Construction of MP Hall (G1) at JNV Araria (Bihar)

NAME OF WORK :- Construction of MP Hall at JNV, ARARIA (Bihar)

Sl. Estimated cost (in Rs.)

Details of work

No. DSR-2021 DSR-2022 N.S

1 Main Building-MP Hall

2 Plumbing Work 799,463.64 552880.00

3 Electrical Work 1,436,003.53 832,219.37

4 Fire Fightining work 764,936.71 272,329.00

6 Audio System 1,219,768.00

2 Development Work

1 Pathway 262,006.00

3 External water supply 39,284.35 40,000.00

5 External Sewerage line 434,528.06

6 External Electrification

(i) Supply & laying of cable 18,394.58 35,231.06

(ii) External lights - 70,537.32

(iii) Earthing & miscellaneous items 79,380.36 16,000.00

Total Amount (DSR+Non DSR) 41936154.72

Total Amount (DSR+Non DSR) 41936154.72

BILL OF QUANTITY FOR CIVIL WORKS

[ MULTIPURPOSE HALL]

S.N. DESCRIPTION OF ITEM DSR- AMOUNT DSR AMOUNT

QUANTITY UNIT RATES

2021 ITEM [M.R. ITEM]

1 Earth work in excavation by mechanical means (Hydraulic excavator) / manual

means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on

plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including

getting out the excavated soil and disposal of surplus excavated soil as directed,

within a lead of 50 m.

2 Filling available excavated earth (excluding rock) in trenches, plinth, sides of

foundations etc. in layers not exceeding 20cm in depth,consolidating each 2.25 94.760 CUM 29,411.61

deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m. 310.38

3 Supplying and filling in plinth with sand under floors, including watering,

ramming,consolidating and dressing complete. 2641.37

4 Excavating, supplying and filling of local earth (including royalty) by mechanical

transport upto a lead of 5km also including ramming and watering of the earth in

layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

Anti termite treatment

Supplying chemical emulsion in sealed containers including delivery as

5 Chlorpyriphos emulsifiable concentrate of 20% 2.34.1 294.20 Litre 245.54 72,237.87

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-

termite treatment (excluding the cost of chemical emulsion) :

6 Along external wall where the apron is not provided using chemical

emulsion @ 7.5 litres / sqm of the vertical surface of the substructure to

a depth of 300mm including excavation channel along the wall & rodding 2.35.1.1 98.032 Metre 3,870.30

etc. complete: With Chlorpyriphos/ Lindane E.C. 20% with 1%

concentration 39.48

Treatment of soil under existing floors using chemical emulsion @ one

litre per hole, 300 mm apart including drilling 12 mm diameter holes and

plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match

the existing floor:

7 With Chlorpyriphos/Lindane E.C. 20% with 1% concentration 2.35.3.1 491.200 Sqm 313.06 153,775.07

B Concrete Work

8 Providing and laying in position cement concrete of specified grade excluding the

cost of centering and shuttering - All work up to plinth level 1:5:10 (1 Cement : 5

coarse sand (zone-III) derived from 4.1.10 142.400 CUM 1,053,042.30

natural sources : 10 graded stone aggregate 40 mm

nominal size derived from natural sources) 7394.96

9 Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1

cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone 4.10 61.230 SQM 27,752.50

aggregate 12.5mm nominal size derived from natural sources) 453.25

10 Extra for providing and mixing water proofing material in cement concrete work in per 50kg

doses by weight of cement as per manufacturer's specification. cement 69.85

11 Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of

approved quality using 1.7kg per square metre on damp proof course after cleaning

the surface with brushes and finally with a piece of cloth lightly soaked in kerosene

12 Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse

sand (zone-III) derived from natural sources : 6 graded stone

aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed

of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted

with fine sand,including necessary excavation,levelling & dressing & finishing the

top smooth. 833.09

13 Brick edging in full brick width and half brick depth including excavation, refilling and

disposal of surplus earth lead upto 50 metres. 16.7.1 170.580 RM 37,421.84

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 219.38

C Reinforced Cement Concrete

14 Centering and shuttering including strutting, propping etc. and removal of form for

(a) Foundations, footings, bases of columns, etc. for mass concrete. 5.9.1 180.930 SQM 376.36 68,094.81

(b) Suspended floors, roofs, landings, balconies and access platform. 5.9.3 839.860 SQM 936.86 786,831.24

(c) Lintels, beams, plinth beams, girders, bressumers 5.9.5 1489.503 RM 743.51 1,107,460.38

(d) Columns,Pillars, Piers, Abutments, Posts and Struts. 5.9.6 776.079 SQM 982.93 762,831.33

(e) Edges of slabs and breaks in floors and walls Under 20 cm wide. 5.9.16.1 247.690 SQM 222.32 55,066.44

S.N. DESCRIPTION OF ITEM DSR- AMOUNT DSR AMOUNT

QUANTITY UNIT RATES

2021 ITEM [M.R. ITEM]

15 Extra for additional height in centering, shuttering where ever required with

adequate bracing, propping etc., including cost of de-shuttering and decentering at

all levels, over a height of 3.5 m, for every additional height of 1 metre or part

thereof (Plan area to be measured).

Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

16 Steel reinforcement for R.C.C. work including straightening, cutting, bending,

placing in position and binding all complete upto plinth level. Thermo-Mechanically 5.22.6 15620.000 KG 1,711,327.20

Treated bars of grade Fe-500D or more. 109.56

17 Steel reinforcement for R.C.C. work including straightening, cutting, bending,

placing in position and binding all complete above plinth level. Thermo- 5.22.A.6 27860.900 KG 3,052,440.20

Mechanically Treated bars of grade Fe-500 D or more. 109.56

18 Add for plaster drip course/ groove in plastered surface or moulding to R.C.C.

projections. 79.07

19 Providing and laying in position ready mixed or site batched design mix cement

concrete for reinforced cement concrete work; using coarse aggregate and fine

aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland

/Portland Slag cement, admixtures in

recommended proportions as per IS: 9103 to accelerate / retard setting of concrete,

to improve durability and workability without impairing strength; including pumping of

concrete to site of laying, curing, carriage for all leads; but excluding the cost of

centering, shuttering, finishing and reinforcement as per direction of the engineer-in- 5.33

charge; for the following grades of concrete.

Note: Extra cement up to 10% of the minimum specified cement content in design

mix shall be payable separately. In case the cement content in design mix is more

than 110% of the specified minimum cement content, the contractor shall have

discretion to either re-design the mix

or bear the cost of extra cement.

(I) All works upto plinth level 5.33.1

Concrete of M25 grade with minimum cement content of 330 kg /cum 5.33.1.1

Concrete of M30 grade with minimum cement content of 350 kg /cum 5.33.1.2

(iii) R.C.C. work in Columns 5.33.1.2 20.710 CUM 10786.13 223,380.75

(II) All works above plinth level upto floor V level 5.33.2

Concrete of M25 grade with minimum cement content of 330 kg /cum 5.33.2.1

Concrete of M30 grade with minimum cement content of 350 kg /cum 5.33.2.2

(iii) R.C.C. work in Columns 5.33.2.2 54.324 CUM 12805.65 695,654.13

D Masonry Work

20 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class

designation 7.5 in superstructure above plinth level up to floor V level.Cement 6.13.2 171.570 Sqm 213,474.26

mortar 1:4 (1 cement :4 coarse sand) 1244.24

21 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third

course of half brick masonry. 105.66

22 Brick work with non modular fly ash bricks conforming to IS:12894, class

designation 10 average compressive strength in superstructure above plinth level 6.34.2 313.620 CUM 2,942,316.98

up to floor V level in : Cement mortar 1:6 (1 cement : 6 coarse sand) 9381.79

23 Brick work with common burnt clay F.P.S. (non modular) bricks of class

designation 7.5 in foundation and plinth in: 6.1.2 104.880 CUM 853,466.24

Cement mortar 1:6 (1 cement : 6 coarse sand) 8137.55

Random rubble masonry with hard stone in foundation and plinth including levelling

24 up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone 7.1 -

aggregate 20 mm nominal size) upto plinth level with :

Cement mortar 1:6 (1 cement : 6 coarse sand) 7.1.1 54.70 CUM 8131.69 444,803.44

F Cladding Work

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and

prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias

and similar locations of required size, approved shade, colour and texture laid over

20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with

white cement, mixed with matching pigment, epoxy touch ups, including rubbing,

curing, moulding and polishing to edges to give high gloss finish etc. complete at all

S.N. DESCRIPTION OF ITEM DSR- AMOUNT DSR AMOUNT

QUANTITY UNIT RATES

2021 ITEM [M.R. ITEM]

26 Providing edge moulding to 18mm thick marble stone counters, Vanities etc.

including machine polishing to edge to give high gloss finish etc. complete as per

design approved by Engineer-in-Charge.

27 Extra for fixing marble /granite stone over and above corresponding basic item, in

facia and drops of width upto 150 mm with epoxy resin based adhesive including 8.4 79.50 RM 46,206.20

cleaning etc. complete. 581.21

28 Extra for providing opening of required size & shape for wash basins/ kitchen sink in

kitchen platform, vanity counters and similar location in marble/Granite/stone work

including necessary holes for pillar taps etc. including moulding, rubbing and

polishing of cut edges etc. complete. 987.70

29 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622

(thickness to be specified by the manufacturer), of approved make, in all colours,

shades except burgundy, bottle green, black of any size as approved by Engineer-in-

Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement

mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg 8.31 268.670 SQM 349,195.77

per sqm, including pointing in white cement mixed with pigment of matching shade

30 Providing and Fixing of Acoustical Wall Panel with square edges made of fibre

glass substrate 25mm thick, wrapped on the front side with an acoustically

transparent fabric as per the approved shade (Husk, Copper, Sangria, Sesame,

Coffee, Charcoal, Titanium, Flame, Peanut and Shell). The panel shall be classified

for Fire Class A, as per ASTM E-84. The Acoustical Wall Panel shall be of sizes

600x600mm (Nominal) or 600x1200mm (Nominal) and shall achieve an NRC of

0.85 (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz,

1000 Hz and 2000 Hz) with 50mm airgap as per ASTM C423 to be fixed to wall on a

framework of wooden battens and using Wall panel Impalers (supplied by the

manufacturer) or by using construction adhesives (as per the instructions laid down

by the manufacturer). The fibre glass substrate shall have a recycle content of 85%. MR sqm -

Properties of Tile Relevant Standards Base Material Fibre Glass

Panel Dimensions 600mm x 600/1200mm Panel Thickness 25mm

Panel Finish Acoustically transparent fabric as per the approved shade (Husk,

Copper, Sangria, Sesame, Coffee, Charcoal, Titanium, Flame, Peanut and Shell).

Fire Properties Class A ASTM E-84

Noise Reduction Co-efficient 0.85 ASTM C423 (Average value of Absorption

readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz)

31 Providing & fixing of 100% Natural Material- Magnesite (Hygroscopic & biologically

sound binding agent) bonded woodwool Panel planks of 600Mm*1200Mm *25Mm

thickness made out of wood wool fibre of width 1Mm Fiber thickness mixed with

Natural water & Magnesite (No-Cement) with open & smooth surface texture. A

Completly harmless Envirenment & Human Friendly & also a disposable or

recyclable Material & can last for long span in building interiors As it has long

lifespan & suitable for Indoor conditions with relative air humidity of upto 90%.

Magnesite protects the wood cells against ageing & fungal attack. To achive upto

NRC=1.00 it should be a clear gap of 200Mm from wall slab along with the backing

of Mineral of 50kg/m3. Edge Detail : AK 01 MR sqm -

Heradesign Woodwool - Acoustical Wall Mounting System Solutions- Ecologically

Material with high mechanical strength with Crash test of 90Km/H with Ball Impact

DIN18032 & EN13964 with flying colors & A sustainable material (PEFC & FSC

along with EPD Certified Acc. to EN ISO 14025 (AUB-Environmental Product

G Wood and PVC Work -

32 Providing and fixing panelling or panelling and glazing in panelled or

panelled and glazed shutters for doors, windows and clerestory windows (Area of

opening for panel inserts excluding portion inside grooves or rebates to be 9.7

measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm

Float glass panes 9.7.7

5.0 mm thick glass panes (weight not less than 12.50 kg/sqm). 9.7.7.2 33.150 SQM 2726.92 90,397.40

S.N. DESCRIPTION OF ITEM DSR- AMOUNT DSR AMOUNT

QUANTITY UNIT RATES

2021 ITEM [M.R. ITEM]

33 Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-

section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter

of 30 mm thickness. The laminate shall be moulded with fire resistant grade

unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm

thick and shall be filled with suitable wooden block in all the three legs. The frame 9.121 76.050 RM 65,304.14

shall be covered with fiber glass from all sides. M.S. stay shall be provided at the

bottom to steady

the frame. 858.70

34 30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door

shutter in different plain and wood finish made with fire

retardant grade unsaturated polyester resin, moulded to 3

mm thick FRP laminate all around, with suitable wooden

blocks inside at required places for fixing of fittings and

polyurethane foam (PUF)/Polystyrene foam to be used as 9.122.2 24.860 SQM 120,430.29

filler material throughout the hollow panel, casted

monolithically with testing parameters of F.R.P. laminate

conforming to table - 3 of IS: 14856, complete as per direction

of Engineer-in-charge. 4844.34

35 Providing and fixing factory made uPVC white colour casement/

Casement cum fixed glazed door comprising of uPVC multi-chambered

frame, sash and mullion (where ever required) extruded profiles duly

reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made

from roll forming process of required length (shape & size according to

uPVC profile), uPVC extruded glazing beads of appropriate dimension,

gasket, zinc alloy (white powder coated) 3D hinges and one handle on

each side of panels along with zinc plated mild steel multi point

lockinghaving transmission gear, cylinder with keeps and one side key,

G.I fasteners 100 x 8 mm size for fixing frame to finished wall and

necessary stainless steel screws, etc. Profile of frame & sash shall be

mitred cut and fusion welded at all corners, mullion (if required) shall be

also fusion welded including drilling of holes for fixing hardware's and 9.147C

water etc. After fixing frame the gap between frame and adjacent finished

wall shall be filled with weather proof silicon sealent over backer rod of

required size and of approved quality, all complete as per approved

drawing & direction of Engineer-in-Charge. (Single / double glass panes

and silicon sealent shall be paid separately). Variation in profile

in higher side shall be accepted but no extra payment on this account

Note: For uPVC frame, sash and mullion extruded profiles minus 5%

tolerance in dimension i.e. in depth & width of profile shall be acceptable.

Casement door with top hung ventilator with 3D and S.S.

friction hinges (400 x 19 x 1.9 mm) made of (big series)

frame 67 x 64 mm, sash 67 x 110 mm & mullion 67 x 80

mm all having wall thickness of 2.3 ±. 0.2 mm and

single glazing bead / double glazing bead of appropriate

dimension.(Area of door upto 2.50 sqm) 12774.12

36 Providing and fixing fire resistant door frame of section 50 x 60 mm on

horizontal side & 35 x 60 mm on vertical sides having built in rebate

made out of 1.6 mm thick GI sheet ( Zinc coating not less than

120gm/m²) suitable for mounting 120 min Fire Rated Glazed Door

Shutters. The frame shall be filled with Mineral wool Insulation having

density min 96Kg/m³ . The frame will have a provision of G.I. Anchor

fastners 14 nos ( 5 each on vertical style & 4 on horizontal style of size 9.161 42.60 RM 93,250.55

M10 x 80 ) suitable for fixing in the opening along with Factory made

Template for SS Ball Bearing Hinges of Size 100x89x3mm for fixing of

fire rated glazed shutter . The frame shall be finished with a approved fire

resistant primer or Powder coating of not less than 30 micron in desired

shade as per the directions of Engineer - in- charge . (Cost of SS ball

bearing hinges is excluded). 2188.98

S.N. DESCRIPTION OF ITEM DSR- AMOUNT DSR AMOUNT

QUANTITY UNIT RATES

2021 ITEM [M.R. ITEM]

37 Providing and fixing 60 mm thick glazed fire resistant door shutters of 120

min Fire Rating confirming to IS:3614 (Part II) or EN1634-1:1999,

tested and certified as per laboratory approved by Engineer-in-charge,

with suitable mounting on door frame, consisting of vertical styles, top rail

& side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60mm

made out of 1.6mm thick G.I. sheet (zinc coating not less than120gm/m²)

duly filled mineral wool insulation having density min 96 kg/m³ and fixing

with necessary stainless steel ball bearing hinges of size100x89x3mm of

approved make, including applying a coat of approved fire resistant

primer or powder coating not less than 30 micron etc all complete as per

direction of Engineer-in-charge (panelling to be paid for seperately).

38 Providing and fixing glazing in fire resistant door shutters, fixed panels &

partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc

coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x

38 mm SS screws at distance 75 mm from the edges and150 mm c/c ,

including applying a coat of approved fire resistant primer/powder coating

of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x

20 mm size etc complete in all respect as per NBC 2016, IS 16231 (Part

3):2016 and as per direction of Engineer-incharge with glass of required

thickness having 120 minutes of fire resistance both integrity & radiation

control (EW120) and minimum 20minutes of insulation (EI20). The 9.164 2.16 SQM 105,584.93

manufacturer have to give test report/certification of fire glass and the

glass should have the stamp showing the value of E, EW & EI. The glass

shall be tested in approved NABL accredited lab or by any other

accreditation body which operates in accordance with ISO/IEC 17011 and

accredits labs as per ISO/IEC 17025 for testing and calibration scopes

shall be eligible. The maximum glazing size shall not be

more than 1100x2200 mm (w x h) or 2.42 sqm.

Note: Rate of hardware items deemed to be include in above items. All

Hardware required as per approved shop drawing should pass European

certificate "CE" of conformity / UL with required fire ratings.

39 Providing and fixing bright /matt finished Stainless Steel handles of approved quality

& make with necessary screws etc all complete. (a) 125 mm. 122.77

40 Providing & fixing Stainless steel (grade SS-304 or higher) sliding door bolt/aldrop

of size 250x16mm on door shutter including all accessories as per direction of E/I M.R. 13.000 NOS 719.00 9,347.00

41 Providing and fixing Stainless steel (grade SS-304 or higher) tower bolt (barrel type)

with necessary screws etc. complete all work as per direction of E/I

42 Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by

providing weather silicon sealant over backer rod of approved quality as per

architectural drawings and direction of Engineer-in-charge complete.

Upto 5mm depth and 5 mm width 104.19

Steel work in built up tubular (round, square or rectangular hollow tubes

etc.) trusses etc., including cutting, hoisting, fixing in position and

applying a priming coat of approved steel primer, including welding and 10.16.1 2000.00 KG 378,620.00

bolted with special shaped washers etc. complete.

Hot finished welded type tubes 189.31

43 Designing, Providing, installing and fixing factory finished customed

design pregalvanized high tensile steel joists manufactured from G350 Z275

confirming to IS:277-1992, minimum coating of galvanizing 275 gm/sqm, minimum

yield stress 35 MPa & minimum tensile strength of 380 MPa placed 1.23 metre

apart to support the load of slab etc as per the design & directions of Engineer-in-

Charge. 172.88

44 Steel work welded in built up sections/ framed work, including cutting,

hoisting, fixing in position and applying a priming coat of approved steel

primer using structural steel etc. as required. In gratings, frames, guard 10.25.2 465.15 KG 80,898.89

bar, ladder, railings, brackets,

gates and similar works 173.92

45 Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes,

channels, plates etc., including welding, grinding, buffing, polishing and making

curvature (wherever required) and fitting the same with necessary stainless steel

nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless 10.28 1274.570 KG 953,735.24

steel dash fasteners , stainless steel bolts etc., of required size, on the top of the

floor or the side of waist slab with suitable arrangement as per approval of Engineer-

in-charge. 748.28

S.N. DESCRIPTION OF ITEM DSR- AMOUNT DSR AMOUNT

QUANTITY UNIT RATES

2021 ITEM [M.R. ITEM]

46 Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard,

jointed with neat cement slurry mixed with pigment to match the shade of tiles,

including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar

1:4 (1 cement: 4 coarse sand). Medium shade pigment using 50% white cement

Grey cement 1417.72

Marble stone flooring with 18 mm thick marble stone, as per sample

of marble approved by Engineer-in-charge, over 20 mm (average) thick base of

cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement

slurry, including rubbing and polishing complete with :

48 52 mm thick cement concrete flooring with concrete hardener topping, under layer

40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone

aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener

consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm 11.4 731.250 SQM 764,931.38

nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement

or as per manufacturer's specifications. This includes cost of cement slurry, but

excluding the cost of nosing of steps etc. complete. 1046.06

49 Cement plaster skirting up to 30 cm height, with cement mortar 1:3

(1 cement : 3 coarse sand), finished with a floating coat of neat cement.

50 Providing and laying rectified Glazed Ceramic floor tiles of size 300x300

mm or more (thickness to be specified by the manufacturer), of 1st quality

conforming to IS : 15622, of approved make, in all colours, shades, except White,

Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 11.40 85.080 SQM 127,389.43

4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing

the joints with white cement and matching pigments etc., complete.

51 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by

the manufacturer) with water absorption less than 0.08% and conforming to IS:

15622, of approved make, in all colours and shades, laid on 20mm thick cement

mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @

3.3kg/sqm including grouting the joints with white cement and matching pigments

etc., complete. (a) Size of Tile 600x600 mm 1731.40

52 Providing and laying Vitrified tiles in floor in different sizes

(thickness to be specified by the manufacturer) with water

absorption less than 0.08% and conforming to IS:15622, of

approved brand & manufacturer, in all colours and shade, laid

on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand)

jointing with grey cement slurry @3.3 kg/sqm including grouting 11.41A

the joints with white cement and matching pigments etc. The

tiles must be cut with the zero chipping diamond cutter only .

Laying of tiles will be done with the notch trowel, plier, wedge,

clips of required thickness, leveling system and rubber mallet for

placing the tiles gently and easily.

Double charge vitrified tile polished finish of size 11.41A.1

53 Providing and laying Vitrified tiles in different sizes (thickness to be specified by

manufacturer), with water absorption less than 0.08 % and onforming to I.S. 15622,

of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm

thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement

slurry @ 3.3kg/sqm including grouting the joint with white cement & matching

pigments etc. complete. Size of Tile 600x600 mm 1792.32

54 Providing and laying flamed finish Granite stone flooring in required design and

patterns, in linear as well as curvilinear portions of the building all complete as per

the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick

base of cement mortar 1:4 (1 cement : 4coarse sand) laid and jointed with cement

slurry and pointing with white cement slurry admixed with pigment of matching

shade including rubbing, curing and polishing etc. all complete as specified and as 11.55.1 40.39 SQM 127,847.27

directed by the Engineer-in-Charge :Flamed finish granite stone slab Jet Black,

Cherry Red, Elite

Brown, Cat Eye or equivalent.

55 Providing and laying Polished Granite stone flooring in required design and

patterns, in linear as well as curvilinear portions of the building all complete as per

the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick

base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement

slurry and pointing with white cement slurry admixed with pigment of matching 11.56.1 65.07 SQM 310,855.01

shade including rubbing, curing and polishing etc. all complete as specified and as

directed by the Engineer-in-Charge.

Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent

S.N. DESCRIPTION OF ITEM DSR- AMOUNT DSR AMOUNT

QUANTITY UNIT RATES

2021 ITEM [M.R. ITEM]

56 Providing and laying C.C. pavement of mix M-25 with ready mixed

concrete from batching plant. The ready mixed concrete shall be laid and

finished with screed board vibrator , vacuum dewatering process and

finally finished by floating, brooming with wire brush etc. complete as per

specifications and directions of Engineer-incharge. 16.75 40.17 CUM 406,384.63

(The panel shuttering work shall be paid for separately).

(Note:- Cement content considered in this item is @ 330 kg/cum.

Excess/less cement used as per design mix is payable/ recoverable

separately). 10116.62

57 Providing and fixing false ceiling at all height including providing and

fixing of frame work made of special sections, power pressed from

M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both

side inclusive) as per IS : 277 and consisting of angle cleats of size

25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at

1200 mm centre to centre, one flange fixed to the ceiling with dash

fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange

of cleat fixed to the angle hangers of 25x10x0.50 mm of required

length with nuts & bolts of required size and other end of angle

hanger fixed with intermediate G.I. channels 45x15x0.9 mm running

at the spacing of 1200 mm centre to centre, to which the ceiling

section 0.5 mm thick bottom wedge of 80 mm with tapered flanges

of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre,

shall be fixed in a direction perpendicular to G.I. intermediate channel

with connecting clips made out of 2.64 mm dia x 230 mm long G.I.

wire at every junction, including fixing perimeter channels 0.5 mm

thick 27 mm high having flanges of 20 mm and 30 mm long, the

perimeter of ceiling fixed to wall/partition with the help of rawl plugs

at 450 mm centre, with 25mm long dry wall screws @ 230 mm

interval, including fixing of gypsum board to ceiling section and

perimeter channel with the help of dry wall screws of size 3.5 x 25

mm at 230 mm c/c, including jointing and finishing to a flush finish

of tapered and square edges of the board with recommended jointing

compound , jointing tapes , finishing with jointing compound in 3

layers covering upto 150 mm on both sides of joint and two coats of

primer suitable for board, all as per manufacturer's specification and

also including the cost of making openings for light fittings, grills,

diffusers, cutouts made with frame of perimeter channels suitably

fixed, all complete as per drawings, specification and direction of

the Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum plain board

conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) 1400.55

58 Providing and fixing tiled false ceiling of specified materials of size

595x595 mm in true horizontal level, suspended on inter locking

metal grid of hot dipped galvanized steel sections ( galvanized @

120 grams/ sqm, both side inclusive) consisting of main "T" runner

with suitably spaced joints to get required length and of size 24x38

mm made from 0.30 mm thick (minimum) sheet, spaced at 1200

mm center to center and cross "T" of size 24x25 mm made of 0.30

mm thick (minimum) sheet, 1200 mm long spaced between main

"T" at 600 mm center to center to form a grid of 1200x600 mm and

secondary cross "T" of length 600 mm and size 24x25 mm made of

0.30 mm thick (minimum) sheet to be interlocked at middle of the

1200x600 mm panel to form grids of 600x600 mm and wall angle of

size 24x24x0.3 mm and laying false ceiling tiles of approved texture

in the grid including, required cutting/making, opening for services

like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main

"T" runners to be suspended from ceiling using GI slotted cleats of

size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50

mm long dash fasteners, 4 mm GI adjustable rods with galvanised

butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm

center to center along main T, bottom exposed width of 24 mm of all

T-sections shall be pre-painted with polyester paint, all complete for

all heights as per specifications, drawings and as directed by

Engineer-in-charge.

GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595

mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100

gms/sqm (both sides inclusive) and electro statically polyester powder coated of 12.52.1 65.58 SQM 127,575.40

thickness 60 microns

(minimum), including factory painted after bending. 1945.34

59 12mm cement plaster in single coat on fair side of single or half brick wall for

exterior plastering up to floor two level including internal rounded angles chamfers,

and/or rounded angles not exceeding 80mm in girth and finished even and smooth 13.4.2 1289.660 SQM 463,955.19

no extra for mixing any additive. 1:6 (1 cement: 6 coarse sand)

60 15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1

cement: 6 coarse sand) 414.44

S.N. DESCRIPTION OF ITEM DSR- AMOUNT DSR AMOUNT

QUANTITY UNIT RATES

2021 ITEM [M.R. ITEM]

61 6 mm cement plaster on celling (a) 1:3(1 cement:3 fine sand) 13.16.1 805.820 SQM 309.28 249,224.01

62 Finishing walls with textured exterior paint of required shade: New work (Two or

more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior 13.45.1 1289.660 SQM 386,162.89

primer applied @ 2.20kg/10 sqm 299.43

63 Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50

gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt

resistance exterior paint of required shade (Company Depot Tinted) with silicon

New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including

priming coat of exterior primer applied @ 0.90 litre/10 sqm. 188.77

Applying priming coat: 13.50

64 With ready mixed red oxide zink chromate primer of approved brand and

manufacture on steel galvanised iron/steel works. 67.83

65 Wall painting with acrylic emulsion paint of approved brand and manufacture to give

an even shade :

Two or more coats on new work. 13.60.1 3173.670 SQM 168.47 534,668.18

66 Painting with synthetic enamel paint of approved brand and manufacture to give

Two or more coats on new work. 13.61.1 905.990 SQM 160.65 145,547.29

67 Providing and applying white cement based putty of average thickness 1 mm, of

approved brand and manufacturer, over the plastered wall surface to prepare the 13.80 4463.330 SQM 675,569.63

surface even and smooth complete. 151.36

L ALUMINIUM WORK

68 Providing and fixing aluminium work for doors, windows, ventilators

and partitions with extruded built up standard tubular sections/

appropriate Z sections and other sections of approved make

conforming to IS: 733 and IS: 1285, fixing with dash fasteners of

required dia and size, including necessary filling up the gaps at

junctions, i.e. at top, bottom and sides with required EPDM rubber/

neoprene gasket etc. Aluminium sections shall be smooth, rust free, 21.1

straight, mitred and jointed mechanically wherever required including

cleat angle, Aluminium snap beading for glazing / paneling, C.P.

brass / stainless steel screws, all complete as per architectural

drawings and the directions of Engineer-in-charge. (Glazing, paneling

and dash fasteners to be paid for separately) :

For fixed portion 21.1.1

Anodised aluminium (anodised transparent or dyed to required shade according to

IS: 1868, Minimum anodic coating of grade 21.1.1.1 277.440 KG 147,143.08

For shutters of doors, windows & ventilators including

providing and fixing hinges/ pivots and making provision

for fixing of fittings wherever required including the cost 21.1.2

of EPDM rubber / neoprene gasket required (Fittings

shall be paid for separately)

Anodised aluminium (anodised transparent or dyed to required shade according to

IS: 1868, Minimum anodic coating of grade 21.1.2.1 647.360 KG 420,751.63

69 Providing and fixing glazing in aluminium door, window, ventilator

shutters and partitions etc. with EPDM rubber / neoprene gasket

etc. complete as per the architectural drawings and the directions of 21.3

engineer-in-charge . (Cost of aluminium snap beading shall be paid

in basic item):

With float glass panes of 8 mm thickness (weight not

less than 20 kg/sqm) 1828.56

M Water Proofing

70 Providing and laying in situ seven course water proofing treatment

with APP (Atactic poly-propylene) modified Polymeric memberane

over roof consisting of first coat of bitumen primer @ 0.40 litre per

sqm, 2nd, 4th & 6th courses of bonding material @ 1.20 Kg/sqm,

which shall consist of blown type bitumen of grade 85/25 conforming

to IS : 702, 3rd and 5th layers of roofing membrane APP modified

Polymeric membrane 1.5 mm thick of 2.25 Kg/sqm weight consisting

of five layers prefabricated with centre core as 20 micron HMHDPE

film sandwiched on both sides with polymeric mix and the polymeric

mix is protected on both side with 20 micron HMHDPE film. 7th, the

top most layer shall be finished with brick tiles of class designation

10 grouted with cement mortar 1:3 (1cement : 3 fine sand) mixed

with 2% integral water proofing compound by weight of cement over

a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and

finished neat (item of laying brick tiles shall be paid for separately).

S.N. DESCRIPTION OF ITEM DSR- AMOUNT DSR AMOUNT

QUANTITY UNIT RATES

2021 ITEM [M.R. ITEM]

71 Providing and laying brick tiles over mumty roofs, grouted with cement

mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water

proofing compound by weight of cement, over 12 mm layer of cement

mortar 1:3 (1 cement : 3 fine sand) and finished neat:

With common burnt clay F.P.S. (non modular) brick tiles

of class designation 10

N Roof Sheeting

72 Design, supply, installation and testing High Quality Self supporting Roof

system with Colour coated galvalume Sheet (BMT 1.3MM, APT 1.35MM,

Yield Strength 350 Mpa Coating AZ 150 GSM, Colour 50% off white+ MR 782.17 SQM 3256.80 2,547,358.23

50% blue) With hangers for conduits etc wherever required all work shall

be executed as per technical specification and direction of E/I

O Loft and Wardrobes

All works above plinth level upto floor V level

74 Suspended floors, roofs, landings, balconies and access platform. 5.9.3 8.400 Sqm 936.86 7,869.62

Steel reinforcement for R.C.C. work including straightening, cutting, bending,

placing in position and binding all complete above plinth level. Thermo-

75 Mechanically Treated bars of grade Fe-500 D or more. 5.22.A.6 63.000 Kg 109.57 6,902.79

12mm cement plaster in single coat on fair side of single or half brick wall for

exterior plastering up to floor two level including internal rounded angles chamfers,

and/or rounded angles not exceeding 80mm in girth and finished even and smooth

no extra for mixing any additive. 1:6 (1 cement: 6 coarse sand)

77 6 mm cement plaster on celling (a) 1:3 (1 cement:3 fine sand) 13.16.1 8.400 Sqm 309.27 2,597.88

Wall painting with acrylic emulsion paint of approved brand and manufacture to give

78 an even shade : 13.60

79 Two or more coats on new work. 13.60.1 17.850 Sqm 168.48 3,007.31

Providing and applying white cement based putty of average thickness 1 mm, of

approved brand and manufacturer, over the plastered wall surface to prepare the

80 surface even and smooth complete. 13.80 17.850 Sqm 151.37 2,701.89

Providing wood work in frames of false ceiling, partitions etc. sawn and

81 fixed in position with necessary stainless steel screws etc. 9.3

Kiln seasoned and chemically treated hollock wood 9.3.2 0.183 Cum 78625.27 14,378.99

Providing and fixing cup board shutters 25 mm thick, with Pre-laminated

flat pressed three layer particle board or graded wood particle board IS:

12823 marked, exterior grade (Grade l Type ll), having one side

decorative lamination and other side balancing lamination, including IInd

class teak wood lipping of 25 mm wide x12 mm thick with necessary

screws and bright finished stainless steel piano hinges, complete as per

82 direction of the Engineer-in-Charge 9.129 36.727 Sqm 2423.21 88,997.17

Providing and fixing Pre-laminated medium density fibre board IS:

14587:1998 marked, with one side decorative lamination other side

balancing lamination Grade-I (exterior grade) in shelves with screws and

fittings wherever required, edges to be sealed with PVC edge bending

tape 2.00 mm thick of approved brand (fittings to be paid separately).

Pre-laminated with decorative lamination one side and other side

balancing lamination exterior Grade - I MDF Board 18 mm thick

Providing and fixing magnetic catcher of approved quality in cupboard /

ward robe shutters, including fixing with necessary screws etc. complete.

Double strip (horizontal type) 9.114.2 26.000 Each 41.74 1,085.17

Providing and fixing 18 mm thick gang saw cut, mirror polished,

premoulded and prepolished, machine cut for kitchen platforms, vanity

counters, window sills, facias and similar locations of required size,

approved shade, colour and texture laid over 20 mm thick base cement

mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement,

mixed with matching pigment, epoxy touch ups, including rubbing,

curing, moulding and polishing to edges to give high gloss finish etc.

complete at all levels. 8.2

85 Granite of any colour and shade 8.2.2

Providing & Fixing decorative high pressure laminated sheet of plain /

wood grain in gloss / matt/ suede finish with high density protective

surface layer and reverse side of adhesive bonding quality conforming to

IS : 2046 Type S, including cost of adhesive of approved quality 1 mm

S.N. DESCRIPTION OF ITEM DSR- AMOUNT DSR AMOUNT

QUANTITY UNIT RATES

2021 ITEM [M.R. ITEM]

Providing and fixing wooden moulded beading to door and window

frames with iron screws, plugs and priming coat on unexposed surface

87 etc. complete :

Kiln seasoned and chemically treated hollock wood 50x20mm 9.40.2.2 87.400 RMT 223.72 19,553.07

Providing and fixing special quality chromium plated brass cupboard locks

with six levers of approved quality including necessary screws etc.

Providing and fixing chromium plated brass handles with necessary

89 screws etc. complete: 100mm 9.92.2 26.000 Each 243.46 6,329.89

Badminton court line marking by acrylic paint of approved make and as

per direction of Engineer-Incharge (tentative area of hall 625 Sqm for 2 69,899.00

90 badmintan court) MR 1 Job 69899

SUMMARY SHEET FOR PLUMBING WORKS INTERNAL &

Amount (In Rs.)

S.N Description

I. INTERNAL WORKS

A. SUB HEAD -I : SANITARY FIXTURES & FITTINGS 377,205.60 88,128.00

B. SUB HEAD-II- SOIL , WASTE VENT AND RAIN WATER PIPE 91,221.74 433,548.00

C. SUB HEAD- III - INTERNAL WATER SUPPLY 331,036.30 31,204.00

II. EXTERNAL WORKS

A. SUB HEAD- IV EXTERNAL SEWARAGE LINE 434,528.06 -

B. SUB HEAD-V -EXTERNAL WATER SUPPLY 39,284.35 40,000.00

BOQ FOR PLUMBING WORKS

S.N Description QTY Unit

ITEM CODE DSR 2021 MR DSR 2021 MR AMOUNT

A. SUB HEAD -I : SANITARY FIXTURES & FITTINGS

DSR -17.2.1 Providing and Fixing white viterous china pedestal type water closet (

European type WC Pan ) with seat and lid , 10 litre low level White pvc flushing

cistern , including flush pipe with manually controlled device ( handle lever ) ,

1 Conforming to IS : 7231 with all fittings and fixtures complete including cutting

and making good the walls and floors wherever required . WC Pan with ISI

marked white solid plastic seat and lid .

DSR -17.7 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,

32 mm C.P. brass waste of standard pattern, including painting of fittings and

2 brackets, cutting and making good the walls wherever require :

White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P.

17.7.1 brass pillar tap 9 Each 2780.45 25,024.05

DSR -17.31 Providing and fixing 600x450 mm beveled edge mirror of superior glass ( of

approved quality ) complete with 6 mm thick hard board ground fixed to

wooden cleats with C.P brass screws and washers complete .

Providing and fixing white vitreous china flat back half stall urinal of size

580x380x350 mm with white PVC automatic flushing cistern, with fittings,

standard size C.P. brass flush pipe, spreaders with unions and clamps (all in

C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and

other couplings in C.P. brass, including painting of fittings and cutting and

making good the walls and floors wherever required :

Range of three half stall urinals with 10 litre P.V.C. automatic flushing cistern 1 Each 22667.03 22,667.03

DSR -8.10 Providing and fixing stone slab with table rubbed, edges rounded and polished,

of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a

chase of appropriate width with chase cutter and embedding the stone in the

4 chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse

sand : 4 graded stone aggregate 6 mm nominal size) as per direction of

Engineer-in-charge and finished smooth.

4.1 8.10.2 Granite Stone of approved shade 3 Sqm 4329.99 12,989.97

DSR -18.49 Providing & fixing C.P. brass bib cock of approved quality conforming to IS

17.22A Providing and fixing CP Brass 32mm size bottle trap of approved quality

& make and as per the direction of engineer in charge. 8 Each 1083.16 8,665.28

DSR -18.53 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of

6 approved quality conforming to IS:8931

DSR -18.21 Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts,

7 collar and bush of approved quality and colour.

7.1 18.21.2.1 15 mm nominal bore with 45cm length 30 Each 104.13 3,123.90

DSR -18.53A Providing and fixing CP Brass extension nipple ( size 15mm x 50 mm ) of approved make and quality as per direction of engineer - in - charge .

DSR -17.28 Providing & fixing of Waste pipe for Wash basins & Sinks including pvc waste

9 fittings complete.

BOQ FOR PLUMBING WORKS

S.N Description QTY Unit

ITEM CODE DSR 2021 MR DSR 2021 MR AMOUNT

DSR -18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage

tank, ISI : 12701 marked, with cover and suitable locking arrangement and

10 making necessary holes for inlet, outlet and overflow pipes but without fittings

and the base support for tank.

DSR -18.58 Providing and fixing PTMT grating of approved quality and colour

Providing and fixing 8mm dia C.P./S.S. Jet with flexible tube upto

1meter long with S.S. Triangular plate to european type W.C. Of

approved quality and make as approved by engineer in charge.

NS-3 Providing and fixing vertical or horizontal storage type hot water heater

electrical operated fixed to wall with anchor bolts & nuts, 15mm CP brass

angle stop cock and 15mm CP brass non-return valve complete including

making connections with 15mm dia CP connecting pipes on inlet and outlet,

suitable length of power cable and 15 amps plug .

13.1 a) 15 Litre Capacity 6 Each 12,081.00 72,486.00

17.22B Providing and fixing CP Brass Single lever telephonic wall mixer of

quality & make as approved by Engineer in charge.

(a) 15 mm nominal dia 6 Each 7478.68 44,872.08

17.34 Providing and fixing toilet paper holder :

17.71 Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high 6 Each 178.80 1,072.80

17.73 Providing and fixing PTMT towel rail complete with brackets fixed to wooden

17.73.1 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective 6 Each 701.04 4,206.24

18.22 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet

18.52 Providing and fixing CP brass stop cock (concealed) of standard design and

18.52.1 15mm nominal bore 12 Each 726.89 8,722.68

NS Providing & Fixing of Grab bar size 600X600 mm pipe O.D 32 mm ,

thiickness 2 mm of non slipping grip as per standard specification of use

in disabled toilet complete with brackets suitable for wall installation as

per approved sample complete in all respect. 1 Each 15,642.00 15,642.00

TOTAL OF SUB HEAD - I 377,205.60 88,128.00

B. SUB HEAD-II- SOIL , WASTE VENT AND RAIN WATER PIPE

DSR -12.22 Making khurras 45x45 cm with average minimum thickness of 5 cm cement

concrete 1:2:4 (1 cement:2 coarse sand:4 graded stone aggregate of 20 mm

nominal size) over P.V.C. sheet 1 mx1 mx400 micron, finished 12 mm cement

1 plaster 1:3 (1 cement:3 coarse sand) and a coat of neat cement rounding the

edges and making and finishing the outlet complete

DSR -12.41 Providing and Fixing on wall unplasticised Rigid PVC Rain water pipes

2 conforming to IS : 13592 Type A , including jointing with seal ring conforming

to IS : 5382 , leaving 10 mm gap for thermal expansion

2.1 12.41.2 Single Socketed pipes 110 mm diameter 96 Metre 390.79 37,515.84

DSR -12.44 Providing and Fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams .

DSR -12.37 Providing and Fixing 100 mm diameter and 60 cm long rain water spout in

4 cement mortar 1:4 ( 1 Cement : 4 Fine Sand )

4.1 12.37.1 Stone Ware Spout 2 Each 173.67 347.34

BOQ FOR PLUMBING WORKS

S.N Description QTY Unit

ITEM CODE DSR 2021 MR DSR 2021 MR AMOUNT

DSR -12.42 Providing and Fixing on wall face Rigid Unplasticised UPVC moulded fittings /

accessories for unplasticised Rigid PVC Rain water pipes conforming to IS :

5 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving

10 mm gap for thermal expansion .

12.42.1 Coupler

12.42.2 Single Push Fit Coupler

12.42.3 Single Tee with door

12.42.4 Single Tee without door

12.42.5 Bend 87.5 degree

12.42.6 Shoe ( Plain )

DSR -12.43 Providing and Fixing unplasticised PVC pipe clips of approved design to

unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood

6 plugs , screwed with MS screws of required length , including cutting brick

work with fixing in cement mortar 1:4 ( 1 Cement : 4 Coarse Sand ) and making

good the wall etc . complete

Providing and fixing uPVC 6 Kg/cm2 Soil , Waste & RWP pipes (IS: 13592 Class

B) including all fittings (plain or door) e.g. bends, junction, cowls, offsets,

access pieces, jointing with rubber ring/solvent cement joints including cutting

chase or holes in walls and floors and making good wherever required.

NS-5 Providing & fixing in position upvc P"or S" trap of self cleaning design of

following sizes for the embedded areas Making proper connection with

chemical sealent joint , cutting chase / hole in floors /slabs and bringing the

same in proper condition in cement concrete 1:2:4 mix complete as required.

including cost of cutting and making good the walls and floors where required.

8.1 a) 110 mm inlet and 110 mm outlet 10 Each 734.00 7,340.00

NS-6 Providing & fixing in position upvc floor drain including cost of cutting and

9 making good the walls and floors wherever required.

9.1 a) 110 mm inlet and outlet 18 Each 451.00 8,118.00

NS-7 Providing and fixing uPVC waste pipes for WB , SINK , URINAL , FD (IS: 4985 ) 6

Kg / Sqcm including all fittings (plain or door) e.g. bends, junction, cowls,

10 offsets, access pieces, jointing with rubber ring/solvent cement joints including

cutting chase or holes in walls and floors and making good wherever required.

a) 32 mm OD pipe 12 Metre 282.00 3,384.00

b) 40 mm OD pipe 10 Metre 361.00 3,610.00

NS-13 Providing and fixing Cast bronze chrome plated grating with ring and Stainless

11 steel anti cockroach basket and two SS screw including fixing to the floor with

BOQ FOR PLUMBING WORKS

S.N Description QTY Unit

ITEM CODE DSR 2021 MR DSR 2021 MR AMOUNT

MR Providing and fixing UPVC inlet fitting with maximum 3 inlets 32,40 or 50 mm

size fabricated from 110 mm dia UPVC pipes and fixed to upvc sockets,fixed

to upvc trap with chemical sealent joint and set in cement concrete as per

standard drawing complete. 7 Each 4682 - 32,774.00

NS-8 Providing and fixing upvc cleanout plug( Ceiling or Floor) with suitable insert

13 keys for opening, male threaded joint with upvc socket fixed to uPVC pipe

complete in all respects.

13.1 a) 110 mm diameter Pipe 4 Each 538.00 2,152.00

b) 75 mm dia pipe 6 Each 495.00 2,970.00

TOTAL OF SUB HEAD - II 91,221.74 433,548.00

C. SUB HEAD- III - INTERNAL WATER SUPPLY

DSR -18.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having

thermal stability for hot & cold water supply, including all CPVC plain & brass

threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This

1 includes jointing of pipes & fittings with one step CPVC solvent cement and the

cost of cutting chases and making good the same including testing of joints

complete as per direction of Engineer in Charge.

Concealed work, including cutting chases and making good the walls etc.

1.1 18.8.1 15 mm nominal outer dia Pipes 35 Metre 539.16 18,870.60

1.2 18.8.2 20 mm nominal outer dia Pipes 40 Metre 627.89 25,115.60

1.3 18.8.3 25 mm nominal outer dia Pipes 40 Metre 765.15 30,606.00

1.4 18.8.4 32 mm nominal outer dia Pipes 40 Metre 871.11 34,844.40

DSR -18.7 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having

thermal stability for hot & cold water supply, including all CPVC plain & brass

threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This

includes jointing of pipes & fittings with one step CPVC solvent cement and

testing of joints complete as per direction of Engineer in Charge.

Internal work - Exposed on wall

18.7.3 25mm nominal bore 40 Metre 498.65 19,946.00

18.7.4 32 mm nominal bore 40 Metre 612.25 24,490.00

18.7.5 40mm nominal bore 50 Metre 824.17 41,208.50

18.7.6 50mm nominal bore 120 Metre 1132.96 135,955.20

NS-9 Providing and fixing Thermoflex or Careflex thermal insulation tubing, a

elastomeric flexible material having hermetic blister closed cell structure of

2 expanded synthetic rubber over pipes of following nominal bores and

thickness including all required accessories complete as per specification.

9 mm thick ( Pipes in Chases)

2.1 a) For 15 mm dia Pipe 10 Metre 92.00 920.00

2.2 b) For 20 mm dia Pipe 50 Metre 101.00 5,050.00

c) For 32 mm dia Pipe 20 Metre 120.00 2,400.00

NS-10 Providing and Fixing full way lever operated forged brass ball valve of brass

body with forged brass hard chromeplated steel ball tasted to a pressure not

3 less than 15 kg/sqcm with threaded / flanged joints complete with nuts, bolts,

gaskets, washers etc.

3.1 a) 15 mm dia nominal bore 2 Each 250.00 500.00

3.2 b) 20 mm dia nominal bore 5 Each 340.00 1,700.00

3.3 c) 25 mm dia nominal bore 5 Each 512.00 2,560.00

3.4 d) 32 mm dia nominal bore 4 Each 774.00 3,096.00

3.5 e) 40 mm dia nominal bore 3 Each 1,195.00 3,585.00

BOQ FOR PLUMBING WORKS

S.N Description QTY Unit

ITEM CODE DSR 2021 MR DSR 2021 MR AMOUNT

NS-11 Providing, fixing, testing and commissioning of motorised butterfly valve of

following dia for filling of overhead water tank complete with high and low

level control switches to control tanks. The level controllers shall be installed in

overhead tanks. The level switch will close the valve when water level is high in

4 overhead tank and open the valve when overhead water tank level is low. The

system should be complete in all respects with accessories 220 V AC / 24 V DC,

IP67 electrical water level control unit, copper control wiring in whether proof

4.1 a) 40 mm dia nominal bore 1 Each 11,393.00 11,393.00

TOTAL OF SUB HEAD - III 331,036.30 31,204.00

SUB HEAD- IV EXTERNAL SEWARAGE LINE

2.1 Excavating trenches of required width for pipes, cables, etc including

excavation for sockets, anddressing of sides, ramming of bottoms, depth up to

1.5 m, including getting out the excavated soil, and then returning the soil as

required, in layers not exceeding 20 cm in depth, including consolidating each

deposited layer by ramming, watering, etc. and disposing of surplus excavated

soil as directed,within a lead of 50 m :

2.10.1 All kinds of soil

2.10.1.2 Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia 130 METER 510.08 66310.4

19.4.1.1 Providing and fixing square-mouth S.W. gully trap class SP-1 complete with

C.I. grating brick masonry chamber with water tight C.I. cover with frame of

300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and

frame to be not less than 2.70 kg as per standard design: 100x100 mm size P

type. With common burnt clay F.P.S. (non modular) bricks of class designation

19.7 Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4

coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4

graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix

(1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size),

inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse

sand) finished with floating coat of neat cement and making channels in

cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20

mm nominal size) finished with a floating coat of neat cement complete as per

standard design :

19.7.1 Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light

duty) 455x610 mm internal dimensions,total weight of cover and frame to be

not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :

19.7.1.1 With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

19.28 Constructing brick masonry road gully chamber 45x45x77.5 cm with bricks in

cement mortar 1:4 (1 cement : 4 coarse sand ) with precast R.C.C. vertical

grating complete as per standard design :

19.28.1 with common burnt clay F.P.S.(non module) brick of class designation 7.5

19.1 Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff

mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand)

including testing of joints etc. complete :

19.2 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10

graded stone aggregate 40 mm nominal size) all-round S.W. pipes including

bed concrete as per standard design :

19.16 Providing orange colour safety foot rest of minimum 6 mm thick plastic

encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786,

having minimum cross section as 23 mmx25 mm and over all minimum length

263 mm and width as 165 mm with minimum 112 mm space between

protruded legs having 2 mm tread on top surface by ribbing or chequering

besides necessary and adequate anchoring projections on tail length on 138

mm as per standard drawing and suitable to with stand the bend test and

chemical resistance test as per specifications and having manufacture's

permanent identification mark to be visible even after fixing, including fixing in

manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse

sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

19.21 Making connection of drain or sewer line with existing manhole including

BOQ FOR PLUMBING WORKS

S.N Description QTY Unit

ITEM CODE DSR 2021 MR DSR 2021 MR AMOUNT

19.21.1 For pipes 100 to 250 mm diameter 1 EACH

19.9 Constructing brick masonry circular type manhole 0.91 m internal

dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement

: 4 coarse sand), inside cement plaster 12 mm thick with cement

mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat

of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse

sand : 6 graded stone aggregate 40 mm nominal size), and making

necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse

sand : 4 graded stone aggregate 20 mm nominal size) finished

with a floating coat of neat cement, all complete as per standard

19.9.1 0.91 m deep with SFRC cover and frame (heavy duty, HD-

20 grade designation) 560 mm internal diameter conforming

to I.S. 12592, total weight of cover and frame to be not

less than 182 kg., fixed in cement concrete 1:2:4 (1 cement

: 2 coarse sand : 4 graded stone aggregate 20 mm

nominal size) including centering, shuttering all complete.

(Excavation, foot rests and 12mm thick cement plaster at

the external surface shall be paid for separately) :

19.9.1.1 With common burnt clay F.P.S. (non modular) 1 EACH 14527.34 14527.34

TOTAL OF SUB HEAD - IV 434,528.06 -

SUB HEAD- V EXTERNAL WATER SUPPLY

MR Supplying, installing, testing and commissioning vertical on line multi stage

centrifugal pumping set with mechanical seal, C.I. volute and SS impeller & SS

shaft connected to a TEFC induction motor of suitable HP for 415 volts, 3

phase, 50 cycles A.C. supply with 150 mm dia pressure gauge with

SS/gunmetal isolation cock, vibration eliminating pads, base plate wiring upto

panel and equipment for water level controller to start and stop the pump

automatically at predecided levels of the water in the tank with provision of

protection for dry run etc. complete in all respect (The shop drawing or the

pumps along with its characteristics curves, model and technical data etc. are

to be submitted for approval before purchase of pump).

Domestic water pumps (Treated water transfer pump to terrace tank) (1W+1S)

Capacity 50 lpm

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c

cutting and making good the walls etc.

Internal work - Exposed on wall

18.10.6 50 mm dia nominal bore 25 RMT 1091.65 27291.25

18.12 Providing and fixing G.I. pipes complete with G.I. fittings including

trenching and refilling etc.

18.12.6 External work 15 RMT 799.54 11993.1

TOTAL OF SUB HEAD - IV 39,284.35 40,000.00

COST SUMMARY FOR ELECTRICAL WORK

S.NO. DESCRIPTION DSR-2022 MR

I SUBHEAD - I - CIRCUIT CUM POINT WIRING RS. 1,323,423.68 59,965.14

II SUBHEAD - II - FITTINGS & FIXTURES RS. 5,690.48 581,454.23

III SUBHEAD - III - MAIN BOARDS RS. - 190,800.00

IV SUBHEAD - IV - DISTRIBUTION BOARDS RS. 106,889.37 -

I SUBHEAD - V - EARTHING RS. 79,380.36 16,000.00

II SUBHEAD - VI - SUPPLYING & LAYING OF CABLE RS. 18,394.58 35,231.06

III SUB HEAD -VII :EXTERNAL LIGHT RS. - 70,537.32

ESTIMATE OF ELECTRICAL WORKS

S.No. Code No. Description of items Unit

Qty DSR-2022 MR DSR-2022 MR

SUBHEAD - I - CIRCUIT CUM POINT WIRING

Wiring for light point/ fan point/ exhaust fan point/ call bell point with

1.5 sq.mm FRLS PVC insulated copper conductor single core cable in

surface / recessed medium class PVC conduit, with modular switch,

modular plate, suitable GI box and earthing the point with 1.5 sq.mm

FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for group controlled (looped) light point/fan point/exhaust fan

point/ call bell point ( without Independent switch etc.) with 1.5 sq. mm

FRLS PVC insulated copper conductor single core cable in surface/

recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS

PVC insulated copper conductor single core cable etc as required.

(Switch Control Secondary Points)

Wiring for light point/ fan point/ exhaust fan point/ call bell point with

1.5 sq.mm FRLS PVC insulated copper conductor single core cable in

surface / recessed steel conduit, with modular switch, modular plate,

suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable etc. as required. (Switch

Control Primary Points)

Wiring for group controlled (looped) light point/fan point/exhaust fan

point/ call bell point (without Independent switch etc.) with 1.5 sq. mm

FRLS PVC insulated copper conductor single core cable in surface/

recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS

PVC insulated copper conductor single core cable etc as required.

(Switch Control Secondary Points)

MCB CONTROL LIGHT POINTS

Wiring for light point/ fan point/ exhaust fan point/ call bell point with

2.5 sq.mm FRLS PVC insulated copper conductor single core cable in

surface / recessed steel conduit, with modular switch, modular plate,

suitable GI box and earthing the point with 2.5 sq.mm FRLS PVC

insulated copper conductor single core cable etc. as required. (Switch

Control Primary Points)

5.1 NSI-1.1 Primary point controlled by one MCB. Point 12 1,535.50 18,426.00

Same as item above but Secondary point. i.e. Points to be looped with

5.2 NSI-1.2 Point

Primary point with 2.5 sqmm wire and Point wiring 12 1,365.90 16,390.80

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated

copper conductor single core cable in surface/ recessed steel conduit

6 DSR 1.5 Metre

alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single

core cable for loop earthing as required. 350 529.20 185,220.00

Wiring for circuit/ submain wiring alongwith earth wire with the

7 DSR 1.7 following sizes of FRLS PVC insulated copper conductor, single core

cable in surface/ recessed steel conduit as required.

7.1 DSR 1.7.1 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire Metre 50 399.66 19,983.00

7.2 DSR 1.7.2 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire Metre 955 450.99 430,695.45

7.3 DSR 1.7.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre 100 719.87 71,987.00

7.4 DSR 1.7.5 2 x 10 sq. mm + 1 x 6 sq.mm earth wire Metre 150 867.74 130,161.00

7.5 DSR 1.7.10 4 X 10 sq. mm + 2 X 6 sq. mm earth wire Metre 100 1425.05 142,505.00

7.6 DSR 1.7.11 4 X 16 sq. mm + 2 X 6 sq. mm earth wire Metre 60 2010.48 120,628.80

Supplying and fixing suitable size GI box with modular plate and

cover in front on surface or in recess, including providing and

8 DSR 1.31 Each

fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular

switch, connections etc. as required. 16 582.98 9,327.68

S.No. Code No. Description of items Unit

Qty DSR-2022 MR DSR-2022 MR

Supply and Wiring for 250 volts single phase and neutral 2 Nos 6 amps

socket outlate with control by 1 No switched with 2.5 sq.mm PVC

insulated copper conductor 1100 volts grade stranded flexible FRLS

wires in concealed or surface mounted 25 mm dia 2mm thick PVC

conduit including providing and fixing of 6 amps 3 pin switch socket

9 NSI-2 outlet of aprpoved make and design in 2 mm thick GI box with grid Each

plate and earthing of third pin of the socket with 2.5 Sq. mm PVC

insulated copper conductor stranded flexible FRLS wire.(maximum

four no. of switches socket shall be connected on one circuit)

Supplying and fixing suitable size GI box with modular plate and

cover in front on surface or in recess, including providing and

10 DSR 1.32 Each

fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A

modular switch, connections etc. as required. 15 716.19 10,742.85

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/

11 DSR-1.33 Each

wooden block including connections etc. as required. 2 106.33 212.66

Supplying & fixing suitable size GI box wih modular plate and cover in

front on surface or in recess i/c providing and fixing 25 amp modular

12 DSR-1.57 socket outlet and 25 Amps modular SP MCB, “C” curve including Each

connection, painting etc. as required. (AC's & Gysers)

Supplying and fixing following modular switch/ socket on the

13 DSR 1.24 existing modular plate & switch box including connections but

excluding modular plate etc. as required.

13.1 DSR 1.24.6 Telephone socket outlet Nos 4 180.88 723.52

Supplying and fixing following size/ modules, GI box alongwith

14 DSR 1.27 modular base & cover plate for modular switches in recess etc.

Supplying and fixing following size/ modules, GI box alongwith

15 DSR 1.24 modular base & cover plate for modular switches in recess etc.

15.1 DSR 1.24.4 3 pin , 5/6 amps socket outlet Each 2 149.11 298.22

Supplying and fixing following size/ modules, GI box alongwith

16 DSR 1.27 modular base & cover plate for modular switches in recess etc.

Supplying and fixing of following sizes of medium class PVC

conduit along with accessories in surface/recess including

cutting the wall and making good the same in case of recessed

conduit as required.

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated

18.1 1.18 annealed copper conductor, unarmored telephone cable in the existing

surface/ recessed steel/ PVC conduit as required.

TOTAL CARRIED TO SUMMARY FOR SUBHEAD - I 1,323,423.68 59,965.14

SUBHEAD - II - FITTINGS & FIXTURES

Supply, Installation, Testing and Commissioning of 9 W Bulk head Light.

2 NSI-2 Supply, Installation, Testing and Commissioning of 5W Mirror Light. Each 2 1,077.79 2,155.58

Supply, Installation, Testing and Commissioning of 18W

Recessed/Surface Mounted LED circular Downlighter. 86 1,975.94 169,930.84

Supply, Installation, Testing and Commissioning of 20W Wall/Surface

S.No. Code No. Description of items Unit

Qty DSR-2022 MR DSR-2022 MR

Supply, Installation, Testing and Commissioning of 65W Surface

mounted LED Bay light. 10 6,107.46 61,074.60

Supply, Installation, Testing and Commissioning of 12W Recessed

mounted LED circular Downlighter (Cat no-Bajaj Lighting BGSLO SLEEK

SURFACE 12W WH RD or equivalent as specified in the approved list of

Supply, Installation, Testing and Commissioning of 150W highway with

150LPW Ceiling mounted LED Light Fixtures 5 7,469.82 37,349.10

Supply, Installation, Testing and Commissioning of 250W Highway with

8 NSI-8 130LPW ceiling mounted LED Light Fixtures Each 15

Supply, Installation, Testing and Commissioning of 1200 mm sweep,

BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC)

Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2

nos. canopies, shackle kit, safety rope, copper winding, Power Factor

not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery

9 DSR 19.1 minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD Each

less than 10%, remote or electronic regulator unit for speed control and

all remaining accessories including safety pin, nut bolts, washers,

temperature rise=75 degree C (max.), insulation resistance more than 2

mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing

etc. complete as required.

Supplying and fixing two module stepped type electronic fan

10 DSR 1.25 regulator on the existing modular plate switch box including Each

connections but excluding modular plate etc. as required. 8 450.99 3,607.92

Installation, testing and commissioning of ceiling fan, including

wiring the down rods of standard length (upto 30 cm) with 1.5

11 DSR 1.44 Each

sq. mm FRLS PVC insulated, copper conductor, single core cable

etc. as required. 8 260.32 2,082.56

12 NSI-9 Supply of 300 mm dia Domestic Exhaust Fan Each 4 2,155.58 8,622.32

13 NSI-10 Supply of heavy duty 450mm Wall Fan each 3 6,848.44 20,545.32

TOTAL CARRIED TO SUMMARY FOR SUBHEAD - II 5,690.48 581,454.23

SUBHEAD - III - MAIN BOARDS

Supplying, installing, testing & commissioning of following type

compartmentalised wall mounted / floor mounted cubicle board made

from 2mm thick CRCA sheet dust & vermin proof duly phosphatized &

1 powder coated inclusive of suitable size 4 strip Al. Busbar complete with

interconnection providing Lugs, inter-earthing, painting etc. i/c

providing & fixing below noted accessories:

Receiving,unloading,storing, handling, installation, testing and

commissioning of following MV Switchboards complete as required and

as per site condition and dimension of all panels shall be carried out as

per the attachad sld

1 NSI-1 MAIN LT PANEL ( FOR BUILDING ) Set 1 150,800.00 150,800.00

2 NSI-2 FIRE FIGHTING PANEL Set 1 40,000.00 40,000.00

TOTAL CARRIED TO SUMMARY FOR SUBHEAD - III - 190,800.00

SUBHEAD - IV - DISTRIBUTION BOARDS

Supplying and fixing following way, single pole and neutral,

sheet steel, MCB distribution board, 240 V, on surface/ recess,

1 DSR 2.3 complete with tinned copper bus bar, neutral bus bar, earth

bar, din bar, interconnections, powder painted including

earthing etc. as required. (But without MCB/RCCB/Isolator)

1.2 DSR 2.3.2 8 way, Double door Each 1 3144.66 3,144.66

1.3 DSR 2.3.3 12 way, Double door Each 2 2829.34 5,658.68

S.No. Code No. Description of items Unit

Qty DSR-2022 MR DSR-2022 MR

Supplying and fixing following way, three pole and neutral, sheet steel,

MCB distribution board, 415 volts, on surface/ recess complete with

tinned copper busbar, neutral busbar, earth bar, din bar, detachable

gland plate, interconnections, phosphatized and powder painted

including earthing etc. as required. (But without MCB/ RCCB/ Isolator)

Supplying and fixing of following ways surface/ recess mounting,

vertical type, 415 V, TPN MCB distribution board of sheet steel, dust

protected, duly powder painted, inclusive of 200 A tinned copper bus

3 DSR 2.5 bar, common neutral link, earth bar, din bar for mounting MCBs (but

without MCBs and incomer) as required . (Note :Vertical type MCB

TPDB is normally used where 3 phase outlets are required.)

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve,

miniature circuit breaker suitable for inductive load of following poles in

the existing MCB DB complete with connections, testing and

commissioning etc. as required.

Supplying and fixing following rating, double pole, 240 V, isolator in the

5 DSR 2.12 existing MCB DB complete with connections, testing and commissioning

etc. as required.

Supplying and fixing following rating, four pole, 415 V, isolator in the

6 DSR 2.13 existing MCB DB complete with connections, testing and commissioning

etc. as required.

Supplying and fixing following rating, double pole, (single phase and

neutral), 240 V, residual current circuit breaker (RCCB), having a

sensitivity current 30 mA in the existing MCB DB complete with

connections, testing and commissioning etc. asrequired.

S.No. Code No. Description of items Unit

Qty DSR-2022 MR DSR-2022 MR

Supplying and fixing DP sheet steel enclosure on surface/ recess

8 DSR-2.16 along with 25/32 A 240 V "C" curve DP MCB complete with Each

connections, testing and commissioning etc. as required. 3 1428.73 4,286.19

Supplying and fixing single pole blanking plate in the existing

9 DSR 2.11 Each

MCB DB complete etc. as required. 5 15.89 79.45

TOTAL CARRIED TO SUMMARY FOR SUBHEAD - IV 106,889.37 -

SUBHEAD - V - EARTHING

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including

accessories, and providing masonary enclosure with cover plate having

1 DSR 5.4 Sets

locking arrangement and watering watering pipe 2.7 metre long etc.

with charcoal/ coke and salt as required. 1 9132.09 9,132.09

Earthing with Cu. earth Plate 600mm x 600mm x 3mm thick including

accesssories, and providing masonary enclosure with cover plate (CI

2 DSR 5.6 heavy duty) having locking arrangement and watering pipe pipe of 2.7 Sets

mtr long etc. with charcoal or coke and salt) as required.

Supplying and laying 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe

3 DSR 5.11 from earth electrode, including connection with G.I. nut, bolt, spring, Mtr

washer excavation and refilling etc. as required. 20 862.86 17,257.20

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess

4 DSR-5.14 for connections etc. as required. 2 nos used for 50 x 5 for the Neutral Mtr

earthing of euipments ) 20 1420.17 28,403.40

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for

5 DSR 5.15 Mtr

connections etc. as required. 20 298.21 5,964.20

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop

6 DSR 5.16 Mtr

earthing etc. as required. 20 85.55 1,711.00

S.No. Code No. Description of items Unit

Qty DSR-2022 MR DSR-2022 MR

Supplying, fixing, testing and commissioning of following bare Copper/

7 NSI-1 GI flat including all necessary fixing accessories and effecting

Supply and laying medium class GI pipe under road/paved areas/wall

8 NSI-2 crossing etc. including earth excavations refilling, ramming and making

good as approved.

8.1 NSI-2.1 150 mm dia GI pipe Class B Metre 10 1,600.00 16,000.00

TOTAL CARRIED TO SUMMARY FOR SUBHEAD - V 79,380.36 16,000.00

SUBHEAD - VI - SUPPLYING & LAYING OF CABLE

Laying of one number PVC insulated and PVC sheathed / XLPE power

cable of 1.1 KV grade of following size direct in ground including

1 DSR 7.1 excavation, sand cushioning, protective covering and refilling the trench

Laying of one number additional PVC insulated and PVC sheathed /

XLPE power cable of 1.1 KV grade of following size direct in ground in

2 DSR 7.2 the same trench in one tier horizontal formation including excavation,

sand cushioning, protective covering and refilling the trench etc. as

Supply of following sizes of XLPE insulated Aluminum conductor strip/

3 NSI wire Armoured, overall PVC sheathed 1.1 KV grade cables conforming

to relevant IS-7098 Code and technical specifications.

Supplying and making end termination with brass compression gland

and aluminium lugs for following size of PVC insulated and PVC

sheathed / XLPE aluminium conductor cable of 1.1 KV grade

TOTAL CARRIED TO SUMMARY FOR SUBHEAD - VI 18,394.58 35,231.06

S.No. Code No. Description of items Unit

Qty DSR-2022 MR DSR-2022 MR

SUB HEAD -VII :EXTERNAL LIGHT

Supplying, installation, testing and commissioning of 65W LED Street

Light IP66 LED with High performance having system lumen output of

minimum 9900 lumens, contemporary designed housing made of die-

1 NSI-1 cast aluminium, with street optic LENS for uniform light distribution. PF Nos

better than 0.9, CRI better than 70 complete with all accessories. Wipro

Cat No.: LR 02-102-XXX-57-G2 Street light

SITC of 6m ht. GI pole alongwith control box,6A MCB etc. as required

TOTAL CARRIED TO SUMMARY FOR SUBHEAD -VII - 70,537.32

SUMMARY SHEET FOR FIRE FIGHTING WORKS

SUB HEAD DESCRIPTION AMOUNT DSR AMOUNT NSI

A SUB HEAD - A : PUMPS & EQUIPMENTS 169,084.39 -

B SUB HEAD - B : PIPING HYDRANT & ACCESSORIES SYSTEM 595,852.32 272,329.00

BOQ FOR FIRE FIGHTING WORKS

Item Code No. DSR

S.No Description of items MP HALL QTY UNIT

2022 E &M WORKS

DSR MR DSR MR

A. SUB HEAD - A : PUMPS & EQUIPMENTS

1 18.4 Supplying , Installation , Testing and Commissioning of Electric Driven Terrace

Pump Suitable for Automatic operation and Consisting of Following Complete in all

Respect as Required ( Terrace Fire Pump )

1.1 a) Horizontal Type Multistage , Centrifugal Pump of Cast Iron Body and Bronze

Impeller with Stainless Steel Shaft Mechanical Seal Conforming to IS : 1520

1.2 b) Suitable HP Squirrel cage Induction motor , TEFC , synchronous speed 1500 RPM ,

Suitable for operation on 415 Volts 3 Phase 50 Hz AC Supply with IP 68 protection

for enclosure Horizontal Foot Mounted type with class F insulation Conforming to

IS : 325 with Energy Efficiency class IE-3

1.3 c) MS Fabricated Common Base Plate Coupling , Coupling Guard Foundation bolts etc

1.4 d) Suitable Cement Concrete Foundation duly Plastered with anti vibration Pads

The Head of the Pump is Selected in a manner so as to give a minimum 3.5

kg/sqcm pressure at the highest / farthest point

2 18.20 Supplying and Fixing Air Vessel made of 450 mm dia 8 mm thick ms sheet 2000 mm

in height with air release valve on top and flanged connection to riser drain

arrangement with 25 mm dia gunmetal wheel valve with required accessories

pressure gauge and painting with synthetic enamel paint of approved shade as

TOTAL CARRIED TO SUMMARY SHEET FOR SUB HEAD A 169,084.39 -

B. PIPING, HYDRANT , AND ACCESSORIES SYSTEM

1 18.7 Providing Laying Testing and Commissioning of C class Heavy duty MS Pipe

Conforming to IS : 1239 / 3589 including Fittings like elbows , tees , flanges , tapers

, nuts , bolts , gaskets etc in ground including welding excavation and Providing

cement concrete blocks as supports anticorrosive treatment with coaltar / asphalts

tape as per IS :10221 refilling the trench etc of following sizes complete as required

2 18.11 Supplying Fixing Testing and Commissioning of butterfly valve of PN 1.6 Rating with

Bronze Gunmetal Sheet duly ISI marked complete with nuts , bolts , washers ,

gaskets conforming to IS : 13095 of following sizes as required .

3 18.14 Providing Installation Testing and Commissioning of Non Return Valve of following

sizes conforming to IS : 5312 complete with rubber gasket , GI Bolts , Nuts ,

washers etc as required .

4 18.15 Providing Installation Testing and Commissioning of Stainless Steel Y Strainer

fabricated out of 1.6 mm thick stainless steel , Grade 304 , Sheet with 3 mm dia

holes with stainless steel flange .

5 18.9 Supplying and Fixing Single Headed Internal Hydrant Valve with instantaneous

gunmetal material coupling of 63 mm dia with cast iron wheel ISI marked

conforming to IS : 5290 ( Type A ) with blank Gunmetal material cap and chain as

BOQ FOR FIRE FIGHTING WORKS

Item Code No. DSR

S.No Description of items MP HALL QTY UNIT

2022 E &M WORKS

DSR MR DSR MR

5.1 18.9.1 Single Headed Gunmetal Material 3 Set 9344.76 28,034.28

6 18.13 Supplying and Fixing orifice plate made out of 6 mm thick stainless steel ( Grade

304 ) with orifice of required size to be fitted between flange and landing valve of

external and internal hydrants to reduce pressure at the outlet to the level of 3.5

kg / sqcm complete as required . 4 Each 1614.50 6,458.00

7 18.16 Supplying and Fixing 63 mm dia 15 m Long RRL Hose pipe with 63 mm dia male and

female coupling duly bound with GI wire , rivet etc . Conforming to IS : 636 ( Type A

) as Required .

7.1 18.16.1 Gunmetal Material 3 Set 6357.76 19,073.28

8 18.17 Supplying and Fixing First aid hose reel with MS Construction Spray painted in Post

office red conforming to IS : 884 complete with the following as required

20 mm nominal internal dia water hose thermoplastic ( Textile Reinforced ) Type -

2 as per IS : 12585

20 mm nominal internal dia gunmetal globe valve and nozzle

Drum and Brackets for fixing the equipments on wall

Connections from Riser with 25 mm dia stop gunmetal valve and MS Pipe and

9 18.18 Supplying and Fixing 63 mm dia Gunmetal Short Branch Pipe with 20 mm nominal

internal diameter size nozzle conforming to IS : 903 suitable for instantaneous

connection to interconnect hose pipe coupling as required .

9.1 18.18.1 Gunmetal Material 6 Set 2952.77 17,716.62

10 18.22 Providing and Fixing of Pressure Switch in MS Pipe Line including connection etc as

required 1 Each 1889.49 1,889.49

11 NS-1 Providing and fixing of Fire Hose Cabinet size not less than 2.1 x 1.2 x 0.90 mtr

made out of M.S. sheet not less than 1.5 mm thick having central opening and 4

mm thick glazed glass doors (Two nos.) suitably marked on the outside 'with the

letters "FIRE HOSE" including necessary locking arrangement and painting in PO

red colour suitable to accommodate, internal hydrant valve, 2 nos 15 mtr long

Hose pipe, branch pipe, nozzle and fire man's axe. It shall be fixed inside the FHC

Cabinet Complete as required .

12 NS-2 Providing and fixing weather proof Fire Hose Cabinet of size not less than 0.75 x

0.6 x 0.25 mtr made out of M.S. sheet not less than 1.5 mm thick having central

opening and 4 mm thick glazed glass doors (Two nos.) suitably marked on the

outside 'with the letters "FIRE HOSE" including necessary locking arrangement and

painting in PO red colour suitable to accommodate, external yard hydrant valve,

2 nos 15 mtr long Hose pipe, branch pipe, nozzle and fire man's axe. It shall be

mounted on boundary wall complete as required.

13 NS-3 Providing & fixing Controlled Percolating (CP) Hose ISI marked (IS:8423) 63 mm dia

x 15 m long complete with instantaneous type Stainless steel 63 mm dia ISI

marked Male & Female couplings (IS:903) bound and riveted to hose pipe with

copper rivets and 1.5 mm copper wire.brusting pressure not less than 22

Kg/Sqcm. ( Two nos. for each hydrant-valve) 6 Each 5081.00 30,486.00

14 NS-4 Providing and fixing standard firemans axe with heavy rubber handle. 3 Each 1467.00 4,401.00

15 NS-5 Providing and fixing dial type pressure gauge with isolation cock and copper pipe

on main header Dial diameter 100 mm celebration 0-16 / sq. cm.

16 NS-6 Providing and fixing Fire Extinguishers (CO2 type powder ) 4 Kg Capacity complete

with all accessories as per manufacturers specifications. 1 Each 5647.00 5,647.00

17 NS-7 Providing and fixing Fire Extinguishers (A, B, C type powder ) 5 Kg Capacity

complete with all accessories as per manufacturers specifications. 14 Each 4518.00 63,252.00

BOQ FOR FIRE FIGHTING WORKS

Item Code No. DSR

S.No Description of items MP HALL QTY UNIT

2022 E &M WORKS

DSR MR DSR MR

TOTAL CARRIED TO SUMMARY SHEET FOR SUB HEAD B 595,852.32 272,329.00

COST SUMMARY FOR CONVENTIONAL FIRE ALARM SYSTEM

S.NO. DESCRIPTION DSR-2022 MR

I SUBHEAD - I - FIRE ALARM CONVENTIONAL SYSTEM RS. 69,354.11 87,288.00

Detailed Estimate for LV Works

S.No. Code No. Description of items Unit Total Qty.

DSR-2022 NSI DSR-2022 NSI

DSR 2022 SUBHEAD - I - FIRE ALARM CONVENTIONAL SYSTEM

Supplying, installation, testing & commissioning sector panel suitable for

following zones, complete with visual indications for short circuit fault, open

1 DSR 17.1.9 circuit fault, fire condition and all other standard facilities as per IS:2189 with

mimic diagram for all area/zone covered, complete with all connections,

interconnections as required

Supplying, installation, testing & commissioning of conventional beam detector

with short circuit isolator (inbuilt or seperate) complete with emitter and

receiver including connections with remote test features etc complete as

3 DSR 17.1.2 Supplying, installation, testing & commissioning of smoke detector with builtin Nos. 10 13,945

LED and mounting base complete with all connections etc. as required 1394.50

Supplying, installation, testing & commissioning of manual call boxes of MS

4 DSR 17.1.3 construction in surface/recess with stainless steel chain & hammer assembly Nos. 4 2,259

complete with glass and push button etc. as required. 564.65

Supplying, installation, testing & commissioning fire alarm sounder with facility

to make announcement, mounted in M.S. box (16 SWG) with hinged cover plate

& suitable for operation with amplifier i/c line matching transformer etc.

complete as required. 666.08

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V

rated with annealed copper conductor having XLPE insulation, steel wire

armouring & FRLS outer sheath complete as required.

Supplying and fixing of following sizes of steel conduit along with

accessories in surface/recess including painting in case of surface

conduit, or cutting the wall and making good the same in case of

recessed conduit as required.

ABSTRACT OF COST FOR PROPOSED PQC ROAD

Sl. DSR- Description Qty Unit Rate Amount On Amount On

No. 2021 (In Rs.) DSR-2021 Non- DSR

1 DSR- COST OF ROAD

TOTAL COST 483,390.25 -

ANALYSIS OF RATE FOR PQC ROAD FOR 3.5 MTR WIDE & 10.0 MTR LONG ROAD

Sl. DESCRIPTION OF ITEM UNIT QTY RATE AMOUNT

1 Preparation and consolidation of sub grade with

power road roller of 8 to 12 tonne capacity after

excavating earth to an average of 22.5 cm depth,

16.1 dressing to camber and consolidating with road Sqm 55.000 12,133.00

roller including making good the undulations etc.

and re-rolling the sub grade and disposal of surplus

earthwith lead upto 50 metres. 220.60

Construction of granular sub-base by providing

close graded Material conforming to specifications,

mixing in a mechanical mix plant at OMC, carriage

of mixed material by tippers to work site, for all

leads & lifts, spreading in uniform layers of specified

thickness with motor grader on prepared surface

and compacting with vibratory power roller to

achieve the desired density, complete as per

specifications and directions of Engineer-in-Charge.

3 With material conforming to Grade-I (size range 75

mm to 0.075 mm) having CBR Value-30 1985.43

Construction of dry lean cement concrete sub base

over a prepared sub-grade with coarse and fine

aggregate conforming to IS:383, the size of coarse

aggregate not exceeding 25 mm, aggregate cement

ratio not to exceed 15:1, aggregate gradation after

blending to be as per specifications, cement content

16.8 not to be less than 150 Kg/cum, optimum moisture cum 3.500 17,668.91

content to be determined during trial length

construction, concrete strength not to be less than

10 Mpa at 7 days, mixed in a batching plant,

transported to site, for all leads & lifts, laid with a

mechanical paver, compacting with 8-10 tonne

vibratory roller, finishing and curing etc. complete

as per direc on of Engineer in- charge. 5048.26

Sl. DESCRIPTION OF ITEM UNIT QTY RATE AMOUNT

5 Providing and laying C.C. pavement of mix M-25

with ready mixed concrete from batching plant. The

ready mixed concrete shall be laid and finished with

screed board vibrator , vacuum dewatering process

and finally finished by floating, brooming with wire

brush etc. complete as per specifications and

16.75 directions of Engineer-incharge. cum 4.375 44,260.21

(The panel shuttering work shall be paid for

(Note:- Cement content considered in this item is @

Excess/less cement used as per design mix is

payable/ recoverable separately). 10116.62

6 Providing and filling in position rubberized bitumen Per cm

hot sealing compound for sealing of expansion width

joints in roads / pavements all complete as per per

16.46.1 direction of the Engineer-in-Charge. cm 131.250 1,203.56

Using grade 'A' sealing compound conforming depth

to IS: 1834 per m

7 Providing and laying at or near ground level factory

made kerb stone of M-25 grade cement concrete in

position to the required line, level and curvature,

jointed with cement mortar 1:3 (1 cement: 3 coarse

sand), including making joints with or without

grooves (thickness of joints except at sharp curve

shall not to more than 5mm), including making

drainage opening wherever required complete etc.

as per direction of Engineer-in-charge (length of

finished kerb edging shall be measured for

payment). (Precast C.C. kerb stone shall be

by Engineer-in-charge).

8 Excavating, supplying and filling of local earth

(including royalty) by mechanical transport upto a

2.25a lead of 5km also including ramming and watering of cum 8.500 3,829.68

the earth in layers not exceeding 20 cm in trenches,

plinth, sides of foundation etc. complete. 450.55

Painting with synthetic enamel paint of approved

brand and manufacture of required colour to give an

9 Two or more coats on new work over an under coat

of suitable shade with ordinary paint of approved 2,106.45

13.62.1 brand and manufacture sQM 9.000 234.05

Total Cost for 35 Sqm(DSR Items) 96,677.91

Cost For Per Sqm Area ( DSR Items ) 2,762.23

ABSTRACT OF COST FOR PATHWAY

Sl. DSR- Description Qty Unit Rate Amount

1 Analysis CONSTRUCTION OF PATHWAY 100.00 Sqm 2620.06 262,006.00

FOOTPATH 2.00 MT. WIDE

DETAILS OF MEASUREMENT & ANALYSIS OF RATE

Sl. DESCRIPTION OF ITEM DSR- QTY UNIT RATE AMOUNT

No. 2021 (In Rs.) On DSR

1. Earth work in excavation by mechanical

means (Hydraulic excavator) / manual means

over areas (exceeding 30cm in depth. 1.5 m

in width as well as 10 sqm on plan) including

disposal of excavated earth, lead upto 50m

and lift upto 1.5m, disposed earth to be

levelled and neatly dressed. 2.6

all kinds of soil 2.6.1 1.89 Cum 251.09 474.56

2 Providing and laying in position cement

concrete of specified grade excluding the cost

of centering and shuttering. All work upto

plinth level. -

1:5:10 (1 cement : 5 course bound: 10 graded

stone aggregate 40mm nominal size)

3 Providing and laying 60mm thick faciory made

cement concrete interlocking paver block of M

-30 grade made by block making machine

with strong vibratory compaction, of approved

s;ze, design & shape, laid in required colour

and pattern over and including 50mm thick

compacted bed of coarse sand, filling the

joints with line sand etc. all complete as per

the direction of Engineer-in-charge.

4 Providing and laying at or near ground level

factory made kerb stone of M-25 grade

cement concrete in position to the required

line, level and curvature, jointed with cement

mortar 1:3 (1 cement: 3 coarse sand),

ncluding making joints with or without grooves

(thickness of joints except at sharp curve

shall not to more than 5mm), including

making drainage opening wherever required

complete etc. as per direction of Engineer-in-

charge (length of finished kerb edging shall

be measured for payment). (Precast C.C.

kerb stone shall be approved by Engineer-in-

5 Painting with synthetic enamel paint of

approved brand and manufacture of required

colour to give an even shade : -

Two or more coats on new work over an

under coat of suitable shade with ordinary

paint of approved brand and manufacture 13.62.1 3.00 Sqm 233.93 701.79

Sl. DESCRIPTION OF ITEM DSR- QTY UNIT RATE AMOUNT

No. 2021 (In Rs.) On DSR

6 Excavating, supplying and filling of local earth

(including royalty) by mechanical transport

upto a lead of 5km also including ramming

and watering of the earth in layers not

exceeding 20 cm in trenches, plinth,

sides of foundation etc. complete. 2.25a -

7 Filling available excavated earth (excluding

rock) in trenches, plinth, sides of oundations

etc. in layers not exceeding 20cm in depth,

consolidating each deposited layer by

ramming and watering, lead up to 50 m and

deduct PCC -0.45 -

8 Centering and shuttering including strutting,

propping etc. and removal of form for all

a Foundations, footings, bases of columns, etc.

for mass concrete. 5.9.1 1.50 -

COST OF 20.00 Sqm. Footpath = 52,401.13

Cost of 1.00 Sqm. Footpath = 2,620.06

ABSTRACT OF COST FOR SURFACE DRAIN

Sl. DSR- Description Qty Unit Rate Amount

1 Analysis CONSTRUCTION OF APRON DRAIN

ANALYSIS OF RATE FOR SURFACE DRAIN (250X150 MM)

Sl. DESCRIPITION OF ITEM DSR- QTY. UNIT RATE AMOUNT

Take 1.00 Mtr Length

1 Earth work in excavation by mechanical means

(Hydraulic excavator)/manual means over areas

(exceeding 30 cm in depth, 1.5 m in width as

well as 10 sqm on plan) including getting out

and disposal of excavated earth lead upto 50 m

and lift upto 1.5 m, as directed by Engineer-in-

all kinds of soil 2.6.1 0.43 cum

2 Filling available excavated earth (excluding rock)

in trenches, plinth, sides of foundations etc. in

layers not exceeding 20cm in depth:

consolidating each deposited layer by ramming

and watering, lead up to 50 m and lift up to 1.5

3 Providing and laying in position cement concrete

of specified grade excluding the cost of

centering and shttering - All work up to plinth

1:5:10 (1 cement : 5 coarse sand (zone-III): 10

graded stone aggregate 40 mm nominal size).

4 1:2:4 (1 Cement : 2 coarse sand (zone-III)

derived from natural sources : 4 graded stone

aggregate 40 mm nominal size derived from

natural sources) 4.1.4 0.01 cum

5 Centering and shuttering including strutting,

propping etc. and removal of form for all heights

Foundations, footings, bases of columns, etc. for

mass concrete 5.9.1 0.20 Sqm 376.36 75.27

6 Brick work with F.P.S. bricks of class

designation 75 in foundation and plinth in :

Cement mortar 1:6 (1 cement : 6 coarse sand) 6.1.2

7 12 mm cement plaster finished with a floating

coat of neat cement of mix : 13.7 0.30 Sqm

1:4 (1 cement: 4 fine sand) 13.7.2 0.46 "

Description of Item Qty. Unit Rate Amount

Supply, Installation, Testing & Commissioning of Speaker with below

Specifications:-

Transducer Size : 15" LF Driver + 1 x 1" Horn-loaded Compression Driver

Power Handling : 300 Watts Continuous, 1200W Peak

Dispersion : 90 x 40

Sensitivity : 101 dB

Max SPL : 124dB continuous, 130 dB peak

Approved Makes: OHM, British Acoustics, JBL, Bose, Honeywell

Supply, Installation, Testing & Commissioning of Subwoofer with below

Specifications:-

Transducer Size : 18" Low Frequency Driver

Power Handling : 600 Watts Continuous, 2400W Peak

Dispersion : Omni-directional,

Sensitivity : 101 dB

Max SPL : 129dB continuous, 135 dB peak"

Approved Makes:OHM /British Acoustics/ Bose/ British Acoustics

Supply, Installation, Testing & Commissioning of Class-D Power Amplifier with

below Specifications:-

Number of Channels : 2

Power at 4 Ohms per channel : 1000W

Power at 8 Ohms per channel : 500W

Class-D with LCD Display for critical factors, dual step power factor correction,

built in crossover to set HPF & LPF Filters

Approved Makes: OHM /British Acoustics/ Bose/ British Acoustics

Supply, Installation, Testing & Commissioning of Software Controlled Digital DSP

with below Specifications:-

Number of Inputs - 4,

Number of Outputs - 8,

Input Impedance - 12kΩ unbalanced, 24 kΩ balanced 1 Nos 80,000.00 80,000.00

Adjustable Delay - 1 second / input & 1 second / output

Approved Makes: OHM /British Acoustics/ Bose/ British Acoustics

3 Supply of Flying bar for above speakers 2 Nos 20,000.00 40,000.00

Supply of Stage Monitor Supply of Stage monitor 2-way, bi-amp. bass reflex

design, 400+100W rms , 75Hz-16KHz freq resp, 12" woofer, 1"HF driver, 130dB

SPL max, Disp 90°, polyprop molded enclosure . Approved Makes: OHM /British

Acoustics/ Bose/ British Acoustics

Supply of Audio mixer 24 mono mic inputs 4 line inputs Freely assignable faders

and patching Pre/Post selection per input per bus AES in and out Global mode

encoders FaderGlow™ GEQ on every bus 20 sub-group / aux busses 4 FX busses

5 8 Matrix busses LR and C Mix busses 4 Stereo Lexicon Effects engines Delay on 1 No. 86,000.00 86,000.00

inputs and outputs 4 Mute Groups Freely assignable insert loops Harman HiQnet

integration Colour touch screen interface Approved Makes: (Si Expersion-

2)(Allen Heath QU 24)/ (OSL CX24.4)

6 Supply of Corded microphone (Shure-SM58/OSL/sennheiser) 2 Nos 9,154.00 18,308.00

7 Supply of Instrument Microphone(Shure-57/OSL/sennheiser) 2 Nos 9,678.00 19,356.00

8 Supply of Podium Microphone (Shure/OSL/AKG) 2 Nos 28,411.00 56,822.00

9 Supply of Microphone Stand Big(GS) 2 Nos 1,124.00 2,248.00

10 Supply of Microphone Stand Small(GS) 2 Nos 843.00 1,686.00

Digitally signed by PRIYA

Description of Item Qty. Unit Rate Amount

Supply of microphone cable from stage to control room for microphone points

with conduit pipe etc. (Belden/Klotz/Netmas)

12 Supply of Speaker 2.5sqmm x3core (Belden/Klotz/Netmas) 200 Mtr 100.00 20,000.00

Supply of microphone connecting box made out from CRC sheet metal box duly

13 powder coated paint,with 6 nos XLR panel mounting socket & phono socket 4 Nos 6,322.00 25,288.00

having the facility to connect the 6nos microphone channel.

14 Supply of Professional Head phone(German Meastro/Sennheiser/OSL) 1 Nos 7,170.00 7,170.00

15 Supply of Microphone cable XLR to XLR up to 10 Mtr (Belden/Klotz/Netmas) 15 Nos 1,265.00 18,975.00

16 Supply of Microphone cable XLR to XLR up to 15 Mtr (Belden/Klotz/Netmas) 15 Nos 1,861.00 27,915.00

17 Supply of Speaker connectin connector & MCB Box for Speaker etc 1 Lot 20,000.00 20,000.00

18 Installation charges 1 Job. 80,000.00 80,000.00

Digitally signed by PRIYA