UDL/DSL/EASTERN RLY Tender Results

Spares of coupling flexible pipe 3 inch [Spares of coupling flexible pipe 3 inch to Drg no. 17282238 as per BLW part no 17280825 & EMD part no 8471160, consist of 4 items: 1.Half coupling, Qty/set -04 nos, 2.Ring, Qty/set -02 nos, 3. Bolt, Qty/set - 02 nos, 4. Nyloc nut, Qty/set -02 nos. Note: Material to be procured from BLW approved vendors for PL no- 17280825, EMD Pt no- 8471160, since items are child part of PL- 17280825. ]

LED based Flasher Light Unit without con [LED based Flasher Light Unit without control unit as per EMD part no. 8494495, DLW part no. 17451383, DLW drg. No. 18361432, RDSO Spec. No. ELRS/Spec/LFL/0017, Rev-1, Sept 2004 or latest. Note: Material to be procured from BLW approved vendors only. ]

Washer Flat of Size 7/16 (Copper) to EMD [Washer Flat of Size 7/16 (Copper) to EMD partNo. 116104 and BLW PartNo. 19391080 as per Drawing No. 116104 Rev.Db or Latest. Note: To be procured from a past proven supplier to Indian Railway for the same item only. Test certificate (TC) andguarantee certificate(GC) are also required from ]

LOCKING PLATE FOR K CLASS CTRB AS PER RD [LOCKING PLATE FOR K CLASS CTRB AS PER RDSO APPROVED DRG WD06085/S-2 Note: Material to be procured from RDSO approved vendors only. ]

Bolt HEX (1-1/4) - 12 * (2-3/4) to EMD P [Bolt HEX (1-1/4) - 12 * (2-3/4) to EMD Part No. 8029567 and DLW Part No. 19018010 as per Drawing number 8029567 Rev Ga or latest. Material spec: AISI 8642H STEEL/AISI 4140H STEEL, Heat to 1550%uF0B0 F, Quench in Oil, temper to 28-32, Rockwell ?C?. ]

Shim 3/8 Inch As Per EMD Part No. 400258 [Shim 3/8 Inch As Per EMD Part No. 40025867]

Electronic Control Module suitable for S [Electronic Control Module suitable for SIL vaporid Air Dryer as per SIL Drg. No. 09872401 and WABCO Part No. 63351, for Diesel locomotive]

CLEAT CABLE RUBBER-1X4-7/8 INCHES-3 TO E [CLEAT CABLE RUBBER-1X4-7/8 INCHES-3 TO EMD PT NO. 10649385 & DLW PT NO. 18460630 FOR TM CABLE APPLICATION.]

BALL BEARING 6214 2Z/C3.

CLEAT to Drawing No. 10660947, ALT.DLW P [CLEAT to Drawing No. 10660947, ALT.DLW Pt No.18460690 OF HHP locomotives.]

Set of overhauling kit for fuel pump mot [Set of overhauling kit for fuel pump motor of HHP locos as per EMD part No-40122943 BLW part no.11815565. Each kit should consist of 04 items: 1. Rubber "O" ring (Neoprene rubber) for pump, Qty/Set-01 no. 2. Rubber "O" ring (Neoprene Rubber) Between Motor Body And End Plate, Qty/Set- 02 no.. 3. Feather key for drive gear, Qty/Set - 01 no. 4. Needle Bearing BHA 1110Z, Qty/Set-01 no. ]

Lock Assembly as per BLW Part no. 815853 [Lock Assembly as per BLW Part no. 8158536 Alt-Ta]

Set of items for EPD and HOD connection, [Set of items for EPD and HOD connection, consisting of three items as detailed below: (1) Screw Socket head cap No. 10-24 %u03A4%u03A1%u0399 x 1-1/2 inch and EMD Pt.No.147115 and DLW Pt.No.19150064, Qty/set: 2 Nos, (2) Screw Socket head cap 10-24 TPI x 1/2 inch and EMD Pt. No. 186542 and DLW Pt. No. 19150076, Qty/set: 8 Nos, (3) Screw Socket head cap 5/16 inch-18 TPI x 7/8 inch and EMD Pt. No. 9421623 and DLW Pt. No. 19150167, Qty/set: 2 Nos. Material Test Certificate (MTC) required & traceable on NABL, at the time of material supply. ]

Set of items consisting of four items as [Set of items consisting of four items as detailed: 1. Elbow assembly 5/8 inch HYD includes Viton "O" Ring to EMD Pt. No. 40046718 and BLW Pt. No.17320793 as per Drawing No.40046718 ALT Aa or Latest, Qty/set - 20 nos. 2. Connector assembly 5/8 inch HYD to EMD Pt. No. 40046717 and BLW Pt. No. 17320781 as per Drawing No. 40046717 ALT Aa or Latest. Qty/set - 50 Nos. 3. Elbow assembly 5/8 inch- 45 HYD includes Viton "O" Ring as per EMD Pt. No. 40046719 and BLW Pt. No. 16050101 as per Drawing No. 40046719 ALT Ab or Latest. Qty/set - 60 Nos. 4. TEE 5/8"T X 5/8"T X 1/2"PT to EMD Pt.No. 9403100 and BLW Pt. no. 16240492, as per Drawing No. 9403100 ALT Aa or Latest. Qty/set - 10 Nos. Note: Test certificate (TC) & Guarantee certificate (GC) is required from Supplier. ]

1) Set of item, consist of: 1.Dowel Threade [Set of item, consist of: 1.Dowel Threaded 1-8 X 3-1/4 to EMD part no. 8022474, Qty/set - 01 no, 2.Dowel Threaded 1 x 3-3/4 Inches to EMD Part No. 8341940, Qty/set -01 no. Material spec: 1. SAE 12L14 or SAE 1117 STEEL. 2. SAE 4140H STEEL, Temper Rockwell "C",34-38. 3. GM 286-M-STEEL.] 2) Nut Hex Head Jam 1-8 to DLW Drg. No. 218 [Nut Hex Head Jam 1-8 to DLW Drg. No. 218445 and to DLW Part No. 19354198. Material spec: 1. SAE 12L14 or SAE 1117 STEEL. 2. SAE 4140H STEEL, Temper Rockwell "C", 34-38. 3. GM 286-M-STEEL.]

CLEAT, RUBBER to DLW DRG. No. 10661183 A [CLEAT, RUBBER to DLW DRG. No. 10661183 ALT.a AND TO DLW PART NO.17271800 for WDP4/WDG4 Locos]

Deflector, Water to EMD Part No. 8348964 [Deflector, Water to EMD Part No. 8348964. Material Composition: SAE CA230 Red Brass (UNS Copper Alloy No. C23000) ]

Anti-seize compound (copper and graphite [Anti-seize compound (copper and graphite based) to lubricate and protect threaded connections and flanges at temperatures upto 1800deg. F (980 %uF0B0C) and extreme load pressure conditions. Make/Brands: (i) Molykote 1000 OF DOW CORNING (ii) Loctite LB 8008 C5A Anti Seize (iii)Neveseize C-975 of Anabond or equivalent. Note: 1) Rate shall be quoted per kg only. 2) Firm should furnish tender specific dealership authorization certificate. 3) The product shall have minimum shelf life of 12 months from the date of supply. ]

One set Heavy duty circlip plier consist [One set Heavy duty circlip plier consisting of 12 items. Deatil technical specification as per attached Annexure. Accepted Make/Brand: GEDORE/ STANLEY/ SNAP ON /BLACK/ DECKER or SIMILAR. Note: Tenderer shall submit technical datasheet of the offered material like Brand/Make & Model no.along with their offer, otherwise such offers are liable for rejection.]

Lead Wire to Size: 3.18 mm (1/8 inch) to [Lead Wire to Size: 3.18 mm (1/8 inch) to EMD Part No. 8243661 for HHP Locomotives. Note: Material Test Certificate (MTC) required & traceable on NABL, at the time of material supply. ]

Spacer (For Electrical Cable) to EMD Par [Spacer (For Electrical Cable) to EMD Part No. 8451802 and BLW PL. No. 18460057 for HHP locomotives.]

Set of 03 Items consisting of three item [Set of 03 Items consisting of three items as per details below: Bolt hex head of size 5/8"x11x3-3/4" to EMD Pt No.271569 & DLW Pt No.19016165, Qty/set-1 No, 2.Nut hex lock-nylock 5/8"x11- Nylon to EMD Pt. No. 8032747 & DLW Pt No.19350326,Qty/set- 1 No, 3. Washer Special Damper to EMD Pt No.9532904 & DLW Pt No.19394366, Qty/set-1 No ]

Set of items for lube oil line to cam sh [Set of items for lube oil line to cam shaft bearing as detailed: 1.BOLT. Hex head X INCH-28 TPI x 5/8 INCH-Oll line to rocker arm shaft to EMD PLNG 181311 and BLW PL.No.19010059, Qty/Set-32 Nos. 2. BOLT- Hex head 1/4 INCH - 20 TPI x 3/4 INCH, Oill line to Camshaft Bearing to EMD PLNG 179795 and BLW PL.No.19010011, Qty/set-32 Nos. 3.WASHER 1/4 spring lock washer to EMD PL.No.103319 and BLW PL.No. 19390014, Qty/Set-64 Nos. Material Test Certificate (MTC) required & traceable on NABL, at the time of material supply. ]

Set of item consist of: 1. 2 SN EN 853, [Set of item consist of: 1. 2 SN EN 853, 4785 PSI, 3/8" dia (9.5 mm) High pressure hydraulic hose reinforced with two layers of high tensile steel wire braid in compliance to DIN EN 853 2SN & SAE 100R2AT Spec. 50m. In length. Qty/set-1 nos. 2. 3/8" Male/Female BSPT or NPT water jet nozzles, material: Brass, Operating Pressure: from 4000-5000 PSI, flow Rate: 1 to 100 LPM, Spray Pattern: Full cone/hollow cone, Qty/set-1 nos ]

Coil magnet 1033 (+/-) 5% ohms for 4 poi [Coil magnet 1033 (+/-) 5% ohms for 4 point general purpose relay to EMD part no.9516672. Note: Sample to be approved before bulk supply]

Servo Mesh SP 68. MAKE-SERVOMESH SP-68 O [Servo Mesh SP 68. MAKE- SERVOMESH SP-68 OF IOCL, MAK AMOCAN-68 OF BPCL,PARTHAN EP-68 OF HPCL OR ITS EQUIVALENT]

Digital refractometer for ethylene glycol confirming to RDSO specification - RDSO/2018/ELS/SMI/0325, latest version as per Annexure. Annexure enclosed.

Fully insulated open head electrode hold [Fully insulated open head electrode holder, 600 Amps. Detail technical specification as: (a) suitable for 95 mm core dia. Aluminium cable (b) Holder should have embossed/ Cast, Identification mark of manufacturer of holder. Make: ESAB/ JACKSON/LINCOLN or similar. Special Eligibility Criteria - Only OEM or their Authorized Dealer/Distributor should quote along with "Tender Specific Authorization" from OEM at the time of Tendering, otherwise offer will be ignore. ]

Supply, installation and commissioning [Supply, installation and commissioning for set of spare parts in 200 KVA oil cooled stabiliser, consist of following material: 1. 3 phase, micro controller PCB, Qty/set- 01 no, 2. 3 phase motor driver PCB, Qty/set- 01 no, 3. R - C network, Qty/set- 03 nos, 4. Servo motor AC ,10 kg/cm2, Qty/set- 01 no. ]

Digital Tachohour meter (Model TH-118) R [Digital Tachohour meter (Model TH-118) RPM cum hours meter Cummins part no.2879766. Material to be procure from OEM or OEM authorized vendor. Note : Sample to approved before bulk supply ]

Set of material consist of: 1. EMS 478 [Set of material consist of: 1. EMS 478 Silicon Elastomer Coated Fiberglass Sleeve, Inner Diameter: 18 mm, Outer Diameter: 20 mm, Red in Color, conforming to Thermal Class H. The sleeve shall have a Di-electric Strength of not less than 5 kV/mm thickness and a Working Temperature Range from -60 Degree Celsius to +200 Degree Celsius, Qty-1 met/set. 2. EMS 478 Silicon Elastomer Coated Fiberglass Sleeve, Inner Diameter: 18 mm, Outer Diameter: 20 mm, Blue in Color, conforming to Thermal Class H. The sleeve shall have a Di- electric Strength of not less than 5 kV/mm thickness and a Working Temperature Range from -60 Degree Celsius to +200 Degree Celsius, Qty-1 met/set. 3. EMS 478 Silicon Elastomer Coated Fiberglass Sleeve, Inner Diameter: 18 mm, Outer Diameter: 20 mm, White in Color, conforming to Thermal Class H. The sleeve shall have a Di-electric Strength of not less than 5 kV/mm thickness and a Working Temperature Range from -60 Degree Celsius to +200 Degree Celsius, Qty-1 met/set. Note: 1.The fiber glass should be RoHS and REACH Complaint. 2.Material to be supplied in continuous spool as per mentioned colours. 3.The material should be technically compliant to UL 1441 GRADE A certificate. 4.Offered product to be supplied with material test certificate (MTC) & warrenty test certificate (WTC) traceable to NABL. ]

Set of fasteners consist of following it [Set of fasteners consist of following items: 1. Hex head bolt size 5/16 inch x 18 TPI x 1-3/4, Grade 8 (thread length 1 inch), Qty/set. - 01 no, 2. Nut 5/16 inchx 18 TPI , Qty/set. - 01 no, 3. Spring washer 5/16 inch, thickness 1.5 mm Qty/set. - 01 no, 4. Flat washer ID 5/16 inch, OD 3/4 inch, thickness 1.5 mm, Qty/set. - 02 nos. All the set of material should be lead plated. Note: A test certificate (TC) & Guarantee certificate (GC) is also required from supplier. ]

Ammeter for Battery Charging (75-0-75) f [Ammeter for Battery Charging (75-0-75) for HHP locomotives equivalent to Medha Part No. SP696141011 or EMD Part No. 2295001.]

Hose assembly, detector to water cut off [Hose assembly, detector to water cut off valve to DLW Pt. no. 17320768 and EMD Pt. no. 9320121 EMD Drg.No. 9320121 Rev. Let.A1.]

Procurement of Portable Digital Ultraso [ Procurement of Portable Digital Ultrasonic Flaw Detectors (UFD) with a-scan storage used for ultrasonic Scanning Various Axles and Armature Shafts along with computer facility. Detail technical specification as per attached Annexure. Note: Material to be procured from RDSO approved source only. ]

Heat shrinkable sleeve for used as cabl [Heat shrinkable sleeve for used as cable/70 sq mm cabel cover, consist of : (i) Flexible and durable cable sleeve, size 24/8, material-PET(polyethylene Terephthalate) color- Red, quantity 400m (ii) Flexible and durable cable sleeve, size 24/8, material-PET(polyethylene Terephthalate) color- yellow, quantity 400m (iii) Flexible and durable cable sleeve, size 24/8, material-PET(polyethylene Terephthalate) color- Blue, quantity 400m Above mentioned item consist 400 meter each. Warranty Certificate and Test Certificate should be provided at the time of material supply. ]

BOLT. Hex head 3/8-24 x 4-5/8 to EMD Par [BOLT. Hex head 3/8-24 x 4-5/8 to EMD Part No.188146 D and DLW Part No. 19012238. Material spec: 6M 280M STELL , FINISH : PLAIN ]

BRUSH ASSEMBLY MOVABLE CONTACT FOR ST CO [BRUSH ASSEMBLY MOVABLE CONTACT FOR ST CONTACTOR TO EMD PART NO.9536539. Note: Material to be procured from any past proven source of this material. ]

Set of consumables required for Kent Ult [Set of consumables required for Kent Ultra water purifier, set consist of - 1.Sediment filter suitable to Kent Ultra UV water Purifier, Qty/set : 1 No, 2. Carbon filter suitable to Kent Ultra UV water Purifier , Qty/set : 1 No. ]

3/4 inch square drive pneumatic impact w [3/4 inch square drive pneumatic impact wrench,maximum torque 1200 ft.lbs or more, detailed technical specification as per attached Annexure.]