Solar Street Lights Tenders

S&F All-in-One Solar street light 60 watts luminaire output (120 Lumen/Watt) with octagonal GI hot dip galvanised pole of height not less than 5meter and consist of high efficiency LEDs, efficient mono crystalline solar panel confirming to IEC 61215, IEC 61730, IEC 61701 & MNRE certified, new age lithium ferro phosphate battery enclosed in corrosion free IP22 CRCA box with suitable ventilation for fresh air and as per BIS certified and a silicon encapsulated high efficiency MPPT charge controller for high efficiency charge controller to change the batteries intelligent microprocessor algorithms automatic determine sunrise and sunset, along with aluminium housing and in-built PIR motion sensor, with a provision for higher charging efficiency, protection for deep discharge, overcharging etc., fixed with 04Nos of M16x600/EN 8 grade foundation bolt, 1 mtr arm for light fixing & RCC / PCC foundation all as per manufacturer's specifications/ instructions, including dismantling existing u/s street light pole of any type after disconnecting electrical connections and making good the disturbed surface, complete all as specified and directed. Note: The contractor shall submit and approve the foundation drawing issued by the manufacturer before starting the work.

Supply and fix Solar street light fitting of LED 60 watt with 2 days backup IP 65/66 protection on existing pole with complete all as specified and directed. Make: Bajaj, Model: Falcon Plus 60W or its equivalent.

Solar Based Street Light of Following Specification Semi Integrated Solar Street Light 30 W Battery Type Lithium Ion 11.1V 24ah Solar Panel 12V 60W LED Chip Brand Osram Led Life Time Over 5000 hours Charging Time 5 – 6 hours Lumen 3500 – 3700 Lighting Viewing Angle 120° Backup Time 1 – 2 Days

SOLAR STREET LIGHTING SYSTEM: * 30Watt Solar Semi Integrated street light (LED Make:Osram/Philips) * 24AH 12.8V LiFEPO4 Battery with mppt Charge Controller. * 75 Watt solar PV Module. * 1.Supply of 5m height 5 inch dia GI (Average dia tappered from bottom to top) tubular pole and at the bottom one base plate of size 30 x 30 x 5 mm having a through hole of size 14 mm dia at the centre of the ase plate with recuired nut and bolt with pole cap Pole with Light arm and PV Structure. 2.Painting of tubular pole with arms with ant coat of red oxide primer and two coats of aluminium paint and bottom one meter with black paint with supply of paints and labour. 3.Labour charges towards installation of 5 mtr height steel tubular pole including concreting of pole base and couping with supply of concreting materials as per following specification. Planting depth of,1.5 mtr pole pit size 1.2 x 1.2 x 1.8 m concreting- 1:4:8 with 4 cm HG metal size and couping of standard size into 40 cm X 40 cm X 50 cm with cement concreting 1:2:4 uaing 20 mm BHCBG chips. This includes the cost of all concreting materials, labour and hire charges of all T&P materials. The pole is to be installed in proper alignment as per the direction of Engineer in charge, and enclosed drawing and specification. Transportation & Installation charge with concrete work.Complete 5 years warranty.

Taking down old unsv and supply,installation & fixing of Smart integrated solar street light fitting of capacity 40 Watt & 6000 Lumens All in One Solar Hybrid type (To work with both AC & DC both) having Set polycrystalline solar cell complete with detailed technical specifications as prescribed below:- (a) System Wattage: Should not be more than 40Watts (+/-5%). (b) System Lumen Output: Should not be less than 6000 Lumen. (c) System Efficacy: Should not be less than 180 Lumens/Watt. (d) Battery Chemistry: Lithium Ferro Phosphate (LiFePO4) battery with life cycle of 2000 cycles should be used. (e)Battery Capacity: 25.6V & 24AH (f) Charging Electronics: Integrated MPPT charger with driver. (g) Charger Efficiency: >90% & Driver Efficiency: >90% (h) LED Burning Hours: Should be >50000 Hrs.@L70/ (j) IP Rating:IP65 & Ik for lens IK08 (k) Housing: Extruaion aluminium housing & Panel size 120wp (l) CCT (Color Temperature): 5700K (+/-5%) & CRI: >70 (+/- 5%) (m) Luminaire should have in-built PIR sensor. (n) Charging & Discharging LED Indicator: Should be provided inluminaire. (o) Input Voltage: 12 V DC adjusttable tilt angle(Deg.) 0- 15 deg. (p)Operating Temp Range for Light Engine: 0 to +45 Deg. C and Oparating Humidity up to 95%. and Insulation : Class III (q) Auto on/off by sensing dusk to dwn with the help PV panel & Open Circuit protection short ccircuit protection and reverse polarity Provided . (r) Manufacturer should provide LM79/ LM80 reports corresponding to the luminaire/ LED chip along with Type Test Certificate. Warranty - 3-years warranty against manufacturing defects from date of supply.

Supply & install steel tubular swaged poles Type 410 SP-31 (9.0 metres long) complete with CI base plate and finial and single swan neck including foundation(12 for street light, 03 for solar street lights) all as specified and as directed.