PROVIDING TACTILE FLOORING HAND RAIL FOR STAIRSRAMPS AND SIGN BOARDS ETC FOR PERSON WITH DISABILTY IN JUDICIAL COURT COMPLEX AT GARHSHANKAR DISTRICT HOSHIARPUR

Cutting of floor topping of concrete / Kota Stone /any kind of marble/ tile floor depth up to 50mm any kind of marble/ tile floor depth up to 50mm due care so that surrounding floor should no damage) to lay the tactile flooring 300mm wide including cost of providing and laying 25mm CSR 14.160

Providing and Laying Tactile Flooring full body vitrified , low water absorption below 5%, having excellent slip resistance , very dense, durable and abrasion resistant, solid through colour, fade proof, highly chemical and stain resistance unglazed finish porcelain tile of size 300mm x 300mm x 10mm + 5mm thick, approved profile design, Tec-button/Tec-liner laid in ordinary grey cement and on 20mm thick bed of cement mortar 1:3 filling neat cement slurry between joints with White Cement containing pigment to match the shade complete in all respect. (Tile design and pattern will be as per guidelines issued for persons with disability) CSR 14.116

Providing and fixing 16 gauge stainless steel pipe of various sizes railing of grade 304 dully fixid on side wall with the help of bolts fixid with hand rail s.s square bar 25X25mm welded to MS flat 50X5mm complete in all respect as per as per specification and entire satisfaction of Engineer in Charge. (Railing along wall in ramp for ground floor to upper storey design as per guidelines issued for persons with disability) Length of the railing on both side of the ramp 50mm dia CSR 18.39

Providing & Fixing in position C.P. Brass flange Dome of approved make (to the approval of Engineer-in-charge ) under various fixtures complete in all respect. CSR 30.64a

Providing and Installation of Safety signage as per guideline for person with disability made of retro reflective sheeting as per colour specified and writing matter will be of same material in white fixed / pasted over 4mm thick aluminum composite sheet, including cost of writing matter with braille also firmly fixed on wall with nylon fastener, brass screw and washer complete as per specification and as desired by engineer in charge CSR 18.57

nfomatory sign board 800X600mm rectangular with high intensity microprismatic grade retrorelective sheeting type XI as per ASTM D 4956-09 fixid over 4mm thick alluminium composite material (ACM) sheeting having alluminium skin thickness of 0.4 to 0.5mm on both sided and fixing the same with suitable size alluminum alloy rivets @200mm c/c to back support frame of 25X25X3mm angle iron supportd on a mild steel angle iron post 65X65X6mm with cost of definition plate firmly fixid to ground in foundation concrete M25 of size 0.45X0.45X0.6M FOR vertical post complete as per specification CSR 24.46a

Providing and Installation of Safety signage as per guideline for person with disability made of retro reflective sheeting as per colour specified and writing matter will be of same material in white fixed / pasted over 4mm thick aluminum composite sheet, including cost of writing matter with braille also firmly fixed on wall with nylon fastener, brass screw and washer complete as per specification and as desired by engineer in charge. CSR 18.57

MS Pipe for Fixing Board as Per AC Slip Chapter No. 3

Earth work in excavation in foundations trenches etc. in all kinds of soil where Pick-Jumper work is not involved and not exceeding 2.0 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil clear from the edge of excavation and subsequent filling around masonry in 15 cm, layers with compaction including disposal of all surplus soil as directed within lead of 30 metres. CSR 6.6

Cement concrete 1:8:16 with stone aggregate 40mm gauge CSR 10.6b

Cement concrete 1:2:4 with stone ballast or shingle using conc mixing volumetric type

First class burnt brick work laid in cement sand mortar 1:5 in foundation and plinth CSR 11.5

Reception Table L-Type size :The structure made of 18 mm 710 BWP PLY (BWP / Marine-grade preferred) on which 1 MM thick Laminate (teak / oak / beech) for premium finish the structure size Length 6 feet (1830mm) x Depth (Front to Back): 3 feet (900 mm). The structure should have one drawer with telescopic channel and one cabinet with English hinges. There should be proper locking system. The edges of the structure should be polished in all respects.

Supplying & Placing Visitor Chair ergonomically designed for user comfort & shall have aesthetically appealing design. The seat shall be made of 15mm thick hot pressed malaysian plywood with HR polyurethane foam 50mm thick having density 40kg/m³ upholstered with lathearite in black colour with 0.8mm thick and 535 GSM and the back shall be made of double layered moulded hot pressed Malaysian plywood (12+6)mm thick with HR polyurethane foam 30mm thick having density 32kg/m³ upholstered with leatherite in black colour with 0.8mm thick and 535 GSM. The frame shall be cantilever support made up of MS CRCA chrome plated round pipe of Dia 25 mm with 1.6mm thick. There shall be PPCP shoe provided at the base to avoid scratches on the floor . The Seat size shall be 475±10mm(W) X 490±10mm(D) and back size shall be 470±10mm(H) from seat & overall height =930±10mm

Electric Wheelchair Has Both Manual & Power Functions And The Joystick Or Controller Can Be Inter Changeable That Can Change From Left To Right And Right To Left, 360 Degrees Free-Direction Turning, Easy To Operate. This Electric Wheel Chair Is Portable With Folding Structure Removable Battery Box For Convenient Recharging , Flip Up Armrest, Adjustable And Detachable Footrest, Rear Wheels Driven By Two Motors. This Is Propelled By Electric Motor Rather Than Manual Power. 12 AH Battery Gives More Storage Power And Can Use More Time. Height Between Seat And Ground 48 Cm, Intelligent Joystick, 20 AH, Metal Paint, Motor 250 W X 2 Pcs, Rear Wheel 12″ Front Wheel 8″

Wheel Chair Has A Length Of 42” (106.7 Cm), A Height Of 36” (91.4 Cm), Seat Heights Around 19.5” (49.5 Cm), And A Width Of 25” (63.5 Cm). Wheelchairs Are Wheels Designed To Serve Users That Are Unable. The Wheel Chair Should Be Foldable And Smooth Running .

Providing and Laying Out Door Precast Designer chequered tiles of any size & any shape 25mm thickness having top layer of white cement mixed with pigment, laid on 20mm thick bed of ordinary cement mortar 1:3(1 ordinary cement :3 fine sand), joints grouted with white cement slurry containing pigment to match the shade complete in all respect as per specifications and to the entire satisfaction of engineer- in- charge. (CSR 14.135)

Three Seater Bench For Public :- Supplying & Placing Three Seater Bench. The Seat And Back Shall Be Made Up Of High Quality Cold Rolled MS Perforated Sheet Of 1.2mm Thick, Pressed And Welded To Form The Shape. The Seat And Back Electrostatically Coated With Epoxy Powder And Then Cured Under Heat To Allow It To Form A Skin. The Armrest Shall Be Made Up Of Mild Steel Powder Coated Tube With 1.2mm Thick. The Base Structure Shall Be Supported By MS Powder Coated With 40-60µ (DFT). There Shall Be PPCP Shoe Provided At The Base To Avoid Scratches On The Floor. The Seat Size Shall Be 440±10 Mm(D) X 405±10 Mm(H) From Ground. Overall Height Shall Be = 775±10 Mm, Overall Depth = 710±10 Mm & Overall Width = 1765±10 Mm.

Steel work in hip and jack rafters, common rafters, purlins etc. with angle iron cleats and other connecting plates complete in all respect. (CSR 18.2)

Steel work, fixed independently without connecting plates, including cutting, hoisting and fixing in position :- (b) Flats

Providing and fixing corrugated G.I. Sheet roofing complete in all respect. CSR 13.8

Painting two coats including priming coat with ready mixed paint for metallic surfaces in all shades on steel or iron work (CSR 16.17+16.20)

Road marking with thermoplastic compund. Road marking with hot applied thermoplastic compound 2.5mm thick including reflectrorising glass beads @0.25kg/sqm area as per IRC 35 1997 complete as per techanical clause 803 of MORTH specification. Csr 24.57

Earth work in excavation in foundations, trenches etc. in all kinds of soils Proposed New Bath Room

P/L Cement Concrete 1:6:12 Proposed New Bath Room

Base course of floor consisting of 100mm thick cement concrete 1:8:16 and 100mm sand filling using mechanical mixer for mixing of material Bath Room

P/LCement concrete 1:2:4 mixing by mechanical means using concrete mixer volumetric type

First class burnt brick work laid in cement sand mortar 1:5 in foundation and plinth. Bathroom Horizontal wall New Step 1/Bathroom Vertical wall New Step 1

First class BB work laid in cement sand mortar 1:5 in superstructure.

20 mm thick cement plaster 1:4

12.5 mm thick cement plaster 1:4

Shuttering for faces of concrete foundations and foundation beam & plinth beam (vertical or battering)

Centering and shuttering for sides and soffits of beam, beams, launching girders, bressumers, lintels

Centering and shuttering for flat surfaces such as suspended floors, roofs, landings, chajjas, shelves etc

Reinforced cement cocrete M-20 mechanicaly batch mixed using batch type mixed using batch type concrete mixer and needle vibrator but excluding steel reinforcement, centering and shuttering in foundation and plinth.

Reinforced cement concrete M-30 mechanically batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in superstructure

Cold twisted deformed (ribbed/ tor steel) Bars Fe 500 grade as per IS 1786-2009 for R.C.C. works, where not included in the complete rate of R.C.C. including bending, binding, and placing in position complete.

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate z sections and other sections conforming to Is: 733 and IS : 1285 of Jindal, Hindalco, Mahavir or equivalent make approved by Engineer in Charge , fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC Plug/neoprene felt etc. aluminum sections shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle, aluminum snap beading for glazing/paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-In- Charge. (Glazing and paneling to be paid for separately) : ( For fixed portion and chawkhats)

For shutters of doors, windows & ventilators including providing and fixing hinges/pivots and labour for fixing of fittings wherever required including the cost of PVC Plug / neoprene gasket required

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in paneling fixed in aluminum doors, windows shutters and partition frames withC.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-In-Charge. Prelaminated particle board with decorative

Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with PVC Plug/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminum snap beading shall be paid in basic item)

Cost of aluminum fittings complete for doors, windows such as tower bolts, handles,Stoppers and screw etc. for these fittings (Excluding sliding bolt) For shutter area above 0.50 sqm

Providing and fixing hydraulic door closer ISI mark with necessary screw etc. complete I.S.I Designation No. III (size of door 851mm to 1000mm)

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for including necessary cutting and making good etc. complete.

Prepration Of Plaster Surface/Deduct Door And Window

Distempering with Acrylic washable oil bound distemper (of approved manufacture) two or more coats over one priming coat to give an even shade

Finishing walls with Premium Acrylic smooth exterior paint with silicon additives of required shade with two or more coats applied @ 1.43litre/10 Sqm over and including base coat of water proofing Cement Paint applied @ 2.20 Kg/10 Sqm

Cement concrete 1:2:4 gola 10cm x 10cm concave quadrant along junction of roofs with parapet wall finished smooth, where specially specified.

Top khurra 0.6m x 0.6m for rain water pipe in 25mm thick cement concrete 1:2:4 over 50mm thick cement concrete 1:8:16.

Providing and fixing in position gratings 150mm x 150mm on top Khura PVC grating

Providing and Laying Out Door Precast Designer chequered tiles of any size & any shape 25mm thickness having top layer of white cement mixed with pigment, laid on 20mm thick bed of ordinary cement mortar 1:3(1 ordinary cement :3 fine sand), joints grouted with white cement slurry containing pigment to match the shade complete in all respect as per specifications and to the entire satisfaction of engineer- in- charge. Ramp

Wrought iron & Mild steel ladders, framed grills, gratings etc. with ends of bars riveted or molded forged framed window guards, barred iron doors stair case iron railing etc. including cost of bolts and nuts, screws, welding rod complete fixing in position Ventilator

Terracing consiting of tiles 22.86x11.43x3.83cm laid over 25 mm mud plaster 7.5 cm mud filling on another layer of 25mm mud plaster including two coats of bitumen laid hot at 1.65 Kg. /Sqm top of R.C.C. slab including grouting with cement sand mortar 1:4 and top surface to be left clean after wire brushing Bathroom

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes (working pressure 4.00 kgf / cm²) conforming to IS : 4985, including jointing with seal ring (i) Single socketed pipes. U-PVC pipes (working pressure 4.00 kgf. / sqcm) Single socketed pipe 110 mm dia.

Bottom khurra on ground 1.2m 0.6m consisting of bricks on edge laid in cement mortar 1:3 over 7.5 cm cement concret 1:8:16 including 12.5mm thick cement plaster 1:3

Sub Head-1 Internal Water Supply System

CONCEALED IN WALL: Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes as per IS 15778 (ISI marked with the prior approval of Engineer-in- Charge), having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing including jointing of pipes & fittings, with one step CPVC solvent cement and testing of pipes complete CPVC SDR 11 Pipe & fitting 16mm o/d

SDR 11 CPVC pipes & fittings 20mm o/d

CPVC SDR 11 Pipe & fitting 25mm o/d

CPVC SDR 11 Pipe & fitting 32 mm o/d

Cutting chase in brick walls in cement or in floor for embedding G.I. or C.I pipes line and making good the same to its original condition.Size 75mm x 75mm

Cutting holes upto 23cm square through B.B. in cement walls or stone masonary wall in cement for pipes, and making good the same & finishing according to existing finish where required. Through wall 11.43 cm thick

Through wall 22.86 cm thick

Providing, fixing and jointing Brass Ball valves screwed with SS/BRASS ball & spindle & Teflon seats, on G.I. Pipe lines including all carriages complete. 20mm i/d Brass Ball valves

25mm i/d Brass Ball valves

Providing, fixing and jointing ISI Marked GunMetal peet valves (Heavy Pattern) as per IS 778 with hand wheels, on G.I. Pipe lines laid in the ground or inside buildings including all carriages complete. 25mm i/d Gun Metal peet valve heavy pattern.

Construction of brick masonry inspection chambers size as given below upto 0.60 metre average depth in 1:5 cement sand mortar, C.C.1:4:8 ( 150mm thick) in foundation, cement concrete 1:2:4 benching 12.50mm thick cement plaster 1:2 with a floating coat of 1mm thick of neat cement, R.C.C. 1:2:4 slabs 100mm thick cement concrete topping 50mm thick with 455mm x 455mm, 455mm x 610mm inside R.C.C. inspection chamber cover and frame (Weight as per I.S.I specifications) painted with 3 coats of black bitumastic paint. 450mm x 600mm inside with 455mm x 610mm cover and frame light duty double seal

Providing and fixing in position singel socket SWR UPVC soil waste or antisyphonage pipes as per IS 13592 of E.D.C manufacture or of any other reputed firm including cutting, jointing, wastage, but excluding cost of jointing. Single Socket Type B 110mm o/d SWR UPVC pipe lines laid complete

Excavation manually in trenches with straight or open cutting in built up street/ lane having wall to wall width of street/ lane upto 3.0 metre, for intramural sullage drains, extramural intercepting drains and outfall drains, storm water channels and other work contingent or incident thereto, to full dimensions and depth as shown on the drawings or as shall be required by Engineerin- charge including dressing to correct sections and dimensions according to templates and levels, dewatering of rain water, diversion of traffic. Providing and fixing and maintenance of caution boards, fencing, night signals, for leads upto 15m and for all lifts and subsequent refilling, watering and dressing upto groung level, including removal of surplus spoil from the site upto 15 metre distance complete in all respects. All classes of soil except rocky

Sub Head-2 Sanitary Installation Providing and fixing in position set of EWC and WHB size 46x36 cm for Handicapped person of approved make (to the approval of the Engineer-in-charge) consisting of matching cistern, one pair mounting brackets, seat cover, one no. hinges rail 76cm and 4 no. grab rails 60cm complete in all respect and to the entire satisfaction of Engineer-in-charge.

Providing and fixing in position gully traps fixed in cement concrete 1:4:8 complete with Grating 150mm x 150mm, cover and frame clear opening 300mm x 300mm and out of side size 330mm x 330mm and chamber including cost of all bricks work in cement morter 1:5 cement concrete 1:2:4 in coping around cover and frame etc. as per standard design minimum depth of water should be 150 mm with a minimum seal 50mm. 100mm internal Diametre S.W.gully trap with H.C.I. grating and cast iron cover weighing approximately 7.26 kg. and frame clear opening 300mm x 300mm and out of side size 330mm x 330mm

Providing and fixing in position C.P. brass, bottle trap 32mm dia with 40 mm seal of approved make (to the approval of Engineer-in-charge) complete in all respect.

Providing and fixing jet spray with 2'-6" long PVC pipe. With C.P. Brass nut

Providing and fixing P.V.C Waste Pipe Collapsiable 32mm complete in all respect..

Providing and fixing Stainless steel health faucet complete in all respect.

Providing and fixing in position C.P brass basin mixer without pop-up waste system with 450 mm long flexible hose of approved make (to the approval of Engineer-in-charge) instead of C.P. brass pillar tap complete in all respect.

Providing and fixing in position C.P. brass soap dish of approved make (to the approval of Engineer-in-charge ) fixed into wall with rawl plugs and C.P brass screws complete in all respect.

Providing & fixing in position PVC flexible tube connection of approved make (to the approval of Engineer-in-charge ) complete in all respect. (e) PVC tube connection of size 15 mm x 300 mm with C.P. Brass nut

Providing & Fixing in postion 15 mm i/d bib cock of approved make (to the approval of Engineer-in-charge )complete in all respect. C.P. brass Bib cock foam flow without flange

Providing & Fixing in postion stop cock / Angle valve of approved make (to the approval of Engineer-in-charge ) complete in all respect. C.P.brass 15mm Concealed stop cock with flange.

C.P.brass 15mm Angle valve without flange

Providing & Fixing in position C.P. Brass flange Dome of approved make (to the approval of Engineer-in-charge ) under various fixtures complete in all respect.

Providing & Fixing in position C.P. Brass extension piece 25mm long to 100mm long of approved make (to the approval of Engineer-in-charge )with various fixtures complete in all respect. i) C.P. Brass extension piece, 25mm long to 50mm long

Providing & placing in position on terrace HDPE water storage tanks of approved make (to the approval of Engineer - in-charge) with cover with suitable locking arrangement and making necessary holes for inlet, outlet and over flo pipes but without fittings and base support for tank. Triple Layer Tanks

Providing and fixing in position C.P. Acrylic shelf with C.P.bracket and guard rails of approved make (to the approval of Engineer-incharge ) fixed in with rawl plugs and C.P brass screws complete in all respect. CP brass Acrylic Shelf size 560mmx130mm

Providing & Fixing in position 5mm thick bevelled edge mirror of superior glass (of approved make) complete with 4mm thick hard board backing fixed in with rawl plugs 50mm, C.P. brass screws and washers and S/S Studs on top complete in all respect (as required by the Engineer-in- Charge) Size 600mmx450mm

Providing & Fixing in position C.P. Brass Hexa Nipple 15mm of approved make (to the approval of Engineer-in-charge ) complete in all respect.

Providing & Fixing in postion liquid soap container of approved make (to the approval of Engineer-in-charge ) complete in all respect. C.P. brass liquid soap container

Providing and fixing in position SS Grating with frame of approved make (to the approval of engineer in charge) complete in all respects.

Providing and fixing in position paper holders of approved make (to the approval of Engineer-in-charge ) fixed in to wall with C.P brass screws complete in all respect. C.P. brass toilet paper holder

Providing and fixing in position automatic brass Ball Cock in tanks. Brass Ball Cock with rod and Plastic Ball 25mm i/d

Providing and fixing in position G.I. Tank Nipple of approved make (to the approval of Engineer-in-charge) in PVC Water storage tanks complete in all respect. G.I. tank nipple 25mm i/d

Construction of Platform for PVC Storage Tank complete as per Specification & as desired by Engineer-in charge

Provision for Sign board

Providing and fixing in position towel rails / ring of approved make (to the approval of Engineer-in-charge ) fixed in with rawl plugs embedded in walls with brass screws complete in all respect. C.P. brass towel Rails size 15mm dia 600mm long

Sub Head-3 Flooring & Tiles Base course of floor consisting of 100mm thick cement concrete 1:8:16 and 100mm sand filling using mechanical mixer for mixing of material

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: i) Ist course of applying cement slurry @ 4.4 Kg/ sqm mixed with water proofing compound conforming to IS : 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg per sqm of area. iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 Kg/sqm).

Providing and fixing 1st quality ceramic glazed wall tiles Matt/Semi Matt/Glosy/Highly Gloss finish/ Highlighter/emboss conforming to IS : 15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of size 600 x 300 mm as approved by Engineer-in- Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:4 (1 cement: 4 fine sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Anti skid Ceramic floor tiles of size 300x300 mm x 10 mm thick of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on flooring skirting and dado in 12.5mm thick cement plaster 1:3 in base and jointed with @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., completewhite cement slurry in joints including corners angles and beading.

Sub Head-4 Internal Sewerage System Providing and fixing in position singel socket SWR UPVC soil waste or antisyphonagepipes as per IS 13592 of E.D.C manufacture or of any other reputed firm including cutting, jointing, wastage, but excluding cost of jointing. Single Socket Type B b) 90 mm o/d SWR UPVC pipe lines laid complete

75mm o/d single socket SWR UPVC pipe lines laid complete

Providing and fixing in position SWR UPVC special for soil waste vent or anti syphonage pipes as per as per IS - 14735 including cutting and wastage etc. cutting holes in walls roofs or floors etc. and making good to its original condition but excluding cost of lead joining.

For 110 mm o/d pipes Elbow 90 Degree (All side socketed)

Vent Cowls

Coupler

P Trap/Floor Trap 110mm x 110mm

Single Tee With Door

For 75 mm o/d pipes Elbow 90 Degree (All side socketed)

Vent Cowls

Coupler

P Trap/Floor Trap 75mm x 75mm

Single Tee With Door

Providing & Fixing in position M.S or heavy flat iron clamps made out of M.S flat iron not less than 5 mm of the approved design for fixing C.I. soil waste, vent or antisyhonage pipes to walls complete in all respects including cutting and making good the walls and floors etc. and painting. M.S. Holder bats clamps for 100mm i/d H.C.I. pipes .

P/F of exhaust fan of 12" of reputed make complete in akll respect.

RECESSED PVC CONDUIT PIPE WIRING SYSTEM WITH MODULAR SWITCHES:Wiring in PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5sq. mm, 1100volts grade to be laid in heavy gauge PVC conduit pipe 20mm/ 25mm dia. (ISI Marked) recessed in wall etc., complete with powder coated/anodized concealed metal boxes (1.6mm thick with Brass lugs) required for suitable number of modules (Modular accessories) for having Step type electronic fan regulators (two module) 100watts, bell push, 6Amp. 2/3 universal socket (shuttered), 16/20Amp. combined/ universal Socket (shuttered), 6/10Amp. Switches, 16/20Amp. switches with indicator etc. and covered with Frame Plate etc., PVC connector (For Fan Box and Call Bell), Steel Hooks, Sheet metal fan box (1.6mm thick shape hexagonal), Circular junction Boxes (Four way PVC 1½" deep for walls and CI 3" deep for ceiling), bonding to earth with PVC insulated copper conductor single core FR cable (ISI marked) 1sq. mm, 1100volts grade (For 6Amp. wall socket & plug control point) and other petty material etc., including the cost of above material, cutting and filling up of chases (with finishing the surface):-

Wiring fan point( with fan box)

Wiring light point

Wiring 6Amp. Plug control comprising wall socket point

Supply and erection of PVC insulated FR single core Unsheathed copper conductor cable (ISI marked) suitable upto 1100 volts grade confirm to IS:694/1990 left bare in pipe or casing of suitable size complete in all respect as desired by the Engineer-in-charge:-

Overall size 1sq.mm (Un-sheathed)

Overall size 2.5sq.mm (Un-sheathed)

PVC, HDPE PIPES & PVC FLEXIBLE PIPES: Supply & erection of PVC Conduit Pipes (ISI marked) as per IS9537:Part-III & HDPE pipes (ISI marked) as per IS:4984:1995 for wiring purposes including bends, junction boxes, Steel hooks, M.S. saddle clamps and other petty materials etc., as per PWD General Specifications:- Heavy Gauge PVC Conduit Pipe 25mm dia. (Flushed)

HEET METAL DOUBLE DOOR DISTRIBUTION BOARD FOR MCB's/ RCBO's/ RCCB's: Supply and erection of sheet metal Double Door Distribution Boards IP 43-IK09 metal door (dust protected) as per IS 8623-1&3, IEC 61439-1&3 suitable for flush mounting with fully insulated copper busbars, shrouded neutral bars, earth bars, cement spill protector, color-coded interconnecting wire set, cable ties, blanking plates and circuit identifications label and of required no. of ways for mounting miniature circuit breakers/ RCBO's/ RCCB's in the distribution board (For SP&N distribution board with provision DP MCB's/ RCCB's/ RCBO's as incomer and SP MCB's as outgoings and for TP&N horizontal distribution board with provision TPN/ FP MCB's/ RCCB's/ RCBO's as incomer and SP MCB's as outgoings) as per PWD General specifications including connections with suitable size of thimbles and bonding to existing earth etc:-

SP&N Double Door Distribution Board 4 way each

MINIATURE CIRCUIT BREAKERS: Supply and erection of Miniature Circuit Breaker MCB's for circuit protection against overload and short circuit current fault suitable for 240/ 415 volts 50cycles AC supply with breaking capacity of 10kA, Curve-C and low watt losses as per IS/IEC 60898-1, energy limitation class-3, true contact indication, label holder facility in the existing MCB distribution board as per PWD General Specifications including connections with suitable size of thimbles/lugs:-

MCB Single Pole 6-32amp. (10kA, Curve-C)

MCB Double Pole 40amp. (10kA, Curve-C)

G.I. EARTHING: Earthing with G.I. wire/ rope in G.I. pipe partly recessed and partly on surface complete with 150cm long 50mm dia. G.I. earth pipe (Cutting threads and 36 Nos. holes, 1cm dia. to make a mesh around the GI Pipe) with G.I. reducing socket including erection of the same, 4.50 metre (14.76 feet) below ground level with 20Kg. charcoal & salt mixture etc., up to 8 metre in length (including boring & refilling). Earthing with 8 S.W.G. (4mm dia.) G.I. wire in 15mm dia G.I. pipe with G.I. reducing socket 50mm x 15mm (upto 8Metre in length)

G.I. EARTHING WIRE/ ROPE (AS ADDITIONAL LENGTH): Fixing additional length of earthing with G.I. wire/ rope in G.I. pipe (Flushed in wall and floor) with sockets, elbows and Steel hooks including the cost of cutting and filling up of chases (with finishing the surface):- Additional length G.I. wire 8 S.W.G. (4mm dia.) in 15mm dia. G.I. pipe (Flushed)

Supply and erection of 12" Heavy Duty Exhaust fan (HDEF) (300mm-900RPM) Single Phase of ISI marked heavy duty motor with die cast Aluminium rotor mounted on two ball bearing including erection, connections and testing etc. complete with flexible wire and petty material reqd. for connections and Aluminium louver shutter complete in all respects as approved and desired by the Engineer-in-charge of site.

Supply and erection of LED batten 20watt LED (including LED driver) with High quality extruded aluminium with efficacy of LED fixture minimum 100 lumens per watt and operating voltage between 140 to 270 volt, input AC frequency 50 Hz ± 3 %. complete along with erection of the same with connections, testing etc. complete in all respects as approved and desired by the Engineer-in-charge at site.The certification and Specifications of the LED Fitting's should be as approved by O/o Advisor (Technical), Govt of Punjab vide Letter no.AT/2021/GL/1410-1422 Dated 06/05/2021. Besides this the lighting fixture manufacturer should have inhouse NABL accredited lab.

Supply & erection of PIR motion sensorfor automatically switching on & off the lighting fixtures complete in all respects as approved and desired by the Engineer-in-charge of site.

Supply and erection of AC Ceiling Fan 900/1200mm 3 Star suitable for 230v single phase with double ball bearing full aluminium body,copper wound,3 number blades white colour.and warranty of 2 years including flexible wire & petty material etc. for connections and testing . complete in all respects as appd. and desired by the Engineer in-charge at site.

Supply & erection of panic switch/emergency call system for disabled in washroom with visual and audio indicator with 1 pull cord,1 siren, 1 LED light blinker 230 volt 50Hz AC operation complete in all respects as approved and desired by the Engineer-in-charge of site.

Calture Cess @1%

Please Enable Macros to View BoQ information