WORK SERVICES FOR IMPROVEMENT TO SMQS AT GV CAMP AT 26ED, AF UNDER GE (AF) MARATHAHALLI

Amount

Dismantling of floor hearth or wall tiling including cement mortar bedding (including backing) removing servicable tiles to store and rubbish off the premises complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping, clean and washing down with water to remove dust, brushing neat cement slurry with 3.0kg of cement per sq. metre etc complete all as specified and directed.

M & L joint free coloured non skid ceramic tiles 7 to 8mm thick area of each tile exc 0.18 sqm but n.exc 0.38 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed CM 1:4, 15mm thick complete all as specified and as directed.

M & L joint free coloured non skid ceramic tiles 7 to 8mm thick area of each tile exc 0.18 sqm but n.exc 0.38 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including backing coat 10mm thick in CM 1:3 on vertical surface such as skirtings, dados risers to steps etc complete all as specified and directed.

M & L for Glazed ceramic tiles in vertical surface for toilet & Kitchen, 450mm x 350mm x 7 mm thick, dark coloured,on wall surfaces including designer pattern, set and jointed in neat cement slurry and pointed in white cement with pigment to match over 15 mm thick rendering in CM 1:3 all as specified and directed.

M & L joint free Non Skid ceramic tiles, 300mm x 300mm x 7mm thick, light coloured, in floor with 15 mm thick screed or bedding layer in cement mortar 1:4 for laying floor finishes, set and jointed in neat cement slurry and pointed in white cement with pigment to match all as specified and directed.

Taking down cement plaster on brick/stone wall and ceiling including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Dismantling of brickwork or stone/ boulder masonry, built in cement mortar/cement lime mortar including all quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M & L for pre cast cement concrete block masonry with solid block 10 cm thick in width (with plain or interlocking joints as directed) complete, in walls and set in cement mortar 1:6 of PCC 1:3:6 (Type C1) all as specified and as directed.

M & L for Dubbing out average 10mm thick on irregular face of walls in cement mortar 1:6 all as specified and as directed.

M&L, for rendering 10 mm thick in CM 1:3 on concrete surface of ceiling to be finished even and smooth surfaces without using extra cement complete all as specified and directed.

Refixing of wooden shutters in same opening exceeding 1Sq.m. and not exceeding 2 Sqm each complete all as specified and as directed. (Note :`refixing' includes taking down, easing and adjusting and also refixing builders hardware as required including renewal of unserviceable screws, etc.).

Dismantling of Stone slabs and tiles of any description or thickness in floors, aprons incl granite slab in kitchen platform laid, bedded and pointed in any mortar etc complete all as specified and directed.

M&L for Granite 18mm thick (of any type) work(table rubbed and polished)in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.

Providing edge moulding to 18-20mm thick Granite stone of counter vanities etc. including machine polishing to edge to give high gloss finish etc. complete

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for PCC 1:5:10 type E2 (using 40 mm graded stone aggregate), in as mass concrete/ sunken floors complete all as specified and directed.

M & L for 40mm thick cement concrete type B1 1:2:4 (using 20mm graded stone aggregate) in floor, finished even and smooth with out using extra cement complete all as specified and directed.

M & L for 75mm thick cement concrete type C1, 1:3:6 (using 20mm graded stone aggregate) in plinth protection, pavings, finished even and smooth with out using extra cement, incl making joints and filling gap with bitumen mastic complete all as specified and directed.

M & L Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid , set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed in CM 1:4, 20mm thick including rubbing and polishing of stone slab complete all as specified and directed

M&L for rubber moulded chequered cement concrete tiles 30cm x 30cm x 25mm thick, industrial type coloured, Pre polished,set, jointed and pointed in neat cement slurry with grey cement and pigments in floors incl. 20mm thick screed bedding layer in CM 1:4 complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces, mixed with water proofing liquid and finishing the surface even and fair without using extra cement, complete all as specified and directed. NOTE: Water proofing liquid shall be measured and paid separately under respective item of this schedule.

S&F in repairs Harrison rails (curtian rod), mild steel, chrominum plated with fixing brackets stops, roller etc complete all as specified and directed.

Taking down wooden/PVC shutters exceeding 1Sq.m. and not exceeding 2 Sqm each complete all as specified and as directed.

Taking down chowkhats or frames with shutters (without taking off shutter from the frame) not exceeding 1.5 Sqm each complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutter from the frame) wooden exc 1.5 sqm but not exceeding 4.0 Sqm each complete all as specified and directed.

M & L cutting holes to brick wall built in cement mortar exc half brick but n.exc one brick for inserting hold fasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B1 as required.

M & L cutting holes to stone wall built in cement mortar exc one brick but n.exc two bricks for inserting outlet trap and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B1 as required.

S&F for Second class hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed.

M & L for 35 mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars),II nd class hard wood, divided into squares with plain, chamfered or rounded, mitered and rebated sash bars in windows, ventilators, etc. are provided with stiles and rails as specified in SSR Part I, Section 8 clause 8.20 (b) any numbers complete all as specified and directed.

M & L 30mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides with lipping frame to match complete all as specified and directed by EIC.

S&F solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed by EIC.

S & F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail ; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading and joind together with solvent cement, suppling & fixing in the frame.

S & F powder coated aluminium (min thickness of powder coating 50 micron) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

Dismantling structural steel work including doors, gates, rolling shutters etc

S & F Anodised aluminium Sliding windows with frame powder coated aluminium, joining cleats for fixing etc. with aluminium anodised Glazed and skelton windows and shutters of glass, guage, sliding type(Glass and wire mesh measured and paid separately),Three track frame section not less than 0.98kg/Rm with out sash bars, using standard aluminium section shutter section weight not less than 0.55kg/Rm, joining cleats, glazing clips, rubber packing, anodised aluminium snap, beading screws, incl. anodised aluminium fittings such as handles, stainless steel adjustable lock, etc.incl. filling gap between window and wall filled with silicon sealant complete all as specified

S & F 18 mm thick lead free PVC solid celuka ply (density 600Kg/ Cum) plain white colour fixed with SS screws and solvent cement/ adhesive, with lipping as required over cut face surface etc to make frame work as in cupboard shelves, paritions, kitchen cabinets complete all as directed

S & F 18 /19 mm thick lead free PVC solid celuka ply (density 600Kg/Cum) of single side laminate of approved colour and other side plain white colour fixed with SS screws and solvent cement/ adhesive, matched colour lpping over cut face surface etc to make frame work as in cupboard shelves, partitions , kitchen cabinets including fixing of auto hinges, magnetic catches and SS handles (auto hinges, magnetic catches and SS handles shall be measured and paid seperately under supply only item) complete all as directed

M & L for Framed brackets of rolled mild steel angles or Tee sections, confirming to Fe 310-O, cut to shape, drilled and counter sunk for screws, including bending, welding as necessary, all as specified and directed.

Supply only CP mild steel auto hinges (heavy type - 150gm) four hole for cabinet shutters

Supply only 75mm SS handles

Supply only SS magnetic catches

S & F in repairs Kitchen plate rack made of stainless steel 0.8mm thick complete of size 760 x 610 X 254mm, duly assembled and fixed to the wall with wall screws/ fasteners all as specified and directed.

S & F in repairs stainless steel sinks with drainage board made of stainless steel 1.00mm thick stainless steel sheet of grade 304 for kitchen fixed with plugs, washers, overall size 915mm x 460mm with bowl size 405mm x 355mm x 178mm including chromium plated waste coupling of 32mm dia, including fixing cantilever brackets, PVC waste pipe 32mm dia and 600mm long (minimum), complete all as specified and directed.MAKE:- Cat No. SSSBSD-52 of Bluestar or techno-commercially equivalent model in Nirali / Anjali / Jayna / Diamond / M-Brand / Prince

S & F PVC waste pipe, 32 mm dia, 750mm long, suitable for Kitchen sink,fixed in repairs all as specified and directed.

Taking up or down 15mm bore steel tubing and connection including cleaing for refixing or removal to store all as specified and directed.

Taking up or down 20mm bore steel tubing and connection including cleaing for refixing or removal to store all as specified and directed.

S&F 20mm bore(OD) CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches/ walls and ceiling all as specified and directed.

S&F 25mm bore(OD) CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches/ walls and ceiling all as specified and directed.

S&F bib taps, brass chromium plated, fancy type, long body, screwed down, screwed for 15mm bore iron pipes or brass ferrule, fixed in repairs, all as specified and as directed.

S&F fancy type angle cock of brass chromium plated with long shank screwed for iron pipe and fixed (15mm minimum weight 90gms) 15mm dia fixed to iron pipe in repairs.

S&F in repairs Pillar taps brass chromium plated, fancy type, foam flow, screwed down high pressure screwed for iron pipe 15mm bore, all as specified and directed.

S&F in repairs 2 in-1 Bib taps, long shank with flange, 15mm size fixed in repairs all as specified and directed.

S&F Bib tap, with flange, 15mm size fixed in repairs all as specified and directed.

S&F fancy type concealed stop cock with flange of brass chromium plated with long shank screwed for iron pipe and fixed 15mm dia fixed to iron pipe in repairs.

S & F CP Swivel overhead shower (ABS chrome) with brass arm 150mm (with flange) for fixing to 15mm pipe all as specified and directed.

S&F PTMT towel rod 600mm long(min wt 190gms), fixed in repairs, all as specified and directed.

S & F glass assembly consists of 5.5mm thick sheet glass shelf 12cm wide fixed with and including chromium plated brass screws and wooden/plastic cleats with CP bracket, guard railing 60cm long, fixed in repairs, all as specified and directed.

S & F in repairs Vitreous china wash hand basin,vitreous china, white, flat back, of size 550x400mm, including pedestal with plug and porcelain stopper, brackets, waste coupling brass CP 32mm all as specified and directed.

S & F Towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gm all as specified and directed.

S & F in repairs waste coupling of PTMT (half or full threaded) Minimum weight 32mm-45gms) for 32mm dia all as specified and directed.

S & F Stainless steel gratings with frame, 127 mm dia, with hole for waste pipe connection as in repairs all as specified and directed.

S&F Vitreous China squatting pan, `Orrisa' pattern, size 580 x440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to drain (or out going pipe) and to flushing pipe, anti - syphonage pipe etc., including making good to floor complete fixed in repairs all as specified and directed.

S&F Vitreous china wash down water closet pan (pedestal pattern), white, complete with trap, fixed to floor with fixing bolts and seat cover, including connection to drain (or out going pipe) and to flushing pipe, anti - syphonage pipe etc., including making good to floor complete, fixed in repairs all as specified and directed.

S&F Plastic water closet seat cover any colour, closed pattern with flat bottom and mild steel chromium plated or aluminised hinging device fixed all as specified and directed. (Note: Seat cover make should be same as of WC make)

S&F for PVC connections 450mm long between ends with 2 Nos. brass nuts and washers, 15mm size, fixed in repairs, all as specified and directed.

S & F PVC 10 Ltr capacity flushing cistern white, inlet, ball valve, float and handle on existing brackets and jointing with existing flush pipe and making good to the disturbed surfaces including dismantling of unserviceable flushing cistern complete all as specified and directed.

S&F Health faucet, CP, with 1 metre flexible tube with wall hook, all as specified and directed.

S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, with 150mm long cover plate including provision of vulcanised rubber piece, fixed in repairs, all as specified and directed.

S & F Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.4 mm and fixed with stainless steel wire staple, all as specified and directed.

S & F in repairs Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.4 mm and fixed with stainless steel wire staple, all as specified and directed.

S & F 150 mm size aluminium barrel tower bolt of extruded section complete all as specified and directed.

S & F extruded aluminium handle 100mm long fabricated type anodised in repair all as specified and directed.

S & F extruded aluminium handles 150mm long fabricated type anodised all as specified and directed.

S&F for Aluminium, barrel tower bolt of extruded section, 100mm long in repair all as specified and directed.

S&F in Aluminium alloy, anodised, 300mm sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy fixed in repairs all as specified and directed.

M&L 100 mm butt hinges extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed type B 21 all as specified and as directed.

S&F 300 mm ordinary MS rat tail rod pattern spring including roller and roller plate in repairs complete all as specified and as directed.

Hacking out old broken glass of any thickness and description from wooden/ metal frames fixed with wooden beads/ putty all as specified and as directed.

Hacking out old broken glass of any thickness and description from wooden/ metal frames fixed with wooden beads/ putty all as specified and directed.

S&F for 4mm thick sheet glass, ordinary quality, glazing with wooden beads/ oil putty, in square not exceeding 0.50 Sqm in each pane complete all as specified and directed.

S&F for 4mm thick Figured glass, pin head type and glazing with oil putty in square not exceeding 0.50 Sqm in each pane all as specified and directed.

S & F pressed steel frames of size 105 x 60mm x 1.25 mm thick for door with one or more rebates, including necessary fixing lugs, hinges lock strike plate etc complete all as specified and directed.

M & L for cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) as in filling holdfasts frames complete all as specified and directed

S&F 110 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors or fixed to wall including necessary fixing cleats/ clamps, fixed in repairs complete all as specified and directed.

S&F 75 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors or fixed to wall including necessary fixing cleats/ clamps fixed in repairs complete all as specified and directed.

S&F 50 mm dia High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors etc complete all as specified and directed.

S&F PVC bend of 110 mm dia complete all as specified and directed.

S&F PVC bend of 110 mm dia with access door complete all as specified and directed.

S&F PVC bend of 75 mm dia complete all as specified and directed.

S&F PVC bend of 75 mm dia with access door complete all as specified and directed.

S & F PVC (SWR) branch piece, double(double Y) equal or un equal fixed to 110mm bore of pipes with access door complete all as specified and directed.

S & F PVC (SWR) vent cowl fixed to 110mm bore of pipes all as specified and as directed.

All as per item No. 94 here in before but 75mm bore complete.

S&F for PVC (SWR) 'P' trap suitable for 110mm/100mm bore of pipes all as specified and as directed.

M&L for PVC (SWR) floor trap 75mm dia, plain with grating including jointing with solvent cement complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:3 on fair faces of brick work or concrete surfaces, mixed with water proofing liquid and finishing the surface even and smooth without using extra cement, complete all as specified and directed. NOTE: Water proofing liquid shall be measured and paid separately under respective item of this schedule.

M&L for applying Nitroproof 600 Pa, minimum 0.8 dft over a priming coat of equivalent product on horizontal and vertical surfaces all as manufacturers instruction as in sunken slab surfaces. (Note :- Fill with water and check for dampness and seepage. In case the slightest indication of seepage/leakage is noticed, the same shall be rectified by the injection grouting to seal all cracks or application of polymer modified mortar FORSRO Nitrobond SBR or equilent product admixture the integral WPC or cementitious crystaline waterproofing compound in the effected area to seal all cracks and micro cracks if any including additional coat of Nitroproof 600 Pa. This shall be done by contractor at his own cost.

Removing by cutting up rooting plant/tree under surface of wall/ceiling including making good the damage portion with cement mortar 1:3 or concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) complete all as specified and directed (Note : Approx height of building 10m)

M & L Raking out joints/ pointing to Stone masonry or brick-work built in cement lime mortar in single detached joints for flashing, etc.all as specified and directed (Note : Approx height of building 10m)

M & L Flush pointing to block squared rubble masonry, coursed or uncoursed in CM 1:4 all as specified and directed (Note : Approx height of building 10m)

S & F Gate and shutter hooks and eyes 150mm mild steel in repairs complete all as specified and directed.

M & L for preparing previously untreated wood and wood based materials of any description over 10 cm width / girth and applying two coats of Synthetic Enamel paint over one coat of pink primer complete all as specified and directed.

M & L for One coat of white wash on old decorated surfaces of ceilings including necessary preparation of surfaces complete all as specified and directed.

M & L for three coat of white wash on newly plastered surfaces of ceilings including necessary preparation of surfaces complete all as specified and directed.

M & L for complete removal existing treatment on walls washing, rubbing down and stopping of existing treatment applying two coats oil bound emulsion distemper over a coat of primer over a coat of wall putty 1mm thick using rollers to match with existing surface complete all as specified and directed.

M & L for one coat of synthetic enamel paint on old painted steel surfaces of any description over 10cm width or girth including necessary preparation of surfaces all as specified and directed.

M & L for one coat of synthetic enamel paint on old painted wooden surfaces of any description over 10cm width or girth including necessary preparation of surfaces all as specified and directed.

M & L for two coats of synthetic enamel paint over a coat of red oxide primer on new steel surfaces of any description over 10 cm width or girth including necessary preparation of surfaces all as specified and as directed.

M & L for complete removal existing treatment on walls washing, rubbing down and stopping of existing treatment and applying two coats of acrylic emulsion paint on walls.

M & L for 10mm thick rendering in CM 1:6 finished even and fair on wall.

Preparing the newly plasterd surfaces of ceiling and applying two coat of cement based paint complete all as specified and directed.

M & L PVC (SWR) floor trap 75 mm dia of outlet, plain with grating including jointing with solvent cement fixed in repair all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for all as specified and directed.

M&L for reinforced cement concrete 1:2:4, type B1 (using 20mm graded stone aggregate) as in slab supported on wall, beam, roofs, landing, chajja, shelves etc all as specified and directed.

M&L for TMT bar 10 mm dia and over , cut to length bent to shape required, including cranking bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as directed.

M & L formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels for flat rough finished surfaces of concrete complete all as specified and directed.

M & L for formwork to soffits of suspended slabs such as roof slabs, floor slabs landing and similar work not exc 200 mm thick, with supports and rough finished surfaces of concrete complete all as specified and directed.

M & L for removing building materials etc. (other than spoil) to a distance exceeding 1.5 Km and not exceeding 5Km outside MD land, beyond the lead included in the rates, including loading,l unloading and stacking at the destination complete all as specified and directed.

S & F of 19mm thick plywood grade BWR type BB fixed with screws to fimber frame with lipping all round as in cupboard shelves

M & L for 30mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), IInd class hard wood, divided into squares with plain, chamfered or rounded, mitered and rebated sash bars in windows, ventilators, etc are provided with stiles and rails as specified in SSR Part - I, Section 8 clause 8.20 (b) any numbers all as specified and directed.

S&F powder anodised aluminium grill (anodised transparent or dyed to required shade according to IS:1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approval standard section and fixed to the existing window frame with C.P brass/ stainless steel screws @200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge

Taking down carefully copper/ aluminum point wiring (Light/Fan/Socket/power) complete including fittings and fixtures such as switches, ceiling roses, pendents regulators, sockets, light fittings etc., and making good the disturbed surfaces of walls/ floors etc complete all as specified and directed .

Taking down submain wiring of any size /description from wooden battens/PVC conduits from walls/floors/ceiling etc., complete and making good the disturbed area all as specified and directed.

Taking down DB's with MCB's / Isolator any rating and any size all as directed.

Dismantling and taking down fluorescent light fitting single /double tube any wattage /any size all as directed.

Taking down / refixing geyser any rating and any size kept in store with out damaging in safe custody and refixing same in position after repair work complete all as specified and directed.

Fixing only of LED light fittings 1x20 watt removed good working condition fittings kept in store with out damaging in safe custody and re-fixing the LED fittings after repair work complete all as specified and directed.

Removing and refixing after repair work of LED light fittings 1x10 watt, good working condition fittings kept in store under safe custody complete all as specified and directed.

Material and Labour for Point wiring complete with 1.5 sqmm single core PVC insulated FRLS cable 1100 volts grade with multi stranded copper conductor drawn through and including non metallic rigid medium grade PVC conduit with all accessories alongwith fixing arrangements in walls, roofs, floors, concealed/ surface wiring etc,or fixed in walls and including provision of 1.5 sqmm PVC insulated copper cable FRLS as earth continuity conductor connected to common earth dolly including metal flux boxes of suitable size and modular white plate with frame for mounting modular switches, sockets and regulators etc all as specified and directed for One light point controlled by one switch

All as per item No. 131 but one fan / exhaust fan point controlled by one switch.

All as per item No. 131 but one Bell / Buzzer point controlled by one switch.

All as per item No. 131 but one 5 amps socket point on independent board

All as per item No. 131 but one 5 amps socket point on same board with other switches

All as per item No. 131 but one light point controlled by two way switch.

Material and Labour for point wiring complete with 2.5 sqmm single core PVC insulated FRLS cable 1100 volts grade with multi stranded copper conductor drawn through and including non metallic rigid medium grade PVC conduit with all accessories alongwith fixing arrangement in walls, roofs, floors, concealed/ surface wiring etc or fixed in wall and including provision of 2.5 sqmm PVC insulated copper cable FRLS as earth continuity conductor connected to common earth dolly including metal flux boxes of suitable size and modular white plate with frame for mounting modular switches, sockets and regulators etc all as specified and directed for one 15 amps socket point on independent board.

Supply and fixing modular switch 06 Amps 1 module complete all as specified and directed.

Supply and fixing modular switch 2 way 6 amps 1 module complete all as specified and directed.

S & F modular socket 06 Amps 2/3 pin combined 2 module complete all as specified and directed.

S & F modular socket 16 Amps 2/3 pin combined 2 module complete all as specified and directed.

Supply and fixing modular switch 16 Amps 1 module complete all as specified and directed.

Supply and fix ceiling rose surface PVC / polycarbonate isolated body with three terminals all as specified and directed.

Supply and fix modular bell push 6 Amps 230 volts complete all as specified and directed.

Supply and fix Call bell 230 volts single pole A/C fancy type Ding Dong bell complete all as specified and directed.

Supply and fixing LED PC batten light fitting of 4 feet 20 watt, with energy efficient LED and integrated electronic driver of 20W fitting including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fixing LED light fitting of 2 feet 10 watt, with energy efficient LED and integrated electronic driver of 10W fitting including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fixing sheet metal enclosure MCB DB SPN 8 ways double door type with suitable bus bar complete all as specified and directed.

Supply and fix MCB single pole 5 to 32 Amps 230 volts 10 KA rupturing capacity

Supply and fix MCB single pole and neutral 5 to 32 Amps 230 volts 10 KA rupturing capacity

Supply and fix MCB Triple pole and neutral 40 to 63 Amps 230 volts 10 KA rupturing capacity

M&L Sub main wiring with two runs of single core PVC FRLS insulated cable with copper conductor multistranded 1100 volts grade 4.0 sqmm drawn through and including with suitable size of PVC conduit and its accessories , concealed/ surface/ ceiling along with fixing arrangement etc including one run of 4.0 sqmm PVC insulated multistranded copper earth contuinuity conductor and connected to common earth dolly complete all as specified. (Note : Two runs of cable, one run of earth conductor and one run of conduit shall be one unit).

Supply and fixing ceiling fan complete incl anti suicidal down rods with blades, electronic regulator and accessories, 230 V, 1200mm sweep Min air delivery 210 CFM with service value 6.00 BEE, five star rated with brushless direct current motor (BLDC)

Supply and fixing "S" Hooks for ceiling fans hanging of size 1200 mm sweep making hole on roof for fixing "S" hooks of 10mm dia MS and making good for damaged surfaces all as specified.

Taking down ceiling fan/Exhaust fan, sealing the cable ends dismantling the fan blade kept in safe custody in store complete all as specified.

Supply and fixing exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers.

M & L for earthing complete with galvanized steel earth plate electrode 600X600X6mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.5M below normal ground level connected to GI earth lead wire 4.0mmdia by means of nuts, bolts, check nuts and washer of GI steel and connecting to testing point including provision of test point and all as shown in electrical plate No. 3 of SSR Pt I. The work is inclusive of necessary earth work and PCC chamber in type B1 (1:2:4) with 8 CTD bar reinforcement both ways at 140 mm bent to centre complete including 15 mm GI tube for funnel and 20 mm for earth wire drawn through complete all as directed by Engr-in-Charge. (Note : Earth lead wire upto 7.5m shall be deemed included in the item and Earthwork is deemed included in the item)

Supply and fixing GI earth wire 4.00 mm dia for interconnecting of earth electrodes complete all as specified and directed.

Supply & fix exhaust fan made of study Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, copper winding of 250mm sweep complete all as specified and directed. (Make : Bajaj/ CG/ Philips/ Havells)

Taking down/ up labour for cutting and taking out the damaged/ corroded portion of GI Pipe 25mm dia, threading and joining pipe long/ short piece and connected accessories, arresting the leakage complete all as specified and directed.

Supply and fixing in repairs Galvanised iron pipes, 25mm bore, medium grade, with all fittings and connections, laid in floors or trenches/ fixed on walls/ ceilings and testing including making holes/ chases in walls and making good complete all as specified and as directed.

Supply and fixing in repairs Gun metal gate valve with iron wheel head ISI marked screwed both ends complete for 25mm dia iron pipes complete all as specified and as directed by Engr-in-Charge.

Excavation in trenches in Soft/ Loose soil not exceeding 1.5metre wide and not exceeding 1.5m deep for laying of pipe etc, getting out and forming bottom surface to required gradient complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in any type of soils complete all as specified and directed.

Removing excavated surplus soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point all as specified.

UNITED TECHNO PROJECTS PVT LTD

M Mohan Babu