Package No.562_1

1. CIVIL WORK : Earth work in excavation by mechanical means (Hydraulic excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50m. 2.8.1 All kinds of soil

Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12mm mud mortar, including filling joints with Jamuna sand, with common burnt clay non modular bricks. A) Brick on flat soling

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering-All work up to plinth level : 4.1.5 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources).

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. 5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level. 5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more

Centering and shuttering including strutting, propping etc. and removal of form for : 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete.

Centering and shuttering including strutting, propping etc. and removal of form for : 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts.

Centering and shuttering including strutting, propping etc. and removal of form for : 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Centering and shuttering including strutting, propping etc. and removal of form for: 5.9.3 Suspended floors, roofs, landings, balconies and access platform.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement-All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement: 1.5 coarse sand (zone -III) derived from natural sources: 3 graded stone aggregate 20mm nominal size derived from natural sources).

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: 6.1.2 cement mortar 1:6 (1 cement: 6 coarse sand).

Half brick masonry with common burnt clay F.P.S (non modular) bricks of class designation 7.5 in foundation and plinth in. 6.12.2 Cement mortar 1:4 (1 cement: 4 coarse sand).

12mm cement plaster of mix : 13.1.1 /1:4 (1 cement: 4 fine sand)

15mm cement plaster on the rough side of single or half brick wall of mix: (13.2.1/1:4 (1 cement: 4 fine sand).

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). 9.1.1 Second class teak wood.

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required sized with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:-Butt hinges and necessary screws shall be paid separately). 9.5.1 Second class teak wood 9.5.1.1 35mm thick shutters

Providing and laying vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved make, in all colours and shade, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. complete Tile 800x800mm

Excavating supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20cm in trenches, plinth, sides of foundation etc. complete.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shade except burgundy, bottle green, black of any size as approved by Engineer-in-charge, in skirting, risers of steps and dados, over 12mm thick bed of cement mortar 1:3 (1 cement:3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigments of matching shade complete.

62mm thick cement concrete flooring with concrete hardener topping, under layer 50mm thick cement concrete 1:2:4 (1 cement: 2 coarse sand :4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc.complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade: 13.41.1 New work (two or more coats) over and including water thinnable priming coat with cement primer.

INTERIOR FINISHING Finishing walls with water proofing cement paint of required shade: 13.44.1 New work (Two or more coats applied @ 3.84 kg/10 sqm).

INTERIOR FINISHING Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface: 13.43.1 Water thinnable cement prime

Providing and fixing M.S. grills of required pattern in frames of windwos etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. 9.48.1 Fixed to steel windows by welding.

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 9.74.1 250x10mm

Providing and fixing bright finished brass door latch with necessary screws etc. complete : 9.75.1 300x16x5mm

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade, with necessary screws etc. complete: 9.100.1 125mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade, with necessary screws etc. complete: 9.97.2 250x10mm

Providing and laying integral cement based treatment for water proofing on horizontal surface at all depth below ground level for under ground structures as directed by Engineer-in-charge and consisting of grading roof for water proofing treatment with cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size.

Float glass panes 4mm thick glass pane (weight not less than)

30 mm thick factory made PVC door shutters made of stylesand rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt decorative moulding edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x30 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter).

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement:3 coarse sand (zone-III) : 6 graded stone aggregate 20mm nominal size) over 75mm thick bed of dry brick ballast 40mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc. including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

2. SEPTIC TANK : Earth work in excavation by mechanical means (Hydraulic excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50m. 2.8.1 All kinds of soil.

Dry brick pitching half brick thick in drains including supply of bricks and preparing the surface complete: 16.12.1 With common burnt clay clay F.P.S. (non modular) bricks of class designation 7.5

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering-All work up to plinth level : 4.1.5 1:3:6 (1 Cement: 3 coarse sand (zone-III) derived from natural sources: 6 graded stone aggregate 20mm nominal size derived from natural sources).

Steel reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Centering and shuttering including strutting, propping etc. and removal of form for : 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete.

Centering and shuttering including strutting, propping etc. and removal of form for : 5.9.3

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement-All work up to plinth level : 5.1.3 1:2:4 (1 cement: 2 coarse sand (zone-III) derived from natural sources :4 graded stone aggregate 20mm nominal size derived from natural sources).

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: 6.1.2 cement mortar 1:4 (1 cement: 4 coarse sand).

15mm cement plaster on the rough side of single or half brick wall of mix: 13.2.1 1:3 (1 cement: 4 fine sand).

Cement plaster skirting with cement mortar (1:3).

Square shade 450x450mm precast RCC manhole cover with frame-L.D.-2.5

Constructing soak pit 1.20x1.20x1.20m filled with brick bats including S.W. drain pipe 100mm diameter and 1.20m long complete as per standard design.

3. ELECTRIFICATION (INTERNAL + EXTERNAL) Wiring for light point/fan point/exhaust fan point/call bell point with 1.5sq.mm FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. 1.10.2 Group-B

Supplying and fixing following piano type socket on the existing switch box/cover including connections etc. as required. 1.23.4 3 pin 5/6A socket outlet

1.23.5 6 pin 15/16 A socket outlet

Wiring for circuit/submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required. 1.14.1 2x1.5sq.mm + 1 x 1.5 sq.mm earth wire

1.14.2 2x2.5sq.mm + 1 x 2.5 sq.mm earth wire

1.14.3 2x4sq.mm + 1 x 4 sq.mm earth wire

1.14.4 2x6sq.mm + 1 x 6 sq.mm earth wire

1.14.9 4x6sq.mm + 2 x 6 sq.mm earth wire

1.14.10 4x10sq.mm + 2 x 6 sq.mm earth wire

Providing and fixing following capacity TP&N disconnector fuse switch unit inside the existing panel board with ISI marked HRC fuses including drilling holes in cubical panel. 2.1.4 125A TP&N

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator). 2.3.2 8 way, Double door

2.3.3 12 way, Double door

Supplying and fixing 5A to 32A rating, 240/415V, 10KA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 2.5.1 4 way (4+12) double door

Supplying and fixing 5A to 32 A rating, 240/415 V, 10 KA, "C' curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 2.10.1 single pole

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 m A in the existing MCB DB complete with connections, testing and commissioning etc. as required. 2.14.2 40A

Supply, Installation, Testing and Commissioning of 1200mm sweep, BEE 5 star rated, ceiling fan with brush less Direct Current (BLDC) Motor, class of …….insulation resistance more than 2 mega ohm, suitable for 230V, 50Hz, single phase AC supply, earthing etc. complete as required.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing call bell/buzzer suitable for single phase, 230 V, complete as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/coke and salt as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/recessed conduit/submain wiring/cable as required.

Earthing with copper earth plate 600mm x 600mm x 3mm thick including aceessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/coke and salt) as required.

Supplying and laying 25mm x 5mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut.

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. 7.1.1 Upto 35sq.mm

Supplying fitting & fixing of LED tube light aluminium extruded smart bright batten light fitting (4ft) model No.BN021C LED22S PSU CW GR (Philips make) as required and as directed by the department.

Supplying fitting & fixing of LED Bulb (7W/9W/12W) non-dimmable in the existing batten/angle holder as required and as directed by the Department (Philips or eqvt. Make).

Supplying installaton testing and commissioning of Green Perform lighet luminaries of model no. 5116877-12701385672 (Philps make as required and as directed by the Deptt. Basic price for Green Perform Sleek LED down ligter luminaries of model NO5116877-12701385672 (Philips make) including GST (1200 lumen).

Supplying, fitting & fixing of exhaust fan 230mm sweep model No.Ventil Air-DS (Havells make) as required and as directed by the Department.

Supplying including installation, testing and commissioning of Hi-Wall Non ductable type of 1.50 Ton capacity having proper cooling capacity single phase 3 STAR MODEL Split type inverter Air Conditioner Machine complete with corded remote, copper pipe connection between indoor & outdoor unit, electrical connection etc. (Voltas Make) Model No.Voltas SAC 183V CZR 2 Ton Capacity

Supplying with fitting and fixing of 4 KVA Voltage stabilizer including making necessary connection as approved, specified and directed by the deptt. (Vee-Dee make) Model No.VD 40908

Supplying with fitting and fixing of Single Phase Modular Motor Starter switch including making necessary connection as per direction of

Supplying Installation testing and commissioning of pressure dia cast powder coated aluminium alloy housing forested PC diffuser IP65/IP66 protection of street light including connection with 2.5sq.mm 3 core PVC insulated rounded copper conductor Model No.(ENDURA CITYLINER NEO 70W) (Havells make) as required and as directed by the Deptt.

Supplying, fitting & fixing of LED Decorative post TOP lantern with IP65 protection (Baja) make fitted on existing GI pipe with all accessories as required and as directed by the Department.

Supplying including installation, commissioning of vermin and dust proof totally enclosed, Phosphatised Powder Painted cubical outdoor type double door, floor mounting compartmentalize panel board of size 800mm x 1200mm x 400mm made of 16 SWG1.66m thick C.R. sheet and 35mm x 35mm x 5mm size angle having 4 no legs at the bottom and C.R. sheet roofing on the top. The panel board is to be erected in 1:3:6 PCC of foundation including excavation of trench and brick soling etc. complete neatly wiring done with provision for 1) 1 No 250A 4 pole 415V MCCB 2) 2 Nos.250A SPREADER TERMINAL, 3) 1 No 160 A 4p MCCB 4) 2 Nos.160A SREADER TERMINAL 5) 3 Nos 32A 4P MCB etc.

Supplying with fitting and fixing of 4 pole 100A 415V Front handle operator Onload Changeover switch (IP-20 protection powder painted sheet steel enclosure fitted on angle Iron frame of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. (Havells/Hager/Legrand or equivalent make).

Supply of following size PVC/XLPE insulated and PVC sheathed 1.1 KVG Solid Aluminium conductor upto 10sq.mm balance stranded conductor, XLPE insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core upto 70sq.mm balance Aluminium strip, Galvanised for cables upto 2x10sq. mm 3x10 sq mm balance all galvanised steel strip), extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908 (Part 1) 1988 armoured U.G. cable laid in ground/partially in air (as required for termination up as specified and directed by the Deptt. (RR Kable/Havells/Polycab make or equivalent). 6.00 sq.mm 2 core armoured cable (Havells or equivalent make).

35sq.mm armoured cable 3.5 core (Havells or equivalent make).

Supplying including installation connection as approved by the Deptt. Testing and commissioning of JET MONOBLOCK PUMP SET complete as directed and specified by the Deptt. 1 HP Single phase jet monoblock twp stage pump set (Texmo/Crompton Greaves/Aquatic/CRI/V Guard make) 2900 rpm with DOL Starter (Crompton Greaves/Control & Switch Gear/BCH/L&T/Siemens make). Internal Electrical

Supplying and erection PSC Pole 8.5 metre long, the pole is to be erection in 1:2:3 plain cement concrete foundation f size 1.50m x 0.45m x 0.45m having PCC base foundation 15cm x 60cm x 60cm including edge brick soiling and plastering above G.L. portion (0.30 metre complete with excavation of earth, handling of surplus soil, debris etc. to the proper place and refilling etc. as specified and as directed by the Department. (APDCL Approved Rate).

Supplying and fixing of LT stay set as required and as directed by the Department.

Supplying and laying of following size 1.1 KV (LT) Grade (Insulated massanger cum neutral) ABC 3C x 120 sq.mm + 1C x 95 sq.mm (Massenger cum neutral)+1Cx25 sq.mm for street lighting including fitting required size of lugs at the both end of the cable by using crimping tool and making good damaged done as specified and directed by the Department. (APDCL Approved Rate).

Supplying and fitting fixing of GI Angle (50x50x6mm) as required and as directed by the department. (APDCL Approved Rate).

Supplying and erection of L.T. Shackle Insulator Porcelain with shackle strap complete with blots and nuts coach screw etc. as required and as directed by the department. (APDCL Approved Rate).

Extension of payment to be made to the APDCL authority for load Security Load as per APDCL norms. (Considering 1KW Load).

Payment to be made APDCL authority for 3 phase 4 wire ICS DLMS complaint HT Trivector energy meter as specified and directed by the Department.

Supervision Charge for LT Line as per APDCL Requirement.

5. WATER SUPPLY WORKS (INTERNAL AND EXTERNAL) : Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat & lit, 10 low level white PVC flushing cistern manually controlled device (handle liver), conforming to IS:7231, with all fittings and fixtures complete including cutting & making good the walls and floors wherever required. 17.2.1 WC Pan with ISI marked white plastic seat and lid.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required. 17.7.1. White vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing & fixing PVC waste pipe for sink or wash basin including PVC waste fittings complete. 17.28.1 Semi rigid pipe 17.28.1.1 32mm dia

Providing & fixing 100mm sand cast iron grating for gully trap

Providing and fixing 600 x 450mm bevelled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with CP brass screws and washers complete.

Providing and fixing toilet paper holder 17.34.1 C.P. Brass

Providing and fixing PTMT Bottle Trap for wash basin and sink 17.70.1 Bottle trap 31mm single piece moulded with height of 270mm, effective length of tail pipe 260mm from the centre of the waste coupling, 77mm breadth with 25mm minimum water seal, weighing not less than 260gms

Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fitting of approved quality colour and make, weighing not less than 105 gms.

Providing and fixing PTMT towel ring trapezoidal shade 215mm long, 200mm wide with minimum distances of 37mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

B) C.P.V. Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings this includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer-in-charge. 18.9.8 80mm nominal dia pipes

18.9.9 100mm nominal dia pipes

C) WATE SCHE Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as pe direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the walls etc. 18.8.1 15mm nominal dia pipes

18.8.2 20mm nominal dia pipes

Providing and fixing GI pipes complete with GI fitting and clamps, including cutting and making good the walls etc. (Internal work). 18.10.1 Exposed on wall: (Internal work). 18.10.1 15mm nominal bore

18.10.3 25mm nominal bore

18.10.5 40mm dia nominal bore

External Work: Providing and fixing gun metal gate valve with CI wheel of approved quality (screwed end). 18.17.1 25mm nominal bore

18.17.3 40mm nominal bore

Providing and fixing ball valve (brass) of approved quality. High or low pressure with plastic floats complete. 18.18.3 a) 25mm nominal bore

Providing and fixing gun metal non-return valve of approved quality (screwed end). 18.19.4 50mm nominal bore 18.19.2.3 Horizontal

Providing & fixing C.P. brass shower rose with 15 or 20mm inlet: 18.22.1 100mm diameter.

Providing & fitting sand of grading zone V or coarser grade alround the GI pipes in external work: 18.41.6 50mm diameter pipe

Providing & fixing CP brass bib cock of approved quality conforming IS: 8931: 18.49.1 15mm nominal bore

Providing and fixing CP brass stop cock (concealed) of standard design and approved make confirming to IS:8931. 18.52.1 15mm nominal bore

Providing and fixing CP brass angle valve for basin mixer and gyser points of approved quality confirming IS:8931: 18.53.1 15mm nominal bore

Providing and placing on terrace (at all floor levels) polythene water storage tank of approved brand and manufacture with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

6. PLANTATION : Digging holes in ordinary soil and refilling the same with the excavated earth mixed 2.14 with manure or sludge in the ratio of 21 by volume (2 parts of stacked volume of earth after reduction by 20% I part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth it any with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately). 2.14.1 Holes 12m dis and 1.2m deep.

Hall brick circular tree guard in bricks internal diameter 1.25 metre and height 12 metre 215 above ground and 0.20m below ground, bottom tow courses laid dry and top three courses in cement mortar 18 (1 cement fine sand) and the intermediate courses being in dry honey comb masonry as per design complete 2151 with common burnt clay FPS (non modular) bricks of class designation 50.

Providing and stacking of Azadirachta indica Neem) of height 120-130cm in big polybag of size 25cm as per direction of the officer in charge.

Providing and stacking of Bauhinia blakcana (Kachnar) of height 120 150cm in big poly bags of size 25cm as per direction of the officer in charge.

Providing and stacking of Delonix regia (Gulmohar) of height 150-165 cm in big poly 7.24 hugs of size 25cm as per direction of the officer in charge.

Providing and stacking of Palyalthus longifolia (Ashok) of height 150-165cm in earthen 7.74 pots of size 25cm as per direction of the officer in charge.

Please Enable Macros to View BoQ information