Selection of an Agency for Construction and Redevelopment of Child Welfare Center with Smart Application in Pan City Area under Smart City Mission

Building Structural and Brick Work

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50m and lift up to 1.5m, disposed earth to be levelled and neatly dressed. All kinds of soil

Excavation work in foundation trenches or drains not exceeding 1.5 m in width or 10 sqm on plan including dressing of sides and ramming of bottoms lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50m. Ordinary rock

Supplying and filling in plinth under floors including, watering, ramming consolidating and dressing complete. Moorum/Hard copra

Supplying and filling in plinth under floors including, watering, ramming consolidating and dressing complete. Crusher Stone Dust

Centering and shuttering including strutting, propping etc.and removal of form for : Foundations, footings, bases of columns, etc. For mass concrete.

Centering and shuttering including strutting, propping etc.and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Centering and shuttering including strutting, propping etc.and removal of form for : Stairs, (excluding landings) except spiral-staircases.

Centering and shuttering including strutting, propping etc.and removal of form for : Suspended floors, roofs, landings, balconies and access platform.

Centering and shuttering including strutting, propping etc.and removal of form for : Columns, Pillars, Piers, Abutments, Posts and Struts.

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : Cement concrete grade M-10 (Nominal Mix) with 20 mm maximum size of stone aggregate

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding including cost of binding wire all wastages and overlaps, couplers (overlaps shall be provided as per requirement of IS 13920 for ductile detaling IS 456 RCC Design & SP 34 Reinforcement detailing ) etc. complete . (Note:- 1. Spacer bars (chairs) shall be paid separately as shown in the drawing and as per direction of engineer in charge. 2. No extra payment shall be done for overlaps and/or couplers. 3.Couplers shall be conforming to IS code on “Reinforcement Couplers for Mechanical Splices of Bars for Concrete Reinforcement - Specification”) Thermo-Mechanically Treated bars. (TMT/TMX) FE 500 or more conforming to IS 1786

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : Cement concrete grade M-20 (Nominal Mix) with 20 mm maximum size of stone aggregate.

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up to floor two level excluding cost of centering, shuttering, finishing and reinfor cement Cement concrete grade M-20 (Nominal Mix) with 20 mm maximum size of stone aggregate.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor two level excluding the cost of centering, shuttering, finishing and reinforcement with Cement concrete grade M-20 (Nominal Mix with 20 mm maximum size of stone aggregate).

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete M-15 with aggregate of 20 mm nominal size over P.V.C. sheet 1mx1mx400micron, finished with 12mm cement plaster 1:3 (1cement : 3 coarse sand) and a coat of neat cement rounding the edge sand making and finishing the outlet complete.

Providing and laying in situ seven course water proofing treatment with APP (Atactic poly-propylene) modified Polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40Kg per sqm, 2nd, 4th & 6th courses of bonding material @ 1.20 Kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd and 5th layers of roofing membrane APP modified Polymeric membrane 1.5mm thick of 2.25 Kg/sqm weight consisting of five layers prefabricated with centre core as 20micron HMHDPE film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20micron HMHDPE film. 7th, the top most layer shall be finished with brick tiles of class designation 100 grouted with cement mortar 1:3 (1cement:3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat which shall be paid for separately.

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Wall Finishing (Plaster, Putty, Paint)

Half brick masonry with of class designation 40 in foundation and plinth in.

Extra for providing and placing in position 2 Nos. 6mm dia. M.S. bars at every third course of half brick masonry (with of class designation 40).

Brick work with fly ash lime bricks (FALG Bricks) conforming to IS:12894-2002, in super structure above plinth level up to floor two level in : Cement mortar 1:4 (1 cement : 4 sand)

Providing and fixing of 2mm thick polycarbonate sheet to self-supported roofing system. The sheet shall have tensile strength and elongation as per ASTM D 638, refractive index as per ASTM D 592, light transmission as per ASTM D 1003 and specific gravity as per STM D 792. Polycarbonate sheet shall have foam tap or rubber gasket under and over it and fixed by 1 to 2 mm thick aluminum angle 25X25mm with self-tapping screw to panels. All joints shall be sealed by silicon. Rates include of all material, labour, fittings, screw, foam tap, aluminum angles etc. complete. Deduction shall not be made for cutting area of self-supported roof.

12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)

15mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 fine sand)

6 mm cement plaster of mix : 1:3 (1 cement: 3 fine sand)

Providing and applying flakes textured homogeneous wall finishing system consisting of a two component system of dry flakes (9.5kgs per/pack) made of a special grade of heat treated China clay with rigid homopolymer coated with fade resistant pigments and a 100% acrylic polymer Bonding agent (5kgs/pack) applied thickness of the coating being between 0.8-1.2mm, to be applied in single coat, on a cured, smooth level plaster surface without keying, as per the shades/ combinations approved, as per manufacturers directions for usage, to be applied by approved applicator of manufacturer, as per direction/supervision of the engineers-in-charge inclusive of one coat of primer on the base at all heights etc all complete.

Providing and applying 1.5 mm thick (in two coat) white cement based wall putty of best quality, over plastered surface to prepare the surface even and smooth complete.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Finishing walls with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Two or more coats applied @ 1.25 ltr/10 sqm. over and including one coat of Special primer applied @ 0.75 ltr/10 sqm.

Building Indoor Outdoor Flooring

Providing and fixing Ceramic glazed wall tiles 300x450 mm or more (having thickness 6 to 7 mm) of 1st quality conforming to IS: 15622 of approved make in all Colours& shades, except burgundy, bottle green, black laid on 12mm thick bed of Cement Mortar 1:3 (1 Cement: 3 sand)preprad same day when mortar is still green jointed with grey cement slurry @3.3 kg per sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and laying vitrified floor-tiles Full Body Design Homogenous Body matt/rustic finish in different size with water absorption less than 0.05% and conforming to IS:15622 of approved make in all colours& shades, 1st quality/ premium quality in flooring laid on 20mm thick cement mortar 1:4(1cement :4sand) including grouting the joints with white cement and matching pigments etc. complete. (c) Size 600X600 mm thickness 11-12mm (to be used heavy duty indoor areas of non residencial buildings only such as schools, hostels, libraries hospitals, institutions, offices etc.)

Providing and laying factory made coloured chamfered edge Cement Concrete paver blocks of required strength, thickness and size/shape, made by table vibratory method using PU mould, laid in required colour and pattern over 50mm thick compacted bed of stone dust, compacting and proper embedding/laying of inter locking paver blocks into the bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand including locking edges with M 15 cement concrete in footpath, parks, lawns, drive ways or light traffic parking etc. complete as per manufacturer's specifications and direction of Engineerin- Charge. 60mm thick C.C. paver block of M-35 grade with approved colour, design and pattern.

Providing and fixing 2 mm thick heterogeneous PVC (poly vinyl flooring) EN (European Standard) with wear layer is 0.55mm thick of PVC, total weight is 2300 g/m2 approx. PUR (polyurethane reinforced), residual indentation approx.0.05 mm, castor wheel test qualified, dimensional stability ≤0.10%, static electrical charge <2kv, all vinyl sheets must be linked crosswise with a continuous copper strip and finally connected to earth for grounding electrostatic electrical charges. good resistance to scratch, slip, chemical and fire, doesn’t favour in growth of fungi & bacteria. 100% recyclable (eco-freindly). Low VOC emissions after 28days of installation (lower than ≤10μg/m3). phthalate free technology. directional in design.The floor finish should termite free at the room perimeter passing over a concealed cove forming and continuing up on the wall upto100mm. Recommended to use in area like Patient rooms , Doctor room Lecturer room, Kids area, School, Colleges, Residential and all commercial official scope etc.

Providing and laying Antiskid floor tiles of any sizes, 12 mm thickness with water absorption less than 0.08% and conforming to IS:15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 sand) including grouting the joints with white cement with matching pigments etc., complete.

Building Door Window & Accessories

Providing and fixing expandable fasteners of specified size with necessary plastic sleeves and galvanised M.S. screws including drilling holes in masonry work /CC/ R.C.C. and making good etc. complete. 40 mm long

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position : Other then teak wood

12 mm thick one side Pre-laminated particle board (decorative lamination on one side and other sides balancing lamination) grade - 1 medium density flat pressed, three layer particle board FPT - I or graded wood particle board FPT-1 conforming to IS : 3087 bonded with BWP type synthetic resin adhesive as per IS : 848 and pre-laminated conforming to IS : 12823 Grade -1, Type II marked:

Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete : 100x60x2.50 mm

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 150x10 mm

Providing and fixing ISI marked 85x42mm oxidised M.S. pull bolt lock conforming to IS : 7534 with necessary screws bolts, nut and washers etc. complete.

Providing and fixing ISI marked oxidised M.S. door latches conforming to IS:5930 with screws etc. complete : 250x20x6 mm

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete : 100 mm

Providing and fixing oxidised Mild Steel hasp and staple (safety type) conforming to IS : 363 with necessary screws etc. complete : 115mm

Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. Twin rubber stopper

Providing and fixing IS : 3564 marked aluminium extruded section body tubular type universal hydraulic door closer with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing factory made 100% solid wood plastic composite (WPC) door frames made from wood plastic composite ( single extruded process) material with density 0.78 kg/cum and manufactured by a ISO 9001-2000 certified company .Water absorption not more than 0.01% cum. WPC door frame-single rebate ( 90 mm x 45 mm )

Providing and fixing factory made laminated 100% solid PVC flush door shutter ( 28 mm thickness ) made from rigid PVC foam sheet (Single Extruded) with density 600 kg/cum and laminated on both sides by laminated sheet/ PVC foil lamination at the manufacturing process itself. 28 mm thick pre laminated solid PVC flush door shutter

Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with L-Type section made of 1.60 mm thick M.S. Sheet, joints mitred and welded and grinded finish profiles required size with 15x3mm lugs 10cm long embedded in cement concrete M-10 (Nominal Mix with 20mm maximum size of stone aggregate) blocks 15x10x10cm or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as required including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primers.

Building Water Supply Work

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 50 mm nominal outer dia Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 40 mm nominal outer dia Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc. 32 mm nominal outer dia Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc. 25 mm nominal outer dia Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 20 mm nominal outer dia Pipes.

Providing and fixing G.I. pipes medium class complete with G.I. fittings as per IS : 1239 (Part-2) including trenching and refilling etc. External work 50 mm dia. nominal bore

Providing and fixing G.I. pipes medium class complete with G.I. fittings as per IS : 1239 (Part-2) including trenching and refilling etc. External work 32 mm dia. nominal bore

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal bore

Providing and fixing brass stop cock of approved quality : 15 mm nominal bore 0.40kg

Providing and fixing C.P. brass grating of approved quality and make conforming to IS: specification. 100 mm dia.

Providing and fixing C.P. brass soap container 109 mm wide,125 high and 112 mm distance from wall of standard shape with bracket of the same material with all fittings etc. of approved quality and make like Jaguor or equivalent conforming to IS:specification.

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 100 mm diameter

Providing and placing on at all floor levels high design HDPE (polyethylene) water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mm nominal bore

Providing and fixing gun metal non- return valve of approved quality (screwed end) : Horizontal 32 mm nominal bore

Providing and fixing G.I. Union (ISI mark) in G.I. pipe line including cutting and threading the pipe and making long screws etc complete (new work) : 32 mm nominal bore

Providing and fixing G.I. Union (ISI mark) in G.I. pipe line including cutting and threading the pipe and making long screws etc complete (new work) : 40 mm nominal bore

Making chases up to 7.5 x 7.5 cm in wallls including making good and finishing with matching surface after housing G.I.pipe etc.

Building Drainage Work

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 75 mm outlet Sand cast iron S&S as per IS - 3989

Bottle trap 38mm single piece moulded with height of 270mm, effective length of tail pipe 260mm from the centre of the waste coupling 77mm breadth with 25mm minimum water seal, weighing not less than 263gms.

Providing and fixing square-mouth S.W. gully trap grade 'A'‟ complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design : With Modular Bricks class designation 40. 150 x 100 mm size P type.

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 300 mm dia. R.C.C. pipe

Constructing brick masonry moudlar brick class designation 40 manhole in cement mortar 1:4 (1 cement : 4 sand ) R.C.C. top slab with Cement concrete grade M-20 (Nominal Mix with 20mm maximum size of stone aggregate), 20 cm thick foundation concrete grade M-7.5 (Nominal Mix with 40mm maximum size of stone aggregate) inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 sand) finished with floating coat of neat cement and making channels in cement concrete grade M-15 (Nominal Mix with 20mm maximum size of stone aggregate) as per standard design. The sizes of manhole and manhole covers as detailed below. Manhole inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete grade M-15 (Nominal Mix with 20mm maximum size of stone aggregate) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 sand) finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : For pipes 250 to 300 mm diameter

Constructing brick masonry road gully chamber 50x45x60 cm with bricks of class designation 40 in cement mortar 1:4 (1 cement : 4 sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame (minimum weight of grating 75 kg) complete as per standard design : With Modular bricks

Providing and laying below ground unplasticised PVC pipe to with stand working pressure of 4 kg/cm2 soild waste pipes confirming to IS:13592 and IS:4985 including jointing with seal ring confirming to IS :5282 leaving 10mm gap for thermal expansion all necessary fittings etc. complete. 110 mm diameter OD

Building Sanitary Work

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete including painting of fittings and brackets, cutting and making good the walls and floors wherever required :Size 270mmx415mmx310mm(for children) W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink without drain board 610x510 mm bowl depth 200 mm.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 32mm dia

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 453x357mm

Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10cm of cement concrete grade M-15 (Nominal Mix with 20mm maximum size of stone aggregate) including cost of cutting holes and making good the walls etc. : For 100mm dia pipe

Providing and fixing plain bend of required degree. 100 mm Sand cast iron S&S as per IS – 1729

Providing and fixing double equal junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete : 100x100x100x100mm Sand cast iron S&S as per IS – 1729

Providing and fixing double equal plain junction of required degree. 100x100x100x100mm Sand cast iron S&S as per IS – 1729

Providing and fixing single unequal plain junction of required degree : 100x100x75mm Sand cast iron S&S as per IS – 1729

Cutting chases in brick masonry walls for following diameter sand cast iron/ centrifugally cast (spun) iron pipes and making good the same with cement concrete grade M-10 (Nominal Mix with 20mm maximum size of stone aggregate) including necessary plaster and pointing in cement mortar 1:4 (1 cement : 4 coarse sand) : 100mm dia

Providing and fixing sand cast iron S&S off sets as per IS: 1729 75 mm off sets With 100 mm dia. Pipe

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. Waste coupling 31mm of 79mm length and 62mm breadth weighing not less than 45gms.

Supply, installation, testing and commissioning of evacuated tube collectors solar water heating system having water circulation natural thermo syphon suitable for inlet water with chloride hardness up to 600 ppm & TDS up to 1000 ppm comprising of evacuated tube collectors with double walled vacuum tube made from hard borosilicate glass able to resist impact from hail stone up to 30 mm in diameter, of length 1800mm having ID/OD 48/58mm, thickness 1.6mm.heavy duty HR black CGO-4 steel of 2 mm thick horizontal cylindrical hot water tank with dished end capsule shape including access doors having PUF/rock wool insulation density 42 Kg/cu. mt., 50mm thick having nonstick lining inside the tank and UV stabilized polyester precoated G.I. outer cover. Stand assembly for tank having polyester powder coated G.I. folded angles and electrical back up 2 KW. Heat loss < 0.70 W/ (m 2˚C ), The system should be as per latest specifications of IREDA/BIS/MNRE norms and valid test reports issued by authorized test centers confirming to MNRE guidelines for following capacities :- Rated capacity 500 LPD, storage tank 500 Ltr

Landscaping & Greenery Work Children Play Equipment

Swing two seater

STP FRP Slider

See-Saw

36mm Rubber Concrete for EPDM Flooring (Minimum Base Rubber 30MM and EPDM 6MM)

Supplying and stacking of good earth at site including royalty and carriage up to 1 km (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking sludge at site including royalty and carriage up to 1 km (sludge measured in stacks will be reduced by 8% for payment).

Supplying and stacking at site dump manure from approved source, including carriage up to 1 km (manure measured in stacks will be reduced by 8% for payment) Screened through sieve of I.S. designation 16mm

Mixing earth and sludge or manure in proportion specified or directed.

Filling mixture of earth and sludge or manure in the desired proportion in trenches, flooding with water and leveling (cost of supplying earth and sludge or manure and mixing excluded).

Grassing with „Doob‟ grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn free from weeds and fit for mowing including supplying good earth if needed (the good earth shall be paid for separately). In rows 7.5 cm apart in either direction.

Preparation of beds for hedging and shrubbery by excavating 60cm deep and trenching the excavated base to a further depth of 30cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1(8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50m lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately).

Edging with bricks laid dry length wise including excavation, refilling, consolidating with hand packing and spreading neatly surplus earth within a lead of 50 m 40 class designation.

Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly, as per direction of officer-in-charge.

Duranta Golden plant, having ht.15 to 20 cm bushty shape plant with fresh and healthy leaves in 20 cm size of Earthen Pot / Plastic Pot.

Alternanthera species plant of height 15 cm to 20 cm, full of branches and foliage in 15 cm size of Earthen Pot / Plastic Pot.

Setcreasea purpurea full of variegated leaves in 20 cm size of Earthen Pot/Plastic Pot.

Dianella variegated plant, with 3 to 4 variegated leaves in 20 cm size of Earthen Pot / Plastic Pot.

Foxtail palm of plants ht. 240-270 cm bottom girth 35-40 cm well developed in big size HDPE bags

Providing and displaying of Areca palm plant, having ht. 1.50 m to 1.80 m with 6 to 8 suckers, well developed, fresh and healthy with lush green foliage in 25 cm size of Earthen pot / Plastic pot & as per direction of the officer-in-charge.

Cyprus Golden 30 to 45 cm ht. plant well developed good Golden colour foliage, Conial Shape in 25 cm Earthen Pots

Bottle palm of plants ht. 210-240 cm bottom girth 30-35 cm well devedoped in big HDPE bags.

Providing Plant Marigold jaffri dwarf in different colour well developed with fresh & healthy foliage with 12 to 15 flowers in full bloom specimen plant 23 to 30 cm ht. in 20 cm Earthen Pot/Plastic Pot.

Providing of Draceana Song of India Green plant (three in one), having ht. 30 cm, well developed, fresh & healthy, lush green foliage from bottom to top in 20 cm size of Earthen pot / Plastic pot.

Internal Electrical Work

WIRING IN CONCEALED RIGID PVC CONDUIT (HEAVY DUTY) SYSTEM WITH MODULER ACCESSORIES Point wiring including metallic switch box, sheet, switche, socket, lamp holders/ceiling roses etc with 1.5 Sq. mm. PVC insulated cable FR with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) ISI Marked of suitable size and 1.5 Sq. mm. PVC insulated copper earth continuity conductor of green colour inside conduit including painting etc. as required as per specification for :- Light Point/Fan Points. a) Short point

WIRING IN CONCEALED RIGID PVC CONDUIT (HEAVY DUTY) SYSTEM WITH MODULER ACCESSORIES Point wiring including metallic switch box, sheet, switche, socket, lamp holders/ceiling roses etc with 1.5 Sq. mm. PVC insulated cable FR with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) ISI Marked of suitable size and 1.5 Sq. mm. PVC insulated copper earth continuity conductor of green colour inside conduit including painting etc. as required as per specification for :- Light Point/Fan Points. b) Medium point

WIRING IN CONCEALED RIGID PVC CONDUIT (HEAVY DUTY) SYSTEM WITH MODULER ACCESSORIES Point wiring including metallic switch box, sheet, switche, socket, lamp holders/ceiling roses etc with 1.5 Sq. mm. PVC insulated cable FR with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) ISI Marked of suitable size and 1.5 Sq. mm. PVC insulated copper earth continuity conductor of green colour inside conduit including painting etc. as required as per specification for :- Light Point/Fan Points. c) Long point

WIRING IN CONCEALED RIGID PVC CONDUIT (HEAVY DUTY) SYSTEM WITH MODULER ACCESSORIES Point wiring including metallic switch box, sheet, switche, socket, lamp holders/ceiling roses etc with 1.5 Sq. mm. PVC insulated cable FR with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) ISI Marked of suitable size and 1.5 Sq. mm. PVC insulated copper earth continuity conductor of green colour inside conduit including painting etc. as required as per specification for :- 3 Pin 6 Amp socket outlet on Separate Board a) Short point

WIRING IN CONCEALED RIGID PVC CONDUIT (HEAVY DUTY) SYSTEM WITH MODULER ACCESSORIES Point wiring including metallic switch box, sheet, switche, socket, lamp holders/ceiling roses etc with 1.5 Sq. mm. PVC insulated cable FR with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) ISI Marked of suitable size and 1.5 Sq. mm. PVC insulated copper earth continuity conductor of green colour inside conduit including painting etc. as required as per specification for :- 3 Pin 6 Amp socket outlet on Separate Board b) Medium point

WIRING IN CONCEALED RIGID PVC CONDUIT (HEAVY DUTY) SYSTEM WITH MODULER ACCESSORIES Point wiring including metallic switch box, sheet, switche, socket, lamp holders/ceiling roses etc with 1.5 Sq. mm. PVC insulated cable FR with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) ISI Marked of suitable size and 1.5 Sq. mm. PVC insulated copper earth continuity conductor of green colour inside conduit including painting etc. as required as per specification for :- 3 Pin 6 Amp socket outlet on Separate Board c) Long point

Circuit Wiring Wiring for circuit wiring with PVC insulated cable FR with copper multi strand conductor ISI marked in Surface rigid P.V.C. conduit (MMS) of ISI marked suitable size including painting etc. as required as per specification. a) 2x2.5 Sq.mm.

Circuit Wiring Wiring for circuit wiring with PVC insulated cable FR with copper multi strand conductor ISI marked in Surface rigid P.V.C. conduit (MMS) of ISI marked suitable size including painting etc. as required as per specification. b) 4x2.5 Sq.mm.

Circuit Wiring Wiring for circuit wiring with PVC insulated cable FR with copper multi strand conductor ISI marked in Surface rigid P.V.C. conduit (MMS) of ISI marked suitable size including painting etc. as required as per specification. c) 6x2.5 Sq.mm.

MODULAR SWITCH BOXES Supplying and fixing of approved make modular type metal box with modular frame/ base plate and cover plate including fixing in concealed / surface excluding switch,socket etc. as required for:- 1 Or 2 Module

MODULAR SWITCH BOXES Supplying and fixing of approved make modular type metal box with modular frame/ base plate and cover plate including fixing in concealed / surface excluding switch,socket etc. as required for:- 4 Module

MODULAR SWITCH BOXES Supplying and fixing of approved make modular type metal box with modular frame/ base plate and cover plate including fixing in concealed / surface excluding switch,socket etc. as required for:- 8 Module

Supplying of ISI Marked and accepted standard of Miniature Circuit Breaker (MCB) of 'C' series suitable for 240/415 Volts, 50 Cycle , 10 kA Value AC supply confirming to IS : 8828 : 1996, IEC : 60898 :2002 but without enclosures :- SINGLE POLE (SP) 6 Amp to 32 Amp Rating

Supplying of ISI Marked and accepted standard of Miniature Circuit Breaker (MCB) of 'C' series suitable for 240/415 Volts, 50 Cycle , 10 kA Value AC supply confirming to IS : 8828 : 1996, IEC : 60898 :2002 but without enclosures :- FOR TRIPLE POLE (TP) For 40 Amps. Rating only.

Supplying of ISI Marked and approved make of Moulded Case Circuit Breaker (MCCB) suitable for 3 phase,3 pole, 50 Hz, 415 Volts, AC supply with respective interrupting capacity (KA) at 415 Volts cited against their range standard conforming to IS - 8828 MCCB with Breaking Capacity 25 KA at 415 V Current Rating -25 to100 Amps & 70% -100% adjustable

Supplying of approved make, powder coated Vertical TPN MCB DB Metal Double Door with MCCB 100A TP 10kA as incomer and space for SP/TP MCBs as outgoing (without MCBs) inclusive of busbar &connections etc without MCB: 8 way with MCCB

Fixing of MCB /MCCB/ Isolator Fixing of MCB / Isolator SP/DP in sheet steel enclosure as required as per accepted practice, including mounting on busbar and cable connection etc. complete (Labour only )

Supplying and fixing as per specification Call bell / buzzer of approved make with necessary materials complete. Ding Dong bell

Suppling and fixing of approved make step type Modular electronic, Fan regulator single/double module including connection etc. as required on existing board upto 120 watt

Supplying, erection and testing of approved make electric Ceiling fan of double ball bearing complete with standard down rod, canopy, hanging shackle, Aluminium blades, without regulator, A.C. 230-250 volts including connections with all necessary material complete as required confirming to IS :374/1979 with upto date ammendments. Ceiling Fan (Energy Saver 50 W)-1200 mm Sweep

Supplying, erection and testing of approved make Wall Mounting fan complete with Wall Bracket ,canopy, blades, speed Regulator etc .A.C 230- 250 volts with connections and including raw bolt/Anchor hole fastener etc.complete finished and as required. 400 sweep

Supplying, erecting and testing of approved make Exhaust Fan heavy duty with mounting frame, blades AC 230-250 complete connection and including, frame bolt/ Anchor hole fastners etc. complete finished and as required. 380mm sweep 900 RPM

Supply and fixing Led tube rod comprising of LED tube with non-integral/integral driver, upto 6500K color temp having 40000 burning hrs life with minimum @ L 70, system lumen output should be minimum with system efficacy> 100 lm/Watt. LED driver PF> 0.95 & THD < 20%. The colour rendering index of LED light should be more than 70. Submission LM 79-08/IS16106 (2012), IEC60598, IEC61347i/c connection wire, testing etc. to complete the job. Tube light LED 1 X 20/22Watt, Integral i/c batten aluminium body, PC diffuser.

Supplying,Fixing and Testing of Compact Flourescent Lamp (CFL) with inbuilt electronic ballast ISI marked of approved make as required as per specification 15 Watt

Supplying and drawing PVC insulated copper cable ( Earth Continuity Conductor ) of Green colour FR with copper multi strand conductor ISI marked in existing conduit along with other wires as required as per specification : 6 Sq mm.

Supplying and drawing PVC insulated copper cable ( Earth Continuity Conductor ) of Green colour FR with copper multi strand conductor ISI marked in existing conduit along with other wires as required as per specification : 10 Sq mm.

Supplying & Installation of approved Make required capacity single phase, 50 Hz,220V, Centrifugal Mono-block pump self priming, with Starter , connections, base channel foundation etc. as required as per specifications but excluding Pipe and connection cable. 1 H.P. Head Mt 6-30, Discharge LPH 2400-900

Supply and fixing of recessed mounting type Led light fixture, LED of 1 to 3 Watt each assembled on single MCPCB, having color temp upto 6500K & having 50000 burning hrs life with minimum @ L 70, system lumen output should be minimum with efficacy>100 lm/Watt. LED driver PF> 0.95, THD < 20% & surge protection 4KV. The colour rendering index of LED light should be more than 70. Housing made of CRCA powder coated frame with glare free diffused polycarbonate cover. Submission LM 79-08/IS16106 (2012), IEC60598, IEC61347i/c connection wire, testing etc. to complete the job. LED luminiare 2' X 2', 36Watt, color temp 3000- 6500k as required.

Other Miscellaneous Work

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc. including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete i/e fixing the railing with necessary accessories and stainless steel dash fastners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge. (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fastners etc.)

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing and staircase railing including applying a priming coat of approved steel primer. M.S. tube.

Providing and fixing concertina coil fencing with required dia 610 mm(having 15 nos. round per 6 meter length) up to 3m height of wall with existing angle iron 'Y' shaped placed 2.4 m or 3.00 m apart and with 9 horizontal R.B.T. stud tied with G.I. staples and G.I. clips to retain horizontal including necessary bolts or G.I. barbed wire tied to angle iron all complete as per direction of Engineer-in- charge with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 3.478gm/ meter (cost of M.S. angle, C.C. blocks shall be paid separately)

IT Component

RFID Card

RFID Card Biometric Access Control System

Supply, Installation testing and commissioning of the IP dome camera shall be equipped with a 1/2.8 2 MP progressive scan CMOS imager to capture full HD 1080p (25/30 fps) images, a 3.6 mm fixed lens, and a waterproof (IP66) enclosure. As a true day/night solution, the camera shall use smart IR technology and provide up to 98 ft (30 m) of IR illumination. The camera shall accept PoE 802.3af) or 12 V DC power input. min. illumination:-0.1 lux @F1.2, AGC ON, 0 lux with IR video compression :- H.264, noise reduction: 3DNR,backlight compensation :- BLC/HLC/DWDR, encode mode:- CBR/VBR (freely adjustable in CBR, 5 levels in VBR). UL listed

Supply, installation testing and commissioning of 4CH network video recorder with real-time recording: up to 4 MP resolution live view, preview and playback/up to 4 channels at 1080p,withinbuilt PoE, up to 1TB supports complete with UL certification

Hard disk Providing &fixing of 2 TB hard disk

All in one i5 (10th Generation or above)Computer with 24inch Monitor, 8 GB Ram and 1TB HDD / 512GB SSD Drive and all other Accessories i.e. mouse, key board with softwares i.e. Microsoft Office, OS etc.

55 INCH Smart Led TV

Cofe Device

SIM with 5 GB per Day plan for 2 years

Mobile APP/Website

Passive Component

IT Technical 1 Persons for 2-years (24 Months)

M/s Landmark Corporation Pvt. Ltd.

RAJENDRA SINGH LODHI