Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope, Go/No-Go checksEligibility, required documents, scope of work and Go/No-Go checks for this tender, in one click.
Clarification
Clarification No. 9QuestionDear UNDP Myanmar Procurement Team,We would appreciate your clarification on the technical specification of the 16L electric knapsack sprayer (Minimum flow: 2 L/min, Working pressure: 0.2–0.45 MPa):1. Does the specified minimum flow of 2 L/min refer to the pump open flow, or the actual discharge flow at the nozzle outlet?2. How should the flow rate be tested? Is it sufficient for one nozzle to meet the requirement, or **all supplied interchangeable standard nozzles** must satisfy the flow requirement?3. Is 0.45 MPa a mandatory test pressure point? Or is it acceptable to test the flow at 0.40 MPa, as long as the sprayer can be fully adjusted within the range of 0.2–0.45 MPa?4. We note that different nozzles deliver different output flow and the flow varies with working pressure, please confirm the official test protocol.Thank you for your support.Best regards.AnswerPlease be advised that your inquiry regarding the technical specifications of a 16L electric knapsack sprayer appears to have been sent to our team in error.This tender (ITB/2026/64524) strictly covers the supply of warehouse material handling equipment and industrial electric vehicles (Lots 1 through 19, including forklifts, reach trucks, pallet trucks, order pickers, tow tractors, and utility vehicles). Agricultural or chemical spraying equipment is not included in the scope of this tender.We kindly recommend verifying the ITB reference and the issuing agency/procurement team for your intended submission, as this inquiry likely pertains to a different procurement process.
Clarification
Clarification No. 8Question Dear UNOPS team,hello, we have noticed that in the Form D, there is a spread sheet with the name "Document Checklist", there are sereral documents required from Doc-1to Doc-20. Are those documents required when we provide corresponded products? Because we have not find out the bottoms to submit this kind of documents.AnswerDocuments are required to be uploaded with your offer as applicable for each Lot quoted. Each document listed in the 'Document Checklist' tab of Form D must be uploaded in the eSourcing Document Checklist under the corresponding category indicated in Column C. For example, Doc-01 to Doc-05 must be uploaded under checklist item 12: 'Technical documentation (e.g., Catalogue, Technical data sheet)' — please refer to the Document Description under this category in the Document Checklist tab of Form D.
Clarification
Clarification No. 7QuestionCould you please clarify whether a service station located in Yunnan, China which can travel to Myanmar same day for after‑sales service is acceptable to meet the mandatory local representative requirement? If not, please confirm that the local representative must be a legally incorporated entity registered in Myanmar holding valid company registration and tax documents.AnswerPlease refer to Clarification No. 2 and Clarification No. 7.No Specific Mandatory Countries: Bidders are reminded that there are no mandatory pre-determined countries for the distributor network. In accordance with Form D and Form F, bidders must demonstrate an authorized distributor network capable of providing full warranty and after-sales service in a minimum of three (3) countries in Asia and five (5) countries in Africa. Any combination of countries meeting this minimum threshold will satisfy the requirement; coverage in Myanmar is therefore not mandatory to meet the regional qualification criteria.Local Representation: A service center located in Yunnan, China may only be considered as coverage for China. Cross-border travel from an adjacent country does not fulfill the requirement of a local distributor in Myanmar. Where a bidder nominates a distributor for a specific country to meet the regional criteria or service requirements, the nominated representative must be an established, legally registered entity located within that country, possessing the necessary authorizations, facilities, and personnel to provide prompt warranty and after-sales services locally.
Clarification
Clarification No. 6QuestionWe understand that final destination countries will be confirmed when individual purchase orders are issued. Could you please clarify:Are there any anticipated or priority destination countries, particularly in Africa and Asia?Would an authorized distributor network providing warranty and after-sales services in any five African countries and any three Asian countries satisfy the requirement, or must specific countries be included?This clarification will help us coordinate with the manufacturer and verify the required service coverage before submitting our offer.Thank you for your assistance.Answer1. For indicative and informational purposes, past requests for this type of machinery have included countries/territories such as Cameroon, Eswatini, The Gambia, Mozambique, Tanzania, Uganda, Zambia, and Zanzibar. Please note that this list is non-exhaustive, non-binding, and does not limit future orders to these specific locations. Please refer to Clarification No. 22. There are no specific pre-defined countries required for the distributor network. In accordance with Form D and Form F, bidders are required to demonstrate an authorized distributor network capable of providing full warranty and after-sales service in at least five (5) countries in Africa and a minimum of three (3) countries in Asia to ensure regional support. Any combination of countries meeting this minimum threshold will satisfy the requirement.
Clarification
Clarification No. 5QuestionDear UNOPS Procurement Team,We kindly request your approval to extend the bid submission deadline to allow sufficient time to complete coordination with manufacturers and suppliers and obtain the best technical and financial offers, enabling us to submit a comprehensive and competitive bid that fully meets the tender requirements and your expectations.Thank you for your cooperation and understanding.We sincerely hope for your favorable consideration and approval.Best regards,AnswerThank you for your interest. Please note that the bid submission deadline remains unchanged at this time. All offers must be submitted through eSourcing before the deadline specified in the General Tab of the solicitation.
Clarification
Clarification No. 4QuestionDear Sirs,Reference is made to the bid currency where it was mentioned in the general terms and conditions that there would be a possibility of quoting in different Currency than in USD and relevant exchange rate for conversion would be selected on the day of closing of this tender.However, in tender particulars bid currency was clearely indicated as USD.We would like to clarify whether we may offer in EUR Currency as the products we are going to quote for are so specialized that they do have Europen Origin and our procurement would be in EUR currency. Securing an exchange rate appropriate for 120 days otr even for one year price validity would cause a tremendous exchage rate risk which we would need to cover.Thanks for your recommendation of a solution which allows us to participate.Thanks and best regardsAnswerPlease be advised that offers quoted in EUR will be accepted alongside USD.A formal tender amendment updating the Tender Particulars and Form C (Price Schedule Form) to incorporate EUR will be published in eSourcing shortly alongside the next tender amendment. In the meantime, bidders may proceed with preparing their offers in either USD or EUR.For financial evaluation and comparison purposes, offers submitted in EUR will be converted to USD using the official United Nations Operational Rates of Exchange (UNORE) prevailing on the date of the ITB submission deadline (accessible at: https://treasury.un.org/operationalrates/OperationalRates.php ). Any resulting Long Term Agreement (LTA), Purchase Orders, and payments will be strictly issued and made in the approved quoted currency (USD or EUR).
Clarification
Clarification No. 3Question Bonjour, Je voudrais juste avoir une idée exacte des pays bénéficiaires. MerciAnswerPlease refer to Clarification No. 2
Clarification
Clarification No. 2Question Dear Sir/Madam,Could you please confirm the countries in which the forklifts will be used?AnswerPlease refer to the Tender Particulars, Scope of Bid in the eSourcing system and Section II: Schedule of Requirements .As this solicitation is intended to establish non-exclusive Long Term Agreements (LTAs) for UN Web Buy Plus (www.unwebbuyplus.org), selected items will be displayed in an electronic catalogue for global use by UNOPS clients worldwide.Specific destination countries, quantities, and delivery details are not pre-determined at this stage. Destination countries and consignee information will only be confirmed when individual Call-off Orders (Purchase Orders) are placed as actual requirements arise.Please note that, in accordance with Form D and Form F, bidders must demonstrate an authorized distributor network capable of providing full warranty and after-sales service (at least 5 countries in Africa and a minimum of 3 countries in Asia) to ensure regional support when orders are issued.
Clarification
Clarification No. 1 QuestionDear Sir/Madam,Greetings!We are interested in participating in the tender referenced above and would appreciate your clarification regarding the exact delivery location, including the destination country and specific delivery address, if available.Thank you for your time and assistance. We look forward to your response.AnswerPlease refer to the Tender Particulars, Scope of Bid, and Section II: Schedule of Requirements in the eSourcing system.As indicated, this tender is intended to establish non-exclusive Long Term Agreements (LTAs) with multiple vendors for the supply of manual and electric Material Handling Equipment for UN Web Buy Plus (UNOPS e-commerce platform) for global use across multiple destinations worldwide. Selected units will be displayed in electronic catalogues on UN Web Buy Plus (http://www.unwebbuyplus.org), allowing UNOPS clients to place orders without further tendering.Regarding delivery locations and quantities, please note the following:No Minimum Quantity / Undefined Destinations at this Stage: No specific quantities are requested at this stage. UNOPS commits to no minimum purchase volume or quantity. Orders with determined quantities, destination countries, and consignee details will be issued via individual Call-off Orders (Purchase Orders) only if and when an actual requirement arises.Pricing and Delivery Terms (FCA): Bidders must quote prices on an FCA (Free Carrier) basis to the sea port or airport closest to their manufacturing or stockholding facility. In most cases, UNOPS will appoint an international freight forwarder to handle transit and collect items directly from the designated FCA points.LTA Duration: The results of this solicitation will be used to establish non-exclusive LTAs for an initial period of three (3) years, with the possibility of extension for up to an additional two (1+1) years, subject to satisfactory performance and mutual agreement.Warranty and After-Sales Network: As specified in Form D for each lot, bidders must demonstrate an authorized distributor network capable of providing full warranty and after-sales service in at least 5 countries in the Africa region and a minimum of 3 countries in Asia. Bidders must submit the list of distributors with full contact details in Form F. The nominated local distributor shall be responsible for the warranty and maintenance of the base item and all associated equipment. Failure to demonstrate the required regional coverage will exclude the bidder from further evaluation.
Tender Value
Refer Docs
Bid Security (EMD)
Refer Docs
Closing Date
30 Nov 2026, 11:00 (UTC)30 Nov 2026, 4:30 pm IST
Eligibility, documents, scope, Go/No-Go checksEligibility, required documents, scope of work and Go/No-Go checks for this tender, in one click.
This tender is for the Supply of manual and electric Material Handling Equipment for UN Web Buy Plus (UNOPS e-commerce platform) for multiple destinations worldwide. UNOPS wishes to establish non-exclusive Long Term Agreements (LTAs) with more than one vendor and to display the selected units in electronic catalogues on UN Web Buy Plus (http://www.unwebbuyplus.org) allowing UNOPS clients to order without further tendering. Quantities are undefined. UNOPS will not be committed to purchase any minimum quantity, and purchases will be made only if and when there is an actual requirement. IMPORTANT NOTE: Interested vendors must respond to this tender using the UNOPS eSourcing system, via the UNGM portal. In order to access the full UNOPS tender details, request clarifications on the tender, and submit a vendor response to a tender using the system, vendors need to be registered as a UNOPS vendor at the UNGM portal and be logged into UNGM. For guidance on how to register on UNGM and submit responses to UNOPS tenders in the UNOPS eSourcing system, please refer to the user guide and other resources available at: https://esourcing.unops.org/#/Help/Guides Interested in improving your knowledge of what UNOPS procures, how we procure and how to become a vendor to supply to our organization? Learn more about our free online course on “Doing business with UNOPS” here
318781
ITB/2026/64524
Invitation to bid
Afghanistan, Albania, Algeria, American Samoa, Andorra, Angola, Anguilla, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, British Indian Ocean Territory, Brunei, Bulgaria, Burkina Faso, Burundi, Cambodia, Cameroon, Canada, Cabo Verde, Cayman Islands, Central African Republic, Chad, Chile, China, Christmas Island, Colombia, Comoros, Republic of the Congo, Cook Islands, Costa Rica, Côte d’Ivoire, Croatia, Cuba, Cyprus, Czechia, Democratic Republic of the Congo, Denmark, Djibouti, Dominica, Dominican Republic, Timor-Leste, Ecuador, Egypt, El Salvador, Equatorial Guinea, Eritrea, Estonia, Ethiopia, Falkland Islands, Faroe Islands, Fiji, Finland, France, French Guiana, French Polynesia, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Greenland, Grenada, Guadeloupe, Guam, Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Indonesia, Iran, Iraq, Ireland, Israel, Italy, Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati, North Korea, South Korea, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Libya, Liechtenstein, Lithuania, Luxembourg, Macao, North Macedonia, Madagascar, Malawi, Malaysia, Maldives, Mali, Malta, Marshall Islands, Martinique, Mauritania, Mauritius, Mayotte, Mexico, Micronesia, Moldova, Monaco, Mongolia, Montserrat, Morocco, Mozambique, Myanmar, Namibia, Nauru, Nepal, Netherlands, New Caledonia, New Zealand, Nicaragua, Niger, Nigeria, Niue, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, Philippines, Pitcairn Islands, Poland, Portugal, Puerto Rico, Qatar, Réunion, Romania, Russia, Rwanda, Saint Helena, Saint Kitts and Nevis, Saint Lucia, Saint Pierre and Miquelon, Saint Vincent and the Grenadines, Samoa, San Marino, São Tomé and Príncipe, Saudi Arabia, Senegal, Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, Solomon Islands, Somalia, South Africa, Spain, Sri Lanka, Sudan, Suriname, Svalbard and Jan Mayen, Eswatini, Sweden, Switzerland, Syria, Taiwan, Tajikistan, Thailand, Togo, Tokelau, Tonga, Trinidad and Tobago, Tunisia, Türkiye, Turkmenistan, Turks and Caicos Islands, Tuvalu, Uganda, Ukraine, United Arab Emirates, United Kingdom, Tanzania, United States, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, British Virgin Islands, United States Virgin Islands, Wallis and Futuna, Western Sahara, Yemen, Zambia, Zimbabwe, Antarctica, Palestine, Serbia, Montenegro, Kosovo, South Sudan
INVITATION
UTC
21 Nov 2026
19 Oct 2026
ITB reference: ITB/2026/64524
Name of Bidder:
Lot Category Capacity / lift height / operating range Offered
1 Electric Counterbalance Forklift, Light Duty (1 - 1.8 ton) Lifting capacity 1.0 to 1.8 ton, standard lift min 3.0 m
2 Electric Counterbalance Forklift, Medium Duty (1.8 - 2.5 ton) Lifting capacity 1.8 to 2.5 ton, standard lift min 4.5 m
3 Electric Counterbalance Forklift, Heavy Duty (2.5 - 3.5 ton) Lifting capacity 2.5 to 3.5 ton, standard lift min 4.5 m
4 Electric Reach Truck, Standard Reach Lifting capacity 1.4 to 1.8 ton, operating range 7.5 to 10.0 m
5 Electric Reach Truck, High Reach Lifting capacity min 1.6 ton, operating range 10.0 to 12.5 m
6 Electric Reach Truck, Articulated ("Bendi"-type) Lifting capacity 2.0 ton, operating range 7.5 to 12.4 m
7 VNA Machine, Very Narrow Aisle (Man-Up) Lifting capacity 1.0 to 1.5 ton, lift height up to 13.8 m
8 Electric Pallet Truck, Low Lift – Walkie Lifting capacity 1.4 to 2.5 ton, horizontal transport
9 Electric Pallet Truck, Low Lift – Rider Lifting capacity 2.5 to 3.5 ton, horizontal transport
10 Electric Pallet Truck / Stacker, High Lift – Walkie Stacker Lifting capacity 1.0 to 1.6 ton, stacking up to 4.5 m
11 Manual Pallet Jack Lifting capacity min 3 ton, fork height range approx. 85 to 200 mm
12 Electric Order Picker, Low Level Lifting capacity 1.0 ton, platform elevation max 2.0 m
13 Electric Order Picker, Medium Level Lifting capacity 1.0 ton, platform elevation max 6.0 m
14 Electric Order Picker, High Level – Man Up Lifting capacity 1.0 ton, platform elevation max 10.0 m
15 Tow Tractor, Light Duty Tow Towing capacity 1.5 to 3.0 ton, horizontal transport
16 Tow Tractor, Medium Duty Tow Towing capacity 3.0 ton, horizontal transport
17 Trailers / Carts (towed equipment) Different type and capacity trolleys
18 Electric Utility/Pick-up Vehicle, Light Utility Payload capacity 0.4 to 0.7 ton, horizontal transport
19 Electric Utility/Pick-up Vehicle, Medium Utility Payload capacity min 0.7 ton, horizontal transport
ITB reference no: ITB/2026/64524
Name of Bidder:
Lot Description Unit of measure Supplier product reference number Make Supplier product name / Model Country of origin Unit of measure FCA point(s) of delivery for seafreight (Port) (Exact address: street, city, Country) FCA point(s) of delivery for airfreight (Airport) (Exact address: street, city, Country) Delivery lead time* (in weeks) Currency FCA Unit price (Qty 1)
1 Electric Counterbalance Forklift, Light Duty (1 - 1.8 ton) Unit USD
2 Electric Counterbalance Forklift, Medium Duty (1.8 - 2.5 ton) Unit USD
3 Electric Counterbalance Forklift, Heavy Duty (2.5 - 3.5 ton) Unit USD
4 Electric Reach Truck, Standard Reach Unit USD
5 Electric Reach Truck, High Reach Unit USD
6 Electric Reach Truck, Articulated ("Bendi"-type) Unit USD
7 VNA Machine, Very Narrow Aisle (Man-Up) Unit USD
8 Electric Pallet Truck, Low Lift – Walkie Unit USD
9 Electric Pallet Truck, Low Lift – Rider Unit USD
10 Electric Pallet Truck / Stacker, High Lift – Walkie Stacker Unit USD
11 Manual Pallet Jack Unit USD
12 Electric Order Picker, Low Level Unit USD
13 Electric Order Picker, Medium Level Unit USD
14 Electric Order Picker, High Level – Man Up Unit USD
15 Tow Tractor, Light Duty Tow Unit USD
16 Tow Tractor, Medium Duty Tow Unit USD
17 Trailers / Carts (towed equipment) Unit USD
18 Electric Utility/Pick-up Vehicle, Light Utility Unit USD
19 Electric Utility/Pick-up Vehicle, Medium Utility Unit USD
* Delivery lead time: from the date supplier acknowledges / signs UNOPS Purchase order (PO) to the date the goods from supplier are ready for shipment at the FCA point of delivery
Lot 1: Electric Counterbalance Forklift, Light Duty (1 - 1.8 ton)
Lifting capacity 1.0 to 1.8 ton, standard lift min 3.0 m
Country of origin:
Item UNOPS Desireble options Description Unit of measure Unit Price USD
Please enter further available options as applicable. If Standard, state "Standard".
49 Repair manual in one or more of English, Spanish, French, Arabic, please indicate.
50 Rear towing coupling/hitch/hook
51 Electric rotating beacon/flashing beacon.
52 Spare parts kit, 1 year / 1,500 hours of operation, min.
53 Alternative Lithium-ion (Li-ion/LFP) Battery Options (e.g. other capacities in kWh)
54 Battery end-of-life: Manufacturer-supported take-back/recycling programme.
55 Cold chain configuration: Equipment rated for continuous operation in cold storage down to -20°C, comprising: - Anti-condensation protection for electrical and electronic assemblies; - Low-temperature-rated hydraulic oil, cold-rated seals, and cold-store tyres/wheels; - Battery self-heating system with BMS low-temperature charge inhibit; - Enclosed cold-store cabin (where available/applicable for the offered model): glass all around, cabin heating, heated front/rear glass (or de-misting system), wipers, and interior/exterior mirrors; - Operator seat/platform heating where an enclosed cabin is not fitted or not standard. Bidder to state the operating temperature range of camera, monitor, and fork laser where fitted. To be quoted as a separate unit price and not included in the base price.
56 Higher-output charger (e.g. a three-phase 400 V charger) - Bidder to define
57 Extended Warranty for 1 year or 3,000 hours of operation, whichever comes first
58 Extended Warranty for 1 year for the battery
Lot 2: Electric Counterbalance Forklift, Medium Duty (1.8 - 2.5 ton)
Lifting capacity 1.8 to 2.5 ton, standard lift min 4.5 m
Country of origin:
Item UNOPS Desireble options Description Unit of measure Unit Price USD
Please enter further available options as applicable. If Standard, state "Standard".
49 Repair manual in one or more of English, Spanish, French, Arabic, please indicate.
50 Rear towing coupling/hitch/hook
51 Electric rotating beacon/flashing beacon.
52 Spare parts kit, 1 year / 1,500 hours of operation, min.
53 Alternative Lithium-ion (Li-ion/LFP) Battery Options (e.g. other capacities in kWh)
54 Battery end-of-life: Manufacturer-supported take-back/recycling programme.
55 Cold chain configuration: Equipment rated for continuous operation in cold storage down to -20°C, comprising: - Anti-condensation protection for electrical and electronic assemblies; - Low-temperature-rated hydraulic oil, cold-rated seals, and cold-store tyres/wheels; - Battery self-heating system with BMS low-temperature charge inhibit; - Enclosed cold-store cabin (where available/applicable for the offered model): glass all around, cabin heating, heated front/rear glass (or de-misting system), wipers, and interior/exterior mirrors; - Operator seat/platform heating where an enclosed cabin is not fitted or not standard. Bidder to state the operating temperature range of camera, monitor, and fork laser where fitted. To be quoted as a separate unit price and not included in the base price.
56 Higher-output charger (e.g. a three-phase 400 V charger) - Bidder to define
57 Extended Warranty for 1 year or 3,000 hours of operation, whichever comes first
58 Extended Warranty for 1 year for the battery
Lot 3: Electric Counterbalance Forklift, Heavy Duty (2.5 - 3.5 ton)
Lifting capacity 2.5 to 3.5 ton, standard lift min 4.5 m
Country of origin:
Item UNOPS Desireble options Description Unit of measure Unit Price USD
Please enter further available options as applicable. If Standard, state "Standard".
51 Repair manual in one or more of English, Spanish, French, Arabic, please indicate.
52 Electric rotating beacon/flashing beacon.
53 Spare parts kit, 1 year / 1,500 hours of operation, min.
54 Alternative Lithium-ion (Li-ion/LFP) Battery Options (e.g. other capacities in kWh)
55 Battery end-of-life: Manufacturer-supported take-back/recycling programme.
56 Cold chain configuration: Equipment rated for continuous operation in cold storage down to -20°C, comprising: - Anti-condensation protection for electrical and electronic assemblies; - Low-temperature-rated hydraulic oil, cold-rated seals, and cold-store tyres/wheels; - Battery self-heating system with BMS low-temperature charge inhibit; - Enclosed cold-store cabin (where available/applicable for the offered model): glass all around, cabin heating, heated front/rear glass (or de-misting system), wipers, and interior/exterior mirrors; - Operator seat/platform heating where an enclosed cabin is not fitted or not standard. Bidder to state the operating temperature range of camera, monitor, and fork laser where fitted. To be quoted as a separate unit price and not included in the base price.
57 Higher-output charger (e.g. a three-phase 400 V charger) - Bidder to define
58 Extended Warranty for 1 year or 3,000 hours of operation, whichever comes first
59 Extended Warranty for 1 year for the battery
Lot 4: Electric Reach Truck, Standard Reach
Lifting capacity 1.4 to 1.8 ton, operating range 7.5 to 10.0 m
Country of origin:
Item UNOPS Desireble options Description Unit of measure Unit Price USD
Please enter further available options as applicable. If Standard, state "Standard".
51 Repair manual in one or more of English, Spanish, French, Arabic, please indicate.
52 Electric rotating beacon/flashing beacon.
53 Spare parts kit, 1 year / 1,500 hours of operation, min.
54 Alternative Lithium-ion (Li-ion/LFP) Battery Options (e.g. other capacities in kWh)
55 Battery end-of-life: Manufacturer-supported take-back/recycling programme.
56 Cold chain configuration: Equipment rated for continuous operation in cold storage down to -20°C, comprising: - Anti-condensation protection for electrical and electronic assemblies; - Low-temperature-rated hydraulic oil, cold-rated seals, and cold-store tyres/wheels; - Battery self-heating system with BMS low-temperature charge inhibit; - Enclosed cold-store cabin (where available/applicable for the offered model): glass all around, cabin heating, heated front/rear glass (or de-misting system), wipers, and interior/exterior mirrors; - Operator seat/platform heating where an enclosed cabin is not fitted or not standard. Bidder to state the operating temperature range of camera, monitor, and fork laser where fitted. To be quoted as a separate unit price and not included in the base price.
57 Higher-output charger (e.g. a three-phase 400 V charger) - Bidder to define
58 Extended Warranty for 1 year or 3,000 hours of operation, whichever comes first
59 Extended Warranty for 1 year for the battery
Lot 5: Electric Reach Truck, High Reach
Lifting capacity min 1.6 ton, operating range 10.0 to 12.5 m
Country of origin:
Item UNOPS Desireble options Description Unit of measure Unit Price USD
Please enter further available options as applicable. If Standard, state "Standard".
50 Repair manual in one or more of English, Spanish, French, Arabic, please indicate.
51 Electric rotating beacon/flashing beacon.
52 Spare parts kit, 1 year / 1,500 hours of operation, min.
53 Alternative Lithium-ion (Li-ion/LFP) Battery Options (e.g. other capacities in kWh)
54 Battery end-of-life: Manufacturer-supported take-back/recycling programme.
55 Cold chain configuration: Equipment rated for continuous operation in cold storage down to -20°C, comprising: - Anti-condensation protection for electrical and electronic assemblies; - Low-temperature-rated hydraulic oil, cold-rated seals, and cold-store tyres/wheels; - Battery self-heating system with BMS low-temperature charge inhibit; - Enclosed cold-store cabin (where available/applicable for the offered model): glass all around, cabin heating, heated front/rear glass (or de-misting system), wipers, and interior/exterior mirrors; - Operator seat/platform heating where an enclosed cabin is not fitted or not standard. Bidder to state the operating temperature range of camera, monitor, and fork laser where fitted. To be quoted as a separate unit price and not included in the base price.
56 Higher-output charger (e.g. a three-phase 400 V charger) - Bidder to define
57 Extended Warranty for 1 year or 3,000 hours of operation, whichever comes first
58 Extended Warranty for 1 year for the battery
Lot 6: Electric Reach Truck, Articulated ("Bendi"-type)
Lifting capacity 2.0 ton, operating range 7.5 to 12.4 m
Country of origin:
Item UNOPS Minimum Technical Requirement Description Unit of measure Unit Price USD
Please enter further available options as applicable. If Standard, state "Standard".
50 Repair manual in one or more of English, Spanish, French, Arabic, please indicate.
51 Electric rotating beacon/flashing beacon.
52 Spare parts kit, 1 year / 1,500 hours of operation, min.
53 Alternative Lithium-ion (Li-ion/LFP) Battery Options (e.g. other capacities in kWh)
54 Battery end-of-life: Manufacturer-supported take-back/recycling programme.
55 Cold chain configuration: Equipment rated for continuous operation in cold storage down to -20°C, comprising: - Anti-condensation protection for electrical and electronic assemblies; - Low-temperature-rated hydraulic oil, cold-rated seals, and cold-store tyres/wheels; - Battery self-heating system with BMS low-temperature charge inhibit; - Enclosed cold-store cabin (where available/applicable for the offered model): glass all around, cabin heating, heated front/rear glass (or de-misting system), wipers, and interior/exterior mirrors; - Operator seat/platform heating where an enclosed cabin is not fitted or not standard. Bidder to state the operating temperature range of camera, monitor, and fork laser where fitted. To be quoted as a separate unit price and not included in the base price.
56 Higher-output charger (e.g. a three-phase 400 V charger) - Bidder to define
57 Extended Warranty for 1 year or 3,000 hours of operation, whichever comes first
58 Extended Warranty for 1 year for the battery
Lot 7: VNA Machine, Very Narrow Aisle (Man-Up)
Lifting capacity 1.0 to 1.5 ton, lift height up to 13.8 m
Country of origin:
Item UNOPS Minimum Technical Requirement Description Unit of measure Unit Price USD
Please enter further available options as applicable. If Standard, state "Standard".
46 Repair manual in one or more of English, Spanish, French, Arabic, please indicate.
47 Electric rotating beacon/flashing beacon.
48 Spare parts kit, 1 year / 1,500 hours of operation, min.
49 Wire-guidance retrofit kit, if not standard.
50 Alternative Lithium-ion (Li-ion/LFP) Battery Options (e.g. other capacities in kWh)
51 Battery end-of-life: Manufacturer-supported take-back/recycling programme.
52 Cold chain configuration: Equipment rated for continuous operation in cold storage down to -20°C, comprising: - Anti-condensation protection for electrical and electronic assemblies; - Low-temperature-rated hydraulic oil, cold-rated seals, and cold-store tyres/wheels; - Battery self-heating system with BMS low-temperature charge inhibit; - Enclosed cold-store cabin (where available/applicable for the offered model): glass all around, cabin heating, heated front/rear glass (or de-misting system), wipers, and interior/exterior mirrors; - Operator seat/platform heating where an enclosed cabin is not fitted or not standard. Bidder to state the operating temperature range of camera, monitor, and fork laser where fitted. To be quoted as a separate unit price and not included in the base price.
53 Higher-output charger (e.g. a three-phase 400 V charger) - Bidder to define
54 Extended Warranty for 1 year or 3,000 hours of operation, whichever comes first
55 Extended Warranty for 1 year for the battery
Lot 8: Electric Pallet Truck, Low Lift – Walkie
Lifting capacity 1.4 to 2.5 ton, horizontal transport
Country of origin:
Item UNOPS Minimum Technical Requirement Description Unit of measure Unit Price USD
Please enter further available options as applicable. If Standard, state "Standard".
37 Repair manual in one or more of English, Spanish, French, Arabic, please indicate.
38 Spare parts kit, 1 year / 1,500 hours of operation, min.
39 Alternative Lithium-ion (Li-ion/LFP) Battery Options (e.g. other capacities in kWh)
40 Battery end-of-life: Manufacturer-supported take-back/recycling programme.
41 Cold chain configuration: equipment rated for continuous operation in cold storage down to -20 degrees C, comprising anti-condensation protection for electrical and electronic assemblies, low-temperature-rated hydraulic oil, cold-rated seals and wheels, battery self-heating with BMS low-temperature charge inhibit, and operator heating where an enclosed or seated operator position exists. Bidder to state the operating temperature range of camera, monitor and fork laser where fitted. To be quoted as a separate unit price and not included in the base price.
42 Higher-output charger (e.g. a three-phase 400 V charger) - Bidder to define
43 Extended Warranty for 1 year or 3,000 hours of operation, whichever comes first
44 Extended Warranty for 1 year for the battery
Lot 9: Electric Pallet Truck, Low Lift – Rider
Lifting capacity 2.5 to 3.5 ton, horizontal transport
Country of origin:
Item UNOPS Minimum Technical Requirement Description Unit of measure Unit Price USD
Please enter further available options as applicable. If Standard, state "Standard".
40 Repair manual in one or more of English, Spanish, French, Arabic, please indicate.
41 Electric rotating beacon/flashing beacon.
42 Spare parts kit, 1 year / 1,500 hours of operation, min.
43 Alternative Lithium-ion (Li-ion/LFP) Battery Options (e.g. other capacities in kWh)
44 Battery end-of-life: Manufacturer-supported take-back/recycling programme.
45 Cold chain configuration: equipment rated for continuous operation in cold storage down to -20 degrees C, comprising anti-condensation protection for electrical and electronic assemblies, low-temperature-rated hydraulic oil, cold-rated seals and wheels, battery self-heating with BMS low-temperature charge inhibit, and operator heating where an enclosed or seated operator position exists. Bidder to state the operating temperature range of camera, monitor and fork laser where fitted. To be quoted as a separate unit price and not included in the base price.
46 Higher-output charger (e.g. a three-phase 400 V charger) - Bidder to define
47 Extended Warranty for 1 year or 3,000 hours of operation, whichever comes first
48 Extended Warranty for 1 year for the battery
Lot 10: Electric Pallet Truck / Stacker, High Lift – Walkie Stacker
Lifting capacity 1.0 to 1.6 ton, stacking up to 4.5 m
Country of origin:
Item UNOPS Minimum Technical Requirement Description Unit of measure Unit Price USD
Please enter further available options as applicable. If Standard, state "Standard".
40 Repair manual in one or more of English, Spanish, French, Arabic, please indicate.
41 Electric rotating beacon/flashing beacon.
42 Spare parts kit, 1 year / 1,500 hours of operation, min.
43 Alternative Lithium-ion (Li-ion/LFP) Battery Options (e.g. other capacities in kWh)
44 Battery end-of-life: Manufacturer-supported take-back/recycling programme.
45 Cold chain configuration: equipment rated for continuous operation in cold storage down to -20 degrees C, comprising anti-condensation protection for electrical and electronic assemblies, low-temperature-rated hydraulic oil, cold-rated seals and wheels, battery self-heating with BMS low-temperature charge inhibit, and operator heating where an enclosed or seated operator position exists. Bidder to state the operating temperature range of camera, monitor and fork laser where fitted. To be quoted as a separate unit price and not included in the base price.
46 Higher-output charger (e.g. a three-phase 400 V charger) - Bidder to define
47 Extended Warranty for 1 year or 3,000 hours of operation, whichever comes first
48 Extended Warranty for 1 year for the battery
49 Operator stand-on platform (foldable or fixed), if not included as standard in base offered model
Lot 11: Manual Pallet Jack
Lifting capacity min 3 ton, fork height range approx. 85 to 200 mm
Country of origin:
Item UNOPS Minimum Technical Requirement Description Unit of measure Unit Price USD
Please enter further available options as applicable. If Standard, state "Standard".
20 Repair/service manual in one or more of English, Spanish, French, Arabic, please indicate.
21 Spare seal/wheel kit for preventative maintenance.
22 Cold chain configuration: low-temperature-rated hydraulic oil and cold-rated seals and wheels for continuous operation in cold storage down to -20 degrees C. To be quoted as a separate unit price and not included in the base price.
23 Extended Warranty for 1 year
Lot 12: Electric Order Picker, Low Level
Lifting capacity 1.0 ton, platform elevation max 2.0 m
Country of origin:
Item UNOPS Minimum Technical Requirement Description Unit of measure Unit Price USD
Please enter further available options as applicable. If Standard, state "Standard".
38 Repair manual in one or more of English, Spanish, French, Arabic, please indicate.
39 Spare parts kit, 1 year / 1,500 hours of operation, min.
40 Alternative Lithium-ion (Li-ion/LFP) Battery Options (e.g. other capacities in kWh)
41 Battery end-of-life: Manufacturer-supported take-back/recycling programme.
42 Cold chain configuration: equipment rated for continuous operation in cold storage down to -20 degrees C, comprising anti-condensation protection for electrical and electronic assemblies, low-temperature-rated hydraulic oil, cold-rated seals and wheels, battery self-heating with BMS low-temperature charge inhibit, and operator heating where an enclosed or seated operator position exists. Bidder to state the operating temperature range of camera, monitor and fork laser where fitted. To be quoted as a separate unit price and not included in the base price.
43 Higher-output charger (e.g. a three-phase 400 V charger) - Bidder to define
44 Extended Warranty for 1 year or 3,000 hours of operation, whichever comes first
45 Extended Warranty for 1 year for the battery
Lot 13: Electric Order Picker, Medium Level
Lifting capacity 1.0 ton, platform elevation max 6.0 m
Country of origin:
Item UNOPS Minimum Technical Requirement Description Unit of measure Unit Price USD
Please enter further available options as applicable. If Standard, state "Standard".
40 Repair manual in one or more of English, Spanish, French, Arabic, please indicate.
41 Spare parts kit, 1 year / 1,500 hours of operation, min.
42 Integrated barcode scanner/computer terminal mounting.
43 Alternative Lithium-ion (Li-ion/LFP) Battery Options (e.g. other capacities in kWh)
44 Battery end-of-life: Manufacturer-supported take-back/recycling programme.
45 Mechanical rail guidance system (chassis guide rollers): Bidder to state achieved working aisle width (max 1,930 mm), guide roller dimensions, required rail gauge/clearance, and transfer aisle width
46 Wire/inductive guidance system (on-board sensors & steering controller): Bidder to state achieved working aisle width (max 1,930 mm), wire frequency/compatibility, guidance tolerance, and transfer aisle width. Bidder to provide full pre-installation technical requirements.
46a On-truck guidance equipment: On-board sensors and steering controller fitted to the truck. Priced per truck.
46b Frequency generator: Stationary line driver/frequency generator unit to energize the floor wire loop. Priced per unit.
46c Floor wire installation: Floor slot cutting, wire laying, joint sealing, and commissioning. Bidder to state floor requirements before installation. Floor repair or levelling is excluded. Priced per linear meter of aisle.
47 Cold chain configuration: equipment rated for continuous operation in cold storage down to -20 degrees C, comprising anti-condensation protection for electrical and electronic assemblies, low-temperature-rated hydraulic oil, cold-rated seals and wheels, battery self-heating with BMS low-temperature charge inhibit, and operator heating where an enclosed or seated operator position exists. To be quoted as a separate unit price and not included in the base price.
48 Higher-output charger (e.g. a three-phase 400 V charger) - Bidder to define
49 Extended Warranty for 1 year or 3,000 hours of operation, whichever comes first
50 Extended Warranty for 1 year for the battery
Lot 14: Electric Order Picker, High Level – Man Up
Lifting capacity 1.0 ton, platform elevation max 10.0 m
Country of origin:
Item UNOPS Minimum Technical Requirement Description Unit of measure Unit Price USD
Please enter further available options as applicable. If Standard, state "Standard".
39 Repair manual in one or more of English, Spanish, French, Arabic, please indicate.
40 Spare parts kit, 1 year / 1,500 hours of operation, min.
41 Integrated barcode scanner/computer terminal mounting.
42 Alternative Lithium-ion (Li-ion/LFP) Battery Options (e.g. other capacities in kWh)
43 Battery end-of-life: Manufacturer-supported take-back/recycling programme.
44 Mechanical rail guidance system (chassis guide rollers): Bidder to state achieved working aisle width (max 1,930 mm), guide roller dimensions, required rail gauge/clearance, and transfer aisle width
45 Wire/inductive guidance system (on-board sensors & steering controller): Bidder to state achieved working aisle width (max 1,930 mm), wire frequency/compatibility, guidance tolerance, and transfer aisle width. Bidder to provide full pre-installation technical requirements.
45a On-truck guidance equipment: On-board sensors and steering controller fitted to the truck. Priced per truck.
45b Frequency generator: Stationary line driver/frequency generator unit to energize the floor wire loop. Priced per unit.
45c Floor wire installation: Floor slot cutting, wire laying, joint sealing, and commissioning. Bidder to state floor requirements before installation. Floor repair or levelling is excluded. Priced per linear meter of aisle.
46 Cold chain configuration: equipment rated for continuous operation in cold storage down to -20 degrees C, comprising anti-condensation protection for electrical and electronic assemblies, low-temperature-rated hydraulic oil, cold-rated seals and wheels, battery self-heating with BMS low-temperature charge inhibit, and operator heating where an enclosed or seated operator position exists. To be quoted as a separate unit price and not included in the base price.
47 Higher-output charger (e.g. a three-phase 400 V charger) - Bidder to define
48 Extended Warranty for 1 year or 3,000 hours of operation, whichever comes first
49 Extended Warranty for 1 year for the battery
Lot 15: Tow Tractor, Light Duty Tow
Towing capacity 1.5 to 3.0 ton, horizontal transport
Country of origin:
Item UNOPS Minimum Technical Requirement Description Unit of measure Unit Price USD
Please enter further available options as applicable. If Standard, state "Standard".
40 Repair manual in one or more of English, Spanish, French, Arabic, please indicate.
41 Electric rotating beacon/flashing beacon.
42 Spare parts kit, 1 year / 1,500 hours of operation, min.
43 Secondary hitch point for multi-trailer (train) configuration.
44 Alternative Lithium-ion (Li-ion/LFP) Battery Options (e.g. other capacities in kWh)
45 Battery end-of-life: Manufacturer-supported take-back/recycling programme.
46 Cold chain configuration: equipment rated for continuous operation in cold storage down to -20 degrees C, comprising anti-condensation protection for electrical and electronic assemblies, low-temperature-rated hydraulic oil, cold-rated seals and wheels, battery self-heating with BMS low-temperature charge inhibit, and operator heating where an enclosed or seated operator position exists. Bidder to state the operating temperature range of camera, monitor and fork laser where fitted. To be quoted as a separate unit price and not included in the base price.
47 Higher-output charger (e.g. a three-phase 400 V charger) - Bidder to define
48 Extended Warranty for 1 year or 3,000 hours of operation, whichever comes first
49 Extended Warranty for 1 year for the battery
Lot 16: Tow Tractor, Medium Duty Tow
Towing capacity 3.0 ton, horizontal transport
Country of origin:
Item UNOPS Minimum Technical Requirement Description Unit of measure Unit Price USD
Please enter further available options as applicable. If Standard, state "Standard".
42 Repair manual in one or more of English, Spanish, French, Arabic, please indicate.
43 Electric rotating beacon/flashing beacon.
44 Spare parts kit, 1 year / 1,500 hours of operation, min.
45 Alternative Lithium-ion (Li-ion/LFP) Battery Options (e.g. other capacities in kWh)
46 Battery end-of-life: Manufacturer-supported take-back/recycling programme.
47 Cold chain configuration: equipment rated for continuous operation in cold storage down to -20 degrees C, comprising anti-condensation protection for electrical and electronic assemblies, low-temperature-rated hydraulic oil, cold-rated seals and wheels, battery self-heating with BMS low-temperature charge inhibit, and operator heating where an enclosed or seated operator position exists. Bidder to state the operating temperature range of camera, monitor and fork laser where fitted. To be quoted as a separate unit price and not included in the base price.
48 Higher-output charger (e.g. a three-phase 400 V charger) - Bidder to define
49 Extended Warranty for 1 year or 3,000 hours of operation, whichever comes first
50 Extended Warranty for 1 year for the battery
Lot 17: Trailers / Carts (towed equipment)
Different type and capacity trolleys
Country of origin:
Item UNOPS Minimum Technical Requirement Description Unit of measure Unit Price USD
Please enter further available options as applicable. If Standard, state "Standard".
18 Type: roller-bed trailer for pallet loading-dock transfer
19 Type: mesh/cage trolley
20 High Capacity unit, ton, min 2
21 Removable mesh/cage sides for the flatbed/platform sub-type.
22 Tipping/dump mechanism for the cage sub-type.
23 Cold chain configuration: cold-rated wheels/castors, bearings, fasteners and deck/frame finish for continuous operation in cold storage down to -20 degrees C. To be quoted as a separate unit price and not included in the base price.
24 Extended Warranty for 1 year.
Lot 18: Electric Utility/Pick-up Vehicle, Light Utility
Payload capacity 0.4 to 0.7 ton, horizontal transport
Country of origin:
Item UNOPS Minimum Technical Requirement Description Unit of measure Unit Price USD
Please enter further available options as applicable. If Standard, state "Standard".
41 Repair manual in one or more of English, Spanish, French, Arabic, please indicate.
42 Electric rotating beacon/flashing beacon.
43 Lockable cargo box/security lid.
44 Spare parts kit, 1 year / 1,500 hours of operation, min.
45 Alternative Lithium-ion (Li-ion/LFP) Battery Options (e.g. other capacities in kWh)
46 Battery end-of-life: Manufacturer-supported take-back/recycling programme.
47 Higher-output charger (e.g. a three-phase 400 V charger) - Bidder to define
48 Extended Warranty for 1 year or 3,000 hours of operation, whichever comes first
49 Extended Warranty for 1 year for the battery
Lot 19: Electric Utility/Pick-up Vehicle, Medium Utility
Payload capacity min 0.7 ton, horizontal transport
Country of origin:
Item UNOPS Minimum Technical Requirement Description Unit of measure Unit Price USD
Please enter further available options as applicable. If Standard, state "Standard".
41 Repair manual in one or more of English, Spanish, French, Arabic, please indicate.
42 Electric rotating beacon/flashing beacon.
43 Lockable cargo box/security lid.
44 Spare parts kit, 1 year / 1,500 hours of operation, min.
45 Alternative Lithium-ion (Li-ion/LFP) Battery Options (e.g. other capacities in kWh)
46 Battery end-of-life: Manufacturer-supported take-back/recycling programme.
47 Higher-output charger (e.g. a three-phase 400 V charger) - Bidder to define
48 Extended Warranty for 1 year or 3,000 hours of operation, whichever comes first
49 Extended Warranty for 1 year for the battery
Form D - Technical Bid Form
Name of Bidder:
INSTRUCTIONS: - Bidders are requested to complete the table below indicating which Lots are part of the offer. - Bidders are requested to complete the Minimum Technical Requirements Compliance Tables (in tabs 'Lot 1' to 'Lot 19') to demonstrate their proposal meets UNOPS Minimum Technical Requirements: - Bidders are NOT allowed to make modifications to the column 'UNOPS minimum technical requirements'. Such modifications will constitute a reason for disqualification. - Mark compliance in column C: Complies (Yes / No). Not marking this column may render the bid non-compliant. - Provide the specification/details of the goods offered in column D, "Offered Technical Specifications", and indicate in Column E "Support for Technical Compliance" where this can be corroborated in the support documents. Also use this column to indicate any deviation from the minimum requirements. - Bidders may add additional lines at the end of the table if they wish to offer other non-listed optional items.
Lot Category Capacity / lift height / operating range Offered
1 Electric Counterbalance Forklift, Light Duty (1 - 1.8 ton) Lifting capacity 1.0 to 1.8 ton, standard lift min 3.0 m
2 Electric Counterbalance Forklift, Medium Duty (1.8 - 2.5 ton) Lifting capacity 1.8 to 2.5 ton, standard lift min 4.5 m
3 Electric Counterbalance Forklift, Heavy Duty (2.5 - 3.5 ton) Lifting capacity 2.5 to 3.5 ton, standard lift min 4.5 m
4 Electric Reach Truck, Standard Reach Lifting capacity 1.4 to 1.8 ton, operating range 7.5 to 10.0 m
5 Electric Reach Truck, High Reach Lifting capacity min 1.6 ton, operating range 10.0 to 12.5 m
6 Electric Reach Truck, Articulated ("Bendi"-type) Lifting capacity 2.0 ton, operating range 7.5 to 12.4 m
7 VNA Machine, Very Narrow Aisle (Man-Up) Lifting capacity 1.0 to 1.5 ton, lift height up to 13.8 m
8 Electric Pallet Truck, Low Lift – Walkie Lifting capacity 1.4 to 2.5 ton, horizontal transport
9 Electric Pallet Truck, Low Lift – Rider Lifting capacity 2.5 to 3.5 ton, horizontal transport
10 Electric Pallet Truck / Stacker, High Lift – Walkie Stacker Lifting capacity 1.0 to 1.6 ton, stacking up to 4.5 m
11 Manual Pallet Jack Lifting capacity min 3 ton, fork height range approx. 85 to 200 mm
12 Electric Order Picker, Low Level Lifting capacity 1.0 ton, platform elevation max 2.0 m
13 Electric Order Picker, Medium Level Lifting capacity 1.0 ton, platform elevation max 6.0 m
14 Electric Order Picker, High Level – Man Up Lifting capacity 1.0 ton, platform elevation max 10.0 m
15 Tow Tractor, Light Duty Tow Towing capacity 1.5 to 3.0 ton, horizontal transport
16 Tow Tractor, Medium Duty Tow Towing capacity 3.0 ton, horizontal transport
17 Trailers / Carts (towed equipment) Different type and capacity trolleys
18 Electric Utility/Pick-up Vehicle, Light Utility Payload capacity 0.4 to 0.7 ton, horizontal transport
19 Electric Utility/Pick-up Vehicle, Medium Utility Payload capacity min 0.7 ton, horizontal transport
UNOPS eMHE Tender — Bidder Document Verification Checklist (Lots 1 to 19)
Document ID Category Document Description Standard / Regulation Applicable Lots Requirement Type Verification Criteria Lot 1 Lot 2 Lot 3 Lot 4 Lot 5 Lot 6 Lot 7 Lot 8 Lot 9 Lot 10 Lot 11 Lot 12 Lot 13 Lot 14 Lot 15 Lot 16 Lot 17 Lot 18 Lot 19 Attached Count
DOC-01 Form E: Manufacturer’s Authorization Form Manufacturer's Authorization Form (MAF) UNOPS Tender Requirement Lots 1 – 19 (All Lots) Mandatory Required if bidder is not the equipment manufacturer. Must be signed and stamped on manufacturer official letterhead. FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE 0
DOC-02 Technical Documentation Manufacturer Technical Datasheets & Product Catalogues OEM Technical Specifications Lots 1 – 19 (All Lots) Mandatory Comprehensive manufacturer technical datasheets and product catalogues detailing full technical specifications, dimensions, performance ratings, and compliance for all offered models. FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE 0
DOC-03 Technical Documentation Battery Charger Specification & Pre-Installation Sheet IEC 61851 / CE Electrical Standards Lots 1 – 10, 12 – 16, 18, 19 Mandatory Technical datasheet of industrial smart charger including input voltage/phase, output profile, plug type, and electrical/ventilation pre-installation requirements. FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE 0
DOC-04 Technical Documentation Drive & Lift Motor Duty Rating Specification Sheets IEC 60034-1 (S2 short-time / S3 intermittent) Lots 1 – 10, 12 – 16, 18, 19 Mandatory Manufacturer published specification sheet stating motor ratings (kW) on S2 (60 min) for drive and S3 (% cyclic factor) for lift. FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE 0
DOC-05 Technical Documentation Cold Chain Storage Configuration Compliance Documentation Operation down to -20°C (Anti-condensation, BMS heater) Lots 1 – 10, 12 – 16, 18, 19 Optional Specification sheet verifying low-temp oil, seals, cabin heating, and battery self-heating for units quoted with cold storage option. FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE 0
DOC-06 Battery & Performance Battery Cycle Life Test Report IEC 62620 (or accredited third-party equivalent) Lots 1 – 10, 12 – 16, 18, 19 Mandatory Verifies min 6,000 cycles at 80% DoD and >=80% retained capacity at 25°C, 1C rate. Required before delivery acceptance. FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE 0
DOC-07 Battery & Performance Battery Management System (BMS) Compliance Certificate IEC 62619 Lots 1 – 10, 12 – 16, 18, 19 Mandatory Documentation confirming BMS complies with IEC 62619 and logs cycle count, depth of discharge, and state of health. FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE 0
DOC-08 Battery & Performance Lithium Battery Transport Safety Test Report / Summary UN 38.3 (UN Manual of Tests and Criteria) Lots 1 – 10, 12 – 16, 18, 19 Mandatory Test report summary confirming compliance with UN 38.3 transport safety regulations for Li-ion / LFP batteries. FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE 0
DOC-09 Battery & Performance Battery Manufacturer Technical Datasheet & Pack Label LiFePO4 Chemistry & kWh Rating Lots 1 – 10, 12 – 16, 18, 19 Mandatory Manufacturer datasheet or pack label stating capacity (kWh), LFP chemistry, cycle count, weight, and extraction method. FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE 0
DOC-10 Battery & Performance Battery End-of-Life & Recycling Protocol Documentation Hazardous Waste Regulations / Take-back Lots 1 – 10, 12 – 16, 18, 19 Mandatory Clear procedures for safe disposal and recycling at end-of-life compliant with local and international hazardous waste regulations. FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE 0
DOC-11 Safety & Compliance Standards CE Marking Certificate / Declaration of Conformity CE / Machinery Directive 2006/42/EC Lots 1 – 16, 18, 19 Mandatory Official Declaration of Conformity or CE certificate confirming equipment meets applicable European safety directives. FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE 0
DOC-12 Safety & Compliance Standards Industrial Truck Safety Standard Compliance Certificate ISO 3691 series / ANSI ITSDF B56 (ISO 3691-5 for Lot 11) Lots 1 – 16, 18, 19 (Lot 11: ISO 3691-5) Mandatory Certification or manufacturer confirmation of compliance with ISO 3691 or recognised equivalent industrial truck safety standards. FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE 0
DOC-13 QMS Quality Management System (QMS) Certificate ISO 9001 (or equivalent) Lots 1 – 19 (All Lots) Mandatory Must be issued in the name of the manufacturer by an independent accredited certification body. If the legal manufacturer and the OEM / manufacturing facility are different entities, certificates must be provided for both. Valid at submission. FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE 0
DOC-14 EMS Environmental Management System (EMS) Certificate or Policy ISO 14001:2015 (or equivalent / policy) Lots 1 – 19 (All Lots) Mandatory Certificate from accredited body or internal environmental policy document issued by the manufacturer. If the legal manufacturer and the OEM / manufacturing facility are different entities, documentation covering the actual OEM manufacturing facility (or both) must be provided. FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE 0
DOC-15 Warranty & After-Sales Support Machinery & Accessories Base Warranty Certificate Min 1 Year / 1,500 Operating Hours Lots 1 – 19 (All Lots) Mandatory Certificate confirming minimum 1-year / 1,500-hour warranty commencing on successful completion of acceptance inspections. FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE 0
DOC-16 Warranty & After-Sales Support Spare Parts & Consumables Catalogue OEM Parts Standard (2-Year Spares) Lots 1 – 19 (All Lots) Optional Comprehensive spare parts catalog with OEM part numbers, descriptions, pricing schedule, and recommended 2-year maintenance spares list. FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE 0
DOC-17 Warranty & After-Sales Support Traction Battery Extended Warranty Certificate Min 6 Years Manufacturer Warranty Lots 1 – 10, 12 – 16, 18, 19 Mandatory Official certificate confirming minimum 6-year warranty on the lithium battery commencing upon delivery acceptance. FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE 0
DOC-18 Form F: Commercialization Capability Authorized Distributor & Service Network List Africa (min 5 countries), Asia (min 3 countries) Lots 1 – 19 (All Lots) Mandatory List of distributors with contact details providing full warranty and repair support in required regions. Failure to provide excludes bid. FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE 0
DOC-19 Documentation & Manuals Owner / Operator User Instruction Manual Multilingual (EN, FR, ES, or AR) Lots 1 – 19 (All Lots) Mandatory Comprehensive user manual in the destination country official language (English, French, Spanish, or Arabic). FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE 0
DOC-20 Documentation & Manuals Workshop, Service & Technical Repair Manual Multilingual (EN, FR, ES, or AR) Lots 1 – 19 (All Lots) Optional Detailed technical repair, maintenance, and workshop service documentation provided in required project languages. FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE 0
UNOPS eMHE Tender — Document Naming Conventions & Submission Guidelines
Rule / Item Guideline & Requirement Standard Format, Syntax & Examples
File Naming Syntax Mandatory naming pattern for all bid documentation [BidderName]_[Lot#]_[DocID]_[DocumentTitle].pdf (e.g., ABCMotors_Lot02_DOC-06_CycleLifeReport.pdf)
File Format Permitted document formats for electronic submission PDF only (Searchable / OCR text preferred; unencrypted; max 25 MB per attachment)
Cross-Lot Documents Submissions valid across all or multiple quoted lots Use 'LotALL' in filename (e.g., ABCMotors_LotALL_DOC-03_ISO9001.pdf) and check corresponding lot boxes above
Test Reports & Standards IEC, UN 38.3, and CE compliance documentation Must be issued by independent ISO/IEC 17025 accredited laboratory and show complete test summary parameters
Warranties & Support Base equipment warranty and extended lithium battery warranty Signed OEM certificates guaranteeing min 1 yr/1500 hrs equipment and min 6 yrs traction battery coverage
Verification Matrix How to complete the Lot 1–19 matrix in rows 7–26 Mark [X] in each lot column for each document included in the bid package; Attached Count auto-calculates
Lot 1: Electric Counterbalance Forklift, Light Duty (1 - 1.8 ton)
Lifting capacity 1.0 to 1.8 ton, standard lift min 3.0 m
Name and physical address of actual Manufacturing site(s):
Country of origin:
Product Website:
Item UNOPS Minimum Technical Requirement Complies (Yes / No) Offered Technical Specifications Provide a clear description of the corresponding characteristic of the offered Goods Support for Technical Compliance (Provide document title, catalog/datasheet reference, and page number)
1 Propellant, electric.
2 Lifting capacity, ton, between 1.0 and 1.8.
3 Standard lift, to underside of forks, min 3 m.
4 Working aisle width, mm, max 4,000. Measured as the narrowest aisle in which the truck can turn and stack a 1000 x 1200 mm pallet handled crossways, including 200 mm total operating clearance. Bidder to state the figure for the mast, tyre and fork configuration actually offered.
5 Turning radius, mm, max 2,000. Measured from the centre of rotation to the outermost point of the truck with the steering at full lock.
6 Retracted mast height, mm, max 2,300: overall height of the mast with the forks fully lowered, for the lift height offered. Bidder to state, for the offered mast, the retracted mast height, the free lift (height the forks rise before the mast begins to extend) and the extended mast height with the forks fully raised.
7 Configuration: 3-wheel or 4-wheel chassis; bidder to specify.
8 Battery type: Lithium Iron Phosphate (Li-ion / LFP). Other lithium chemistries (NMC, NCA, LTO) and lead-acid batteries are not acceptable.
9 Battery capacity, kWh, min 25
10 Battery charger: wall-mounted AC charger, single-phase 220 to 240 V 50 Hz, maximum AC input current 32 A, rated output approx. 6.0 to 6.6 kW, supplied, fitted and commissioned by the supplier, with all required cables, ready for connection to the local AC electrical grid by a qualified electrician. Bidder to state supported input voltage, phase, frequency and current draw per unit, and the total simultaneous charging load for the quantity offered.
11 Electric protection, min IP54.
12 Battery charge indicator.
13 Operation hour meter.
14 Key or pin-code access system.
15 Driver position, seated or stand-on; bidder to specify.
16 Safety overhead operator protection (open overhead guard).
17 Tyres, pneumatic or solid, suitable for tarmac, concrete, or other solid warehouse floor surfaces. Must be non-marking to comply with Good Manufacturing Practice standards in medical/pharmaceutical warehouses.
18 Power steering.
19 Drive motor rating at short-time duty S2, 60 minutes (IEC 60034-1), kW, min 4.5 per drive motor and min 9.0 total installed drive power. Bidder to state the duty type and rating period on which each motor power is quoted, supported by the manufacturer's published technical specification sheet. Where a rating other than the one specified is quoted, the equivalent value on the specified duty basis shall be stated.
20 Lift motor rating at S3 per IEC 60034-1, kW, min 10.0; bidder to state the cyclic duration factor (e.g. S3 15%).
21 Travel speed, laden/unladen, km/h, min 10/12.
22 Max. gradeability, laden, %, min 10.
23 Brakes, hydraulic/hydrostatic or electric.
24 Parking brake.
25 Lifting control, hydraulic or electric.
26 Tilt of mast, forward/reverse suitable for safe loading/unloading, degrees, min 3/6
27 Working lights, front and rear.
28 1 kg fire extinguisher, min.
29 First aid box.
30 Battery cycle life, min 6,000 cycles at 80% depth of discharge (DoD), measured to an end-of-life criterion of 80% retained rated capacity, at 25 degrees C ambient and 1C charge/discharge rate. Bidder to submit the battery manufacturer's datasheet or pack label stating the cycle count. Where the datasheet does not state depth of discharge and end-of-life retention, the bidder shall confirm both in writing on manufacturer letterhead. A cycle life test report referencing IEC 62620 (or accredited third-party equivalent) shall be provided before delivery acceptance.
31 Battery management system (BMS) compliant with IEC 62619, logging cycle count, depth of discharge and state of health, retrievable by the operator or service technician.
32 Bidder to state battery weight (kg), removal/extraction method, and whether a lifting aid is required for battery removal and replacement.
33 Ambient operating conditions (base configuration): equipment rated for continuous operation in standard indoor warehouse conditions, ambient 0 degrees C to +40 degrees C. All prices in the main schedule are for this base configuration.
34 Seat belt for the operator, mandatory for seated configuration.
35 Reverse alarm, acoustic, mandatory.
36 Anti-roll-back system preventing roll-back on inclines.
37 Emergency stop button, mandatory, isolating drive and hydraulic power.
38 Hygiene and GMP: Easy-to-clean design (smooth surfaces, minimal exposed wiring) to comply with Good Manufacturing Practice standards in medical/pharmaceutical warehouses.
39 Certifications: Equipment to possess CE marking (or equivalent)
40 Compliance with ISO 3691 (or equivalent recognised industrial truck safety standard, e.g. ANSI/ITSDF B56) required.
41 Certificate of Quality Management System according to ISO 9001 in the name of the manufacturer or equivalent certification. In case of ISO9001 the Certificate must be issued by an independent Certifying Body/Agency. If the legal manufacturer and the OEM / manufacturing facility are different entities, certificates must be provided for both.
42 Manufacturer Environmental management system: ISO 14001:2015 and/or equivalent certification and/or internal policy document issued by the Manufacturer related to environmental considerations of the company. If the legal manufacturer and the OEM / manufacturing facility are different entities, documentation covering the actual OEM manufacturing facility (or both) must be provided.
43 Manufacturer's authorization if the bidder is not the manufacturer
44 Owners/operators manual, English, French, Spanish or Arabic depending on destination country.
45 Battery end-of-life: Bidder to provide documentation on safe disposal/recycling of the battery at end-of-life, compliant with local and international hazardous waste regulations.
46 Warranty: Machinery and all accessories under warranty for a minimum of 1 year or 1,500 hours of operation, whichever occurs first. The warranty period shall commence on the date of successful completion of the relevant tests and/or inspections of the goods by UNOPS or the Consignee designated by UNOPS to the Contractor. A warranty certificate shall be provided with the delivery of the goods
47 Warranty Battery: minimum 6 years. The warranty period shall commence on the date of successful completion of the relevant tests and/or inspections of the goods by UNOPS or the Consignee designated by UNOPS to the Contractor. A warranty certificate shall be provided with the delivery of the goods
48 Bidders shall demonstrate an authorised distributor network with full warranty and after-sales service in at least 5 countries of the Africa region, and minimum 3 countries in Asia. Bidders shall submit a list of distributors with names and contact details. The nominated local distributor shall be responsible for warranty and repair of the base item and all additional equipment provided with each item. Failure to demonstrate the required extent of coverage with full warranty and after-sales service will exclude the bidder from further evaluation.
DESIRABLE OPTIONS, PRICED SEPARATELY: Please enter further available options as applicable. If Standard, state "Standard".
49 Repair manual in one or more of English, Spanish, French, Arabic, please indicate.
50 Rear towing coupling/hitch/hook
51 Electric rotating beacon/flashing beacon.
52 Spare parts kit, 1 year / 1,500 hours of operation, min.
53 Alternative Lithium-ion (Li-ion/LFP) Battery Options (e.g. other capacities in kWh)
54 Battery end-of-life: Manufacturer-supported take-back/recycling programme.
55 Cold chain configuration: Equipment rated for continuous operation in cold storage down to -20°C, comprising: - Anti-condensation protection for electrical and electronic assemblies; - Low-temperature-rated hydraulic oil, cold-rated seals, and cold-store tyres/wheels; - Battery self-heating system with BMS low-temperature charge inhibit; - Enclosed cold-store cabin (where available/applicable for the offered model): glass all around, cabin heating, heated front/rear glass (or de-misting system), wipers, and interior/exterior mirrors; - Operator seat/platform heating where an enclosed cabin is not fitted or not standard. Bidder to state the operating temperature range of camera, monitor, and fork laser where fitted. To be quoted as a separate unit price and not included in the base price.
56 Higher-output charger (e.g. a three-phase 400 V charger) - Bidder to define
57 Extended Warranty for 1 year or 3,000 hours of operation, whichever comes first
58 Extended Warranty for 1 year for the battery
Lot 2: Electric Counterbalance Forklift, Medium Duty (1.8 - 2.5 ton)
Lifting capacity 1.8 to 2.5 ton, standard lift min 4.5 m
Name and physical address of actual Manufacturing site(s):
Country of origin:
Product Website:
Item UNOPS Minimum Technical Requirement Complies (Yes / No) Offered Technical Specifications Support for Technical Compliance (Provide document title, catalog/datasheet reference, and page number)
1 Propellant, electric.
2 Lifting capacity, ton, 1.8 to 2.5.
3 Standard lift, to underside of forks, min 4.5 m
4 Working aisle width, mm, max 4,000. Measured as the narrowest aisle in which the truck can turn and stack a 1000 x 1200 mm pallet handled crossways, including 200 mm total operating clearance. Bidder to state the figure for the mast, tyre and fork configuration actually offered.
5 Turning radius, mm, max 2,100. Measured from the centre of rotation to the outermost point of the truck with the steering at full lock.
6 Retracted mast height, mm, max 3,000: overall height of the mast with the forks fully lowered, for the lift height offered. Bidder to state, for the offered mast, the retracted mast height, the free lift (height the forks rise before the mast begins to extend) and the extended mast height with the forks fully raised.
7 Configuration: 3-wheel or 4-wheel chassis; bidder to specify.
8 Battery type: Lithium Iron Phosphate (Li-ion / LFP). Other lithium chemistries (NMC, NCA, LTO) and lead-acid batteries are not acceptable.
9 Battery capacity, kWh, min 30
10 Battery charger: wall-mounted AC charger, single-phase 220 to 240 V 50 Hz, maximum AC input current 32 A, rated output approx. 6.0 to 6.6 kW, supplied, fitted and commissioned by the supplier, with all required cables, ready for connection to the local AC electrical grid by a qualified electrician. Bidder to state supported input voltage, phase, frequency and current draw per unit, and the total simultaneous charging load for the quantity offered.
11 Electric protection, min IP54.
12 Battery charge indicator.
13 Operation hour meter.
14 Key or pin-code access system.
15 Driver position, seated.
16 Safety overhead operator protection (open overhead guard).
17 Tyres, pneumatic or solid, suitable for tarmac, concrete, or other solid warehouse floor surfaces. Must be non-marking to comply with Good Manufacturing Practice standards in medical/pharmaceutical warehouses.
18 Power steering.
19 Drive motor rating at short-time duty S2, 60 minutes (IEC 60034-1), kW, min 9.0 total installed drive power; bidder to state number of drive motors. Bidder to state the duty type and rating period on which each motor power is quoted, supported by the manufacturer's published technical specification sheet. Where a rating other than the one specified is quoted, the equivalent value on the specified duty basis shall be stated.
20 Lift motor rating at S3 per IEC 60034-1, kW, min 10.0; bidder to state the cyclic duration factor (e.g. S3 15%).
21 Travel speed, laden/unladen, km/h, min 13/15.
22 Max. gradeability, laden/unladen, %, min 12/18.
23 Brakes, hydraulic/hydrostatic or electric.
24 Parking brake.
25 Lifting control, hydraulic or electric.
26 Tilt of mast, forward/reverse suitable for safe loading/unloading, degrees, min 5/8.
27 Working lights, front and rear.
28 1 kg fire extinguisher, min.
29 First aid box.
30 Battery cycle life, min 6,000 cycles at 80% depth of discharge (DoD), measured to an end-of-life criterion of 80% retained rated capacity, at 25 degrees C ambient and 1C charge/discharge rate. Bidder to submit the battery manufacturer's datasheet or pack label stating the cycle count. Where the datasheet does not state depth of discharge and end-of-life retention, the bidder shall confirm both in writing on manufacturer letterhead. A cycle life test report referencing IEC 62620 (or accredited third-party equivalent) shall be provided before delivery acceptance.
31 Battery management system (BMS) compliant with IEC 62619, logging cycle count, depth of discharge and state of health, retrievable by the operator or service technician.
32 Bidder to state battery weight (kg), removal/extraction method, and whether a lifting aid is required for battery removal and replacement.
33 Ambient operating conditions (base configuration): equipment rated for continuous operation in standard indoor warehouse conditions, ambient 0 degrees C to +40 degrees C. All prices in the main schedule are for this base configuration.
34 Seat belt for the operator, mandatory.
35 Reverse alarm, acoustic, mandatory.
36 Anti-roll-back system preventing roll-back on inclines.
37 Emergency stop button, mandatory, isolating drive and hydraulic power.
38 Hygiene and GMP: Easy-to-clean design (smooth surfaces, minimal exposed wiring) to comply with Good Manufacturing Practice standards in medical/pharmaceutical warehouses.
39 Certifications: Equipment to possess CE marking (or equivalent)
40 Compliance with ISO 3691 (or equivalent recognised industrial truck safety standard, e.g. ANSI/ITSDF B56) required.
41 Certificate of Quality Management System according to ISO 9001 in the name of the manufacturer or equivalent certification. In case of ISO9001 the Certificate must be issued by an independent Certifying Body/Agency. If the legal manufacturer and the OEM / manufacturing facility are different entities, certificates must be provided for both.
42 Manufacturer Environmental management system: ISO 14001:2015 and/or equivalent certification and/or internal policy document issued by the Manufacturer related to environmental considerations of the company. If the legal manufacturer and the OEM / manufacturing facility are different entities, documentation covering the actual OEM manufacturing facility (or both) must be provided.
43 Manufacturer's authorization if the bidder is not the manufacturer
44 Owners/operators manual, English, French, Spanish or Arabic depending on destination country.
45 Battery end-of-life: Bidder to provide documentation on safe disposal/recycling of the battery at end-of-life, compliant with local and international hazardous waste regulations.
46 Warranty: Machinery and all accessories under warranty for a minimum of 1 year or 1,500 hours of operation, whichever occurs first. The warranty period shall commence on the date of successful completion of the relevant tests and/or inspections of the goods by UNOPS or the Consignee designated by UNOPS to the Contractor. A warranty certificate shall be provided with the delivery of the goods
47 Warranty Battery: minimum 6 years. The warranty period shall commence on the date of successful completion of the relevant tests and/or inspections of the goods by UNOPS or the Consignee designated by UNOPS to the Contractor. A warranty certificate shall be provided with the delivery of the goods
48 Bidders shall demonstrate an authorised distributor network with full warranty and after-sales service in at least 5 countries of the Africa region, and minimum 3 countries in Asia. Bidders shall submit a list of distributors with names and contact details. The nominated local distributor shall be responsible for warranty and repair of the base item and all additional equipment provided with each item. Failure to demonstrate the required extent of coverage with full warranty and after-sales service will exclude the bidder from further evaluation.
DESIRABLE OPTIONS, PRICED SEPARATELY: Please enter further available options as applicable. If Standard, state "Standard".
49 Repair manual in one or more of English, Spanish, French, Arabic, please indicate.
50 Rear towing coupling/hitch/hook
51 Electric rotating beacon/flashing beacon.
52 Spare parts kit, 1 year / 1,500 hours of operation, min.
53 Alternative Lithium-ion (Li-ion/LFP) Battery Options (e.g. other capacities in kWh)
54 Battery end-of-life: Manufacturer-supported take-back/recycling programme.
55 Cold chain configuration: Equipment rated for continuous operation in cold storage down to -20°C, comprising: - Anti-condensation protection for electrical and electronic assemblies; - Low-temperature-rated hydraulic oil, cold-rated seals, and cold-store tyres/wheels; - Battery self-heating system with BMS low-temperature charge inhibit; - Enclosed cold-store cabin (where available/applicable for the offered model): glass all around, cabin heating, heated front/rear glass (or de-misting system), wipers, and interior/exterior mirrors; - Operator seat/platform heating where an enclosed cabin is not fitted or not standard. Bidder to state the operating temperature range of camera, monitor, and fork laser where fitted. To be quoted as a separate unit price and not included in the base price.
56 Higher-output charger (e.g. a three-phase 400 V charger) - Bidder to define
57 Extended Warranty for 1 year or 3,000 hours of operation, whichever comes first
58 Extended Warranty for 1 year for the battery
Lot 3: Electric Counterbalance Forklift, Heavy Duty (2.5 - 3.5 ton)
Lifting capacity 2.5 to 3.5 ton, standard lift min 4.5 m
Name and physical address of actual Manufacturing site(s):
Country of origin:
Product Website:
Item UNOPS Minimum Technical Requirement Complies (Yes / No) Offered Technical Specifications Support for Technical Compliance
1 Propellant, electric.
2 Lifting capacity, ton, 2.5 to 3.5.
3 Standard lift, to underside of forks, min 4.5 m
4 Working aisle width, mm, max 4,300. Measured as the narrowest aisle in which the truck can turn and stack a 1000 x 1200 mm pallet handled crossways, including 200 mm total operating clearance. Bidder to state the figure for the mast, tyre and fork configuration actually offered.
5 Turning radius, mm, max 2,250. Measured from the centre of rotation to the outermost point of the truck with the steering at full lock.
6 Retracted mast height, mm, max 3,000: overall height of the mast with the forks fully lowered, for the lift height offered. Bidder to state, for the offered mast, the retracted mast height, the free lift (height the forks rise before the mast begins to extend) and the extended mast height with the forks fully raised.
7 Battery type: Lithium Iron Phosphate (Li-ion / LFP). Other lithium chemistries (NMC, NCA, LTO) and lead-acid batteries are not acceptable.
8 Battery capacity, kWh, min 36
9 Battery charger: wall-mounted AC charger, single-phase 220 to 240 V 50 Hz, maximum AC input current 32 A, rated output approx. 6.0 to 6.6 kW, supplied, fitted and commissioned by the supplier, with all required cables, ready for connection to the local AC electrical grid by a qualified electrician. Bidder to state supported input voltage, phase, frequency and current draw per unit, and the total simultaneous charging load for the quantity offered.
10 Electric protection, min IP54.
11 Battery charge indicator.
12 Operation hour meter.
13 Key or pin-code access system.
14 Driver position, seated.
15 Open cabin with safety overhead operator protection.
16 2 axles and min 4 wheels.
17 Tyres, pneumatic or solid, suitable for tarmac, concrete, or other solid warehouse floor surfaces. Must be non-marking to comply with Good Manufacturing Practice standards in medical/pharmaceutical warehouses.
18 Power steering.
19 Tilt of mast, forward/reverse, degree, min 5/10.
20 Drive motor rating at short-time duty S2, 60 minutes (IEC 60034-1), kW, min 15.0 total installed drive power; bidder to state number of drive motors. Bidder to state the duty type and rating period on which each motor power is quoted, supported by the manufacturer's published technical specification sheet. Where a rating other than the one specified is quoted, the equivalent value on the specified duty basis shall be stated.
21 Lift motor rating at S3 per IEC 60034-1, kW, min 17.0; bidder to state the cyclic duration factor (e.g. S3 15%).
22 Travel speed, laden/unladen, km/h, min 15/17
23 Max. gradeability, laden/unladen, % min 17/25.
24 Brakes, hydraulic/hydrostatic or electric.
25 Parking brake.
26 Lifting control, hydraulic or electric.
27 Rear towing coupling/hitch/hook.
28 Working lights, front and rear.
29 Stop lights and directional indicators, rear, min.
30 1 kg fire extinguisher, min.
31 First aid box.
32 Battery cycle life, min 6,000 cycles at 80% depth of discharge (DoD), measured to an end-of-life criterion of 80% retained rated capacity, at 25 degrees C ambient and 1C charge/discharge rate. Bidder to submit the battery manufacturer's datasheet or pack label stating the cycle count. Where the datasheet does not state depth of discharge and end-of-life retention, the bidder shall confirm both in writing on manufacturer letterhead. A cycle life test report referencing IEC 62620 (or accredited third-party equivalent) shall be provided before delivery acceptance.
33 Battery management system (BMS) compliant with IEC 62619, logging cycle count, depth of discharge and state of health, retrievable by the operator or service technician.
34 Bidder to state battery weight (kg), removal/extraction method, and whether a lifting aid is required for battery removal and replacement.
35 Ambient operating conditions (base configuration): equipment rated for continuous operation in standard indoor warehouse conditions, ambient 0 degrees C to +40 degrees C. All prices in the main schedule are for this base configuration.
36 Seat belt for the operator, mandatory.
37 Reverse alarm, acoustic, mandatory.
38 Anti-roll-back system preventing roll-back on inclines.
39 Emergency stop button, mandatory, isolating drive and hydraulic power.
40 Hygiene and GMP: Easy-to-clean design (smooth surfaces, minimal exposed wiring) to comply with Good Manufacturing Practice standards in medical/pharmaceutical warehouses.
41 Certifications: Equipment to possess CE marking (or equivalent)
42 Compliance with ISO 3691 (or equivalent recognised industrial truck safety standard, e.g. ANSI/ITSDF B56) required.
43 Certificate of Quality Management System according to ISO 9001 in the name of the manufacturer or equivalent certification. In case of ISO9001 the Certificate must be issued by an independent Certifying Body/Agency. If the legal manufacturer and the OEM / manufacturing facility are different entities, certificates must be provided for both.
44 Manufacturer Environmental management system: ISO 14001:2015 and/or equivalent certification and/or internal policy document issued by the Manufacturer related to environmental considerations of the company. If the legal manufacturer and the OEM / manufacturing facility are different entities, documentation covering the actual OEM manufacturing facility (or both) must be provided.
45 Manufacturer's authorization if the bidder is not the manufacturer
46 Owners/operators manual, English, French, Spanish or Arabic depending on destination country.
47 Battery end-of-life: Bidder to provide documentation on safe disposal/recycling of the battery at end-of-life, compliant with local and international hazardous waste regulations.
48 Warranty: Machinery and all accessories under warranty for a minimum of 1 year or 1,500 hours of operation, whichever occurs first. The warranty period shall commence on the date of successful completion of the relevant tests and/or inspections of the goods by UNOPS or the Consignee designated by UNOPS to the Contractor. A warranty certificate shall be provided with the delivery of the goods
49 Warranty Battery: minimum 6 years. The warranty period shall commence on the date of successful completion of the relevant tests and/or inspections of the goods by UNOPS or the Consignee designated by UNOPS to the Contractor. A warranty certificate shall be provided with the delivery of the goods
50 Bidders shall demonstrate an authorised distributor network with full warranty and after-sales service in at least 5 countries of the Africa region, and minimum 3 countries in Asia. Bidders shall submit a list of distributors with names and contact details. The nominated local distributor shall be responsible for warranty and repair of the base item and all additional equipment provided with each item. Failure to demonstrate the required extent of coverage with full warranty and after-sales service will exclude the bidder from further evaluation.
DESIRABLE OPTIONS, PRICED SEPARATELY: Please enter further available options as applicable. If Standard, state "Standard".
51 Repair manual in one or more of English, Spanish, French, Arabic, please indicate.
52 Electric rotating beacon/flashing beacon.
53 Spare parts kit, 1 year / 1,500 hours of operation, min.
54 Alternative Lithium-ion (Li-ion/LFP) Battery Options (e.g. other capacities in kWh)
55 Battery end-of-life: Manufacturer-supported take-back/recycling programme.
56 Cold chain configuration: Equipment rated for continuous operation in cold storage down to -20°C, comprising: - Anti-condensation protection for electrical and electronic assemblies; - Low-temperature-rated hydraulic oil, cold-rated seals, and cold-store tyres/wheels; - Battery self-heating system with BMS low-temperature charge inhibit; - Enclosed cold-store cabin (where available/applicable for the offered model): glass all around, cabin heating, heated front/rear glass (or de-misting system), wipers, and interior/exterior mirrors; - Operator seat/platform heating where an enclosed cabin is not fitted or not standard. Bidder to state the operating temperature range of camera, monitor, and fork laser where fitted. To be quoted as a separate unit price and not included in the base price.
57 Higher-output charger (e.g. a three-phase 400 V charger) - Bidder to define
58 Extended Warranty for 1 year or 3,000 hours of operation, whichever comes first
59 Extended Warranty for 1 year for the battery
Lot 4: Electric Reach Truck, Standard Reach
Lifting capacity 1.4 to 1.8 ton, operating range 7.5 to 10.0 m
Name and physical address of actual Manufacturing site(s):
Country of origin:
Product Website:
Item UNOPS Minimum Technical Requirement Complies (Yes / No) Offered Technical Specifications Support for Technical Compliance
1 Propellant, electric.
2 Lifting capacity, ton, 1.4 to 1.8.
3 Standard lift min 7.5 m
4 Mast type: duplex or triplex, free-lift; bidder to specify.
5 Working aisle width, mm, max 3,000. Measured as the narrowest aisle in which the truck can turn and stack a 1000 x 1200 mm pallet handled crossways, including 200 mm total operating clearance. Bidder to state the figure for the mast, tyre and fork configuration actually offered.
6 Turning radius, mm, max 1,750. Measured from the centre of rotation to the outermost point of the truck with the steering at full lock.
7 Retracted mast height, mm, max 3,900: overall height of the mast with the forks fully lowered, for the lift height offered. Bidder to state, for the offered mast, the retracted mast height, the free lift (height the forks rise before the mast begins to extend) and the extended mast height with the forks fully raised.
8 Reach mechanism: pantograph or moving-mast; bidder to specify.
9 Battery type: Lithium Iron Phosphate (Li-ion / LFP). Other lithium chemistries (NMC, NCA, LTO) and lead-acid batteries are not acceptable.
10 Battery capacity, kWh, min 26.8
11 Battery charger: wall-mounted AC charger, single-phase 220 to 240 V 50 Hz, maximum AC input current 32 A, rated output approx. 6.0 to 6.6 kW, supplied, fitted and commissioned by the supplier, with all required cables, ready for connection to the local AC electrical grid by a qualified electrician. Bidder to state supported input voltage, phase, frequency and current draw per unit, and the total simultaneous charging load for the quantity offered.
12 Electric protection, min IP54.
13 Battery charge indicator.
14 Operation hour meter.
15 Operator position: stand-in or seated; bidder to specify.
16 Overhead guard for operator protection.
17 Drive motor rating at short-time duty S2, 60 minutes (IEC 60034-1), kW, min 6. Bidder to state the duty type and rating period on which each motor power is quoted, supported by the manufacturer's published technical specification sheet. Where a rating other than the one specified is quoted, the equivalent value on the specified duty basis shall be stated.
18 Lift motor rating at S3 per IEC 60034-1, kW, min 14; bidder to state the cyclic duration factor.
19 Travel speed, laden/unladen, km/h, min 8/10.
20 Lift speed, laden, m/s, bidder to state.
21 Max. gradeability, laden, %, min 7.
22 Brakes, appropriate for equipment type (hydraulic/hydrostatic/electric) with regenerative braking on descent/deceleration.
23 Parking brake.
24 Load wheels: non-marking polyurethane.
25 Load Sensing/Stability Control system, active at height (bidder to describe).
26 Battery cycle life, min 6,000 cycles at 80% depth of discharge (DoD), measured to an end-of-life criterion of 80% retained rated capacity, at 25 degrees C ambient and 1C charge/discharge rate. Bidder to submit the battery manufacturer's datasheet or pack label stating the cycle count. Where the datasheet does not state depth of discharge and end-of-life retention, the bidder shall confirm both in writing on manufacturer letterhead. A cycle life test report referencing IEC 62620 (or accredited third-party equivalent) shall be provided before delivery acceptance.
27 Battery management system (BMS) compliant with IEC 62619, logging cycle count, depth of discharge and state of health, retrievable by the operator or service technician.
28 Bidder to state battery weight (kg), removal/extraction method, and whether a lifting aid is required for battery removal and replacement.
29 Ambient operating conditions (base configuration): equipment rated for continuous operation in standard indoor warehouse conditions, ambient 0 degrees C to +40 degrees C. All prices in the main schedule are for this base configuration.
30 Seat belt, mandatory for seated configuration.
31 Reverse alarm, acoustic, mandatory.
32 Anti-roll-back system preventing roll-back on inclines.
33 Emergency stop button, mandatory, isolating drive and hydraulic power.
34 Key or pin-code access system for operator authorisation.
35 1 kg fire extinguisher, min.
36 LED floor warning spotlight projecting a red or blue spot onto the floor ahead of or behind the machine to warn pedestrians and oncoming equipment.
37 Camera and monitor assistance for high-level fork placement, mandatory. Bidder to state camera resolution, monitor screen size, mounting position, ingress protection rating and operating temperature range of both camera and monitor.
38 Fork position laser: adjustable fan-shaped beam projected from the forks indicating the exact fork position, red or green; stainless steel housing; min IP67; IK10 shock resistance; line accuracy plus/minus 0.05 mm.
39 Fork height and tilt indicator with digital readout of fork height and mast tilt condition, visible from the operator position.
40 Hygiene and GMP: Easy-to-clean design (smooth surfaces, minimal exposed wiring) to comply with Good Manufacturing Practice standards in medical/pharmaceutical warehouses.
41 Certifications: Equipment to possess CE marking (or equivalent)
42 Compliance with ISO 3691 (or equivalent recognised industrial truck safety standard, e.g. ANSI/ITSDF B56) required.
43 Certificate of Quality Management System according to ISO 9001 in the name of the manufacturer or equivalent certification. In case of ISO9001 the Certificate must be issued by an independent Certifying Body/Agency. If the legal manufacturer and the OEM / manufacturing facility are different entities, certificates must be provided for both.
44 Manufacturer Environmental management system: ISO 14001:2015 and/or equivalent certification and/or internal policy document issued by the Manufacturer related to environmental considerations of the company. If the legal manufacturer and the OEM / manufacturing facility are different entities, documentation covering the actual OEM manufacturing facility (or both) must be provided.
45 Manufacturer's authorization if the bidder is not the manufacturer
46 Owners/operators manual, English, French, Spanish or Arabic depending on destination country.
47 Battery end-of-life: Bidder to provide documentation on safe disposal/recycling of the battery at end-of-life, compliant with local and international hazardous waste regulations.
48 Warranty: Machinery and all accessories under warranty for a minimum of 1 year or 1,500 hours of operation, whichever occurs first. The warranty period shall commence on the date of successful completion of the relevant tests and/or inspections of the goods by UNOPS or the Consignee designated by UNOPS to the Contractor. A warranty certificate shall be provided with the delivery of the goods
49 Warranty Battery: minimum 6 years. The warranty period shall commence on the date of successful completion of the relevant tests and/or inspections of the goods by UNOPS or the Consignee designated by UNOPS to the Contractor. A warranty certificate shall be provided with the delivery of the goods
50 Bidders shall demonstrate an authorised distributor network with full warranty and after-sales service in at least 5 countries of the Africa region, and minimum 3 countries in Asia. Bidders shall submit a list of distributors with names and contact details. The nominated local distributor shall be responsible for warranty and repair of the base item and all additional equipment provided with each item. Failure to demonstrate the required extent of coverage with full warranty and after-sales service will exclude the bidder from further evaluation.
DESIRABLE OPTIONS, PRICED SEPARATELY: Please enter further available options as applicable. If Standard, state "Standard".
51 Repair manual in one or more of English, Spanish, French, Arabic, please indicate.
52 Electric rotating beacon/flashing beacon.
53 Spare parts kit, 1 year / 1,500 hours of operation, min.
54 Alternative Lithium-ion (Li-ion/LFP) Battery Options (e.g. other capacities in kWh)
55 Battery end-of-life: Manufacturer-supported take-back/recycling programme.
56 Cold chain configuration: Equipment rated for continuous operation in cold storage down to -20°C, comprising: - Anti-condensation protection for electrical and electronic assemblies; - Low-temperature-rated hydraulic oil, cold-rated seals, and cold-store tyres/wheels; - Battery self-heating system with BMS low-temperature charge inhibit; - Enclosed cold-store cabin (where available/applicable for the offered model): glass all around, cabin heating, heated front/rear glass (or de-misting system), wipers, and interior/exterior mirrors; - Operator seat/platform heating where an enclosed cabin is not fitted or not standard. Bidder to state the operating temperature range of camera, monitor, and fork laser where fitted. To be quoted as a separate unit price and not included in the base price.
57 Higher-output charger (e.g. a three-phase 400 V charger) - Bidder to define
58 Extended Warranty for 1 year or 3,000 hours of operation, whichever comes first
59 Extended Warranty for 1 year for the battery
Lot 5: Electric Reach Truck, High Reach
Lifting capacity min 1.6 ton, operating range 10.0 to 12.5 m
Name and physical address of actual Manufacturing site(s):
Country of origin:
Product Website:
Item UNOPS Minimum Technical Requirement Complies (Yes / No) Offered Technical Specifications Support for Technical Compliance
1 Propellant, electric.
2 Lifting capacity, ton, min 1.6
3 Standard lift min 10.0 m
4 Mast type: bidder to specify.
5 Working aisle width, mm, max 3,000. Measured as the narrowest aisle in which the truck can turn and stack a 1000 x 1200 mm pallet handled crossways, including 200 mm total operating clearance. Bidder to state the figure for the mast, tyre and fork configuration actually offered.
6 Turning radius, mm, max 1,950. Measured from the centre of rotation to the outermost point of the truck with the steering at full lock.
7 Retracted mast height, mm, max 4,900: overall height of the mast with the forks fully lowered, for the lift height offered. Bidder to state, for the offered mast, the retracted mast height, the free lift (height the forks rise before the mast begins to extend) and the extended mast height with the forks fully raised.
8 Battery type: Lithium Iron Phosphate (Li-ion / LFP). Other lithium chemistries (NMC, NCA, LTO) and lead-acid batteries are not acceptable.
9 Battery capacity, kWh, min 40
10 Battery charger: wall-mounted AC charger, single-phase 220 to 240 V 50 Hz, maximum AC input current 32 A, rated output approx. 6.0 to 6.6 kW, supplied, fitted and commissioned by the supplier, with all required cables, ready for connection to the local AC electrical grid by a qualified electrician. Bidder to state supported input voltage, phase, frequency and current draw per unit, and the total simultaneous charging load for the quantity offered.
11 Electric protection, min IP54.
12 Battery charge indicator.
13 Operation hour meter.
14 Operator position: stand-in or seated; bidder to specify.
15 Overhead guard for operator protection.
16 Drive motor rating at short-time duty S2, 60 minutes (IEC 60034-1), kW, min 6.5. Bidder to state the duty type and rating period on which each motor power is quoted, supported by the manufacturer's published technical specification sheet. Where a rating other than the one specified is quoted, the equivalent value on the specified duty basis shall be stated.
17 Lift motor rating at S3 per IEC 60034-1, kW, min 14; bidder to state the cyclic duration factor.
18 Travel speed, laden/unladen, km/h, min 12/12.
19 Lift speed, laden, m/s, bidder to state.
20 Max. gradeability, laden, %, min 10.
21 Brakes, appropriate for equipment type, with regenerative braking on descent/deceleration.
22 Parking brake.
23 Load wheels: non-marking polyurethane.
24 Load Sensing/Stability Control system, mandatory at this lift height (mast-sway compensation, residual-capacity display); bidder to describe.
25 Battery cycle life, min 6,000 cycles at 80% depth of discharge (DoD), measured to an end-of-life criterion of 80% retained rated capacity, at 25 degrees C ambient and 1C charge/discharge rate. Bidder to submit the battery manufacturer's datasheet or pack label stating the cycle count. Where the datasheet does not state depth of discharge and end-of-life retention, the bidder shall confirm both in writing on manufacturer letterhead. A cycle life test report referencing IEC 62620 (or accredited third-party equivalent) shall be provided before delivery acceptance.
26 Battery management system (BMS) compliant with IEC 62619, logging cycle count, depth of discharge and state of health, retrievable by the operator or service technician.
27 Bidder to state battery weight (kg), removal/extraction method, and whether a lifting aid is required for battery removal and replacement.
28 Ambient operating conditions (base configuration): equipment rated for continuous operation in standard indoor warehouse conditions, ambient 0 degrees C to +40 degrees C. All prices in the main schedule are for this base configuration.
29 Seat belt, mandatory for seated configuration.
30 Reverse alarm, acoustic, mandatory.
31 Anti-roll-back system preventing roll-back on inclines.
32 Emergency stop button, mandatory, isolating drive and hydraulic power.
33 Key or pin-code access system for operator authorisation.
34 1 kg fire extinguisher, min.
35 LED floor warning spotlight projecting a red or blue spot onto the floor ahead of or behind the machine to warn pedestrians and oncoming equipment.
36 Camera and monitor assistance for high-level fork placement, mandatory. Bidder to state camera resolution, monitor screen size, mounting position, ingress protection rating and operating temperature range of both camera and monitor.
37 Fork position laser: adjustable fan-shaped beam projected from the forks indicating the exact fork position, red or green; stainless steel housing; min IP67; IK10 shock resistance; line accuracy plus/minus 0.05 mm.
38 Fork height and tilt indicator with digital readout of fork height and mast tilt condition, visible from the operator position.
39 Hygiene and GMP: Easy-to-clean design (smooth surfaces, minimal exposed wiring) to comply with Good Manufacturing Practice standards in medical/pharmaceutical warehouses.
40 Certifications: Equipment to possess CE marking (or equivalent)
41 Compliance with ISO 3691 (or equivalent recognised industrial truck safety standard, e.g. ANSI/ITSDF B56) required.
42 Certificate of Quality Management System according to ISO 9001 in the name of the manufacturer or equivalent certification. In case of ISO9001 the Certificate must be issued by an independent Certifying Body/Agency. If the legal manufacturer and the OEM / manufacturing facility are different entities, certificates must be provided for both.
43 Manufacturer Environmental management system: ISO 14001:2015 and/or equivalent certification and/or internal policy document issued by the Manufacturer related to environmental considerations of the company. If the legal manufacturer and the OEM / manufacturing facility are different entities, documentation covering the actual OEM manufacturing facility (or both) must be provided.
44 Manufacturer's authorization if the bidder is not the manufacturer
45 Owners/operators manual, English, French, Spanish or Arabic depending on destination country.
46 Battery end-of-life: Bidder to provide documentation on safe disposal/recycling of the battery at end-of-life, compliant with local and international hazardous waste regulations.
47 Warranty: Machinery and all accessories under warranty for a minimum of 1 year or 1,500 hours of operation, whichever occurs first. The warranty period shall commence on the date of successful completion of the relevant tests and/or inspections of the goods by UNOPS or the Consignee designated by UNOPS to the Contractor. A warranty certificate shall be provided with the delivery of the goods
48 Warranty Battery: minimum 6 years. The warranty period shall commence on the date of successful completion of the relevant tests and/or inspections of the goods by UNOPS or the Consignee designated by UNOPS to the Contractor. A warranty certificate shall be provided with the delivery of the goods
49 Bidders shall demonstrate an authorised distributor network with full warranty and after-sales service in at least 5 countries of the Africa region, and minimum 3 countries in Asia. Bidders shall submit a list of distributors with names and contact details. The nominated local distributor shall be responsible for warranty and repair of the base item and all additional equipment provided with each item. Failure to demonstrate the required extent of coverage with full warranty and after-sales service will exclude the bidder from further evaluation.
DESIRABLE OPTIONS, PRICED SEPARATELY: Please enter further available options as applicable. If Standard, state "Standard".
50 Repair manual in one or more of English, Spanish, French, Arabic, please indicate.
51 Electric rotating beacon/flashing beacon.
52 Spare parts kit, 1 year / 1,500 hours of operation, min.
53 Alternative Lithium-ion (Li-ion/LFP) Battery Options (e.g. other capacities in kWh)
54 Battery end-of-life: Manufacturer-supported take-back/recycling programme.
55 Cold chain configuration: Equipment rated for continuous operation in cold storage down to -20°C, comprising: - Anti-condensation protection for electrical and electronic assemblies; - Low-temperature-rated hydraulic oil, cold-rated seals, and cold-store tyres/wheels; - Battery self-heating system with BMS low-temperature charge inhibit; - Enclosed cold-store cabin (where available/applicable for the offered model): glass all around, cabin heating, heated front/rear glass (or de-misting system), wipers, and interior/exterior mirrors; - Operator seat/platform heating where an enclosed cabin is not fitted or not standard. Bidder to state the operating temperature range of camera, monitor, and fork laser where fitted. To be quoted as a separate unit price and not included in the base price.
56 Higher-output charger (e.g. a three-phase 400 V charger) - Bidder to define
57 Extended Warranty for 1 year or 3,000 hours of operation, whichever comes first
58 Extended Warranty for 1 year for the battery
Lot 6: Electric Reach Truck, Articulated ("Bendi"-type)
Lifting capacity 2.0 ton, operating range 7.5 to 12.4 m
Name and physical address of actual Manufacturing site(s):
Country of origin:
Product Website:
Item UNOPS Minimum Technical Requirement Complies (Yes / No) Offered Technical Specifications Support for Technical Compliance
1 Propellant, electric.
2 Lifting capacity, ton, min 2.0.
3 Standard lift / operating range: 7.5 m to 12.4 m.
4 Working aisle width, max 2,100 mm, measured as the clear width between the front faces of the stored pallets or rack uprights on both sides, whichever protrudes further. Basis: free-path operation, stacking and retrieving a 1,000 x 1,200 mm pallet with the 1,200 mm side as rack depth by articulating within the aisle. Bidder to state the transfer aisle width needed at the aisle ends.
5 Turning radius, mm, bidder to state. Measured from the centre of rotation to the outermost point of the truck with the steering at full lock.
6 Retracted mast height, mm, bidder to state: overall height of the mast with the forks fully lowered, for the lift height offered. Bidder to state, for the offered mast, the retracted mast height, the free lift (height the forks rise before the mast begins to extend) and the extended mast height with the forks fully raised.
7 Articulating mast/chassis enabling operation in narrow aisles without a fixed rail or wire guidance system, while retaining the ability to also load/unload trailers and work in open yard areas (combined forklift/reach/VNA function).
8 Battery type: Lithium Iron Phosphate (Li-ion / LFP). Other lithium chemistries (NMC, NCA, LTO) and lead-acid batteries are not acceptable.
9 Battery capacity, kWh, min 43
10 Battery charger: wall-mounted AC charger, single-phase 220 to 240 V 50 Hz, maximum AC input current 32 A, rated output approx. 6.0 to 6.6 kW, supplied, fitted and commissioned by the supplier, with all required cables, ready for connection to the local AC electrical grid by a qualified electrician. Bidder to state supported input voltage, phase, frequency and current draw per unit, and the total simultaneous charging load for the quantity offered.
11 Electric protection, min IP54.
12 Battery charge indicator.
13 Operation hour meter.
14 Operator position: seated.
15 Overhead guard for operator protection.
16 Drive motor rating at short-time duty S2, 60 minutes (IEC 60034-1), min 2x 6 kW. Bidder to state the duty type and rating period on which each motor power is quoted, supported by the manufacturer's published technical specification sheet. Where a rating other than the one specified is quoted, the equivalent value on the specified duty basis shall be stated.
17 Lift motor rating at S3 per IEC 60034-1, min 14 kW, bidder to state the cyclic duration factor.
18 Travel speed, laden/unladen, km/h, min 13/14.
19 Max. gradeability, laden, %, min 10 (suitable for semi-outdoor/yard use).
20 Brakes, appropriate for equipment type, with regenerative braking.
21 Parking brake.
22 Non-marking tyres/wheels suitable for both indoor floors and semi-outdoor yard surfaces; bidder to specify.
23 Battery cycle life, min 6,000 cycles at 80% depth of discharge (DoD), measured to an end-of-life criterion of 80% retained rated capacity, at 25 degrees C ambient and 1C charge/discharge rate. Bidder to submit the battery manufacturer's datasheet or pack label stating the cycle count. Where the datasheet does not state depth of discharge and end-of-life retention, the bidder shall confirm both in writing on manufacturer letterhead. A cycle life test report referencing IEC 62620 (or accredited third-party equivalent) shall be provided before delivery acceptance.
24 Battery management system (BMS) compliant with IEC 62619, logging cycle count, depth of discharge and state of health, retrievable by the operator or service technician.
25 Bidder to state battery weight (kg), removal/extraction method, and whether a lifting aid is required for battery removal and replacement.
26 Ambient operating conditions (base configuration): equipment rated for continuous operation indoors, semi-outdoors and outdoors, ambient 0 degrees C to +50 degrees C, with solar and dust exposure protection, UV-resistant finishes and seals, and min IP54 on electrical enclosures. All prices in the main schedule are for this base configuration.
27 Seat belt for the operator, mandatory.
28 Reverse alarm, acoustic, mandatory.
29 Anti-roll-back system preventing roll-back on inclines.
30 Emergency stop button, mandatory, isolating drive and hydraulic power.
31 Key or pin-code access system for operator authorisation.
32 1 kg fire extinguisher, min.
33 LED floor warning spotlight projecting a red or blue spot onto the floor ahead of or behind the machine to warn pedestrians and oncoming equipment.
34 Camera and monitor assistance for high-level fork placement, mandatory. Bidder to state camera resolution, monitor screen size, mounting position, ingress protection rating and operating temperature range of both camera and monitor.
35 Fork position laser: adjustable fan-shaped beam projected from the forks indicating the exact fork position, red or green; stainless steel housing; min IP67; IK10 shock resistance; line accuracy plus/minus 0.05 mm.
36 Fork height and tilt indicator with digital readout of fork height and mast tilt condition, visible from the operator position.
37 Load sensing / stability control system, active at height; bidder to describe.
38 Residual capacity display at height, visible from the operator position.
39 Hygiene and GMP: Easy-to-clean design (smooth surfaces, minimal exposed wiring) to comply with Good Manufacturing Practice standards in medical/pharmaceutical warehouses.
40 Certifications: Equipment to possess CE marking (or equivalent)
41 Compliance with ISO 3691 (or equivalent recognised industrial truck safety standard, e.g. ANSI/ITSDF B56) required.
42 Certificate of Quality Management System according to ISO 9001 in the name of the manufacturer or equivalent certification. In case of ISO9001 the Certificate must be issued by an independent Certifying Body/Agency. If the legal manufacturer and the OEM / manufacturing facility are different entities, certificates must be provided for both.
43 Manufacturer Environmental management system: ISO 14001:2015 and/or equivalent certification and/or internal policy document issued by the Manufacturer related to environmental considerations of the company. If the legal manufacturer and the OEM / manufacturing facility are different entities, documentation covering the actual OEM manufacturing facility (or both) must be provided.
44 Manufacturer's authorization if the bidder is not the manufacturer
45 Owners/operators manual, English, French, Spanish or Arabic depending on destination country.
46 Battery end-of-life: Bidder to provide documentation on safe disposal/recycling of the battery at end-of-life, compliant with local and international hazardous waste regulations.
47 Warranty: Machinery and all accessories under warranty for a minimum of 1 year or 1,500 hours of operation, whichever occurs first. The warranty period shall commence on the date of successful completion of the relevant tests and/or inspections of the goods by UNOPS or the Consignee designated by UNOPS to the Contractor. A warranty certificate shall be provided with the delivery of the goods
48 Warranty Battery: minimum 6 years. The warranty period shall commence on the date of successful completion of the relevant tests and/or inspections of the goods by UNOPS or the Consignee designated by UNOPS to the Contractor. A warranty certificate shall be provided with the delivery of the goods
49 Bidders shall demonstrate an authorised distributor network with full warranty and after-sales service in at least 5 countries of the Africa region, and minimum 3 countries in Asia. Bidders shall submit a list of distributors with names and contact details. The nominated local distributor shall be responsible for warranty and repair of the base item and all additional equipment provided with each item. Failure to demonstrate the required extent of coverage with full warranty and after-sales service will exclude the bidder from further evaluation.
DESIRABLE OPTIONS, PRICED SEPARATELY: Please enter further available options as applicable. If Standard, state "Standard".
50 Repair manual in one or more of English, Spanish, French, Arabic, please indicate.
51 Electric rotating beacon/flashing beacon.
52 Spare parts kit, 1 year / 1,500 hours of operation, min.
53 Alternative Lithium-ion (Li-ion/LFP) Battery Options (e.g. other capacities in kWh)
54 Battery end-of-life: Manufacturer-supported take-back/recycling programme.
55 Cold chain configuration: Equipment rated for continuous operation in cold storage down to -20°C, comprising: - Anti-condensation protection for electrical and electronic assemblies; - Low-temperature-rated hydraulic oil, cold-rated seals, and cold-store tyres/wheels; - Battery self-heating system with BMS low-temperature charge inhibit; - Enclosed cold-store cabin (where available/applicable for the offered model): glass all around, cabin heating, heated front/rear glass (or de-misting system), wipers, and interior/exterior mirrors; - Operator seat/platform heating where an enclosed cabin is not fitted or not standard. Bidder to state the operating temperature range of camera, monitor, and fork laser where fitted. To be quoted as a separate unit price and not included in the base price.
56 Higher-output charger (e.g. a three-phase 400 V charger) - Bidder to define
57 Extended Warranty for 1 year or 3,000 hours of operation, whichever comes first
58 Extended Warranty for 1 year for the battery
Lot 7: VNA Machine, Very Narrow Aisle (Man-Up)
Lifting capacity 1.0 to 1.5 ton, lift height up to 13.8 m
Name and physical address of actual Manufacturing site(s):
Country of origin:
Product Website:
Item UNOPS Minimum Technical Requirement Complies (Yes / No) Offered Technical Specifications Support for Technical Compliance
1 Propellant, electric.
2 Lifting capacity, ton, 1.0 to 1.5
3 Lift height, up to 13.8 m.
4 Working aisle width, max 1,900 mm, measured as the clear width between the front faces of the stored pallets or rack uprights on both sides, whichever protrudes further. Basis: rail-guided operation, stacking and retrieving a 1,000 x 1,200 mm pallet with the 1,200 mm side as rack depth on either side of the aisle. Bidder to state the required distance between guide rails, the guide-roller clearance and the transfer aisle width needed at the aisle ends.
5 Turning radius, mm, bidder to state. Measured from the centre of rotation to the outermost point of the truck with the steering at full lock.
6 Retracted mast height, mm, bidder to state: overall height of the mast with the forks fully lowered, for the lift height offered. Bidder to state, for the offered mast, the retracted mast height, the free lift (height the forks rise before the mast begins to extend) and the extended mast height with the forks fully raised.
7 Configuration: man-up turret truck, swing-reach, or trilateral; bidder to specify.
8 Guidance system required for aisle travel: rail-guided or wire/inductive-guided; bidder to specify and state minimum working aisle width achieved (typical 1,600–1,800 mm).
9 Operator cab: enclosed safety cage with full-body harness, anchor point, and shock-absorbing tether, mandatory for man-up operation.
10 Retractable side gates on the operator cage.
11 Battery type: Lithium Iron Phosphate (Li-ion / LFP). Other lithium chemistries (NMC, NCA, LTO) and lead-acid batteries are not acceptable.
12 Battery capacity, kWh, min 45
13 Battery charger: wall-mounted AC charger, single-phase 220 to 240 V 50 Hz, maximum AC input current 32 A, rated output approx. 6.0 to 6.6 kW, supplied, fitted and commissioned by the supplier, with all required cables, ready for connection to the local AC electrical grid by a qualified electrician. Bidder to state supported input voltage, phase, frequency and current draw per unit, and the total simultaneous charging load for the quantity offered.
14 Electric protection, min IP54.
15 Battery charge indicator.
16 Operation hour meter.
17 Drive motor rating at short-time duty S2, 60 minutes (IEC 60034-1), kW, min 7. Bidder to state the duty type and rating period on which each motor power is quoted, supported by the manufacturer's published technical specification sheet. Where a rating other than the one specified is quoted, the equivalent value on the specified duty basis shall be stated.
18 Lift motor rating at S3 per IEC 60034-1, kW, min 24; bidder to state the cyclic duration factor.
19 Travel speed, laden/unladen, km/h, min 10/10.
20 Lift speed, laden, m/s, bidder to state.
21 Max. gradeability, %, min 5 (indoor VNA use).
22 Brakes, appropriate for equipment type, with regenerative braking.
23 Parking brake.
24 Non-marking tyres/wheels suitable for indoor floors; bidder to specify.
25 Battery cycle life, min 6,000 cycles at 80% depth of discharge (DoD), measured to an end-of-life criterion of 80% retained rated capacity, at 25 degrees C ambient and 1C charge/discharge rate. Bidder to submit the battery manufacturer's datasheet or pack label stating the cycle count. Where the datasheet does not state depth of discharge and end-of-life retention, the bidder shall confirm both in writing on manufacturer letterhead. A cycle life test report referencing IEC 62620 (or accredited third-party equivalent) shall be provided before delivery acceptance.
26 Battery management system (BMS) compliant with IEC 62619, logging cycle count, depth of discharge and state of health, retrievable by the operator or service technician.
27 Bidder to state battery weight (kg), removal/extraction method, and whether a lifting aid is required for battery removal and replacement.
28 Ambient operating conditions (base configuration): equipment rated for continuous operation in standard indoor warehouse conditions, ambient 0 degrees C to +40 degrees C. All prices in the main schedule are for this base configuration.
29 Reverse alarm, acoustic, mandatory.
30 Anti-roll-back system preventing roll-back on inclines.
31 Emergency stop button, mandatory, isolating drive and hydraulic power.
32 Key or pin-code access system for operator authorisation.
33 1 kg fire extinguisher, min.
34 LED floor warning spotlight projecting a red or blue spot onto the floor ahead of or behind the machine to warn pedestrians and oncoming equipment.
35 Hygiene and GMP: Easy-to-clean design (smooth surfaces, minimal exposed wiring) to comply with Good Manufacturing Practice standards in medical/pharmaceutical warehouses.
36 Certifications: Equipment to possess CE marking (or equivalent)
37 Compliance with ISO 3691 (or equivalent recognised industrial truck safety standard, e.g. ANSI/ITSDF B56) required.
38 Certificate of Quality Management System according to ISO 9001 in the name of the manufacturer or equivalent certification. In case of ISO9001 the Certificate must be issued by an independent Certifying Body/Agency. If the legal manufacturer and the OEM / manufacturing facility are different entities, certificates must be provided for both.
39 Manufacturer Environmental management system: ISO 14001:2015 and/or equivalent certification and/or internal policy document issued by the Manufacturer related to environmental considerations of the company. If the legal manufacturer and the OEM / manufacturing facility are different entities, documentation covering the actual OEM manufacturing facility (or both) must be provided.
40 Manufacturer's authorization if the bidder is not the manufacturer
41 Owners/operators manual, English, French, Spanish or Arabic depending on destination country.
42 Battery end-of-life: Bidder to provide documentation on safe disposal/recycling of the battery at end-of-life, compliant with local and international hazardous waste regulations.
43 Warranty: Machinery and all accessories under warranty for a minimum of 1 year or 1,500 hours of operation, whichever occurs first. The warranty period shall commence on the date of successful completion of the relevant tests and/or inspections of the goods by UNOPS or the Consignee designated by UNOPS to the Contractor. A warranty certificate shall be provided with the delivery of the goods
44 Warranty Battery: minimum 6 years. The warranty period shall commence on the date of successful completion of the relevant tests and/or inspections of the goods by UNOPS or the Consignee designated by UNOPS to the Contractor. A warranty certificate shall be provided with the delivery of the goods
45 Bidders shall demonstrate an authorised distributor network with full warranty and after-sales service in at least 5 countries of the Africa region, and minimum 3 countries in Asia. Bidders shall submit a list of distributors with names and contact details. The nominated local distributor shall be responsible for warranty and repair of the base item and all additional equipment provided with each item. Failure to demonstrate the required extent of coverage with full warranty and after-sales service will exclude the bidder from further evaluation.
DESIRABLE OPTIONS, PRICED SEPARATELY: Please enter further available options as applicable. If Standard, state "Standard".
46 Repair manual in one or more of English, Spanish, French, Arabic, please indicate.
47 Electric rotating beacon/flashing beacon.
48 Spare parts kit, 1 year / 1,500 hours of operation, min.
49 Wire-guidance retrofit kit, if not standard.
50 Alternative Lithium-ion (Li-ion/LFP) Battery Options (e.g. other capacities in kWh)
51 Battery end-of-life: Manufacturer-supported take-back/recycling programme.
52 Cold chain configuration: Equipment rated for continuous operation in cold storage down to -20°C, comprising: - Anti-condensation protection for electrical and electronic assemblies; - Low-temperature-rated hydraulic oil, cold-rated seals, and cold-store tyres/wheels; - Battery self-heating system with BMS low-temperature charge inhibit; - Enclosed cold-store cabin (where available/applicable for the offered model): glass all around, cabin heating, heated front/rear glass (or de-misting system), wipers, and interior/exterior mirrors; - Operator seat/platform heating where an enclosed cabin is not fitted or not standard. Bidder to state the operating temperature range of camera, monitor, and fork laser where fitted. To be quoted as a separate unit price and not included in the base price.
53 Higher-output charger (e.g. a three-phase 400 V charger) - Bidder to define
54 Extended Warranty for 1 year or 3,000 hours of operation, whichever comes first
55 Extended Warranty for 1 year for the battery
Lot 8: Electric Pallet Truck, Low Lift – Walkie
Lifting capacity 1.4 to 2.5 ton, horizontal transport
Name and physical address of actual Manufacturing site(s):
Country of origin:
Product Website:
Item UNOPS Minimum Technical Requirement Complies (Yes / No) Offered Technical Specifications Support for Technical Compliance
1 Propellant, electric.
2 Lifting capacity, ton, min 1.4
3 Lift height: low lift (travel clearance only), mm; bidder to state.
4 Working aisle width, max 2,250 mm, measured as the narrowest aisle in which the truck can turn 90° and set down or pick up a 1,000 x 1,200 mm pallet carried crossways (1,000 mm side along the forks), including 200 mm total operating clearance, with the tiller arm in the operating position.
5 Turning radius, max 1,650 mm, measured from the centre of rotation to the outermost point of the truck body, with the tiller arm in the operating position and forks lowered.
6 Operator: pedestrian/walkie, tiller-arm steering with integral speed and direction controls.
7 Battery type: Lithium Iron Phosphate (Li-ion / LFP). Other lithium chemistries (NMC, NCA, LTO) and lead-acid batteries are not acceptable.
8 Battery capacity, kWh, min 2.4
9 Battery charger: 220 V single-phase 50 Hz adapter charger, max 16 A, charging from a standard socket without a dedicated circuit, with all required cables. Bidder to state supported input voltage and frequency range and current draw per unit.
10 Electric protection, min IP54.
11 Battery charge indicator.
12 Operation hour meter.
13 Drive motor rating at short-time duty S2, 60 minutes (IEC 60034-1), kW, min 1.2. Bidder to state the duty type and rating period on which each motor power is quoted, supported by the manufacturer's published technical specification sheet. Where a rating other than the one specified is quoted, the equivalent value on the specified duty basis shall be stated.
14 Lift motor rating at S3 per IEC 60034-1, kW, min 1.2; bidder to state the cyclic duration factor.
15 Travel speed, laden/unladen, km/h, min 4.5/5.5.
16 Brakes: electromagnetic, automatically applied on release of tiller.
17 Fork dimensions compatible with standard 1200x800 mm and 1000x1200 mm pallets; bidder to state fork length/width.
18 Load wheels: non-marking polyurethane.
19 Emergency reverse (belly button) safety switch.
20 Battery cycle life, min 3,000 cycles at 80% depth of discharge (DoD), measured to an end-of-life criterion of 80% retained rated capacity, at 25 degrees C ambient and 1C charge/discharge rate. Bidder to submit the battery manufacturer's datasheet or pack label stating the cycle count. Where the datasheet does not state depth of discharge and end-of-life retention, the bidder shall confirm both in writing on manufacturer letterhead. A cycle life test report referencing IEC 62620 (or accredited third-party equivalent) shall be provided before delivery acceptance.
21 Battery management system (BMS) compliant with IEC 62619, logging cycle count, depth of discharge and state of health, retrievable by the operator or service technician.
22 Bidder to state battery weight (kg), removal/extraction method, and whether a lifting aid is required for battery removal and replacement.
23 Ambient operating conditions (base configuration): equipment rated for continuous operation in standard indoor warehouse conditions, ambient 0 degrees C to +40 degrees C. All prices in the main schedule are for this base configuration.
24 Emergency stop button, mandatory, isolating drive and hydraulic power.
25 Key or pin-code access system for operator authorisation.
26 Hygiene and GMP: Easy-to-clean design (smooth surfaces, minimal exposed wiring) to comply with Good Manufacturing Practice standards in medical/pharmaceutical warehouses.
27 Certifications: Equipment to possess CE marking (or equivalent)
28 Compliance with ISO 3691 (or equivalent recognised industrial truck safety standard, e.g. ANSI/ITSDF B56) required.
29 Certificate of Quality Management System according to ISO 9001 in the name of the manufacturer or equivalent certification. In case of ISO9001 the Certificate must be issued by an independent Certifying Body/Agency. If the legal manufacturer and the OEM / manufacturing facility are different entities, certificates must be provided for both.
30 Manufacturer Environmental management system: ISO 14001:2015 and/or equivalent certification and/or internal policy document issued by the Manufacturer related to environmental considerations of the company. If the legal manufacturer and the OEM / manufacturing facility are different entities, documentation covering the actual OEM manufacturing facility (or both) must be provided.
31 Manufacturer's authorization if the bidder is not the manufacturer
32 Owners/operators manual, English, French, Spanish or Arabic depending on destination country.
33 Battery end-of-life: Bidder to provide documentation on safe disposal/recycling of the battery at end-of-life, compliant with local and international hazardous waste regulations.
34 Warranty: Machinery and all accessories under warranty for a minimum of 1 year or 1,500 hours of operation, whichever occurs first. The warranty period shall commence on the date of successful completion of the relevant tests and/or inspections of the goods by UNOPS or the Consignee designated by UNOPS to the Contractor. A warranty certificate shall be provided with the delivery of the goods
35 Warranty Battery: minimum 6 years. The warranty period shall commence on the date of successful completion of the relevant tests and/or inspections of the goods by UNOPS or the Consignee designated by UNOPS to the Contractor. A warranty certificate shall be provided with the delivery of the goods
36 Bidders shall demonstrate an authorised distributor network with full warranty and after-sales service in at least 5 countries of the Africa region, and minimum 3 countries in Asia. Bidders shall submit a list of distributors with names and contact details. The nominated local distributor shall be responsible for warranty and repair of the base item and all additional equipment provided with each item. Failure to demonstrate the required extent of coverage with full warranty and after-sales service will exclude the bidder from further evaluation.
DESIRABLE OPTIONS, PRICED SEPARATELY: Please enter further available options as applicable. If Standard, state "Standard".
37 Repair manual in one or more of English, Spanish, French, Arabic, please indicate.
38 Spare parts kit, 1 year / 1,500 hours of operation, min.
39 Alternative Lithium-ion (Li-ion/LFP) Battery Options (e.g. other capacities in kWh)
40 Battery end-of-life: Manufacturer-supported take-back/recycling programme.
41 Cold chain configuration: equipment rated for continuous operation in cold storage down to -20 degrees C, comprising anti-condensation protection for electrical and electronic assemblies, low-temperature-rated hydraulic oil, cold-rated seals and wheels, battery self-heating with BMS low-temperature charge inhibit, and operator heating where an enclosed or seated operator position exists. Bidder to state the operating temperature range of camera, monitor and fork laser where fitted. To be quoted as a separate unit price and not included in the base price.
42 Higher-output charger (e.g. a three-phase 400 V charger) - Bidder to define
43 Extended Warranty for 1 year or 3,000 hours of operation, whichever comes first
44 Extended Warranty for 1 year for the battery
Lot 9: Electric Pallet Truck, Low Lift – Rider
Lifting capacity 2.5 to 3.5 ton, horizontal transport
Name and physical address of actual Manufacturing site(s):
Country of origin:
Product Website:
Item UNOPS Minimum Technical Requirement Complies (Yes / No) Offered Technical Specifications Support for Technical Compliance
1 Propellant, electric.
2 Lifting capacity, ton, min 2.5
3 Lift height: low lift (travel clearance only), mm; bidder to state.
4 Working aisle width, max 3,800 mm, measured as the narrowest aisle in which the truck can turn 90° and set down or pick up a 1,000 x 1,200 mm pallet carried crossways (1,000 mm side along the forks), including 200 mm total operating clearance, with the operator platform folded down and side guards in place.
5 Turning radius, bidder to state, measured from the centre of rotation to the outermost point of the truck body, with the operator platform folded down and forks lowered.
6 Operator: fold-down rider platform (stand-on), with tiller or steering-wheel control; bidder to specify.
7 Battery type: Lithium Iron Phosphate (Li-ion / LFP). Other lithium chemistries (NMC, NCA, LTO) and lead-acid batteries are not acceptable.
8 Battery capacity, kWh, min 6
9 Battery charger: 220 V single-phase 50 Hz adapter charger, max 16 A, charging from a standard socket without a dedicated circuit, with all required cables. Bidder to state supported input voltage and frequency range and current draw per unit.
10 Electric protection, min IP54.
11 Battery charge indicator.
12 Operation hour meter.
13 Drive motor rating at short-time duty S2, 60 minutes (IEC 60034-1), kW, min 3.0. Bidder to state the duty type and rating period on which each motor power is quoted, supported by the manufacturer's published technical specification sheet. Where a rating other than the one specified is quoted, the equivalent value on the specified duty basis shall be stated.
14 Lift motor rating at S3 per IEC 60034-1, kW; bidder to state, with the cyclic duration factor.
15 Travel speed, laden/unladen, km/h, min 9/12.
16 Brakes: electromagnetic/hydraulic, with regenerative braking, plus parking brake.
17 Fork dimensions compatible with standard 1200x800 mm and 1000x1200 mm pallets; bidder to state fork length/width.
18 Load wheels: non-marking polyurethane.
19 Working lights and acoustic horn (used over longer transport distances).
20 Emergency reverse (belly button) safety switch.
21 Battery cycle life, min 3,000 cycles at 80% depth of discharge (DoD), measured to an end-of-life criterion of 80% retained rated capacity, at 25 degrees C ambient and 1C charge/discharge rate. Bidder to submit the battery manufacturer's datasheet or pack label stating the cycle count. Where the datasheet does not state depth of discharge and end-of-life retention, the bidder shall confirm both in writing on manufacturer letterhead. A cycle life test report referencing IEC 62620 (or accredited third-party equivalent) shall be provided before delivery acceptance.
22 Battery management system (BMS) compliant with IEC 62619, logging cycle count, depth of discharge and state of health, retrievable by the operator or service technician.
23 Bidder to state battery weight (kg), removal/extraction method, and whether a lifting aid is required for battery removal and replacement.
24 Ambient operating conditions (base configuration): equipment rated for continuous operation in standard indoor warehouse conditions, ambient 0 degrees C to +40 degrees C. All prices in the main schedule are for this base configuration.
25 Reverse alarm, acoustic, mandatory.
26 Emergency stop button, mandatory, isolating drive and hydraulic power.
27 Key or pin-code access system for operator authorisation.
28 1 kg fire extinguisher, min.
29 Hygiene and GMP: Easy-to-clean design (smooth surfaces, minimal exposed wiring) to comply with Good Manufacturing Practice standards in medical/pharmaceutical warehouses.
30 Certifications: Equipment to possess CE marking (or equivalent)
31 Compliance with ISO 3691 (or equivalent recognised industrial truck safety standard, e.g. ANSI/ITSDF B56) required.
32 Certificate of Quality Management System according to ISO 9001 in the name of the manufacturer or equivalent certification. In case of ISO9001 the Certificate must be issued by an independent Certifying Body/Agency. If the legal manufacturer and the OEM / manufacturing facility are different entities, certificates must be provided for both.
33 Manufacturer Environmental management system: ISO 14001:2015 and/or equivalent certification and/or internal policy document issued by the Manufacturer related to environmental considerations of the company. If the legal manufacturer and the OEM / manufacturing facility are different entities, documentation covering the actual OEM manufacturing facility (or both) must be provided.
34 Manufacturer's authorization if the bidder is not the manufacturer
35 Owners/operators manual, English, French, Spanish or Arabic depending on destination country.
36 Battery end-of-life: Bidder to provide documentation on safe disposal/recycling of the battery at end-of-life, compliant with local and international hazardous waste regulations.
37 Warranty: Machinery and all accessories under warranty for a minimum of 1 year or 1,500 hours of operation, whichever occurs first. The warranty period shall commence on the date of successful completion of the relevant tests and/or inspections of the goods by UNOPS or the Consignee designated by UNOPS to the Contractor. A warranty certificate shall be provided with the delivery of the goods
38 Warranty Battery: minimum 6 years. The warranty period shall commence on the date of successful completion of the relevant tests and/or inspections of the goods by UNOPS or the Consignee designated by UNOPS to the Contractor. A warranty certificate shall be provided with the delivery of the goods
39 Bidders shall demonstrate an authorised distributor network with full warranty and after-sales service in at least 5 countries of the Africa region, and minimum 3 countries in Asia. Bidders shall submit a list of distributors with names and contact details. The nominated local distributor shall be responsible for warranty and repair of the base item and all additional equipment provided with each item. Failure to demonstrate the required extent of coverage with full warranty and after-sales service will exclude the bidder from further evaluation.
DESIRABLE OPTIONS, PRICED SEPARATELY: Please enter further available options as applicable. If Standard, state "Standard".
40 Repair manual in one or more of English, Spanish, French, Arabic, please indicate.
41 Electric rotating beacon/flashing beacon.
42 Spare parts kit, 1 year / 1,500 hours of operation, min.
43 Alternative Lithium-ion (Li-ion/LFP) Battery Options (e.g. other capacities in kWh)
44 Battery end-of-life: Manufacturer-supported take-back/recycling programme.
45 Cold chain configuration: equipment rated for continuous operation in cold storage down to -20 degrees C, comprising anti-condensation protection for electrical and electronic assemblies, low-temperature-rated hydraulic oil, cold-rated seals and wheels, battery self-heating with BMS low-temperature charge inhibit, and operator heating where an enclosed or seated operator position exists. Bidder to state the operating temperature range of camera, monitor and fork laser where fitted. To be quoted as a separate unit price and not included in the base price.
46 Higher-output charger (e.g. a three-phase 400 V charger) - Bidder to define
47 Extended Warranty for 1 year or 3,000 hours of operation, whichever comes first
48 Extended Warranty for 1 year for the battery
Lot 10: Electric Pallet Truck / Stacker, High Lift – Walkie Stacker
Lifting capacity 1.0 to 1.6 ton, stacking up to 4.5 m
Name and physical address of actual Manufacturing site(s):
Country of origin:
Product Website:
Item UNOPS Minimum Technical Requirement Complies (Yes / No) Offered Technical Specifications Support for Technical Compliance
1 Propellant, electric.
2 Lifting capacity, ton, min 1.0
3 Lift height, up to 4.5 m.
4 Working aisle width, mm, max 2,400. Measured as the narrowest aisle in which the truck can turn and stack a 1000 x 1200 mm pallet handled crossways, including 200 mm total operating clearance. Bidder to state the figure for the mast, tyre and fork configuration actually offered.
5 Turning radius, mm, max 1,700. Measured from the centre of rotation to the outermost point of the truck with the steering at full lock.
6 Retracted mast height, mm, bidder to state: overall height of the mast with the forks fully lowered, for the lift height offered. Bidder to state, for the offered mast, the retracted mast height, the free lift (height the forks rise before the mast begins to extend) and the extended mast height with the forks fully raised.
7 Straddle legs: fixed or adjustable width; bidder to specify and state compatibility with closed-bottom/GMA-style pallets if adjustable.
8 Operator: pedestrian/walkie, with optional stand-on platform; bidder to specify.
9 Battery type: Lithium Iron Phosphate (Li-ion / LFP). Other lithium chemistries (NMC, NCA, LTO) and lead-acid batteries are not acceptable.
10 Battery capacity, kWh, min 5
11 Battery charger: 220 V single-phase 50 Hz adapter charger, max 16 A, charging from a standard socket without a dedicated circuit, with all required cables. Bidder to state supported input voltage and frequency range and current draw per unit.
12 Electric protection, min IP54.
13 Battery charge indicator.
14 Operation hour meter.
15 Drive motor rating at short-time duty S2, 60 minutes (IEC 60034-1), kW, min 1.5. Bidder to state the duty type and rating period on which each motor power is quoted, supported by the manufacturer's published technical specification sheet. Where a rating other than the one specified is quoted, the equivalent value on the specified duty basis shall be stated.
16 Lift motor rating at S3 per IEC 60034-1, kW, min 2.2; bidder to state the cyclic duration factor.
17 Travel speed, laden/unladen, km/h, min 5/5.
18 Lift speed, laden, m/s, bidder to state.
19 Brakes: electromagnetic, plus parking brake.
20 Fork width adjustable to accommodate standard pallet types.
21 Load wheels: non-marking polyurethane.
22 Overload cutoff and controlled descent/lowering speed limiter.
23 Battery cycle life, min 3,000 cycles at 80% depth of discharge (DoD), measured to an end-of-life criterion of 80% retained rated capacity, at 25 degrees C ambient and 1C charge/discharge rate. Bidder to submit the battery manufacturer's datasheet or pack label stating the cycle count. Where the datasheet does not state depth of discharge and end-of-life retention, the bidder shall confirm both in writing on manufacturer letterhead. A cycle life test report referencing IEC 62620 (or accredited third-party equivalent) shall be provided before delivery acceptance.
24 Battery management system (BMS) compliant with IEC 62619, logging cycle count, depth of discharge and state of health, retrievable by the operator or service technician.
25 Bidder to state battery weight (kg), removal/extraction method, and whether a lifting aid is required for battery removal and replacement.
26 Ambient operating conditions (base configuration): equipment rated for continuous operation in standard indoor warehouse conditions, ambient 0 degrees C to +40 degrees C. All prices in the main schedule are for this base configuration.
27 Emergency stop button, mandatory, isolating drive and hydraulic power.
28 Key or pin-code access system for operator authorisation.
29 Hygiene and GMP: Easy-to-clean design (smooth surfaces, minimal exposed wiring) to comply with Good Manufacturing Practice standards in medical/pharmaceutical warehouses.
30 Certifications: Equipment to possess CE marking (or equivalent)
31 Compliance with ISO 3691 (or equivalent recognised industrial truck safety standard, e.g. ANSI/ITSDF B56) required.
32 Certificate of Quality Management System according to ISO 9001 in the name of the manufacturer or equivalent certification. In case of ISO9001 the Certificate must be issued by an independent Certifying Body/Agency. If the legal manufacturer and the OEM / manufacturing facility are different entities, certificates must be provided for both.
33 Manufacturer Environmental management system: ISO 14001:2015 and/or equivalent certification and/or internal policy document issued by the Manufacturer related to environmental considerations of the company. If the legal manufacturer and the OEM / manufacturing facility are different entities, documentation covering the actual OEM manufacturing facility (or both) must be provided.
34 Manufacturer's authorization if the bidder is not the manufacturer
35 Owners/operators manual, English, French, Spanish or Arabic depending on destination country.
36 Battery end-of-life: Bidder to provide documentation on safe disposal/recycling of the battery at end-of-life, compliant with local and international hazardous waste regulations.
37 Warranty: Machinery and all accessories under warranty for a minimum of 1 year or 1,500 hours of operation, whichever occurs first. The warranty period shall commence on the date of successful completion of the relevant tests and/or inspections of the goods by UNOPS or the Consignee designated by UNOPS to the Contractor. A warranty certificate shall be provided with the delivery of the goods
38 Warranty Battery: minimum 6 years. The warranty period shall commence on the date of successful completion of the relevant tests and/or inspections of the goods by UNOPS or the Consignee designated by UNOPS to the Contractor. A warranty certificate shall be provided with the delivery of the goods
39 Bidders shall demonstrate an authorised distributor network with full warranty and after-sales service in at least 5 countries of the Africa region, and minimum 3 countries in Asia. Bidders shall submit a list of distributors with names and contact details. The nominated local distributor shall be responsible for warranty and repair of the base item and all additional equipment provided with each item. Failure to demonstrate the required extent of coverage with full warranty and after-sales service will exclude the bidder from further evaluation.
DESIRABLE OPTIONS, PRICED SEPARATELY: Please enter further available options as applicable. If Standard, state "Standard".
40 Repair manual in one or more of English, Spanish, French, Arabic, please indicate.
41 Electric rotating beacon/flashing beacon.
42 Spare parts kit, 1 year / 1,500 hours of operation, min.
43 Alternative Lithium-ion (Li-ion/LFP) Battery Options (e.g. other capacities in kWh)
44 Battery end-of-life: Manufacturer-supported take-back/recycling programme.
45 Cold chain configuration: equipment rated for continuous operation in cold storage down to -20 degrees C, comprising anti-condensation protection for electrical and electronic assemblies, low-temperature-rated hydraulic oil, cold-rated seals and wheels, battery self-heating with BMS low-temperature charge inhibit, and operator heating where an enclosed or seated operator position exists. Bidder to state the operating temperature range of camera, monitor and fork laser where fitted. To be quoted as a separate unit price and not included in the base price.
46 Higher-output charger (e.g. a three-phase 400 V charger) - Bidder to define
47 Extended Warranty for 1 year or 3,000 hours of operation, whichever comes first
48 Extended Warranty for 1 year for the battery
49 Operator stand-on platform (foldable or fixed), if not included as standard in base offered model
Lot 11: Manual Pallet Jack
Lifting capacity min 3 ton, fork height range approx. 85 to 200 mm
Name and physical address of actual Manufacturing site(s):
Country of origin:
Product Website:
Item UNOPS Minimum Technical Requirement Complies (Yes / No) Offered Technical Specifications Support for Technical Compliance
1 Propellant: manual (hand-operated hydraulic pump).
2 Lifting capacity, ton, min 3.
3 Fork height range, lowered to raised, 85 mm to 200 mm.
4 Working aisle width, bidder to state, measured as the narrowest aisle in which one operator can turn the pallet jack 90° and set down or pick up a 1,000 x 1,200 mm pallet carried crossways (1,000 mm side along the forks), including 200 mm total operating clearance, with the handle in the operating position.
5 Turning radius, bidder to state, measured from the centre of rotation to the outermost point of the frame, with the handle upright and forks lowered.
6 Fork dimensions compatible with standard 1200x800 mm (Euro) and 1000x1200 mm pallets; bidder to state fork length and width offered (e.g. 550x1150 mm or 685x1220 mm).
7 Hydraulic pump: single or double-acting; bidder to specify.
8 Load wheels: non-marking polyurethane; steer wheels: non-marking polyurethane or nylon; bidder to specify.
9 Parking/hold function on the hydraulic release mechanism.
10 Ambient operating conditions (base configuration): equipment rated for continuous operation in standard indoor warehouse conditions, ambient 0 degrees C to +40 degrees C. All prices in the main schedule are for this base configuration.
11 Hygiene and GMP: Easy-to-clean design (smooth surfaces) to comply with Good Manufacturing Practice standards in medical/pharmaceutical warehouses.
12 Certifications: Equipment to possess CE marking (or equivalent)
13 Certificate of Quality Management System according to ISO 9001 in the name of the manufacturer or equivalent certification. In case of ISO9001 the Certificate must be issued by an independent Certifying Body/Agency. If the legal manufacturer and the OEM / manufacturing facility are different entities, certificates must be provided for both.
14 Manufacturer Environmental management system: ISO 14001:2015 and/or equivalent certification and/or internal policy document issued by the Manufacturer related to environmental considerations of the company. If the legal manufacturer and the OEM / manufacturing facility are different entities, documentation covering the actual OEM manufacturing facility (or both) must be provided.
15 Compliance with ISO 3691-5 (pedestrian-propelled trucks) or equivalent.
16 Manufacturer's authorization if the bidder is not the manufacturer
17 Owners/operators manual, English, French, Spanish or Arabic depending on destination country.
18 Warranty: Machinery and all accessories under warranty for a minimum of 1 year. The warranty period shall commence on the date of successful completion of the relevant tests and/or inspections of the goods by UNOPS or the Consignee designated by UNOPS to the Contractor. A warranty certificate shall be provided with the delivery of the goods
19 Bidders shall demonstrate an authorised distributor network with full warranty and after-sales service in at least 5 countries of the Africa region, and minimum 3 countries in Asia. Bidders shall submit a list of distributors with names and contact details. The nominated local distributor shall be responsible for warranty and repair of the base item and all additional equipment provided with each item. Failure to demonstrate the required extent of coverage with full warranty and after-sales service will exclude the bidder from further evaluation.
DESIRABLE OPTIONS, PRICED SEPARATELY: Please enter further available options as applicable. If Standard, state "Standard".
20 Repair/service manual in one or more of English, Spanish, French, Arabic, please indicate.
21 Spare seal/wheel kit for preventative maintenance.
22 Cold chain configuration: low-temperature-rated hydraulic oil and cold-rated seals and wheels for continuous operation in cold storage down to -20 degrees C. To be quoted as a separate unit price and not included in the base price.
23 Extended Warranty for 1 year.
Lot 12: Electric Order Picker, Low Level
Lifting capacity 1.0 ton, platform elevation max 2.0 m
Name and physical address of actual Manufacturing site(s):
Country of origin:
Product Website:
Item UNOPS Minimum Technical Requirement Complies (Yes / No) Offered Technical Specifications Support for Technical Compliance
1 Propellant, electric.
2 Rated load on platform/forks, ton, min 1.0
3 Platform elevation, max 2.0 m.
4 Working aisle width, mm, max 3,200. Measured as the narrowest aisle in which the truck can turn and stack a 1000 x 1200 mm pallet handled crossways, including 200 mm total operating clearance. Bidder to state the figure for the mast, tyre and fork configuration actually offered.
5 Turning radius, mm, bidder to state. Measured from the centre of rotation to the outermost point of the truck with the steering at full lock.
6 Operator: stand-on platform at ground to low level, with walk-through access.
7 Battery type: Lithium Iron Phosphate (Li-ion / LFP). Other lithium chemistries (NMC, NCA, LTO) and lead-acid batteries are not acceptable.
8 Battery capacity, kWh, min 9
9 Battery charger: wall-mounted AC charger, single-phase 220 to 240 V 50 Hz, maximum AC input current 32 A, rated output approx. 6.0 to 6.6 kW, supplied, fitted and commissioned by the supplier, with all required cables, ready for connection to the local AC electrical grid by a qualified electrician. Bidder to state supported input voltage, phase, frequency and current draw per unit, and the total simultaneous charging load for the quantity offered.
10 Electric protection, min IP54.
11 Battery charge indicator.
12 Operation hour meter.
13 Drive motor rating at short-time duty S2, 60 minutes (IEC 60034-1), kW, min 1.8. Bidder to state the duty type and rating period on which each motor power is quoted, supported by the manufacturer's published technical specification sheet. Where a rating other than the one specified is quoted, the equivalent value on the specified duty basis shall be stated.
14 Lift motor rating at S3 per IEC 60034-1, kW, min 2.0; bidder to state the cyclic duration factor.
15 Travel speed, laden/unladen, km/h, min 8/9.
16 Brakes: electromagnetic/hydraulic, plus parking brake and deadman/presence pedal.
17 Toe guards and platform edge protection.
18 Load wheels: non-marking polyurethane.
19 Battery cycle life, min 3,000 cycles at 80% depth of discharge (DoD), measured to an end-of-life criterion of 80% retained rated capacity, at 25 degrees C ambient and 1C charge/discharge rate. Bidder to submit the battery manufacturer's datasheet or pack label stating the cycle count. Where the datasheet does not state depth of discharge and end-of-life retention, the bidder shall confirm both in writing on manufacturer letterhead. A cycle life test report referencing IEC 62620 (or accredited third-party equivalent) shall be provided before delivery acceptance.
20 Battery management system (BMS) compliant with IEC 62619, logging cycle count, depth of discharge and state of health, retrievable by the operator or service technician.
21 Bidder to state battery weight (kg), removal/extraction method, and whether a lifting aid is required for battery removal and replacement.
22 Ambient operating conditions (base configuration): equipment rated for continuous operation in standard indoor warehouse conditions, ambient 0 degrees C to +40 degrees C. All prices in the main schedule are for this base configuration.
23 Reverse alarm, acoustic, mandatory.
24 Emergency stop button, mandatory, isolating drive and hydraulic power.
25 Key or pin-code access system for operator authorisation.
26 1 kg fire extinguisher, min.
27 Hygiene and GMP: Easy-to-clean design (smooth surfaces, minimal exposed wiring) to comply with Good Manufacturing Practice standards in medical/pharmaceutical warehouses.
28 Certifications: Equipment to possess CE marking (or equivalent)
29 Compliance with ISO 3691 (or equivalent recognised industrial truck safety standard, e.g. ANSI/ITSDF B56) required.
30 Certificate of Quality Management System according to ISO 9001 in the name of the manufacturer or equivalent certification. In case of ISO9001 the Certificate must be issued by an independent Certifying Body/Agency. If the legal manufacturer and the OEM / manufacturing facility are different entities, certificates must be provided for both.
31 Manufacturer Environmental management system: ISO 14001:2015 and/or equivalent certification and/or internal policy document issued by the Manufacturer related to environmental considerations of the company. If the legal manufacturer and the OEM / manufacturing facility are different entities, documentation covering the actual OEM manufacturing facility (or both) must be provided.
32 Manufacturer's authorization if the bidder is not the manufacturer
33 Owners/operators manual, English, French, Spanish or Arabic depending on destination country.
34 Battery end-of-life: Bidder to provide documentation on safe disposal/recycling of the battery at end-of-life, compliant with local and international hazardous waste regulations.
35 Warranty: Machinery and all accessories under warranty for a minimum of 1 year or 1,500 hours of operation, whichever occurs first. The warranty period shall commence on the date of successful completion of the relevant tests and/or inspections of the goods by UNOPS or the Consignee designated by UNOPS to the Contractor. A warranty certificate shall be provided with the delivery of the goods
36 Warranty Battery: minimum 6 years. The warranty period shall commence on the date of successful completion of the relevant tests and/or inspections of the goods by UNOPS or the Consignee designated by UNOPS to the Contractor. A warranty certificate shall be provided with the delivery of the goods
37 Bidders shall demonstrate an authorised distributor network with full warranty and after-sales service in at least 5 countries of the Africa region, and minimum 3 countries in Asia. Bidders shall submit a list of distributors with names and contact details. The nominated local distributor shall be responsible for warranty and repair of the base item and all additional equipment provided with each item. Failure to demonstrate the required extent of coverage with full warranty and after-sales service will exclude the bidder from further evaluation.
DESIRABLE OPTIONS, PRICED SEPARATELY: Please enter further available options as applicable. If Standard, state "Standard".
38 Repair manual in one or more of English, Spanish, French, Arabic, please indicate.
39 Spare parts kit, 1 year / 1,500 hours of operation, min.
39 Integrated barcode scanner/computer terminal mounting.
40 Alternative Lithium-ion (Li-ion/LFP) Battery Options (e.g. other capacities in kWh)
40 Battery end-of-life: Manufacturer-supported take-back/recycling programme.
41 Cold chain configuration: equipment rated for continuous operation in cold storage down to -20 degrees C, comprising anti-condensation protection for electrical and electronic assemblies, low-temperature-rated hydraulic oil, cold-rated seals and wheels, battery self-heating with BMS low-temperature charge inhibit, and operator heating where an enclosed or seated operator position exists. Bidder to state the operating temperature range of camera, monitor and fork laser where fitted. To be quoted as a separate unit price and not included in the base price.
41 Higher-output charger (e.g. a three-phase 400 V charger) - Bidder to define
42 Extended Warranty for 1 year or 3,000 hours of operation, whichever comes first
42 Extended Warranty for 1 year for the battery
Lot 13: Electric Order Picker, Medium Level
Lifting capacity 1.0 ton, platform elevation max 6.0 m
Name and physical address of actual Manufacturing site(s):
Country of origin:
Product Website:
Item UNOPS Minimum Technical Requirement Complies (Yes / No) Offered Technical Specifications Support for Technical Compliance
1 Propellant, electric.
2 Rated load on platform/forks, ton, min 1.0
3 Platform elevation, max 6.0 m.
4 Working aisle width, measured as the clear width between the front faces of the stored pallets or rack uprights on both sides, whichever protrudes further, carrying a 1,000 x 1,200 mm pallet with the 1,200 mm side along the forks. Base offer, free-path (unguided) operation: bidder to state working aisle width and transfer aisle width. Guidance options (rail or wire) are optional; see Items 45 and 46
5 Turning radius, mm, bidder to state. Measured from the centre of rotation to the outermost point of the truck with the steering at full lock.
6 Retracted mast height, mm, bidder to state: overall height of the mast with the forks fully lowered, for the lift height offered. Bidder to state, for the offered mast, the retracted mast height, the free lift (height the forks rise before the mast begins to extend) and the extended mast height with the forks fully raised.
7 Operator: rising platform with walk-through access and overhead guard.
8 Fall-arrest full-body harness, anchor point, and shock-absorbing tether, mandatory above 1 m platform height, supplied with each unit.
9 Retractable side gates on the operator platform.
10 Battery type: Lithium Iron Phosphate (Li-ion / LFP). Other lithium chemistries (NMC, NCA, LTO) and lead-acid batteries are not acceptable.
11 Battery capacity, kWh, min 13.4
12 Battery charger: wall-mounted AC charger, single-phase 220 to 240 V 50 Hz, maximum AC input current 32 A, rated output approx. 6.0 to 6.6 kW, supplied, fitted and commissioned by the supplier, with all required cables, ready for connection to the local AC electrical grid by a qualified electrician. Bidder to state supported input voltage, phase, frequency and current draw per unit, and the total simultaneous charging load for the quantity offered.
13 Electric protection, min IP54.
14 Battery charge indicator.
15 Operation hour meter.
16 Drive motor rating at short-time duty S2, 60 minutes (IEC 60034-1), kW, min 1.8. Bidder to state the duty type and rating period on which each motor power is quoted, supported by the manufacturer's published technical specification sheet. Where a rating other than the one specified is quoted, the equivalent value on the specified duty basis shall be stated.
17 Lift motor rating at S3 per IEC 60034-1, kW, min 5.0; bidder to state the cyclic duration factor.
18 Travel speed, laden/unladen, km/h, min 9/9.
19 Brakes: electromagnetic/hydraulic, plus parking brake and deadman/presence pedal.
20 Load wheels: non-marking polyurethane.
21 Battery cycle life, min 6,000 cycles at 80% depth of discharge (DoD), measured to an end-of-life criterion of 80% retained rated capacity, at 25 degrees C ambient and 1C charge/discharge rate. Bidder to submit the battery manufacturer's datasheet or pack label stating the cycle count. Where the datasheet does not state depth of discharge and end-of-life retention, the bidder shall confirm both in writing on manufacturer letterhead. A cycle life test report referencing IEC 62620 (or accredited third-party equivalent) shall be provided before delivery acceptance.
22 Battery management system (BMS) compliant with IEC 62619, logging cycle count, depth of discharge and state of health, retrievable by the operator or service technician.
23 Bidder to state battery weight (kg), removal/extraction method, and whether a lifting aid is required for battery removal and replacement.
24 Ambient operating conditions (base configuration): equipment rated for continuous operation in standard indoor warehouse conditions, ambient 0 degrees C to +40 degrees C. All prices in the main schedule are for this base configuration.
25 Reverse alarm, acoustic, mandatory.
26 Emergency stop button, mandatory, isolating drive and hydraulic power.
27 Key or pin-code access system for operator authorisation.
28 1 kg fire extinguisher, min.
29 Hygiene and GMP: Easy-to-clean design (smooth surfaces, minimal exposed wiring) to comply with Good Manufacturing Practice standards in medical/pharmaceutical warehouses.
30 Certifications: Equipment to possess CE marking (or equivalent)
31 Compliance with ISO 3691 (or equivalent recognised industrial truck safety standard, e.g. ANSI/ITSDF B56) required.
32 Certificate of Quality Management System according to ISO 9001 in the name of the manufacturer or equivalent certification. In case of ISO9001 the Certificate must be issued by an independent Certifying Body/Agency. If the legal manufacturer and the OEM / manufacturing facility are different entities, certificates must be provided for both.
33 Manufacturer Environmental management system: ISO 14001:2015 and/or equivalent certification and/or internal policy document issued by the Manufacturer related to environmental considerations of the company. If the legal manufacturer and the OEM / manufacturing facility are different entities, documentation covering the actual OEM manufacturing facility (or both) must be provided.
34 Manufacturer's authorization if the bidder is not the manufacturer
35 Owners/operators manual, English, French, Spanish or Arabic depending on destination country.
36 Battery end-of-life: Bidder to provide documentation on safe disposal/recycling of the battery at end-of-life, compliant with local and international hazardous waste regulations.
37 Warranty: Machinery and all accessories under warranty for a minimum of 1 year or 1,500 hours of operation, whichever occurs first. The warranty period shall commence on the date of successful completion of the relevant tests and/or inspections of the goods by UNOPS or the Consignee designated by UNOPS to the Contractor. A warranty certificate shall be provided with the delivery of the goods
38 Warranty Battery: minimum 6 years. The warranty period shall commence on the date of successful completion of the relevant tests and/or inspections of the goods by UNOPS or the Consignee designated by UNOPS to the Contractor. A warranty certificate shall be provided with the delivery of the goods
39 Bidders shall demonstrate an authorised distributor network with full warranty and after-sales service in at least 5 countries of the Africa region, and minimum 3 countries in Asia. Bidders shall submit a list of distributors with names and contact details. The nominated local distributor shall be responsible for warranty and repair of the base item and all additional equipment provided with each item. Failure to demonstrate the required extent of coverage with full warranty and after-sales service will exclude the bidder from further evaluation.
DESIRABLE OPTIONS, PRICED SEPARATELY: Please enter further available options as applicable. If Standard, state "Standard".
40 Repair manual in one or more of English, Spanish, French, Arabic, please indicate.
41 Spare parts kit, 1 year / 1,500 hours of operation, min.
42 Integrated barcode scanner/computer terminal mounting.
43 Alternative Lithium-ion (Li-ion/LFP) Battery Options (e.g. other capacities in kWh)
44 Battery end-of-life: Manufacturer-supported take-back/recycling programme.
45 Mechanical rail guidance system (chassis guide rollers): Bidder to state achieved working aisle width (max 1,930 mm), guide roller dimensions, required rail gauge/clearance, and transfer aisle width
46 Wire/inductive guidance system (on-board sensors & steering controller): Bidder to state achieved working aisle width (max 1,930 mm), wire frequency/compatibility, guidance tolerance, and transfer aisle width. Bidder to provide full pre-installation technical requirements.
46a On-truck guidance equipment: On-board sensors and steering controller fitted to the truck. Priced per truck.
46b Frequency generator: Stationary line driver/frequency generator unit to energize the floor wire loop. Priced per unit.
46c Floor wire installation: Floor slot cutting, wire laying, joint sealing, and commissioning. Bidder to state floor requirements before installation. Floor repair or levelling is excluded. Priced per linear meter of aisle.
47 Cold chain configuration: equipment rated for continuous operation in cold storage down to -20 degrees C, comprising anti-condensation protection for electrical and electronic assemblies, low-temperature-rated hydraulic oil, cold-rated seals and wheels, battery self-heating with BMS low-temperature charge inhibit, and operator heating where an enclosed or seated operator position exists. To be quoted as a separate unit price and not included in the base price.
48 Higher-output charger (e.g. a three-phase 400 V charger) - Bidder to define
49 Extended Warranty for 1 year or 3,000 hours of operation, whichever comes first
50 Extended Warranty for 1 year for the battery
Lot 14: Electric Order Picker, High Level – Man Up
Lifting capacity 1.0 ton, platform elevation max 10.0 m
Name and physical address of actual Manufacturing site(s):
Country of origin:
Product Website:
Item UNOPS Minimum Technical Requirement Complies (Yes / No) Offered Technical Specifications Support for Technical Compliance
1 Propellant, electric.
2 Rated load on platform/forks, ton, min 1.0
3 Platform elevation, max 10.0 m.
4 Working aisle width, measured as the clear width between the front faces of the stored pallets or rack uprights on both sides, whichever protrudes further, carrying a 1,000 x 1,200 mm pallet with the 1,200 mm side along the forks. Base offer, free-path (unguided) operation: bidder to state working aisle width and transfer aisle width. Guidance options (rail or wire) are optional; see Items 44 and 45
5 Turning radius, mm, bidder to state. Measured from the centre of rotation to the outermost point of the truck with the steering at full lock.
6 Retracted mast height, mm, bidder to state: overall height of the mast with the forks fully lowered, for the lift height offered. Bidder to state, for the offered mast, the retracted mast height, the free lift (height the forks rise before the mast begins to extend) and the extended mast height with the forks fully raised.
7 Operator: rising platform/cage with full enclosure or high side gates at elevated height.
8 Fall-arrest full-body harness, anchor point, and shock-absorbing tether, mandatory, supplied with each unit.
9 Battery type: Lithium Iron Phosphate (Li-ion / LFP). Other lithium chemistries (NMC, NCA, LTO) and lead-acid batteries are not acceptable.
10 Battery capacity, kWh, min 18
11 Battery charger: wall-mounted AC charger, single-phase 220 to 240 V 50 Hz, maximum AC input current 32 A, rated output approx. 6.0 to 6.6 kW, supplied, fitted and commissioned by the supplier, with all required cables, ready for connection to the local AC electrical grid by a qualified electrician. Bidder to state supported input voltage, phase, frequency and current draw per unit, and the total simultaneous charging load for the quantity offered.
12 Electric protection, min IP54.
13 Battery charge indicator.
14 Operation hour meter.
15 Drive motor rating at short-time duty S2, 60 minutes (IEC 60034-1), kW, min 5.9. Bidder to state the duty type and rating period on which each motor power is quoted, supported by the manufacturer's published technical specification sheet. Where a rating other than the one specified is quoted, the equivalent value on the specified duty basis shall be stated.
16 Lift motor rating at S3 per IEC 60034-1, kW, min 9.5; bidder to state the cyclic duration factor.
17 Travel speed, laden/unladen, km/h, min 10/10.
18 Brakes: electromagnetic/hydraulic, plus parking brake and deadman/presence pedal.
19 Load wheels: non-marking polyurethane.
20 Battery cycle life, min 6,000 cycles at 80% depth of discharge (DoD), measured to an end-of-life criterion of 80% retained rated capacity, at 25 degrees C ambient and 1C charge/discharge rate. Bidder to submit the battery manufacturer's datasheet or pack label stating the cycle count. Where the datasheet does not state depth of discharge and end-of-life retention, the bidder shall confirm both in writing on manufacturer letterhead. A cycle life test report referencing IEC 62620 (or accredited third-party equivalent) shall be provided before delivery acceptance.
21 Battery management system (BMS) compliant with IEC 62619, logging cycle count, depth of discharge and state of health, retrievable by the operator or service technician.
22 Bidder to state battery weight (kg), removal/extraction method, and whether a lifting aid is required for battery removal and replacement.
23 Ambient operating conditions (base configuration): equipment rated for continuous operation in standard indoor warehouse conditions, ambient 0 degrees C to +40 degrees C. All prices in the main schedule are for this base configuration.
24 Reverse alarm, acoustic, mandatory.
25 Emergency stop button, mandatory, isolating drive and hydraulic power.
26 Key or pin-code access system for operator authorisation.
27 1 kg fire extinguisher, min.
28 Hygiene and GMP: Easy-to-clean design (smooth surfaces, minimal exposed wiring) to comply with Good Manufacturing Practice standards in medical/pharmaceutical warehouses.
29 Certifications: Equipment to possess CE marking (or equivalent)
30 Compliance with ISO 3691 (or equivalent recognised industrial truck safety standard, e.g. ANSI/ITSDF B56) required.
31 Certificate of Quality Management System according to ISO 9001 in the name of the manufacturer or equivalent certification. In case of ISO9001 the Certificate must be issued by an independent Certifying Body/Agency. If the legal manufacturer and the OEM / manufacturing facility are different entities, certificates must be provided for both.
32 Manufacturer Environmental management system: ISO 14001:2015 and/or equivalent certification and/or internal policy document issued by the Manufacturer related to environmental considerations of the company. If the legal manufacturer and the OEM / manufacturing facility are different entities, documentation covering the actual OEM manufacturing facility (or both) must be provided.
33 Manufacturer's authorization if the bidder is not the manufacturer
34 Owners/operators manual, English, French, Spanish or Arabic depending on destination country.
35 Battery end-of-life: Bidder to provide documentation on safe disposal/recycling of the battery at end-of-life, compliant with local and international hazardous waste regulations.
36 Warranty: Machinery and all accessories under warranty for a minimum of 1 year or 1,500 hours of operation, whichever occurs first. The warranty period shall commence on the date of successful completion of the relevant tests and/or inspections of the goods by UNOPS or the Consignee designated by UNOPS to the Contractor. A warranty certificate shall be provided with the delivery of the goods
37 Warranty Battery: minimum 6 years. The warranty period shall commence on the date of successful completion of the relevant tests and/or inspections of the goods by UNOPS or the Consignee designated by UNOPS to the Contractor. A warranty certificate shall be provided with the delivery of the goods
38 Bidders shall demonstrate an authorised distributor network with full warranty and after-sales service in at least 5 countries of the Africa region, and minimum 3 countries in Asia. Bidders shall submit a list of distributors with names and contact details. The nominated local distributor shall be responsible for warranty and repair of the base item and all additional equipment provided with each item. Failure to demonstrate the required extent of coverage with full warranty and after-sales service will exclude the bidder from further evaluation.
DESIRABLE OPTIONS, PRICED SEPARATELY: Please enter further available options as applicable. If Standard, state "Standard".
39 Repair manual in one or more of English, Spanish, French, Arabic, please indicate.
40 Spare parts kit, 1 year / 1,500 hours of operation, min.
41 Integrated barcode scanner/computer terminal mounting.
42 Alternative Lithium-ion (Li-ion/LFP) Battery Options (e.g. other capacities in kWh)
43 Battery end-of-life: Manufacturer-supported take-back/recycling programme.
44 Mechanical rail guidance system (chassis guide rollers): Bidder to state achieved working aisle width (max 1,930 mm), guide roller dimensions, required rail gauge/clearance, and transfer aisle width
45 Wire/inductive guidance system (on-board sensors & steering controller): Bidder to state achieved working aisle width (max 1,930 mm), wire frequency/compatibility, guidance tolerance, and transfer aisle width. Bidder to provide full pre-installation technical requirements.
45a On-truck guidance equipment: On-board sensors and steering controller fitted to the truck. Priced per truck.
45b Frequency generator: Stationary line driver/frequency generator unit to energize the floor wire loop. Priced per unit.
45c Floor wire installation: Floor slot cutting, wire laying, joint sealing, and commissioning. Bidder to state floor requirements before installation. Floor repair or levelling is excluded. Priced per linear meter of aisle.
46 Cold chain configuration: equipment rated for continuous operation in cold storage down to -20 degrees C, comprising anti-condensation protection for electrical and electronic assemblies, low-temperature-rated hydraulic oil, cold-rated seals and wheels, battery self-heating with BMS low-temperature charge inhibit, and operator heating where an enclosed or seated operator position exists. To be quoted as a separate unit price and not included in the base price.
47 Higher-output charger (e.g. a three-phase 400 V charger) - Bidder to define
48 Extended Warranty for 1 year or 3,000 hours of operation, whichever comes first
49 Extended Warranty for 1 year for the battery
Lot 15: Tow Tractor, Light Duty Tow
Towing capacity 1.5 to 3.0 ton, horizontal transport
Name and physical address of actual Manufacturing site(s):
Country of origin:
Product Website:
Item UNOPS Minimum Technical Requirement Complies (Yes / No) Offered Technical Specifications Support for Technical Compliance
1 Propellant, electric.
2 Towing capacity, ton, min 1.5
3 Turning circle and corridor width: bidder to state the turning radius, measured from the centre of rotation to the outermost point of the unit at full lock, and the minimum corridor width required for the unit, and for the full train where applicable.
4 Drawbar pull, measured at the coupling: rated (S2 60 min) min 800 N; maximum short-time (S2 5 min) min 3,000 N. Bidder to state both values and the duty rating basis used.
5 Operator position: sit-down or stand-on; bidder to specify.
6 Coupling/hitch: automatic or pin-type, compatible with standard tow-train trailer hitches; bidder to specify and confirm compatibility with Lot 17 trailers/carts if offered. Coupling height shall be adjustable to cover at least 250 mm to 400 mm above floor level. Bidder to state the pin diameter and the adjustable height range.
7 Battery type: Lithium Iron Phosphate (Li-ion / LFP). Other lithium chemistries (NMC, NCA, LTO) and lead-acid batteries are not acceptable.
8 Battery capacity, kWh, min 8
9 Battery charger: wall-mounted AC charger, single-phase 220 to 240 V 50 Hz, maximum AC input current 32 A, rated output approx. 6.0 to 6.6 kW, supplied, fitted and commissioned by the supplier, with all required cables, ready for connection to the local AC electrical grid by a qualified electrician. Bidder to state supported input voltage, phase, frequency and current draw per unit, and the total simultaneous charging load for the quantity offered.
10 Electric protection, min IP54.
11 Battery charge indicator.
12 Operation hour meter.
13 Drive motor rating at short-time duty S2, 60 minutes (IEC 60034-1), kW; bidder to state. Bidder to state the duty type and rating period on which each motor power is quoted, supported by the manufacturer's published technical specification sheet. Where a rating other than the one specified is quoted, the equivalent value on the specified duty basis shall be stated.
14 Travel speed, laden/unladen, km/h, min 7.5/8.
15 Gradeability, min 8%, towing a trailer train at the offered rated towing capacity (up to 3.0 t) using the maximum short-time drawbar pull. Bidder to state gradeability laden and unladen and provide the manufacturer's gradeability diagram.
16 Brakes, with regenerative braking, plus parking brake.
17 Working lights, front and rear, and acoustic horn.
18 Non-marking tyres.
19 Battery cycle life, min 6,000 cycles at 80% depth of discharge (DoD), measured to an end-of-life criterion of 80% retained rated capacity, at 25 degrees C ambient and 1C charge/discharge rate. Bidder to submit the battery manufacturer's datasheet or pack label stating the cycle count. Where the datasheet does not state depth of discharge and end-of-life retention, the bidder shall confirm both in writing on manufacturer letterhead. A cycle life test report referencing IEC 62620 (or accredited third-party equivalent) shall be provided before delivery acceptance.
20 Battery management system (BMS) compliant with IEC 62619, logging cycle count, depth of discharge and state of health, retrievable by the operator or service technician.
21 Bidder to state battery weight (kg), removal/extraction method, and whether a lifting aid is required for battery removal and replacement.
22 Ambient operating conditions (base configuration): equipment rated for continuous operation indoors, semi-outdoors and outdoors, ambient 0 degrees C to +50 degrees C, with solar and dust exposure protection, UV-resistant finishes and seals, and min IP54 on electrical enclosures. All prices in the main schedule are for this base configuration.
23 Reverse alarm, acoustic, mandatory.
24 Anti-roll-back system preventing roll-back on inclines.
25 Emergency stop button, mandatory, isolating drive power.
26 Key or pin-code access system for operator authorisation.
27 1 kg fire extinguisher, min.
28 LED floor warning spotlight projecting a red or blue spot onto the floor ahead of or behind the machine to warn pedestrians and oncoming equipment.
29 Hygiene and GMP: Easy-to-clean design (smooth surfaces, minimal exposed wiring) to comply with Good Manufacturing Practice standards in medical/pharmaceutical warehouses.
30 Certifications: Equipment to possess CE marking (or equivalent)
31 Compliance with ISO 3691 (or equivalent recognised industrial truck safety standard, e.g. ANSI/ITSDF B56) required.
32 Certificate of Quality Management System according to ISO 9001 in the name of the manufacturer or equivalent certification. In case of ISO9001 the Certificate must be issued by an independent Certifying Body/Agency. If the legal manufacturer and the OEM / manufacturing facility are different entities, certificates must be provided for both.
33 Manufacturer Environmental management system: ISO 14001:2015 and/or equivalent certification and/or internal policy document issued by the Manufacturer related to environmental considerations of the company. If the legal manufacturer and the OEM / manufacturing facility are different entities, documentation covering the actual OEM manufacturing facility (or both) must be provided.
34 Manufacturer's authorization if the bidder is not the manufacturer
35 Owners/operators manual, English, French, Spanish or Arabic depending on destination country.
36 Battery end-of-life: Bidder to provide documentation on safe disposal/recycling of the battery at end-of-life, compliant with local and international hazardous waste regulations.
37 Warranty: Machinery and all accessories under warranty for a minimum of 1 year or 1,500 hours of operation, whichever occurs first. The warranty period shall commence on the date of successful completion of the relevant tests and/or inspections of the goods by UNOPS or the Consignee designated by UNOPS to the Contractor. A warranty certificate shall be provided with the delivery of the goods
38 Warranty Battery: minimum 6 years. The warranty period shall commence on the date of successful completion of the relevant tests and/or inspections of the goods by UNOPS or the Consignee designated by UNOPS to the Contractor. A warranty certificate shall be provided with the delivery of the goods
39 Bidders shall demonstrate an authorised distributor network with full warranty and after-sales service in at least 5 countries of the Africa region, and minimum 3 countries in Asia. Bidders shall submit a list of distributors with names and contact details. The nominated local distributor shall be responsible for warranty and repair of the base item and all additional equipment provided with each item. Failure to demonstrate the required extent of coverage with full warranty and after-sales service will exclude the bidder from further evaluation.
DESIRABLE OPTIONS, PRICED SEPARATELY: Please enter further available options as applicable. If Standard, state "Standard".
40 Repair manual in one or more of English, Spanish, French, Arabic, please indicate.
41 Electric rotating beacon/flashing beacon.
42 Spare parts kit, 1 year / 1,500 hours of operation, min.
43 Secondary hitch point for multi-trailer (train) configuration.
44 Alternative Lithium-ion (Li-ion/LFP) Battery Options (e.g. other capacities in kWh)
45 Battery end-of-life: Manufacturer-supported take-back/recycling programme.
46 Cold chain configuration: equipment rated for continuous operation in cold storage down to -20 degrees C, comprising anti-condensation protection for electrical and electronic assemblies, low-temperature-rated hydraulic oil, cold-rated seals and wheels, battery self-heating with BMS low-temperature charge inhibit, and operator heating where an enclosed or seated operator position exists. Bidder to state the operating temperature range of camera, monitor and fork laser where fitted. To be quoted as a separate unit price and not included in the base price.
47 Higher-output charger (e.g. a three-phase 400 V charger) - Bidder to define
48 Extended Warranty for 1 year or 3,000 hours of operation, whichever comes first
49 Extended Warranty for 1 year for the battery
Lot 16: Tow Tractor, Medium Duty Tow
Towing capacity 3.0 ton, horizontal transport
Name and physical address of actual Manufacturing site(s):
Country of origin:
Product Website:
Item UNOPS Minimum Technical Requirement Complies (Yes / No) Offered Technical Specifications Support for Technical Compliance
1 Propellant, electric.
2 Towing capacity, ton, min 3.0
3 Turning circle and corridor width: bidder to state the turning radius, measured from the centre of rotation to the outermost point of the unit at full lock, and the minimum corridor width required for the unit, and for the full train where applicable.
4 Drawbar pull, measured at the coupling: rated (S2 60 min) min 1,200 N; maximum short-time (S2 5 min) min 3,000 N and not less than 0.98 N per kg of offered rated towing capacity (e.g. 4,900 N for 5,000 kg). Bidder to state both values and the duty rating basis used.
5 Operator position: sit-down, with seat and overhead guard.
6 Coupling/hitch: automatic or pin-type, compatible with standard tow-train trailer hitches; bidder to specify and confirm compatibility with Lot 17 trailers/carts if offered. Coupling height shall be adjustable to cover at least 250 mm to 400 mm above floor level. Bidder to state the pin diameter and the adjustable height range.
7 Multi-trailer (train) towing capability, minimum 3 trailers in sequence; bidder to confirm rated train length.
8 Battery type: Lithium Iron Phosphate (Li-ion / LFP). Other lithium chemistries (NMC, NCA, LTO) and lead-acid batteries are not acceptable.
9 Battery capacity, kWh, min 15
10 Battery charger: wall-mounted AC charger, single-phase 220 to 240 V 50 Hz, maximum AC input current 32 A, rated output approx. 6.0 to 6.6 kW, supplied, fitted and commissioned by the supplier, with all required cables, ready for connection to the local AC electrical grid by a qualified electrician. Bidder to state supported input voltage, phase, frequency and current draw per unit, and the total simultaneous charging load for the quantity offered.
11 Electric protection, min IP54.
12 Battery charge indicator.
13 Operation hour meter.
14 Drive motor rating at short-time duty S2, 60 minutes (IEC 60034-1), kW; bidder to state. Bidder to state the duty type and rating period on which each motor power is quoted, supported by the manufacturer's published technical specification sheet. Where a rating other than the one specified is quoted, the equivalent value on the specified duty basis shall be stated.
15 Travel speed, laden/unladen, km/h, min 10/14.
16 Gradeability, min 8%, towing a trailer train at the offered rated towing capacity using the maximum short-time drawbar pull. Bidder to state gradeability laden and unladen and provide the manufacturer's gradeability diagram.
17 Brakes, with regenerative braking, plus parking brake.
18 Working lights, front and rear, mirrors, and acoustic horn.
19 Non-marking tyres.
20 Battery cycle life, min 6,000 cycles at 80% depth of discharge (DoD), measured to an end-of-life criterion of 80% retained rated capacity, at 25 degrees C ambient and 1C charge/discharge rate. Bidder to submit the battery manufacturer's datasheet or pack label stating the cycle count. Where the datasheet does not state depth of discharge and end-of-life retention, the bidder shall confirm both in writing on manufacturer letterhead. A cycle life test report referencing IEC 62620 (or accredited third-party equivalent) shall be provided before delivery acceptance.
21 Battery management system (BMS) compliant with IEC 62619, logging cycle count, depth of discharge and state of health, retrievable by the operator or service technician.
22 Bidder to state battery weight (kg), removal/extraction method, and whether a lifting aid is required for battery removal and replacement.
23 Ambient operating conditions (base configuration): equipment rated for continuous operation indoors, semi-outdoors and outdoors, ambient 0 degrees C to +50 degrees C, with solar and dust exposure protection, UV-resistant finishes and seals, and min IP54 on electrical enclosures. All prices in the main schedule are for this base configuration.
24 Seat belt for the operator, mandatory.
25 Reverse alarm, acoustic, mandatory.
26 Anti-roll-back system preventing roll-back on inclines.
27 Emergency stop button, mandatory, isolating drive power.
28 Key or pin-code access system for operator authorisation.
29 1 kg fire extinguisher, min.
30 LED floor warning spotlight projecting a red or blue spot onto the floor ahead of or behind the machine to warn pedestrians and oncoming equipment.
31 Hygiene and GMP: Easy-to-clean design (smooth surfaces, minimal exposed wiring) to comply with Good Manufacturing Practice standards in medical/pharmaceutical warehouses.
32 Certifications: Equipment to possess CE marking (or equivalent)
33 Compliance with ISO 3691 (or equivalent recognised industrial truck safety standard, e.g. ANSI/ITSDF B56) required.
34 Certificate of Quality Management System according to ISO 9001 in the name of the manufacturer or equivalent certification. In case of ISO9001 the Certificate must be issued by an independent Certifying Body/Agency. If the legal manufacturer and the OEM / manufacturing facility are different entities, certificates must be provided for both.
35 Manufacturer Environmental management system: ISO 14001:2015 and/or equivalent certification and/or internal policy document issued by the Manufacturer related to environmental considerations of the company. If the legal manufacturer and the OEM / manufacturing facility are different entities, documentation covering the actual OEM manufacturing facility (or both) must be provided.
36 Manufacturer's authorization if the bidder is not the manufacturer
37 Owners/operators manual, English, French, Spanish or Arabic depending on destination country.
38 Battery end-of-life: Bidder to provide documentation on safe disposal/recycling of the battery at end-of-life, compliant with local and international hazardous waste regulations.
39 Warranty: Machinery and all accessories under warranty for a minimum of 1 year or 1,500 hours of operation, whichever occurs first. The warranty period shall commence on the date of successful completion of the relevant tests and/or inspections of the goods by UNOPS or the Consignee designated by UNOPS to the Contractor. A warranty certificate shall be provided with the delivery of the goods
40 Warranty Battery: minimum 6 years. The warranty period shall commence on the date of successful completion of the relevant tests and/or inspections of the goods by UNOPS or the Consignee designated by UNOPS to the Contractor. A warranty certificate shall be provided with the delivery of the goods
41 Bidders shall demonstrate an authorised distributor network with full warranty and after-sales service in at least 5 countries of the Africa region, and minimum 3 countries in Asia. Bidders shall submit a list of distributors with names and contact details. The nominated local distributor shall be responsible for warranty and repair of the base item and all additional equipment provided with each item. Failure to demonstrate the required extent of coverage with full warranty and after-sales service will exclude the bidder from further evaluation.
DESIRABLE OPTIONS, PRICED SEPARATELY: Please enter further available options as applicable. If Standard, state "Standard".
42 Repair manual in one or more of English, Spanish, French, Arabic, please indicate.
43 Electric rotating beacon/flashing beacon.
44 Spare parts kit, 1 year / 1,500 hours of operation, min.
45 Alternative Lithium-ion (Li-ion/LFP) Battery Options (e.g. other capacities in kWh)
46 Battery end-of-life: Manufacturer-supported take-back/recycling programme.
47 Cold chain configuration: equipment rated for continuous operation in cold storage down to -20 degrees C, comprising anti-condensation protection for electrical and electronic assemblies, low-temperature-rated hydraulic oil, cold-rated seals and wheels, battery self-heating with BMS low-temperature charge inhibit, and operator heating where an enclosed or seated operator position exists. Bidder to state the operating temperature range of camera, monitor and fork laser where fitted. To be quoted as a separate unit price and not included in the base price.
48 Higher-output charger (e.g. a three-phase 400 V charger) - Bidder to define
49 Extended Warranty for 1 year or 3,000 hours of operation, whichever comes first
50 Extended Warranty for 1 year for the battery
Lot 17: Trailers / Carts (towed equipment)
Different type and capacity trolleys
Name and physical address of actual Manufacturing site(s):
Country of origin:
Product Website:
Item UNOPS Minimum Technical Requirement Complies (Yes / No) Offered Technical Specifications Support for Technical Compliance
1 Propellant: N/A (towed equipment).
2 Type: flatbed/platform trailer
3 Capacity per unit, ton, min 1
4 Turning circle and corridor width: bidder to state the turning radius, measured from the centre of rotation to the outermost point of the unit at full lock, and the minimum corridor width required for the unit, and for the full train where applicable.
5 Coupling: pin-type or automatic coupling, bidder to specify compatibility with the tow tractor hitch, if offered under Lot 15 or Lot 16. The drawbar eye height shall be adjustable to cover at least 250 mm to 400 mm above floor level. Bidder to state the coupling type, the drawbar eye inner diameter, the adjustable height range and the maximum permitted towing speed (min 16 km/h).
6 Wheels/castors: combination of swivel and fixed, load-rated, non-marking.
7 Braking: parking brake or wheel chocks required for units above 1.5 t capacity.
8 Deck/frame construction: steel or equivalent, corrosion-resistant coating/finish.
9 Stacking or nesting capability for efficient empty-unit storage and return transport.
10 Ambient operating conditions (base configuration): equipment rated for continuous operation indoors, semi-outdoors and outdoors, ambient 0 degrees C to +50 degrees C, with UV-resistant finishes, corrosion-resistant fittings and sealed wheel bearings suitable for dust exposure. All prices in the main schedule are for this base configuration.
11 Hygiene and GMP: Easy-to-clean design (smooth surfaces) to comply with Good Manufacturing Practice standards in medical/pharmaceutical warehouses.
12 Certificate of Quality Management System according to ISO 9001 in the name of the manufacturer or equivalent certification. In case of ISO9001 the Certificate must be issued by an independent Certifying Body/Agency. If the legal manufacturer and the OEM / manufacturing facility are different entities, certificates must be provided for both.
13 Manufacturer Environmental management system: ISO 14001:2015 and/or equivalent certification and/or internal policy document issued by the Manufacturer related to environmental considerations of the company. If the legal manufacturer and the OEM / manufacturing facility are different entities, documentation covering the actual OEM manufacturing facility (or both) must be provided.
14 Manufacturer's authorization if the bidder is not the manufacturer
15 Owners/operators manual, English, French, Spanish or Arabic depending on destination country.
16 All machinery and accessories under warranty for a minimum of 1 year. The warranty period shall commence on the date of successful completion of the relevant tests and/or inspections of the goods by UNOPS or the Consignee designated by UNOPS to the Contractor. A warranty certificate shall be provided with the delivery of the goods
17 Bidders shall demonstrate an authorised distributor network with full warranty and after-sales service in at least 5 countries of the Africa region, and minimum 3 countries in Asia. Bidders shall submit a list of distributors with names and contact details. The nominated local distributor shall be responsible for warranty and repair of the base item and all additional equipment provided with each item. Failure to demonstrate the required extent of coverage with full warranty and after-sales service will exclude the bidder from further evaluation.
DESIRABLE OPTIONS, PRICED SEPARATELY: Please enter further available options as applicable. If Standard, state "Standard".
18 Type: roller-bed trailer for pallet loading-dock transfer
19 Type: mesh/cage trolley
20 High Capacity unit, ton, min 2
21 Removable mesh/cage sides for the flatbed/platform sub-type.
22 Tipping/dump mechanism for the cage sub-type.
23 Cold chain configuration: cold-rated wheels/castors, bearings, fasteners and deck/frame finish for continuous operation in cold storage down to -20 degrees C. To be quoted as a separate unit price and not included in the base price.
24 Extended Warranty for 1 year.
Lot 18: Electric Utility/Pick-up Vehicle, Light Utility
Payload capacity 0.4 to 0.7 ton, horizontal transport
Name and physical address of actual Manufacturing site(s):
Country of origin:
Product Website:
Item UNOPS Minimum Technical Requirement Complies (Yes / No) Offered Technical Specifications Support for Technical Compliance
1 Propellant, electric.
2 Payload/cargo capacity, ton, min 0.4
3 Turning circle and corridor width: bidder to state the turning radius, measured from the centre of rotation to the outermost point of the unit at full lock, and the minimum corridor width required for the unit, and for the full train where applicable.
4 Cargo deck: flatbed or drop-side; bidder to state deck dimensions.
5 Seating: minimum 1 operator; bidder to state total seating/passenger capacity if applicable.
6 Drive/steering: automotive-style steering wheel or tiller; bidder to specify.
7 Battery type: Lithium Iron Phosphate (Li-ion / LFP). Other lithium chemistries (NMC, NCA, LTO) and lead-acid batteries are not acceptable.
8 Battery capacity, kWh, min 8
9 Battery charger: wall-mounted AC charger, single-phase 220 to 240 V 50 Hz, maximum AC input current 32 A, rated output approx. 6.0 to 6.6 kW, supplied, fitted and commissioned by the supplier, with all required cables, ready for connection to the local AC electrical grid by a qualified electrician. Bidder to state supported input voltage, phase, frequency and current draw per unit, and the total simultaneous charging load for the quantity offered.
10 Electric protection, min IP54.
11 Battery charge indicator.
12 Operation hour meter.
13 Drive motor rating at short-time duty S2, 60 minutes (IEC 60034-1), kW; bidder to state. Bidder to state the duty type and rating period on which each motor power is quoted, supported by the manufacturer's published technical specification sheet. Where a rating other than the one specified is quoted, the equivalent value on the specified duty basis shall be stated.
14 Travel speed, km/h, min 15, max as appropriate for indoor/campus use; bidder to state.
15 Max. gradeability, %, min 10.
16 Brakes, hydraulic, plus parking brake.
17 Headlights, tail lights, turn indicators, and horn, suitable for use on internal campus roads.
18 Seatbelt(s) for operator and any passenger seating.
19 Secondary towing capacity for small carts/trailers (e.g. oxygen cylinder carts); bidder to state.
20 Tyres suitable for the intended indoor/outdoor use environment; bidder to specify. Non-marking.
21 Battery cycle life, min 6,000 cycles at 80% depth of discharge (DoD), measured to an end-of-life criterion of 80% retained rated capacity, at 25 degrees C ambient and 1C charge/discharge rate. Bidder to submit the battery manufacturer's datasheet or pack label stating the cycle count. Where the datasheet does not state depth of discharge and end-of-life retention, the bidder shall confirm both in writing on manufacturer letterhead. A cycle life test report referencing IEC 62620 (or accredited third-party equivalent) shall be provided before delivery acceptance.
22 Battery management system (BMS) compliant with IEC 62619, logging cycle count, depth of discharge and state of health, retrievable by the operator or service technician.
23 Bidder to state battery weight (kg), removal/extraction method, and whether a lifting aid is required for battery removal and replacement.
24 Ambient operating conditions (base configuration): equipment rated for continuous operation indoors, semi-outdoors and outdoors, ambient 0 degrees C to +50 degrees C, with solar and dust exposure protection, UV-resistant finishes and seals, and min IP54 on electrical enclosures. All prices in the main schedule are for this base configuration.
25 Reverse alarm, acoustic, mandatory.
26 Anti-roll-back system preventing roll-back on inclines.
27 Emergency stop button, mandatory, isolating drive power.
28 Key or pin-code access system for operator authorisation.
29 1 kg fire extinguisher, min.
30 Hygiene and GMP: Easy-to-clean design (smooth surfaces, minimal exposed wiring) to comply with Good Manufacturing Practice standards in medical/pharmaceutical warehouses.
31 Certifications: Equipment to possess CE marking (or equivalent)
32 Compliance with ISO 3691 (or equivalent recognised industrial truck safety standard, e.g. ANSI/ITSDF B56) required.
33 Certificate of Quality Management System according to ISO 9001 in the name of the manufacturer or equivalent certification. In case of ISO9001 the Certificate must be issued by an independent Certifying Body/Agency. If the legal manufacturer and the OEM / manufacturing facility are different entities, certificates must be provided for both.
34 Manufacturer Environmental management system: ISO 14001:2015 and/or equivalent certification and/or internal policy document issued by the Manufacturer related to environmental considerations of the company. If the legal manufacturer and the OEM / manufacturing facility are different entities, documentation covering the actual OEM manufacturing facility (or both) must be provided.
35 Manufacturer's authorization if the bidder is not the manufacturer
36 Owners/operators manual, English, French, Spanish or Arabic depending on destination country.
37 Battery end-of-life: Bidder to provide documentation on safe disposal/recycling of the battery at end-of-life, compliant with local and international hazardous waste regulations.
38 Warranty: Machinery and all accessories under warranty for a minimum of 1 year or 1,500 hours of operation, whichever occurs first. The warranty period shall commence on the date of successful completion of the relevant tests and/or inspections of the goods by UNOPS or the Consignee designated by UNOPS to the Contractor. A warranty certificate shall be provided with the delivery of the goods
39 Warranty Battery: minimum 6 years. The warranty period shall commence on the date of successful completion of the relevant tests and/or inspections of the goods by UNOPS or the Consignee designated by UNOPS to the Contractor. A warranty certificate shall be provided with the delivery of the goods
40 Bidders shall demonstrate an authorised distributor network with full warranty and after-sales service in at least 5 countries of the Africa region, and minimum 3 countries in Asia. Bidders shall submit a list of distributors with names and contact details. The nominated local distributor shall be responsible for warranty and repair of the base item and all additional equipment provided with each item. Failure to demonstrate the required extent of coverage with full warranty and after-sales service will exclude the bidder from further evaluation.
DESIRABLE OPTIONS, PRICED SEPARATELY: Please enter further available options as applicable. If Standard, state "Standard".
41 Repair manual in one or more of English, Spanish, French, Arabic, please indicate.
42 Electric rotating beacon/flashing beacon.
43 Lockable cargo box/security lid.
44 Spare parts kit, 1 year / 1,500 hours of operation, min.
45 Alternative Lithium-ion (Li-ion/LFP) Battery Options (e.g. other capacities in kWh)
46 Battery end-of-life: Manufacturer-supported take-back/recycling programme.
47 Higher-output charger (e.g. a three-phase 400 V charger) - Bidder to define
48 Extended Warranty for 1 year or 3,000 hours of operation, whichever comes first
49 Extended Warranty for 1 year for the battery
Lot 19: Electric Utility/Pick-up Vehicle, Medium Utility
Payload capacity min 0.7 ton, horizontal transport
Name and physical address of actual Manufacturing site(s):
Country of origin:
Product Website:
Item UNOPS Minimum Technical Requirement Complies (Yes / No) Offered Technical Specifications Support for Technical Compliance
1 Propellant, electric.
2 Payload/cargo capacity, ton, min 0.7
3 Cargo deck: flatbed or drop-side; bidder to state deck dimensions.
4 Seating: minimum 1 operator; bidder to state total seating/crew-cab capacity if applicable.
5 Drive/steering: automotive-style steering wheel.
6 Battery type: Lithium Iron Phosphate (Li-ion / LFP). Other lithium chemistries (NMC, NCA, LTO) and lead-acid batteries are not acceptable.
7 Battery capacity, kWh, min 12
8 Battery charger: wall-mounted AC charger, single-phase 220 to 240 V 50 Hz, maximum AC input current 32 A, rated output approx. 6.0 to 6.6 kW, supplied, fitted and commissioned by the supplier, with all required cables, ready for connection to the local AC electrical grid by a qualified electrician. Bidder to state supported input voltage, phase, frequency and current draw per unit, and the total simultaneous charging load for the quantity offered.
9 Electric protection, min IP54.
10 Battery charge indicator.
11 Operation hour meter.
12 Drive motor rating at short-time duty S2, 60 minutes (IEC 60034-1), kW; bidder to state. Bidder to state the duty type and rating period on which each motor power is quoted, supported by the manufacturer's published technical specification sheet. Where a rating other than the one specified is quoted, the equivalent value on the specified duty basis shall be stated.
13 Travel speed, km/h, min 15, max as appropriate for indoor/campus use; bidder to state.
14 Max. gradeability, %, min 10.
15 Brakes, hydraulic, plus parking brake.
16 Headlights, tail lights, turn indicators, mirrors, and horn, suitable for use on internal campus/inter-facility roads.
17 Seatbelt(s) for operator and any passenger/crew-cab seating.
18 Towing capacity for carts/trailers between adjacent facilities; bidder to state.
19 Turning circle and corridor width: bidder to state the turning radius, measured from the centre of rotation to the outermost point of the unit at full lock, and the minimum corridor width required for the unit, and for the full train where applicable.
20 Tyres suitable for the intended indoor/outdoor use environment; bidder to specify. Non-marking.
21 Battery cycle life, min 6,000 cycles at 80% depth of discharge (DoD), measured to an end-of-life criterion of 80% retained rated capacity, at 25 degrees C ambient and 1C charge/discharge rate. Bidder to submit the battery manufacturer's datasheet or pack label stating the cycle count. Where the datasheet does not state depth of discharge and end-of-life retention, the bidder shall confirm both in writing on manufacturer letterhead. A cycle life test report referencing IEC 62620 (or accredited third-party equivalent) shall be provided before delivery acceptance.
22 Battery management system (BMS) compliant with IEC 62619, logging cycle count, depth of discharge and state of health, retrievable by the operator or service technician.
23 Bidder to state battery weight (kg), removal/extraction method, and whether a lifting aid is required for battery removal and replacement.
24 Ambient operating conditions (base configuration): equipment rated for continuous operation indoors, semi-outdoors and outdoors, ambient 0 degrees C to +50 degrees C, with solar and dust exposure protection, UV-resistant finishes and seals, and min IP54 on electrical enclosures. All prices in the main schedule are for this base configuration.
25 Reverse alarm, acoustic, mandatory.
26 Anti-roll-back system preventing roll-back on inclines.
27 Emergency stop button, mandatory, isolating drive power.
28 Key or pin-code access system for operator authorisation.
29 1 kg fire extinguisher, min.
30 Hygiene and GMP: Easy-to-clean design (smooth surfaces, minimal exposed wiring) to comply with Good Manufacturing Practice standards in medical/pharmaceutical warehouses.
31 Certifications: Equipment to possess CE marking (or equivalent)
32 Compliance with ISO 3691 (or equivalent recognised industrial truck safety standard, e.g. ANSI/ITSDF B56) required.
33 Certificate of Quality Management System according to ISO 9001 in the name of the manufacturer or equivalent certification. In case of ISO9001 the Certificate must be issued by an independent Certifying Body/Agency. If the legal manufacturer and the OEM / manufacturing facility are different entities, certificates must be provided for both.
34 Manufacturer Environmental management system: ISO 14001:2015 and/or equivalent certification and/or internal policy document issued by the Manufacturer related to environmental considerations of the company. If the legal manufacturer and the OEM / manufacturing facility are different entities, documentation covering the actual OEM manufacturing facility (or both) must be provided.
35 Manufacturer's authorization if the bidder is not the manufacturer
36 Owners/operators manual, English, French, Spanish or Arabic depending on destination country.
37 Battery end-of-life: Bidder to provide documentation on safe disposal/recycling of the battery at end-of-life, compliant with local and international hazardous waste regulations.
38 Warranty: Machinery and all accessories under warranty for a minimum of 1 year or 1,500 hours of operation, whichever occurs first. The warranty period shall commence on the date of successful completion of the relevant tests and/or inspections of the goods by UNOPS or the Consignee designated by UNOPS to the Contractor. A warranty certificate shall be provided with the delivery of the goods
39 Warranty Battery: minimum 6 years. The warranty period shall commence on the date of successful completion of the relevant tests and/or inspections of the goods by UNOPS or the Consignee designated by UNOPS to the Contractor. A warranty certificate shall be provided with the delivery of the goods
40 Bidders shall demonstrate an authorised distributor network with full warranty and after-sales service in at least 5 countries of the Africa region, and minimum 3 countries in Asia. Bidders shall submit a list of distributors with names and contact details. The nominated local distributor shall be responsible for warranty and repair of the base item and all additional equipment provided with each item. Failure to demonstrate the required extent of coverage with full warranty and after-sales service will exclude the bidder from further evaluation.
DESIRABLE OPTIONS, PRICED SEPARATELY: Please enter further available options as applicable. If Standard, state "Standard".
41 Repair manual in one or more of English, Spanish, French, Arabic, please indicate.
42 Electric rotating beacon/flashing beacon.
43 Lockable cargo box/security lid.
44 Spare parts kit, 1 year / 1,500 hours of operation, min.
45 Alternative Lithium-ion (Li-ion/LFP) Battery Options (e.g. other capacities in kWh)
46 Battery end-of-life: Manufacturer-supported take-back/recycling programme.
47 Higher-output charger (e.g. a three-phase 400 V charger) - Bidder to define
48 Extended Warranty for 1 year or 3,000 hours of operation, whichever comes first
49 Extended Warranty for 1 year for the battery
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
1 ITB_Section_I_Instructions to Bidders.pdf
Bidding document • 0.28 MB
2 ITB_Section_II_Schedule of Requirements_ITB_2026_64524_v00.docx
Bidding document • 0.49 MB
3 ITB_Section_III_Returnable Bidding Forms_ITB_2026_64524_v00.docx
Bidding document • 1.24 MB
4 ITB_Section_IV_Contract Forms.docx
Bidding document • 0.31 MB
5 Sample Long_term_agreement.docx
Bidding document • 0.03 MB
6 ITB_Form C_Price Schedule Form_ITB_2026_64524_v00.xlsx
Bidding document • 0.10 MB
7 ITB_Form D_Technical Bid Form_ITB_2026_64524_v00.xlsx
Bidding document • 0.15 MB
Notice on UNGM.html
Notice page • 0.04 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .