Plant Protection Input Tenders

26 12.6.2 Supplying of recess mounting non integral type ........ LED w luminaire comprising of pressure decast/extruded aluminium housing, with spring loaded false ceiling clamps, Power LEDs with CCT 6500 degree K, CRI> 70%. efficacy > 100 lumen per watt, 120degree beam spread, life> 25000 burning hours and Compliance to IS 10322/IEC 60598, LM 79 & LM 80. The lamp compartment is enclosed with anti glare opal diffuser which enhances the lighting level LEDs are driven by HF electronic driver integrated in a separate control gear assembly., with PF > 0.95, power loss should 5% of lamp wattage., short circuit & open circuit protection to be integrated in the circuit, THD less than 20%, Life as per LM 79. The operating input voltage should be between 130 to 275 volts. BIS Approved and Tested by NABL/CPRI accredited laboratory with 2 years Warranty against any manufacturing defect working under standard electrical condition. - LED modular down light 2'x2' /1' X 4' 34 -36watt No 20 (https://eproc.karnataka.gov.in/eprocurement/jsf/indent/view_work_indent_work_detailestimate.seam?pageId=view_work_indent_detailestimate&actionMethod=jsf%2Findent%2Fview_work_indent_work_detailestimate.xhtml%3ArateAnalysis.viewRateAnalysis%28+detailEstimate+%29&conversationId=8552&conversationIsLongRunning=true&conversationPropagation=join&dataModelSelection=detailEstimate%3AworkIndentWorkSummarySOREstimatesList%5B25%5D塹ᴻ䡿ⲯ嶂藄挧ꮥ)

25.2:Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including: a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)-cumsmoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including: b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers. c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment , including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass. d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight. e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineerin- Charge. Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this sub-head. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves ) on the external face shall be measured in sqm. up to two decimal places. Note:-2. The following performance test are to be conducted on structural glazing system if area of structural glazing exceeds 2500 Sqm from the certified laboratories accreditated by NABL(National Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies, India. Cost of testing is payable separately. The NIT approving authority will decide the necessity of testing on the basis of cost of the work, cost of the test and importance of the work. Performance Testing of Structural glazing system Tests to be conducted in the NBL Certified laboratories 1. Performance Laboratory Test for Air Leakage Test (-50pa to ? 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr? 2. Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331-09 testing method for a range up to 2000 ml.? 3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01-05 testing method for a range upto 2000 ml? 4. Structural Performance Deflection and deformation by static air pressure test (1.5 times desing wind pressure without any failure) as per ASTME-330-10 testing method for a range upto 50 mm? 5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method for Qualitative test? Tests to be conducted on site 6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000ml?

S.I.T.C of Following rating approved make LED Bollard Fitting with cylindrical shape and inverted cone shape head of height 600 to 850 mm power input -8/9 watt with die cast aluminium housing opel with PC diffuser, IP-65/54 protection, confirming to IS : 10322 part 5 etc all complete as requird. (Excluding Plinth Charge.)

Supply and transportation of 6W LED slim panel Light Round / Square with System Lumens≥510lm, Housing made of Powder coated die cast aluminum housing with extended heat sink, with Protruded plastic Diffuser, IP20, Inbuilt Electrical protections like Over/Under voltage, short circuit, Over load, Open Circuit, Miswiring, LG7 standard applicable, operating voltage range of 150 to 265 Volts AC, P.F ≥ 0.9, Surge protection: 2KV, THD10%, with high power LED's having efficacy of ≥ 100 lumens/watt, CCT: 3000K/4000K/5600K ±300K, CRI≥70. Manufacture has to submit LM79,LM80 & Photobiological Safety Report. Luminaire Performance Complies to IS10322 (Part 5/Sec 3) & IEC 60598- 1,IEC 60529 ISO certified company. LUMINAIRE MAKE : Pharox / Surya / Syska / Muelux / Fortune Art / Capart / Green Lites / Kashyap BLU / R-LED / GM / Million. LED MAKE : PHILIPS LUMILEDS / CREE / NICHIA / OSRAM / SAMSUNG / LG LEDs.

Supply and transportation of 6W LED slim panel Light Round / Square with System Lumens≥510lm, Housing made of Powder coated die cast aluminum housing with extended heat sink, with Protruded plastic Diffuser, IP20, Inbuilt Electrical protections like Over/Under voltage, short circuit, Over load, Open Circuit, Miswiring, LG7 standard applicable, operating voltage range of 150 to 265 Volts AC, P.F ≥ 0.9, Surge protection: 2KV, THD10%, with high power LED's having efficacy of ≥ 100 lumens/watt, CCT: 3000K/4000K/5600K ±300K, CRI≥70. Manufacture has to submit LM79,LM80 & Photobiological Safety Report. Luminaire Performance Complies to IS10322 (Part 5/Sec 3) & IEC 60598- 1,IEC 60529 ISO certified company. LUMINAIRE MAKE : Pharox / Surya / Syska / Muelux / Fortune Art / Capart / Green Lites / Kashyap BLU / R-LED / GM / Million. LED MAKE : PHILIPS LUMILEDS / CREE / NICHIA / OSRAM / SAMSUNG / LG LEDs.

Supply and transportation of 6W LED slim panel Light Round / Square with System Lumens≥510lm, Housing made of Powder coated die cast aluminum housing with extended heat sink, with Protruded plastic Diffuser, IP20, Inbuilt Electrical protections like Over/Under voltage, short circuit, Over load, Open Circuit, Miswiring, LG7 standard applicable, operating voltage range of 150 to 265 Volts AC, P.F ≥ 0.9, Surge protection: 2KV, THD10%, with high power LED's having efficacy of ≥ 100 lumens/watt, CCT: 3000K/4000K/5600K ±300K, CRI≥70. Manufacture has to submit LM79,LM80 & Photobiological Safety Report. Luminaire Performance Complies to IS10322 (Part 5/Sec 3) & IEC 60598- 1,IEC 60529 ISO certified company. LUMINAIRE MAKE : Pharox / Surya / Syska / Muelux / Fortune Art / Capart / Green Lites / Kashyap BLU / R-LED / GM / Million. LED MAKE : PHILIPS LUMILEDS / CREE / NICHIA / OSRAM / SAMSUNG / LG LEDs.