Providing Lift Arrangements in OP block at Mundiyampakkam GH in Villupuram District

Design, Engineering, renewal by supply, Fabrication, Erection, Testing, commissioning and handing over of 1 No 20 persons Capacity Gearless Passenger cum Bed lift with machine room as per the following Technical specifications. Technical Specifications: 1.Location: Government Villupuram Medical College Hospital OP Block. 2.No of lift: 1 No 3.Type of lift: Passenger cum bed lift. (1768 Kgs) 4.Capacity of lift: 20 persons capacity Gearless passenger cum bed lift 5.Speed: 1.0 M / sec 6.Type of drive: Specific variable voltage variable frequency V3F drive with enhanced ride comfort and near Zero levelling functions. 7.No of floors: 2 (Ground + 1 Floor) 8.Total travel: 7.0 Mtrs Travel 9.Leveling accuracy: High level accuracy with smooth & jerk free stopping 10. Construction of Car: 18SWG High quality S.S 304 Grade car neat hairline finish, S.S. hand rail, S.S. floor line finish, Perspex false ceiling, stretcher impact protection. 11. Position of machine: Directly above the lift well. 12. No. of landing entrance: One in front - 4 Nos 13. No. of car entrance: one in the front only 14. Car entrance door: power operated V3F drive side opening sliding 18SWG stainless steel hariline finish. 15. Landing entrance door: power operated V3F sliding, opening 18SWG stainless steel hairline finish with provision for emergency key. 16.Lift well existing: 3000mm X 3000mm 17.Lift pit depth available : 2000 mm 18.Car (Clear inside): 1300mm (wide) X 2400mm (Depth) 19.Car Clear opening: 1500mm width X 2800mm height.

35. Provision of intercom with phone: To be provided by the lift contractor 3 points EPABX system at three places vide 1) inside the car 2) Head room 3) at ground floor attender room. 36.Lift License: Preparation of Drawing, payment of charges to CEIG and insurance policies if any and obtaining CEIG safety certificate as per lift act should be done by the lift contractor. 37. Floor announciator with music, included. 38.Special features a. Infra red door sensor with full height screen. b. Tubular S.S hand rail in cars. c. Voltage stabilizer for circuit control. d. Stainless steel signal fixtures. e. Vendal proof S.S. Button with S.S. cover. f. S.S. hairline finish door frames for landing doors. g. VF door Register signal. h. Call register signal. i. Stainless steel facia plate for car operating panel and landing fixtures. j. Steel ladder for machine room and ladder for lift shaft pit. k. On - Off switch for fan and light. l. Over load warning indicator with audio announcement. m.Fall width half height rear panel mirror.

39.Provision of architraves covering all three sides upto a width of 300 decorum sheet of plywood with TW frame with aluminium beading architraves should also cover the thickness of still level door frame at the landing and indicator boxes at all landings. 40. Other standard features: Voltage stabilizer for control units, Over speed governor, phase failure and phase reversal relay alarm bell, T-Guide brackets for car and counter weight, rubber padding under winding unit, motor of adequate capacity, single reduction worm gear, electromagnetic brake with compression springs car safety gears buffer, electro mechanical door locks emergency key side supporting angles, motor over load protection devices final limits switch, main suspension ropes counter weights lifting hoist for mounting the machineries. 41.Guarantee: Guarantee for the materials workmanship of equipments complete should be offered by lift firm for a period not less than one year. 41. Site testing in accordance with IS 14665 should be carried out at the time of handing over. Necessary spares and tools required for the maintenance for a period of one year. 42. Supply operation and maintenance manual with necessary tools for operation. The list of tools required should be detailed by the contractor in a separate sheet duly signed by the contractor. (Johnson / KONE / Equivalent)

Supply and fixing of 45 KVA capacity three phase microprocessor controlled air cooled unbalanced electronic servo voltage stabilizer with Input Volts 29V-465V Output Volts 400V, Voltage Regulation of ±1%, Output Volt Adjust 395V- 405V, Input Frequency, 47 Hz-52Hz, Output Frequency 50 Hz± 0.5%, Voltage Correction - 35V/Sec, with LCD Display for Input and Voltage Reading high / low voltage cut off and single phase preventor and with manual bypass arrangements for lift unit.

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (5 points / Coil) Higher End

Supply and fixing of single box type 4' 18 W LED fitting complete with TW round blocks on wall or ceiling with 18 W LED tube light crystal glass connection ( Havells / equivalant) with PVC unsheathed Copper leads from terminals to the fitting.

Supply and fixing of WT bulk head fitting with guard suitable for 15 W LED Bulb.

Supply and fixing of 48W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with 1 no.32 mm dia GI bend complete on the existing post / on wall with PVC unsheathed FRLS copper leads with MS clamps and with painting.

Supply and fixing of 1200mm (48") sweep AC ceiling fan High speed complete with 2 module 100W fan step regulator (Higher end) with 300 mm down rod with on the existing fan clamp.

Supply and fixing of 1 no.6A two module 3 pin socket , 1 no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and Run of 2 of 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection of 2.5 sq.mm copper wire and making good of the concealed portion.

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) 1 No. 32A DP MCB as incoming and 6 Nos. 6A to 32A SP MCB outgoing in flush with wall and making good of the concealed portion with earth connection only. The MCB DB and MCB's should be with ISI mark (like standard make)

Supply and Run of 2 of 6 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection of 6 sq.mm copper wire and making good of the concealed portion with suitable colour.

Supply and fixing of Vertical type 4 way Triple pole and neutral MCB Distribution board double door type with 125 A 4 pole MCCB as incoming 1 No. 63A TP MCB and 9 Nos. 32A SP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection only. The MCB DB and MCB's should be Like Craftree / equivalent.

Supply and fixing of 63A FP MCB switch on suitable angle iron frame work with MS cable entry box with earth connection only.

Supply and run of 4 of 10 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 10 sq.mm copper wire and making good of the concealed position.

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry.

Supply and Run of 2 of Nos. 8 SWG copper wire in suitable PVC rigid pipe on wall and ceiling for earth connection.