicable numeric value Holes in Bottom Plate of Cart Having 12 mm diameter holes at a distance of 200 mm square Matrix * Lengthwise Number of Stiffeners below the Plateform to support the MS Plate (Nos) 3 * Widthwise Number of Stiffeners below the Plateform to support the MS Plate (Nos) 1 * Stiffener Material M S Angle of size 25 x 25 x 3 mm M S Angle of size 25 x 25 x 3 mm Finish of Handle Nickel and Chrome Plated * Finish of Chain Wheel Nickel and Chrome Plated * Finish of Crank Nickel and Chrome Plated * Front Rim Thickness (mm) 12 * Number of Front Wheel (Nos) 1 * Type of Front Wheel Tyre Tube Wheel Puncherless Rubberised Wheel, Tyre Tube Wheel Front Rim Diameter (mm) 38 * Front Rim Width (mm) 700 * Number of Spikes in Rear Wheel (Nos) 18 * Diameter of Spike of 700 Any applicable numeric 2/5 Front Wheel (mm) value Number of Rear Wheels (Nos) 2 2 Type of Rear Wheels Puncherless Rubberised Wheel Puncherless Rubberised Wheel Rear Rim Diameter (mm) 700 Any applicable numeric value Rear Rim Width (mm) 38 Any applicable numeric value Rear Rim Thickness (mm) 700 * Number of Spikes in Front Wheel (Nos) 136 * Thickness of Spike of Rear Wheel (mm) 1.25 Any applicable numeric value Daimeter/Width of Spike in Rear Wheel (mm) 25 * Support Details of Rear Wheels - * Minimum Wall thickness of the Plastic Container and Lid (mm) 1.28 Any applicable numeric value Maximum Ash content of the container and Lid when tested as per Annex D of IS 14887/2014 (%) 1 Any applicable numeric value Pretreatment Two coats of red oxide after phsphating before painting Two coats of red oxide after phsphating before painting Colour of the Frame - * Paint Ennameled Paint Powder Coating, Ennameled Paint Colour of the Cart - * Manufacturer 's Name Marked on the Tricycle Yes * Year of Manufacturing Marked on the Tricycle Yes * Finish of Rim Nickel and Chrome Plated * Colour of the Container and Lid - * Accessories Parameters Bell Yes * 3/5 Two Reflectors at back Yes * Type of Reflector Adhesive Tape * Lock for locking the Tricycle Yes * Tool Kit Yes * First Aid Box Yes * Tricycle Seat with Cover Yes * Hangers for broom and wiper Yes * * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Maheshwari Sharan 284202, NAGAR PALIKA PARISHAD-GURSARAI-JHANSI 12 30

hopper or tipper Hopper Or Tipper ( 4 ) Technical Specifications * As per GeM Category Specification Specification Specification Name Values Allowed Values Generic Parameters Type of TIPPER Box body Tipper Box body Tipper Type of TIPPER if other tipper, please declare type of Tipper, * Main Engine Capacity (cc) 702 * Make of Chassis - * Type of Chassis Frame - * Category of Vehicle for which Chassis to be used Light Capacity Commercial Vehicles Light Capacity Commercial Vehicles, Medium Capacity Commercial Vehicles, Heavy Capacity Commercial Vehicles Type of Chasssis Chassis with Facecowl * Type of Fuel Diesel Diesel, CNG Vehicle Emission Complaince bs iv bs iv, BS-III (only for Defence) 1/6 Fuel Consumption ( declared by OEM as certified by Test Agency under Rule 115of CMVR 1989) (Ltr/Hr) 21.5 Any applicable numeric value Speed, Max (Km/Hr) 60 * Max Engine Power BHP (BHP@rpm) 16 Any applicable numeric value Max Engine Torque (N-M@rpm) 39 Any applicable numeric value Main Engine Aspiration Natural Aspiration Natural Aspiration, Turbocharged, Supercharged, Turbocharged+ Supercharged, Turbocharged Intercooled No. of Cylinder in Main Engine (Nos) 2 Any applicable numeric value Fuel Tank Capacity (Ltrs) 30 Any applicable numeric value Gradeability of Vehicle with load( %) 16.38 * Gradeability of Vehicle without load ( %) 18 * Ground Clearance (mm) 175 Any applicable numeric value Wheel Base (mm) 2100 * Kerb Weight (Kg) 840 Any applicable numeric value Gross Vehicle Weight (Kg) 1700 Any applicable numeric value No of Axle (Nos) 2 * Axle Configuration ( Number of Outside Tyre x Number of Driving Tyre) - * Type of Front Axle and Suspension System - * Type of Rear Axle and Suspension System - * Type of BIS MARKED Vehicle Tyre Radial * Chassis Transmission System Manual Automatic, Manual Number of Speed 4 * 2/6 Forward Gears Type of Steering Manual Manual, Power Operated Turning Radius, Min (mm) 4300 Any applicable numeric value Speed Governers No * ABS Fitted No * Front Vehicle Brake - * Rear Vehicle Brake - * Type of Clutch - * Tipping Angle (Degree) 45 45-9999999 Tipper Container cap acity/Volume(cubic metres) 2.5 0.5-10.5 Certification Chassis Certification ARAI/VRDE/ICAT No. - * Performance Parameters Standard Sparewheel and Tool Kit Yes * Warranty Time (Month) 12 * No. Of Free Service (Nos) 3 * Battery Warranty (Months) 12 * Warranty Distance (Km)(Unlimited during warranty Period) Yes Yes Consructional Parameters Length of Chassis (mm) 3800 * Width of Chassis (mm) 1500 * Height of Chassis (mm) 1845 * Size Of Front Tyres (mm) - * Size Of Rear Tyres (mm) - * Size of Wheel (mm) 145 Any applicable numeric value Tipper body Pivot length (mm) 2240 * Tipper body Length (mm) 2240 * Tipper Body Height (mm) 735 * Overall Height of Tipper 1518 * 3/6 from Ground (mm) Body Plate Thickness (mm) 1.6 1.5-9999999 Main Frame Thickness (mm) 3 Any applicable numeric value Pneumatic System false * Hydarulic System true * Tipping Hydraulic Cylinders(Make) - * Hydraulic System Driven by Power Pack Unit * Auxiliary Diesel Engine for Hydraulic and Pneumatic Operation false * If Yes Auxiliary Diesel Power (HP@rpm) 0 Any applicable numeric value Auxiliary Diesel Engine Transmission - * Auxiliary Diesel Engine fuel tank Capacity (Ltrs) 0 Any applicable numeric value No. of Cylinders in Auxiliary Diesel Engine 0 * Tipper Container Material Mild Steel Mild Steel, Stainless Steel, Aluminium, Chromium Alloy Based Thickness of sheet from tipper Collector Container Made (mm) 1.6 Any applicable numeric value Dumping Height (mm) 1012 Any applicable numeric value Engine Oil Pressure Level Indicator in Control Panel true * Fuel Gauge Indicator in Control Panel true * Engine Cooling Liquid Temperature Indicator in Control Panel false * Operating Hour Meter false * Locking/Unlocking of Tipper Discharge Container Yes * Lowering/Lifting of Tipper Discharge Yes * 4/6 Container Counter Weight false * If yes Counter Weight (kg) 0 * Paint Automotive Paint * * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Maheshwari Sharan 284202, NAGAR PALIKA PARISHAD-GURSARAI-JHANSI 4 90

automotive vehicles pneumatic tyres Average Turn Over of Last 3 Years 1 Lakh (s) Experience with Gov. Required 1 Year (s) Automotive Vehicles Pneumatic Tyres ( 10 ) Technical Specifications * As per GeM Category Specification Specification Specification Name Values Allowed Values Ungrouped Category Of Pneumatic tyres Special use Tyre: mixed used Normal Road Tyre, Special use Tyre: mixed used, Restricted speed: snow tyre Tyres With Tube With Tube Conformity to Indian Standrad for Pneumatic Tyres IS:15636 latest for Automotive vehicles: Pneumatic tyre for commercial Vehicles- Diagonal and radial ply IS:15627 latest for Automotive vehicles: Pneumatic tyre for two and three wheeled motor Vehicles, IS:15633 latest for Automotive vehicles: Pneumatic tyre for passenger car Vehicles- Diagonal and radial ply, IS:15636 latest for Automotive vehicles: Pneumatic tyre for commercial Vehicles- 1/4 Diagonal and radial ply Conformity to Indian Standrad for Pneumatic Tubes IS:13098 latest for Automotive vehicles: Tubes for Pneumatic tyre IS:13098 latest for Automotive vehicles: Tubes for Pneumatic tyre, NA for Tubeless TYRES ISI MARKED (for Tyres) Yes Yes CM/L No and validity date)(for Tyres - * ISI MARKED (for Tubes) Yes Yes, NA for Tubeless and without tube CM/L No and validity date(for tubes) - * Type of tube Class-A * Manufactures name and Trade Name - * Tyre-size Designations 16.9X28 * Tube-size Designations 16.9X28 * Structure of Tyre Reinforced or Extra Load Diagonal or bias ply, Bias-belted, Radial, Reinforced or Extra Load Ply Rating 12 * Speed Category - * Load indicas - * Side Well (mm) 410 * Inner area of Tyers (mm) 270 * Section Width (min)(mm) 414 * Overall Width (max)(mm) 1410 * Section Height (mm) 100 * Nominal Aspect Ratio(mm) 100 * Outer diameter (min)(mm) 1410 Any applicable numeric value Nominal Rim Diameter(mm) 28 Any applicable numeric value Maximum load Rating(%) 82.67 Any applicable numeric value Conformity to AIS-044 Yes * Availability of Type Test Report covering YES * 2/4 complete test parameters as per relevant BIS spcification latest for Tyre type, from any ILAC/NABL accredited/Central Gov. LAB. Test cetificate No. - * Test Report Date - * Name and address of the Lab where test Conducted - * Others Certificate ie ROHS, WHO, GMP etc - * Warranty Time 1 1, 2, 3 * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Manoj Kumar Gupta 244001, TOWNHALL NAGAR NIGAM MORADABAD, UTTAR PRADESH 10 15

automotive vehicles pneumatic tyres, automotive vehicles pneumatic tyres Average Turn Over of Last 3 Years 1 Lakh (s) Experience with Gov. Required 1 Year (s) Automotive Vehicles Pneumatic Tyres ( 18 ) Technical Specifications * As per GeM Category Specification Specification Specification Name Values Allowed Values Ungrouped Category Of Pneumatic tyres Special use Tyre: mixed used Normal Road Tyre, Special use Tyre: mixed used, Restricted speed: snow tyre Tyres With Tube With Tube, Tubeless, Without Tube Conformity to Indian Standrad for Pneumatic Tyres IS:15636 latest for Automotive vehicles: Pneumatic tyre for commercial Vehicles- Diagonal and radial ply IS:15627 latest for Automotive vehicles: Pneumatic tyre for two and three wheeled motor Vehicles, IS:15633 latest for Automotive vehicles: Pneumatic tyre for passenger car Vehicles- Diagonal and radial ply, IS:15636 latest for 1/8 Automotive vehicles: Pneumatic tyre for commercial Vehicles- Diagonal and radial ply Conformity to Indian Standrad for Pneumatic Tubes IS:13098 latest for Automotive vehicles: Tubes for Pneumatic tyre IS:13098 latest for Automotive vehicles: Tubes for Pneumatic tyre, NA for Tubeless TYRES ISI MARKED (for Tyres) Yes Yes CM/L No and validity date)(for Tyres - * ISI MARKED (for Tubes) Yes Yes, NA for Tubeless and without tube CM/L No and validity date(for tubes) - * Type of tube Class-A * Manufactures name and Trade Name - * Tyre-size Designations 7.50/16 * Tube-size Designations 7.50/16 * Structure of Tyre Reinforced or Extra Load Diagonal or bias ply, Bias-belted, Radial, Reinforced or Extra Load Ply Rating 16 * Speed Category - * Load indicas - * Side Well (mm) 212 * Inner area of Tyers (mm) 212 * Section Width (min)(mm) 212 * Overall Width (max)(mm) 825 * Section Height (mm) 825 * Nominal Aspect Ratio(mm) 6 * Outer diameter (min)(mm) 825 Any applicable numeric value Nominal Rim Diameter(mm) 20 20.0 Maximum load Rating(%) 7.75 7.75, 3725 2/8 Conformity to AIS-044 Yes * Availability of Type Test Report covering complete test parameters as per relevant BIS spcification latest for Tyre type, from any ILAC/NABL accredited/Central Gov. LAB. YES * Test cetificate No. - * Test Report Date - * Name and address of the Lab where test Conducted - * Others Certificate ie ROHS, WHO, GMP etc - * Warranty Time 1 1, 2, 3 * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Manoj Kumar Gupta 244001, TOWNHALL NAGAR NIGAM MORADABAD, UTTAR PRADESH 18 15 Automotive Vehicles Pneumatic Tyres ( 6 ) Technical Specifications * As per GeM Category Specification Specification Specification Name Values Allowed Values Ungrouped Category Of Pneumatic tyres Special use Tyre: mixed used Normal Road Tyre, Without Tube Conformity to Indian Standrad for Pneumatic Tyres IS:15627 latest for Automotive vehicles: Pneumatic tyre for two and three wheeled motor Vehicles IS:15627 latest for Automotive vehicles: Pneumatic tyre for two and three wheeled motor Vehicles, IS:15633 latest for 3/8 Automotive vehicles: Pneumatic tyre for passenger car Vehicles- Diagonal and radial ply, IS:15636 latest for Automotive vehicles: Pneumatic tyre for commercial Vehicles- Diagonal and radial ply Conformity to Indian Standrad for Pneumatic Tubes IS:13098 latest for Automotive vehicles: Tubes for Pneumatic tyre IS:13098 latest for Automotive vehicles: Tubes for Pneumatic tyre ISI MARKED (for Tyres) Yes Yes CM/L No and validity date)(for Tyres - * ISI MARKED (for Tubes) Yes Yes, NA for Tubeless and without tube CM/L No and validity date(for tubes) - * Type of tube Class-A * Manufactures name and Trade Name - * Tyre-size Designations 9.00-16 * Tube-size Designations 9.00-16 * Structure of Tyre Reinforced or Extra Load Diagonal or bias ply, Reinforced or Extra Load Ply Rating 18 * Speed Category - * Load indicas - * Side Well (mm) 12 * Inner area of Tyers (mm) 12 * Section Width (min)(mm) 9 * Overall Width (max)(mm) 15 * Section Height (mm) 38 * Nominal Aspect Ratio(mm) 11 * Outer diameter (min)(mm) 900 900.0 Nominal Rim 16 Any applicable numeric 4/8 Diameter(mm) value Maximum load Rating(%) 96 Any applicable numeric value Conformity to AIS-044 Yes * Availability of Type Test Report covering complete test parameters as per relevant BIS spcification latest for Tyre type, 3 * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Kamal Kumar Saxena 244001, UTTAR PRADESH 6 15 Automotive Vehicles Pneumatic Tyres ( 12 ) Technical Specifications * As per GeM Category Specification Specification Specification Name Values Allowed Values Ungrouped Category Of Pneumatic tyres Normal Road Tyre Normal Road Tyre, Restricted speed: snow tyre Tyres With Tube With Tube Conformity to Indian Standrad for Pneumatic Tyres IS:15636 latest for Automotive vehicles: Pneumatic tyre for IS:15627 latest for Automotive vehicles: Pneumatic tyre for two 5/8 commercial Vehicles- Diagonal and radial ply and three wheeled motor Vehicles, IS:15636 latest for Automotive vehicles: Pneumatic tyre for commercial Vehicles- Diagonal and radial ply Conformity to Indian Standrad for Pneumatic Tubes IS:13098 latest for Automotive vehicles: Tubes for Pneumatic tyre IS:13098 latest for Automotive vehicles: Tubes for Pneumatic tyre, NA for Tubeless and without tube CM/L No and validity date(for tubes) - * Type of tube Class-A * Manufactures name and Trade Name - * Tyre-size Designations 1000x20 * Tube-size Designations 1000x20 * Structure of Tyre Bias-belted Diagonal or bias ply, Reinforced or Extra Load Ply Rating 16 * Speed Category - * Load indicas - * Side Well (mm) 325 * Inner area of Tyers (mm) 22.5 * Section Width (min)(mm) 312 * Overall Width (max)(mm) 12 * Section Height (mm) 312 * Nominal Aspect Ratio(mm) 20 * 6/8 Outer diameter (min)(mm) 1135 Any applicable numeric value Nominal Rim Diameter(mm) 8.5 Any applicable numeric value Maximum load Rating(%) 3725 Any applicable numeric value Conformity to AIS-044 Yes * Availability of Type Test Report covering complete test parameters as per relevant BIS spcification latest for Tyre type, UTTAR PRADESH 12 15

LED Luminaire (For Road and Street Lights) LED Luminaire (For Road And Street Lights) ( 800 ) Technical Specifications * As per GeM Category Specification Specification Specification Name Values Allowed Values STANDARDS LED Luminaire conformity to IS:10322/Part 5/Section 3/2012 latest and IS: 16107 (Part 2/Sec 1):2012 latest Yes * Photo biological safety of LEDs used shall be as per IS:16108/2012 (exempt group) Yes * Types of LED Luminaire as per the IS: 16107(Part-2 Sec.-1)/2012 Type B * Types of LED Modules as per the IS:IS: 16103(Part-2)/2012 Type 3 * LED Rating (in Watts)/System Wattage/Rated Power 45W 45W 1/7 Luminaire System Efficacy (Lumen/watt) >/= 100 Lm/Watt * Ingress Protection (IP Rating) as per IS:10322 (Part 1):1982 latest IP66 * Warranty for free replacement (in years) 5 2, 3, 4, 5 ELECTRICAL EFFICIENCY Input operating Voltage range and frequency 140 to 270 V olts AC at 50 Hz+/-2 with auto cutt off at below 120V * Automatic Higher Cut off voltage above 300 volt Yes * Rated voltage 230 V AC 50 Hz * AC Power Factor at full load ≥ 0.95 * Driver Efficiency (in %age) Upto 100W: ≥85%, Above 100W: >/=90% Yes * Total Harmonics Distortion ≤ 10 * "The total circuit power shall not be more than 110 percent of the value declared by the manufacturer (as per Cl. 8 of IS:16104:2012 lates)" Yes * OPTICAL LED chip Efficacy ≥130 Lm/Watt * Colour temperature 6000+/-500K * Working life for LED (Minimum 50, 000 burning hours as per LM-80 and LM 21 reports) Yes * Colour Rendering Index(CRI) ≥70 * LED Beam Angle ≥120 * Optic lense materal (UV stabilised) Poly carbonate lense * THERMAL MANAGEMENT Heat sink should be die- cast aluminium along with sufficient heat sink fins to dissipate heat effectively Yes * Junctiojn/Soldering Yes * 2/7 point temperature shall not exceed 85 deg.c as per LM 80 report Capacitor shall be rated for a temperature of 105 deg. celsius or better Yes * Operating temperature range -10 deg C to +50 deg C -20 deg. C to +50 deg. C, 10 deg C to +50 deg C, 10 deg C to +55 deg C Operating Humidity Range 10 % to 95% RH * PROTECTION Short circuit Protection Yes * Over load protecton Yes * Over Voltage protection Yes * Reverse polarity Yes * High voltage test (1.5 KV for one minute between supply terminals and body of the unit) Yes * Insulation resistance between earth and current carrying part >100 M Ohm * The luminaire shall be protected against surges and transients ( Internal) >/=4KV * The luminaire shall be protected against surges and transients of >/=10KV (External) Yes * CONSTRUCTIONAL The Luminaires casing/housing (single piece housing) shall be pressure die casted aluminium alloy with higher thermal conductivity Yes * The luminaire body must be corrosion resistant powder coated Yes * All fastners must be of stainless steel Yes * Protection of the entire housing (both LED section and driver IP66 * 3/7 section) as per IS:10322 (Part 1):1982 latest Extruded silicon loop gasket shall be provided in the lantern body to ensure a weather proof seal between the UV Glass cover and the metal housing to exclude the entry of the dust, water, insects etc., Yes * Luminaries light transparency should be of Toughened glass Yes * Toughned transparent glass cover thickness >/=4 mm * Toughned Glass shall not get discoloured shall not suffer degration due to heat and ageing within warranty period Yes * Number of electronic control gear (power supplies) 1 No. 1 No., 2 Nos., 3 Nos., 4 Nos. Light Source SMD LED Chip as per LM 80/IS16106 * Driver components shall be industrial grade or above Yes * PCB shall be FR4 grade minimum 0.8 to 1.0 mm thick or more Yes * The Luminaires works on single phase three wires system (Phase, Neutral and Earth) Yes * Suitable connector shall be provided for LED connection between driver output and LED Yes * Length of ISI marked three core wire (shall be provided along with supply of material) 50 cm 50 cm, 100 cm MARKING "Manufactures Name and and brand on the Engraved/Embossed * 4/7 aluminium die cast body " Manufacturer’s name, model number, serial number Yes * Date of manufacture (month-year), and lot number as identification mark inside each unit and the outside of each packaging box Yes * The operation characteristics voltage and power be marked inside of each LED luminaire unit Yes * Diameter of pole Luminiare suitable for: (upto 45W Pole OD: shall be 40mm), (>45W<120W Pole OD: Shall be 50 mm), (above 120W: OD shall be 60 mm for which luminiare is suitable Yes * REPORTS AND CERTIFICATIONS LED Make OSRAM/NICHIA/CREE SAMSUNG/SEOUL LUMILEDS/PHILIPS SYSKA/LUMENMAX EVERLIGHT/EDISON BRIDGELUX NATIONSTAR/REFOND * System must have EMI/EMC compliance as applicable (Test reports shall be furnish to the buyer/consignee on demand) Yes * LM 79 (Photometry) (Ref.IS:16106:2012) report from Central Government Lab NABL/ILAC accrediated lab. Reports shall be furnish to the buyer consignee on demand (LM-79 report shall have total lumen output, power, PF, Current in Amps, CRI & CCT etc., ) Yes * LM 80 & TM 21 (Ref. Yes * 5/7 IS:16105:2012) Report and Photo biological report for LED report from Central Government Lab NABL/ILAC accrediated lab. Reports shall be furnish to the buyer consignee on demand (LM-80 report shall have the Pohoto Biological report of the LED Chip being used in the luminaire) Availability of test Report from Central Government Lab NABL/ILAC accrediated lab to Indian Standrad IS:10322/part 5/sec-3/2012 and IS 16107 (Part 2/Sec 1) : 2012 Yes * Seller shall furnish the Type test reports to the buyer/consignee on demand Yes * DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes * LED Luminaire for road and street lighting shall comply with Complusory Registration(CRS) of BIS for safety as per IS 10322 (Part 5/Section 3): 2012 as applicable on date Yes * * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Ajit Kumar Rai 202001, SEWA BHAWAN, NAGAR NIGAM ALIGARH, NEAR GHANTA GHAR, 202001 800 15

Cattle Catcher Vehicle

LED Luminaire (For Road and Street Lights) ( PAC Only ) Average Turn Over of Last 3 Years 25 Lakh (s) Experience with Gov. Required 3 Year (s) LED Luminaire (For Road And Street Lights) ( 150 ) ( Under PAC ) Make halonix Model halonix60wledstreetlight Technical Specifications * As per GeM Category Specification Specification Specification Name Values Allowed Values STANDARDS LED Luminaire conformity to IS:10322/Part 5/Section 3/2012 latest and IS: 16107 (Part 2/Sec 1):2012 latest Yes * Photo biological safety of LEDs used shall be as per IS:16108/2012 (exempt group) Yes * Types of LED Luminaire as per the IS: 16107(Part-2 Type B * 1/7 Sec.-1)/2012 Types of LED Modules as per the IS:IS: 16103(Part-2)/2012 Type 3 * LED Rating (in Watts)/System Wattage/Rated Power 60W 60W Luminaire System Efficacy (Lumen/watt) >/= 100 Lm/Watt * Ingress Protection (IP Rating) as per IS:10322 (Part 1):1982 latest IP66 * Warranty for free replacement (in years) 2 2, 3, 4, 5 ELECTRICAL EFFICIENCY Input operating Voltage range and frequency 90 to 300 Volts AC at 50 Hz+/-2 * Automatic Higher Cut off voltage above 300 volt Yes * Rated voltage 230 V AC 50 Hz * AC Power Factor at full load ≥ 0.95 * Driver Efficiency (in %age) Upto 100W: ≥85%, Above 100W: >/=90% Yes * Total Harmonics Distortion ≤ 10 * "The total circuit power shall not be more than 110 percent of the value declared by the manufacturer (as per Cl. 8 of IS:16104:2012 lates)" Yes * OPTICAL LED chip Efficacy ≥130 Lm/Watt * Colour temperature 6000+/-500K * Working life for LED (Minimum 50, 000 burning hours as per LM-80 and LM 21 reports) Yes * Colour Rendering Index(CRI) ≥70 * LED Beam Angle ≥120 * Optic lense materal (UV Poly carbonate lense * 2/7 stabilised) THERMAL MANAGEMENT Heat sink should be die- cast aluminium along with sufficient heat sink fins to dissipate heat effectively Yes * Junctiojn/Soldering point temperature shall not exceed 85 deg.c as per LM 80 report Yes * Capacitor shall be rated for a temperature of 105 deg. celsius or better Yes * Operating temperature range -10 deg C to +55 deg C -20 deg. C to +50 deg. C, 10 deg C to +50 deg C, 10 deg C to +55 deg C Operating Humidity Range 10 % to 95% RH * PROTECTION Short circuit Protection Yes * Over load protecton Yes * Over Voltage protection Yes * Reverse polarity Yes * High voltage test (1.5 KV for one minute between supply terminals and body of the unit) Yes * Insulation resistance between earth and current carrying part >100 M Ohm * The luminaire shall be protected against surges and transients ( Internal) >/=4KV * The luminaire shall be protected against surges and transients of >/=10KV (External) No * CONSTRUCTIONAL The Luminaires casing/housing (single piece housing) shall be pressure die casted aluminium alloy with higher thermal conductivity Yes * The luminaire body must be corrosion Yes * 3/7 resistant powder coated All fastners must be of stainless steel Yes * Protection of the entire housing (both LED section and driver section) as per IS:10322 (Part 1):1982 latest IP66 * Extruded silicon loop gasket shall be provided in the lantern body to ensure a weather proof seal between the UV Glass cover and the metal housing to exclude the entry of the dust, water, insects etc., Yes * Luminaries light transparency should be of Toughened glass Yes * Toughned transparent glass cover thickness >/=4 mm * Toughned Glass shall not get discoloured shall not suffer degration due to heat and ageing within warranty period Yes * Number of electronic control gear (power supplies) 1 No. 1 No., 2 Nos., 3 Nos., 4 Nos. Light Source SMD LED Chip as per LM 80/IS16106 * Driver components shall be industrial grade or above Yes * PCB shall be FR4 grade minimum 0.8 to 1.0 mm thick or more Yes * The Luminaires works on single phase three wires system (Phase, Neutral and Earth) Yes * Suitable connector shall be provided for LED connection between driver output and LED Yes * 4/7 Length of ISI marked three core wire (shall be provided along with supply of material) 100 cm 50 cm, 100 cm MARKING "Manufactures Name and and brand on the aluminium die cast body " Engraved/Embossed * Manufacturer’s name, model number, serial number Yes * Date of manufacture (month-year), and lot number as identification mark inside each unit and the outside of each packaging box Yes * The operation characteristics voltage and power be marked inside of each LED luminaire unit Yes * Diameter of pole Luminiare suitable for: (upto 45W Pole OD: shall be 40mm), (>45W<120W Pole OD: Shall be 50 mm), (above 120W: OD shall be 60 mm for which luminiare is suitable Yes * REPORTS AND CERTIFICATIONS LED Make OSRAM/NICHIA/CREE SAMSUNG/SEOUL LUMILEDS/PHILIPS SYSKA/LUMENMAX EVERLIGHT/EDISON BRIDGELUX NATIONSTAR/REFOND * System must have EMI/EMC compliance as applicable (Test reports shall be furnish to the buyer/consignee on demand) Yes * LM 79 (Photometry) (Ref.IS:16106:2012) report from Central Government Lab NABL/ILAC accrediated lab. Reports shall be furnish to the buyer Yes * 5/7 consignee on demand (LM-79 report shall have total lumen output, power, PF, Current in Amps, CRI & CCT etc., ) LM 80 & TM 21 (Ref. IS:16105:2012) Report and Photo biological report for LED report from Central Government Lab NABL/ILAC accrediated lab. Reports shall be furnish to the buyer consignee on demand (LM-80 report shall have the Pohoto Biological report of the LED Chip being used in the luminaire) Yes * Availability of test Report from Central Government Lab NABL/ILAC accrediated lab to Indian Standrad IS:10322/part 5/sec-3/2012 and IS 16107 (Part 2/Sec 1) : 2012 Yes * Seller shall furnish the Type test reports to the buyer/consignee on demand Yes * DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes * LED Luminaire for road and street lighting shall comply with Complusory Registration(CRS) of BIS for safety as per IS 10322 (Part 5/Section 3): 2012 as applicable on date Yes * * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 6/7 1 Dinesh Kumar 206243, office nagar Panchyat Bidhuna 150 15