GES U 21 2022 23 PROVN OF STORE ROOM AND VEH PARKING SHED AT ASCON NODE OF SUB GP AT UDHAMPUR GALVALUME ROOF SHEET FALSE CEILING AND OTHER ALLIED WORKS IN BLDG NO NP 07 HQ OFFICE AT HQ 1 EW BDE DOUBLE ENTRY SLIDING GATE AT MAIN GATE OF

Amount

Surface dressing not exceeding 15 cm deep in hard/dense soil complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 M wide and not exceeding 1.5 M in depth for foundation complete all as specified and as directed.

Anti-termite treatment of bottom and sides of excavation at the rate of 5 ltr of emulsion per square metre of surface area complete all as specified and as directed.

Anti-termite treatment of the top surface of filled earth at the rate of 5 ltr of emulsion per square metre of surface complete all as specified and as directed.

Anti-termite treatment of the soil under plinth protection at the rate of 5 ltr of emulsion per square metre of surface complete all as specified and as directed.

Returning filling in including spreading levelling watering and well ramming in layers not exceeding 25 cm complete all as specified and as directed.

Removing excavated soil to a distance exceeding 50 m and not exceeding 1.50 km out side defence land complete all as specified and as directed.

PCC 1:4:8 type C-2 (using 40 mm graded crushed stone aggregates) as in foundation filling and mass concrete complete all as specified and as directed.

Reinforced cement concrete (nominal mix) type B-1 1:2:4 (using 20 mm graded crushed stone aggregates) using footing, foundation beams, plinth beam, roof beam, lintel band and similr work etccomplete all as specified and as directed.

Reinforced cement concrete (nominal mix) type B-1 1:2:4 (using 20 mm graded crushed stone aggregates) using columns, pillars and similar work etc. complete all as specified and as directed.

RCC type B-1 1:1 1/2:3 (using 20 mm graded crushed stone aggregates) for slabs supported on walls beams and columns in floors, roof, landing, balconies, canopies slabs and in shelves and the like complete all as specified and as directed.

RCC type B-1 1:1 1/2:3 (using 20 mm graded crushed stone aggregates) for chajjas complete all as specified and as directed.

Form wotk to edges of concrete flat slats sides of RCC/PCC bands etc in walls horizental or slopping exceeding 10 cm but not exceeding 20 cm wide rough finished surfaces complete all as specified and as directed.

Form work to soffits of suspended slabs such as roof slabs, landing and similar work not exceeding 200 mm thick complete all as specified and as directed.

Form work to chullahah hoods chajjas, trought and similar items rough finished surfaces of concrete complete all as specified and as directed.

Form work to sides and soffit of floor or roof beams, lintels beam, coloumn and similar work etc complete all as specified and as directed.

Mild steel TMT bars 8 mm dia and over and over cut to length bent to shape required including cranking, bending spirally including mild steel wire not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

Mild steel bars 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and binder TMT bars cut to length bent to shape required including cranking, bending spirally including mild steel wire not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

Brick work with sub class 'B' brick, straight or curved on plan exceeding 6 M Mean radius built in type CM 1:6 complete all as specified and as directed.

Rendering 15 mm thick in CM 1:6 on brick work and finished even and smooth without using extra cement complete all as specified and as directed.

Rendering 15 mm thick in CM 1:4 on brick work and finished even and smooth without using extra cement complete all as specified and as directed.

Rendering 5 mm thick in CM 1:3 on ceiling and exposed surface of concrete finsihed even and smooth without using extra cement complete all as specified and directed.

New plaster surface of walls and applying two coat of oil bound distempers over one coat of primer and two coats of wall care putty complete all as specified and as directed.

Preparation of new plaster surfaces applying two coats of cement base paint and over one coat of primers complete all as specified and directed.

Preparation of new plaster surfaces applying three coats of white wash on ceiling complete all as specified and directed.

Hard core of guage not exceeding 63 mm deposited spread and levelled in layers not exceeding 15 cm thick watered and rammed to a true surface complete all as specified and directed.

75 mm thick PCC 1:4:8 type B-2 (using 40 mm graded crushed stone aggregates) as in sub base of floor etc. complete all as specified and directed.

15 mm thick screed bed in cement mortar 1:6 for laying floor finishes under floor complete all as specified and directed.

Machine cut kota stone slab flooring 18-20 mm thick over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including 15 mm CM 1:4 complete all as specified and directed.

Rendering 10 mm thick on fair faces of brick work or concrete surface in CM 1:4 on vertical surfaces/backing coat complete all as specified and directed.

Machine cut kota stone 18-20 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Cement concrete 1:3:6 type C-1, 75 mm thick (using 20 mm graded crushed stone aggregates) as in plinth protection finished fair and even with using extra cement complete all as specified and directed.

Steel window (box type) factory made with side hung shutters including pintol hinges, steel handles, steel peg stay and all locking arrangement complete with glazing bars dovetailed or welded including one shop coat of red oxide primer complete all as specified and directed. Note : i) The window shall be fabricated as per Drg No CEUZ/TD/1269/2008 Sheet 1/3 to 3/3 ii) MS fillets, glazing, wire gauge shall be measured and paid separately.

Framed work such as grill, gratings etc with ends of bars shouldered and/or riveted or forged in to spikes, framed guard bars, barred iron doors ladders framed balusters and similar work conforming to Fe 290 Gde E-165 complete all as specified and directed.

Preparation of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed.

Sheet glass 3 mm thick ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in Each pane complete all as specified and directed.

105 x 60 mm pressed steel frames for doors with one or more rebate including necessary fixing lugs, hinges lock strike plate etc complete as specified including a coat of shop coat zinc chrome primer complete all as specified and directed.

Factory made 35 mm thick 2nd class hard wood, plain framed, paneled shutters (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both sides, the side of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated, 35 mm thick complete all as specified and as directed.

100 mm size mild steel butt hinges medium weight cold rolled complete all as specified and directed.

300 mm long aluminium alloy anodised sliding door bolt with hasp staple (bolt type) and fixing clips of sheets ,cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed.

Floor door stoper (140 mm length) of aluminium alloy body complete all as specified and directed.

150 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

150 mm length aluminium handles fabricated type anodised complete all as specified and directed.

Preparation of new wooden surfaces of any description, not other wise described over 10 cm width or girth applying two coats of synthetic enamel paint over a coat of primers complete all as specified and directed.

2nd class hardwood plain, solid straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, puttogether with glue pinned at joints, 2nd class HW complete all as specified and directed.

18/19 mm thick block board, grade 2 quality, interior grade, commercial type fixed with screws to timber frame work/iron frame work (Termite treated/water proof) complete all as specified and directed. Make : Green Ply/Kit ply.

0.9 mm thick decorative choice of lamination type-1 of surface finish, colour and pattern as approved adhesive as per manufacturers instructions complete all as specified and directed.

2nd class HW plain fillets squre, rectangular or triangular in section clean sawn, secured with nails or brads exceeding 3 Sqcm but not exceeding 6 Sqcm complete all as specified and directed.

Hasp & staple 100 mm size aluminium anodised fixed with screws complete all as specified and directed.

Stainless steel catcher of superior quality complete all as specified and as directed.

50 mm stain less steel pivoted type hinges of superior quality and complete all as specified and as directed.

75 mm long aluminium alloy handles, fabricated type, anodised (ISI Marked) all as approved and complete all as specified and directed by Engr-in-Charge.

Preparation of new/old surfaces of concrete surfaces by and brushing neat cement slurry @ 3 kg/Sqm including 20 mm thick plastering in CM (1:3) finished even and smooth mixed with water proofing compound (WPC shall be measured and paid separately). Applying bituminous primer on roof surfaces @ 0.40 ltr/Sqm and applying one coat of hot blown bitumen of grade 85/25 @ 1.20 Kg/Sqm and provide modified polymeric five layred APP (Atactic Polypropylene) Modified Polymeric Membrane with 100 micron high molecular high density polyethylene film. Min wt of membrane will be 3.5 Kg/Sqm and bonded completely to the surfaces with min end overlap of 15 cms and side lap 75 mm (overlaps to be bounded with thermo fused by flame) and over APP applying one coat of hot blown bitument 85/25 @ 1.2 Kg/Sqm blinded with fine sand in dry condition @ 0.5 Kg/Sqm & including two coats of bituminous Aluminium paint complete all as specified and as directed.

Supply only integral water proofing compound complete all as specified and directed.

110 mm PVC (SWR) pipes single socket in any length with rubber ring joints fixed to wall complete all as specified and directed.

110 mm PVC (SWR) bends any redius with access door complete all as specified and directed.

Excavation of post holes in soft and liise soil complete all as specified and directed.

Surface excavation not exceeding 30 cm deep and average 15 cm deep and getting out of soft and loose soil complete all as specified and directed.

MS rolled section Fe 410 W (Gde E-250) quality-B as in main and cross beams, hip and jack rafters, purlins where conneceted to common rafters and running rails and guides for sliding doors, fixed with angel cleats or other connecting plates as in vertical posts and perlins etc complete all as specified and as directed.

Pre-painted galvalume aluminum zinc coating GI bases corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/clading to wall, fixed with self tapping screws complete all as specified and directed.

Hand rails, half round or other stock section or core for wooden hand rail straight portion, drilled counter sunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof inclduing secuing bolts, posts and to shape as directed, drilling holes, notching for wire etc. flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting etc. and similar work confirming to Fe-290 Gde E-165 complete all as specified and as directed.

Cement concrete type B-2 1:2:4 (using 40 mm graded crushed stone aggregates) as in foundation filling of post complete all as specified and directed.

PCC 1:2:4 type B-2 (using 40 mm graded crushed stone aggregates) 100 mm thick as in paving complete all as specified and directed.

Forming 12 mm thick expendion joint in 150 mm thick concrete slab filled with preform bituminious filler and top 30 mm x prime and sealed with sealing compound, Grade 'A' complete all as specified and directed.

Moorum/red bajri filling in floors or pavings, laid in layers not exceeding 15 mm thick, spread, levelled and rammed including watering complete all as specified and directed.

PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in sub base and mass concrete 100 mm thick as in pavings complete all as specified and directed.

25 mm thick cement concrete 1:2:4 type B-0 as in floor finished even and fair complete all as specified and directed.

Screed bed or bedding layer of mortar 15 mm thick for laying floor tiles in CM 1:4 complete all as specified and directed.

Cement concrete rich coloured chequered tiles machine pressed with imported pigment finish (mirror/rough cast) of size 300 mm x 300 mm x (20 to 25 mm) thick set and jointed with neat cement slurry complete all as specified and directed.

Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, over 50 mm thick sand cushioning (Dazzle Pattern) M-35 Grade. ISI/RUCHI Ind/NITCO or equivalent as approved and complete all as specified and directed by Engr-in-Charge.

Dismantling AC corrugated sheet as in roof covering complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) or insulation boards any thickness including cover fillets complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provded for complete all as specified and directed.

Demolition cement concrete in ground floors and paving (unreinforced) not exceeding 15 cm thickness (below or above ground floor) complete all as specified and directed.

Demolition of Brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pilars etc but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed.

Angles for roof truss with purlin, rafter, struts and post and fixed with angle cleats or other connecting plates confirming to Gde Fe 410-0 or Fe-310-0 complete all as specified and directed.

Pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick crimpted/tapard at the external end slop of any colour having tansile strength 550 Mpa as in roof covering fixed with self tapping screws and caps etc. complete all as specified and directed.

Plain galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick in ridges, hips, valley gutters at the external end slop of any colour having tansile strength 550 Mpa as in roof(ridges) covering fixed with self tapping screws and caps etc complete all as specified and directed.

Mild steel screw bolt (machine made) 11 to 15 mm dia with hexagonal or square heads at one end and screw the other or screwed both end to be fitted with washers and one hexagonal or squre nut exceeding 10 cm and not exceeding 15 cm long complete all as specified and directed.

Preparation of new steel surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide chrome primer complete all as specified and directed.

4 mm thick AC board (designer ceiling) of size 600 mm x 600 mm panel confirming to IS 14862 type B category three including GI frame work with size of grid 605 mm x 605 mm for seanless ceiling comprises of GI perimeter including all accessories complete all as specified and directed. Make : Everest.

Taking down cement plaster on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Applying two coat birla wall care putty on new plastered on wall surfaces including preparation of surface by brooming down or steel wire brushing, scrapping down vegetation growth, efflorscent salts and trading with oil greasy spot complete all as specified and directed.

Two coats of distempar oil emulsion over a coat of primer including preparation of new plastered surfaces of walls complete all as specified and directed.

75 mm thick plain cement concrete, type C-2, (1:3:6) (using 40 mm graded crushed stone aggregates) as in plinth protection complete all as specified and directed.

Taking down frames with shutters (without taking off shutters from the frame) area not exceeding 1.5 Sqm Each including iron mongery complete all as specified and directed.

Taking down frames with shutters (without taking off shutters from the frame) area exceeding 1.5 Sqm but not exceeding 4 Sqm Each including iron mangery complete all as specified and directed.

Powder coated anodised aluminium frames for doors, windows, ventilators with one or more rebates including jointing cleats for fixing etc complete all as specified and directed.

Powder coated aluminium anodised window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary jointing cleat glazing clips, rubber packing, anodised aluminium snap beading screws etc. complete all as specified and directed.

Powder coated aluminium anodised door shutters, aluminium section weighing 0.55 kg/m including necessary jointing cleat glazing clips, rubber packing, anodised aluminium snap beading screws etc. complete all as specified and directed.

100 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

100 mm length aluminium handles fabricated type anodised complete all as specified and directed.

4 mm thick figured glass, pin head type and glazing complete in suares exceeding 0.50 sqm in each pane including glazing clis, rubber acking, powder coated aluminium snap beading, serews complete all as specified and directed.

Aluminium alloy wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminium staples complete all as specified and directed.

Floor door stoper (140 mm length) of aluminium alloy body complete all as specified and directed.

Brass mortice lock, vertical type, size 100 mm, 4 leaver complete all as specified and directed.

PCC (1:4:8) type D-2 (using 40 mm graded crushed stone aggregates) as in foundations and mass concrete complete all as specified and directed.

Mild steel TMT bars 6 to 8 mm dia as in reinforcement cut to length, bent to shae required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (anealed not less than 0.9 mm dia), in stirrups, spacers & binders complete all as specified and directed.

Mild steel TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and binding waith and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

Use & waste of form work to sides of footings, rough finished flat surfaces complete all as specified and directed.

Use & waste of form work to sides of columns etc. rough finished surfaces complete all as specified and directed.

RCC M 25 design mix, (using 20 mm graded crushed stone aggregates) as in footing complete all as specified and directed.

RCC M-25 design mix, (using 20 mm graded crushed stone aggregates) as in columns, pillars, piers, posts and struts complete all as specified and directed.

20 mm thick granite (of any type) tiles machine cut in skirting dado laid over cement screed and jointed with grey cement slurrry and pointed with admixture of pigment to match the shade of slabs, including grinding and polishing complete all as specified and directed.

Framed works as in gates of angle or other section with gusset plates, braces etc. to be prepared for hanging or slidingwith and including either hooks and hinges or steel hanging doors fittings complete drilled for fixing steel sheetings fixing as in running rails complete all as specified and directed.

Stainless steel as in plates, plain or chequered fixed to steel gates complete all as specified and directed.

Frictionless rollers fixed at bottom of the steel gate, ball bearing socket type suitable for heavy steel gates complete all as specified and directed.

Stainless steel for gate/railling post or struts in fencing fixed independently including cutting and bending to shape as directed drilling holes, notching for wire etc. complete all as specified and directed.

Framed work such as grills, gratings etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars and similar work confirming to E-250 complete all as specified and as directed.

Mild steel confirming to grade Fe-165 (Fe-290) angle post or struts in fencing fixed independently including cutting and bending to shape as directed drilling holes, notching for wire etc. complete all as specified and as directed.

Applying two coats of cement based paint over a coat of chalk whiting including preparation of new plastered surfaces complete all as specified and as directed.

Galvanised 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of post including securing and tying at crossing with and provision of galvanised mild steel wire staple or steel pins etc complete all as specified and as directed. (Each line wire to be mesured)

Form work to sides of concrete foundation, footing, beams of columns, rafts, and rafts beams, sides of soffits, (if any) of foundation and plinth beams and similar work vertical or to batter all as specified for rough finished surface of concrete flat complete all as specified and as directed.

Form work to sides and soffits of floor roof beams, beams haunching, girders, bressummers, lintels, cantilevers, shelves including supports, over hangers etc also splays between floor and beam etc all as specified for rough finished surface of concrete flat complete all as specified and as directed.

Form work to edges of concrete flats, treads, window cills, floor and roofs not exceeding 20 CM for rough finished surface for concrete flat complete all as specified and as directed.

Form work to sides of pillars, posts, struts, piers columns and stanchions for rough finished surface of concrete flat complete all as specified and as directed.

Reinforced cement concrete Design Mix M-25 as in foundation including rafts, footing, plinth beams, bases for columns etc. complete all as specified and as directed.

Reinforced cement concrete Design Mix M-25 as in columns, pillar, pier, posts etc complete all as specified and as directed.

Reinforced cement concrete Design Mix M-25 as in beams, cantilevers, lintels etc complete all as specified and as directed.

Reinforced cement concrete Design Mix M-25 as in slab etc complete all as specified and as directed.

Rendering 15 mm thick in two layer (10 mm + 5 mm) on fair faces of brick/concrete surfaces in cement mortar 1:4 and finished even and fair without using extra cement complete including WPC @ 2% by weight of cement complete all as specified and as directed (WPC shall be measured separtely).

10 mm thick rendering on fair faces of brick surfaces finished even and fair as on concrete surface in CM 1:3 as in ceiling complete all as specified and as directed.

40 mm thick PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregates) as in flooring finishing with extra cement complete all as specified and as directed.

Providing 50 mm thick cement concrete 1:3:6 type C-2 (using 40 mm graded crushed stone aggregates) as in plinth protection laid in alternate bays (not exceeding 2 Sqm each) and finished even and smooth without using extra cement complete all as specified and as directed.

Punched tape concertina coil (including spike and handle) with 50 turns and 1050 mm dia, width of barbed 9 mm dia and spacing of clips 23.5 mm to 24.5 mm c/c, weight of coil will be 10 to 14 kg without packing. Coil length will be 6 Mtrs when opened up etc. complete all as specified and as directed.

Wall cladding colour tiles of size 300 mm x 600 mm x 7 mm thick (As approved by GE) set in neat cement slurry laid over & including screed bed/backing layer of rendering 10 mm thick in cement mortar 1:4 and pointed in white/coloured cement to match the colour of tiles as on vertical surfaces such as dado/ skirtings complete all as specified and as directed.

Taking down carefully aluminium/copper point wiring complete with (light, fan, socket or power) complete fitting such as switch, sockets, ceiling rose, pendents sockets any type, rectangular board terminal boxes etc and making good disturbed surface of walls, and all as specified keeping aside serviceable item for re-use within the same bldg and removing unserviceable item from site complete all as specified and as directed.

Point wiring for one light point/fan point/Bell ponit controlled by one switch with 1.5 Sqmm PVC insulated FRLS unsheathed copper conductor single core multi stranded flexible copper cable in and including not less than 1.50 mm thick 20 mm dia & over concealed PVC non metallic rigid PVC conduit (ISI marked) with 1.5 mm thick pressed steel terminal boxes (modular type) concealed for fixing of modular switches/regulator etc. along with PVC insulated and insheathed FRLS 1.5 Sqmm multi stranded copper conductor cable (green color) as earth lead in and inculding PVC Concealed Conduit medium grade with all fitting (ISI make), as directed by Engr-in- Charge & including modular cover plate with frame, making good the disturbed surfaces to match with the existing specification complete all as specified and as directed. Make - Havells or equivalent make in polycab/finolex.

All as per ser item No 129 but for 05 amp socket outlets point controlled by one switch on Independent board complete all as specified and as directed.

All as per ser item No 129 but for 05 amp socket outlets point controlled by one switch on same board complete all as specified and as directed.

All as per ser item No 129 but for 3 pin 20 A socket outlet point controlled by one modular switch 20A on the independent board with 2.5 Sqmm size of copper cable as main and 2.5 Sqmm copper cable as earth lead complete all as specified and as directed.

Switch button single pole one way 5 amps 240 volt (Modular Type) with outer strip complete all as specified and as directed. Note - All modular cover plate/modular flush Box/Switch/Sockets Incorporated with this, should be in same.

Switch piano fiush button single pole one way 20 amps 240 volt (Modular Type) with outer strip complete all as specified and as directed.

Sockets Combined 2-in-1, 3 pin 6 Amps, 240 Volt flush type (Modular Type) with outer strip, complete all as specified and as directed.

Sockets Combined 2-in-1, 3 pin 20 Amps, 240 Volt flush type (Modular Type) with outer strip, complete all as specified and as directed.

Bell AC Ding dong, 230 Volts, single pole with all acessories complete all as specified and as directed.

Bell Push, 6 amp, 230 Volts, 1 module (Modular type) complete all as specified and as directed.

Ceiling rose surface bakelite, 3 terminals complete all as specified and as directed.

Replacement fan regulator 120W, 230V 50 C/S, deluxe Modular type electronic, step type hum free suitable control speed of fan from 0 to 100 % and connecting electrically all as required complete all as specified and as directed.

Taking down carefully existing ceilling/exaust fan any type sweep and removing fan blade including cleaning all dust particle and filling cavities with filler material, oiling and assemble the same along with all fixing connecting accessories and fixing the same position along with all new electrical wire connection complete all as specified and as directed.

Aesthetically designed, 2x2 LED flat panel 34 watt for surface (including electronic driver) for surface mounting which provides soft-light and glare free symmetrical illumination suitable for (600 x 600 x 70 mm) surface mounting complete making all connection using 1.5 Sqmm copper conductor multistarnd PVC insulated 3 core flexible cable complete all as specified and as directed. Make - Havells/Wipro/Syska

Slim linear LED tube light fixture 20 Watt, with T8 polycarbonate 6500k Housing made of extruded AL with lumen O/P should not be less than 100 lum/watt making all connection using 1.5 Sqmm copper conductor multistranded PVC insulated 3 core flexible cable from ceiling rose to fitting drawn through PVC flexible conduit complete all as specified and as directed. Make - Havells/Wipro/Syska

Slim linear LED lighting fixture 5 Watt LED Batten, For mirror light purpose , Complete making all connection using 1.5 Sqmm copper conductor multistarnd PVC insulated 3 core flexible cable from ceiling rose to fitting complete all as specified and as directed. Make - Havells/Wipro/Syska

Surface decorative 12 Watt LED Peocock , 6000K, wall/ceiling mounted fixture with electronic driver and opaque diffuser, suitable for indoor applications complete all as specified and as directed. Make - Havells/Wipro/Syska

10 watt ZOOM downlights (round) WW recessed mounted round COB based fully adjustable LED spot light complete all as specified and as directed. Make - Havells/Wipro/Syska

Slim linear decorative, wall mounting, SS finish fixture with opal glass diffuser suitable for LED lamp (Including LED lamp warm white) complete all as specified and as directed. Make - Havells/Wipro/Syska

10 watt LED hexagon bulk head, IP66, Environmental friendly, ultra modern, energy saving, surface mounted, complete making all connection using 1.5 Sqmm copper conductor multistarnd PVC insulated 3 core flexible cable complete all as specified and as directed. Make - Havells/Wipro/Syska

Earthing complete with galvanised cast iron earth plate electrode of size 600 x 600 x 6 thick as earth electrode with top edge of earth plate not less than 1.5 m below ground level using GI wire 4 mm dia as earth continuity conductor connected to earth plate by means of GI thimbles nuts bolts washers all as directed inculding providing earth wite protection pipe GI light grade 15 mm dia from earth plate to main switch board/panal, watering pipe 20 mm dia with mesh and funnel at top, earth pit and RCC pit cover in PCC 1:3:6 adequate quantity of characoal dust and salt all around the earth plate, earth work in any type of soilo remaning surplus excavated material all as required at site and complete all as specified and as directed in EP No 3 of SSR Part I 1991.

Replacement of Sheet metal enclouser single pole and neutral with 2 pin and earth plug and socket 20A 240V complete with one single pole MCB of any cap from 10 Amp to 20 Amp, 10KA complete all as specified and as directed.

Sheet metal enclosure MCB distribution board single pole & neutral 240 volts 12 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification including taking down old one complete all as specified and as directed. Make - Indoasian/Legrand/ Standard. Note - MCBs will be measured separately.

Replacement MCB single pole 240 volt any rating from 10 to 32 amps, B-Series, with rupturing capacity 10 KA, inculding providing aluminium thimble for out going cable complete all as specified and as directed. Make - Legrand/Havells/Schneider

Replacement MCB Single Pole & Neutral 240 volt any rating from 40 to 63 amps, B-series, with rupturing capacity 10 KA, inculding providing aluminium thimble for out going cable complete all as specified and as directed. Make - Legrand/Havells/Schneider

Supply & Laying in trenches or passing through pipe, 1100 volts grade heavy duty cable with XLPE insulated aluminium conductor standard served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed of Sqmm 25 x 3.5 core size complete all as specified and as directed including taking down old cable. Note : Earth work and other connected work shall be measured & paid seperately.

Brick covering width equal to length of brick for mechanical protection to cable with well burnt sub class 'B' bricks laid dry flat complete all as specified and as directed.

Sand cushioning for under ground cable provided with a layers of 8 mm high before laying cable and 15 mm thick after laying and stretching the cable complete all as specified and as directed.

Galvanized steel pipe light grade with all fitting laid in trenches or passing through cable/road crossing or fixing along pole with suitable size clamps complete of size 40 mm dia complete all as specified and as directed.

VTPN MCCB DB-Double Door (Including 63 Amp MCCB) 16 kA (as Incommer) 4 way double door IP-43 protection complete all as specified and as directed. (Including All PCC & Cementing work for installation of TPN DB to Wall, deemed to be quoted rate by contractor)

Point wiring for one light point/fan point/bell point controlled by one switch with 1.5 Sqmm PVC insulated FRLS unsheathed copper conductor single core multi stranded flexible copper cable in and including not less than 2.00 mm thick 20 mm dia over PVC Non metallic Rigid PVC Conduit (ISI marked) with 1.25 mm thick pressed steel terminal MS boxes recessed on walls, painted the same inside and out side with one coat of black bitumen paint incl inner and laminated sheet for, piano switches/sockets/regulator etc along with PVC insulated and insheathed FRLS 1.5 Sqmm multi stranded copper conductor cable (green color) as earth lead, to match with the existing specification complete all as specified and as directed.

All as per ser item No 159 but for 15 amp socket outlets point controlled by one switch on Independent board with cable 2.5 Sqmm complete all as specified and as directed.

All as per ser item No 159 but for 15 amp socket outlets point controlled by one switch on Independent board with cables 4 Sqmm complete all as specified and as directed.

Switch piano type 5 Amps 230 volts one way complete all as specified and as directed. Make - Anchor/Havells/Kinjal

Switch - socket combination 15 Amps, 6 pin multipurpose complete all as specified and as directed. Make - Anchor/Havells/Kinjal

100 watt LED Flood light, Energy saving, environmental friendly, long life, exclusive innovative die-cast aluminium IP66 flood light, suitable for highlighting architectural facade, complete all connection using suitable cable, fixed with suitable clamps as required on ground and complete all as specified and as directed. Make - Havells (JETA AIRIS) JETAIRISFLS 100WLED757APNBLT G

Replacement MCB TPN 240 volt any rating 63 amp with rupturing capacity 10 KA, inculding providing aluminium thimble for out going cable complete all as specified and as directed. Make - Legrand/Havells/Schneider

Sheet metal enclosure MCB distribution board single pole & neutral 240 volts 8 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification including taking down old one complete all as specified and as directed. Note - MCBs will be measured separately.

LED street Light fitting 60 Watt, New generation energy saving & environmental friendly long life versatile pressure die-cast aluminium IP66 with acrylic, with Heat resistant toughened Glass, Corrosion resistant, complete making all connection with MCB SPN alongwith MCB Box enclosure complete all as specified and as directed. Make - Havells/Wipro/Syska

Street light Bracket complete made of GI pipe of suitable size of 40 mm, medium grade 1.2 m long bent to shape as per site requirement along with MS flat iron clamps with nuts, bolts, washers including grouting the same with wall complete all as specified and as directed.

Supply & Laying in trenches or passing through pipe, 1100 volts grade heavy duty cable with XLPE insulated aluminium conductor standard served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed of Sqmm 6 x 3 core size complete all as specified and directed including taking down old cable complete all as specified and as directed. Note : Earth work and other connected work shall be measured & paid seperately.

Dry sand for sand cushioning to under ground cable 8 cms thick before laying the cable before and 15 cms thick after laying & streching the cable in trenches, including hand punning and consolidating complete all as specified and as directed. Note : for payment purpose punned thickness shall be measured

GI tubing light grade 40 mm dia along the wall/ in trenches/in duct/in culvert/road crossing and including provisioning of suitable mild steel flat iron clamps and bolts, nuts and double washers etc for holdining of GI pipe alongwith poles complete all as specified and as directed.

SINGH CONST CO

RAJ MOHD

R K BUILDERS