PROVISION OF 03 LANE SLIPWAY 500 TON CAPACITY AT PORT BLAIR

Amount

GENERAL SUMMARY NOTE: Schedule ‘A’ Part I to XV are prepriced by MES under Ser No. 2.00 to 11.00. Bidders shall insert their lumpsum amount in the Green coloured field under Col-6 only.

Lumpsum price worked out by the contractor for "BUILDINGS/ STRUCTURES” as listed in Schedule ‘A’ Part - I, inserted by MES

Lumpsum price worked out by the tenderer for "Internal Water Supply " as listed in Schedule ‘A’ Part-II

Lumpsum price worked out by the tenderer for "INTERNAL ELECTRIFICATION" as listed in Schedule ‘A’ Part-III

Lumpsum price worked out by the tenderer for "EXCAVATION/ EARTHWORK & SITE CLEARANCE " as listed in Schedule 'A' Part-IV

Lumpsum price worked out by the tenderer for "SEWAGE DISPOSAL" as listed in Schedule 'A' Part-V

Lumpsum price worked out by the tenderer for "RCC RETAINING WALL" as listed in Schedule 'A' Part-VI

Lumpsum price worked out by the tenderer for "EXTERNAL WATER SUPPLY" as listed in Schedule 'A' Part-VII

Lumpsum price worked out by the tenderer for "EXTERNAL ELECTRIFICATION" as listed in Schedule 'A' Part-VIII

Lumpsum price worked out by the tenderer for "DECK STRUCTURE" as listed in Schedule 'A' Part-IX

Lumpsum price worked out by the tenderer for "SUB STRUCTURE" as listed in Schedule 'A' Part-X

Lumpsum price worked out by the tenderer for "EXTERNAL FIRE FIGHTING" as listed in Schedule 'A' Part-XI

Lumpsum price worked out by the tenderer for "FIRE ALARM SYSTEM" as listed in Schedule 'A' Part-XII

Lumpsum price worked out by the tenderer for "INTERNAL FIRE FIGHTING" as listed in Schedule 'A' Part-XIII

Lumpsum price worked out by the tenderer for "LIGHTENING PROTECTION" as listed in Schedule 'A' Part-XIV

Lumpsum price worked out by the tenderer for "TELEPHONE CONDUIT" as listed in Schedule 'A' Part-XV

Subtotal

SCH 'A' PART XVI MISCELLANEOUS ITEMS NOTE: Schedule ‘A’ Part - XVI is not prepriced by MES and prepriced rate indicated as 0.00 under Col.5 signifies this fact only. Bidder shall insert their rates in Green colour filled under Col-6.

INTERNAL WATER SUPPLY : S&F Angular Stop Cock with wall flange for WHB for Urinals Make : Cat Part No CON-059 FTK of Jaquar or Equivalent in Marc ,GEM, CERA Sunitoro, SOMA.

Supply and fix Two way 15 mm bore Bib Cock make : Cat Part No CON-041KN of Jaquar or Equivalent in Marc ,GEM, CERA Sunitoro, SOMA.

S&F 15mm bore dia pillar cock long neck Make : jaguar Cat Part No CON-021 KN or equivalent Marc ,GEM, CERA Sunitoro, SOMA.

S& F Heath Faucet to be fitted along with Bip Cock Make : Cat Part No ALD-CHR-585 of Jaquar or Equivalent in Marc ,GEM, CERA Sunitoro, SOMA.

S&F chromium plated Urinal spreader suitable for urinals complete all as specified and directed (Make :Jaguar Cat Part No ALD-CHR-1043 or equivalent in Hindware/ Prayag Cat No. BEA-25)

Internal Electrification : S & F TV socket with cable grip all as directed by Engr-in-Charge by Make -L&T/Havells/HPL

Supply and fix ceiling fan, 5 star rating with BLDC motor suitable for working of AC 230 V, 50 HZ, 1400 mm sweep with remote controller, ,down rod of length up to 1 mtr long and canaopy, colour of milky white including ceiling hook for fixing of fan on ceiling including providing 1.5 Sqmm 3 Core white colour PVC insulated copper conductor cable from ceiling rose to fan complete all as specified and directed by engineer-in-charge Make Atomberg, Havells, Orient Usha

S&F wall mounting fan 450 mm sweep single phase 230 Volt 50 Hz energy efficient smooth functioning including fixing arrangements with Anchor Fasteners, 1.5 Sqmm 3 Core wire with plug top for connecting all as directed by Engr-in-Charge.Make ;Crompron/Bajaj/Usha

S&F Exhaust fans 300 mm sweep single phase 230 Volt 50 Hz heavy duty 1400 rpm energy efficient smooth functioning with sutable size of louver including fixing arrangement with anchor fasteners, provision of three core 1.5 Sqmm white colour PVC insulated copper conductor cable from ceiling rose to fan, opening of hole and making good the surface by cement mortar, etc all as directed by Engr-in-Charge .Make ;Crompron/Bajaj/Usha

S&F Exhaust fans 450 mm sweep single phase 230 Volt 50 Hz heavy duty 1400 rpm energy efficient smooth functioning with sutable size of louver including fixing arrangement with anchor fasteners, provision of three core 1.5 Sqmm white colour PVC insulated copper conductor cable from ceiling rose to fan, opening of hole and making good the surface by cement mortar, etc all as directed by Engr-in-Charge .Make ;Crompron/Bajaj/Usha

Supply and Fix LED type tube light fittings 4 feet long 1x18 W 230V ,decorative ultra slim square profile liner LED lighting fixture with extruded polycarbonate envoirnmental friendly, energy efficient tube light life time 40,000 burning Hrs, lumen output 1600lm, color temp-6000K, CRI-80, power factor >0.9 complete & prewired for LED tube complete fixed to wall / Ceiling by suitable downrods, PVC round blocks and connection by flexible PVC cable with stranded copper conductor from ceiling rose to connector of the fitting including 1x18W LED tube complete all as specified. Make : Havells Cat No-PHOTONULLTRA+603T8SSTl18WLED865SPCor Equivalent to Wipro/Bajaj/Crompton/Philips Note : 3years Guarranty as per manufacturer instructions or lifetime 40,000 burning Hrs which ever is earlier as applicable.

S & F 9 Watt LED fittings for Mirror with surge protection of 2 KV with wide voltage protection 160-360 Volt complete all as directed by Engr-in-Charge . Make Philips/Bajaj/LUKER

S & F building street light 25 Watt capacity LED including electronic driver IP 65 protection ,fixing with suitable size of brakets 1.2 mtr long bend to shape including clamp nut and bolt ,connected fron celing rose or existing point all as directed by Engr-in-Charge.Make Philips/Bajaj/Crompton

S & F LED Flood light 120 Watt Capacity mounting on 9 to 15 mtr hight with suitable size clamp including electronic driver and surge protection, IP 65 , high power flood optics to be ensure uniform distribution ,maintenance free system all as directed by Engr-in-Charge .MakePhilips/Bajaj/Crompton

Supply and fix Sheet steel factory made double door, powder coated MCB DB with bus bar 200Amps,Neutral link, Earth bar, double door type SPN 6 Way 220 Volt, MCB as a Incomer complete all as directed. Make : L&T / Legrand / Schneider / ABB

Supply and fix Sheet steel factory made double door, powder coated MCCB DB with bus bar 400 Amps,Neutral link, Earth bar, IP54 Protection, double door type TPN 8(8+8+8 out going) Way 415 Volt, MCCB as a Incomer complete all as directed. Make : L&T / Legrand / Schneider / ABB

Supply and fix miniature circuit breaker (RCBO/MCB,s/MCCBs) of following capacity :- Make L&T/Schinder/Legrand.

(a) MCB SPN 230 Volts, 10KA, 16 Amps 'C' curve

(b) MCB SPN 230 Volts, 10KA, 20 Amps 'C'curve

(c) MCB SP 230 Volts, 10KA, 6 to 32 Amps ' C'curve

(d) MCB TPN 415 Volts, 10KA, 16 Amps 'C'curve

(e) MCB TPN 415 Volts, 10KA, 20 Amps 'C'curve

(f) MCB TPN 415 Volts, 10KA, 32 Amps 'C'curve

(g) MCB TPN 415 Volts, 10KA, 63 Amps 'C'curve

(h)MCB TP 40 Amps, 10 KA Capacity

(j) MCB TP 63 Amps, 10 KA Capacity

(k) MCCB 4 Pole 415 V 63 Amps 25 KA Capacity

(l) MCCB 4 Pole 415 V 100 Amps 25 KA Capacity

(m) MCCB 4 Pole 415 V 125 Amps 25 KA Capacity

(n) MCCB 3 Pole 160 Amps 415 V 25 KA Capacity

M&L for earthing complete with Galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below GL) with top edge of earth plate not less than 1.5 Mtr below normal ground level, earth plate surrounded from all sides by 15cm thick and packed layer of charcoal dust and common salt filling in alternate layers and electrode connections by using Galvanised earth strip 32x6mm connected by means of bolts, nuts, check nuts and washer of galvanised iron or steel, provision of 15 mm dia GI pipe medium grade for protection of GI earth wire and 20mm dia GI pipe medium grade for watering arrangement and PCC (1:3:6) , type C1 chamber, MS funnel, wire gauge, 50 mm thick RCC 1:2:4, type B1 earth pit cover with 6 Nos, 8 mm dia high strength deformed steel TMT bars on both ways including necessary excavation in any type of soil, returning, filling in, removal of surplus soil to distance n exc 50 mtr, provision of charcoal and salt complete all as shown in electrical plate No 3 of schedule Part-I Note: (i) Cost of GI earth strip and GI protection pipe upto 7.5mtr length shall be deemed to be included in the rate quoted for this item (ii) The unit rate shall also includes for Wire mesh, funnel, excavation, PCC chamber pit, test point

Supply, installation, test and commissioning of chemical gel earthing ,dual pipe system technology having earth resistance <3 ohm comprises of not less than 3.0 mtr long earthing electrode made of two co-axial MS pipe duly hot dip galvanised wire lead terminal of 30x10 mm size at top of electrode, minimum dia of outer pipe will be 50 mm and minimum dia of inner pipe will be 25 mm to achieve desired earth results, joined together to enhancing the service life and performance of overall earthing system. cavity inbetween the co-axial pipes duly filled with crystalline conductive compounds for current for current dissipiation and enhance anti corrosive properties, the cavity arround the electrode duly filled with back fill compounds (BFC) as per IS-3043, sufficent water shall be poured into the earth pit untill the BFC take the form of paste/gel, BFC must have hygroscopic property to retain moisture for longer time to reduce earthing resistance of electrode and to provide constant output, BFC must be filled such that with no air gaps in the filled area complete earthing must be free from periodic watering or any recharge during its entire life and should be remain effective in all types of soils including dry soils and rocky conditions, electrodes top terminal duly connected with earth strip with SS nuts, bolts, washers, etc elctrodes top terminal alongwith earthing strips duly prtected with factory made earth pit and pit cover made of light weight polymer, having locking arrangements with and including making bore hole of desired size in any type of soil surface complete and all as directed. Make: JK gel earthing/ Tercel earthing/JBM LPS earthing.

Note :- 1. The drawings/design data of gel earthing to achieve earth resistance <3 ohms as per ground conditions, shall be approved by accepting authority before placement of order. 2. The complete earthing will be installed, commissioned and tested by manufacturer/OEM only 3. The cost of making bore hole of desired size and depth, in rocky surface or hard soil is deemed to be included in the qouted rates and no extra payment shall be made to contractor in this effect at any stage. 4. The cost of factory made earthing is deemed to be included in the qouted rates and no extra payment shall be made to contractor in this effect at any stage.

EARTHWORK EXCAVATION & SITE CLEARANCE: Dredging in all types of soils including overburden, dense to very dense clay , silt, sand removal of surface boulder upto bottom of Deck slab whereever shown and necessary with suitable dredgers and equipment to the required lines and levels and slopes including removal and transportation of the dredged meterials and dumping the same in the designated off shore dumping areas in open sea having more than 100m depth within the parameters of 2.3 Nautical miles NE of Ross Island and 2.3 Nautical miles East of North Bay light (Approx location 11 Deg 41.5 N & 092 Deg 47.5E ) all as shown and as directed. The unit rate shall include mobilization, demobilization of plant equipment , surveys during progress of work , rail dragging of the dredged areas to specified levels after completion of dredging , operation and maintanance all plants and equipments and crafts man power and labour charges cost of materials fuel and taxes insurance etc as required and as directed.

Sand fo filling inside Coffer Dam Supply and laying crushed stone sand or M - sand filling in layers including cost of all materials , machinary , labour , watering, ramming etc, inside coffer dam upto Top level (+) 3.0 m. Note : crushes stone sand from locally available quaries will be allowed.

External Water Supply : Supply & Fix water meter 50 mm dia class - B cast iron body flanged PN 16 type class B, including gaskets, nut bolts, suitable for bulk flow of water .

S & F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part -I of capacity 10,000 ltrs along with PCC platform on deck structure, float valve 50 mm dia, etc complete all as directed . (Rates shall be inclusive of PCC platform for placing the tank).

Supply, installation, testing and commissioning indoor cubical wall mounted Panel suitable for 3 phase, 4 wire, 415 volts 50 Hz supply system with suitable size and powder coated, dust/vermin proof. The panel shall CPRI approved factory fabricated made with 2 mm thick CRCA sheet for outer shell and inner shell made out of 1.6 mm thick CRCA sheet, double door with front and back openable with locking arrangement, provision of thereaded earthing stud at bottom, inner shell shall be compartmentalized fron openable single door lockable , inner shell shall be completely vermin proof and to accommodate incoming / outgoing MCBs, starter and TPN aluminium bus bar .The TPN busbar and extensions link shall be insulated with colour coated heat shrinkable sleeves and shall be mounted on epoxy resin insulator. All control wires shall be with 1.5 sqmm multistranded copper conductor wire and shall be properly bunched, tied ferruled for proper identification and crimped with suitable size of lugs. (a) MCCB 4 Pole 40 Amp 50 Hz 415 V, 16 KA-01 No(Incoming) (b) MCB 3 Pole 32 Amp 50 Hz 415 V, 10 KA-02 No (c) DOL Starter 5 HP 3pase 440 volts - 2 Set (d) R Y B panel Indicators - 1 Set (e) Digital Multi Function Meter -1 No

Cutting the existing GI pipe line of 100mm dia and inserting GI Tee of size 100x100x80 mm complete all a sirected

DECK STRUCTURE: Supply and fixing in position cast steel bollard of 100 Tonne pull capacity as per manufacturers specifications and drawings complete with base plate and HT anchor bolts of appropriate length, nuts, washers etc, including two coats of anticorrosive paint over a coat of Zinc silicate primer, grouting with cement concrete of grade M-30 (using 20mm graded stone aggregate), under base plate, filling the cavity with concretre of grade M-30, complete all as specified and as directed.

Carrying out High strain dynamic test on working piles (0.50% of total number of piles) all as per ASTM 4945 - 17 including the mobilizing equipments required for conducting test, carrying out tests, providing the requisite data/results as per relevant methods to estimate the pile load carrying capacity along with supporting documents duly conducted by approved agency.

Carrying out Low strain Integrity test on working piles (100% of total number of piles) all as per IS 14893 latest edition, including the mobilizing equipments required for conducting test, carrying out tests, providing the requisite data/results as per relevant methods along with supporting documents duly consucted by approved agency.

Supplying and fixing in position of 3000mm long 'D D' type fenders of size 500mm x 500mm (External dimensions) and 250mm x 250mm (internal dimansions) of weight not less than 239kg/mtr complete with 180mm x 3000mm length x 20mm thick flat bar with necessary fixing arrangements like anchor bolts, nuts etc. and grouted at locations complete fixed as per manufacturer's instructions and as specified & directed by Engineer-in-Charge. Note :- (i) Make and Type of 'D D' fenders shall be SD series 500x500 fender of M/s Trelleborg Marine System or its equivalent of makes as specified in PS. (ii) The equivalent fender shall meet all the Physical, Mechanical, Technical parameters, i.e. Mechanical properties, energy criteria weight, dimensions etc. as given for SD series 500 x 500 fender of M/s Trelleborg Marine Systems.

M&L for providing two coats of Anti corrosive paint (MIO Coating) of 90 microns DFT over a coat of epoxy zinc silicate primer of 60 microns DFT after preparation of new steel surfaces with wire brushing & scrapping on Structural Steel elements

Steel formwork to sides and soffits of floor or roof beams etc flat finished fair and even including all supports from piles in offshore conditions, complete all as specified and directed.

Steel formwork to sides of walls and pedestals etc flat finished fair and even including all supports from piles in offshore conditions, complete all as specified and directed.

Steel formwork to soffits of suspended slab such as roof, floor,kerbs etc., exceeding 200mm thick for slab lat finished fair and even including all supports from piles in offshore conditions complete all as specified and directed.

S&F of MS Pawl rack over sloping track including laying and fixing all as shown on drawings as specified and as directed. Note : Measurement will be taken as per finished shape in the drawings

Forming Expansion joint of 40mm width with clear gap between structures using necesssary temporary joint filling material / formwork to concrete surfaces to full depth of joint. Note : After completion the filler material if used shall be removed to provide clear gap of 40mm between structures as per drawings

S&F Stainless Steel railing having 50 mm dia SS heavy grade SS-316 pipe baluster and SS end cap at bottom. All other rails will be of 38 mm dia SS pipe heavy grade SS-316 with end SS Cap at bottom. and 20 mm dia SS heavy grade SS-316 will be provided as intermediate support including all fittings including grouting and fixing in to slab & Polishing all as specified and directed by Engineer-in-charge.

Supply, fabricate and fixing in position Cast iron wheel/rollers all as per drawings complete with shafts and other connecting requirements to fix it with cradles of appropriate locations etc, including two coats of anti corrosive paint over a coat of Zinc silicate primer complete all as specified and as directed.

SUB STRUCTURE: Positioning and setting upon and/or shifting and setting up piling equipment required for 800mm dia piling work at each piling locations inside coffer dam for 800mm dia pile as show in the drawing and or as directed including all labour, materials, fuel, tools, equipments etc. complete (Tripod Method)

Positioning and setting upon and/or shifting and setting up piling equipment required for 800mm dia piling work at each piling locations for coffer dam for 800mm dia pile as show in the drawing and or as directed including all labour, materials, fuel, tools, equipments etc. complete (Gantry/Barge) Shifting distance - 1.10m c/c

Positioning and setting upon and/or shifting and setting up piling equipment required for 1000mm dia piling work at each piling locations for coffer dam for 1000mm dia pile as show in the drawing and or as directed including all labour, materials, fuel, tools, equipments etc. complete (Gantry/Barge) Shifting distance - 1.30m c/c

Positioning and setting upon and/or shifting and setting up piling equipment required for 800mm dia piling work at each piling locations for coffer dam for 800mm dia pile as show in the drawing and or as directed including all labour, materials, fuel, tools, equipments etc. complete (Gantry/Barge) Shifting distance - 8.00m c/c

Boring for the piles 800mm dia to the required depth through all types of soil strata including cemented sand, if any up to the founding level and stacking the bored soil at convenient place and transported to location upto a distance not exceeding 1KM as directed by GE and pile shaft cleaning and keeping of all records etc., including bentonite solution, labour, tools, equipment, fuel etc., all as per drawing, specification etc., complete all as specified and as directed . Note :- 1. If the boring tool encounters rock at an elevation higher than the termination level of the pile indicated in the drawing then the boring shall be continued into the rock from where the boring tool encounters rock first to a depth 2. In case the soil stratum at the founding level is loose the Engineer-in-charge may direct the contractor to carryout additional length of boring and payment for such additional work shall also be made under this item. 3. The sample of bored materials at regular interval shall be collected and produced for the verification of the Engineer-in-charge or his representative at no extra cost. In the event of any dispute about the type of strata bored the samples so collected shall be referred to an authorised laboratory / agency report indentified by the Engineer-in-charge and the decision of GE based on such authorised laboratory / agency report is final and binding on both the parties. However the cost of such testing shall be borne by the contractor including transportation of material. (i) Boring through all type of soil strata including cemented sand strata including cemented sand except rubble layer and hard rock

Boring for the piles 1000mm dia to the required depth through all types of soil strata including cemented sand, if any up to the founding level and stacking the bored soil at convenient place and transported to location upto a distance not exceeding 1KM as directed by GE and pile shaft cleaning and keeping of all records etc., including bentonite solution, labour, tools, equipment, fuel etc., all as per drawing, specification etc., complete. Note :- 1. If the boring tool encounters rock at an elevation higher than the termination level of the pile indicated in the drawing then the boring shall be continued into the rock from where the boring tool encounters rock first to a depth as directed by Engineer-in-charge. 2. In case the soil stratum at the founding level is loose the Engineer-in-charge may direct the contractor to carryout additional length of boring and payment for such additional work shall also be made under this item. 3. The sample of bored materials at regular interval shall be collected and produced for the verification of the Engineer-in-charge or his representative at no extra cost. In the event of any dispute about the type of strata bored the samples so collected shall be referred to an authorised laboratory / agency report indentified by the Engineer-in-charge and the decision of GE based on such authorised laboratory / agency report is final and binding on both the parties. However the cost of such testing shall be borne by the contractor including transportation of material. (i) Boring through all type of soil strata including cemented sand strata including cemented sand except rubble layer and hard rock

Winch House & STP Pile foundation (From cutoff level to founding level):Positioning and setting upon and/or shifting and setting up piling equipments required for piling work at each piling locations for 800mm dia as shown in the drawing and or as directed including all labour,materials,fuel,tools, equipments etc., complete ( Tripod Method) Boring for the piles to the required depth through all types of soil strata including cemented sand, boulder layers and hard rock if any up to the founding level and stacking the bored soil at convenient place and transported to location as specified herein after as directed by GE and pile shaft cleaning and keeping of all records etc., including bentonite solution, labour, tools, equipment, fuel etc., all as per drawing, specification etc., complete for boring through all type of soil strata including cemented sand strata including cemented sand except rubble layer and hard rock. Notes : 1. If the boring tool encounters rock at an elevation higher than the termination level of the pile indicated in the drawing then the boring shall be continued into the rock from where the boring tool encounters rock first to a depth as directed by Engineer-in-charge. 2. In case the soil stratum at the founding level is loose the Engineer-in-charge may direct the contractor to carryout additional length of boring and payment for such additional work shall also be made under this item. 3. The sample of bored materials at regular interval shall be collect and produce for the verification of the Engineer-in-charge or his representative at no extra cost. In the event of any dispute about the type of strata bored the samples so collected shall be referred to an authorised laboratory / agency report indentified by the Engineer-in-charge and the decision of GE based on such authorised laboratory / agency report is final and binding on both the parties. However the cost of such testing shall be borne by the contractor including transportation of material. 4 The excavated material with all lift and deposited at the location upto a lead of 1000 m as directed by GE

All as per item No. 79 above but for boring through Rock strata using hydraulic pilling rig by diamond cutter etc. with supporting eqipment

Boring through Rock strata using hydraulic pilling rig by diamond cutter etc. with supporting eqipment and removal of excavated materials with all lift and transported and disposed at location upto a distance not exceeding 1KM and as as directed by GE comp for 800mm Dia piles Note :- 1. If the boring tool encounters rock at an elevation higher than the termination level of the pile indicated in the drawing then the boring shall be continued into the rock from where the boring tool encounters rock first to a depth 2. In case the soil stratum at the founding level is loose the Engineer-in-charge may direct the contractor to carryout additional length of boring and payment for such additional work shall also be made under this item. 3. The sample of bored materials at regular interval shall be collected and produced for the verification of the Engineer-in-charge or his representative at no extra cost. In the event of any dispute about the type of strata bored the samples so collected shall be referred to an authorised laboratory / agency report indentified by the Engineer-in-charge and the decision of GE based on such authorised laboratory / agency report is final and binding on both the parties. However the cost of such testing shall be borne by the contractor including transportation of material.

Boring through Rock strata using hydraulic pilling rig by diamond cutter etc. with supporting eqipment and removal of excavated materials with all lift and and transported and disposed at location upto a distance not exceeding 1KM and as as directed by GE comp for 1000mm Dia piles Note :- 1. If the boring tool encounters rock at an elevation higher than the termination level of the pile indicated in the drawing then the boring shall be continued into the rock from where the boring tool encounters rock first to a depth as directed. 2. In case the soil stratum at the founding level is loose the Engineer-in-charge may direct the contractor to carryout additional length of boring and payment for such additional work shall also be made under this item. 3. The sample of bored materials at regular interval shall be collected and produced for the verification of the Engineer-in-charge or his representative at no extra cost. In the event of any dispute about the type of strata bored the samples so collected shall be referred to an authorised laboratory / agency report indentified by the Engineer-in-charge and the decision of GE based on such authorised laboratory / agency report is final and binding on both the parties. However the cost of such testing shall be borne by the contractor including transportation of material.

Chipping of pile heads up to cut-off level as directed and stacking the debris at convenient place and transported outside MD land as specified and directed by the Engineer-in-charge/GE and all associated cleaning of projecting reinforcements including all labour, materials, tools, equipments, fuel etc, complete for 800mm dia plies. Note:- 1.Cutting and removal of liners above pile cut-off level shall be deemed to be included in this item 2. Supply, fabrication of steel reinforcement shall be measured and paid under relevant item. ( Rate shall include the cost of providing additional concrete above the cut-off level) 3. Chipping of pile heads up to cut-off level and /or as directed and stacking the debris at convenient place and transported to low lying ares any where inside the harbour with a lead of 1Km or as directed by the Engineers representative and all associated cleaning of projecting reinforcements including all labour, materials, tools, equipments, fuel etc. complete.

Chipping of pile heads up to cut-off level directed and stacking the debris at convenient place and transported outside MD land as specified and directed by the Engineer-in-charge/GE and all associated cleaning of projecting reinforcements including all labour, materials, tools, equipments, fuel etc, complete 1000 mm dia piles. Note:- Cutting and removal of liners above pile cut-off level shall be deemed to be included in this item.

Driving of sheet pile at site of work, incl cost of equipments, conveyance, erecting and all other incidental charges etc. complete.

Steel formwork to shoe for muff complete lat finished fair and even including all supports from piles in offshore conditions all as specified and directed.

Dismantling of touch piles along with liner and sheet pile to level specified most probably +4.00m to - 7.00 m (11.0m height) under sea water for the at the entrance of sloping track (Final cutoff level to be decided by GE) upto cutoff level including cutting of sheet piles touch pile concrete and reinforcement, removing concrete debris and remains and disposing off all as specified and as directed.

External Electrification : Supply, install, testing and commissioning of aluminium busbar trunking system of 2500 Amps, 1100 volts, AC,50 Hz, 3 phase 4 wire,100% neutral, sandwich insulated type with and including suitable earthing strips running both side, enclosure fabricated out by 1.5 mm (minimum size) hotdip galvanised sheet steel duly painted powder coated, factory fitted, conductors covered by suitable insulators of class "B"complete with and including busbar jumpers, L bend, end feed unit, braided copper flexible jumper, expansion unit, expansion element, standard inspection unit, etc all as per site requirement and holding amply with the mounting system from ceiling/wall including angle iron, anchor fastener etc complete and all as directed by Engr-in-charge.

Supply, installation, testing and commissioning indoor cubical LT feeder Distribution Panel suitable for 3 phase, 4 wire, 415 volts 50 Hz supply system with suitable size and powder coated, dust/vermin proof, totally type tested as per IEC-61439, IP-54 protection, short time with stand capacity of 50KA for 1 second" . The panel shall CPRI approved factory fabricated made with 2 mm thick CRCA sheet for outer shell and inner shell made out of 1.6 mm thick CRCA sheet, double door with front and back openable with locking arrangement, provision of thereaded earthing stud at bottom, inner shell shall be compartmentalized fron openable single door lockable , inner shell shall be completely vermin proof and to accommodate incoming / outgoing ACBs, MCCB, MCBs, and TPN aluminium bus bar and extension links of rating not less than 1.5 times the rated capacity of the respective MCCBs. The TPN busbar and extensions link shall be insulated with colour coated heat shrinkable sleeves and shall be mounted on epoxy resin insulator. The MCCB shall be provided with copper Spreader link of suitable rating. All control wires shall be with 1.5 sqmm multistranded copper conductor wire and shall be properly bunched, tied ferruled for proper identification and crimped with suitable size of lugs. INCOMER - 1 a) ACB 2000 Amps, 4 Pole, 440 V, 50 KA with Electrical draw out type Air Circuit Breaker with Micro Processor trip - release for O/L, S/C, E/F, U/V Protection - 1 Set b) Dual Core Resin Cast CTs of ratio 2000/5A, Class 1.0 the CT burden shall be 15VA - 2 Set (For Metering & APFC) c) Maximum Demand Controller - 1 No d) ACB ON, OFF& TRIP indication lamps - 1 Set e) Control MCB - 1 Set f) Digital Earth Fault Relay - 1 No g) RYB Indicators - 1 Set INCOMER - 2 a) ACB 2000 Amps, 4 Pole, 440 V, 50 KA with Electrical draw out type Air Circuit Breaker with Micro Processor trip - release for O/L, S/C, E/F, U/V Protection - 1 Set b) Dual Core Resin Cast CTs of ratio 16000/5A, Class 1.0 the CT burden shall be 15VA - 1 Set (For Metering) c) Maximum Demand Controller - 1 No d) ACB ON, OFF& TRIP indication lamps - 1 Set e) Control MCB - 1 Set f) Digital Earth Fault Relay - 1 No g) RYB Indicators - 1 Set Interlocking (i) Electrical Interlocking should be done between both incomer to ensure only one incomer is switched on at any given time - 1 Set (ii) Mechanical interlock arrangement for both Incomer by 2Lock by 1Key method - 1 Set Out Going (a) ACB 800 Amps Four Pole Thermal Magnetic Release type Manual Draw out Type - 1 No (APFC Panel) (b) MCCB 630 Amps Four Pole , 50 KA - 2 No (For SSB 1 & 2) (c ) MCCB 400 Amps Four Pole , 36 KA - 3 No (For MPP, MCC PH 1 & MCC PH 2) (d ) MCCB 250 Amps Four Pole , 36 KA - 1 No (Spare) (e ) MCCB 200 Amps Four Pole , 25 KA - 1 No (Spare) (f ) MCCB 160 Amps Four Pole , 25 KA - 2 No (For MLP & Spare)

Supply, installation, testing and commissioning indoor cubical LT 425 KVAR capacitor panel with MDXL type capacitors suitable for 3 phase, 4 wire, 415 volts 50 Hz supply system with suitable size and powder coated, 'with seven tank processfrom inside and out side duly prewired with suitable size FRLS PVC insulated multistranded copper conductor wire for capacitor stages, metering & control accessories, earthing strips for connecting earth strips, cable entry from bottom". The panel shall CPRI approved factory fabricated made with 2 mm thick CRCA sheet for outer shell and inner shell made out of 1.6 mm thick CRCA sheet, double door with front and back openable with locking arrangement, provision of thereaded earthing stud at bottom, inner shell shall be compartmentalized fron openable single door lockable , inner shell shall be completely vermin proof and to accommodate incoming / outgoing ACBs, MCCB, MCBs, Contactors, Capacitor bank and TPN aluminium bus bar and extension links of rating not less than 1.5 times the rated capacity of the respective MCCBs. The TPN busbar and extensions link shall be insulated with colour coated heat shrinkable sleeves and shall be mounted on epoxy resin insulator. The MCCB shall be provided with copper Spreader link of suitable rating. All control wires shall be with 1.5 sqmm multistranded copper conductor wire and shall be properly bunched, tied ferruled for proper identification and crimped with suitable size of lugs. (a) ACB 800 Amps Four Pole Thermal Magnetic Release type Manual Draw out Type - 1 No (Incomer) (b) APFC 12 stage relay including auto manual switch, CT control fuses - 1 Set (c ) 100 KVAR Capacitor with MCCB 250A TP 35KA & TP capacitor duty contactor - 2 Set (d ) 50 KVAR Capacitor with MCCB 125 A TP 25 KA & TP capacitor duty contactor - 3 Set (e ) 25 KVAR Capacitor with MCCB 63 A TP 25 KA & TP capacitor duty contactor - 1 Set (f ) 15 KVAR Capacitor with MCCB 40 A TP 25 KA & TP capacitor duty contactor - 2 Set (g ) 10 KVAR Capacitor with MCB 40 A TP 10 KA & TP capacitor duty contactor - 1 Set

(h ) 05 KVAR Capacitor with MCB 25 A TP 10 KA & TP capacitor duty contactor - 1 Set (j ) 2.5 KVAR Capacitor with MCB 16 A TP 10 KA & TP capacitor duty contactor - 2 Set (k) Capacitor On off indication lamps for all banks - 1 Set (l) R Y B Indication lamps - 1 Set m) Space heater, 60 Watt, 230 volts Ac alongwith toggle switch -1 set. n) Ventilation fans of 6" sweep size alongwith filter and thermostat switch, to dissipiate the heat liberated by capacitor units complete with automatic switching ON and OFF of fan depending upon the temperature of the panel, suitable for 230 volts, 50 Hz, AC -1 No.

Supply, installation, testing and commissioning indoor cubical LT Panel suitable for 3 phase, 4 wire, 415 volts 50 Hz supply system with suitable size and powder coated, dust/vermin proof. The panel shall CPRI approved factory fabricated made with 2 mm thick CRCA sheet for outer shell and inner shell made out of 1.6 mm thick CRCA sheet, double door with front and back openable with locking arrangement, provision of thereaded earthing stud at bottom, inner shell shall be compartmentalized fron openable single door lockable , inner shell shall be completely vermin proof and to accommodate incoming / outgoing ACBs, MCCB, MCBs, Contactors, Capacitor bank and TPN aluminium bus bar and extension links of rating not less than 1.5 times the rated capacity of the respective MCCBs. The TPN busbar and extensions link shall be insulated with colour coated heat shrinkable sleeves and shall be mounted on epoxy resin insulator. The MCCB shall be provided with copper Spreader link of suitable rating. All control wires shall be with 1.5 sqmm multistrandad copper conductor wire and shall be properly bunched, tied ferruled for proper identification and crimped with suitable size of lugs. (a) MCCB 4 Pole 160 Amp 50 Hz 415 V 36 KA-01 No (Incoming) (b) MCB 3 Pole 40 Amp 50 Hz 415 V 10 KA-06 No (For High bay lighting LDB - 1, 2 & 3 -3 Nos, High Mast Light DB - 1No, Dry Berth Area 1 & 2 Inside LDB - 1No, Spare - 1No) (c) MCB 3 Pole 32 Amp 50 Hz 415 Volts 10 KA-06 Nos (For LDB - 4, 5 & 6 - 3Nos, lighting DB and Spare - 2 Nos) (d) R Y B panel Indicators - 1 Set (g) Digital Multi Function Meter -1 No

Supply, installation, testing and commissioning indoor cubical LT feeder Distribution Panel suitable for 3 phase, 4 wire, 415 volts 50 Hz supply system with suitable size and powder coated, dust/vermin proof. The panel shall CPRI approved factory fabricated made with 2 mm thick CRCA sheet for outer shell and inner shell made out of 1.6 mm thick CRCA sheet, double door with front and back openable with locking arrangement, provision of thereaded earthing stud at bottom, inner shell shall be compartmentalized fron openable single door lockable , inner shell shall be completely vermin proof and to accommodate incoming / outgoing ACBs, MCCB, MCBs, and TPN aluminium bus bar and extension links of rating not less than 1.5 times the rated capacity of the respective MCCBs. The TPN busbar and extensions link shall be insulated with colour coated heat shrinkable sleeves and shall be mounted on epoxy resin insulator. The MCCB shall be provided with copper Spreader link of suitable rating. All control wires shall be with 1.5 sqmm multistranded copper conductor wire and shall be properly bunched, tied ferruled for proper identification and crimped with suitable size of lugs. (a) MCCB 4 Pole 400 Amp 50 Hz 415 V with rupturing capacity 36 KA-01 No(Incoming) (b) MCCB 3 Pole 160 Amp 50 Hz 415 V with rupturing capacity 25 KA-01 No(Spare) (c) MCCB 3 Pole 125 Amp 50 Hz 415 V with rupturing capacity 25 KA-04 Nos ((For PDB - 4,5 & 6 and Spare) (d) MCCB 3 Pole 100 Amp 50 Hz 415 V with rupturing capacity 25 KA-01 Nos (Spare) (e) MCCB 3 Pole 63 Amp 50 Hz 415 V with rupturing capacity 25 KA -01 Nos (Spare) (f) R Y B panel Indicators - 1 Set (g) Digital Multi Function Meter -1 No

Supply, installation, testing and commissioning indoor cubical LT feeder Distribution Panel suitable for 3 phase, 4 wire, 415 volts 50 Hz supply system with suitable size and powder coated, dust/vermin proof. The panel shall CPRI approved factory fabricated made with 2 mm thick CRCA sheet for outer shell and inner shell made out of 1.6 mm thick CRCA sheet, double door with front and back openable with locking arrangement, provision of thereaded earthing stud at bottom, inner shell shall be compartmentalized fron openable single door lockable , inner shell shall be completely vermin proof and to accommodate incoming / outgoing ACBs, MCCB, MCBs, and TPN aluminium bus bar and extension links of rating not less than 1.5 times the rated capacity of the respective MCCBs. The TPN busbar and extensions link shall be insulated with colour coated heat shrinkable sleeves and shall be mounted on epoxy resin insulator. The MCCB shall be provided with copper Spreader link of suitable rating. All control wires shall be with 1.5 sqmm multistranded copper conductor wire and shall be properly bunched, tied ferruled for proper identification and crimped with suitable size of lugs. (SSB Panel 1 - Dispersal Area & Transfer ARea Load) (a) MCCB 630 Amps Four Pole , 50 KA - 1 No (b) MCCB 160 Amps TP, 36 KA - 6 No (For Dry Berth - 1,2 & 3 Ship Load - 3 Nos, Sloping Track & Transfer bay winch house motor - 2Nos, Spare - 1No) (c ) MCCB 63 Amps TP Pole , 25 KA - 4 No (Dry Berth Industrial Power Socket 1,2,3 & Gantry crane in Dry Berth) (d ) MCCB 32 Amps TP Pole , 25 KA - 4 No (Dry Berth Power Socket 1,2,3 & Spare) (e) Digital Multi Function Meter - 1 No (f) CT 630/5 Amps - 1 Set (g) RYB panel Indicators - 1 Set

Supply, installation, testing and commissioning indoor cubical LT feeder Distribution Panel suitable for 3 phase, 4 wire, 415 volts 50 Hz supply system with suitable size and powder coated, dust/vermin proof. The panel shall CPRI approved factory fabricated made with 2 mm thick CRCA sheet for outer shell and inner shell made out of 1.6 mm thick CRCA sheet, double door with front and back openable with locking arrangement, provision of thereaded earthing stud at bottom, inner shell shall be compartmentalized fron openable single door lockable , inner shell shall be completely vermin proof and to accommodate incoming / outgoing ACBs, MCCB, MCBs, and TPN aluminium bus bar and extension links of rating not less than 1.5 times the rated capacity of the respective MCCBs. The TPN busbar and extensions link shall be insulated with colour coated heat shrinkable sleeves and shall be mounted on epoxy resin insulator. The MCCB shall be provided with copper Spreader link of suitable rating. All control wires shall be with 1.5 sqmm multistranded copper conductor wire and shall be properly bunched, tied ferruled for proper identification and crimped with suitable size of lugs. (SSB Panel 2 - Slip Way Bldg Machines) (a) MCCB 630 Amps Four Pole , 50 KA - 1 No (b) MCCB 160 Amps TP , 36 KA - 3 No (For PDB 1 & 2 & Spare - 1No) (c ) MCCB 100 Amps TP Pole , 25 KA - 2 No (For PDB -3 & Spare - 1 No) (d ) MCCB 63 Amps TP Pole , 25 KA - 2 No (Spare 2 No) (e) Digital Multi Function Meter - 1 No (f) CT 630/5 Amps - 1 Set (g) RYB panel Indicators - 1 Set

Supply & laying GI cable tray perforated type of 2.0mm thick, including clamping / fastening the cable by means of necessary binding material such as binding wires, nuts, bolts, clamps, MS powder coated brackets of suitable size at interval of 750 mm complete for holding cable all as specified and directed by Engineer in charge, of following sizes (a) 450 X 75 X 2.0 mm

(b) All as per item No 96 above but for 300 x 75 x 2.0mm

(c) All as per item No 96 above but for 150 x 50 x 2.0mm

(d) All as per item No 96 above but for 50 x 50 x 2.0mm

Supply & laying GI cable tray perforated type of 1.6 mm thick, including clamping / fastening the cable by means of necessary binding material such as binding wires, nuts, bolts, clamps, MS powder coated brackets of suitable size at interval of 750 mm complete for holding cable all as specified and directed by Engineer in charge, of following sizes (a) 450 x 50 x 1.6mm

(b) All as per item No 100 above but for 300 x 50 x 1.6mm

(c) All as per item No 100 above but for 150 x 50 x 1.6mm

(d) All as per item No 100 above but for 50 x 50 x 1.6mm

Supply and lay cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with copper conductor including connecting to the panel board with suitable size of copper gland, connecting acessaries such as nuts, bolt, washer etc complete all as specified and directed by Engineer in charge, of sizes 4 core 2.5 sqmm.

Supply and lay cable PVC Insulated PVC round sheathed , electric power cables 1100 Volts grade confirming to IS 694 with flexible copper conductor including connecting to the panel board with suitable size of copper gland, connecting acessaries such as nuts, bolt, washer etc complete all as specified and directed by Engineer in charge, of following sizes. (a) 4C X 2.5 Sqmm copper flexible cable

(b) All as per item No 106 above but for 3Core X 2.5 Sqmm copper flexible cable

(c) All as per item No 106 above but for 4Core X 95 Sqmm copper flexible cable

(d) All as per item No 106 above but for 3Core X 95 Sqmm copper flexible cable

Supply and fix in 60 Watts LED street light fittings in street light poles complete with and including drivers, pressure die cast aluminium housing, prewired complete. the fitting shall be of Crompton Cat no LSTP-60CDL or Equivalent from Philips/Bajaj

M&L for Multistandarded Copper Conductor cable of 3 Core 1.5 Sq mm size drawn through poles for interconnection of connector terminal & light fitting etc

Note contd.. :- c) The cost of foundation bolts along with nuts, washers,anchor plate,template,and foundation (as per manufacturer design) is deemed to be included in the unit rate qouted and nothing extra shall be paid to contractor in this regard

Supply and install fire point fabricated out of 16 gauge metal; sheet and MS pipe of suitable size, masonry platforms with associated civil work, duly painted withfire red, inscribe "FIRE" in white letters on both sides of roof etc as approved by Fire authority with the following equipments:- a) Fire bucket made out of 24 gauge galvanised iron, painted outside with fire red paint and black on bottom and inscribe with "FIRE"- 4nos. b) Fire extinguisher CO2 type 4.5 Kg capacity as per IS-15683 c) Ceiling hook as per IS-926 d) Fire beater e) Shovel f) Fire gong

Supply & erection of Shock Treatment chart in Hindi & English languages duly laminated/ glass framed of approx size 600x600 mm fixed to wall complete all as directed by Engr-in-Charge

Supplying and laying synthetic Rubber insulated mats 2.5 mm thick for voltage upto 11 kv for electrical purpose as per IS 15652-2006, (superseding IS 5424) suitable for electrical shock safety of sizes 2m x 1m.

Suply & erection of fire extingusher Co2 type 4.5 KG confirm to TAC norms.

Supply of Earth Discharge Rod length of 5 mtr, and 12 mm dia with necessary insulated hand grip all as specified and directed by Engineer in charge.

Supply of Hand gloves suitable to work on 11KV equipments with ISI mark

Supply & erection of First aid box containing full compliment of medicines, ointments & bandages etc.,

Supply , erect and fixing pre-cast RCC pole , M-30 design mix 11 m long of corss section 380mm x 250mm at bottom and 150x125mm at top including reinforcement with high strength deformed steel TMT bars and necessary form work and erecting in position all as specified /shown on drawing and as directed Notes : (a) The rate quoted deemed to include the following provision also : - i) Excavation in any type of soil, returning, filling and removal of surplus soil to a distance of 50m ii) Foundation in PCC (1:4:8) type D2 using 40mm graded stone aggregate iii) Coping in PCC (1:3:6) type C1 using 20mm grated stone aggregate

S & F drop out fuse unit with insulators of 11000 volts grade

Supply, installation, testing and commissioning out door cubical LT Panel suitable for 3 phase, 4 wire, 415 volts 50 Hz supply system with suitable size and powder coated, dust/vermin proof. The panel shall CPRI approved factory fabricated made with 3 mm thick CRCA sheet for outer shell and inner shell made out of 1.6 mm thick CRCA sheet, double door with front and back openable with locking arrangement, provision of thereaded earthing stud at bottom, inner shell shall be compartmentalized fron openable single door lockable , inner shell shall be completely vermin proof and to accommodate incoming / outgoing MCCB, MCBs, energy meter and TPN aluminium bus bar and extension links of rating not less than 1.5 times the rated capacity of the respective MCCBs. The TPN busbar and extensions link shall be insulated with colour coated heat shrinkable sleeves and shall be mounted on epoxy resin insulator. The MCCB shall be provided with copper Spreader link of suitable rating. All control wires shall be with 1.5 sqmm multistranded copper conductor wire and shall be properly bunched, tied ferruled for proper identification and crimped with suitable size of lugs. (For shore supply at support jetty of sloping track) (a) MCCB 4 Pole 250 Amp 50 Hz 415 V 36 KA-01 No (Incoming) (b) MCCB 4 Pole 200 Amps, 50 HZ 440 Volt 36 kA - 1 No (Shore Supply at Support Jetty) (c) MCCB 4 Pole 63 Amp 50 Hz 440 V -1 No (Shore Supply at Support Jetty) (d) Three Phase 4 Wire Tri Vector Meter Class 0.5 Bs BM, including CT of Rating 200/5 Amps - 2 No

External Fire Fighting :Supply and fix foam and water monitor 75 mm dia self educting type with swivel joint for horizontal & vertical rotation, nozzle, Lock handles, base flange, drain valves including water/foam threaded barrel, foam induction body, foam pick up tube, strainer, foam nozzle attachement and including 200 ltrs AFFF foam 3 % concenctrated stored in suitable storage tank provided with threaded foam inlet, foam outlet, foam drain valves and connecting with monitor, testing complete all as specified and directed

Supply and fix bronze Air release Valves with single air Outlets, conforming to IS 14845 of size 25 mm dia bore and fixing up in MS ERW Water supply mains.

Supply & lay 1.5 Sqmm 4 core armoured copper conductor cable, the cable shall be properly saddled in wall, floor along with saddles and clamps (For Connecting Pressure switch with Starter Panel)

Supply, installation, testing and commissioning indoor cubical LT feeder Distribution Panel suitable for 3 phase, 4 wire, 415 volts 50 Hz supply system with suitable size and powder coated, dust/vermin proof. The panel shall CPRI approved factory fabricated made with 2 mm thick CRCA sheet for outer shell and inner shell made out of 1.6 mm thick CRCA sheet, double door with front and back openable with locking arrangement, provision of thereaded earthing stud at bottom, inner shell shall be compartmentalized fron openable single door lockable , inner shell shall be completely vermin proof and to accommodate incoming / outgoing ACBs, MCCB, MCBs, and TPN aluminium bus bar and extension links of rating not less than 1.5 times the rated capacity of the respective MCCBs. The TPN busbar and extensions link shall be insulated with colour coated heat shrinkable sleeves and shall be mounted on epoxy resin insulator. The MCCB shall be provided with copper Spreader link of suitable rating. All control wires shall be with 1.5 sqmm multistranded copper conductor wire and shall be properly bunched, tied ferruled for proper identification and crimped with suitable size of lugs. (a) MCCB 4 Pole 200 Amp 50 Hz 415 V, 36 KA-01 No(Incoming) (b) MCCB 3 Pole 160 Amp 50 Hz 415 V, 25 KA-01 No (c) Star Delta Starter 70 HP 3pase 440 volts - 1 Set (d) MCCB 3 Pole 63 Amp 50 Hz 415 V, 25 KA-01 No (e) Star Delta Starter 20 HP 3pase 440 volts - 1 Set (f) R Y B panel Indicators - 1 Set (g) Digital Multi Function Meter -1 No (h) Starter system for Diesel engine driven Pump Set - 1 Set (j) The panel shall be provisioned with automatic & manual mode operation of pumps - 1 Set k) MCCB 3 pole 32 Amps 415 V 25 KA- 3 nos.( 1 No for domestic pumps, 1 no for STP and 1 no spare)

supply and fix Canvas fire hose of dia 63 mm and length 30 meter of perccolating type conforming to IS, with proper exterior and interior coatings and with both end coupling conforming to IS 903 and including binding of end coupling with copper wire complete all as specified and directed. (For Ground Hydrants)

Supply, installation, testing and commissioning indoor cubical LT feeder Distribution Panel suitable for 3 phase, 4 wire, 415 volts 50 Hz supply system with suitable size and powder coated, dust/vermin proof. The panel shall CPRI approved factory fabricated made with 2 mm thick CRCA sheet for outer shell and inner shell made out of 1.6 mm thick CRCA sheet, double door with front and back openable with locking arrangement, provision of thereaded earthing stud at bottom, inner shell shall be compartmentalized fron openable single door lockable , inner shell shall be completely vermin proof and to accommodate incoming / outgoing ACBs, MCCB, MCBs, and TPN aluminium bus bar and extension links of rating not less than 1.5 times the rated capacity of the respective MCCBs. The TPN busbar and extensions link shall be insulated with colour coated heat shrinkable sleeves and shall be mounted on epoxy resin insulator. The MCCB shall be provided with copper Spreader link of suitable rating. All control wires shall be with 1.5 sqmm multistranded copper conductor wire and shall be properly bunched, tied ferruled for proper identification and crimped with suitable size of lugs. (a) MCCB 4 Pole 315 Amp 50 Hz 415 V , 36 KA-01 No(Incoming) (b) MCCB 3 Pole 250 Amp 50 Hz 415 V, 25 KA-01 No (c) Star Delta Starter 160 HP 3pase 440 volts - 1 Set (d) MCCB 3 Pole 63 Amp 50 Hz 415 V, 25 KA-01 No (e) Star Delta Starter 25 HP 3pase 440 volts - 1 Set (f) R Y B panel Indicators - 1 Set (g) Digital Multi Function Meter -1 No (h) Starter system for Diesel engine driven Pump Set - 1 Set (j) The panel shall be provisioned with automatic & manual mode operation of pumps - 1 Set

FIRE ALARM SYSTEM : Supply & lay FRLS 4 core 1.5 sqmm (red Colour) armoured multi stranded copper conductor heavy duty cable saddled in wall/ceiling, truss etc all as specified and directed by engineer-in-charge

Sypply and fix electric motor siren conforming to IS 1941 suitable for 3 phase 415 Volts supply with motor not exeeding 3.75 KW and able to deliver 143 DB level. Siren shall have automatic equipment for producing a warbling note and including starter unit, relay module, foundation etc complete all as specified and directed.

GANTRY CRANE : Design, fabrication, Supply, install, testing, commissioning of electrically operated 20 Ton capacity outdoor type Gantry Crane operating on 415 Volts 50 HZ power supply, including lower leg, upper led, CT Girder, CT rail trolley, motors, gear box, control panels, etc the crane shall confirm to the following specification and accessories, (i) Capacity – 20 Ton(ii) CT Span – 12 Meters(iii) Class of duty M – 5 (iv) Design Standard – IS 3177 (1999) & IS 807 (2006)(v) Hook Height – 25 Meters from FFL (vi) Hoist Speed – 3 Meters per Min(vii) Cross Travel Speed – 15 Meters/Min(viii) Long Travel Speed – 20 Meters/Min (ix) Motorised cable reeling drum with cable(x) Hoist Motor(xi) Long Travel Motor (xii) Cross Travel Motor(xiii) VVVF Drive control panel with overload relays and motor protection circuits siutable for dual speed of operation (Micro speed and main speed). (xiv) Limit Switches with Wiring(xv) Gear box, Wire rope, pulley, Hoist hook, (xvi) EHT type brake for hoist, brake for cross travel & long travel shall be fail to safe EM disc type inbuilt in gear brake motor. (xvii) Pre fabricated/steel construction Canopy for trolley, hoist mechanism, cross travel mechanism, long travel mechanism, LT panels, (xviii) Safety covers/guard for all rotating parts. (xix) Method of Operation - The Crane shall be operated through RRC (Push Button type) pendant from floor level and from cabin with provision for two speed micro and main speed. xx) Load Indicator - LED display of 100 mm font size load indicator with Load pin type load cells with provision for indication of load, alarm if the crane exceeds 95 % of rated load and shut down of crane in case of load greater than 25 % of rated load. (xxi) Audio & Visual Indicators - Siren with audio and visual facility shall be provided to provide indications while crane is in operation. (xxii) Anti Collision Device – Infra Red type anti collision device shall be provided (xxiii) Platform/Walk Way – Full length platform/walk way on both side of the CT girder. (xxiv) Lightening arrester – 2 Nos rod type to be provided (xxv) Emergency push button to be provisioned in cabin. (xxvi) Encoder for hoisting motor for deducting of fault and feedback. Note : (i) Factory inspection on crane components shall be carried out by Rep of Accepting officer, for this the contractor shall give one month prior notice to GE for consideration by accepting officer and detailing of Rep.(ii) The contractor is responsible for taking correct measurements of gantry rails layout as executed at site before taking up procurement action and placing order on the manufacturer.(iii) Cost of long travel gantry ISCR rail including foundation/fixing arrangements of Gantry Rail on deck with all acessories is deemed to be inclusive in the rate quoted for this item.

Supply & fix LT Panel 3 Phase 440 volts, out door type, made out of CRCA sheet of 3 mm thick for outer shell and 1.6 mm thick for inner shell, the panel shall comprise of MCCB 4 pole 100 Amps 25 KA with extension links for incoming & out going cables, with gland plate, etc and all as directed by Engr-in-charge.

E/M EQUIPMENT FOR WINCH: Design, supply, install, testing and comissioning of Electric Power Driven Double drum Winch Machine Equipment, both parallel and independent operation for hauling up & down, Capacity 70 MT, with safety Factor 1.25, the Winch shall be designed in accordance with the latest editions of IS-9507.1979, with latest Amendments alongwith adequate size rope (both dia & length), winding capacity of drum for the rope, sufficent number of rope Layers, wire rope clamps, alloy steel eye hook, U-clamp, D-clamps etc complete, area of operation all as per drg No. CE/WD/2021 sht no. 2/32,3/32 and 4/32. Rope Drum Fabricated with Mild Steel Seamless Pipe, Drum as per IS: 226 Duly Machined of adequate thickness with Flanges at both ends. Winding capacity upto designed length of Wire Rope. Variable Speed (Mtr/Min) 5 to 20 Mtr/Min. Electro Hydraulic Type Brake of reputed make, M S Bearing Block with self alligned Spherical Roller Bearing, suitable capacity Motors, TEFC, 40% CDF, 150 Starts per Hr., A.C., S4 Crane Duty,Sq. Cage Induction Motor, Operation Through floor Pendent Push Button etc complete and mounted on winch platform, Dust and Vermin Proof Steel Sheet Box Housing having Main Line Contactors, Power Supply 415V +/- 10%, 3 Phase A.C, 50 Hz. Helical / Worm type, Multi Stage Reduction, Machine cut Gears, Splash Lubricated with reduction on output side of Gearbox to achieve desired speed and torque, and driving pinion duly covered with safety cover to avoid any inappropriate circumstances. Designed and tested at 125% Safe working load. Winch shall be tested for satisfactory performances after installation at site, and mounted on ISMC Channel Frame with other fabricated plates for mounting Rope drum , Motor, Electro Hydraulic Type Brake, Gearbox - Helical / Worm type, Multi Stage Reduction, Machine cut Gears, Splash Lubricated, Electrical Panel Board with adequate rating switch gears, VVVF drives, controls, indicators and measuring instruments, mannual/remote control etc. Lifting lugs and foundation mounts for easy winch mounting on floor and easy handling during transportation. Duly painted with one coat of Zinc Chromate Primer followed by anti corrosive paint and two Coat of synthetic enamel paint of smoke grey colour enamel Paint, etc all as directed.

Note: i) The contractor shall submit the detailed drawing, design, specifications, foundation detail, dimensioned layout plan, manufacturers specification, brouchers, accessories and make of winch duly vetted by IITM and submitted for the approval of accepting officer with in 90 days from date of commencement of work. (ii) The cost of foundation and ancilliaries are deemed to included in the unit rate quoted. (iii) Design & provision of Steel wire rope of suitable length for hauling operations for berthing of ships in Dry berth and vice versa shall also be included in the design of winch and the rates shall be inclusive of the same. (iv) Arrangements for connecting the ropes to the cradles for smooth operation shall also be properly designed and provided. Rate quoted for the item shall be inclusive of the above.

Supply, install & testing of high bay light fitting of 170 watts, LED type, including suitable brackets for mounting in steel truss, with 1.5 sqmm 3 core wire from ceiling rose to light fitting. The fitting shall confirm to Cat NO - BY515PLED250S 57NB PSU GR of philips or its equipment in Bajaj/Havels/Luker (For Dry Berth)

Material & Labour for Supply, fabricate, fixing and testing of 1000 mm dia MS Pulley suitable for 70 TON designed winch operations capacity including fixing to RCC deck slab using anchor bolts, base plates etc complete all as shown on drawings and as directed. Note :- (i) The cost of ancilliaries such as base plates , anchor bolts etc. are deemed to included in the unit rate quoted. (ii) The location of pulley shown in drawing is tentative. (iii) The anchorr bolts shall be embedded in the concrete while casting the deck slab.

SEWAGE TREATMENT PLANT : Design, Supply, Installation, tesing & comissioning of package type sewage treatment plant based on principle of aerobic attached moving Bed Bio-reactor (MBBR) including all necessary Electro Mechanical and all civil worksfor STP capacity 10 KLD as per OEM specification to achieve the parameters mentioned. including additional 2 Nos Raw sewage transfer pump having discharge 0.5 m3/Hr, head 10 Meter for pumping of raw sewage from deck to STP with protection shed, starter and all acessories. The sewage parameters shall be as under, Parameters Inlet Oulet pH - 6.5 to 8.5 6.5 to 8.5 TSS - 300 to 350 PPM <10 PPM BOD - 200 to 350 PPM <10 PPM COD - 400 to 500 PPM <100 PPM O & G - 30 PPM <10 PPM Note :- (i) The technical specification mentioned are tentative and for guidance only. The responsiblity lies with the bidder so as to ensure output criteria and quality of treated sewer. (ii) The description is brief Any detail, equiment, acessories in addition to that described in BOQ/PS, but are essential to achieve critical specification for treated water/effulent, shall be provided by contractor and rate quoted is deemed to be inclusive of such additional/missing details.

Diesel Generator Supply, install, testing and commissioning of approved OEM factory assembled diesel generator set of totally enclosed and sound proof (with acoustic enclosure) of capacity 625 KVA, 3 phase, 4 wire, 415 volts, 1500 RPM, AC power supply with power factor 0.8, coupled directly to alternator mounted on common base plate complete with fuel tank, battery and standard accessories and fittings, vibration pads, PCC foundation complete all as specified and directed. The genset shall conform to CPCB norms for noise and emission limits and including the following : (a) Alternator :- Standard design alternator rated at 625 KVA net output at site after considering all derating factors, site conditions and at power factor 0.8, AC 3 phase, 4 wire 415 volts, 50 cycles, 1500 RPM, self excited, self regulated, screen protected, drip proof IP-23 enclosure, brushless design, insulating class H, voltage regulation +/- 1% operated voltage from no load to full load and shall be in position to generate supply with frequency regulation within +/- 3% tolerance, revolving field type, including cable terminal box with insulator & bus bar cor connecting 04 nos of aluminum 3.5 coe 300 Sqmm cable. (b) DIESEL ENGINE: Adequate capacity diesel engine suitable to above alternator, radiator water cooled, to drive independently above alternator and after considering derating as per site conditions directly coupled to alternator multicylinder, multistroke, direct injection, cold starting, 1500 RPM, with an overload cap of 10% for 1 hour in any 12 hours continuous running complete with standard accessories all as specified and required for safe running and operation with accessories shall be as under:- (i) Flywheel (ii)Air cleaner wet/dry type (iii) fuel Filter (iv) Fuel Injection system incl. injection pump, solenoid switch, nozzle as per manufacturer's specifications (v) Lubricating oil filter (vi) Lubricating oil pump (vii) Turbocharger (viii) Radiator (ix) 24 volts starting system consisting of batteries of capacity as recommended by manufacture+r, battery connections with copper leads and with lugs of adequate size, initial charging of batteries, battery charger/ generator with regulator, starter motor, starter gear (x) Exhaust silencer complete with exhaust pipe of suitable dia. (xi) Microprocessor control electronic metering and module for indication of battery voltage, oil pressure, engine RPM, hour

Supply, installation, testing and commissioning PLC based synchronizing cum AMF panel indoor type suitable for 3 phase, 4 wire, 415 volts 50 Hz supply system of suitable size and powder coated, dust/vermin proof. The panel shall be CPRI approved factory fabricated made with 2 mm thick CRCA sheet for outer shell and inner shell made out of 1.6 mm thick CRCA sheet, double door with front and back openable with locking arrangement, provision of threaded earthing stud at bottom, inner shell shall be compartmentalized front openable single door lockable , inner shell shall be completely vermin proof and to accommodate incoming / outgoing ACBs, MCBs, and TPN aluminium bus bar and extension links of rating not less than 1.5 times the rated capacity of the respective ACBs, MCCBs. The TPN busbar and extensions link shall be insulated with colour coated heat shrinkable sleeves and shall be mounted on epoxy resin insulator. The ACB shall be provided with copper extension link of suitable rating for connecting cable. All control wires shall be with 1.5 sqmm multistranded copper conductor wire and shall be properly bunched, tied ferruled for proper identification and crimped with suitable size of lugs. (a) INCOMER ACB 1250 Amps, 4 Pole, 440 V, 50 KA with Electrical draw out type Air Circuit Breaker with Micro Processor trip - release for O/L, S/C, E/F, U/V Protection - 2 Set (for DG 1 & DG 2) (b) Out Going a) ACB 2000 Amps, 4 Pole, 440 V, 50 KA with Electrical draw out type Air Circuit Breaker with Micro Processor trip - release for O/L, S/C, E/F, U/V Protection - 1 Set c) Dual Core Resin Cast CTs of ratio 1250/5A, Class 1.0 the CT burden shall be 15VA - 2 Set d) Dual Core Resin Cast CTs of ratio 2000/5A, Class 1.0 the CT burden shall be 15VA - 2 Set (Metering & Control) e) Maximum Demand Controller - 2 No f) ACB ON, OFF& TRIP indication lamps - 2 Set g) Control MCB - 2 Set h) Digital Earth Fault Relay - 2 No j) RYB Indicators - 3 Set (Incomer – 1, Incomer – 2, Out Going) h) Tri vector energy meter along with CT - 3 Set

j) PLC based Syncro controller with AMF control, Auto Synchronizing & auto load sharing with circuit - 1 Set k) Synchroscope, with circuit - 1 Set l) Dark Lamp/Bright lamp Indicators - 1 Set m) Annunciation lamps - 1 Set n) Manual Start/ Stop facility to operate DG sets in parallel mode & in mono mode along with circuit, controller & wiring, manual start stop push buttons - 1 Set o) Indicators with warning signal for water temperature, engine temperature, fuel level etc p) Digital multi function meter – 3 Set (Incomer 1, Incomer 2, & Out Going) q) Emergency push button with circuit – 2 Set r) Control wiring between panel & DG Set – 1 Set

Supply & Fix HDGI Octagonal pole 7 Meter height having top dia 70 mm and bottom dia 135 mm and thickness 3 mm, including heavy duty GI single arm bracket with nuts & bolts, 4 Nos 'J' type foundation bolts of dia 16 mm and 450 mm long with base plate and including Excavation in post holes not exceeding 0.5 Cum for erection of poles, removing the excavated materials to distance not exceeding 50 meter and providing PCC bed and RCC foundation as per following including form work (i) PCC BED - 450 mm X 450 mm X 100 mm (ii) RCC Column - 400 mm X 400 mm X 1300 mm, M20 Design, using 4 Nos 12 mm Steel Bar

Supply & Laying of GI strip of size 50 mm X 6 mm as earth continuity conductor along with welding, nuts & bolts for connection to be laid inside cable service trench, cable tray, through pipe etc

Providing services for Manning, Running & daily operation of Sub station (HT/LT) located at 3 Lane Slip Way, by deploying One Electrician Skilled in each shift (Three shift per day - 8 Hours per shift), including Sundays & Holidays and also attending break downs/ repairs on break down, and rectify the problems by replacing minor spares and restore the electric supply in area with necessary arrangement etc consisting of following :- (a) VCB 11 KV - 1 Nos (b) 1250 KVA Dry Type Transformer with Lt panels - 1 No, (c) DG Set 625 KVA with Synchronization palel - 2 No Note :- (a) Cost including the rate of theminor spares as required, Safety devices and apron shall be provided by the contractor and will be continuously in use by the operator on the duty. No extra payment shall be made for the same (b) SHIFT DUTIES (TIMINGS) (i) First Shift : 0600 Hours to 1400 Hours (ii) Second Shift : 1400 Hours to 2200 Hours (iii) Third Shift : 2200 Hrs to 0600 Hrs (c) All tradesman being deployed by the contractor for rendering manning & operation services for E/M installation should posses adequate and minimum educational qualification and experience which render them suitable for the job as approved by GE. (d) Attendance register and nominal roll of tradesman deployed must be meticulously maintained. (e) All tradesman deployed by the contractor should not wear loose clothes while operating plant and machinery. Proper clothing (preferably a overall combination) with name plate and required protective gears (like Helmets, Hand gloves, goggles, rubber boots etc wherever necessitated ) will be made available by the contractor. (f) Rate to be quoted for per month

Providing services for Manning, Running & daily operation of Sub station (HT/LT) located at 3 Lane Slip Way, by deploying One helper in each shift (Three shift per day - 8 Hours per shift), including Sundays & Holidays and also attending break downs/ repairs on break down, and rectify the problems by replacing minor spares and restore the electric supply in area with necessary arrangement etc consisting of following :- (a) VCB 11 KV - 1 Nos (b) 1250 KVA Dry Type Transformer with Lt panels - 1 No, (c) DG Set 625 KVA with Synchronization palel - 2 No Note :- (a) Cost including the rate of theminor spares as required, Safety devices and apron shall be provided by the contractor and will be continuously in use by the operator on the duty. No extra payment shall be made for the same (b) SHIFT DUTIES (TIMINGS) (i) First Shift : 0600 Hours to 1400 Hours (ii) Second Shift : 1400 Hours to 2200 Hours (iii) Third Shift : 2200 Hrs to 0600 Hrs (c) All tradesman being deployed by the contractor for rendering manning & operation services for E/M installation should posses adequate and minimum educational qualification and experience which render them suitable for the job as approved by GE. (d) Attendance register and nominal roll of tradesman deployed must be meticulously maintained. (e) All tradesman deployed by the contractor should not wear loose clothes while operating plant and machinery. Proper clothing (preferably a overall combination) with name plate and required protective gears (like Helmets, Hand gloves, goggles, rubber boots etc wherever necessitated ) will be made available by the contractor. (f) Rate to be quoted for per month

Providing services for Manning, Running & daily operation of STP of 10 KLD capacity, domestic Pumps, Fire fighting pumps located at 3 Lane Slip Way, by deploying One FGM Skilled in one shift per day, including Sundays & Holidays and also attending break downs/ repairs on break down, and rectify the problems by replacing minor spares and restore the electric supply in area with necessary arrangement etc consisting of following :- (a) Package type STP 10 KLD Capacity - 1 No (b) Domestic Pump Set - 2 Nos (b) Diesel Engine Driven Fire pump set - 2No, (c) Electric Driven Fire pump set - 2 No (d) Jockey pump - 2 No Note :- (a) Cost including the rate of the minor spares as required, Safety devices and apron shall be provided by the contractor and will be continuously in use by the operator on the duty. No extra payment shall be made for the same (b) SHIFT DUTIES (TIMINGS) - Asper directions of Garrison Engineer (c) All tradesman being deployed by the contractor for rendering manning & operation services for E/M installation should posses adequate and minimum educational qualification and experience which render them suitable for the job as approved by GE. (d) Attendance register and nominal roll of tradesman deployed must be meticulously maintained. (e) All tradesman deployed by the contractor should not wear loose clothes while operating plant and machinery. Proper clothing (preferably a overall combination) with name plate and required protective gears (like Helmets, Hand gloves, goggles, rubber boots etc wherever necessitated ) will be made available by the contractor. (f) Rate to be quoted for per month

ITD CEMENTATION INDIA LIMITED

AFCONS INFRASTRUCTURE LIMITED