SPL REPAIR TO BLDG NO P 45 QTR BLOCK OF 04 X QTRS JCO OR MD ACCN OF 367 COY ASC SUP TYPE D PANITOLA UNDER GE DINJAN

Amount

Taking down carefully unserviceable aluminium/copper point wiring (light, fan, socket or power) complete, including unserviceable fitting such as switches, ceiling roses, pendants, regulators, sockets, etc and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

Taking down unserviceable sub-main wiring any type with rigid steel conduits/PVC Conduits/PVC casing-caping complete all as specified and directed.

M&L point wiring with 1.5 Sqmm (nominal area), PVC insulated FRLSH, multistranded, single core, sheathed, copper conductor cables drawn through concealed PVC conduit not less than 20mm dia with all fittings and accessories (like Tee, bend etc.) complete for Phase, neutral and earth wire connecting to common earth point including steel terminal box made out of 1.2mm thick MS concealed in walls for housing switches, sockets, regulators, etc all as specified and as directed.

All as per item No above but one 5 Amps, 3/5 pin socket outlet on the same board with other switches complete all as specified and directed.

All as per item No above but for one 3/5 pin Switch socket combination, 5 Amps on Independent board complete all as specified and directed.

All as per item No. here-in-before but wiring with cables of size 2.5 sqmm & cables of size 2.5 sqmm as continuous earth wire for one 15 Amps switch socket combination on Independent board complete all as specified and directed.

M & L for Sub main wiring with two runs of 4 sqmm single core cable FRLSH PVC insulated, multistranded, unsheathed, copper conductor cables 1100 Volts grade drawn through concealed PVC conduit not less than 20mm dia with all fittings and accessories (like Tee, bend etc.)etc including 4 sqmm (nominal area) single core, FRLS PVC insulated, multistranded, unsheathed, copper conductor as earth wire and duly connected to common earth point complete all as specified and as directed by Engineer-in-charge. (Note : (a) PVC Conduits/Casing-caping, two run cables and one run of earth wire will be measured as one length. (b) All incoming and outgoing cable shall be connected by using proper lugs & sockets.)

S&F switch piano, 5 Amp single pole, flush type one way 230 volts complete all as specified and directed.

S & F Bell push, flush type, 5 Amps 230 Volts, complete all as specified and directed.

S & F Socket outlet, 2 in 1, 3 pin, 5 Amps, flush type complete all as specified and directed.

S&F Switch socket combination, 2 in 1, 5 Amps,flush type, 240 volt complete all as specified & directed.

S&F Switch socket combination, 5A/16A, 5 in 1, 240 volts, flush type complete all as specified & directed.

S & F call bell / Buzzer, Ding Dong AC. 230 volts, single pole all as specified and directed.

S & F lamp holder, insulated body with back plate suitable for batten fittings all as specified and directed.

S & F Ceiling rose, 3 phase/PVC/polycarbonate, isolated body all as specified and directed.

S&F in repair Stepped type electronic fan regulator flush type 230 volt 5 speed control and connecting up and fix position , complete all as specified & directed Make : ANCHOR/Legrand/Havells or Equivalent.

S & F new 18/20 W surface and wall mounted LED batten with polycarbonate housing and integrated driver all as specified and directed. (Make: Havells, Cat No. LUMILINENEOBS20WLED865SPCWH or equivalent make as per list of manufacturer

S&F 40 watt LED street light fitting in alminium PDC housing, toughened glass cover with lP65 protection including GI bracket 32 mm Dia nut, bolt, clamp and connection by 2.5 Sqmm wire complete all as specified & directed. Make: Bajaj/Havells

S&F 10W,LED, Energy saving new generation bulk head luminaire with opal diffuser including lamp including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed. Havells Cat part no- RUGBYGENXFTS10WLED865SSYMBOPC, Make: HPL/ Havells/ Bajaj/Phillips or equivalent as specified and directed.

Taking down unserviceable main switches, DBs, bus bars chambers including all fittings and fixtures such as MCBs, isolator, etc and removing from site complete all as specified and directed.

S & F Factory made board distribution (DB) Double Door in sheet steel enclosure with common bus bar at incomming end, TPN, 4 way, 240 Volts , 200 amps suitable for housing MCBs complete all as specified and directed.

S & F Factory made board distribution (DB) Double Door in sheet steel enclosure with common bus bar at incomming end, SPN, 8 way, 240 Volts , 200 amps suitable for housing MCBs complete all as specified and directed.

S & F MCB, TPN, 240 Volts, 63 Amps, 'C' Series, 10KA capacity complete all as specified and directed. (Make: hpl/Legrand, or equivalent make as per list of manufacturer)

S & F MCB, SPN, 240 Volts, 6 to 32 Amps, 'C' Series, 10KA capacity complete all as specified and directed. (Make: hpl/Legrand, or equivalent make as per list of manufacturer)

S & F MCB, 'C' Series, SP, 240 Volts, 5 to 32 Amps, 'C' Series, 10KA capacity complete all as specified and directed. (Make: Legrand, Cat No. 408587 to 408595 or equivalent make as per list of manufacturer)

S&F PVC rectangular block for mounting, switches, sockets, fan regulator etc. with 3 mm thick plastic laminated sheet cover of size 350 x 300 x 50 mm deep, including taking down old unserviceable one complete all as specified and directed.

M & L Earthing complete with GI earth plate electrode 600 mm x 600mm x 6 mm thick burried directly in ground vertically to a depth not less than 2.25 m below ground level with the top edge of earth plate at depth not less than 1.5 m below ground level connected to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers protected by 15mm bore light grade GI pipe, funnel with 20mm bore GI medium grade pipe for watering, wire mesh, including concrete pit in PCC (1:3:6) type C-1, pre-cast RCC 1:2:4 type B-1 cover slab of size 350x350x50mm reinforced with 8mm dia TMT steel bars @15cm centre to centre in both direction and 10mm dia MS handle of suitable size, charcoal or coke and salt in alternative layers,necessary earth work in soft/loose soil all as shown in Electrical Plate No 3 of MES Schedule Part I and testing complete inclduing taking down old one/ dismantling complete all as specified and as directed.

Taking down and Refixing of Ceiling fan 1200 mm sweep 230 volt including hanging arrangement of fan under different roof after repair made out of heavy duty MS rod/flat hook etc making connection by using 3 core 1 Sqmm flexible wire complete. Note- (1) GI Pipe for hanging of ceiling fan measured under relevent item of sch A.

Taking down and Refixing of existing water heater 25 Ltr using heavy duty grouting bolts 04 nos and making good the disturb surface matching with existing surface complete all as specified and directed.

Supply and fixing 9W LED Retrofit lamps Code: 9W NEO LED LAMP B22 6500K of make Surya or equivalent in Wipro/C&S/GE/Philips/Havells complete including taking down old unsv fittings.

S&F street light bracket fabricated out of GI Tubing light grade 32 mm bore Bend to the shape as directed and of length 1.5 mtr complete with mounting MS clamp of flat iron size 40X5mm of suitable length 02 pairs incl nut bolts etc of suitable size, including taking down old corroded one all as specified and directed.

Excavating in trenches n.exc 1.5 mtrs wide and n.exc 1.5 mtr in depth for for laying of cables,foundation etc and getting out in soft/loose soil complete all as specified and directed.

Supply and Laying well burnt bricks, sub class 'B' bricks laid breath wise along length of cable in trenches for cable protection laid for UG cable protection all as specified.

Material and labour for sand cushioning with clean dry sand in trenches for cable protection complete all as specified and as directed.(Note: Thickness after punning down shall be measured for payment)

Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25 cm thick in soft/loose soil complete all as specified and as directed.

Removing excavated materials n.exc 50 mtrs and depositing where directed at a level n.exc 1.5 mtr above the starting point in soil, complete all as specified and as directed.

Supply and lay cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 4 core including taking out of old unserviceable cable as specified and directed

M&L for steel water tubing of size 40 mm bore galvanised, medium grade with all fittings, laid in trenches or under road etc including taking down old one complete all as specified and directed

All as item above but of size 25mm bore

S&F Gun metal,globe or gate valves, with iron wheel, screwed both ends for iron pipe of size 40 mm dia.

S&F Gun metal,globe or gate valves, with iron wheel, screwed both ends for iron pipe of size 25 mm dia.

S & F in repairs, 32 mm bore, steel tubes, galvanised, light grade with all fittings and fixtures complete fixed to walls, ceilings, pole using suitable clamp/holder bat complete all as specified and directed.

M&L construction of brick masonry valve chamber of size 400mm x 400mm x 400mm (Internal dimension) with PCC 1:3:6 foundation 150mm thick, brick work 23cm thick built in CM 1:6, PCC 1:3:6 coping 50 mm thick, plastering 15mm thick in CM 1:4 to all internal and exposed surfaces including excavation earth work in any type of soil, MS sheet cover 3mm thick fixed with angel iron frame 30x30x4 mm including hinges of size 125mm with locking arrangement embedded in PCC and painting ot MS cover with two coats of synthetic enamel paint over one coat of red oxide primer etc complete all as specified and directed.

Dismantling of Asbestos cement (corrugated or semi corrugated ) sheets in roof covering.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and as directed.

S&F Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.5mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding/ridges etc , fixed with self tapping screws as specified and as directed.

Dismantling timber scantlings 40 Sq. cm and over in section and in any position in unframed work as directed.

M&L 2nd class hardwood, scantlings, wrought, timber fixed, complete as specified and directed.

M&L preparation of new wooden surface any description not otherwise described and exc 10cm width or girth applying two coats of synthetic enamel paint over a coat of pink primer including anty termite treatment as specified and as directed .

S & F roof/bottom plates with sleeve pieces riveted or welded thereto, and similar roof and ceiling connections all as specified and as directed.

S & F for rolled mild steel work in roof trusses (framed ), trussed, purlins crane gantries ,Post, rafts and fastening and heavy brackets framming (beams tee,angle channel and or flat sections) including distance pieces, cleat nut bolts etc quality confirming to Fe-290 (Gde E-165) all as specified and as directed.

M&L for preparation of old painted surface applying a coat of synthetic enamel paint on steel surface all as specified as directed.

M&L for preparation of new painted surface applying a coat of synthetic enamel paint on steel surface all as specified as directed.

Taking down cement plaster including racking out joints hacking for key, scrubbing down with water as specified.

M&L for rendering 15 mm thick on Fair face of External walls of brick surface in two layers (10 mm and 5 mm thick) in cement mortar in 1:4 using water proofing compound in top layer (Water proofing compound measured separately).

M&L for rendering 10 mm thick on brick wall other than fair face CM 1:6 finished even and smooth without using extra cement all as specified and as directed..

Supply only WPC of approved make all as specified and as directed.

M&L for two coat of distemper oil emulsion after preparation of new plastered surfaces of wall over a coat of clearcholle primar all as specified and as directed.

M&L for Two coat of cement base paint after preparation of new plastered surfaces over a coat of alkali resistant cement primar of walls all as specified and as directed.

M&L for two coat of distemper oil emulsion after preparation of old plastered surfaces of wall over a coat of clearcholle primar all as specified and as directed.

M&L for Two coat of cement base paint after preparation of old plastered surfaces over a coat of alkali resistant cement primar of walls all as specified

M&L for preparation of New decorated surface of wall and applying three coat of white wash all as specified and as directed.

M&L for preparation of old decorated surface of wall and applying two coat of white wash all as specified and as directed.

Dismantling wall and ceiling boards ( fibre , pulp, insulation etc ) or insulation boards/ slabs/ blankets , any thickness , including cover fillets.

M&L Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long, grid 605mm x 605mm and complete all as specified.

S & F for Anodised aluminium snap grid frame work for false ceiling all as specified and as directed.

M&L for 4mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws all as specified and as directed.

M&L for two coat of distemper oil emulsion over newly fixed false ceiling all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the permises.

M&L for providing non skid ceramic tiles (coloured) 7 to 8mm thick, area of each tile exc. 0.11 but not exc. 0.18 Sqm as in floor etc, including bed or bedding in 1:6 CM and set & joined in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all specified and as directed.

M&L for providing ceramic coloured tiles of size 350x250 x 7mm /450x350x7 mm thick) as in vetical surface over and including 10mm thick bedding in 1: 4 CM jointed & pointed in white or coloured cement to match the surface of tile as specified and as directed.

S & F anodised aluminium alloy harrison rails , mild steel , chromium plated with fixing brackets , stops, rollers etc.

Demolition of cement concrete (unreinforced) of any description and in any position not other wise specifically provided as specified and as directed.

M&L for providing 75mm thick PCC 1:3:6 type C2 (40mm graded aggregate) as in plinth protection and paving finishing the surface even and smooth without using extra cement.

M&L for 40 mm thick PCC 1:2:4 type B1 (using 20 mm graded stone agg) as in floor finish etc complete all as specified and directed.

S&F 35 mm thick, 2nd class hardwood plain, framed, panelled shutters (any number of panels) with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, complete as specified and as directed.

S&F 35mm thick skeliton/gauzed shutter open rebated and prepared to receive glass gauged etc(with sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24(a), supplied and fitted to chowkats.

S & F in repair for galvanised mild steel wire cloth 0.63mm nominal dia of wire and average width of aparture 1.00mm and fixed with stainless steel wire staples in window and door including wooden bids as fixed in repair as old door/window all as specified and as directed.

Taking down chowkats or frame n exc 1.5 sqm with shutter (with out taking off shutter from frame) all as specified and remooving from site all as specified and as directed.

S & F steel frames for doors (105 x 60 ) mm with one or more rebates including necessary fixing lugs , hinges , lock strike plate ,etc., complete ,as specified, supplied and fixed all as specified and as directed.

S&F 2nd class hard wood plain solid, straight chowkats and frames wrought,frame rebated on the solid,rounded or chamfered,put together with glue pinned at joints,supplied and fix all as specified and as directed.

S&F solid PVC door frames of size 50mm x 47mm made out of 5mm plain cover fillet colour PVC sheet reinforced with MS square tube for toilet as specified and as directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails, M.S frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either toside and as gap insert for top rail & bottom rail panelling of plain colour PVC sheet to be fitted in M.S frame welded/sealed to stiles and rails with suitable PVC sheet beading and jointed together with solvent cement. Supplying and fixing in the frame at site as specified of drawing.

Taking down window chowkats or frame exc 1.5 sqm but n exc 4 (without taking off shutters from the frame) all as specified and as directed remooving from site but with shutters with out takings off the shutters from the frame.

Taking down Shutters with chaukhat of any description n exc 1 sq. m each all as specified and as directed all as specified and as directed.

Refixing of Shutters of any description but exc 1 sq. m and n exc 2 sq. m each all as specified and as directed.

Supplied only 4.0 mm sheet glass , ordinary quality in squares any size 0.5 Sqm each pane all as specified and as directed.

S & F Galvanised mild steel wire cloth0.56mm nominal diaof wire and average width of aperture 1.18mm all as specified and as direected.

S&F 2nd class hardwood small fittings such as brackets of any type of door and window stopper including all necessary articles n.exc 2.00 cum each all specified.

S&F Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg Aluminium die cast body fixed In repair all as per specified and as directed.

M&L preparation of Old wooden surface any description not otherwise described and exc 10cm width or girth applying two coats of synthetic enamel paint over a coat of pink primer.

M&L for PCC 1:3:6 type C1 as in hold fast blocks incl. necessary form work all as specified.

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-16 all as speciefied and as directed.

S&F 100mm size butt hinges, Extruded aluminium alloy with galvanised mild steel hinge pin,anodised and fixed,type B-21 fixed in repair and brass/bronze pin is provided in lieu of mild steel hinge pin all as specified as directed.

S&F 125mm size aluminium handle cast type anodised complete.

S&F 200mm long aluminium anodised barrel tower bolt of extruded section conplete.

S & F Aluminium alloy ,anodised sliding door bolt with hasp , staple (bolt type) and fixing clips of sheet , cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast- aluminium alloy ,length of bolt of 250 mm all as specified and as directed.

S&F Soap dish, steel, Aproximate size 160x 160x9mm all as specified and directed.

S & F Chlorinated Polyethylene Chloride (CPVC) pipe 15 mm outside dia, SDR 11 (IS 15778) & plain CPVC SDR 11 including all special fittings (brass threaded elbow, tee, unions, etc.) polypropylenerandom fitting on wall/ceiling laying in floor complete all as specified.

Suppling and fixing CPVC Gate valve for 20 mm dia outer pipe complete all as specified and as directed.

Supply and Fix bib taps cast copper alloy, fancy type CP with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferule and fixed of size 15mm bore all as specified and as directed.

S&F 15mm stop / angle valves (concealed type), chromium plated, long sunk and cup, screwed both ends for iron pipe or for unions and fixed all as specified and as directed.

Supply and fix in repairs PVC flushing cistern 10 ltr capacity high level with inlet ball valve float chain and pull and brackets and flush pipe 32mm dia PVC pipe complete as specified and and as directed.

S&F in repair for vitreous china squatting pan 'Orissa' pattern, size 580x440mm white, with integral foot rests (excluding flushing cistern and flush pipe)including connection to trap, and to flushing pipe, anti-syphonage pipe etccomplete including making good to floors with PCC bedding (1:5:10) type E2 using 40mm nominal brick ballast and connection to trap with cement mortar all as specified, and making good to floor including demilition of PCC / Lime concrete bedding existing pan complete as in repairs all as specified.

S & F towel rails 60 cm long brass chromium plated 20mm dia with brackets fixed to walls in repairs all as specified and as directed.

S & F Shower rose fancy type chromium plated 125 mm size with swivel joints for fixing to 15 mm bore GI pipe or union all as specified and as directed.

S & F LDPE pipe as waste pipe 32 mm dia for wash basin all as specified and as directed.

S&F in repairs PVC (SWR) floor trap plain with grating incl jointing with solvent cement of 75mm dia all as specified and as directed.

S&F in repairs 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls all as specified and as directed.

S&F in repairs 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls

S&F in repairs 110mm PVC (SWR)pipes single socketed in any length with rubber ring joints,laid in trenches all as specified and as directed.

S&F in repairs 75mm PVC (SWR)pipes single socketed in any length with rubber ring joints,laid in trenches all as specified and as directed.

S&F for (SWR) junction single(single T)equal provided with access door 75mm bore all as specified and as directed.

S&F for (SWR) junction single(single T)equal provided with access door but of 110mm bore all as specified and as directed.

S&F PVC (SWR)bends any radius of 75mm bore all as specified and as directed.

S&F PVC (SWR)bends any radius of but of 110mm bore all as specified and as directed.

S&F PVC (SWR)vent cowl of 110mm bore all as specified and as directed.

M&L for RCC M25 (using 20 mm graded aggregates) in Chajjas any thickness above top of footing , roofs, landings, balconies, canopies, deck slabs and in shelves and the like all as specified and directed.

Demolition of brick work in cement mortar or cement lime mortar.

M&L brick work with sub class B bricks, straight or curved on plan exc 6 M mean radius, built in cement mortar 1:6.

Demolition of cement concrete(reinforced) of any description and in any position not otherwise specifically provided for.

M & L for RCC 1: 11/2 : 3 (nominal mix) type A1 20mm graded aggregate as in slabs including reinforcement bar as required staging for water tanks etc all as specified and as directed.

M/S N K SAI TRADING (BID ID -3136898)

NChetia and Sons Trading (BID ID -3139928)

CHETIA CONSTRUCTION (BID ID -3140742)

Bimal Trading Company (BID ID -3141546)

FREEZCON (BID ID -3141702)

M/s GANDHESWAR PHUKAN (BID ID -3141942)