Renovation of Canal Rest House at Hussainiwala Head

Amount

Dismantling brick or flagged stone flooring without concrete base.

Removing Doors and Windows (Steel or wood) with chowkhats by making recesses in walls when the wall is not to be dismantled

Doors of area 3 sqm and below

Windows of area 3 sqm and below

Scraping

white wash and colour wash

cement plaster

Plastering on underside of ceiling 10mm thick cement plaster 1:3

Repairs to plaster in patches of Area 2.5 sqm and under including cutting the patch in proper shape and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 Metres lead

With cement mortar 1:4 (1 cement: 4 sand) Taking area 2.5 sqm

Regrading terracing of mud plaster covered with tiles or bricks in cement by dismantling tiles or bricks, removing mud plaster, preparing the surface of mud plaster to proper, slope, relaying mud plaster Gobri leaping and tiles or bricks grouted in cement mortar 1:3 (1 cement and 3 fine sand) including replacing unserviceable tiles, or bricks with new over and disposal of unserviceable material to the dumping ground within 50 m lead

Top Khurra 0.6mx0.6m for rain water pipe in 25mm thick cement concrete 1:2:4 over 50.00 thick cement concrete 1:8:16

Bottom khurra on ground 1.2m 0.6m consisting of bricks on edge laid in cement mortar 1:3 over 7.5 cm cement concret 1:8:16 including 12.5mm thick cement plaster 1:3

Cement concrete 1:2:4 gola 10cm x 10cm concave quadrant along junction of roofs with parapet wall finished smooth, where specially specified.

Providing and Fixing ceiling consisting of 12.5mm thick Gypsum Board of any size G.I. Cradling hanged from the ceiling by means of G.I. hanger complete as per drawings,specifications and to the entire satisfaction of engineer-in- charge.

Screed of 50mm thick cement concrete 1:8:16 to be laid below the topping using mechanical mixer for mixing of material

Conglomerate floor 50mm thick cement concrete topping 1:2:4 using mechanical mixer for mixing of material

Fine dressed red stone (From Agra) flooring 40mm thick set in 12.5mm thick cement mortar 1:5 including jointing with cement mortar 1:2 with an admixture of pigment to match the shade of stone

Extra labour for projected nosing of any shape and design.

Supplying and fixing of Japani sheet frames (Chowkat) consisting of 18 gauge (1.25mm) thick steel sheet of the specified section (standard design latest), including iron lugs (hold fasts) iron hinges conforming to PWD specifications including bolts for fixing steps, lock notch provision for receiving tower bolts and finished, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame and cement concrete 1:2:4 for lugs complete to the satisfaction of Engineer-in-charge.

Door and window frame of size 113mmx60mmx with 35mm wide single rebate

Doors and windows frame of size 151mm x 60mm with 35 mm wide double rebate weighing 3.95 kg per meter.

Imported Teak Wood doors shutter windows shutter including hinges, screw and cords etc. Complete fixed in position

Panelled, glazed or glazed and panelled 35 mm Thick

Wire Gauge Imported teak wood door shutter without springs housed in chowkats 35 mm Thick

Factory manufactured flush door fixed in position iron hinges, etc (excluding the cost of any fittings other than specified above but including labour for fixing the same in position

35mm thick

Cost of aluminum fittings complete for doors, windows such as tower bolts, handles,Stoppers and screw etc. for these fittings (Excluding sliding bolt)

For shutter area above 0.50 sqm

Curtain rod 25mm dia aluminum pipe with brackets fixed in position including nails and screws etc. (Teak Wood)

Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :

Providing and fixing commercial plywood

Renewing glass panes with wooden fillets wherever necessary

Glass panes weighing 8.44 Kg/sqm

Preparation of plastered or concrete surface for painting (including sand papering the surface) using ready mixed cement based wall putty by applying two or more coats to get required finish

Distempering with Acrylic washable oil bound distemper (of approved manufacture) two or more coats over one priming coat to give an even shade

Wall painting with plastic emulsion paint of approved brand and manufacturer to give an even shade (two or more coats)

Preparation of plywood surface for painting including sand papering the surface and applying filling with approved quality fillers consisting of white lead, linseed oil, Varnish, and Chalk Mitti including finishing the surface to required finish complete

Applying pink primer or aluminum priming coat on wood work including preparation of surface knotting and stopping etc

Painting two or more coats excluding priming coat with synthetic enamel paint in all shades on wood work, metallic or plastered, concrete surface to give an even shade

Painting two or more coats with synthetic enamel paints in all shades on old wood work or metallic or plastered or concrete surface to give an even shade including rubbing down old paint.

Melamine polish two or more coats to give required finish including one coat of wood filler

Finishing walls with water soluble exterior paint such as snowcem, robbiacem etc. two or more coats to give an even shade

PUBLIC HEALTH

Dismantling Sanitary fixtures such as Eurpoean/ Indian/Orissa W.C., PVC / China ware cistern, Wash Hand Basin, Urinal Pot, Sinks and CP Fittings and disposal of dismantled material within a distance of 100 Mtr. complete in all respect as required by Engineer-in-Charge.

Eurpoean/Indian/Orissa W.C.,

PVC / China Ware Cistern

wash Hand Basin/Urinal Pot

Dismantling of wall tiles at any floor of the building, laid in cement mortar including scraping of cement plaster and disposal of malba at a suitable place within a distance of 100 Mtrs of the complex complete in all respect.

Dismantling of floor tiles at any floor of the building, laid in cement mortar including dismantling of cement concrete base and disposal of malba at a suitable place within a distance of 100 Mtrs of the complex complete in all respect.

CONCEALED IN WALL: Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes as per IS 15778 (ISI marked with the prior approval of Engineer-in-Charge), having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing including jointing of pipes & fittings, with one step CPVC solvent cement and testing of pipes complete as per direction of Engineer-in-Charge.

CPVC SDR 11 Pipe & fitting 16mmo/d

SDR 11 CPVC pipes & fittings 20mm o/d

CPVC SDR 11 Pipe & fitting 25mmo/d

Cutting holes upto 23cm square through B.B. in cement walls or stone masonary wall in cement for pipes, and making good the same & finishing according to existing finish where required.

Through wall 11.43 cm thick

Through wall 22.86 cm thick

Providing, fixing and jointing G.I Union Couplings(of approved make with the approval EIC) as per IS 1879 in G.I. Pipe lines complete in all respect.

20mm i/d G.I. Union

25mm i/d G.I. Union

Providing, fixing and jointing ISI Marked Gun-Metal peet valves (Heavy Pattern) as per IS 778 with hand wheels, on G.I. Pipe lines laid in the ground or inside buildings including all carriages complete.

20mm i/d Gun Metal peet valve heavy pattern.

25mm i/d Gun Metal peet valve heavy pattern.

Making connection with the existing G.I. branch main up to 40mm size pipe including cutting of existing pipe line, threading of pipe lines from both ends and fixing of G.I Tee etc. in the pipe line (including cost of G.I Tee) complete in all respects.

Providing & placing in position on terrace (at all floor levels) HDPE water storage tanks of approved make (to the approval of Engineer -in-charge) with cover with suitable locking arrangement and making necessary holes for inlet, outlet and over flo pipes but without fittings and base support for tank. Tripple Layer Tank

Providing and fixing in position G.I. Tank Nipple of approved make (to the approval of Engineer-in-charge) in PVC Water storage tanks complete in all respect.

G.I. tank nipple 25mm i/d

Providing and laying Rectified Porcelain floor tiles 400x400mm or more (thickness to be specified by the manufacturer) of premium quality conforming to IS:15622 of approved make in all colours laid on 20mm thick bed of Cement Mortar 1:4 (1 Cement : 4 Fine sand) for new flooring complete Rectified tiles have finished edges allowing them to be placed closer together for a narrower grout joint as opposed to other tiles and are more expensive. Unlike typical factory-edged tile, rectified tile is cut to size after the firing process. This process creates a precise, 90 degree angle edge and, as a result, can be laid with a tighter grout joint than un rectified tile. It gives a smooth, sophisticated and continuous look to the floor. Using a rectified tile allows you to place the tiles much closer together using tighter joint spacing. This makes the grout less visible as there is actually less grout used.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of size 310 x 450 mm as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:4 (1 cement: 4 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Chinaware Floor Mounted One Piece EWC rim less type with matching chinaware cistern 10 ltr. Capacity. (without cistern fitting) size 69x36x74 cm with P trap or S trap and seat cover complete in all respect.

Providing and fixing in position vitreous chinaware white lavatory suites of approved make (to the approval of Engineer-in-charge) consisting of C.P. brass waste 32mm dia with one C.P. brass pillar tap including Rack Bolt Screw Pair 115mm long complete in all respect.

Size 450mmx300mm

Providing and fixing in position C.P. brass bottle trap 32mm dia with 40 mm seal of approved make (to the approval of Engineer-incharge) complete in all respect

Providing and fixing in position stainless steel sinks of approved make (to the approval of Engineer-in-charge) 1mm thick,grade-304 (18/8) with waste coupling complete in all respect

Double bowl Sink without drain board Overall size 1330x515 bowl size 560x410x200mm

Providing and fixing in position C.P. brass soap dish of approved make (to the approval of Engineer-in-charge ) fixed into wall with rawl plugs and C.P brass screws complete in all respect.

Providing and fixing in position premium range C.P. Brass Fittings and accessories of approved make (to the approval of Engineer-in-charge ) complete in all respect. C.P. Brass fittings:

C.P. brass Bib cock with wall flange

C.P.brass 15mm Angular stop cock with Wall flange

C.P.brass 15mm Concealed stop cock with adjustable wall flange.

Providing and fixing in position premium range C.P. Brass Fittings and accessories of approved make (to the approval of Engineer-in-charge ) complete in all respect.C.P. Brass Accessories:

C.P. brass towel rail size 15mm dia 610mm long

C.P brass towel ring

C.P. brass toilet paper holder

C.P. brass Sink Cock with regularswinging spout and wall mounted

Providing and fixing jet spray with 2'-6" long PVC pipe. with C.P. Brass nut

Providing and fixing in position 32 mm dia G.I waste pipe embedded in wall upto floor level including cost of fittings complete as required by the Engineer-in-charge.

Providing & Fixing in position 5mm thick bevelled edge mirror of superior glass (of approved make) complete with 4mm thick hard board backing fixed in with rawl plugs 50mm, C.P. brass screws and washers and S/S Studs on top complete in all respect (as required by the Engineer-in- Charge)

Size 600mmx450mm

Providing & fixing in position PVC flexible tube connection of approved make (to the approval of Engineer-in-charge ) complete in all respect.

PVC tube connection of size 15 mm x 300 mm with C.P. Brass nut

Providing and fixing in position SS Grating with frame of approved make (to the approval of engineer in charge) complete in all respects.

C.P. Brass extension piece, 25mm longto 50mm long

ELECTRICAL

Wiring TV socket point (one module)

Replacement Of Wires, Cover Frames, Modular Switches, Concealed Metal Boxes And Other Accessories In The Existing Recessed Conduit Pipe Wiring System (With Modular Type Accessories)

Wiring fan point (Without fan box)

Wiring light point

Wiring call-bell point

Wiring 6Amp. wall socket point

Wiring 6Amp. Plug control comprising wall socket point

Wiring 16/20Amp. power plug control point

Wiring air conditioner supply terminal point recessed in wall etc., complete with powder coated/anodized concealed metal boxes required for suitable number of modules (Modular accessories) for having 25Amp. combined/ universal Socket (shuttered) and modular motor starter 25Amp. (2Module), covered with Frame Plate and other petty material etc. including the cost of above material, cutting and filling up of chases (with finishing the surface)

PVC INSULATED FR COPPER CONDUCTOR CABLES

Supply and erection of PVC insulated FR single core Unsheathed copper conductor cable (ISI marked) suitable upto 1100 volts grade confirm to IS:694/1990 left bare in pipe or casing of suitable size complete in all respect as desired by the Engineer-in-charge:-

Overall size 1.5sq.mm (Un-sheathed)

Overall size 4sq.mm (Un-sheathed)

Heavy Gauge PVC Conduit Pipe 20mm dia. (Flushed)

Heavy Gauge PVC Conduit Pipe 25mm dia. (Flushed)

Automatic Voltage Stablizer 2 KVA

Erection of Ceiling fan

Erection of 1X20/28/36/40W Box Type (LED/ Fluorescent) light fixture

Providing & applying heritage granual homogeneous wall finishing system from Bakelite Coating & Paints Pvt. Consisting of two component system of dry Granual (25 kg/pack) made of 92% silice particle, coated with fade resistant pigmants and 100% acrylic co-polymers bonding agent (5 ltr pack) with the applied thickness of coating beingbetween 0.8 to 1.2mm to be applied in single coat on a cured level smooth plastered, as per the shade combination approved and as per manufacturer specification, all complete inclusive of primer on the base.

NON SCHEDULE ITEMS

Supply of Koel Green Power Genertor - DG Set of 25 AMF Control Panel (KOEL GREEN BRAND 25 KVA DG SET)

Supply of split AC Hitachi 1.50 Ton/ 4500 kcal/hour high walls split AC 3 star (HITACHI DGS&D - RSC318HBDG)

Supply of LED 32" Samsung Smart Television Tv 32' LED Backlight LCD (UA32T4310AKXXL)

Supply of Refrigrator 300 ltr. Samsung 300 Litre 2 Star Frost Free Double Door Refrigerator (RT34A4622S8)

Supply of Bajaj Electric Geyser 25 Ltr Bajaj Electric Geyser 25 Litre 4 Star Water Heater

Supply of KENT RO Fully automatic with Cut off RO Potable Water Purification System (With maximum Input Water TDS 2000)

Samsung Domestic microwave oven 32 Litre capacity (MC32J7035CK)

Supply of orient 56" (1400 mm) ceiling Fans Orient electric Brushless Direct Current (BLDC) motor type ceiling fan 1400 mm

Sujata Centrifugal Juicer with power of 1000 watts and capacity of pulp container 1.4 Kg

LED luminaire Flood Light 60 Watts

Any Other Item

The Chak Sukar Coop L & C Society Ltd