Police station

EARTH WORK EXCAVATION FOR FOUNDATIONS AND DEPOSITING ON BANK, FOR ALL LIFTS AND WITH AN INITIAL LEAD OF 10M INCLUDING ALL INCIDENTAL, OPERATIONAL, LABOUR CHARGES SUCH AS SHORING, SHEETING, PLANKING, STRUTTING, DEWATERING SITE CLEARANCE, CLEARING SHURBS, BRUSHWOOD, UNDER GROWTH AND SMALL TREES NOT EXCEEDING 300 MM GIRTH, MEASURED AT ONE METRE ABOVE GROUND ETC., BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK INCLUDING DEWATERING CHARGES ETC AS PER SS - 20 B FOR STIFF BLOCK COTTON SOIL , HARD RED EARTH, MURRAM, ORDINARY GRAVEL - MANUAL MEANS UP TO 3M DEPTH - FOUNDATION OF BUILDING (APSS 308).

CEMENT CONCRETE (1:4:8) PROP. USING 40MM HARD GRANITE MACHINE CRUSHED METAL WITH MACHINE MIXING UP TO PLINTH LEVEL INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LAYING, CURING, FINISHING, ALL OTHER INCIDENTAL, OPERATIONAL, LABOUR ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE FOR FINISHED ITEM OF WORK. FOUNDATIONS & UNDER STONE SLAB FLOORING .(APSS NO: 402).

RE-FILLING WITH USEFUL AVAILABLE EXCAVATED EARTH OTHER THAN EXPANSIVE SOILS LIKE RED EARTH AND ORDINARY GRAVEL ETC., (EXCLUDING ROCK) IN TRENCHES, SIDES OF FOUNDATIONS AND BASEMENT WITH INITIAL LEAD IN LAYERS NOT EXCEEDING 15 CM THICK, CONSOLIDATING EACH DEPOSITED LAYER BY WATERING AND RAMMING INCLUDING COST AND CONVEYANCE OF WATER TO WORK SITE AND ALL INCIDENTAL, OPERATIONAL, LABOUR CHARGES , HIRE CHARGES OF T & P ETC., BUT EXCLUDING GST - COMPLETE FOR FINISHED ITEM OF WORK. (APSS NO. 309 & 310)

FILLING WITH CARTED GRAVEL IN TRENCHES, SIDES OF FOUNDATIONS AND BASEMENT WITH INITIAL LEAD IN LAYERS NOT EXCEEDING 15 CM THICK, CONSOLIDATING EACH DEPOSITED LAYER BY WATERING AND RAMMING INCLUDING COST AND CONVEYANCE OF WATER TO WORK SITE AND ALL INCIDENTAL, OPERATIONAL, LABOUR CHARGES, HIRE CHARGES OF T & P ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST, COMPLETE FOR FINISHED ITEM OF WORK. (APSS NO. 309 & 310)

RANDAM RUBBLE MASONRY USING HARD GRANITE STONE IN CM(1:6) PROP. INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, SEIGNORAGE CHARGES,LABOUR CHARGES, CURING, ETC., COMPLETE FOR FOUNDATIONS AND BASEMENTS FOR FINISHED ITEM OF WORK. APSS NO: 615).

SUPPLY AND PLACING OF THE DESIGN MIX CONCRETE OF M25 CORRESPONDING TO IS 456 USING WEIGH BATCHER WITH 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND - 0.40 CUM) COARSE AGGREGATE (0.80 CUM), WATER ETC., TO SITE , INCLUDING ALL OPERATIONAL, INCIDENTAL AND LABOUR CHARGES SUCH AS WEIGH BATCHING, MACHINE MIXING, LAYING CONCRETE, CURING ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS. COMPLETE WITH MINIMUM CEMENT CONTENT OF 380 KGS PER CUM OF CONCRETE, INCLUDING PROVIDING CENTERING USING CASURINA BALLIES, BAMBOOS, WOODEN REAPERS, RUNNERS, WOOD POSTS, WALL PLATES, STEEL CENTERING PLATES ETC., FOR UNSUPPORTED HEIGHT 3.66M , VIBRATING, CURING, LIFTING(MANUAL) ETC COMPLETE BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK FOR FOOTINGS(APSS NO.403)

SUPPLY AND PLACING OF THE DESIGN MIX CONCRETE OF M25 CORRESPONDING TO IS 456 USING WEIGH BATCHER WITH 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND - 0.40 CUM) COARSE AGGREGATE (0.80 CUM), WATER ETC., TO SITE , INCLUDING ALL OPERATIONAL, INCIDENTAL AND LABOUR CHARGES SUCH AS WEIGH BATCHING, MACHINE MIXING, LAYING CONCRETE, CURING ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS. COMPLETE WITH MINIMUM CEMENT CONTENT OF 380 KGS PER CUM OF CONCRETE, INCLUDING PROVIDING CENTERING USING CASURINA BALLIES, BAMBOOS, WOODEN REAPERS, RUNNERS, WOOD POSTS, WALL PLATES, STEEL CENTERING PLATES ETC., FOR UNSUPPORTED HEIGHT 3.66M , VIBRATING, CURING, LIFTING(MANUAL) ETC COMPLETE BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK FOR PEDESTALS(APSS NO.403)

SUPPLY AND PLACING OF THE DESIGN MIX CONCRETE OF M25 CORRESPONDING TO IS 456 USING WEIGH BATCHER WITH 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND - 0.40 CUM) COARSE AGGREGATE (0.80 CUM), WATER ETC., TO SITE , INCLUDING ALL OPERATIONAL, INCIDENTAL AND LABOUR CHARGES SUCH AS WEIGH BATCHING, MACHINE MIXING, LAYING CONCRETE, CURING ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS. COMPLETE WITH MINIMUM CEMENT CONTENT OF 380 KGS PER CUM OF CONCRETE, INCLUDING PROVIDING CENTERING USING CASURINA BALLIES, BAMBOOS, WOODEN REAPERS, RUNNERS, WOOD POSTS, WALL PLATES, STEEL CENTERING PLATES ETC., FOR UNSUPPORTED HEIGHT 3.66M , VIBRATING, CURING, LIFTING(MANUAL) ETC COMPLETE BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK FOR PLINTH BEAMS(APSS NO.403)

SUPPLY AND PLACING OF THE DESIGN MIX CONCRETE OF M25 CORRESPONDING TO IS 456 USING WEIGH BATCHER WITH 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND - 0.40 CUM) COARSE AGGREGATE (0.80 CUM), WATER ETC., TO SITE , INCLUDING ALL OPERATIONAL, INCIDENTAL AND LABOUR CHARGES SUCH AS WEIGH BATCHING, MACHINE MIXING, LAYING CONCRETE, CURING ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS. COMPLETE WITH MINIMUM CEMENT CONTENT OF 380 KGS PER CUM OF CONCRETE, INCLUDING PROVIDING CENTERING USING CASURINA BALLIES, BAMBOOS, WOODEN REAPERS, RUNNERS, WOOD POSTS, WALL PLATES, STEEL CENTERING PLATES ETC., FOR UNSUPPORTED HEIGHT 3.66M , VIBRATING, CURING, LIFTING(MANUAL) ETC COMPLETE BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK FOR GROUND FLOOR COLUMNS (APSS NO.403)

PLAIN CEMENT CONCRETE (1:3:6) PROP. USING 20MM GRADED HARD GRANITE MACHINE CRUSHED METAL INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, CENTERING, MACHINE MIXING, LAYING, CURING, FINISHING, ALL OTHER INCIDENTAL, OPERATIONAL, LABOUR CHARGES ETC.,BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE FOR FINISHED ITEM OF WORK. BED BLOCKS IN GROUND FLOOR (APSS NO: 402).

SUPPLY AND PLACING OF THE DESIGN MIX CONCRETE OF M25 CORRESPONDING TO IS 456 USING WEIGH BATCHER WITH 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND - 0.40 CUM) COARSE AGGREGATE (0.80 CUM), WATER ETC., TO SITE , INCLUDING ALL OPERATIONAL, INCIDENTAL AND LABOUR CHARGES SUCH AS WEIGH BATCHING, MACHINE MIXING, LAYING CONCRETE, CURING ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS. COMPLETE WITH MINIMUM CEMENT CONTENT OF 380 KGS PER CUM OF CONCRETE, INCLUDING PROVIDING CENTERING USING CASURINA BALLIES, BAMBOOS, WOODEN REAPERS, RUNNERS, WOOD POSTS, WALL PLATES, STEEL CENTERING PLATES ETC., FOR UNSUPPORTED HEIGHT 3.66M , VIBRATING, CURING, LIFTING(MANUAL) ETC COMPLETE BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK FOR BEAMS GROUND FLOOR (APSS NO.403)

SUPPLY AND PLACING OF THE DESIGN MIX CONCRETE OF M25 CORRESPONDING TO IS 456 USING WEIGH BATCHER WITH 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND - 0.40 CUM) COARSE AGGREGATE (0.80 CUM), WATER ETC., TO SITE , INCLUDING ALL OPERATIONAL, INCIDENTAL AND LABOUR CHARGES SUCH AS WEIGH BATCHING, MACHINE MIXING, LAYING CONCRETE, CURING ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS. COMPLETE WITH MINIMUM CEMENT CONTENT OF 380 KGS PER CUM OF CONCRETE, INCLUDING PROVIDING CENTERING USING CASURINA BALLIES, BAMBOOS, WOODEN REAPERS, RUNNERS, WOOD POSTS, WALL PLATES, STEEL CENTERING PLATES ETC., FOR UNSUPPORTED HEIGHT 3.66M , VIBRATING, CURING, LIFTING(MANUAL) ETC COMPLETE BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK FOR GROUND FLOOR SLABS 125MM THICK (APSS NO.403)

SUPPLY AND PLACING OF THE DESIGN MIX CONCRETE OF M25 CORRESPONDING TO IS 456 USING WEIGH BATCHER WITH 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND - 0.40 CUM) COARSE AGGREGATE (0.80 CUM), WATER ETC., TO SITE , INCLUDING ALL OPERATIONAL, INCIDENTAL AND LABOUR CHARGES SUCH AS WEIGH BATCHING, MACHINE MIXING, LAYING CONCRETE, CURING ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS. COMPLETE WITH MINIMUM CEMENT CONTENT OF 380 KGS PER CUM OF CONCRETE, INCLUDING PROVIDING CENTERING USING CASURINA BALLIES, BAMBOOS, WOODEN REAPERS, RUNNERS, WOOD POSTS, WALL PLATES, STEEL CENTERING PLATES ETC., FOR UNSUPPORTED HEIGHT 3.66M , VIBRATING, CURING, LIFTING(MANUAL) ETC COMPLETE BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK FOR GROUND FLOOR SLABS OF 150MM THICK (APSS NO.403)

MASONRY WORK IN CM (1:6) PROP WITH FLYASH CEMENT SOLID BLOCKS OF SIZE 290 X 225 X 140 MM FOR MANUFACTURING OF FLYASH SOLID BLOCKS USING FLYASH OF 80 KGS, CEMENT OF 15 KGS. GYPSUM OF 5 KGS. AND STONE DUST INCLUDING COST AND CONVEYANCE OF ALL MATERIALS, LABOUR CHARGES, SCAFFOLDING AND CURING ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE WITH A COMPRESIVE STRENGTH NOT LESSTHAN 50 KG/SQM FOR SUPERSTRUCTURE WALLS OF 225MM THICK GROUND FLOOR FOR FINISHED ITEM OF WORK(APSS NO. 501&504)

MASONRY WORK IN CM (1:4) PROP WITH FLYASH CEMENT SOLID BLOCKS OF SIZE 290 X 100 X 140 MM FOR MANUFACTURING OF FLYASH SOLID BLOCKS USING FLYASH OF 80 KGS, CEMENT OF 15 KGS. GYPSUM OF 5 KGS. AND STONE DUST INCLUDING COST AND CONVEYANCE OF ALL MATERIALS, LABOUR CHARGES, SCAFFOLDING AND CURING ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE WITH A COMPRESIVE STRENGTH NOT LESSTHAN 50 KG/SQM FOR SUPERSTRUCTURE WALLS OF 100MM THICK GROUND FLOOR. FOR FINISHED ITEM OF WORK(APSS NO. 501&504)

RCC M - 20 NOMINAL MIX (Cement:fine aggregate: coarse aggregate) CORRESPONDING TO TABLE 9 OF IS 456 USING 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND), COARSE AGGREGATE, WATER ETC., TO SITE AND INCLUDING ALL OPERATIONAL, INCIDENTAL AND LABOUR CHARGES SUCH AS MACHINE MIXING, LIFTING ( MANNUAL), LAYING CONCRETE, CURING ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE AND PROVIDING CENTERING USING CASURINA BALLIES, BAMBOOS, WOODEN REAPERS, RUNNERS, WOOD POSTS, WALL PLATES, STEEL CENTERING PLATES ETC., FOR UNSUPPORTED HIEGHT OF 3.66M BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK (APSS NO.403) FOR GROUND FLOOR LINTELS

RCC M-20 NOMINAL MIX (CEMENT : FINE AGGREGATE : COARSE AGGREGATE) CORRESPONDING TO TABLE 9 OF IS 456 USING 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND) , COARSE AGGREGATE, WATER ETC., ALL INCIDENTAL, OPERATIONAL AND LABOUR CHARGES SUCH AS MACHINE MIXING, LIFTING (MANUAL), LAYING CONCRETE, CURING ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE AND PROVIDING CENTERING USING CASURINA BALLIES, BAMBOOS, WOODEN REAPERS, RUNNERS, WOOD POSTS, WALL PLATES, STEEL CENTERING PLATES ETC., FOR UNSUPPORTED HIEGHT OF 3.66M BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK - FOR SUNSHADES OF 50MM AVERAGE THICK INCLUDING DRIP COURSE OF SIZE 40MM WIDE X 20MM HEIGHT IN CEMENT MORTAR (1:4)PROP FOR GROUND FLOOR (APSS NO. 403)

RCC M - 20 NOMINAL MIX (Cement:fine aggregate: coarse aggregate) CORRESPONDING TO TABLE 9 OF IS 456 USING 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND), COARSE AGGREGATE, WATER ETC., TO SITE AND INCLUDING ALL OPERATIONAL, INCIDENTAL AND LABOUR CHARGES SUCH AS MACHINE MIXING, LIFTING ( MANNUAL), LAYING CONCRETE, CURING ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE AND PROVIDING CENTERING USING CASURINA BALLIES, BAMBOOS, WOODEN REAPERS, RUNNERS, WOOD POSTS, WALL PLATES, STEEL CENTERING PLATES ETC., FOR UNSUPPORTED HEIGHT OF 3.66M BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK (APSS NO.403) FOR GROUND FLOOR RACKS 25MM

PLASTERING TO SUPERSTRUCTURE 20 MM THICK IN TWO COATS, WITH A BASE COAT OF 16 MM THICK IN CM (1:6) PROP. AND TOP COAT OF 4 MM THICK IN CM (1:4) PROP. with sponze finishing, INCLUDING MAKING GROOVES, COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES, SCAFFOLDING, LIFTING ( MANUAL) CURING, ALL OTHER INCIDENTAL AND OPERATIONAL CHARGES ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE FOR FINISHED ITEM OF WORK. FOR FOR BASEMENT (APSS NO: 901&904)

PLASTERING TO SUPERSTRUCTURE 20 MM THICK IN TWO COATS, WITH A BASE COAT OF 16 MM THICK IN CM (1:6) PROP. AND TOP COAT OF 4 MM THICK IN CM (1:4) PROP. with sponze finishing, INCLUDING MAKING GROOVES, COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES, SCAFFOLDING, LIFTING ( MANUAL) CURING, ALL OTHER INCIDENTAL AND OPERATIONAL CHARGES ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE FOR FINISHED ITEM OF WORK. FOR GROUND FLOOR (APSS NO: 901&904)

PLASTERING TO SUPERSTRUCTURE 12 MM THICK IN TWO COATS, WITH A BASE COAT OF 8 MM THICK IN CM (1:6) PROP. AND TOP COAT OF 4 MM THICK IN CM (1:4) PROP. with sponze finishing, INCLUDING MAKING GROOVES, COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES, SCAFFOLDING, LIFTING ( MANUAL) CURING, ALL OTHER INCIDENTAL AND OPERATIONAL CHARGES ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE.FOR FINISHED ITEM OF WORK. GROUND FLOOR (APSS NO: 901&904)

ORNAMENTAL PLASTERING 12MM THICK WITH A BASE COAT OF 8 MM THICK IN CM (1:5) PROP. AND FINISH COAT OF 4MM THICK IN CM (1:3) PROP. WITH DUBARA SPONGE FINISHING COMPLETE INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES, SCAFFOLDING, LIFTING (MANNUAL), CURING, ALL OTHER INCIDENTAL AND OPERATIONAL CHARGES ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE. FOR FINISHED ITEM OF WORK (APSS NO: 901 & 904) GROUND FLOOR

FLOORING WITH DOUBLE CHARGED / MULTI CHARGED STAIN FREE FULL BODY PORCELAIN VITRIFIED TILES WITH DOUBLE LAYER PIGMENT OF SIZE 600 X 600 MM AND THICKNESS BETWEEN 8-10 MM 1ST QUALITY CONFORMING TO 3711, IS:13712, IS:13630 (PARTS 1 TO 15) OF ANY COLOUR AND FINISH IN ALL SHADES AND DESIGNS, SET OVER BASE COAT OF CEMENT MORTAR (1:8), 12 MM THICK OVER CC BED ALREADY LAID OR RCC ROOF SLAB, INCLUDING NEAT CEMENT SLURRY OF HONEY LIKE CONSISTENCY SPREAD @ 3.3.KGS PER SQM & JOINTED NEATLY WITH WHITE CEMENT PASTE TO FULL DEPTH MIXED WITH PIGMENT OF MATCHING SHADE, INCLUDING COST OF ALL MATERIALS LIKE CEMENT, SAND WATER AND TILES ETC., COMPLETE, INCLUDING LIFTING (MANUAL) AND ALL LABOUR CHARGES, ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE FOR FINISHED ITEM OF WORK. FOR GROUND FLOOR

PROVIDING SKIRTING TO INTERNAL WALLS TO 15 CM HEIGHT/RISERS OF STEPS WITH DOUBLE CHARGED / MULTI CHARGED STAIN FREE FULL BODY PORCELAIN VITRIFIED TILES WITH DOUBLE LAYER PIGMENT OF SIZE 600 X 600 MM AND THICKNESS BETWEEN 8-10 MM 1ST QUALITY CONFORMING TO 13711, IS:13712, IS:13630 (PARTS 1 TO 15) OF ANY COLOUR AND FINISH IN ALL SHADES AND DESIGNS, SET OVER BASE COAT OF CM (1:5) 12 MM THICK WITH CEMENT SLURRY OF HONEY LIKE CONSISTENCY SPREAD AT THE RATE OF 3.30 KGS PER SQM AND JOINTED WITH WHITE CEMENT PASTE MIXED WITH PIGMENT OF MATCHING SHADE TO FULL DEPTH, INCLUDING COST OF ALL MATERIALS LIKE TILES, CEMENT, SAND AND WATER ETC., COMPLETE INCLUDING LIFTING (MANUAL) AND ALL LABOUR CHARGES, ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE FOR FINISHED ITEM OF WORK. FOR GROUND FLOOR

DADOOING WITH DIGITAL / POLISHED GLAZED FULL BODY PORCELAIN WALL TILES OF SIZE 300 X 600 MM WITH ANY TYPE OF DESIGN TEXTURE SUCH AS MARBLE FINISH, WOODEN, BAMBOO, STONE FINISHES ETC., SCRATCH LESS, STAIN FREE AND THICKNESS BETWEEN 6-8 MM 1ST QUALITY CONFORMING TO IS:13711, IS:13712, IS:13630 (PARTS 1 TO 15) OF ANY COLOUR AND FINISH IN ALL SHADES AND DESIGNS AS APPROVED BY EXECUTIVE ENGINEER, SET OVER 12MM THICK CM (1:3) BASE COAT AND NEAT GREY CEMENT SLURRY OF HONEY LIKE CONSISTENCY AT THE RATE OF 3.3 KGS PER SQ.MT AND JOINTED WITH 2 KGS WHITE CEMENT PASTE MIXED WITH PIGMENT OF MATCHING SHADE TO MATCH THE SHADE OF TILES INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LIFTING (MANNUAL), ALL INCIDENTAL, OPERATIONAL, LABOUR CHARGES SUCH AS MIXING MORTAR, FIXING TILES IN POSITION, INCLUDING LIFT CHARGES, CURING, CUTTING THE BRICK MASONARY WALLS AND REDOING THE SAME SUCH THAT THE TOP SURFACE OF TILES IS TO BE FLUSHED WITH PLASTERED SURFACE ETC., INCLUDING ALL LABOUR CHARGES, BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE FOR FINISHED ITEM OF WORK. FOR GROUND FLOOR.

FLOORING WITH HIGH POLISHED GRANITE SLABS 16 TO 18MM THICK UPTO 8'-00"(2.43M) OTHER THAN BLACK REGULAR COLOUR SET OVER BASE COAT OF CEMENT MORTAR (1:8), 20 MM THICK OVER CC BED ALREADY LAID OR RCC ROOF SLAB, INCLUDING NEAT CEMENT SLURRY OF HONEY LIKE CONSISTENCY SPREAD @ 3.3.KGS PER SQM & JOINTED NEATLY WITH WHITE CEMENT PASTE MIXED WITH PIGMENT OF MATCHING SHADE TO FULL DEPTH, INCLUDING COST OF ALL MATERIALS LIKE CEMENT, SAND WATER AND TILESETC., COMPLETE, , LABOUR CHARGES FOR DRESSING OF TILES ETC.,BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE FOR FINISHED ITEM OF WORK. FOR GROUND FLOOR

PROVIDING SKIRTING TO INTERNAL WALLS TO 15 CM HEIGHT / RISERS OF STEPS HIGH POLISHED GRANITE SLABS 16 TO 18MM THICK UPTO 8'-00"(2.43M) OTHER THAN BLACK AND REGULAR COLOURS LENGTH EQUAL TO FLOORING STONES, SET OVER BASE COAT OF CM (1:3) 12 MM THICK WITH CEMENT SLURRY OF HONEY LIKE CONSISTENCY SPREAD AT THE RATE OF 3.30 KGS PER SQM AND JOINTED WITH WHITE CEMENT PASTE MIXED WITH PIGMENT OF MATCHING SHADE TO FULL DEPTH, INCLUDING COST OF ALL MATERIALS LIKE TILES, CEMENT, SAND AND WATER ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE FOR FINISHED ITEM OF WORK, FOR GROUND FLOOR

FLOORING WITH SUPPLY OF NON-SKID RED OR WHITE FULL BODY CERAMIC FLOOR TILES OF SIZE 300 X 300 MM AND THICKNESS BETWEEN 7-8 MM 1ST QUALITY CONFORMING TO IS:13711, IS:13712, IS:13630 (PARTS 1 TO 15) OF ANY COLOUR AND FINISH IN ALL SHADES AND DESIGNS OR AS APPROVED BY THE ENGINEER - IN -CHARGE ,OF APPROVED PATTERN FOR FLOORING SET OVER BASE COAT OF CEMENT MORTAR (1:8), 12 MM THICK OVER CC BED ALREADY LAID OR RCC ROOF SLAB, INCLUDING NEAT CEMENT SLURRY OF HONEY LIKE CONSISTENCY SPREAD @ 3.3.KGS PER SQM & JOINTED NEATLY WITH WHITE CEMENT PASTE TO FULL DEPTH MIXED WITH PIGMENT OF MATCHING SHADE, INCLUDING COST OF ALL MATERIALS LIKE CEMENT, SAND WATER AND TILES, INCLUDING LIFTING (MANUAL) AND ALL LABOUR CHARGES, ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE FOR FINISHED ITEM OF WORK, FOR GROUND FLOOR (APSS.NO:701&707).

PAINTING TO NEW WOOD WORK TWO COATS WITH SYNTHETIC ENAMEL PAINT OVER ONE COAT OF WOOD PRIMER OF APPROVED BRAND AND SHADE INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES FOR PREPARING AND CLEANING THE SURFACE OF DIRT WITH SOAP AND BRUSHES INCLUDING PUTTY AND ALL INCIDENTAL AND OPERATIONAL CHARGES ETC., BUT EXCLUDING GST., (THE RATE INCLUDES ONE COAT OF WOOD PRIMER AND TWO COATS OF PAINT ) (APSS NO.1201, 1207, 1212).COMPLETE FOR FINISHED ITEM OF WORK.

PAINTING TO NEW IRON WORK WITH ONE COAT OF RED OXIDE PRIMER COAT AND TWO COATS WITH SYNTHETIC ENAMEL PAINT OF APPROVED BRAND AND SHADE INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES FOR PREPARING AND CLEANING THE SURFACE OF DIRT WITH SOAP AND BRUSHES INCLUDING PUTTY, ALL INCIDENTAL, OPERATIONAL CHARGES ETC., COMPLETE (THE RATE INCLUDES TWO COATS OF PAINT AND ONE COAT PRIMER) BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK IN ALL FLOOR. (APSS NO.1201, 1207, 1212)

PROVIDING IMPERVIOUS COAT TO EXPOSED RCC ROOF SLAB SURFACE IN CM(1:3), 20MM THICK WITH 1KG OF WATER PROOF COMPOUND PER BAG OF CEMENT LAID OVER ROOF WHEN IT IS GREEN, INCLUDING COST OF ALL MATERIALS, COST & CONVEYANCE OF ALL MATERIALS, INCIDENTAL, OERATIONAL AND LABOUR CHARGES FOR MIXING MORTAR, LAYING, RENDERING SMOOTH AND THREAD LINING, CURING, ROUNDING OFF JUNCTIONS OF WALL AND SLAB ETC, COMPLETE FOR FINISHED ITEM OF WORK. BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS .GROUND FLOOR (APSS.NO: 901&903)

SUPPLYING AND LAYING RAIN WATER DOWN TAKE PIPES WITH 110 MM DIA PVC / SWR PIPES OF APPROVED MAKE OF 4 Kg/cm2 CONFIRMING TO IS:13592-1992, WITH NECESSARY UPVC PIPE CLIPS @ 5' INTERVALS AND JOINTED WITH SOLVENT CEMENT INCLUDING CUTTING OF WALLS AND FLOORS AND MAKING THE SAME GOOD, COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES ETC., BUT EXCLUDING GST - COMPLETE FOR FINISHED ITEM OF WORK. FOR ALL FLOORS

PROVIDING "HYSD/TMT" STEEL BARS OF DIFFERENT DIAMETERS BELOW 36MM DIAMETER Fe 500 GRADE (AS PER IS 1786 - 2008 AND ALL ITS LATEST AMMENDMENTS) FROM Reinforcement Steel (HYSD/TMT) from steel Manufactureres within Telangana with min integrated installed Production Capacity of 2 Lakh MT per annum like AF Star TMT/MS Life TMT, Radha TMT, Sugna TMT FOR REINFORCEMENT INCLUDING CUTTING, BENDING TO REQUIRED SIZES AND SHAPES, PLACING THEM IN POSITION WITH COVER BLOCKS OF APPROVED SHAPE AND SIZE, TYING FIRMLY WITH M.S BINDING WIRE OF SWG, FORMING GRILLS FOR REINFORCEMENT WORKS AS PER APPROVED DESIGNS AND DRAWINGS TO BE SUPPLIED AT THE TIME OF EXECUTION OF WORK INCLUDING COST AND CONVEYANCE OF DEFORMED BARS, BINDING WIRE, COVER BLOCKS AND ALL WASTAGES SUCH AS OVER LAPS, COUPLINGS, WELDED JOINTS, CHAIRS, SPACE BARS ETC., AS DIRECTED BY THE ENGINEER-IN-CHARGE AND ALL OPERATIONAL, INCIDENTAL LABOUR CHARGES SUCH AS CUTTING, BENDING, PLACING IN POSITION, TYING ETC., EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK FOR ALL LENGTHS AS PER DRAWINGS AND TECHNICAL SPECIFICATIONS FOR BARS BELOW 36MM DIA WHERE THEY ARE NOT WELDED.

FULL ROUNDING THE EDGES OF GRANITE STONE SLABS OF ALL THICKNESS INCLUDING POLISHING THE SAME.

PLAIN CEMENT CONCRETE (1:4:8) PROP. USING 20MM GRADED HARD GRANITE MACHINE CRUSHED METAL INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, CENTERING, MACHINE MIXING, LAYING, CURING, FINISHING, ALL OTHER INCIDENTAL, OPERATIONAL, LABOUR CHARGES ETC.,BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS. COMPLETE FOR FINISHED ITEM OF WORK. DUMMY COLUMNS IN GROUND FLOOR (APSS NO: 402).

SUPPLYING AND FIXING IN POSITION OF STAIRCASE RAILING AS PER DRAWING USING STAINLESS STEEL TUBES, SECTIONS, PLATES SHEETS & PIPES OF ALL DIAMETERS OF 304 GRADE INCLUDING LABOUR CHARGES FOR FABRICATION OF STAINLESS STEEL RAILING WORKS USING STAINLESS STEEL WELDING RODS INCLUDING BUFFING, POLISHING, LACQUER FINISHING, TO PRESENT SEAMLESS FINISH ETC., COMPLETE AS DIERCTED BY THE ENGINEER-IN-CHARGE, BUT EXCLUDING GST. FOR FINISHED ITEM OF WORK. FOR GROUND FLOOR

INTERNAL DOOR (DOUBLE SHUTTER): 1.20 X2.10M: SUPPLYING, POSITIONING AND FIXING OF ISI MARK, STANDARD MAKE, FLUSH DOOR SHUTTER OF 35 MM THICK WITH TEAK VENEER ONE SIDE AND COMMERCIAL PLY ON ANOTHER FACE INCLUDING DOOR FRAME MADE WITH MEDIUM TEAK WOOD SCANTLING OF SIZE 125 MM X 75 MM, 6 NOS. OF MS 'Z' HOLD FASTS OF SIZE 230 X 40 X 3 MM, 3 NOS. OF 125 MM BUTT HINGES, 2NOS. 150 MM LONG DOOR HANDLES, 1 NO. ALDROP OF SIZE 250 MM LONG, 1 NO. 200 MM LONG TOWER BOLTS, 1 NO. DOOR STOPPER WITH BOLTS, NUTS, NF SCREWS, COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES FOR MAKING THE FRAME AND FIXING FRAME AND SHUTTER, MINOR EXTRA FIXTURES REQUIRED IF ANY AS DIRECTED BY THE ENGINEER-IN-CHRGE OF THE WORK COMPLETE FOR FINISHED ITEM OF WORK. (ALL FITTINGS AND FIXTURES SHOULD BE OF ALUMINIUM, ISI MARK, GOT APPROVED BY THE ENGINEER-IN-CHARGE). (APSS NO: 1001&1002).

INTERNAL DOOR (SINGLE SHUTTER): 1.05 X2.10M: SUPPLYING, POSITIONING AND FIXING OF ISI MARK, STANDARD MAKE, FLUSH DOOR SHUTTER OF 35 MM THICK WITH TEAK VENEER ONE SIDE AND COMMERCIAL PLY ON ANOTHER FACE INCLUDING DOOR FRAME MADE WITH MEDIUM TEAK WOOD SCANTLING OF SIZE 125 MM X 75 MM, 6 NOS. OF MS 'Z' HOLD FASTS OF SIZE 230 X 40 X 3 MM, 3 NOS. OF 125 MM BUTT HINGES, 2NOS. 150 MM LONG DOOR HANDLES, 1 NO. ALDROP OF SIZE 250 MM LONG, 1 NO. 200 MM LONG TOWER BOLTS, 1 NO. DOOR STOPPER WITH BOLTS, NUTS, NF SCREWS, COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES FOR MAKING THE FRAME AND FIXING FRAME AND SHUTTER, MINOR EXTRA FIXTURES REQUIRED IF ANY AS DIRECTED BY THE ENGINEER-IN-CHRGE OF THE WORK COMPLETE FOR FINISHED ITEM OF WORK. (ALL FITTINGS AND FIXTURES SHOULD BE OF ALUMINIUM, ISI MARK, GOT APPROVED BY THE ENGINEER-IN-CHARGE). (APSS NO: 1001&1002).

SUPPLYING AND FIXING OF UNPLASTICISED POLY VINYL CHLORIDE (UPVC) 3 TRACK SLIDING WINDOWS WITH MESH SHUTTER PROVISION – (ONLY 2-GLASS SHUTTERS) DULY MANUFACTURED USING UPVC REINFORCED PROFILES (COMPOSITION OF PROFILE SHALL CONSISTS A MINIMUM OF 5.5 PHR OF TIO2 AND NOT MORE THAN 12 PHR OF CACO3 FOR EVERY 100 PARTS OF PVC RESIN) OF (80 MM X 52 MM)/ (94 MM X 45 MM) X 2.20MM FOR OUTER FRAMES, (54MMX38MM)/(39 MM X 58 MM) X 2.20 MM FOR SLIDING SHUTTER FRAMES CAPABLE OF MOUNTING SINGLE GLAZING SYSTEM, STRUCTURALLY REINFORCED WITH HOT DIP GALVANIZED UP TO 50 MICRONS OF MINIMUM THICKNESS OF 1.0/1.2 MM PREFABRICATED & WELDED THROUGH FUSION WELDING. THE WINDOW SASH SHALL BE FITTED WITH 5 MM THICK CLEAR FLOAT GLASS OF REPUTED MAKE DULY FIXED WITH GREY COLOUR TPV GASKET FOR SASH & GLAZING BEAD SHALL BE CO- EXTRUDED WITH GREY COLOUR SOFT PVC. SYSTEM SHALL HAVE SINGLE POINT LOCKING WITH TOUCH LOCK AND THE SYSTEM IS TO BE INSTALLED AT THE SITE USING ANCHOR FASTENERS, SILICON RUBBER SEALANT, EASY GLAZING/ DEGLAZING AT SITE ETC., INCLUDING COST AND CONVEYANCE OF ALL MATERIALS, ACCESSORIES, LABOUR CHARGES FOR TRANSPORTATION, ERECTION AT SITE., BUT EXCLUDING GST., COMPLETE FOR FINISHED ITEM OF WORK

DOOR: 0.80X2.1 SUPPLY AND FIXING OF WPC SINGLE DOOR SHUTTER OF 30MM THICK FOR EXISTING DOOR FRAME OF WPC OF SIZE 100MM X 65 MM, INCLUDING 4NOS. OF 125 MM BUTT HINGES, 1 NO. DOOR STOPER, 2NOS. 150 MM LONG DOOR HANDLES, 2NOS ALDROP OF SIZE 300 MM LONG, 1NOS. OF 250 MM LONG TOWER BOLTS WITH BOLTS, NUTS, NF SCREWS INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES FOR FIXING THE FRAME AND SHUTTER ETC., INCLUDING MINOR EXTRA FIXTURES REQUIRED IF ANY AS DIRECTED BY THE ENGINEER-IN-CHRGE OF THE WORK COMPLETE FOR FINISHED ITEM OF WORK. (ALL FITTINGS AND FIXTURES SHOULD BE OF ALLUMINUM, ISI MARK, GOT APPROVED BY THE ENGINEER-IN-CHARGE) (APSSNO:1001&1002) BUT EXCLUDING GST

Providing and fixing factory made solid Wood Polymer Composite (WPC) single extruded Door Frame section of 100*65 MM with encapsulation of 6 MM rigid layer on all external surfaces. The door frame will have a rebate of 32MM/ 37 MM. The two Vertical members are to be joined together with the horizontal member using 8x75 MM long MS Star full thread screws to be used with reverse forward speed control hand drilling machine The ready/assembled door frame is fixed to wall using Z Hand fast 300 MM long hold fast but excluding GST

Providing, supplying & fixing of Top hung Ventilator With Exhaust Fan Provision made out of multi chambered uPVC sections with TPV Gasket for sash & Glazing bead shall be coextruded with Grey colour soft PVC and reinforced with Galvanized Iron profiles throughout the window. The outer frame having a overall size of 60mm x 55 mm x 2.40 mm with reinforcement of 1 mm thickness, Mullion with overall size of 74 mm x 60 mm x 2.40 mm with reinforcement of 1 mm thickness and Sash with overall size of 75 mm x 60 mm x 2.40 mm with reinforcement of 1.0/1.2 mm thickness. (Composition of profile shall consists a minimum of 5.5 PHR of TiO2 and not more than 12 PHR of CaCo3 for every 100 parts of PVC resin).Glazing bead for fixing of glass shall be of size 34 x 20 mm coextruded with soft PVC gasket. Ventilator

SUPPLYING AND FIXING MS GRILLS FOR WINDOWS/VENTILATORS OF ALL SIZES AS DIRECTED BY THE ENGINEER-IN- CHARGE INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE AND LABOUR CHARGES FOR FABRICATION, FIXING BUT EXCLUDING GST. COMPLETE FOR FINISHED ITEM OF WORK M.S.FLATS of ALL SIZES

SUPPLYING AND FIXING MS GRILLS FOR WINDOWS/VENTILATORS OF ALL SIZES AS DIRECTED BY THE ENGINEER-IN- CHARGE INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE AND LABOUR CHARGES FOR FABRICATION, FIXING BUT EXCLUDING GST . COMPLETE FOR FINISHED ITEM OF WORK M.S. SQUARE BARS of ALL SIZES

SUPPLYING MS STRUCTURAL STEEL WORKS LIKE HEAVY STEEL WORKS LIKE TRUSSES, STANCHIONS, HEAVY BEAMS AND GIRDERS INCLUDING COST OF WELDING RODS, POWER CHARGES, FOR ERECTING & FIXING ALL STRUCTURAL STEEL WORKS LIKE HEAVY IRON GRILLS, TRUSSES, STANCHIONS, HEAVY BEAMS AND GIRDERS ERECTING IN POSITION AND FIXING BY USING CHAIN PULLEY BLOCKS, DEREK POLE ARRANGEMENTS AND CRANES ETC., COMPLETE IN POSITION ETC COMPLETE FOR ALL SIZES AS DIRECTED BY THE ENGINEER-IN- CHARGE INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE AND LABOUR CHARGES FOR FABRICATION, FIXING ETC., COMPLETE FOR THE FINISHED ITEM OF WORK M.STUBES OF ALL SIZES

CELL DOOR: MANUFACTURING, SUPPLYING AND FIXING OF IRON GRATED DOOR OF SIZE 1.85 X 2.25 M (TO LOCK UP ROOM) MADE WITH I.S.M.C. CHANNEL 150X50X10mm SECTION OF CHANNEL AT TOP AND BOTTOM WITH VERTICAL MS ROUNDS OF 20 mm DIA @ 100 mm C/C HORIZONTAL FLAT OF SIZE 75mmX10mm FOR SHUTTER @ 0.30 MM C/C AND SIDE SUPPORTS WITH MS PLATE OF SIZE 150mmX10mm WHICH WILL BE WELDED TO THE CHANNEL AT TOP AND BOTTOM AND ALSO LOCKING ARRANGEMENTS WITH ALDROP MADE WITH 20 mm DIA MS ROUNDS INCLUDING COST, LABOUR CHARGES FOR CUTTING, BENDING, WELDING CHARGES, MAKING HOLES AND HOLD FAST OF SIZE 50X8mm FLAT OF 300mm LONG AND INCLUDING THE COST OF MISCELLANEOUS ACCESSORIES, TRANSPORTATION TO SITE AND PAINTING ONE COAT WITH RED OXIDE ETC., BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK AS PER DRAWING.

Painting with Exterior Emulsion Paint of approved make (ACE from Asian Paint) and colour to the Exterior Faces of walls as directed 2 coats by diluting 1 lit. of Emulsion Paint with a maximum 750 ml of water within an interval of not less than 6 hours between two coats over 1 coat of Exterior Wall Primer by diluting 1 Lit. of primer with 1 Lit. of water (Total 3 coats) with surface preparation etc., as per standard specification including cost and conveyance of all materials, brushes, labour charges, curing, scaffolding and all other incidental and operational charges etc., complete for finished item of work in all floors. (APSS No.908).

Supplying and fixing of Unplasticised Poly Vinyl Chloride (UPVC) openable doors with openable shutters duly manufactured using UPVC reinforced profiles (Composition of profile shall consists a minimum of 5.5 PHR of TiO2 and not more than 12 PHR of CaCo3 for every 100 parts of PVC resin) of 60 mm x 55 mm x 2.40 mm for outer frames, 74 mm x 60 mm x 2.40 mm for mullion sections as per the need and 102 mm x 60 mm x 2.40 mm for openable shutter frame capable of ounting single glazing system structurally reinforced with hot dip galvanized up to 50 microns of minimum thickness of 1.2 mm prefabricated & welded through fusion welding the door sash shall be fitted with 6 mm thick clear float glass of reputed make duly fixed with Grey colour TPV Gaskets for sash & Glazing bead shall be co-extruded with Grey colour soft PVC System shall be provided with 4 no’s of 3D Hinges for each shutter and multipoint locking with keys with raiser wedges for smooth operation and the system is to be installed at the site using anchor fasteners, silicon rubber sealant, easy glazing/ deglazing at site etc., including cost and conveyance of all materials, accessories, labour charges for transportation, erection at site complete for finished item of work

VENTILATORS (FIXED GLAZING): SUPPLY AND FIXING VENTILAORS WITH SEASONED SAL WOOD FRAME AND MULLION OF SIZE 100MMX75MM, FIXING 3 NOS. OF 10 MM SQUARE BARS HORIZONTALLY TO FRAME, MAKING SLANTING GROOVES OF 6 MM WIDE TO THE FRAME, SUPPLYING AND FIXING OF 5MM THICK 125 MM WIDE PIN HEADED GLASS IN THE GROOVES, INCLUDING SUPPLYING AND FIXING OF 4 NOS. OF 250X50X8 MM MS HOLD FASTS, COST AND CONVEYANCE OF BOLTS, NUTS, NF SCREWS, ALL OTHER MATERIALS TO SITE, LABOUR CHARGES, MINOR EXTRA FIXTURES REQUIRED IF ANY AS DIRECTED BY THE ENGINEER-IN-CHRGE OF THE WORK ETC., COMPLETE FOR FINISHED ITEM OF WORK.

PAINTING TO NEW WALLS WITH THREE (3) COATS OF SYNTHETIC POLYMER LUXURY PLASTIC EMULSION /SOLVENT BASED LUSTRE PAINT OF SUPERIOR GRADE HAVING (VOC < 50 GMS./LIT) OF APPROVED BRAND AND SHADE (ASIAN /BERGER /NEROLAC /SAICOAT /INDOCEM OR EUIVALENT) OVER ONE COAT OF PRIMER OF APP BRAND AFTER THOUROULY BRUSHING THE SURFACE TO REMOVE ALL DIRT AND REMAINS OF LOOSE POWDER MATERIALS INCLUDING COST OF ALL MATERIALS TO THE INTERIOR FACES OF WALLS AS DIECTED 2COATS BY DILUTING 1LIT OF EMULSION PAINT WITH A MAXIMUM 750ML OF WATER WITH AN INTERVAL OF NOT LESS THAN 6 HOURS BETWEEN TWO COATS (TOTAL3 COATS) WITH SURFACE PREPARATION ETC., AS PER STANDARD SPECIFICATION INCLUDING COST AND CONVEYANCE OF ALL MATERIALS, BRUSHES, LABOUR CHARGES, CURING, SCAFFOLDING LIFTING(MANUAL) AND ALL OTHER INCIDENTAL AND OPERATIONAL CHARGES ETC.,BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK

SUPPLY AND FIXING OF 15.90MM OD PIPE - SDR 11 ASHIRVAD / ASTRAL FLOW GUARD OR EQUIVALENT CPVC PIPES AND FITTINGS TO MEET THE REQUIREMENTS OF ASTM-D 2846 AND ARE PRODUCED IN CTS (COPPER TUBE SIZES 1/2" TO 2") ASHIRVAD FLOWGUARDS SDR 11 MADE FROM IDETICAL CPVC COMPOUNDS HAVING THE SAME PHYSICAL PROPERTIES FOR HOT AND COLD WATER (IS 15778-2007) INCLUDING COST AND CONVEYANCE OF PIPE & ITS FITTINGS AND ALL MATERIALS TO SITE, LABOUR CHARGES ETC.,BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK.

SUPPLY AND FIXING OF 22.20MM OD PIPE - SDR 11 ASHIRVAD / ASTRAL FLOW GUARD OR EQUIVALENT CPVC PIPES AND FITTINGS TO MEET THE REQUIREMENTS OF ASTM-D 2846 AND ARE PRODUCED IN CTS (COPPER TUBE SIZES 1/2" TO 2") ASHIRVAD FLOWGUARDS SDR 11 MADE FROM IDETICAL CPVC COMPOUNDS HAVING THE SAME PHYSICAL PROPERTIES FOR HOT AND COLD WATER (IS 15778-2007) INCLUDING COST AND CONVEYANCE OF PIPE & ITS FITTINGS AND ALL MATERIALS TO SITE, LABOUR CHARGES ETC.,BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK.

SUPPLY AND FIXING OF 28.60MM OD PIPE - SDR 11 ASHIRVAD / ASTRAL FLOW GUARD OR EQUIVALENT CPVC PIPES AND FITTINGS TO MEET THE REQUIREMENTS OF ASTM-D 2846 AND ARE PRODUCED IN CTS (COPPER TUBE SIZES 1/2" TO 2") ASHIRVAD FLOWGUARDS SDR 11 MADE FROM IDETICAL CPVC COMPOUNDS HAVING THE SAME PHYSICAL PROPERTIES FOR HOT AND COLD WATER (IS 15778-2007) INCLUDING COST AND CONVEYANCE OF PIPE & ITS FITTINGS AND ALL MATERIALS TO SITE, LABOUR CHARGES ETC.,BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK.

SUPPLY AND FIXING OF 41.30 MM OD PIPE - SDR 11 ASHIRVAD / ASTRAL FLOW GUARD OR EQUIVALENT CPVC PIPES AND FITTINGS TO MEET THE REQUIREMENTS OF ASTM-D 2846 AND ARE PRODUCED IN CTS (COPPER TUBE SIZES 1/2" TO 2") ASHIRVAD FLOWGUARDS SDR 11 MADE FROM IDETICAL CPVC COMPOUNDS HAVING THE SAME PHYSICAL PROPERTIES FOR HOT AND COLD WATER (IS 15778-2007) INCLUDING COST AND CONVEYANCE OF PIPE & ITS FITTINGS AND ALL MATERIALS TO SITE, LABOUR CHARGES ETC.,BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK.

SUPPLYING AND FIXING 15MM BRASS BIB TAP CP FINISH - INDIAN MAKE HEAVY DUTY FULL TURN 300GMS AS DIRECTED BY THE ENGINEER-IN-CHARGE, INCLUDING COST AND CONVEYANCE OF PIPE & ITS FITTINGS AND ALL MATERIALS TO SITE, LABOUR CHARGES ETC., BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK.

SUPPLYING AND FIXING GM GATE (PEET) VALVES - 25 MM NB SIZEINDIAN MAKE HEAVY DUTY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE AND LABOUR CHARGES ETC., BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK

SUPPLYING AND FIXING GM GATE (PEET) VALVES - 20 MM NB SIZEINDIAN MAKE HEAVY DUTY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE AND LABOUR CHARGES ETC., BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK

SUPPLYING AND FIXING 76.2MM (3") DIA UV RESISTANT UPVC SWR NAHANI TRAP WITH JALI OF APPROVED ISI BRAND INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR ETC., BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK.

SUPPLYING AND LAYING 75 MM DIA SINGLE SOCKET PVC / SWR PIPES OF APPROVED MAKE OF 4 Kg/cm2 CONFIRMING TO IS:13592-1992, WITH NECESSARY UPVC PIPE CLIPS @ 5' INTERVALS AND LABOUR CHARGES FOR LAYING, FIXING, AND COMMISSIONING THE PVC PIPES INCLUDING COUPLERS/ BENDS/TEES ETC., INCLUDING FIXING NECCESSARY FITTINGS LIKE BENDS, PLUGS, COUPLERS, JUNCTIONS, TEES ETC., WITH SOLVENT JOINTING AS PER STANDARDS INCLUDING CUTTING OF WALLS AND FLOORS AND MAKING THE SAME GOOD, INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES ETC.,BUT EXCLUDING GST., COMPLETE FOR FINISHED ITEM OF WORK.

SUPPLYING AND FIXING APPROVED MAKE WASH DOWN EUROPEAN WATER CLOSET OF 1ST QUALITY CONFORMING TO IS:2556-PART-2-2004 OF WHITE GLAZED WITH 'P' TRAP, INCLUDING SUPPLYING AND FIXING BEST INDIAN MAKE PLASTIC SEAT AND LID FOR EUROPEAN WATER CLOSETS WITH RUBBER OR PLASTIC BUFFERS AS PER IS 2548-1996 AND SUPPLY & FIXING OF PVC LOW LEVEL SYSTEM WITH INTERNAL COMPONENTS & SHORT BEND: 8 LITERS CAPACITY SINGLE FLUSH & SUPPLYING & FIXING 15 MM NOMINAL SIZE PVC CONNECTION WITH BRASS UNION NUT C.P COATED INCLUDING CUTTING THE WALLS AND FLOORS AND MAKING GOOD THE SAME, COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES ETC., BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK

SUPPLYING & FIXING INDIAN MAKE FLAT BACK WASH HAND BASIN 1ST QUALITY CONFORMING TO IS:2556-PART-4:1972 WITH WASTE FITTINGS LIKE RUBBER PLUG, CHAIN, 32 MM NOMINAL SIZE C.P. FITTING WITH PARALLEL PIPE THREAD CONFORMING TO IS:2963-1979 AND FITTED WITH 15 MM NOMINAL BORE CHROMIUM PLATED PILLAR TAP OF 1ST QUALITY INDIAN MAKE 400 GRAMS SEIKO/ SENIOR/ NICE/ ESSO OR EQUIVALENT COMPLETE WITH STANDARD CI BRACKETS INCLUDING WOODEN BLOCK: 550 X 400 MM -SINGLE C.P. PILLAR COCK INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES ETC., COMPLETE FOR FINISHED ITEM OF WORK.

S&F OF 15 MM PREMIUM VARIETY CHROMIUM PLATED FINISH BRASS BODY WALL MIXER WITH HAND SHOWER WITH A PROVISION FOR OVER HEAD SHOWER WITH 115 MM LONG BEND PIPE ON UPPER SIDE, CONNECTING LEGS & WALL FLANGES CONFORMING TO IS 8931 WITH 10 YEARS WARRANTY ,INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES ETC., BUT EXCLUDING GST., COMPLETE FOR FINISHED ITEM OF WORK.

S&F OF CHROMIUM PLATED FINISH BRASS BODY QUARTER TURN BIBCOCK CUM HEALTH FAUCET WITH 1M LONG TUBE AND WALL HOOK WITH 10 YEARS WARRANTY ,INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES ETC., BUT EXCLUDING GST ., COMPLETE FOR FINISHED ITEM OF WORK.

SUPPLYING AND FIXING BEST INDIAN MAKE 609.6X457.2mm T.V SHAPE MIRROR WITH PLASTIC FRAME MIRROR INCLUDING WOODEN BLOCKS, SCREWS ETC., INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES ETC., BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK

SUPPLYING AND LAYING 110 MM DIA SINGLE SOCKET PVC / SWR PIPES OF APPROVED MAKE OF 4 Kg/cm2 CONFIRMING TO IS:13592-1992, WITH NECESSARY UPVC PIPE CLIPS @ 5' INTERVALS AND JOINTED WITH SOLVENT CEMENT INCLUDING CUTTING OF WALLS AND FLOORS AND MAKING THE SAME GOOD, AND LABOUR CHARGES FOR LAYING, FIXING, AND COMMISSIONING THE PVC PIPES INCLUDING COUPLERS/ BENDS/TEES ETC., INCLUDING FIXING NECCESSARY FITTINGS LIKE BENDS PLUGS, COUPLERS, JUNCTIONS, TEES ETC., WITH SOLVENT JOINTING AS PER STANDARDS, INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES ETC., BUT EXCLUDING GST., COMPLETE FOR FINISHED ITEM OF WORK.

SUPPLYING AND FIXING NP SOAP DISH HEAVY TYPE WITH NP SCREWS INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES ETC.,BUT EXCLUDING GST., COMPLETE FOR FINISHED ITEM OF WORK.

SUPPLYING AND FIXING 19.04 MM DIA, 609.60 MM LONG ALUMINUM ANODISED TOWEL ROD WITH BRACKETS AND SCREWS INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES ETC., BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK .

SUPPLYING AND FIXING OF 150MMX100MM SWG GULLY TRAP CONFIRMING TO ISI 651 & 4127 WITH CI GRATING AND CONSTRUCTION OF BRICK MASONRY INTERMEDIATE CHAMBER OF SIZE 20"X14"X12" IN CM (1:6) OVER CC (1:5:10) PROP. BED OF SIZE 20"X14"X4" AND PLASTERING WITH 12MM THICK IN CM (1:4) PROP. BOTH INSIDE AND OUTSIDE SURFACES AND FITTED WITH 9"X12" (230X305MM) RCC (1:11/2:3) 1 1/2" THICK COVER INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, FOR FINISHED ITEM OF WORK COMPLETE.

CONSTRUCTING 1'-6" X 1'-6" BRICK MASONARY INSPECTION CHAMBER WITH CM (1:6) PROP. USING FLY ASH BRICKS OF 225MM THICK , AND FITTED WITH 457.2 X 457.2 MM (1'-6'' X 1'-6") RCC COVER UP TO A DEPTH OF 914.4 MM (3'-0") AND LAYING CEMENT CONCRETE (1:4:8) 150 MM THICK USING 40 MM HBG METAL AND PCC (1:2:4) BENCHING AND CHANNEL 100 MM THICK INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, SAND, BRICKS, WATER ETC.,TO SITE ,COST OF LABOUR CHARGES LIKE MIXING CEMENT MORTAR, CONSTUCTING MASONARY, LIFT CHARGES, CURING ETC., COMPLETE INCLUDING COST OF STEEL AND ITS FABRICATION, BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, FOR FINISHED ITEM OF WORK AS PER STANDARD SPECIFICATION

SUPPLYING AND FIXING 110 MM DIA UV RESISTANT UPVC SWR SINGLE TEE (WITH DOOR) AS PER ISI STANDARDS INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR, EXCLUDING GST ETC., COMPLETE FOR FINISHED ITEM OF WORK.

SUPPLYING AND FIXING 75 MM DIA UV RESISTANT UPVC SWR SINGLE TEE (WITH DOOR) AS PER ISI STANDARDS INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR, EXCLUDING GST ETC., COMPLETE FOR FINISHED ITEM OF WORK.

SUPPLYING AND FIXING 110 MM DIA UV RESISTANT UPVC SWR PLAIN BEND 87.5 DEGREES AS PER ISI STANDARDS INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR, EXCLUDING GST ETC., COMPLETE FOR FINISHED ITEM OF WORK.

SUPPLYING AND FIXING 75 MM DIA UV RESISTANT UPVC SWR PLAIN BEND 87.5 DEGREES AS PER ISI STANDARDS INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR, EXCLUDING GST ETC., COMPLETE FOR FINISHED ITEM OF WORK.

S&F OF CHROMIUM PLATED FINISH BRASS BODY QUARTER TURN BIBCOCK CUM HEALTH FAUCET WITH 1M LONG TUBE AND WALL HOOK WITH 10 YEARS WARRANTY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES ETC., BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK

SUPPLYING, LAYING, JOINTING AND TESTING OF 110 MM DIA PVC / SWR PIPES OF APPROVED MAKE OF 4 Kg/cm2 CONFIRMING TO IS:13592-1992, AND JOINTING WITH SOLVENT CEMENT INCLUDING EXCAVATION OF TRENCHES AND SOCKET PITS IN ANY SOIL (EXCEPT ROCK REQUIRING BLASTING) UP TO 0.91M DEPTH AND REFILLING WITH EXCAVATED SOILS, WATERING, TAMPING, COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES ETC., BUT EXCLUDING GST., COMPLETE FOR FINISHED ITEM OF WORK.

SUPPLYING AND FIXING 110 MM DIA UV RESISTANT UPVC SWR DOOR BEND 87.5 DEGREES AS PER ISI STANDARDS INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR, EXCLUDING GST ETC., COMPLETE FOR FINISHED ITEM OF WORK.

SUPPLYING AND FIXING 75 MM DIA UV RESISTANT UPVC SWR DOOR BEND 87.5 DEGREES AS PER ISI STANDARDS INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR, EXCLUDING GST ETC., COMPLETE FOR FINISHED ITEM OF WORK.

SUPPLYING AND FIXING 110 MM DIA UV RESISTANT UPVC SWR COWL AS PER ISI STANDARDS INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR, EXCLUDING GST ETC., COMPLETE FOR FINISHED ITEM OF WORK.

SUPPLYING AND FIXING 75 MM DIA UV RESISTANT UPVC SWR COWL AS PER ISI STANDARDS INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR, EXCLUDING GST ETC., COMPLETE FOR FINISHED ITEM OF WORK.

PROVIDING AND PLACING ON TERRACE POLYTHELENE WATER STORAGE TANKS (AT ALL FLOOR LEVELS) DOUBLE LAYER APPROVED BRAND AND MNUFACTURE WITH COVER AND SUITABLE LOCKING ARRANGEMENTS MAKING NECESSARY HOLES FOR INLET & OUTLETS AND OVERFLOW PIPES BUT WITHOUT FITTINGS & BASE SUPPORT FOR TANKS, MAKING GOOD THE SAME TO ENSURE LEAK PROOF WITH AN APPROPRIATE MASONARY PLATFORM INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR ETC.,BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK AS DIRECTED BY THE ENGINEER -IN- CHARGE

SUPPLY AND FIXING OF 28.60MM OD PIPE - SDR 13.5 ASHIRVAD / ASTRAL FLOW GUARD OR EQUIVALENT CPVC PIPES AND FITTINGS TO MEET THE REQUIREMENTS OF ASTM-D 2846 AND ARE PRODUCED IN CTS (COPPER TUBE SIZES 1/2" TO 2") ASHIRVAD FLOWGUARDS SDR 11 MADE FROM IDETICAL CPVC COMPOUNDS HAVING THE SAME PHYSICAL PROPERTIES FOR HOT AND COLD WATER (IS 15778-2007) INCLUDING COST AND CONVEYANCE OF PIPE & ITS FITTINGS AND ALL MATERIALS TO SITE, LABOUR CHARGES ETC.,BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK.

SUPPLY AND FIXING OF 22.20MM OD PIPE - SDR 13.5 ASHIRVAD / ASTRAL FLOW GUARD OR EQUIVALENT CPVC PIPES AND FITTINGS TO MEET THE REQUIREMENTS OF ASTM-D 2846 AND ARE PRODUCED IN CTS (COPPER TUBE SIZES 1/2" TO 2") ASHIRVAD FLOWGUARDS SDR 11 MADE FROM IDETICAL CPVC COMPOUNDS HAVING THE SAME PHYSICAL PROPERTIES FOR HOT AND COLD WATER (IS 15778-2007) INCLUDING COST AND CONVEYANCE OF PIPE & ITS FITTINGS AND ALL MATERIALS TO SITE, LABOUR CHARGES ETC.,BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK.

CONSTRUCTING 914.0 MM ( 3'-0") DIA BRICK MASONARY MAN HOLE AS PER IS-4111:PART-1:1986 WITH CM (1:6) PROP. USING FLY ASH BRICKS OF 225MM THICK FROM APPROVED SOURCE HAVING A MINIMUM CRUSHING STRENGTH OF 5N/SQ.MM INCLUDING PLASTERING WIH CM(1:3) PROP. 12 MM THICK BOTH INSIDE AND OUTSIDE, FITTED WITH 20'' DIA RCC COVERS AND FRAMES, INCLUDING EXCAVATING PITS UP TO A DEPTH OF 914.4 MM (3'-0") IN ALL SORTS OF SOILS (EXCLUDING ROCK) AND LAYING CEMENT CONCRETE (1:4:8) 150 MM THICK USING 40 MM HBG METAL AND PCC (1:2:4) BENCHING AND CHANNEL 100 MM THICK AS PER STANDARD SPECIFICATION AND INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, COST OF ALL INCIDENTAL AND OPERATIONAL, LABOUR CHARGES LIKE MIXING CEMENT MORTAR, CONSTRUCTING MASONRY, CURING ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE FOR FINISHED ITEM OF WORK AS PER STANDARD SPECIFICATION.

SUPPLYING AND LAYING 110 MM DIA SINGLE SOCKET PVC / SWR PIPES OF APPROVED MAKE OF 6Kg/cm2 CONFIRMING TO IS:13592-1992, WITH NECESSARY UPVC PIPE CLIPS @ 5' INTERVALS AND JOINTED WITH SOLVENT CEMENT INCLUDING CUTTING OF WALLS AND FLOORS AND MAKING THE SAME GOOD, AND LABOUR CHARGES FOR LAYING, FIXING, AND COMMISSIONING THE PVC PIPES INCLUDING COUPLERS/ BENDS/TEES ETC., INCLUDING FIXING NECCESSARY FITTINGS LIKE BENDS PLUGS, COUPLERS, JUNCTIONS, TEES ETC., WITH SOLVENT JOINTING AS PER STANDARDS INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES ETC., COMPLETE FOR FINISHED ITEM OF WORK.

SUPPLYING AND LAYING 110 MM DIA SINGLE SOCKET PVC / SWR PIPES OF APPROVED MAKE OF 4 Kg/cm2 CONFIRMING TO IS:13592-1992, WITH NECESSARY UPVC PIPE CLIPS @ 5' INTERVALS AND JOINTED WITH SOLVENT CEMENT INCLUDING CUTTING OF WALLS AND FLOORS AND MAKING THE SAME GOOD, AND LABOUR CHARGES FOR LAYING, FIXING, AND COMMISSIONING THE PVC PIPES INCLUDING COUPLERS/ BENDS/TEES ETC., INCLUDING FIXING NECCESSARY FITTINGS LIKE BENDS PLUGS, COUPLERS, JUNCTIONS, TEES ETC., WITH SOLVENT JOINTING AS PER STANDARDS INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES ETC., COMPLETE FOR FINISHED ITEM OF WORK.

SUPPLYING, LAYING, JOINTING AND TESTING OF 110 MM DIA PVC / SWR PIPES OF APPROVED MAKE OF 4 Kg/cm2 CONFIRMING TO IS:13592-1992, AND JOINTING WITH SOLVENT CEMENT INCLUDING EXCAVATION OF TRENCHES AND SOCKET PITS IN ANY SOIL (EXCEPT ROCK REQUIRING BLASTING) UP TO 0.91M DEPTH AND REFILLING WITH EXCAVATED SOILS, WATERING, TAMPING, COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES ETC., COMPLETE FOR FINISHED ITEM OF WORK.

EARTH WORK EXCAVATION FOR FOUNDATIONS AND DEPOSITING ON BANK, FOR ALL LIFTS AND WITH AN INITIAL LEAD OF 10M INCLUDING ALL INCIDENTAL, OPERATIONAL, LABOUR CHARGES SUCH AS SHORING, SHEETING, PLANKING, STRUTTING, DEWATERING SITE CLEARANCE, CLEARING SHURBS, BRUSHWOOD, UNDER GROWTH AND SMALL TREES NOT EXCEEDING 300 MM GIRTH, MEASURED AT ONE METRE ABOVE GROUND ETC., COMPLETE FOR FINISHED ITEM OF WORK INCLUDING DEWATERING CHARGES ETC AS PER SS - 20 B FOR STIFF BLOCK COTTON SOIL , HARD RED EARTH, MURRAM, ORDINARY GRAVEL - mechanical MEANS UP TO 3M DEPTH - FOUNDATION OF BUILDING (APSS 308).

CEMENT CONCRETE (1:4:8) PROP. USING 40MM HARD GRANITE MACHINE CRUSHED METAL WITH MACHINE MIXING UP TO PLINTH LEVEL INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LAYING, CURING, FINISHING, ALL OTHER INCIDENTAL, OPERATIONAL, LABOUR ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE FOR FINISHED ITEM OF WORK. FOUNDATION BED AND UNDER STONE SLAB FLOORING. (APSS NO: 402).

RE-FILLING WITH USEFUL AVAILABLE EXCAVATED EARTH OTHER THAN EXPANSIVE SOILS LIKE RED EARTH AND ORDINARY GRAVEL ETC., (EXCLUDING ROCK) IN TRENCHES, SIDES OF FOUNDATIONS AND BASEMENT WITH INITIAL LEAD IN LAYERS NOT EXCEEDING 15 CM THICK, CONSOLIDATING EACH DEPOSITED LAYER BY WATERING AND RAMMING INCLUDING COST AND CONVEYANCE OF WATER TO WORK SITE AND ALL INCIDENTAL, OPERATIONAL, LABOUR CHARGES , HIRE CHARGES OF T & P ETC., COMPLETE FOR FINISHED ITEM OF WORK. (APSS NO. 309 & 310)

VRCC M-20 NOMINAL MIX (CEMENT : FINE AGGREGATE : COARSE AGGREGATE) CORRESPONDING TO TABLE 9 OF IS 456 USING 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND) , COARSE AGGREGATE, WATER ETC., TO SITE AND INCLUDING SEIGNIORAGE CHARGES, SALES & OTHER TAXES ON ALL MATERIALS, SHUTTERING, CENTERING WITH STEEL PLATES, ALL INCIDENTAL, OPERATIONAL AND LABOUR CHARGES SUCH AS MACHINE MIXING, LAYING CONCRETE, VIBRATING, CURING ETC., COMPLETE BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK. FOR THICKNESS OF BOTTOM SLAB (APSS NO.403)

RCC M - 20 NOMINAL MIX (Cement:fine aggregate: coarse aggregate) CORRESPONDING TO TABLE 9 OF IS 456 USING 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND), COARSE AGGREGATE, WATER ETC., TO SITE AND INCLUDING SEIGNIORAGE CHARGES, SALES & OTHER TAXES ON ALL MATERIALS INCLUDING ALL OPERATIONAL, INCIDENTAL AND LABOUR CHARGES SUCH AS MACHINE MIXING, LIFTING ( MANNUAL), LAYING CONCRETE, CURING ETC.,COMPLETE AND PROVIDING CENTERING USING CASURINA BALLIES, BAMBOOS, WOODEN REAPERS, RUNNERS, WOOD POSTS, WALL PLATES, STEEL CENTERING PLATES ETC., FOR UNSUPPORTED HIEGHT OF 3.66M BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK (APSS NO.403) FOR RCC SIDE WALLS OF 230 MM THICK

VRCC M-20 NOMINAL MIX (CEMENT : FINE AGGREGATE : COARSE AGGREGATE) CORRESPONDING TO TABLE 9 OF IS 456 USING 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND) , COARSE AGGREGATE, WATER ETC., TO SITE, SEIGNIORAGE, SALES & OTHER TAXES ON ALL MATERIALS, ALL INCIDENTAL, OPERATIONAL AND LABOUR CHARGES SUCH AS MACHINE MIXING, LIFTING (MANUAL),LAYING CONCRETE, VIBRATING, CURING ETC., COMPLETE AND PROVIDING CENTERING USING CASURINA BALLIES, BAMBOOS, WOODEN REAPERS, RUNNERS, WOOD POSTS, WALL PLATES, STEEL CENTERING PLATES ETC., FOR UNSUPPORTED HIEGHT OF 3.66M BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK. FOR SLABS OF 150 MM THICK (APSS NO.403)

PROVIDING IMPERVIOUS COAT TO EXPOSED RCC ROOF SLAB SURFACE IN CM(1:3), 20MM THICK WITH 1KG OF WATER PROOF COMPOUND PER BAG OF CEMENT LAID OVER ROOF WHEN IT IS GREEN, INCLUDING COST OF ALL MATERIALS, COST & CONVEYANCE OF ALL MATERIALS, INCIDENTAL, OERATIONAL AND LABOUR CHARGES LIFTING (MANUAL) FOR MIXING MORTAR, LAYING, RENDERING SMOOTH AND THREAD LINING, , CURING, ROUNDING OFF JUNCTIONS OF WALL AND SLAB ETC,, BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE FOR FINISHED ITEM OF WORK. Ground FLOOR (APSS.NO: 901&903)

PROVIDING "HYSD/TMT" STEEL BARS OF DIFFERENT DIAMETERS BELOW 36MM DIAMETER Fe 500 GRADE (AS PER IS 1786 - 2008 AND ALL ITS LATEST AMMENDMENTS) FROM PRIMARY STEEL PRODUCERS LIKE TATA, SAIL, VSP, JSW & SHYAM STEEL FOR REINFORCEMENT INCLUDING CUTTING, BENDING TO REQUIRED SIZES AND SHAPES, PLACING THEM IN POSITION WITH COVER BLOCKS OF APPROVED SHAPE AND SIZE, TYING FIRMLY WITH M.S BINDING WIRE OF SWG, FORMING GRILLS FOR REINFORCEMENT WORKS AS PER APPROVED DESIGNS AND DRAWINGS TO BE SUPPLIED AT THE TIME OF EXECUTION OF WORK INCLUDING COST AND CONVEYANCE OF DEFORMED BARS, BINDING WIRE, COVER BLOCKS AND ALL WASTAGES SUCH AS OVER LAPS, COUPLINGS, WELDED JOINTS, CHAIRS, SPACE BARS ETC., AS DIRECTED BY THE ENGINEER-IN-CHARGE AND ALL OPERATIONAL, INCIDENTAL LABOUR CHARGES SUCH AS CUTTING, BENDING, PLACING IN POSITION, TYING ETC., COMPLETE FOR FINISHED ITEM OF WORK FOR ALL LENGTHS AS PER DRAWINGS AND TECHNICAL SPECIFICATIONS FOR BARS BELOW 36MM DIA WHERE THEY ARE NOT WELDED.

CABIN TABLE BIG: MAIN TABLE SIZE SIZE: 2000L X 750W X 750 HT , SIDE TABLE SIZE 900W X 450D X 690HT,SPECIFICATION: TABLE & VERTICLES TOP - 25MM THICK PRELAMINATED PARTICLE BOARD ,ALL THE EXPOSED EDGES FINISHED WITH 2MM EDGE LIPPING END SUPPORT - SIDE RUNNER WITH 18MM PRELAMINATED BOARD PROVISION 63MM DIA GROMET CUT-OUT WITH ABS CAP & ALL HRAWARE ARE OF EBCO MAKE AS PER THE CATALOGUE AND SAMPLES APPROVED BY THE ENGINEER-IN -CHARGE

CABIN TABLE SMALL: MAIN TABLE SIZE SIZE: 1500L X 750W X 750 HT , SIDE TABLE SIZE 900W X 450D X 690HT,SPECIFICATION: TABLE & VERTICLES TOP - 25MM THICK PRELAMINATED PARTICLE BOARD ,ALL THE EXPOSED EDGES FINISHED WITH 2MM EDGE LIPPING END SUPPORT - SIDE RUNNER WITH 18MM PRELAMINATED BOARD PROVISION 63MM DIA GROMET CUT-OUT WITH ABS CAP & ALL HRAWARE ARE OF EBCO MAKE AS PER THE CATALOGUE AND SAMPLES APPROVED BY THE ENGINEER-IN -CHARGE

WORKSTATION ( L-SHAPE) (1.50M) : SPECIFICATION: TABLE TOP: 25MM THICK PRE-LAMINATE PARTICLE BOARD WITH 2MM PVC EDGE LIPPING ON ALL EXPOSED EDGES. SCREEN -8MM THICK SANDWICH DUCO PAINTED GALSS 300MM HEIGHTR STRUCTURE: MS POWDER COATED PERFORM LEGS (50X50). MODESTY PANEL: 12MM THICK PLT MODESTY ON PASSAGE SIDE OF 450MM HT. WIRE MANAGEMENT : RACEWAYS 300MM HT X 70MM THK WITH PLB FACIA PROVIDED BELOW TABLE TOP ON MAIN SPINE FOR POWER & DATA CABLE MANAGEMENT. 63MM DIA GORMET CUT-OUT WITH ABS CAP (WITH SOFT CLOSURE) WITHOUT SOCKETS & SWITCHES ARE PROVIDED. SIZE: 1500 X 600 X 750 & 1200 X 400 X 750 AS PER THE CATALOGUE AND SAMPLES APPROVED BY THE ENGINEER-IN -CHARGE

WORKSTATION LINEAR (1.20M): SPECIFICATION: TABLE TOP: 25MM THICK PRE-LAMINATE PARTICLE BOARD WITH 2MM PVC EDGE LIPPING ON ALL EXPOSED EDGES. SCREEN -8MM THICK SANDWICH DUCO PAINTED GALSS 300MM HEIGHTR STRUCTURE: MS POWDER COATED PERFORM LEGS (50X50). MODESTY PANEL: 12MM THICK PLT MODESTY ON PASSAGE SIDE OF 450MM HT. WIRE MANAGEMENT : RACEWAYS 300MM HT X 70MM THK WITH PLB FACIA PROVIDED BELOW TABLE TOP ON MAIN SPINE FOR POWER & DATA CABLE MANAGEMENT. 63MM DIA GORMET CUT-OUT WITH ABS CAP (WITH SOFT CLOSURE) WITHOUT SOCKETS & SWITCHES ARE PROVIDED. SIZE: 1200 X 600 X 750 AS PER THE CATALOGUE AND SAMPLES APPROVED BY THE ENGINEER-IN -CHARGE

MOBILE PEDESTAL: SPECIFICATION: TWO DRAWER MOBILE PEDESTAL MADE WITH 18MM PRELAMINATED PARTICLE BOARD & 9MM FOR BACK PANLE & ALL EXPOSED AREAS ARE FINISHED WITH 2MM EDGBAND. SIZE: 450 X 450 X 600 AS PER THE CATALOGUE AND SAMPLES APPROVED BY THE ENGINEER-IN -CHARGE

KEY BOARD-ABS WITH MOUSEPAD. AS PER THE CATALOGUE AND SAMPLES APPROVED BY THE ENGINEER-IN -CHARGE

CPU TROLLEY WITH CASTORS. AS PER THE CATALOGUE AND SAMPLES APPROVED BY THE ENGINEER-IN -CHARGE

LOW HEIGHT STORAGE : SUPPLY & FIXING FULL HEIGHT STORAGE SIZE 900W X 400D X 750HT - CONSISTING OF STRUCTURE IS MADE OUT OF 18MM PRE LAMINATED BOARDS (PLB). TOP IS 25MM THICK PLB. THE BACK OF THE UNIT IS MADE FROM 9MM PLB. THE UNITS ARE ASSEMBLED BY KNOW DOWN FITTINGS SUCH AS MINIFIX & DOWELS. THE SHELVES ARE MADE OUT OF 18MM PLB, WHICH ARE ADJUSTABLE IN HEIGHT. THE SHUTTERS ARE MADE OUT OF 18MM PLB, AND FITTED BY AUTO-CLOSING HINGES AND WITH SUITABLE LOCKING ARRANGEMENT. THE HANDLES USED ARE OF 75MM WITH SS FINISH. ALL STORAGES ARE PROVIDED WITH SUITABLE LEVELLERS TO CATER FOR FLOOR UNDULATIONS. AS PER THE CATALOGUE AND SAMPLES APPROVED BY THE ENGINEER-IN -CHARGE

RECEPTION TABLE: MADE WITH 25MM PLY WITH 1MM LAMINATE & 1MM ACRYLIC FINISH WITH ALL EXPOSED SURFACES FINISHED WITH 2MM EDGEBAND IN 3 PIECE: SIZE: 1500X 600X 1200 MM AS PER THE CATALOGUE AND SAMPLES APPROVED BY THE ENGINEER-IN -CHARGE

HIGH BACK CHAIR: MESH CHAIR. WITH HEADREST, AC 60 MESH, FABRIC UPHOLSTERED CUSHION SEAT, SINGLE LOCK SYNCHRO MECHANISM, ADJUSTABLE LUMBAR SUPPORT, ONE WAY ADJUSTABLE ARMS (HEIGHT), NYLON BASEAS PER THE CATALOGUE AND SAMPLES APPROVED BY THE ENGINEER-IN -CHARGE

MID BACK CHAIR: MESH CHAIR, AC 60 MESH, FABRIC UPHOLSTERED CUSHION SEAT, SINGLE LOCK SYNCHRO MECHANISM, ADJUSTABLE LUMBAR SUPPORT, ONE WAY ADJUSTABLE ARMS (HEIGHT), NYLON BASE AS PER THE CATALOGUE AND SAMPLES APPROVED BY THE ENGINEER-IN -CHARGE

LOW BACK CHAIR: PP (BLACK) BACK MESH CHAIR, AN 70 MESH, FABRIC UPHOLSTERED CUSHION SEAT, CENTRE TILT MECHANISM, FIXED ARMS, NYLON BASE AS PER THE CATALOGUE AND SAMPLES APPROVED BY THE ENGINEER-IN -CHARGE

LOW BACK CHAIR (VISITOR): PP (BLACK) BACK MESH CHAIR, AN 70 MESH, FABRIC UPHOLSTERED CUSHION SEAT, CENTRE TILT MECHANISM, FIXED ARMS,POWDERCOATED 4 LEGS AS PER THE CATALOGUE AND SAMPLES APPROVED BY THE ENGINEER-IN -CHARGE

WAITING CHAIR ( 3 SEATER): THE HIGH QUALITY LEGS AND FRAME SUPPORTS ARE MADE FROM COLD ROLLED STEEL, A3 STEEL, NICKLING. SUPPORT BEAMS ARE HEAVY GAUGE RECTANGULAR TUBULAR STEEL AND ALLOW FOR EASY ATTACHMENT OF LEGS, SEAT FRAMES, AND ARMREST ALONG WITH BEAM. THE BEAM IS FINISHED USING PHOSPHATING FOR SURFACE AFTER POWDER COATING . BOTH ARMS AND LEGS ARE CHROME PLATED. HEIGHT ADJUSTMENT OF UP TO 20MM ON EACH LEG ALLOWS FOR EASY LEVELING. THE SEAT FRAME IS STEEL TUBE WELDED TO THE SEAT AND BACK. THE SEATS AND BACKS ARE ERGONOMICALLY DESIGNED IN PERFORATED STEEL PLATE WITH A SMALL HOLE PATTERN FORMED WITH CURVES FOR ADDED COMFORT AND ROUNDED CORNERS, SIZE : L 1720 X D 700 X H 800 MM, AS PER THE CATALOGUE AND SAMPLES APPROVED BY THE ENGINEER-IN -CHARGE

COT WITH BEDSHEET AND PILLOW : MANUFACTURING , SUPPLY & FIXING OF DIVAN COT WITH MATRESSES 1 PILLOWS,DIVAN COT SIZE:1950MM X 750 MM X 350MM MADE OF 25MM THICK PLB EXPOSE EDGES COVERED WITH 2MM PVC EDGEBANDING TAPE, 4''MATTRESSES WITH PILLOW,BOMBAY DYEING BEDSHEET AND PILLOW COVER.AS PER THE CATALOGUE AND SAMPLES APPROVED BY THE ENGINEER-IN -CHARGE

Transportation and Handling Charges

Supply and fixing of ISI 25mm outer dia heavy grade with IS:9537 part 3 rigid PVC pipe concealed in Roof Slabs with all required accessories including labour charges etc., complete but excluding GST. Makes : Sudhakar / Modi / VIP/Precision.

Supply and fixing of ISI 25mm outer dia heavy grade with IS:9537 part 3 rigid PVC pipe concealed in wall with all required accessories [like 'U' nails, Junction box, PVC Bends and Cement] including masonary work for light, fan, common, separate plug point and switch / power boards etc., including all labour charges etc., complete but excluding GST. Makes: Sudhakar / Modi / VIP/Precision.

Supply and fixing of ISI 25mm outer dia heavy grade with IS:9537 part 3 rigid PVC pipe concealed in underneeth the floor with all required accessories including masonary work and labour charges etc., complete but excluding GST. Makes: Sudhakar / Modi / VIP/Precision.

Wiring with 2 runs of 1.5 Sqmm HFFR PVC insulated 1100V grade as per IS:694/2010, IS 17048 specification for Copper cable in existing pipe with 6A / 10A 1 Way 1 Module Modular Switch control with suitable Module Hot Dip Galvanized modular type Metal Box covered with suitable Modular Cover Frame, with 3 Plate Jumbo Ceiling Rose including all labour charges etc., complete for light and bell points in Non Residential Buildings but excluding GST. Copper cable Make: RR kabel / sudhakar / Nakoda/KEI/Polycab. Modular Switch, Socket, Metal box & Cover frame Make: Legrand Lyncus/GM Four five/Gold medal curve/Anchor Roma plus Ceiling Rose Make: Gold Medal Olive / Million Zoom / Anchor Penta Cherry.

Wiring with 3 runs of 1.5 Sqmm HFFR PVC insulated 1100V grade as per IS:694/2010, IS 17048 specification for Copper cable in existing pipe with 6A / 10A 1 Way 1 Module Modular Switch control with suitable Module Hot Dip Galvanized modular type Metal Box covered with suitable Modular Cover Frame, with 3 Plate Jumbo Ceiling Rose including all labour charges etc., complete for Ceiling fan and exhaust fan points in Residential Buildings but excluding GST. Copper cable Make: RR kabel / sudhakar / Nakoda/KEI/Polycab. Modular Switch, Socket, Metal box & Cover frame Make: Legrand Lyncus/GM Four five/Gold medal curve/Anchor Roma plus Ceiling Rose Make: Gold Medal Olive / Million Zoom / Anchor Penta Cherry.

Wiring with 2 runs of 1.5 Sqmm HFFR PVC insulated 1100V grade as per IS:694/2010, IS 17048 specification for Copper cable in existing pipe with 6A / 10A 1 Way 1 Module Modular Switch control with suitable Module Hot Dip Galvanized modular type Metal Box covered with suitable Modular Cover Frame, with 3 Plate Jumbo Ceiling Rose including all labour charges etc., complete for light and bell points in Non-Residential Buildings for stair case points/Two way in Residential Buildings but excluding GST. Copper cable Make: RR kabel / sudhakar / Nakoda/KEI/Polycab. Modular Switch, Socket, Metal box & Cover frame Make: Legrand Lyncus/GM Four five/Gold medal curve/Anchor Roma plus Ceiling Rose Make: Gold Medal Olive / Million Zoom / Anchor Penta Cherry.

Supply and fixing of 6 / 10A 3/2 Pin 2 Module Modular Socket with shutter. with 6 / 10A 1 Way 1 Module Modular Switch control on a Common switch board with suitable Module Hot Dip Galvanized Modular Metal Box covered with suitable Modular Cover Frame with earth continuity including wire leads, earth connections along with all labour charges etc., complete but excluding GST. Modular Switch, Socket, Metal box & Cover frame Make: Legrand Lyncus/GM Four five/Gold medal curve/Anchor Roma plus

Supply and fixing of 20A 2 Module Modular Socket with shutter and 16A / 20A 1 Way 1 Module Modular Switch duly recessed in wall with 3 Module Hot Dip Galvanized Modular Metal Box size covered with 3 Modular Cover Frame including earth connections and all labour charges etc., complete but excluding GST. [Power plug] Modular Switch, Socket, Metal box & Cover frame Make: Legrand Lyncus/GM Four five/Gold medal curve/Anchor Roma plus

Supply and fixing of 10A 3/2 Pin 2 Module Modular Socket with shutter-2 Nos and 6A / 10A 1 Way 1 Module Modular Switch control-2Nos duly recessed in wall with suitable Module Hot Dip Galvanized Modular Metal Box size covered with suitable Modular Cover Frame including earth connections and all labour charges etc., complete but excluding GST. [2 Socket board - for Raw power] Modular Switch, Socket, metal box & Cover frame Make: Legrand Lyncus/GM Four five/Gold medal curve/Anchor Roma plus

Supply and fixing of 10A 3/2 Pin 2 Module Modular Socket with shutter-2 Nos and 6A / 10A 1 Way 1 Module Modular Switch control-2Nos duly recessed in wall with suitable Module Hot Dip Galvanized Modular Metal Box size covered with suitable Modular Cover Frame including earth connections and all labour charges etc., complete but excluding GST. [2 Socket board - for UPS power] Modular Switch, Socket, metal box & Cover frame Make: Legrand Lyncus/GM Four five/Gold medal curve/Anchor Roma plus

Supply and fixing of Cat 6 RJ-45 information outlets including single face plate on 2 moduler hot dip galvanized metal box including giving connections, cost of all accessories and labour charges etc., complete but excluding GST. I/O & single face plate Makes: D Link / AMP / Molex / Legrand / Krone.

Supply and fixing of Modular socket type Telephone jack with Connector on 2 modular hot dip galvanized metal box and 2 modular cover frame including giving connections, cost of all accessories and labour charges etc., complete but excluding GST. Telephone jack with Connector, cover frame & metal box Makes: Legrand Lyncus/GM Four five/Gold medal curve/Anchor Roma plus

Supply and run of 3 of 2.5 Sqmm HFFR PVC insulated 1100V grade as per IS:694 / 2010, IS 17048 specification for Copper cable in existing pipe for 2 runs of mains & 1 run of earth continuity inlcuding all labour charges etc., complete but excluding GST. Make: RR kabel / sudhakar / Nakoda/KEI/Polycab.

Supply and run of 3 of 4.0 Sqmm HFFR PVC insulated 1100V grade as per IS:694 / 2010, IS 17048 specification for Copper cable in existing pipe for 2 runs of mains & 1 run of earth continuity inlcuding all labour charges etc., complete but excluding GST. Make: RR kabel / sudhakar / Nakoda/KEI/Polycab.

Supply and run of 3 of 6.0 Sqmm HFFR PVC insulated 1100V grade as per IS:694 / 2010, IS 17048 specification for Copper cable in existing pipe for 2 runs of mains & 1 run of earth continuity inlcuding all labour charges etc., complete but excluding GST. Make: RR kabel / sudhakar / Nakoda/KEI/Polycab.

Supply and run of 5 of 10.0 Sqmm HFFR PVC insulated 1100V grade as per IS:694 / 2010, IS 17048 specification for Copper cable in existing pipe for 4 runs of mains & 1 run of earth continuity inlcuding all labour charges etc., complete but excluding GST. Make: RR kabel / sudhakar / Nakoda/KEI/Polycab.

Supply and run of LAN Cable cat - 6 UTP cable in existing PVC conduit including cost and conveyance of all materials and labour charges etc., complete but excluding GST. Makes: D Link / AMP / Molex / Legrand / Krone.

Supply and run of 2 Pair, 0.5mm telephone copper wire in existing PVC conduit including cost and conveyance of all materials and labour charges etc., complete but excluding GST. Makes: Delton / Surabi / Polycab.

Supply and installation of 6U 600 mm width x 500 mm depth UL certified wall mounting network rack with sheet steel revited metal frame, top and bottom cover with brush cable entry, confirming to following standards IEC 60529, EN 60529 (IP 20), IEC 62262 EN 62622 (IK08), DIN 41494, EIA 310, IEC 60927 including all accessories like horizontal PDU, metal cable manager, hardware packet and the cantilever shelf etc., complete but excluding GST. Makes : Vallrack (Legrand) / Netrack.

Supply and fixing of 24 Port 10 / 100 / 1000 Gigabit Unmanageable Ethernet switch including giving connections cost of all accessories and all labour charges etc., complete. Makes : TP Link / D link / Netfox.

Supply and fixing of batten holder / slanting holder in lieu of ceiling rose of light point complete with all connections and all labour charges without bulb (for new installation) but excluding GST. BH Make: Gold Medal Olive / Million Zoom / Anchor Penta Cherry.

Supply, Transportation of energy efficient fan, 1200 mm sweep, aluminium body, consuming 28 W, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) motor, class of insulation: B, 3 no's blades, 30 cm long down rod, 2 no's canopies, shackle'kit, copper winding, Power Factor greater than 0.90, Service Value (CMMAV) greater than 8.0, Air delivery minimum 235 CMM, 350 RPM (tolerance as per IS:374-2019), THD less than 10%. with remote or compatible to electronic step type regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75°C(max), insulation resistance more than 2 mega ohm, suitable for 230V, 50 HZ, single phase AC supply, earthing etc., including all standard accessories etc., complete but excluding GST. Makes : crompton / Havells / Orient.

Supply of 2 Module Modular type Electronic Fan Regulator with 2 Module Hot Dip Galvanized Modular Metal Box covered with 2 modular cover frame etc., complete but excluding GST. Make: Legrand Lyncus/GM Four five/Gold medal curve/Anchor Roma plus

Labour charges for fixing of Ceiling fan and regulator including transportation and giving connections with twin core wire etc., complete but excluding GST.

Supply of 9" (225mm +/ - 5%) Light duty exhaust fan with metal blades etc complete Makes : Crompton / Havells Ventilair-DB

Labour charges for fixing of BLDC Exhaust fan in wall with necessary connections etc., complete but excluding GST. (for hole already made available)

Supply and transportation of 20W +/- 10%, >/ 2000 lumens, 1200mm length LED retro tube light, housing made with alluminium anodised body, wide operating voltage with double side connection, PF≥0.9, Surge protection: > 2KV, THD<15%, with inbuilt driver and frosted cover CCT: 3000K - 6500K as desired by the department and as per IS specifications, minimum CRI≥80 etc., complete with 5 years warranty with BIS Certification.LUMINAIRE MAKE: Crompton /Havells / Osram/Wipro LED Make: : PHILIPS LUMILEDS / CREE / NICHIA / OSRAM.

Fixing of 20W LED tube light luminaire on wall / Ceiling with all accessories including giving connections and all labour charges etc., complete but excluding GST.

Supply and fixing of 8 Way SPN DB with IP 43 Protection as per IS:13032 and suitable for 6 Nos s.p outgoings and for 1 No Incomer with 100 A tinned copper busbar, neutral bar, earth bar and cable ties for cable management fulIY shrouded neutral bar J din bars and detachableg land plate etc.I complete with inter connections but excluding GST Incommer: 40A DP lsolator - INo. Outgoing: 6-32A SP MCB, IOkA ISI mark - 6 Nos DB Makes: ABB/C&S/ LK (L&T). Isolator Make:ABB/C&S/ LK (L&T). MCB Make:ABB/C&S/ LK (L&T).

Supply and fixing of 4 Way TPN DB Horizontal with IP 43 Protection as per IS:13032 and suitable for 12 Nos S.P. outgoings and for 1 No 4 pole Incomer (FP Isolator / MCB) with 100 A tinned copper busbar, neutral bar, earth bar and cable ties for cable management, fully shrouded neutral bar, profile blanking modules for unused MCB ways, din bars and detachable gland plate etc., complete with inter connections but excluding GST. Incommer: 40A FP Isolator - 1No. Outgoing: 6-32A SP MCB, 10kA ISI mark - 12 Nos. DB Makes: ABB/C&S/ LK (L&T). Isolator Make: ABB/Havells/ LK (L&T)/C&S. MCB Make: ABB/Havells/ LK (L&T)./C&S

Supply and fixing of 6 Way TPN DB Horizontal with IP 43 Protection as per IS:13032 and suitable for 18 Nos S.P. outgoings and for 1 No 4 pole Incomer (FP Isolator / MCB) with 100 A tinned copper busbar, neutral bar, earth bar and cable ties for cable management, fully shrouded neutral bar, profile blanking modules for unused MCB ways, din bars and detachable gland plate etc., complete with inter connections but excluding GST. Incommer: 63A FP Isolator - 1No. Outgoing: 6-32A SP MCB, 10kA ISI mark - 18 Nos. DB Makes: ABB/C&S/ LK (L&T). Isolator Make: ABB/C&S/ LK (L&T). MCB Make:ABB/C&S/ LK (L&T).

Supply of 4 Way VTPN DB with IP 43 Protection as per IS:13032 and suitable for accommodating TP / DP as out goings and 125A / 160A 4 pole MCCB as Incomer with 250A tinned copperbusbar, neutral bar, earth bar and cable ties for cable management, fully shrouded neutral bar,profile blanking modules for unused MCB ways, din bars and detachableg land plate etc., completewith interconnectionsb ut excluding GST. Incomrner: 125A 4 Pole MCCB, 25kA - 1 No. Outgoing: 63A IOKA TP MCB C/D Curve ISI - 2 Nos. 40A IOkA DP C/D Curve ISI - 4 Nos. DB Makes : ABB/C&S/ LK (L&T). MCC’B Make: C&S- Win break /LK (L&T) - D sine / Schneider NSNSX MCB Make: ABB/C&S/LK (L&T).

Supply of 16 Sqmm 4 Core XLPE insulated, 1100V grade armoured alluminium cable with ISI mark as per specification confirming to IS:7098 (Part - I) but excluding GST. Makes : Universal / Torrent / Polycab / Gloster.

Earth work excavation of Trench in hard ground soil, laying of U.G cables from 70 sqmm to 400 Sqmm for laying of Hume pipes and back filling of trench including cost and conveyance of materials and labour charges etc., complete but excluding GST.

Labour charges for run of U.G cable on wall / existing pipe with necessary fixing arrangments such as saddles, clamps,wooden separators etc., (as directed by departmental official) etc., complete but excluding GST.

Providing independent earthing for Important equipment with 40mm dia 'B' class 2.5m long G.I pipe and 19mm dia 'B' class G.I pipe of 0.3mtr. long connected with reducer providing G.I funnel with mesh enclosed in C.C/ brick massonry chamber of 450m x 450m x 400mm with R.C.C. Slab cover duly providing staggered holes filling with 20Kg Salt and 40Kg Charcoal or 40Kg bentonite powder from the bottom of the pipe giving earth connection from electrode through G.I strip of 40 x 6mm x 200mm length with all accessories and labour charges complete, as per IS specifications 732/1982 (Part II) but excluding GST.

Supply and Run of No.8 SWG G.I Wire including cost of all accessories and labour charges etc.complete.