COMPREHENSIVE MAINT OF B/R AND ALLIED SERVICES IN CERTAIN SQN UNDER GE (AF) TECH AREA AGRA

Amount

Demolition of brick work or stone/boulder masonary built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

M&L Brickwork with fly ash bricks straight or curved on plan exc 6 m mean radius built in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

Dismantling wall and ceiling boards ( fibre, pulp, insulation etc or insulation boards/ slabs/ blankets any thickness including cover filletts complete all as specified and directed by Engineer-in-Charge.

S&F asbestos cement building board 4mm thick of size 595x595mm with decorative finish fixed to GI powder coated snap grid frame work with screw in ceiling complete all as specified and directed.

M&L for GI powder coated snap grid frame work for false ceiling of approved (ISI marked) make fixed to galvanised iron steel angle grid 600x600mm size suspended system fixed to GI framed work with main runner (32x24x6.5)mm cross tee (27x24x2.5)mm and moulding (19x19)mm of approved make and section as specified in SSR Part II with suitable hook/fasteners and GI/aluminium suspenders not less than 4mm dia upto 1200mm length @ 1.00m C/C minimum. ceiling system is to be fixed in water level without any sag including ceiling cleats made out of GI flat iron 40x3mm size 60mm long and expansion hold fastner 12.5 mm dia 40mm long complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M & L for glazed ceramic coloured tiles joint free of size 350x250 x 7 /450x350x7mm (Ist quality/Premium quality), in vertical surfaces such as riser of steps, skirting, dado and pillar, over and including rendering 10mm thick plastering as bed or bedding layer in CM (1:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for non-skid coloured ceramic tiles (1st quality/ premium quality) 7 to 8mm thick, (square/rectangular) area of each tile exc 0 .11 Sqm but not exc 0.18Sqm as in floors set and jointed in neat cement slurry and pointed in coloured or white cement to match the colour of tiles as in floor over 10 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for 10 mm thick Vitrified ceramic tiles, light shade double charged (square/recangular) area of each tile n exceeding 0.36 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of 15 mm thick in CM (1:6) for laying floor finishes complete all as specified and directed.

M&L for Machine cut kota stone slab flooring 20-22mm thick, laid over cement screed base laid and jointed with and including 15mm thick screed bed in CM 1:6 laid jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing all complete as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and paving of any thickness (below or above ground) complete all as specified and directed.

M&L for 75mm thick PCC(1:3:6) type C2 using 40mm graded stone aggregate as in sub base of floor etc complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 ( 20mm graded stone agg) 50 mm thick as in floor,coping etc complete all as specified and directed.

M&L for 25 mm thick sand cushioning laid dry to the profile under interlocking block complete all as specified and as directed.

M&L for machine pressed precast concrete interlocking paver block of approved shape and size of 60mm thickness, with minimum compressive strength of 35N/sqmm (M-35 grade) without correction factor for chamfering, made in rubber moulds with 0.50mm thick scratch proof lacquer coating on top surface, with grey cement and pigment complete all as specified and directed.

M&L 20-25mm thick plastic coated coloured chequered tiles, area of each tile exc 0.05sqm but n.exc 0.09sqm with and incl 20mm thick screed bed in CM (1:6) of approved colour and pointing with grey cement and pigment complete all as specified and directed.

M&L for outdoor Heavy duty coloured vitrified paving tiles , textured surfaces with high skid resistance , scratch resistance, impact resistant, joint free (edge cut) of size 600mm x 600mm x 8-10mm thick as in floor etc laid over and including 20mm thick screed bed or bedding layer in cement mortar 1:6, set and jointed in neat cement slurry and pointed with coloured cement to match the tiles complete all as specified and directed..

S&F in repair venetian blinds in double layers roller type of approved colour including all accessories, fitting/fixtures required for fixing the same in windows complete all as specified and directed.

M&L 20mm thick Granite telephonic black (of any type) tiles machine cut, in skirting/ dado laid over and including cement screed 15mm thick in CM (1:4) and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed.

Taking down cement plaster of any description on brick wall, ceiling etc. including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:6 on any faces of brick or concrete surfaces of walls & finishing the surface even and fair complete all as specified and directed at any location in any area incl repairing in patches at parapet, facing, fins, etc if any required at site for entire completion of work all as specified and directed

M&L for 15mm thick rendering in CM 1:4 on brick or concrete surface mixed with liquid water proofing compound @ 200 ml per bag cement or as per manufacturer's instructions , finished fair complete all as specified and directed at any location in any area incl repairing in patches at parapet, facing, fins and applying treatment for ATT on the same wall etc as per manufacturer's instructions, if any required at site for entire completion of work all as specified. Note : (i) Water proofing compound will be measured and paid seperately under respective item of Sch ‘A’. (ii) The Total cost for ATT (Anti Termite Treatment) will be included under this item of Sch ‘A’.

M & L for rendering 10mm thick in CM 1:4 on ceiling surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for providing & applying average 1mm thick of Birla/ JK wall care putty over prepared surface to achieve the surface even and smooth for painting, complete all as specified and as directed.

M&L for applying two or more coat of weather proof exterior emulsion paint in normal pattern/camouflage pattern by diluting of water (as per manufacturer direction) complete all as specified and directed by Engr-in-charge . Note :- Primer to be carried out through air less spray machine (Mechanical means) incl cleaning of existing windows/doors/floor etc.

M&L for preparation of new plastered surface of ceiling applying three coat of white wash by using mechanical device complete all as specified and as directed.

M&L for preparation of new surfaces of walls and applying two coat of oil bound distemper white or tinted by using mechanical device complete all as specified and as directed..

Dismantling of AC / fibre / steel sheets and the like (corrugated/semi corrugated/plain) in roof covering incl ridge complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550MPa as in roof covering/cladding to wall,fixed with self tapping screws as specified. Note:-work to be carried out upto 25.00m ht with necessary MS scaffolding including all other safety precautions.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 1.00mm thick of an colour having tensile strength of 550MPa as in roof covering/cladding/valley gutter to wall,fixed with self tapping screws as specified.

M&L in repair for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming Fe 410 -W(Gde-E- 250) quality-A all as specified and directed.

S&F in repair mild steel works as in wind ties for roof incl securing bolts; posts and struts in fencing incl cutting tops to shape as directed ,drilling holes,notching for wire,etc;flat iron fillets (for securing wire mesh etc) incl all necessary drilling,bolting or riveting etc and similar work conforming to Fe 410-0 or Fe 310-0 upto any height of bldg complete all as specified and directed.

M&L in repair Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing conforming Fe 410 -W (Gde-E- 250) quality-A complete all as specified and directed. NOTE:- work to be carried out upto 25.00m ht with necessary MS scaffolding including all other safety precautions.

M&L for mild steel work as in posts or struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc, flat iron fillets (for securing wire mesh etc) including all necessary bolting or riveting and spot welding etc and similar work conforming to Fe-290 Gde E-165

Taking down old fencing including RCC/steel post with mild steel flats & nut bolts of any description complete all as specified and directed.

Supply only chain link fencing mild steel galvanised fencing any size and type (size of mesh and dia of wire as directed by Engg-in-charge) all as specified.

Fixing only chain link fencing of any type fixed to RCC / steel post with mild steel flat & nut bolt etc,including necessary bolting complete all as specified and directed.

S&F Mild steel round bars 10mm dia and over as in strengthning bars for chain link fencing conforming to Fe-290 Gde E-165 complete all as specified and directed.

M&L for preparation of new steel surfaces of any description n.exc 10cm width or girth, not otherwise described and apply two coat of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10cm width or girth, not otherwise described for and apply two coat of synthetic enamel paint over one coat of red oxide primer complete complete all as specified and directed.

S&F in repairs Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples at height upto 15.0 mtr complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) indluding wooden beading from wooden/iron or aluminium frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and as directed.

S&F 3mm thick sheet glass ordinary quality for wooden/steel window and glazing with oil putty in squares or fixed with beads area in each pane area n.exc 0.50 sqm etc complete all as specified and as directed.

S&F in repair 300mm long stainless steel finished sliding door bolts, plate type, stove enameled black, with bright bolt not less than 12mm dia with and including minimum of 6 bolts and nuts, four on bolt plate and two on staple plate etc complete all as specified and as directed.

Taking down existing rolling shutter complete any type width and height not exceeding 3M in any position complete all as specified and as directed.

M&L for 1.25mm thick steel rolling shutter upto height 3M, without ball bearing as specified including guide channel, top covers anchoring rod, hasp and staple and other necessary accessories required to function the shutter including one shop coat of primer etc complete all as specified and as directed.

Taking down old steel/wooden windows with holdfast & making good surface to match with the existing and S&F windows/ ventilators fabricated from 0.6mm thick roll formed section made of galvanised steel powder coated (Base steel as per IS- 513 'D' quality) galvanised as per IS-277 with Zinc of 120 gm/sqm. Windows/ventilators having frame suitable for dual shutter i.e. inner and outer shutter with grill, glazed shutter with 4.0 mm thick glass, mesh shutter with 32 gauge stainless steel mesh, 6mm x 12mm flat iron with 10mm square bar MS grill and all fitting, fixtures accessories complete all as specified and shown in drawing no CEAF/STD-191/2014 Sheet 1/2 & 2/2 (4000 Series) NOTE: The quoted rate shall be deemed to be included the following:- (i) Glazed shutter with 4.00 mm thick glass, mesh shutter with 32 gauge stainless mesh and MS grill as per above mentioned drawing is deemed to be inclusive in the rate quoted. (ii) Glass, stainless steel mesh will be fixed to window by authorised rep of manufacturer of window only. (iii) making good of jambs in CM (1:4) and applying OBD in two coats including with putty complete.

S&F in repair aluminium (Die cast) body, door closer hydraulically regulated designation No-1, universal type, suitable for door shutters of weight not more than 35 kg complete all as specified and directed.

S&F Powder coated aluminium anodised frame for doors, with one or more rebates including joining cleat for fixing etc. complete all as specified and directed. (minimum thickness of powder coating 50 micron)

S&F powder coated aluminium anodised door shutters, aluminium section weighing 0.55 kg/ m including necessary aluminium anodised joining cleats, glazing clips, ruber neoprene packing, aluminium anodised handles 2 Nos in each door, aluminium anodised hinges 03 No's, aluminium anodised Tower bolt 02 No's, Powder coated aluminum snap beading, screws etc. complete all as specified and directed. (Minimum thickness of powder coating 50 micron)

S&F for Powder coated aluminium anodised window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary aluminium anodised joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.), hinges type B-21 100mm long (2 Nos.), suitable handle (1 No.) complete all as specified and directed (Minimum thickness of powder coating 50 micron)

S&F 12mm thick prelaminated particle board, interior grade, prelaminated both sides with decorative choice laminations for partition etc, complete all as specified and as directed.

S&F for aluminium anodized powder coated grills made out by using 6mm x 5 mm aluminium section having square gap of 50 mm thick with fixing rails of channels 12-15 mm etc complete all as shown in design Cat Part No -DG 101-DG-102 of jindal or equivlement as approved by GE.

S&F 5.5mm thick sheet glass black ordinary quality for Aluminium framed partition fixed with aluminium anodised cleat and rubber beading area in each pane area n.exc 2.00 sqm etc complete all as specified and directed

Taking down door chowkhat with shutter area n.exc 1.5 Sqm each (without taking off shutters from the frame) including making good of jambs with cement mortar 1:4 etc complete all as specified and as directed.

Taking down chowkhats or frames with shutters exc 1.5 Sqm but not exc 4 Sqm each (without taking off shutters from the frame) including making good of jambs with cement mortar 1:4 etc complete all as specified and as directed.

Taking out / dismantling of mud or existing roof treatment of, any thickness, including plastering and leaping and tiling/ peding of any description including disposal of removed/demolished soil/material exc 1.5 km but n.exc 5 km, depositing out side the MD land or where directed ny Engg-in-charge, complete all as specified and directed.

M&L for easing and repair of UPVC Doors of any size including taking down and refixing the same with necessary rendering and OBD required and replacement of all necessary hardware parts incl 3D hinges, mortice lock of both sides of door and also consider oiling /greasing where ever required completed all as specified and directed. Note :- Damages if any, caused due to poor workmanship shall be made good by the contractor at his own cost to match with the existing complete without any extra cost to the department.

M & L for roof treatment comprising of the followings:- (a) Providing PCC 1:2:4 (12.5mm graded)50mm thick with finished slope of 1:30 to RCC roof slab or as indicated in Drgs, testing of RCC slab for any leakage/seepage and making good before carrying out the water proofing treatment. (b). Providing average 15mm thick plaster in CM(Cement sand mortar) 1:3 mixed with water proofing compound when concrete is still green. (c). After the concrete is fully dried. It shall be cleaned free from dust and shall be painted with a coat of bituminous primer @ 0.40 liters/Sqm. (d). After primer, the entire roof surface shall be applied with hot blown bitumen grade 85/25 conforming to IS-702 @ 1.2 Kg/Sqm (e). Over hot bitumen, polymeric water proofing membrane consisting of 90 to 100 micron thick central core of HMHDPE film with standard weight not less than 3 Kg/Sqm shall be laid with 100mm side lap/end lap on prepared surfaces as of manufacture’s technical representation. (f). Pre casted machine pressed cement conc tiles 250x250x20-22mm/ 300x300x20-22mm confirming to IS : 1237:1980 laid over 15 mm thick cement mortar screed in 1:3. Joints shall be flushed pointed in CM 1:3.

M&L for zinc alloyed mortice handle lock 6 levers locking mechanism (white powder coated) for uPVC door with necessary screws etc completed all as specified and directed. Note :- Damages if any, caused due to poor workmanship shall be made good by the contractor at his own cost to match with the existing complete without any extra cost to the department.

M&L for stainless steel (SS-304 grade ) (white powder coated) friction 3-d hinges for uPVC door/Windows of any size with necessary screws etc completed all as specified and directed. Note :- Damages if any, caused due to poor workmanship shall be made good by the contractor at his own cost to match with the existing complete without any extra cost to the department.

Taking down existing door frame / shutters of area n.exc 60 Sqm by hydraulic/ mechanical cranes other tools & plant, necessary scaffolding required for lowering down the shutters carefully without causing damage to other components of hangars for repairing work straightning of frame angle and any section used in iron gates and re-fixing the door shutters in same position after necessary repairs complete all as specified and as directed. Note :- Damages if any, caused due to poor workmanship shall be made good by the contractor at his own cost to match with the existing complete without any extra cost to the department.

Supply only liquid water proofing compound complete all as specified and directed.

M/s M S Sharma and Co. (BID ID -3401117)

M/s Srijan Construction Company (BID ID -3390307)

GIRENDRA SINGH AND CO (BID ID -3393924)

C P Singh and Co (BID ID -3394153)

aman construction & general suppliers (BID ID -3393746)

m/s Narendra and company (BID ID -3394003)

Captainkomalchaharconstructions (BID ID -3393664)