DNIT for Supply, Installati...

Amount

L3 Core Switch-Network switch Supply and Installation: High End Switch should have 24 10/100/1000 Base-T Ports including 4 x1000Base loaded with 2 10SFP+ module single mode and 2x 1G SFP 1G SFP module, combo with 4 10G SFP+ ports separate for Stacking and upling purpose, Switch should have Console Port (RJ-45 and Mini-USB console ports) for out-of-band CLI management, provide a direct, physical connection to the switch for management tasks, which can be especially useful if remote management is not possible, Switch should have separate 10/100/1000BASE-T RJ-45 Ethernet port for out-of-band IP management, even if the main data ports are saturated or malfunctioning. Switch should have 1 x RJ-45 port Alarm Port for various purposes, such as signaling system alerts or connecting to monitoring devices. Should have USB 2.0 Port Type A for connecting storage devices for file sharing or providing power to external devices. 64K MAC Address and 4MB Packet buffer memory. 128 Gbps Switching capacity and 95 Mpps packet forwording rate. Power Support and Energy Efficiency: The Switch should support Power Input 100 to 240 VAC 50/60 Hz with Maximum Power Consumption should be not more than 42 W , while Standby Power Consumption should not be more than 28 W. Switch should support Redundant Power Supply (RPS) support from day1. The Switch Operating Temperature should be -5 to 50 °C (23 to 122 °F) with Storage Temperature • -40 to 70 °C (-40 to 158 °F). Surge Protection upto 6 kV surge protection on all Ethernet access ports. Energy-Efficient Ethernet (EEE) standard and save power with shutoff LED and port shut-off and power on link while there is no activity and draw power only as per cable length used. IPv6 Support and Stacking Capabilities: Switch should be able to do Physical stacking upto 9 switches in a stack with total 80 Gbps stacking bandwidth in Ring/chain topology. Switch should be able to do Virtual stacking/clustering of up to 32 units with Single IP Management upto 20 Gbps stacking bandwidth. The Switch should be IPv6 Ready Certification for IPv6 Ready Logo Phase-2. Layer 2 Features: Switch should support 802.3x Flow Control with HOL blocking, Switch should support 802.1D, 802.1w , 802.1s. It also support Root Guard and Loop Guard. Switch should support jumbo Frame: up to 12 Kbytes. Support 802.1AX Link Aggregation, Max. 32 groups per device, 8 ports per group. Support ERPS (Ethernet Ring Protection Switching) version 2. Support Port Mirroring ( One-to-One, Many-to-One) , also Supports Mirroring for Tx/Rx/Both, upto 4 mirroring groups, Flow Mirroring, Supports Mirroring for Rx, VLAN Mirroring. Support Remote Switched Port Analyzer, to takes a mirrored copy of network traffic from within the switch to be sent to a destination. Switch should support L2 Protocol Tunneling to support one Layer 2 (L2) protocol within another L2 protocol for the purpose of transporting it across a network. Support Multi-Chassis Link Aggregation Group (MLAG). Layer 3 Features: Switch should support 256 IP interfaces , support Static Route,support VRRP v2/v3. Switch should support RIPing, OSPF v1/v2, BGP v4. Switch should support VRF-Lite, IS-IS v4/v6, BGP/MPLS VPN, MBGP, Virtual Private Wire Service (VPWS), Virtual Private LAN Service (VPLS). QoS (Quality of Service): Switch should support Queue Handling Strict Priority (SP), Weighted Round Robin (WRR) and Strict + WRR , Weighted Deficit Round Robin (WDRR). Should have Congestion Control protocol i.e. Weighted Random Early Detection (WRED) 802.1Qbb Priority-based Flow Control (PFC) for 10 GbE port. Bandwidth Control based on flow or Port min. 8kb. Support QoS based on Time , CoS , Switch port, Inner/outer 802.1p Priority , Inner/outer VLAN ID, MAC address, Ether Type, IP address, ToS/IP Preference, DSCP, Protocol type, TCP/UDP port, IPv6 Traffic Class, • IPv6 Flow Label. Security Features: Switch should support 12K MAC addresses per port/VLAN for connected devices, thus preventing unauthorized access and mitigating security risks. Switch should support Broadcast/Multicast/Unicast Storm Control for effectively manage and mitigate the impact of excessive traffic on their network infrastructure, ensuring optimal performance and reliability by using any specifc protocl. Switch should support DHCP Server Screening to prevent rogue DHCP servers from distributing incorrect or malicious IP configuration information to network. Dynamic ARP Inspection to avoid traffic interception, packet sniffing, or denial of service attacks. IP-MAC-Port binding in assiociation with IP Source Guard, DHCP snooping and Dynamic ARP Inspection (DAI). support Duplicate Address Detection (DAD), ARP Spoofing Prevention. Should support Unicast Reverse Path Forwarding (URPF) and Traffic Segmentation. Switch should support SSL, TLS 1.0/1.1/1.2, SSH. OAM and AAA services: Switch should support Cable Diagnostics, 802.3ah Ethernet Link OAM, unidirectional Link Detection, Dying Gasp, 802.1ag Connectivity Fault Management (CFM), Y.1731 OAM, Optical Transceiver Digital Diagnostic Monitoring (DDM). Supports port/host-based access control, MAC-based Access Control (MAC) Support MAC based Identity-driven Policy Assignment. Should be SDN-enabled compatible with Openflow 1.3, allowing the switches to be managed using an OpenFlow controller.Switch shuold be compatable with existing Network switches for HA mode. Make- Cisco/D-Link/Juniper complete in all respects with the prior approval of Engineering in charge.

24 Port Managed Switch -Network Supply and Installation: Switch should have 24x 10/100/1000BASE-T ports Ports with 4 10G SFP+ ports for uplink purpose. Switch should have Console Port (RJ-45) for out-of-band CLI management, provide a direct, physical connection to the switch for management tasks, which can be especially useful if remote management is not possible, Should have 16K MAC Address and 12MB Packet buffer memory. Switch should have 128 Gbps Switching capacity and 95 Mpps packet forwording rate. Power Support and Energy Efficiency: The Switch should support Power Input 100 to 240 VAC 50/60 Hz with Maximum Power Consumption should be not more than 30 W , while Standby Power Consumption should not be more than 9 W. Operating Temperature should be -5 to 50 °C (32 to 122 °F) with Storage Temperature • -20 to 70 °C (-40 to 158 °F), Support Surge Protection upto 6 kV surge protection on all Ethernet access ports. Support Energy-Efficient Ethernet (EEE) standard and save power with shutoff LED and port shut-off and power on link while there is no activity and draw power only as per cable length used , Also the complete switch can be hibernet during off period i.e. Night to save power. Layer 2 feature: support 802.3x Flow Control with HOL blocking, Switch should support 802.1D, 802.1w , 802.1s. It also support Root Guard and Loop Guard Switch should support jumbo Frame: up to 12 Kbytes. Support 802.1AX Link Aggregation, Max. 8 groups per device, 8 ports per group. Port Mirroring (One-to-One, Many-to-One) , also Supports Mirroring for Tx/Rx/Both, Should support Remote Switched Port Analyzer, to takes a mirrored copy of network traffic from within the switch to be sent to a destination. Layer 3 feature: Switch should support 4 IP interfaces , support Static Route,124 IPv4 static route entries • 50 IPv6 static route entries. Should support Queue Handling Strict Priority (SP), Weighted Round Robin (WRR) and Strict + WRR , Bandwidth Control with min granularity 10/100/1000 is 16 Kbps). Switch should support QoS based on Time , CoS , Switch port, Inner/outer 802.1p Priority , MAC address, Ether Type, IP address, ToS/IP Preference, DSCP, Protocol type, TCP/UDP port, IPv6 Traffic Class, support 64MAC addresses per port for connected devices, thus preventing unauthorized access and mitigating security risks. Broadcast/Multicast/Unicast Storm Control for effectively manage and mitigate the impact of excessive traffic on their network infrastructure, ensuring optimal performance and reliability by using any specifc protocol.Support DHCP Server Screening to prevent rogue DHCP servers from distributing incorrect or malicious IP configuration information to network. Dynamic ARP Inspection to avoid traffic interception, packet sniffing, or denial of service attacks. Switch should support IP-MAC-Port binding in assiociation with IP Source Guard, DHCP snooping and Dynamic ARP Inspection (DAI). Support SSL, TLS 1.0/1.1/1.2, SSH. Switch should support Cable Diagnostics, Switch should carry Safety Protocl i.e. cUL, CB, CE, CCC, BSMI and EMI/EMC i.e. CE, FCC Class A, C-Tick, VCCI, BSMI, CCC. . Make- Cisco/D-Link/Juniper complete in all respects with the prior approval of Engineering in charge.

SFP Module Network Switch 1 G Short Distance Supply and Installation: Supply & Installation of 1G SFP Module. Make- Cisco/D-Link/Aruba complete in all respects with the prior approval of Engineering in charge.

8 Port Managed Switch ( 8+2 ) Managed GIG Switch Supply and Installation: Switch should have 8x 10/100/1000BASE-T Ports with 2 x 1G SFP ports for uplink purpose. Switch should have 8K MAC Address and 4.1MB Packet buffer memory. 20Gbps Switching capacity and 14 Mpps packet forwording rate. Power Support and Energy Efficiency: The Switch should support Power Input 100 to 240 VAC 50/60 Hz with Maximum Power Consumption should be not more than 7W , while Standby Power Consumption should not be more than 3W. The Switch Operating Temperature should be -5 to 50 °C (32 to 122 °F) with Storage Temperature • -20 to 70 °C (-40 to 158 °F). Layer 2 Features: Switch should support 802.3x Flow Control, HOL Blocking Prevention ,Switch should support 802.1D, 802.1w , 802.1s. It also support Loopback Detection, Switch should support jumbo Frame: up to 10 Kbytes. Support 802.1AD Link Aggregation, Max. 4 groups per device, 8 ports per group. Support Port Mirroring ( One-to-One, Many-to-One) , also Supports Mirroring for Tx/Rx/Both. Remote Switched Port Analyzer, to takes a mirrored copy of network traffic from within the switch to be sent to a destination. Switch Should support IGMP v1/v2 snooping, v3 awareness, IGMP authentication/filtering upto 256 groups, VLAN/host-based IGMP snooping fast leave Report suppression MLD Snooping v1, v2 awareness. Support 802.1Q VLAN , 256 static VLAN groups, Configurable VID from 1 - 4094, Asymmetric VLAN, automatically applying the correct VLAN and QoS settings when an IP phone is connected, Max. 10 user-defined OUI, Max. 8 default OUI, to uniquely identify devices on a network. Should support automatically detects and prioritizes surveillance video traffic on a network. Layer 3 Features: Switch should support 4 IP interface , support IPv6 Neighbor Discovery (ND), Static routing upto 124 IPv4 / 50 IPv6 static route entries. QoS (Quality of Service): Switch should support Queue Handling Strict Priority (SP), Weighted Round Robin (WRR) , Bandwidth Control with min granularity 10/100/1000 is 64 Kbps). QoS based on Time , CoS , Switch port, Inner/outer 802.1p Priority , MAC address, Ether Type, IP address, ToS/IP Preference, DSCP, Protocol type, TCP/UDP port, IPv6 Traffic Class. Security Features: Support 64MAC addresses per port for connected devices, thus preventing unauthorized access and mitigating security risks. Support Broadcast/Multicast/Unicast Storm Control for effectively manage and mitigate the impact of excessive traffic on their network infrastructure, ensuring optimal performance and reliability by using any specifc protocol. Support DHCP Server Screening to prevent rogue DHCP servers from distributing incorrect or malicious IP configuration information to network. Support ARP Inspection to avoid traffic interception, packet sniffing, or denial of service attacks.AMC/IP based ACL with Source/destination IP address mask. Switch should support IP-MAC-Port binding in assiociation , DHCP snooping and ARP Inspection. Switch should support SSH v2 and TLS v.1.2.OAM and AAA services:. Make- Cisco/D-Link/Aruba complete in all respects with the prior approval of Engineering in charge.

6U Rack with PDU & Accessories for Netwok Swiches Supply and Installation: Wall Mount 6U /9 U x 550 W x 500 D, 1U Cable Manager, Roof Mounted Fan Unit / 90 CFM / 230V AC,6 Way 5 Amp Power Distribution Unit,Mounting Hardware Kit,Conforms to DIN 41494 OR equivalent ISO Standards, Adjustable 19” equipment mounting verticals provide the better mounting flexibility, and maximizes the usable mounting space,Depth adjustable mounting slots,Front Glass Door with Lock, Top and bottom Panel with ventilation and cable entry facility, Provision to mount the cooling fans on the top panel, Powder coated finish with Seven Tank pretreatment process meeting all industry standards, Grounding and Bonding Options. 100% assured compatibility with all equipments conforming to DIN 41494 (General industria lstandard for equipments) Make- D-Link/Schneider/Dynamic complete in all respects with the prior approval of Engineering in charge.

9U Rack with PDU & Accessories Supply and Installation: Wall Mount 9U x 550 W x 500 D, 1U Cable Manager, Roof Mounted Fan Unit / 90 CFM / 230V AC,6 Way 5 Amp Power Distribution Unit,Mounting Hardware Kit,Conforms to DIN 41494 OR equivalent ISO Standards, Adjustable 19” equipment mounting verticals provide the better mounting flexibility, and maximizes the usable mounting space,Depth adjustable mounting slots,Front Glass Door with Lock, Top and bottom Panel with ventilation and cable entry facility, Provision to mount the cooling fans on the top panel, Powder coated finish with Seven Tank pretreatment process meeting all industry standards, Grounding and Bonding Options. 100% assured compatibility with all equipments conforming to DIN 41494 (General industria lstandard for equipments) B Make- D-Link/Schneider/Dynamic complete in all respects with the prior approval of Engineering in charge.

27 U Rack with PDU & Accessories Supply and Installation: 27 U Rack The rack should have 1U Cable Manager, The rack should have minimum 2 Nos of Roof Mounted Fan Unit / 90 CFM / 230V AC, It should have 6 Way 5/15 Amp Power Distribution Unit, Casters Set of 4 (2Nos with Brake and 2Nos without Brake). The rack should have adjustable Levellers set of 4, Front Glass Door-24U-600mm Rear Door Vented-24U-600mm, Vented Side Panels-24U-800mm (set of 2) with Slam Latch. Conforms to DIN 41494 OR equivalent ISO Standards, Ral 9005(Black) Powder Coated, Equipment Mounting on DIN Standard 10mm Sq. Slots / Direct M6 Tap, Mounting Angle should be 19” Mounting angle made of formed steel, Vented and Cable entry/exit cut outs from Top & Bottom. Static Load should be 250 kgs or better. Depth adjustable mounting. Provision to mount the cooling fans on the top panel. Make- D-Link/Schneider/Dynamic complete in all respects with the prior approval of Engineering in charge.

6 Core Armoured Fiber Optics Cable Supply and Installation: Fiber is optimized for operation at 1310 nm and at 1550 nm. The Fiber should be Armoured 6 core unitube 9/125 µm SM fiber with central loose tube jelly compound, Glass Yarns in between Steel Tape & Loose Tube. Armour Tape : Corrugated steel Tape Armoured Jacket material : HDPE, Outer diameter : 9 ± 0.3 mm Thickness of the Jacket: 1.8 + 0.2 mm Pulling Tension: Short Term 2000N, Long term 1000N, Crush Load: 3000N/100mm, The Fiber Operating Temperature should be – 20 deg C to +60 deg C and The Fiber Max Attenuation ± 0.36 (db / km) @ Operational Wavelength 1310 nm and, ± 0.22 (db/ km) @ Operational Wavelength 1550 nm. Fiber - type should be 9/125 / G.652D & Refractive Index should be 1.4670/1.4675. Value for Mode-filed/Cladding Diameter (um) 9.2 ± 0.4 and 125 ± 0.7. Dispersion value <=3.5 <=18 (ps/(nm-km) and PMD value <=0.2 (ps/km) and Cable Cut-off wavelength <=1260 (nm). The Fiber should follow Standards: ISO 11801, IEC 60793-1/60794-1-2 and ITU-T-REC G.652D. Testing methods are in accordance with the following standards: ITU-T G.652.D, IEC 793-1 and Telecordia : GR-20 Core.- Make: D-Link/Commscope/Belden complete in all respects with the prior approval of Engineering in charge.

AP Supply and Installation: 4X4 Access Point Physical Interfaces : One 100/1000/2.5GBASE-T Gigabit Ethernet (RJ-45) ports with Auto Uplink (Auto MDI-X) supporting IEEE 802.3af or 802.3at Power over Ethernet (PoE),Two (2) Internal 3.1/4.3 dBi (2.4GHz/5GHz) antenna ,Four (4) LED: Power and Cloud connection; LAN speed; 2.4GHz status; 5.0GHz status,Power adapter (not included): 12V DC, 2.5A. Standards : 5.0GHz: 802.11a/n/ac/ax; 2.4GHz: 802.11b/g/n/ax , IEEE 802.11ax WiFi 6 standard , WMM - Wireless MultiMedia Prioritization , WDS- Wireless Distribution System , Power over Ethernet (PoE) IEEE 802.3af/802.3at. Security : Wi-Fi Protected Access (WPA, WPA2, WPA3), 802.11i, WPA2 Enterprise , Wireless access control to identify authorized wireless network devices , MAC address filtering with access control , 802.1x RADIUS support with EAP TLS, TTLS, PEAP, Neighbor AP detection, VLAN Support, Secure Socket Layer (SSL), Guest Network/Captive Portal, Bandwidth management, Link Layer Discovery Protocol. Network Management : Cloud based App Management for setup, monitoring and management from anywhere anytime (Remote configuration and management), Easy-to-use Web browser-based management GUI, Manageability : As standalone, Centralized Management through Mobile Application. Advanced Wireless Features : Wireless Distribution System (WDS), Bridge mode: Point-to-point wireless WDS mode, Bridge mode: Point-to-multipoint wireless WDS mode, Repeater mode, Adjustable Transmit Power Control (TPC), Device detection, Identify type of wireless clients in the network. Other Specifications : PoE power consumption: 25.5W, Business class WiFi based on next generation 802.11ax WiFi 6 technology on both 5.0GHz and 2.4GHz bands. Backward compatible to 802.11b/g/n/a/ac, Dual band 4x4 (2.4GHz and 5.0GHz) 8 streams of data for an aggregate throughput of up to 3.6Gbps, Theoretical Throughput per Band: 5.0GHz: 2400Mbps; 2.4GHz: 1200Mbps, Orthogonal Frequency Division Multiple Access (OFDMA), Multi-Gigabit Support, Target Wake Time (TWT), Basic Service Set Coloring (BSS Coloring), Bandsteering, Block SSID Broadcast, Ceiling mounting / Wall mounting, Bidir and MU-MIMO support. Warranty and Support : , 3 Years Centralized Management license included, 5 Years free latest firmware support, Rs. Make- Cisco/Netgear/Ruckus complete in all respects with the prior approval of Engineering in charge.

8 Port Gigabit PoE+ Managed Switch for AP Network with 2 SFP Port Supply and Installation: Supports up to 8 10/100/1000Mbps Gigabit Ethernet PoE ports and 4 SFP slots, IEEE 802.3af/at PoE compliant to simplify deployment and Supports PoE up to 30W per port with 140W total power budget. 8 10/100/1000 Base-T Ethernet PoE Ports 4 Gigabit Combo (RJ-45/SFP) Ports Reset Button: reset to default setting, Switching Capability: 24Gbps MAC Address Table: 8K PoE Power Budget: 140W Packet buffer size: 4.1MB Jumbo Frame: 10K. L2 Features Auto-negotiation for port speed and duplex mode Spanning Tree Protocol-Support STP / RSTP / MSTP (max 16 instance)-Loopback Detection- BPDU Filter- BPDU Guard, LLDP IGMP v2/v3 Snooping: IGMP Querier, Immediate Leave MVR VLANs - 256 IEEE 802.1q tag based VLAN with 4K VLAN ID - MAC Based VLAN, Voice VLAN, Guest VLAN, Management VLAN Link Aggregation- LACP: 8 Groups, 8 Ports/Group-Static Trunk. Queueing Mechanism: SP and WRR Classifications based on- COS, COS DSCP, IP Precendence, Each port supports 8 queues Rate Limit (Port Based): Ingress/ Egress Port Flow Control. MAC address Binding Support Broadcast/Multicast/Unicast storm control IP and MAC ACL (Ipv4) RADIUS, 802.1x based Authentication Port Security, Protected Port Management ACL DHCP Snooping, DHCP Snooping option 82, IP Source Guard, IP-MAC-Port-VLAN Binding. Management Port Mirroring Support traffic statistics, FAN less design, Provide IPv4 Web-based management IPv4 DHCP Client Configuration Backup and Recovery Dual firmware images and Configuration files Error Disabled, Bandwidth Utilization, SNMP v1/v2c/v3 C11 Remote Server Telnet, SSH,HTTP, HHTPS RMON, SNTP Ping, Traceroute EEE, Port Statistics. 330(W) x 230(D) x 44(H) mm, AC Power: 100 to 240 V, 50-60 Hz, Input Surge Protector. IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX, IEEE 802.3ab 1000BASE-T, IEEE 802.3az IEEE, IEEE 802.3at & IEEE 802.3af. Temperature : Operating: 0°C ~ 40°C Storage: -40°C ~ 70°C Humidity: perating: 10% ~ 90% RH (Non-condensing) Storage: 5% ~ 90% RH (Non-condensing) Display Each port have a dedicated LED status display. Link/Act Hardware Factory Reset button. Traffic on a port can be mirrored to another port for analysis with a network analyzer. . Make- Cisco/Digisol/Juniper complete in all respects with the prior approval of Engineering in charge.

Supply and Installation: Category Patch Panel should be 24 Port 1U Size loaded with 24 port RJ-45 IO/Jack,Mounts in standard 19 inch racks,Patch panel should have rear cable manager for improvement management,Patch panel suitable for Category 6 keystone,Panel material should have SPCC with 1.5mm thickness and Black Color,Support bar material should have SPCC with 1.5mm thickness and Black Color,RJ-45 jack housing should be PBT + Glass fiber UL94V-O and Contact brackets should be PBT + Glass fiber UL94V-O,Rj-45 contact material should be phosphor bronze with nickel plated and plug contact area finish with 50 micro-inches Gold plated, Rj-45 jack life should be 700 times minimum,Operating temperature should be -10° Celsius to 60° Celsius.Make- D-Link/Molex/Commscope complete in all respects with the prior approval of Engineering in charge.

Patch cord Supply and Installation: Category 6 patch cords 1 /2 Mtr with four pair twisted cable terminated with RJ45 modular plugs at both the ends,Patch Cord should have TIA/EIA 568C.2 standard.,Shall be backward compatible with Category 5 and Category 5e systems, Category 6 patch cord should be 100% factory made and performance tested,Category 6 patch cord length requires – 2 meter/ 1 meter,Color code for Patch Cord: Grey,Performance Characteristics ,Patch cord conductor should be 24 AWG, multi-strands ,Patch core conductor metal should be made from bare copper,Insulation material should be high density polyethylene,Patch cord jacket should be LSZH,Modular Connector/Plug Characteristics,Patch cord plug should be gold plated,Contact blade of plug should be made from copper / alloy,Insertion cycle should be 750 times,Temperature range should support from 10° Celsius to 60° Celsius.. Make- D-Link/Digisol/Commscope complete in all respects with the prior approval of Engineering in charge.

Fibre Patch Cord Supply and Installation: Adopts high precision ceramic ferrule with good concentricity, Fiber corning single mode G652D,G657A,G657B, Cable Type 0.9mm, Optical Fiber – Corning multi Mode, Connector: Zirconia ceramic ferrule, Pre-radiuses and pre-polished ferrule, Mechanical specification Apex Offset :-< 50 um, Mechanical specification Fiber Height +(-) 100 nm, End-face radius of Curvature 7mm < R <25mm, Repeatability <(-) 0.2 db, Working Temperature :- -4 0 c ~ +85 o C Storage Temperature:- 40 o C ~ + 85 o C, Type -- LC-LC MM Duplex. Make- Digisol/Commscope/Belden complete in all respects with the prior approval of Engineering in charge.

12 Core LIU loaded with Singlemode Adaptors and Pigtail Supply and Installation: Aluminum base material for light mounting. Should be Rack Mountable for 12 Port and should be loaded with LC Type Adaptors. Front-mounted cable saddles for jumper management. Can manage both splices and terminations. Preassembled shelves in multiple configurations, Rubber fiber slotted bracket built-in, metal splice shelf to protect the fibers, Snap-in locker design, easy to change adapter panels for various connector patching, Capable of storing up to 1 meters of 900μm tight buffered fiber per adapter, Space saving with its compact & small design of enclosure. Removable front and rear covers for better access to interior of LIU, Removable rubber grommet allows for pre-terminated fiber trunk instillation, protects cable, Should be Singlemode LC Type pigtail fully loaded. . Make- Digisol/Commscope/Belden complete in all respects with the prior approval of Engineering in charge.

Information Outlet setup with Gang Box and Face Plat Supply and Installation: Category 6 keystone jacks are RJ45, 8 position 8 contact socket. Category 6 keystone jacks are suitable for 22-26 AWG stranded and solid wire. Keystone jacks are compatible with both 110 & Krone punch down tools. The Category 6 keystone jacks shall be backward compatible with Category 5e, 5 and 3 cords and cables. It compliance with ANSI/TIA/EIA 568 C.2 standard. The Category 6 keystone jacks shall be of a universal design supporting T568 A & B wiring. Color of Keystone Jack: White Category 6 keystone jacks housing made from PC, UL 94V-2 material. RJ45 Jack contact material should be phosphor bronze with nickel plated. Finished with 50 micro-inch gold plated on plug contact area. IDC Housing made from PC, UL 94V-2. Terminal material should be Phosphor bronze with tin plated. Should have IDC CAP and material of IDC Cap should be PC, UL 94V-2. Current rating should be 1.5A. Life of Jack should be 750 cycles minimum (ISO/IEC 11801/IEC 60603-7-4). Operating Temperature should be -10° Celsius to 60° Celsius. Make- D-Link/Commscope/Belden .Supply and Installation: Face plate should be single port with Back box. Face Plate should have shutter to protect from dust. It should have write on labels in transparent plastic window – supplied with plate. Face plate material: ABS with white color. Screw should be supplied with face plate Make- D-Link/Commscope/ Molex complete in all respects with the prior approval of Engineering in charge.

5 MP Fix Lens IP Dome/Bullet Camera Supply and Installation: Project series 5MP IP Dome/Bullet Camera with inbuilt mic Image Sensor: 1/2.7” 5MP Progressive scan Lens: 3.6mm fixed lens Resolution: 2592(H)×1944(V) or Higher IR Distance: 30 Mtr. Angle of View: Horizontal: 79°, Vertical: 56°, Diagonal: 106°,Min illumination 0.003lux @ F1.6(AGC ON),Video Compression: H.265+; H.265; H.264+; H.264; H.264B; MJPEG ,Video Streaming: Mainstream @30fps5MP(2592x1944),4MP(2592x1520),3MP(2304x1296),1080P(1920x1080), 960P(1280*960) ,Substeam @30fps 1080P(1920x1080)720P(1280x720),VGA(640x480), Third stream @30fps VGA(640x480), QVGA（320x240; Motion Detection: 8 Level, Rectangle ; Major Protocols should include most of the following TCP/IP,HTTP,DHCP,DNS,DDNS,RTP/RTSP, SMTP,NTP,UPnP,SNMP,HTTPS,FTP, ONVIF (Profile S/Profile G/Profile T); Smart Detection: Face Recognition,Human&Vehicle Detection,Perimeter Intrusion Detection,Line Crossing Detection, Cross Counting,Stationary Object Detection,Heat Map,Crowd Density Detection,Queue Length Detection, Rare Sound Detection, WDR(120dB),Micro SD Card Slot up to 256GB, Privacy Mask, ICR auto switch Power Source: 12V DC/PoE Casing: Metal ,Weatherproof Standard: IP67, Certification: BIS,CE,FCC,ROHS. The product should be ONVIF certified . C Make- Honeywell Project Series/Bosch Project series/Axix Project series complete in all respects with the prior approval of Engineering in charge.

64 Ch 16 Sata NVR with Software Supply and Installation: Network Video Recorder with Software to view 64 Channel, support 64 Channel, Should support Resolution:- greater than equal to 12 MP IP Camera, Network Bandwidth incoming 1024 Mbps and outgoing 800 Mbps for access, support for H.265+/H.265/H.264 encoding format streaming access and decoding output, Recording play back quality: 16 ch play back simultaneously, Recording resolution up to 12MP, Recording mode: support manual, Auto, Motion detection, Alarm, trigger record mode, Operation way: Mouse, local Login: Username and password, Recording storage: Local HDD, network, Video output:Support 4 HDMI,RS232 & RS485, Support min. 16 SATA HDDs , Each port supports min. 18TB HDD(Enterprise class),support-RAID0, RAID1, RAID5, RAID6, RAID10,Support dual Gigabit Ethernet ports,Supports 2 HDMI outputs with a maximum of 4K HD output,Alarm Input/out:16 in /4 out ,Audio:1 in / 1 out ,support Hot swappable, Supports intelligent analytics such as Licence plate detection,Face Recognition,Human&Vehicle Detection,Perimeter Intrusion Detection,Line Crossing Detection, Cross Counting,Stationary Object Detection,Heat Map,Crowd Density Detection,Queue Length Detection, Rare Sound Detection. The product should be ONVIF certified. Make- Honeywell Project Series/Bosch Project series/Axix Project series complete in all respects with the prior approval of Engineering in charge.

2 MP 25 X PTZ Camera Supply and Installation: 2MP 25X PTZ camera Image Sensor 1/2.8" Progressive Scan CMOS ;Max. Resolution 1920x1080 ;Min. Illumination Slow Shutter Color: 0.002 Lux @ (F1.6, AGC ON), B/W: 0 Lux with IR;IR cut ??lter; Shutter Speed 1/5 s to 1/20000s Day & Night Zoom 25x optical; LENS Focal Length 5.0 mm to 125 mm FOV Horizontal ??eld of view: 56.9° to 2.9° (wide-tele), Vertical ??eld of view: 32.2° to 1.6° (wide-tele), Diagonal ??eld of view:65.2° to 3.3° (wide-tele); Aperture Max. F1.5; Focus Auto, Manual Resolution Up to 1920x1080 @30fps Optical Zoom: 25x ;Video Compressions H.265+/H.265/H.264 ;Alarm & Audio:1 Inputs,1 Output; IP66 FEATURES AND BENEFITS Metal Slot Up to 256GB; DORI (5.0mm) D-69.0m,O-27.6m, R-13.8m, I-6.9m(125mm) D-1724.1m,O-689.7m, R-344.8m, I-172.4m; IR Distance: up to 150 m; Movement Range(Pan) 360° Movement Range(Tilt) -10° to 90° (auto ??ip); Pan Speed Pan speed: con??gurable from 0.6° to 200°/s; preset speed: 200°/s; Tilt Speed Tilt speed: con??gurable from 0.6° to 90°/s, preset speed 100°/s; Presets 255; Patrol Scan 1 Scan; Pattern Scan 4 pattern; Power-Off Memory Yes; 3D Positioning Yes ; Video Compression Main stream: H.265+/H.265/H.264+/H.264; SubstreamH.265+/H.265/H.264+/H.264/MJPEG; Third stream: H.265+/H.265/H.264+/H.264; Audio Compression G.711a/G.711u; Protocols TCP/IP, ICMP, HTTP, HTTPS, FTP, DHCP, DNS, DDNS, RTSP, NTP, UPnP, SMTP, IGMP, 802.1X, IPv4, IPv6, UDP, SSL/TLS, PPPoE, SNMP, SFTP API Onvif ( Pro??le S, Pro??le G, Pro??le T) Simultaneous Live View Up to 15 channels User/Host 5 User Security Password protection, complicated password, HTTPS encryption, IP address ??lter,control timeout settings Web Browser IE10/11, Safari V12.1 above, Firefox V.52 above, Google chrome V.57 above, Edge V.79 above; Day/Night Switch Day, Night, Auto, Schedule Image Enhancement BLC, HLC, 3D DNR Wide Dynamic Range (WDR) True WDR Image Settings Saturation, brightness, contrast, sharpness, Hue and white balance adjustable by client software or web browser Privacy 4 Privacy masks; Basic Event Motion detection, alarm input and output Deep Learning Function Face Recognition, Human & Vehicle Detection, Perimeter Intrusion Detection, Line Crossing Detection, Stationary Object Detection, Crossing Counting, Heat Map, Crowd Density Detection, Queue Length Detection Smart Tracking Auto-tracking Alarm Linkage Upload to FTP, send email, trigger alarm output, trigger recording; Power DC 12V/POE+, max. 22 W Operating Condition -30 °C to 60 °C (-22 °F to 149 °F). Humidity 90% or less (non-condensing) Material Metal; Protection IP66 .The product should be ONVIF certified . Make- Honeywell Project Series/Bosch Project series/Axix Project series complete in all respects with the prior approval of Engineering in charge.

Hard Disk Survilliance Supply and Installation: Surveillance HDD 8TB with 5640rpm Make: WD/SEAGATE/Toshiba complete in all respects with the prior approval of Engineering in charge.

24 Port Managed Switch for Camera Power Supply and connectivity Supply and Installation: Switch have 19" Rack Mountable (1U) Dimension- 440 x 200 x 44 mm, Architecture- Non Blocking, It provides 24 10/100/1000Base-TX ports with PoE + 2 gigabit Combo ports(RJ45/SFP) + 2 gigabit SFP ports, Support 2 gigabit combo ports (RJ45/SFP) + 2 x gigabit SFP Ports, Management interface-Web/SNMP/SSH/Telnet(IPv6 support)/Console, 270W (PoE+ supported) with (6Kv) surge protection. Port status-Power, Link/Act, PoE, PoE-Support IEEE802.3af, IEEE802.3at, 24 port PoE Interfaces, Max. PoE Wattage per Port: 30W, With 6 Kv surge protection per port, Supported Up to 8K MAC addresses, Switching Capacity 56GbpS forwarding rate 41.7 MBPS. Supports upto 4K VLAN Based on 802.1Q,MAC-Based VLAN, IP-Based VLAN. Protocol-Based VLAN, Voice VLAN, Guest VLAN, Private VLAN, VLAN Mapping, Double VLAN Markup (Basic Q-in-Q), Support Static MAC Address, MAC Binding, MAC Filtering, Support Web Management, Support serial port management, Support TELNET management, Support SSH management, Support RMON 1,2,3,9 group, support port loop detection, Support STP/RSTP/MSTP, Support manual Link Aggregation, Support LACP, Up to 8 maximum aggregation groups, each containing up to 8 ports. QoS Support-WRR, SP,WFQ, Sorting Based on 802.1p, Support packet mapped to the corresponding output queue, Support to modify the packet’s COS and DSCP sign, Support limit of data flow, Support statistics of data flow, Support mirroring of data flow, Based on Standard IP, Extend IP, MAC IP, MAC ARP, On Time, Port Filtering. Support DHCP Snooping, Support IGMP Snooping. IPv6- ICMPv6, IPv6 Neighbor Discovery, MLD Snooping, IPv6 Telnet. Each port can be configured into isolated protected port from each other. Support SNMP protocol, Support SNMP TRAP, Support standard and private MIB. Support neighbor discovery protocol, Support topology discovery protocol, Support manual and automated join cluster group, Support cluster unification management. OAM-Support 802.3ah, Support 802.1ag, Debugging Tolls- Support Ping, Traceroute, Telnet client. Support many to one mirroring, Support dynamic ARP binding to prevent ARP spoofing, Support dynamic IP,MAC port binding, Support stationary port connect to DHCP server, to prevent privately connect to DHCP sever, Support 802.1x protocol, RADIUS , Support MAC-based 802.1X authentication, Support 802.1x guest VLAN, switch supports EAPS, ERPS Ring protocols, Make: Digisol/Cisco/Juniper complete in all respects with the prior approval of Engineering in charge.

8 Port Managed Switch for Camera Power Supply and connectivity Supply and Installation: Wall/Desktop Mountable-Architecture- Non Blocking, 8 Port 10/100/1000 with PoE Web Managed Switch + 2 Fiber SFP ports, It should suppport 2 No's 1000 Base mini GBIC/SFP tans receivers LC connector for connecting single mode fiber(LX), 75W (PoE+ supported), Display Each port must have a dedicated LED status display. Supported Up to 8K MAC addresses. Switching Capactity At least 20 Gbps, Forwarding rate Packet throughput 14 Mbps or more, Support for up to 4096 VLANs simultaneously Port-based and 802.1Q tag-based VLANs MAC-based VLAN, Traceroute; single IP management; HTTP; SSH; RADIUS; port mirroring; TFTP upgrade; DHCP client; BOOTP; SNTP; cable diagnostics; ping; syslog; Telnet client (SSH secure support), RMON, Management-Web Management, L2 Loop Protection- IEEE 802.1d Spanning tree protocol, IEEE 802.1W RSTP(Rapid spanning Tree Protocol), IEEE 802.1s Multiple Spanning Tree Protocol (MSTP). Link aggression-Support for IEEE 802.3ad Link Aggregation Control Protocol (LACP) Up to 8 groups-Up to 8 ports per group with 16 candidate ports for each (dynamic) 802.3ad link aggregation. Qos-Atleast 4 nos of 802.1p Priority Queues per Port.Traffic on a port can be mirrored to another port for analysis with a network analyzer or RMON probe. Up to 8 source ports can be mirrored to one destination port. A single session is supported. TFTP or FTP Support - For Configuration file backup and restore. The ability to lock Source MAC addresses to ports, and limits the number of learned MAC addresses. Access control-Should support standard and extended ACLS. Should support various types of ACLS like port based/time based.AC Input 100-240V AC. 54VDC/1.67 A. Should be TEC certified and ROHS compliant. Make- Digisol/Cisco/Juniper complete in all respects with the prior approval of Engineering in charge.

17 U Rack with PDU ,Accessories for Camera NVR Supply and Installation: Wall Mount 17 U x 600 W x 600 D, 1U Cable Manager, Roof Mounted Fan Unit / 90 CFM / 230V AC,6 Way 5 Amp Power Distribution Unit,Mounting Hardware Kit,Conforms to DIN 41494 OR equivalent ISO Standards, Adjustable 19” equipment mounting verticals provide the better mounting flexibility, and maximizes the usable mounting space,Depth adjustable mounting slots,Front Glass Door with Lock, Top and bottom Panel with ventilation and cable entry facility, Provision to mount the cooling fans on the top panel, Powder coated finish with Seven Tank pretreatment process meeting all industry standards, Grounding and Bonding Options. 100% assured compatibility with all equipments conforming to DIN 41494 (General industria lstandard for equipments). Make- Dlink/Dynamic/Hikvision complete in all respects with the prior approval of Engineering in charge.

Display Supply and Installation: 55 inch, Professional Display, 350 nits or higher, Response Time- 8 ms or lower, 4K UHD (3840 * 2160), Backlight type-Direct LED, Viewing Angle (Right/Left/Up/Down) 178 Degree, Android, HDR Compatibility-HDR10, HLG,16 GB On-board Storage or more, Wi-Fi Certified & Wireless LAN, Chromecast & Apple AirPlay built in, IP Control, RS-232C control, HDMI-CEC,HDMI (3), Composite Video In (1), Analog Audio In (1), Digital Audio Out (1), USB (2), Ethernet (1),. Make- SONY/SAMSUNG/LG complete in all respects with the prior approval of Engineering in charge.

PVC Box for camera Supply and Installation: P/F of PVC BOX 5x5 of camera Fixing Make: Standard or equivalent make complete in all respects with the prior approval of Engineering in charge.

HDMI Cable 10 Mtr 4 K HDMI Cable Make: Honneywell/Cadyce/Zebronics complete in all respects with the prior approval of Engineering in charge.

Raceway Supply & Installlation: of Heavy Duty Floor race way (19L*9w*CM) Make- Tarkas/Serplex/Dolphy complete in all respects with the prior approval of Engineering in charge.

RJ 45 Supply and Installation: RJ 45 Connector Box, Housing: PC, UL94V-2, transparent color, Contact Terminal: Copper Alloy, Finished: 03MU micro-inch gold plating, Use for 24-26 AWG stranded wires, meet wiring scheme T568A/T568B, RJ 45 connector with installation Make- D-Link/Digisol/Commscope complete in all respects with the prior approval of Engineering in charge.

P2P Connectivity Supply and Installation: P2P Connectivity with 64MB DDR2 RAM, 8MB Flash, Qualcomm Atheros Enterprise AR9350B 560MHz CPU, MIPS 74Kc. · 1 10/100Mbps Shielded Ethernet Port (LAN0, Passive PoE in) Interface- 1 10/100Mbps Shielded Ethernet Port (LAN1, Passive PoE Passthrough ) 1 Grounding Terminal 1 Reset Button. Passive Power over Ethernet via LAN0 (+4,5pins; -7,8pins). Input voltage range: 16-27VDC (24V Passive PoE Adapter is provided). Power Draw- 11 Watts Max. Protection- 15KV ESD Protection. Enclosure-Outdoor ASA stabilized plastic material. Wireless Standards IEEE 802.11a/n, Proprietary Protocol TDMA Mode, Operating Frequency 5.15~5.85GHz, Wireless Speed Up to 300Mbps (40MHz,Dynamic) Up to 144.4Mbps (20MHz,Dynamic) Up to 72.2Mbps (10MHz,Dynamic) Up to 36.1Mbps (5MHz,Dynamic). Maximum Transmit Power 27dBm/500mw (Adjustable power by 1dBm), Operation Modes AP / Client / Bridge / Repeater / AP Router Mode /AP Client Router (WISP Client Mode, Wireless Security WPA/WPA2, WPA-PSK/WPA2-PSK (AES/TKIP) Encryption, 64/128/152-bit WEP Encryption, Gain- 13dBi, Beamwidth - 45° (H-Plane) / 30° (E-Plane), VSWR 1.6 Max, Polarizations Horizontal/Vertical, Cross-pol Isolation 18 dB Min. Certication CE, FCC, RoHS, IPX5. Operating Temperature: -30°C~70°C (-22°F~158°F) Storage Temperature: -40°C~70°C (-40°F~158°F) Operating Humidity: 10%~90% non-condensing Storage Humidity: 5%~95% non-condensing. Make- TP-Link/Hikvision/Ubiquiti complete in all respects with the prior approval of Engineering in charge.

Electric Cable Supply,Laying & Testing: 3*1.5 sqmm wire (3 pair cable), Flame Retardent(FR), Multistrand. Make- Polycab/Havells/KEI complete in all respects with the prior approval of Engineering in charge.

Bidder Name

Amount

OL TECH SOLUTIONS (GSTN-NA) BID ID -1258721

Z Eye Network Solutions Pvt. Ltd. (GSTN-NA) BID ID -1258720

Z Eye Network Solutions Pvt. Ltd. (BID ID -1258720)

Z Eye Network Solutions Pvt. Ltd. (BID ID -1258720)