REPAIR/MAINT OF SUBMERSIBLE PUMP SET MONO BLOCK PUMP SET HORIZONTAL SUBMERSIBLE PUMP SET WATER FOUNTAIN DOL / STAR DELTA STARTER AND OTHER MACHINARIES AND REPAIR/ REPLACEMENT OF AUTOMATION SYSTEM AT VARIOUS WATER SUPPLY INSTALLATION IN THE AREA OF AG

Amount

Dismantling of Oil immersed starter electrically & mechanically of capacity 7.5 HP to 30 HP of any make /size and transporting from Pump House to Contractor's work shop for carryout necessary repair and overhauling, including re-assembling complete all as specified and directed. Note:- (i) New spares/ parts shall be measured & paid separately for unserviceble parts under appropriate items listed here-in-after. (ii) Quoted rate shall be deemed included of transporting, repair, overhauling and replacement of spares complete. (iii) unserviceble parts shall be measured under sch of credit.

Supply only set of fixed and moving Contact complete all as specified and directed

Supply only of base Plate assembly complete all as specified and directed

Supply only set of auxiliary switch I No (Normal open contact) + 1 NC (Normal closed contact) complete all as specified and directed

Supply only magnet coil with auxiliary winding rated 415V, AC, 50 Hz complete all as specified and directed

Supply only thermal overload relay type RB-1 63 range 25 to 40 Amp or 36 to 60 Amp complete all as specified and directed

Supply only start & Stop Switch complete all as specified and directed

Supply only thermal time delay, relay without transformer type RZ-12 having actuating time range 3 to 12 second complete all as specified and directed

Supply only kit kat fuse suitable for 25 HP starter complete all as specified and directed

Supply only terminal links RYB & Delta complete all as specified and directed

M & L for rewinding of unserviceable / burnt auto transformer with existing size of winding wire complete all as specified and directed

Supply only reset push button assembly complete all as specified and directed

Transportation of submersible pump and motor set complete 20 HP to 30 HP 3 phase, from pump house to contractor's work shop, dismantling for carrying out necessary repairs / renewal of parts of motors or pump and reassembling complete motors/pump sets & depositing the same after necessary repair to site complete all as directed. Note:- (i) New spares/parts shall be measured & paid separately under appropriate items listed here-in-after. (ii) Quoted rate shall be deemed included of transporting, repair, overhauling and replacement of spares complete. (iii) unserviceble parts shall be measured under sch of credit.

M&L for cutting out the burnt existing winding of stator of submersible motor of any make and rewinding with the same size of , copper winding wire, etc as per existing all as specified and directed.

labour only for straightening of the slots of stator of submersible motor complete all as specified and directed

Supply only thrust bearing with block complete assembly for submersible motor

M&L for Renewal only of worn out gun metal bushes for submersible motor as per manufacturer's design complete all as specified and directed

Supply and fixing in repairs PVC sheathed and PVC insulated, flat, copper conductor submersible cable 3 core of 6 sqmm size, 8 mtr long complete with suitable clips.

Supply only sand guard of submersible motor complete all as specified and directed

Supply only sleeves of end plates of submersible motor, complete all as specified and directed

Supply only cable grommet (guard) complete all as specified and directed

Supply only water seal complete all as specified and directed

Supply only of Wedges of slots complete set for motor all as specified and directed

Complete overhauling of submersible pump by carrying out, balancing of pump shaft and cutting of key slots, repairs to bowl assembly, rethreading of wornout studs holes and provding over size studs with nuts complete all as specified and directed.

Re-metaling of motor shaft, turning to bring it to original size and shape and polishing of shaft of submersible motor complete all as directed

S & F in repair of broken PUMP shaft with new piece, making key slot, grinding to make coupling size, and balancing the rotor complete all as specified and directed.

Supply & fixing in repair coupling of submersible motor and pump with key complete all as specified and directed

Supply only bowl bushes complete all as specified and directed

Supply only neck ring complete all as specified and directed

Supply only steel distance pieces & key complete all as specified and directed

Supply only impellor gun metal as per existing complete all as specified and directed

Supply only cast iron, bowl complete all as specified and directed

Supply only CI, non return valve of required dia complete all as specified and directed

Jointing of 3 core cable of any size by using puncture/ rubber compound roll & tape / Sealing compound

Complete removal of old painted surfaces of motor and pump set and applying two coat of synthetic enamel paint (1st quality) over a coat of metal primer (hammer tone finish) all as specified.Note:- Painting shall be done by spray machine.

Transportation of submersible pump and motor set complete 15 HP/10/7.5 HP 3 phase, from pump house to contractor's work shop, dismantling for carrying out necessary repairs / renewal of parts of motors or pump & depositing the same after necessary repair, reassembling complete to site all as directed. Note:- (i) New spares/parts shall be measured & paid separately under appropriate items listed here-in-after. (ii) Quoted rate shall be deemed included of transporting, repair, overhauling and replacement of spares complete. (iii) unserviceble parts shall be measured under sch of credit.

M&L for cutting out the burnt existing winding of stator of submersible motor of any make and rewinding with the same size of , copper winding wire, etc as per existing all as specified and directed.

Straightening only of the slots of stator of submersible motor complete all as specified and directed

Supply only thrust bearing with block complete assembly for submersible motor

Renewal only of worn out gun metal bushes for submersible motor as per manufacturer's design complete all as specified and directed

Supply and fixing in repairs PVC sheathed and PVC insulated, flat, copper conductor submersible cable 3 core of 6 sqmm size complete with suitable clips.

Supply only sand guard of submersible motor complete all as specified and directed

Supply only sleeves of end plates of submersible motor complete all as specified and directed

Supply only cable grommet (guard) complete all as specified and directed

Supply only water seal complete all as specified and directed

Supply only studs with nuts of required length & dia , complete all as specified and directed

Re-metaling of motor shaft, turning to bring it to original size and shape and polishing of shaft of submersible pump complete all as directed

Supply & fixing in repair coupling of submersible motor and pump with key complete all as specified and directed

M&L for repair of submersible pump by carry out, balancing of pump sgaft and cutting of key slots, repair to bowl assmebly, rehreading of wornout studs holes nd providing over size studs with nuts complete all as sepcified and directed.

Supply only bowl bushes complete all as specified and directed

Supply only neck ring complete all as specified and directed

Supply only steel distance pieces & key complete all as specified and directed

Supply only impellor gun metal as per existing complete all as specified and directed

Supply only cast iron, bowl complete all as specified and directed

Supply only CI, non return valve of required dia complete all as specified and directed

Supply only Head extension (cast iron ) complete all as specified and directed.

Jointing of 3 core cable of any size by using puncture/ rubber compound roll & tape / Sealing compound

Complete removal of old painted surfaces of motor and pump set and applying two coat of synthetic enamel paint (1st quality) over a coat of metal primer (hammer tone finish) all as specified. Note:- Painting shall be done by spray machine.

Transportation of Centrifugal pump set/ monoblock pumpset/ Horizontal submersible pump set- 10HP to 20HP, AC, 3 phase, 415/420 V from pump house at any location/Yard transporting to contractor's work shop, dismantling for carrying out necessary repais / renewal of parts of pump and depositing the same after repair, reassembling complete to site all as directed. Note:- (i) New spares/parts shall be measured & paid separately under appropriate items listed here-in-after. (ii) Quoted rate shall be deemed included of transporting, repair, overhauling and replacement of spares complete. (iii) unserviceble parts shall be measured under sch of credit.

Cutting out the existing winding of the motor, opening of winding, re winding of motor with same size of winding wire as existing including varnishing, drying and making connection complete all as specified and directed.

Repairing of pump by rethreading of worn out studs holes and S&F over size studs with nut and washer complete all as specified and directed.

Supply only driven end bearing of motor shaft complete all as specified and directed.

Supply only non driven end bearing of motor shaft complete all as specified and directed.

Rematelling and repairing of pump shaft , complete all as specified and directed

Supply only gun metal / stainless steel bush of pump shaft complete all as specified and directed.

Supply only of gland and packing complete all as specified and directed.

Supply only CI impeller of similar make as directed

Supply only connection plate complete all as specified and directed.

Supply only coupling with studs between motor & pump complete all as specified and directed.

Supply only cover sleeve of motors as per existing size complete all as directed

Re-metaling of pump shaft, turning for bring it to Internal dia size of bearing in rear end cover complete all as directed

Supply only neck ring complete all as specified and directed

Removing of Centrifugal pump set/ monoblock pumpset/ mono sub (openwell) pump set from its existing position and re-fixing of repaired pump set including renewal of worn out nuts & bolts and electric connection complete all as specified and directed.

Complete removal of old painted surfaces of pump set and applying two coat of synthetic enamel paint (1st quality) over a coat of metal primer (hammer tone finish) all as specified. Note;- Painting shall be done by spray machine.

Transportation of Centrifugal pumpset/ monoblock pump sets/ mono sub. pump set 1 HP to 3 HP, AC, Single phase, 220/240 V from pump house at any location/Yard in Cantt area contractor's workshop, dismantling for carrying out necessary repais / renewal of parts of pump and depositing the same after repair, reassembling complete all as specified. Note:- (i) New spares/parts shall be measured & paid separately under appropriate items listed here-in-after. (ii) Quoted rate shall be deemed included of transporting, repair, overhauling and replacement of spares complete. (iii) unserviceble parts shall be measured under sch of credit.

Cutting, opening of winding, re- winding of Centrifugal pumpset/ monoblock pump sets/ mono sub. pump set of any make and rewinding with same size of copper winding wire, varnishing, backing complete as directed.

Repairing of pump by rethreading of worn out studs holes and S&F over size studs with nut and washer. Balancing and repairing of pump shaft.

Supply only water seal and packing complete

Supply only driven end bearing of pump shaft

Supply only non driven end bearing of pump shaft

Supply only cooling fan

Supply only cooling fan cover

Supply only CI impeller of as make all as directed

Supply only connection plate

Supply only capacitor of required capacity

Removing of Centrifugal pumpset/ monoblock pump sets/ mono sub. pump set from its existing position and re-fixing of repaired pump set including replacement of worn out nuts & bolts and supply and fixed nuts, bolts and electric connection complete all as specified and directed.

Complete removal of old painted surfaces of pump set and applying two coat of synthetic enamel paint (1st quality) over a coat of metal primer (hammer tone finish) all as specified. Note:- Painting shall be done by spray machine.

Supply and fixed in repairs Single Phase Preventor all as specified and directed.

Supply and fixed in repairs star delta starter fully automatic oil cooled with auto transformer and first filling of transformer oil complete with suitable size cable for connection between starter to auto transformer suitable for 20 to 25 HP, 3 Phase, 415 V electric motar including necessary connection and fixed on stand made out of angle iron 40 X 40 X 4 mm size complete all as specified and directed.

Supply and fixed in repairs star delta starter fully automatic oil cooled with auto transformer and first filling of transformer oil complete with suitable size cable for connection between starter to auto transformer suitable for 30 to 35 HP, 3 Phase, 415 V electric motar including necessary connection and fixed on stand made out of angle iron 40 X 40 X 4 mm size complete all specified and directed.

M&L Mild screw nut, bolts with washer 12 mm dia and 100 mm long ( Machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends , each screwed end to be fitted with washers and one hexagonal or square nut complete all as specified and directed

Supply & fix in repairs electronic control timer type ET-100 of suitable capacity as required at site.

S&F of submersible flat copper stranded cable 1100 Volt grade of size 16 sqmm 3 core complere all as specified and directed.

S&F of submersible flat copper stranded cable 1100 Volt grade of size 10 sqmm 3 core complere all as specified and directed.

S&F tail pipece in replacement Made out MS ERW pipe heavy Grade 100 mm dia upto 1.5m in length suitable for submersible pump upto 30 HP including making arrangements for fixing of tie rod, cutting thread & welding flange all as sper siterequirement complete all as specified.

Disconnection of submersible pump set of any size from existing system water supply & electrical and Taking out /Uplifting the U/S pump set from deep borewell with disconnected from lowering pipe line of any size with manual or suitable electric driven chain pully upto 240 ft depth reassembling after neccesary repair and re-lowering the pump set in same borewell re-connection of complete all as specified and directed. Note:- i) Repair of U/s pump set will be paid separately. (ii) All type of T/P required to complete the job will be arranged by contractor. (iii) Job will be done round -o-clock continued as per site requirement as directed by Engr-in-Charge. (iv) Delay in job will be charged on the basis of Rs. 500/- per hour. (v) Items required for motor connection such as PVC insulation tape, tie rod, valcanised rubber / puncture tube etc will be provided by the contarctor to complete the work and rate as deemed to be quoted in unit rate no extra payment will be made to the contractor.

S&F (in repair) rubber gasket 3 mm thick (packing ring) suitable for 100 bore flange lowering pipe cut type complete all as specified and directed

S&F (in repair) rubber gasket 3 mm thick (packing ring) suitable for 150 bore flange lowering pipe cut type complete all as specified and directed

S & F in repair , submersible pump assy upto 12 stage not less than 07 stages including bearing bush , shaft , bowls , thrust bearing , bronze impellers of pum etc comprising / suitable arrangement for directly coupled with motor of cap 15 Hp cast iron body suitbale for 300 mm dia borewell multistage , discharge of 600-800 LPM at 91 mtr Head and complete with suitable end connecting tail piece , NRV complete all as specified and directed .

S & F In repair, submersible motor assy of capcity 15 Hp with stator including insulated copper winding , rotor , bearing , bush , thrust plate terminal plate and casing of motor comprising with arrangement of direclty coupled with pump cast iron body elecric driven 415V, TP along with connecting tail piece , NRV and submersible cable aluminium 7.5 Rm complete all as specifed and directed.

S & F in repair , submersible pump assy upto 12 stage not less than 07 stages including bearing bush , shaft , bowls , thrust bearing , bronze impellers of pum etc comprising / suitable arrangement for directly coupled with motor of cap 25 Hp cast iron body suitbale for 300 mm dia borewell multistage , discharge of 600-800 LPM at 91 mtr Head and complete with suitable end connecting tail piece , NRV complete all as specified and directed .

S & F In repair, submersible motor assy of capcity 25 Hp with stator including insulated copper winding , rotor , bearing , bush , thrust plate terminal plate and casing of motor comprising with arrangement of direclty coupled with pump cast iron body elecric driven 415V, TP along with connecting tail piece , NRV and submersible cable aluminium 7.5 Rm complete all as specifed and directed.

Attending the complaint of Oil immersed star delta starter with auto transformer upto 50 HP capacity And AMF Panel round the clock including Sunday & Holiday at any location in Lucknow Cantt area with in specified time not more than two hours complete all as specified and directed. (Note :- (i) Work requisition as per Annx I duly signed by all concerned kept on record and shall be submitted to GE alongwith RAR. (ii) Spare parts upto cost of Rs. 100.00 shall be included in the unit rate quoted by the bidder. (iii) Any other spare parts shall be measured and paid separately under appropriate items. (iv) Complaint shall be recitifed within 72 Hours from the date of complaint, failing which recovery shall be charge @ Rs. 50.00 per complaint per day.)

Daily maintenance of automation system at 16 nos pump houses (servicing and management distribution network) automatic water supply system installed at different location at Lucknow cantt by deploying adequate manpower including repair/replacement of mechanical & Electrical parts of actuater butterfly valves / Electric & electronic parts & components of PLC based control panal complete all as specified and directed.(Make:- RDS/Simcon) Note:- (i) Each pump house shall be cleaned /maintained daily under supervision of E1C (ii) Fixing of defective spares / components are deemed to be included in the unit rate but cost of spares /components will be paid under respective items here in after (iii) Daily maintenance register shall be maintained for each pump house and shall be signed by rep of contractor and the Engineer in Charge after doing necessary maintenance)

Supply only Relay -04 C/O , 220V AC complete all as specified & directed.

Supply only Relay -04 C/O , 24V DC complete all as specified & directed.

Supply only Relay Port for fixing of Relay -04 C/O

Supply only indicator lamp of 24 V DC colour: Red/ Yellow/ Green complete all as specified & directed.

Supply only push button with LED indicator ,240 V AC, color : Red / Yellow / Green complete all as specified & directed.

Supply only of SMPS 24 V DC, 2.4 Amp Make:- TELEMACNIQUE/NHP/Minilec complete all as specified & directed.

Supply only of Limit Switch for Actuator Suitable for 80 mm /150mm /200mm dia Butterfly Valve complete all as specified & directed.

Supply only expansion / unitronics / allen Bradley / Siemens / Mitsubishi adapter / HMI of the PLC.

S&F water level controller PCB-5 level Make: Splash/SM Instrimentation/ICS complete all as specified & directed.

Supply only step down transformer input 230 V and output 12 V DC, 2 A rating,

M & L for panel wiring using PVC insulated 0.5 Sqmm copper wire as per direction by E1C.

Servicing of motorised Butterfly Valve-80 mm /100 mm i.e. Removing , cleaning, checking for wear & tear , refixing,testing,installing,comissioning as specified & directed by the Enginee r- in-Charge. Note:- Spares shall be measured and paid separately if needed.

Servicing of motorised Butterfly Valve-150/200/250 mm i.e. Removing , cleaning , checking for wear & tear , refixing, testing,installing,comissioning as specified & directed by the Enginee - in-Charge.Note:- Spares shall be measured and paid separately if needed.

Supply & Fixing in replacement of motorised Butterfly Valve-100mm, testing, installing, comissioning as specified & directed by the Enginee r- in-Charge.

Supply & Fixing in replacement of motorised Butterfly Valve-150mm, testing, installing, comissioning as specified & directed by the Engineer- in-Charge.

Supply & Fixing in replacement of motorised Butterfly Valve-200mm, testing, installing, comissioning as specified & directed by the Enginee r- in-Charge.

S & F only capacitor for Actuator suitable for 80mm/150mm/250mm Butterfly valve complete all as specified and directed.

S & F only Actuator Adoptor for 150 mm dia butterfly Valve with key complete all as specified and directed. (Make:-Ritetork/Hasse hofener)

Supply only Electric motor suitable for Actuator for 100 mm dia butterfly Valve complete all as specified and directed. .(Make:- SD Tork / Emtork / Hassel / SM Instrumentation)

Supply only Electric motor suitable for Actuator for 150 mm dia butterfly Valve complete all as specified and directed. .(Make:- SD Tork / Emtork / Hassel / SM Instrumentation)

Supply only Electric motor suitable for Actuator for 200 mm dia butterfly Valve complete all as specified and directed. .(Make:- SD Tork / Emtork / Hassel / SM Instrumentation)

Supply only Electric motor suitable for Actuator for 250 mm dia butterfly Valve complete all as specified and directed. .(Make:- SD Tork / Emtork / Hassel / SM Instrumentation)

Supply, Installation, testing & commissioning of pressure switch in replacement alongwith all necessary installation accessories like GI barrel piece, double nipple etc with following specifications (a) 0.6 Kg/sqcm (b) Enclosure weather proof IP 65. Make:- SWITZER/INDFOSA/DANFOSS.

Supply,installation, Testing & commissioning PLC having 12 input and 9 output with inbuilt power supply and inbuilt HMI including programming auxiliary supply 24 V DC, installation complete all as specified & directed. Make : UNITRONICS / ALLEN BRADLEY / SIEMENS / MITSUBISHI

Supplying, laying or fixing in replacement , jointing and testing solid PVC insulated , 10 pairs, individual shielded for interference rejection, armoured PVC sheathed 1100 Volts garde 0.5 sqmm instruemental copper cable ISI-5608 marked ,complete all as specified laid in trenches/ laid under floor or fixed naked with walls / on poles/ in ducts /in GI pipes etc. including nuts, bolts and washers complete all as specified and directed.

Supply & fixing in replacement six core, 1.5 sqmm nominal cross sectional area multistranded armoured copper conductor cables, 1100 volts grade heavy duty cable PVC insulated and PVC sheathed, laid in trenches/ laid under floor or fixed maked with walls / on poles/in ducts/in GI pipes etc complete all as specified,

Supply & fixing in replacement five pair, 0..5 sqmm nominal cross sectional area mulistranded copper conductor cables, 1100 volts grade heavy duty cable PVC insulated and PVc sheathed, laid in trenches/ laid under floor or fixed maked with walls / on poles/in ducts/in GI pipes etc complete all as specified,

Supply, Installation, Testing and commissioning of motor actuated butterfly valve in replacement with the following specifications including all accessories mentioned as under (a) Valve size 300mm dia (b) Designed line pressure 4 kg/Sqcm (c) Operating Angle : 90 degrees (d) Disc material CI with nylon coating (e) Limit switches : 02 Nos for open and close (f) Mounting : Splash proof-Direct on valve (g) Input Supply : 230V, AC, 50 HZ (h) In built wireless modem compatibility for remote communication (j) Valve position indication with an output of 4-20m A (k) The actuator should be capable of accepting 4-20m A of input of regulating purposes (l) Mannual Operation : Hand Wheel Make : RITETROK/EMTORK/HASSEL

Supply, Installation, Testing and commissioning of motor actuated butterfly valve in replacement with the following specifications including all accessories mentioned as under (a) Valve size 250 mm dia (b) Designed line pressure 4 kg/Sqcm (c) Operating Angle : 90 degrees (d) Disc material CI with nylon coating (e) Limit switches : 02 Nos for open and close (f) Mounting : Splash proof-Direct on valve (g) Input Supply : 230V, AC, 50 HZ (h) In built wireless modem compatibility for remote communication (j) Valve position indication with an output of 4-20m A (k) The actuator should be capable of accepting 4-20m A of input of regulating purposes (l) Mannual Operation : Hand Wheel Make : RITETROK/EMTORK/HASSEL

Supply, Installation, Testing and commissioning of motor actuated butterfly valve in replacement with the following specifications including all accessories mentioned as under (a) Valve size 200 mm dia (b) Designed line pressure 4 kg/Sqcm (c) Operating Angle : 90 degrees (d) Disc material CI with nylon coating (e) Limit switches : 02 Nos for open and close (f) Mounting : Splash proof-Direct on valve (g) Input Supply : 230V, AC, 50 HZ (h) In built wireless modem compatibility for remote communication (j) Valve position indication with an output of 4-20m A (k) The actuator should be capable of accepting 4-20m A of input of regulating purposes (l) Mannual Operation : Hand Wheel Make : RITETROK/EMTORK/HASSEL

Supply, Installation, Testing and commissioning of motor actuated butterfly valve in replacement with the following specifications including all accessories mentioned as under (a) Valve size 150 mm dia (b) Designed line pressure 4 kg/Sqcm (c) Operating Angle : 90 degrees (d) Disc material CI with nylon coating (e) Limit switches : 02 Nos for open and close (f) Mounting : Splash proof-Direct on valve (g) Input Supply : 230V, AC, 50 HZ (h) In built wireless modem compatibility for remote communication (j) Valve position indication with an output of 4-20m A (k) The actuator should be capable of accepting 4-20m A of input of regulating purposes (l) Mannual Operation : Hand Wheel Make : RITETROK/EMTORK/HASSEL

Supply, Installation, Testing and commissioning of motor actuated butterfly valve in replacement with the following specifications including all accessories mentioned as under (a) Valve size 100 mm dia (b) Designed line pressure 4 kg/Sqcm (c) Operating Angle : 90 degrees (d) Disc material CI with nylon coating (e) Limit switches : 02 Nos for open and close (f) Mounting : Splash proof-Direct on valve (g) Input Supply : 230V, AC, 50 HZ (h) In built wireless modem compatibility for remote communication (j) Valve position indication with an output of 4-20m A (k) The actuator should be capable of accepting 4-20m A of input of regulating purposes (l) Mannual Operation : Hand Wheel Make : RITETROK/EMTORK/HASSEL

Supply and fixing of cable joint Kit with heat shrink sleeves complete all as specified and directed

Supply installation, testing & commissioning of Magnetic Level sensors inside tank/sump Make: CRYSTAL/S M INSTRUMENTATION/ MAHALAXMI

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth for laying of cables, pipes etc. and getting out including trimming the sides and forming bottom surfaces to required levels in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, and well ramming in layer not exceeding 25 cm thick in soft/loose soil complete all as specified and directed.

Removing excavated material ( soils) not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified.

Material and labour for river sand, washed and screened dry for cushioning to under ground cable in trenches below and around under ground cable including spreading and levelling complete as specified and directed. Note :- Punned thickness shall only be considered for payment

M&L laying well burnt old size bricks, straight or curved on plan , laid flat with width equal to length of brick , laid dry over electric cable for protection all as specified.

Supplying and fixing (in repair) 80mm bore Galvanised mild steel pipe /tubing, light grade complete with all fittings, laid in trenches / under roads, drain, paths, fixed to poles/ walls with Mild steel clamps , bolts , nuts and washers complete all as specified and as directed. Excavation & Earth work shall be measured and paid separately)

M/S S.B. Singh and Sons

Sanjay Traders

Microsys Automation India

M/S. KUMAR CONSTRUCTION CO.

M/s Singh enterprises

ms singh construction

M/s Bapujee Builders and Traders