REPAIR/MAINT TO LT PANEL APFC ALLIED WORKS AT INSTALLATION AT GMS UNDER GE I GOS

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off premises complete all as specified and directed

M&L for non skid ceramic coloured tiles of design as approved 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed in cement mortor 1:6 complete all as specified and directed.

M&L for non skid ceramic coloured tiles of design as approved 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed in cement mortor 1:6 complete all as specified and directed.

M&L for glazed ceramic coloured tiles 350 x 250 x 7 mm / 450 x 350 x 7 mm thick on vertical surface such as dado / skirting / risers to steps etc jointed in neat cement slurry and pointed in white or coloured cement to match surface of tiles over and including rendering 10 mm thick in cement mortor 1:4 complete all as specified and directed. Note- (i) The size of tiles (except thickness) may be varied during execution without any price adjustment.

M&L 16 to 18 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

Demolition of cement concrete un reinforced in ground floor and paving n exc 15cm thick (below or above ground level) complete all as specified and directed.

M&L for PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in sub base flooring average 25 mm thick surface finished even and rough (as in levelling course) to receive the topping layer complete all as specified and directed.

S&F pre- painted galvalume aluminum zinc corrugated steel based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping serews complete all as specified and directed.

Dismantling asbestos cement (corrugated, semi corrugated etc) sheets in roof coverings including ridges complete all as specified and directed.

M&L for Fe 410-W (Gde E-250 quality A) Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and directed.

M&L for Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed.

Demolition of brickwork built in cement or cement lime mortar including all quoins, arches pillar etc complete all as specified and directed.

M&L Brick work with flyash bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

Taking down cement or cement lime plaster, of any description, on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for Rendering 15 mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces, finished even and smooth (without using extra cement) complete all as specified and directed.

M&L for rendering 5 mm thick in CM 1:3 on RCC ceiling surface and finished even and smooth with out using extra cement complete all as specified and directed .

M&L for applying 2mm thick Birla / JK Putty in two layers on newly plastered walls surfaces making absolutely even and smooth, rubbing with sand paper complete all as specified and directed

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs /blankets, any thickness, including cover fillets complete all as specified and directed.

S&F 12 mm thick plain Gypsum Board False Ceiling with GI frame including all necessary drilling cutting to fix electric items complete all as specified and directed with following:- (a) GI Grid channel 30x25x20 mm of 24 gauge fixed with rawl plug and screw 450 mm centre to centre alongwith perimeter walls. (b) GI channel made to shape 50x40x40 mm of 24 gauge placed @ 600 mm centre to centre from perimeter at wall except long wall (in one span). (c) GI intermediate runners of size 45x10x10 mm of 24 gauge fixed @ 1200 mm centre to centre leaving frame of one side walls (in other span). (d) GI sheet 25 mm wide and 20 mm gauge suspended fixed with steel fastner to roof ceiling and 1200 mm centre to centre including pluging of RCC Slab. (e) 12 mm thick gypsum board filling joints with POP and finishing complete with two coat of plastic emulsion paint over one coat of primer on ceiling.

M&L for applying two coats of oil bound distemper on wall or concrete surfaces over & including a coat of primer on prepared surfaces including, rubbing with sand paper complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and apply three coat of white wash complete all as specified and directed.

M&L for preparation of newly plastered surfaces of ceilings and apply three coat of white wash complete all as specified and directed.

Taking down chowkhat or frames n exc 1.50 Sqm each with shutters (without taking off shutters from the frame) and removing to store complete all as specified and directed

Taking down chowkhat or frames exc 1.50 Sqm and n exc 4 Sqm each with shutters (without taking off shutters from the frame) and removing to store complete all as specified and directed

S & F Powder coated three track Aluminium sliding window with frame not less than 1.8 mm thick excluding aluminium grill and including 4 mm thick tinted glass, beading & necessary rubber packing, locking & opening arrangement, all fitting and fixture complete all as specified and directed.

S&F 7mm thick aluminium grills of make "Decogrill' model DG 104 surrounded by aluminium 'C' channel with mesh size 75 X 75mm complete all as specified and directed.

S&F aluminium alloy wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminium wire staples complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet re-inforced with MS square tube in opening complete all as specified and directed shown on drg SSR Part-II 2020.

S&F, factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain cover PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheet for top rails lock rail and bottom rail on either side & as gap insert for top rail and bottom rail paneling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and jointed together with solvent cement , complete all as specified and directed shown on drawing in SSR Part-II (2020).

Taking down shutter of any description area exceeding 1 sqm but n exc 2 sqm each and removing to store complete all as specified and directed.

S&F Flush shutters 35 mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of wood and wood based surfaces of any description, over 10 cm in width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Taking down shutter of any description not exceeding 1 sqm each leaf and refixing, in same opening after easing and adjusting building hard ware etc complete all as specified and directed

Taking down shutter of any description exceeding 1 sqm but not exiding 2 Sqmeach leaf and refixing, in same opening after easing and adjusting building hard ware etc complete all as specified and directed

M&L Second class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S&F mild steel flat iron as in bands straps, supports or stays for rainwater, ventilating pipes including bolt if required, hooks (stay) heavy for large gates,hook and pintle hinges,large hasps and staples, brackets for WHB, hold fasts, wall ties, hooks for hanging fans ,cleats for securing purlins to wood trusses or rafters and similar small articles conforming to Fe -290 Gde E-165 complete all as specified and directed.

M&L for Cutting holes in brick walls exc half brick but not exc one brick built in cement mortor or cement lime mortor and stone walls built in lime mortor for inserting hold fasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required complete all as specified and directed.

S&F 150 mm long aluminium anodised, barrel tower bolts of extruded section and fixed etc complete all as specified and directed.

S&F 100 mm long aluminium handles cast type, anodized complete all as specified and directed

S&F 250 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed

S&F 100 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed

S&F in repair 100 mm long aluminium anodized handles fabricated type complete all as specified and directed

S&F in repair 150 mm long aluminium anodised, barrel tower bolts of extruded section and fixed etc complete all as specified and directed.

S&F in repair 100 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed

S&F in repair 75 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed

S&F in repair 250 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed

S&F in repairs 300 mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

Hacking out old broken glass (any thickness, size quality or description) form wooden frames or stone, concrete or brick surrounds glazed with oil putty or fixed with beads complete all as specified and directed.

S&F 3 mm thick sheet glass ordinary quality and gazing with oil putty in square n exc 0.5 sqm in each pane complete all as specified and directed.

S&F 3 mm thick figured glass pin headed type and gazing with oil putty in square n exc 0.5 sqm in each pane complete all as specified and directed.

S&F in repairs aluminium alloy wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminium wire staples complete all as specified and directed.

S&F in repairs 18/19 mm thick high density PVC/ WPC solid fibre board with prelaminated PVC sheet as Kitchen cupboard and frame including taking down the old cupboard shutters and removing to store complete all as specified and directed.

S&F continuous (piano) hinges of width of flaps (when open) 30 mm, mild steel, bright finish or electrogalvanised complete all as specified and directed

S & F magnetic catcher catcher with nut and screw of mild steel bright finish complete all as specified and directed.

S & F 40 mm dia cupboard knobs fixed with nuts screw and washer of mild steel bright finish complete all as specified and directed.

S & F in repair 40 mm dia cupboard knobs fixed with nuts screw and washer of mild steel bright finish complete all as specified and directed.

S & F in repair hasp and stapple safety type aluminium anodised 75 mm long with mild steel hinge pin including bolt to hinge plate fixed with screw complete all as specified and directed.

S&F in repairs 15 mm dia Curtain rods, mild steel, chromium plated with fixing brackets complete all as specified and directed.

S&F in repair floor door stopper of aluminium alloy body and tongue, anodised, over all length of cover plate 140 mm with hard drawn steel spring fixed in door etc complete all as specified and directed.

S&F in repair single door PVC cabinet mirror of size 300 mm x 450 mm with internal shelves complete all as specified and directed.

S & F in repair sheet Glass Shelf assembly consisting of 5.5 mm glass sheet shelf 12 cm wide with cromium plated bracket guard and railing 60 cm long complete all as specified and directed..

Taking up or down steel tubing and connections including cleaning if refixing required for 15 mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing and connections including cleaning if refixing required for 20 mm bore of pipe complete all as specified and directed.

S&F GI tubes medium grade (ISI marked) with all fittings fixed complete to walls, ceilings or laid in floors of 15 mm bore of pipe complete all as specified and directed.

S&F GI tubes medium grade (ISI marked) with all fittings fixed complete to walls, ceilings or laid in floors of 20 mm bore of pipe complete all as specified and directed.

S & F 15 mm bore 3 layer PP-R pipes SDR 7.4 & SDR 11 UV stablised and anti microbial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded PP-R fittings complete to walls, ceilings or in floors complete all as specified and directed.

S & F 20 mm bore 3 layer PP-R pipes SDR 7.4 & SDR 11 UV stablised and anti microbial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded PP-R fittings complete to walls, ceilings or in floors complete all as specified and directed.

Making connection of PPR distribution branch with PPR main of following outer dia of pipe 16 to 40mm size by providing and fixing tee including cutting and making fusion joint etc complete all as specified and directed.

Refixing old steel tubing and connections in new or old position (wall, floor, ceiling etc) of 15 mm bore of pipe complete all as specified and directed.

Refixing old steel tubing and connections in new or old position (wall, floor, ceiling etc) of 20 mm bore of pipe complete all as specified and directed.

S&F in repairs bib taps cast copper alloy with crutch or butterfly handle fancy type, screwed down, screwed for iron pipe or for brass ferrule of 15 mm bore dia of pipe complete all as specified and directed.

Taking down bib tap /wash basin tap/pillar tap/stop cock/mixture tap and refixing the same after repair and replacement of washer only for 15 mm bore size without replacing spindles complete all as specified and directed.

Taking down bib tap /wash basin tap/pillar tap/stop cock/mixture tap and refixing the same after repair and replacement of spindles for 15 mm bore size complete all as specified and directed.

S & F in repair Brass chromium plated wall mixer non-telephonic shower arrangement with connecting legs & wall flanges for 15 mm bore of pipe complete all as specified and directed.

S & F in repair Brass chromium plated hole bidet mixer (Basin mixer) with pop-up waste system with 300 mm long braided hoses complete all as specified and directed.

S & F in repair Brass chromium plated Sink mixer with raised J shaped swinging spout (Wall mounted model) with connecting legs & Wall flanges complete all as specified and directed.

S&F in repair Chromoium plated angle cock, cast copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe or brass ferrule, 15 mm bore complete all as specified and directed.

S&F in repair Chromoium plated Two-way angular stop cock for 15 mm bore complete all as specified and directed. Make-Jaquar CON-059KN or equivalent of higher cost.

S&F in repair, 15 mm bore stop cock, cast copper alloy with long shank and cup (concealed type) fancy type chromium plated screwed down high pressure with crutch & butterfly handle screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in repair 15 mm bore stop cock, cast copper alloy screwed down high pressure with crutch & butterfly handle fancy type chromium plated screwed both ends for iron pipe and fixed complete all as specified and directed

S&F in repair pillar tap cast copper alloy with capstan head chromium plated screwed down high pressure with or without lettered hot or cold with long screwed shanks and ply nuts 15 mm bore complete all as specified and directed

S & F in repair bottle trap chromium plated for WHB as per approved quality complete all as specified and directed.

S&F in repair PVC waste pipe for WHB etc complete all as specified and directed.

S&F in repairs 32 mm bore waste coupling of (min weight 32 mm-45 gm of PTMT) (half or full threaded) etc complete all as specified and directed

S&F in repair CP grating 100 mm dia with waste hole (minimum weight 40 gm) complete all as specified and directed

S & F in repair CP Jet spray for 15 mm bore complete all as specified and directed.

S & F in repairs Hand shower (Health faucet) with 1 mtr long Easy flex tube in crome finish & wall hook complete all as specified and directed.

S&F in repairs for vitreous china wash basin, white,flat back, size 550 x 400 mm including supply & fixing of brass chromium plated coupling 32 mm etc complete all as specified and directed.

S&F in repair Wash down water closet vitreous china white pedestal pattern with 'P' or 'S' trap including connecting to outgoing drain pipe & to flushing pipe excluding flushing cistern and flush pipe complete all as specified and directed.

S&F in repairs plastic water closet seat cover, closed pattern with recessed bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S&F in repairs vitreous china squatting pan , ‘Orissa’ Pattern, size 580 X 440 mm white, with integral foot rests etc. complete all as specified and directed.

S & F in repair Kitchen sink made of stainless steel 1 mm thick with plug washer and waste pipe incl bedding fixing cantilever brackets and connetction union to pipe overall size 915 X 460mm bowl size 405X 355 mm complete all as specified and directed

S& F in repair 1 mm thick stainless steel plate rack of size 900X600X200 incl fixing with rawal plug and screws complete all as specified and directed.

S & F rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) 500 litre capacity hoisted and fixed in position including dismantling of old u/s water tank and removing to store complete all as specified and directed

S & F rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) 1000 litre capacity hoisted and fixed in position including dismantling of old u/s water tank and removing to store complete all as specified and directed

S&F ball valves for 20 mm bore of pipe high pressure of PTMT with Epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight 210 gms) complete all as specified and directed.

S&F ball valves for 25 mm bore of pipe high pressure of PTMT with Epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight 455 gms) complete all as specified and directed.

S&F in repairs ball valves for 20 mm bore of pipe high pressure of PTMT with Epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight 210 gms) complete all as specified and directed.

S&F in repairs ball valves for 25 mm bore of pipe high pressure of PTMT with Epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight 455 gms) complete all as specified and directed.

S & F in repair PVC Tank cover for 500 Ltr capacity fixed in position with nuts and bolt complete all as specified and directed

S & F in repair PVC Tank cover for 1000 Ltr capacity fixed in position with nuts and bolt complete all as specified and directed

S&F in repairs, PVC valveless syphonic action type low level flushing cistern, 10 ltrs capacity with inlet, ball valve, float and handle including bracket complete all as specified and directed

S & F in repair internal fitting for low level flushing cistern (Syphon) complete all as specified and directed.

S&F in repairs flush pipe 32 mm dia of polyethylene of low or high density or PVC, for low level cistern complete all as specified and directed.

S & F in repair 125 mm dia chromium plated shower rose of with or without swivel joint incl fixing to steel pipe complete all as specified and directed.

S&F in repair PVC connection 15 mm bore, 450 mm long complete with both ends unions complete all as specified and directed.

S&F in repairs CP anodised tubular tower rail, 20 mm dia, D type, 60 cm long between flanges etc complete all as specified and directed.

S & F in repair 75 mm PVC(SWR) floor trap with grating incl jointing with solvent cement complete all as specified and directed

S&F in repair Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe of 20 mm bore of pipe complete all as specified and directed.

S&F in repair Gun metal globe or gate valves with iron wheel head screwed both ends (ISI marked) for iron pipe of 25 mm bore of pipe complete all as specified and directed.

S & F in repair Soap dish any type fixed to plug with chromoium plated brass screw complete all as specified and directed.

S & F in repair corner glass shelf with brackets complete all as specified and directed.

S&F in repairs door seal with aluminium beading and 50 mm wide rubber seal complete fixed to aluminium/ Wooden doors complete all as specified and directed.

Taking down carefully old UNSV aluminium point wiring with wooden batten /concealed and all accessories of(light, fan, socket or power) such as switches socket ceiling rose, fan regulators, light fitting, main switches DB’s etc and making good disturbed surface complete all as specified and directed.

M&L in repairs for point wiring with cable PVC insulated sheathed, 1.5 Sqmm, stranded copper conductor FRLS in and including PVC conduit duly concealed continuous earthing with cable PVC insulated 1.5 Sq mm copper conductor cable FRLS for earth continuity wire and modular MS box including modular top cover,washer & screw complete all as specified and directed for One light/Call bell point controlled by one, one way switch.

All as per item No 117 above but for one exhaust fan point controlled by one, one way switch.

All as per item No 117 above but for 5 Amp socket point controlled by one switch on independent board.

All as per item No 117 above but for one 5 Amp socket point controlled by one switch on same board.

M&L in repairs for point wiring with cable PVC insulated sheathed, 1.5 Sqmm, stranded copper conductor FRLS and including PVC casing caping duly fixed on walls continuous earthing with cable PVC insulated 1.5 Sq mm copper conductor cable FRLS for earth continuity wire , modular MS box including modular top cover,washer & screw complete all as specified and directed for One light point controlled by one, one way switch.

All as per item No 121 above but for one fan point controlled by one switch.

All as per item No 121 above but for one 3 pin 5 Amps socket outlet point on independent board

All as per item No 121 above but for one 3 pin 5 Amps socket point on the same board

S&F in repairs modular socket 6A , 2/3 pin combined 2 module complete all as specified and directed. Make :- ABB / Crabtree / Cona or equivalent of higher cost.

S&F in repairs modular switch 6A complete all as specified and directed. Make :- ABB / Crabtree / Cona or equivalent of higher cost.

S&F in repairs modular switch 1 way 16A, 1 module complete all as specified and directed. Make :- ABB / Crabtree / Cona or equivalent of higher cost.

S&F in repairs modular socket 6A / 16A , 2/3 pin combined 2 module complete all as specified and directed. Make :- ABB / Crabtree / Cona or equivalent of higher cost.

S & F in repairs for modular step type fan regulator 120 watt 2 module suitable for 230 volt 50 Hz AC supply complete all as specified and as directed.

S&F in repairs modular Ceiling rose 3 termianl complete all as specified and directed. Make :- ABB / Crabtree / Cona or equivalent of higher cost.

S&F in repair LED light fitting 18/ 20 Watt T5 batten type,PVC extruded batten with decorative end caps complete with polycarbonate /glass tube 4Ft White , internally pre-wired and including connecting up with suitable twisted flexible copper conductor cable with suitable size complete all as specified and directed. Note: Contractor shall submit warranty for 3 years.

S & F in repair of light fittings (2Ft) with wall mounted LED pattern with polycarbonate housing & integrated electronic driver of 9W cap T5(max lenght upto 600mm) complete all as specified and directed. Make :- (Make C&S /WIPRO/ CG / Phillips / Havells) (Note : Contractor shall submit warratny for 03 yrs)

S & F in repair recess mounting LED Endura slim pro plus ceiling light suitable for armstrong/grid ceiling complete capacity 36W, sIze 2'x2' complete all as specified and as directed including taking down the old rusted tube light fitting.complete all as specified and directed. Note: Contractor shall submit warranty for 3 years.

M&L in repairs for replacement of 2 Runs of cable PVC insulated sheathed, 4.0 Sq mm, stranded copper conductor FRLS in and including PVC conduit with continuous earthing cable PVC insulated 2.5 Sq mm, stranded copper conductor Note: Contractor shall submit warranty for 3 years. complete all as specified and directed (Cable make Anchor/ Havells /Finolex) or equivalent of higher cost.

S&F in replacement sheet metal enclosure double door MCB DB, SPN 12 way complete all as specified and directed

S&F in replacement MCB SPN 16 TO 32 Amp 10 KA 240 Volts (Make : Anchor/ Standard/ C&S/Havells/HPL) or equivalent of higher cost.

S&F in replacement MCB, SP 6 to 30 Amp 240 Volts rating (Make : Anchor/ Standard/ C&S/Havells/HPL) or equivalent of higher cost.

S&F exhaust fan, steel body AC single Phase. 230V of size 380m sweep with, blades, and frame and louvers complete all as specified and directed

S&F in repairs octane+ led panel round recess mounted round fixture with opal diffuser and electronic driver with capacity 3 W complete all as specified and directed. Make : Havells cat part No LHEBADSP6IZ1W003 or equivalent of higher cost.

S&F in repairs octane+ led panel round recess mounted round fixture with opal diffuser and electronic driver with capacity 6 W complete all as specified and directed. Make : Havells cat part No LHEBADP7IZ1W006 or equivalent of higher cost.

S&F in repairs recess mounting luminaaire with high performance LEDs suitable for mounting with armstrong/ grid ceiling of capacity 18W complete all as specified and directed. Make : Havells cat part No LHEBHEP7IZ1W018 OR EQUIVALENT of higher cost.

S&F in repairs foot lights 3W, 240 Volts, 50 Hz complete all as specified and directed

S&F in repairs LED bollard light fitting with capacity 8W, 240 volts, 50 HZ complete all as specified and directed. Make: Havells cat part No CONEBLS8WLED857PSYMTOPC OR equivalent of higher cost.

S&F in repairs alluminium service cable 10 Sqmm 2 Core complete all as specified and directed

S&F in repairs fabricated Y junction GI medium grade 40 mm bore pipe pole 3 mtr long complete all as specified and directed

Supply, Installation & commissioning in replacement of APFC panel 100 KVAR outdoor floor mounting type busbar capacity 25x8 alumimum Bus bar 3 and 1/2 bar DMC Insulator with busbar supporter body 3.15mm CR sheet colour totally powder coated with square type capacitor following in 05/06/08 steps including PCC work complete all as specified and directed make of panel CPRI Approved make of switch gear : L&T ,ABB, Siemens, HAVELLS Incoming (i) 200 Amps MCCB 3 Pole 25 KA - 1 No. Outgoing (i) 5 KVAR box type - 2 No (ii) 10 KVAR box type - 2 No (iii) 15 KVAR box type - 2 No (iv) 20 KVAR box type - 2 No

Supply, Installation & commissioning in replacement of APFC panel 75 KVAR outdoor floor mounting type busbar capacity 25x8 alumimum Bus bar 3 and 1/2 bar DMC Insulator with busbar supporter body 3.15mm CR sheet colour totally powder coated with square type capacitor following in 05/06/08 steps including PCC work complete all as specified and directed. make of panel CPRI Approved make of switch gear : L&T ,ABB, Siemens, HAVELLS Incoming (i) 160 Amps MCCB 3 Pole 25 KA - 1 No. Outgoing (i) 5 KVAR box type - 1 No (ii) 10 KVAR box type - 2 No (iii) 15 KVAR box type - 2 No (iv) 20 KVAR box type - 1 No

M&L in repairs earthing complete with galvanised steel earth plate electrode 60cm x 60cm x6mm thick burried directly in ground (earth pit not less than 2.25 m deep below normal ground level, connecting to the Galvanised iron earth lead 32x6mm size, by means of bolts, nuts, check nuts and washers of galvanised iron and 32x6 mm earth lead protected by provision of GI medium grade pipe 40 mm bore including provision of concrete pit in PCC 1:2:4 type B-1 using 20 mm graded crushed stone aggregates with 40 mm thick cover of RCC (1:2:4) reinforced with XPM (weight not less than 4kg/Sqm) and frame of angle iron 25x25x3 mm with lugs-02 Nos and with 6 mm dia MS bar handle made to shape, GI medium grade 20 mm bore pipe for watering perforated at bottom 1.5 meter long placed on top edge of earth plate common salt and charcoal filling, test point with fixing arrangements, funnel wire mesh and earth work in hard/dence soil returning filling in and removal of surplus soil to a distance not exceeding 50 m, all as per electrical plate No 5 of SSR-2009 Part-I and connecting to earth test point complete all as specified and directed.

(b) 70 KVAR to 125 KVAR

M&L for replacement of power capacitor box type of the following capacities (a) 3 KVAR box type heavy duty capacitor 440V Make:- L&T / HAVELLS/ ABB / SIEMENS

(b) 5 KVAR box type heavy duty capacitor 440V Make:- L&T / HAVELLS/ ABB / SIEMENS

(c) 10 KVAR box type heavy duty capacitor 440V Make:- L&T / HAVELLS/ ABB / SIEMENS

(d ) 15 KVAR box type heavy duty capacitor 440V Make:- L&T / HAVELLS/ ABB / SIEMENS

(e ) 20 KVAR box type heavy duty capacitor 440V Make:- L&T / HAVELLS/ ABB / SIEMENS

(f ) 25 KVAR box type heavy duty capacitor 440V Make:- L&T / HAVELLS/ ABB / SIEMENS

S&F in repairs Contactors capacitor duty rating 3 phase 415 V suitable for 3 KVAR Make:- L&T / HAVELLS/ ABB / SIEMENS

S&F in repairs Contactors capacitor duty rating 3 phase 415 V suitable for 5 KVAR Make:- L&T / HAVELLS/ ABB / SIEMENS

S&F in repairs Contactors capacitor duty rating 3 phase 415 V suitable for 10 KVAR Make:- L&T / HAVELLS/ ABB / SIEMENS

S&F in repairs Contactors capacitor duty rating 3 phase 415 V suitable for 15 KVAR Make:- L&T / HAVELLS/ ABB / SIEMENS

S&F in repairs Contactors capacitor duty rating 3 phase 415 V suitable for 20 KVAR Make:- L&T / HAVELLS/ ABB / SIEMENS

S&F in repairs Contactors capacitor duty rating 3 phase 415 V suitable for 25 KVAR Make:- L&T / HAVELLS/ ABB / SIEMENS

S&F in repairs timer 5 A 0 - 60 seconds 230 V Make:- L&T / HAVELLS/ ABB / SIEMENS

S&F in repairs display/relay unit computerised control of Power Factor Digital type 4 steps 440 V Make:- L&T / HAVELLS/ ABB / SIEMENS

S&F in repairs display/relay unit computerised control of Power Factor Digital type 8 steps 440 V Make:- L&T / HAVELLS/ ABB / SIEMENS

S&F in repairs display/relay unit computerised control of Power Factor Digital type 12 steps 440 V Make:- L&T / HAVELLS/ ABB / SIEMENS

S&F in repairs LED Indicator 20mm dia replaced by old indicator Make:- L&T / HAVELLS/ ABB / SIEMENS

S&F in repairs LED Indicator 15mm dia replaced by old indicator Make:- L&T / HAVELLS/ ABB / SIEMENS

Taking down old U/S MCB and Supply & Fix MCB four pole 63A .10 KA 415 V Make:- L&T / HAVELLS/ ABB / SIEMENS

Taking down old U/S switch and Supply &Fix switch fuse unit TPN 500 Volts 3 phase with HRC fuses suitable for interior mounting in panel of capacity of 63 Amps each Make:- L&T / HAVELLS/ ABB / SIEMENS

Taking down old U/S MCCB and Supply & Fix MCCB 3/4 POLE 100 A 16 KA 415 V Make:- L&T / HAVELLS/ ABB / SIEMENS

All as per item no 171 above but 200 Amps 4 pole 36KA, 415 V Make:- L&T / HAVELLS/ ABB / SIEMENS

S&F in replacement of XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 95 Sqmm 3.5 core complete all as specified and directed

Supply testing and commissioning in replacement AC single phase,50Hz, digital,electronic tamper proof energy meter of rating 5 to 30 Amps covered with PVC transparent cover with optical communication port incl taking down the unsv meter complete all as specified & Directed

S&F in repairs octane+ led panel round recess mounted round fixture with opal diffuser and electronic driver with capacity 12 W complete all as specified and directed. Make : Havells cat part No LHEBADP5IZ1W012 or equivalent of higher cost.

S&F in replacement of wall fan 400 mm sweep with full copper motor with high air thrust, overload thermal performance with 2200 RPM, 240 volts 50 Hz complete all as specified and directed. Make Bajaj/ Havells/C&S

M/S. KISHAN ENGINEERING

M/s MAA BHAIRABI ENTERPRISES

M/s Bapujee Builders and Traders