Loading…
Loading…
6,169 results • Best match
Constructing Eight Suited Guest House in Place of old Condemned Guest House at Hanumakonda, with G+1 building Subwork: Providing Lift Facility in Eight Suited Guest House in Place of old Condemned Guest House at Hanumakonda
Supply and placing of Design Mix Concrete M 20 grade corresponding to IS 456 with minimum cement content of 350 kgs per 1 cum of concrete using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard Granite metal (coarse aggregate) (consisting of nominal size metal 60% of 20mm , 15% of 13.20/12.50mm , 15% of 10mm and 10% of 6mm ) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (with 50% river sand & 50% manufactured sand) coarse aggregate, water etc., to site, centering using Steel scaffolding pipes, jack Props, wallers, Foot plates, brackets, steel Centering Plates, etc., including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing and cost of overheads & contractors profit etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402) FOR LINTELS- Ground Floor
Improvements to Choultry Building of Sri Durga Bhirava Brhmanan Annadana Satram, Bhiravakona(V), CS Puram(M), Prakasam District
(CONSTRUCTION OF FIRST FLOOR ROOMS OVER EXISTING BUILDING OF BRAHMANA ANNADHANA SATHRAM AT SRI TRIMUKA DURGA BHYRAVESWARA SWAMY TEMPLE BHIRAVAKONA,AMBAVARAM(V),CS PURAM(M) PRAKASAM(Dt).)VRCC M20 Nominal mix using 20mm size hard granite m/c graded metal(coarsed aggregate)including cost andconveyance of all materials like cement,fine aggregate(sand),coarse aggregate,water etc., to site with all steel centering,shuttering,machine mixing,laying ,vibrating, lifting,curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work as per SS (A)Columns.
Construction of APARA KARMALA BHAVAN in Div no.04 Under AE-VII Section(11th call)
Supply and placing of the M20 Design Mix Concrete corresponding to IS 456 using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including tremmy pumping,laying concrete,curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work. Bored cast-in-situ under reamed piles includig bore pile stem and under ream bulbs.
Completion of west side Municipal School building in W.N-22
S/F of Mild steel tubular pipe fabrication work
Renovation and replacement of chilled water piping system at Mod Lab C Block, BARC, Trombay 400085
Supply, fabrication, installation and painting of MS structural material such as I-beams, channels, angles, sections, chequred plates, gratings etc. required for supports, platforms, EPs etc. as per site requirement as per clause no. 21 of Tech. Spec
Electrification of new Planetarium at University of Calicut
90.14.1.1 Fabrication, supply, conveyance, installation testing and commissioning of floor or wall mounting, dust and vermin proof, cubicle type MV panel board comprising of the following components/ devices & complying to IS 8623. Fabrication of fully partitioned, dust and vermin proof enclosure for panel assembly as per form 4 of IS 8623 (with latest amendments) using CRCA sheet as per approved design and requirement, with front and rear access facility, bus bar chambers, hinged doors for all switch gear compartments, earthing the doors using 4 sq mm braided copper conductor, providing necessary cut-outs for mounting meters, relays, indication lamps, bus bar interconnection etc, detachable covers for bus bar chamber and cable alley, powder coating the assembly after subjecting to 7 tank process etc as required. CRCA sheet alone be used for the fabrication. Angles/ flats/ slotted angles etc shall not be used for the fabrication of panel assembly. The measurments will be taken the area of the complete sheets used for panel board including partitions, folding, shrouding etc.Supply and fabrication of MV panel board using 2.00mm CRCA sheet, powder coated (excluding base frame)