RENOVATION/IMPROVEMENT OF SNCO,s MESS UNDER GE (AF) BAMRAULI

Amount

Taking down cement plaster on brick or stone walls, etc, incl raking out joints, hacking for key, scrubbing down with water, etc & prepare to receive new plaster complete all as specified and directed

M&L for 15mm thick rendering in CM 1:6 on fair faces of brick work, surfaces finished even and fair without using extra cement complete all as specified and directed

M&L for 15mm thick rendering in CM 1:4 on fair faces of brick work, with mixing WPC @ 3% by wt of cement surfaces finished even and fair without using extra cement complete all as specified and directed

M&L for rendering 5mm thick in CM 1:3 finished even and smooth with out using extra cement in ceiling complete all as specified and directed

M&L for preparing new plaster surfaces of ceiling and applying two coats of oil bound distemper over coat of 1.5 mm thick wall care putty complete all as specified and directed.

M&L for preparation of new plaster surfaces of walls and applying two coats of oil bound distemper over a 1.5 mm wall care putty complete all as specified and directed by Engg-in-Charge.

M&L for applying two coats of 100% premium acrylic emulsion paint having VOC less than 50gm / liter and UV resistance as per IS15489:2004, Alkali & fungal resistance dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre /10sqm over and including priming coat of exterior primer applied @0.90 litre/10 sqm over new plaster surfaces of walls complete all as specified and directed.

M&L for complete removing existing treatment on wall surface and applying two coats of oil bound distemper overover a 1.5 mm wall care putty complete all as specified and directed by Enginer-in-Charge.

M&L for complete removal of existing treatment on ceiling surface and applying two coat of oil bound distemper over a coat of 1.5 mm wall care putty complete all as specified and directed.

M&L for complete removal of existing treatment and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50gm / liter and UV resistance as per IS15489:2004, Alkali & fungal resistance dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre /10sqm over and including priming coat of exterior primer applied @0.90 litre/10 sqm over old surfaces of walls complete all as specified and directed.

M & L for Preparation of old painted steel surfaces of any description, over 10 cm width or girth and applying one coat of synthetic enamel paint (ordinary tint), complete all as specified and directed.

M & L for preparation of old wooden Surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F stainless steel (Oil & grease trap consisting of stainless steel 304 grade material having wall thickness of 1.5 mm thickness of size 1.5 m X .90 m X .90 m and the edge shall be mouded including complete fitting polishing complete as per manufracture instruction as approved by GE andcomplete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors aprons etc including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for 18-20mm thick granite work table rubbed and polished for wall lining /kitchen platform over 12mm thick cement mortar 1:3 thick and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M&L for 18- 20mm thick granite Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white ement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

Dismentling of floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed.

M&L for machine cut Kota stone slab 20 to 25mm mm thick in treads, landings of stair case over cement screed bed laid and jointed wilth grey cement slurry mixed with pigment to match the shade of the slab lincluding & grinding polishing over and including screedbed 20mm thick in cm 1:6 complete all as spd & directed.

M & L for machine cut Kota stone slab as in skirting, risers 20 to 25 mm thick, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing with mirror polish granite finish including backing coat 10 mm thick in cm1:3 complete all as specified and directed.

M&L for Non Skid ceramic coloured tiles 7 to 8 mm thick joint free (square/ rectagular) area of each tile exceeding 0.06 sq m but not exceeding 0.11 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile and laid over and inclduing 15mm thick screed bed layer in CM (1:6) complete all as specified and directed.

M&L for Glazed ceramic tiles in vertical surface 450x 300x7 mm thick joint less tiles set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade tile over and inclduing 10mm thick rendering in CM (1:4) complete etc. (1st quality/Premium Quality).complete all as specified and directed.

M&L for Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match in floor etc set and jointed in neat cement slurry and pointed in white as coloured cement to match over and including 15mm thick screed bed in cement mortor (1:6) complete all as specified and directed

Taking down chowkats with shutters not exceeding 1.5 Sqm each (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking of shutters from the frames) exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as specified and directed.

S&F for Pressed steel frames of size 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.

S&F for Pressed steel frames of size 105mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.

M & L for Solid PVC Frame for door,kitchen cabinet,cupboard of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed.

S&F Second class hardwood glazed and skeleton door shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc complete all as specified and directed.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples etc complete all as specified and directed.

S&F Second class hardwood Flush shutters 35mm thick, solid core construction, with block board core & plywood face panels , commercial type with mica on both sides complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) both side prelam pvc sheet of decortive choice consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.complete all as specified and directed.

S&F powder coated anodised aluminium (sliding/ hanging/ fixed type) ventilator with frame size 60x40x2.00mm thick and shutter with section bearing bottom 25x18x1.50, top 39.4x17.7 X1.50 mm ( suitable for moving over two track or fixed over top of frame work , top and side section of size 61.6 x 31.75x1.5mm and bearing bottom track of size 61.6x 31.75x1.5mm or fixing with hinges including necessary aluminium jointing cleats, glazing cleats, rubber packing anodised snape beading, screws etc with 5mm thick sun control plain glass in panels incl all fitting and fixture complete all as spesified and directed

Supply & fixing power coating anodised aluminium glass partion wall with frame size 101.60 x 44.45 x 2.00 mm thick and shutter aluminium anodised an top rail 47.62 x 44.45 x 1.50mm and style 47.5 x 44.5 x 1.50 mm lock rail 83.5 x 44.45 x1.50mm and bottom rail 150.00 x 44.50 x 2.50 mm with 5.mm thick plain glass including lock and necessary fitting and fixture complete all as specified and directed.

M&L for power coated anodised aluminium doors (sliding/ hanging type) with frame size 101.60 x 44.45 x 2.00 mm thick and shutter aluminium anodised and top rail 47.62 x 44.45 x 1.50 mm style 47.5 x 44.5x1.5mm, lock rail 83.50 x 44.45 x 1.50 mm and bottom rail 150.00 x 44.50 x 2.50 mm including necessary aluminium fittings like aluminium butt hinges 04 Nos, aluminium handle 150mm 02 Nos, aluminium tower bolts 200 mm 01 No, aluminium door stopper 01 Nos, jointing cleats glazing cleats, rubber packing, anodised aluminium shape beading screws etc with panelling in two parts with 12mm thick prelaminted particle board in lower panel and 5mm thick tinted glass in upper panels including all fittings & fixture complete all as specified and directed.

Dismantling of asbestos cement (corrugated, semicorrugated , etc) sheet in roof covering all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering or fixed to wall with self tapping screws complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description

M&L for Framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0. complete all as spesified and directed .

M&L for preparing new or previously untreated surfaces of wood or wood based materials of any description exc 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparing new or previously untreated steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 using 12.5 mm granted stone aggregate as hold fast/filling in pressed steel frame complete all as specified and directed

S&F 100mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin,anodised and fixed, type B-21 complete all as spesified and directed .

S&F 300 mm long Aluminium alloy with dia 16mm, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy.complete all as spesified and directed .

S&F 250 mm long Aluminium alloy with dia 16mm, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy.complete all as spesified and directed .

S & F 125 mm long Extruded Aluminium alloy handles, fabricated type, anodised.complete all as spesified and directed .

S & F 200 mm long Aluminium anodised barrel tower bolts of extruded section.complete all as spesified and directed .

S&F for 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as spesified and directed .

S&F for 150mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as spesified and directed .

S&F 18mm thick green panel water resistant board(HDHMR Board) minimum 600 Kg/Cum density grade 1 quality one side pre-laminated with mica and other side plain to make kitchen cabinet/drawer shutters fixed with screws, solvent cement/adhesive and parliyament hinge as requred as per manufacturer instructions complete as per specifications and as directed by the Engineer-in-Charge. Note:- (i) Quoted rates deem to be include Cup board accessories ie fittings, handles, hinges,magnate etc . (ii) Quoted rates deem to be include fixing of cabinet on wall with appropriate rawl plug/ dash through fastener (hammer type). (iii) Fabrication and installation of cabinet to be carried out by authorised vendor of manufacturer only.

S&F 18mm thick green panel water resistant board (HDHMR Board) minimum 600 Kg/Cum density grade 1 quality of both side plain rigidlam glossy finish fixed with screws, solvent cement/adhesive as per manufacturer instructions to make kitchen cabinet sides top and bottom and shelves inside the cabinet complete as per specifications and as directed by the Engineer-in-Charge. Note:- (i) Quoted rates deem to be include Cup board accessories ie fittings, handles, hinges,magnate etc (ii) Quoted rates deem to be include fixing of cabinet on wall with appropriate rawl plug/ dash through fastener (hammer type). (iii) Fabrication and installation of cabinet to be carried out by authorised vendor of manufacturer only.

S&F in repair fancy type decorated Stainless Steel curtain hanging rods 20 mm dia,and fixed to stainless steel bracket for hanging curtain complete all as specified and directed.

S&F Stainless Steel brackets having screw for tighting of curtain rod of 20mm dia for fixing of curtain rod, complete all as specified and directed.

S & F Stainless Steel bright color decorative corner/end cap for Curtain rod complete all as secified and directed.

S&F stainless steel peg set of six with base plate and fixed to wall/door with rawal pugs/ s/s screw all as specified and directed.

S&F shelf of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 300gms) complete all as specified and directed .

S&F in repair CP vitreous china soap dish fancy type complete all as specifed and directed.

S&F in repair Brass chromium plated, tubular towel rails 20 mm dia, D- type, 60 cm long between flanges, completed all as specified and directed.

S&F in repair brass chromium plated shower roses with swivel joints, 125 mm size in square with CP long shank arm including fixing to steel pipe or union, complete all as specified and as directed.

S&F in repair sink with 3 tier washing way system made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste; including all accessories overall size 1828.8mm x 609.60mm x 812.8 mm each bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F Vitreous china wash down water closet pan (pedestal pattern) white (excluding flushing cistern and flush pipe) and including fixing of the following components viz. pedestal pan with "P" or "S" trap, seat and cover for pedestal pan, flushing cistern, brackets, chain and pull or lever handle, flushing pipe including jointing to socket of flushing rim and connecting pipe to union of flushing cistern, inlet and overflow pipe, anti-syphonage pipe or stopper fixed as in repairs complete all as specified and as directed. Note:- Flushing cistern and flush pipe as required shall be measured and paid for under supply only separately.

S&F HEALTH FAUCET (ABS body) mild steel chrominium plated suitable for 15mm dia pipe with 1.25 mtr long flexible tube and ABS wall hook including making fixed in position complete all as specified and directed. as in repairs complete all as specified and as directed.

S&F in repairs PVC flushing cistern 10 ltr capacity valve less syphonic action type low level with and including dual flush ball valve float & handle, waste pipe & brackets complete set complete all as specified and directed.

S & F in repair Vitreous China wash basin, flat back, size 450x300mm white, excluding taps, waste, chain and plug and porcelain stopper but including brackets.

S&F in repair Waste coupling of PTMT (half or full threaded) . (Minimum weight 2mm45gms/40mm 60 gms waste pipe of 40mm dia suitable for WHB, kitchen sink complete all as specifed and directed

S&F in repair angle cock fancy type CP with long shank cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends of size 15mm bore. complete all as specified and directed.

S&F in repairs bib tap, cast copper alloy with capstan head, CP fancy type with long body shank, screwed down with high pressure screwed for iron pipe & fixed 15mm bore, complete all as specified and directed.

S & F in repair Pillar taps fancy type cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed

S&F in repair PVC connections 15mm size with PTMT nuts of length 600 mm, complete all as specified and as directed.

Dismantling tanks water tank exc 250 but n exc 500 ltr.complete all as specified and directed.

S&F rotational moulded polythene water storage tank of capacity 500 ltrs (Cylindrical/vertical with closed top), triple layer construction, ISI marked, hoisted & fixed in position including over flow 450mm, waste pipe 600mm long with fitting etc. of 20 mm dia directed complete all as specified and as directed.

S&F ball/ float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed 20mm bore minimum weight 210 gms complete all as specified and as directed.

S& F Stop valves/Gate valves 25 mm dia cast copper alloy,screwed down, high pressure with crutch or butterfly handel, screwed both ends for iron pipe or for unions and fixed.complete all as specified and directed.

Taking up or down old steel tubing 15 mm dia complete all as specified and directed.

Taking up or down old steel tubing 20 mm dia complete all as specified and directed.

S&F 15 mm GI tubes medium grade with all fitting and fixed complete to walls, ceilings or laid in floors including taking up or down old steel tube complete all as specified and directed.

S&F 20 mm GI tubes medium grade with all fitting and fixed complete to walls, ceilings or laid in floors including taking up or down old steel tube complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories).

S & F of 110 mm dia(SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed

S & F of 75 mm dia(SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed

S&F PVC SWR (110) bends any radius comlete all as specified and directed.

S&F 75 mm PVC (SWR) junction single, (singl T ) (equal or unequal ), ordinary or inverted ( spigot or socket type ) or with paralle oval access doors branches .complete all as specified and directed.

M&L for 75mm PVC (SWR)floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

M&L for PVC(SWR) gully trap 125/110mm setting and jointing with solvent cement complete all as specified directed.

Demolition of brick work or stone boulder masonry, built in cement mortar including all quoins, arches, pillars, etc., but excluding ashlar facings, dressed stonework and precast concrete articles all as specified and as directed.

M&L for Brick work with subclass "B" bricks, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6 of using class designation 100 of bricks in lieu of 75 all as specified and as directed.

Demolition to reinforced cement concrete of roofs, floors (other than ground floors) beams staircases,landing,chajjas, cover and similar suspended work complete all as specified and directed.

M&L for frame work to soffits and suspended slabs such as roof slabs floor slabs landings and similar work not exceeding 200mm thick (horizontal or sloping )

S&F Mild steel round bars 8mm dia and over, cut to length, bent to shape required, including ranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips Fe-410-W (Gde.E-250)Part- I quality-A or Fe 290 (Gde -E-165

M&L for Pre-cast cement concrete type B-1 (1:2:4) (using 20mm graded aggregate) as in drain cover slabs set in cement mortar 1:6 including necessary formwork complete all as specified and directed.

M& L for providing and injecting chemical emulsion for post construction Herbicides Treatment along wall complete all the complete all as specified & directed.

S&F 1.2 mm thick stainless stell sheet ( grade 304 ) for wall cladding, fixed on SS hollow tube frame 1.5 mm thick , fixed on wall as per manufacture instructions for wall cladding ,complete as per specifications and as directed by the Engineer-in-Charge. Note:- (i) Quoted rates deem to be include fixing of frame on wall with appropriate rawl plug/ dash through fastener (hammer type). (ii) Quoted rates deem to be include fixing of SS sheet for wall cladding on frame and also including welding, grinding, buffing, polishing and making curvature (where ever required) (iii) SS frame for wall cladding,shall be measured and paid separately under respective item of this schedule.

S&F providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary ccessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement.

Taking down carefully aluminium batten point, wiring for light/fan/socket/bell or power point including. All fittings i.e. switch, sockets, ceiling rose, regulators, batten holders, etc. Complete and making good disturbed surfaces of wall/floor to match with the surroundings of wall/ceiling/floor etc including taking down old light fittings. Note :- (i) Contractors quoted rate of this item deemed inclusive of unscrewing of the serviceable fittings and fixture as directed and deposit in MES store yard. (ii) Quoted rate also deem to be included cost of cutting chases for taking out concealed conduit and nitch for terminal box. (iii) Decision of GE shall be final and binding in respect of serviceability of fittings/fixture.

M & L for Point wiring complete with 1.5 sqmm single core PVC insulated FRLS cable 1100 volts grade with multi stranded copper conductor drawn through new PVC concealed conduit mediem grade, ISI marked and including provision of 1.5 sqmm PVC insulated copper cable FRLS as earth continuty, fabricated branded modular metal flush box duly make embossed, concealed in walls with suitable modular inner and outer plate for housing switches , socket outlet and fan regulators etc, complete all as specified and as directed for the followings:-

(a) One light/fan/bellpoint controlled by one switch single pole one way

(b) All as per item No 96 here-in-before but one 3 pin 6 amp switch socket out let independent .

(c) All as per item No 96 here inbefore but one 3 pin 6 amps socket outlet on the same board with other switch complete .

All as per item No 96 here-in-before but using 02 Nos. 4.0 sq mm size for main cable and 01 No.2.5 sq mm size as earth conductor for one 16 Amp switch socket outlet on independent board.

Supply and fix switch modular flush 10A single pole one way ISI marked

Supply and fix modular sockets 10 Amp 2 in 1 2/3 pin combined all as specified and directed.

Supply and fix switch modular flush type 15/16 Amp single pole one way 240 volt one module ISI marked

Supply and fix modular sockets 16 Amp 2 in 1 3/5 pin combined all as specified and directed.

Supply and fix ceiling rose surface bakelite 60x25mm three terminal

S&F Modular Fan step regulator, 120W - 2 module complete all as specified and directed.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

S&F LED batten extruded surface mounting fitting 2 feet long aluminium housing 10 watt input voltage 220 volt inbuilt LED and driver complete all as specified and as directed.

Supply and fix flood light for building illumination 30 watt 240 volt 50 Htz 6500K 120 lumen/watt IP-65 protection complete all as specified and directed.

Supply and fixing Ventilating Fan 250 mm sweep, 1250 RPM, non metallic resin body, single phase 240 volts AC 50 Hz and connecting up complete including louvers and provision of making holes and copper cable 3 core of size 0.5 sqmm for connection from ceiling rose to fan complete all as specified and as directed.

Supply and fix exhaust fan 450 mm sweep metalic body copper bound including fixing and louver shutter 240 volt 50 Htz. complete all as specified and directed.

Supply and fix exhaust fan 300 mm sweep metalic body copper bound including fixing and louver shutter 240 volt 50 Htz. complete all as specified and directed.

Supply and fix wall mounted fan 400mm, 230 volts, 50 Hz 1420 RPM with 90 degree oscillation and having speed control by two pull cord system all as specified and directed.

M&L for taking down carefully existing ceiling fan/exhaust fan from site before B/R repair work, keeping in safe custody in store for greasing / oiling of ball bearings / bushes and making it for smooth and noise free operation and painting with Hi-Gloss synthetic enamel paint of approved shade by spray painting after filling cavities' and re-fixing after providing new fan clamp, nuts/bolts, washers, down rod as required and provision of 3 core copper flexible cable of size 1.0 Sqmm from ceiling rose to fan connector complete with writing of MES No. on the fan surface all as specified and directed.

Supply and fixing ceiling fans Robust and reliable inverter motor (brush less DC Motor with remote powered by ECM technology, BEE 5 star rating for energy saving, AC single phase 230/240 V of size 1200 mm sweep including making connection with three core flexible, copper cable pvc insulated of suitable length incl taking down old & deposited to MES store yard complete all as spd & directed. Note : Cost of remote & remote cell included in this item

S & F sheet metal enclosure with socket and plug top and MCB single pole and neutral enclosure with two Pin and earth plug and socket complete with one single pole MCB, 240 V, 25 Amp.

S & F triple pole and earth enclosure with a three pin and earth plug with socket complete with one triple Pole MCB 415 Volt 32A.

Supply ,fixing and texting Industrial commercial chimney comprising following sizes hood, motor and ducting system :- (1) 9' x 2.8' (LXB)-01 Hood (2) 6' x 2.8' (LXB)-01 Hood (3) Turboforce 5 HP Motor -01 (make : Crompton) (4) Double counted ducting system-40 feet (Approx) Specification for hoot : SS 304 JINDAL/JSL stailess steel will be used to make the Hood. The hood comes with double filter absorbes maximum smoke and after processing abstract carbon dioxide release corbon dioxide free air outside. The hoot comes with 5 years warranty , no rusting grade steel and atomatic sensor. Specification for motor : Automatic mode changer. bird screen for protection against birds & foreign material. Rust proof body & blade for durability. Automatic shutter function. Stedy metal body with blades. 03 Years Warranty Ducting system specification : TATA autorised double coated high grade material is used. five years warranty is included. High quality beding with precession. High thick material is used. The creation duct will be done in work place. Note : Taking down old and deposited to MES store rate included this.

Supply & fix MCB DB SPN 4 way, double door, IP-43, IK-09, Isolated Neutral Bar and fixed flush to wall and suitable for universal mounting complete all as specified and directed.

Supply & fix MCB DB SPN 8 way, double door, IP-43, IK-09, Isolated Neutral Bar and fixed flush to wall and suitable for universal mounting complete all as specified and directed.

Supply & fix MCB DB SPN 12 way, double door, IP-43, IK-09, Isolated Neutral Bar and fixed flush to wall and suitable for universal mounting complete all as specified and directed.

Supply and fix MCB, single pole and neutral, 230 volts, 32 Amp rating, 'C' series fixed in DBs catered here-in-before.

Supply and fix MCB, single pole and neutral, 230 volts, 40 to 63 Amp rating, 'C' series fixed in DBs catered here-in-before.

Supply and fix MCB SP 6-32 Amps 240 volts 10 KA 50 HZ 'C' curve complete all as specified and directed by Engineer in charge

M&L for taking down carefully existing geyser of any type and cap from site before B/R repair work, keeping in safe custody in store for servicing and painting with Hi-Gloss synthetic enamel paint of approved shade by spray painting after filling cavities, writing of MES No. and re-fixing with new hot and cold water connection as required incl provision of 3 core copper flexible cable of size 2.5 Sqmm complete with 15 Amps 3-pin plug top all as specified and directed.

S & F water heater storage type (Geyser) vertical type with suitable size of fastner and incl provision and connecting up of SS braided pipe suitable size with adopter for inlet and outlet water connection having adjustable knob for temperature control and inner tank should be glass line coated complete all as specified of capacity 25 ltrs having element 1.5/2 KW BEE star rating incl taking down old and deposted to MES store yard

S&F Sub main wiring with 3 run of single core PVC insulated and PVC Unsheathed, multistranded copper condutor of nominal area 6 sqmm FRLS, 1100 Volts grade cable drawn into and including rigid non metalic PVC Conduit of including all fittings and one run of PVC insulated and PVC unsheathed, multistranded copper conductor of nominal area 6 sqmm FRLS 1100 volts grade cable continuous earth wire of green colour code complete. Note:- (a) Three runs of 6 sqmm cable and one run of 6 Sqmm cable as earth lead with conduit shall be measured as one unit length for payment. (b) Quoted rate shall deem to be included cost of cutting chasses in wall for concealling conduit and making good to match with existing finish.

S&F Sub main wiring with 2 run of single core PVC insulated and PVC Unsheathed, multistranded copper condutor of nominal area 6 sqmm FRLS, 1100 Volts grade cable drawn into and including rigid non metalic PVC Conduit of including all fittings and one run of PVC insulated and PVC unsheathed, multistranded copper conductor of nominal area 6 sqmm FRLS 1100 volts grade cable continuous earth wire of green colour code complete. Note:- (a) Two runs of 6 sqmm cable and one run of 6 Sqmm cable as earth lead with conduit shall be measured as one unit length for payment. (b) Quoted rate shall deem to be included cost of cutting chasses in wall for concealling conduit and making good to match with existing finish.

S&F Sub main wiring with 2 run of single core PVC insulated and PVC Unsheathed, multistranded copper condutor of nominal area 4 sqmm FRLS, 1100 Volts grade cable drawn into and including rigid non metalic PVC Conduit of including all fittings and one run of PVC insulated and PVC unsheathed, multistranded copper conductor of nominal area 4 sqmm FRLS 1100 volts grade cable continuous earth wire of green colour code complete. Note:- (a) Two runs of 4 sqmm cable and one run of 4 Sqmm cable as earth lead with conduit shall be measured as one unit length for payment. (b) Quoted rate shall deem to be included cost of cutting chasses in wall for concealling conduit and making good to match with existing finish.

Supply & fix in repair factory made epoxy powder coated Load line Distribution Board TPN-4 ways with metal door (IP-43 protection) fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including insulated 200 Amp copper bus bar, Isolated neutral bar, standard DIN rail, Earth bar and cable ties for cable management, top and bottom removeable gland plates with knockouts and suitable for one TPN- MCCB any capacity as incomer and 6 to 63 Amp SP MCBs outgoing complete all as specified and conforming to IS : 8623.

Supply and fix in repair MCCB 100 Amps, FP 415 volts 16 KA 50 HZ with thermal magnetic setting complete all as specified and directed by Engineer in charge.

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick, buried directly in to ground ( earth pit) not less than 2.25 metres deep below GL with top edge of earth plate opt less attn. 1.50 m below ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate, connected to GI lead wire of 4 mm dia.(7.50 m Long) by means of nuts, bolts and washers, check nuts of GI and protected by the GI pipe light grade 15 mm nominal bore(7.5 m long) for earth lead wire and watering pipe light grade of 20 mm nominal bore, 0.63 mm thick G I sheet funnel , wire mesh, earthing test point etc complete including necessary earth work and excavation in any type of soil , PCC 1:2:4 type B1 earth pit and Precast RCC cover 65 mm thick duly reinforced with 6 mm dia. MS round bars @ 100mm C/C both ways, with 10mm dia MS round bar as in lifting handles, excavation, earth work including laying the GI pipe concealed in floor/wall all as described in electric plate of SI Part I complete all as specified and directed and testing on completion. Note :- If the desired earth resistance is not found, earthing shall be redone by the contractor at no extra cost to the department.

Material, labour jointing & testing XLPE insulated armoured heavy duty electric cable with standard aluminium conductor, 1100 volts grade, cross-sectional area 35 Sqmm 3.5 core including making connection with suitable size of cable gland, aluminium lugs etc complete including taking down old U/S cable all as specified and directed.

Supply and fix LED 2 X 2 ft backlite surface mounted fitting 36 Watts not less than 3200lm with Metallic CRCA powder coated body with high efficiency opal/PMMA diffuser with system efficacy > 80 lm/W, CRI>80, color temperature >5700k, IP 20, Power factor<0.95, THD<10%, 50000 burning hours , Ambient temperature 0 to 500 DegC, Driver should meet IEC complaint for safety, with voltage variation range of 150-270 V and surge protection of 2.5 KV including necessary fixing arrangementsfixed complete all as specified and directed.

Excavation in trenches in soft/loose soil n. exc 1.5 Mtr wide and not exc. 1.5 M deep and getting out including forming bottom surface for laying of pipes complete all as specified and directed.

Returning filling in including spreading, leveling, watering and well ramming in layers not exc 25 mm thick complete all as specified and directed.

Removal of excavated material to a distance not exc 50 Meter and depositing where directed at a level not exc 1.5 M above the starting point complete all as specified and directed.

Supplying, laying and cushioning for cable protection in trenches 8 cm deep before laying cable and 15 cm deep over the cable including well punning complete all as specified and dierected

Supplying, laying sub class 'B' bricks old size with axis of the bricks perpendicular to the axis of the cable as in cable protection complete all as specified and directed.

Supply & Fixing in replacement GI tubing light grade in trenches/fixed to wall/ceiling including required GI fitting of size 40mm dia complete all as specified and directed

M&L for complete removal of existing finishes on wall and applying two coats of plastic enamel paint over a coat of primer including chalk whitning with spray painting machine complete all as specified and directed.

M&L for 5 mm thick looking mirror with LED touch lighting hanging in brackets with decorative finish complete all as specified and directed

S&F drapery rod 19mm inner dia (wall thickness not less than 1.60mm) stainless steel fancy type bracket fixed with rawl plug or screws on wall/beam and shall be provided with fancy finial at ends as approved by Garrison Engineer complete all as specified and directed. Note :- (i) Drapery rod Cat part no- SW-06 of vista or equivalent model of make as specified in Appendix "B" to particular specification.

S&F in curtain brackets stainless steel with matching with the curtain rod complete all as specified and directed.Note :- (i) Drapery rod Cat part no- SW-06 of vista or equivalent model of make as specified in Appendix "B" to particular specification.

M & L cutting chases for concealed water tubing, pinning in, making good of facings where required and pointing in cement mortar 1:3 to ends or edges etc, cutting not exceeding 10 cm width or girth, complete.

Supply only autoclosing hydrolic (soft closing) chrome finish stainless steel frog hinge openable at 110 degree complete.

Supply only 100mm long stainless steel (grade S-304) handle fancy type polished bright chrome finish complete.

S&F in repair Aquisense Sensor Faucet for Wash basin with base flange Cat Part No - SNR-CHR-51011 with all kit and assebly complete all as specified and directed.

S&F chromium plated towel rack fixed with wall complete all as specified and directed.

S&F in repair fancy type glass corner shelf with CP brackets etc complete all as specifed and directed.

S& F in repair CP fancy type toilet paper holder complete all as specified and directed.

S&F in repair PVC waste pipe of 32mm dia suitable for WHB, kitchen sink complete all as specifed and directed

S&F in repair stop valve brass chromium plated fancy type 15mm bore with wall flange of authentic single lever for iron pipe or for unions complete all as specified and directed.

S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 120mm (minimum) wide with chromium plated brass bracket guard and railing 600mm long complete.

S&F in repairs 125mm dia CP grating etc complete.

Demolition of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.

Providing & fixing false ceiling at all height with GRG (Glass Fibre reinforced Gypsum) false ceiling tile of size 595x595mm of approved texture, design and pattern having moisture content less than 2%, humidity resistance of 99%,NRCO.50 to 0.75 as per IS 8225:1987, non combustible as per BS 476(Part4)-1970 and light reflectance of 85% (minimium) to be laid in true horizontal level suspended on interlocking metal T-grid of hot dripped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per Sqm including both sides) comprising of main T-runner of size 15x32mm of length 1200mm and sectinally intermediate cross T of size 15x32mm of length 600mm to form grid module of size 600mmx600mm, suspended from ceiling using galvanised mild steel items (galvanised @80 grams per Sqm) i.e. 50mm long,8mm outer diameter M-6 dash fastners 6mm dia fully threaded hanger rod upto 1000mm length and L- shape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x24x0.40mm of length 3000mm to be fixed on periphery wall/ partition with the help of plastic rawl plugs at 450mm centre to centre and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per direction of the Engineer in Charge

Note :- Credit shown in credit schedule of tender document shall be considered by the tenderer while quoting the rates of various items of this schedule. The same shall be recovered from various payment to contractor before handing over old material.

HIMANSHU TRADERS

M.R. ENTERPRISES

Aditi Construction Company

M/S SATISH KUMAR

M/S Rakesh Singh