Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹19.1 CrAccepted-AOC THIRD FLOOR AMIT CRYSTAL SENAPATI BAPAT ROAD PUNE 411 016 | PUNE | PUNE | MAHARASHTRA | 411016 | ₹19.1 Cr | L1 | Accepted-AOC L1 |
| 2 | L2₹19.7 CrRejected-AOC OFFICE NO 515 PLOT NO 194 NMS ICON SECTOR 19 ULWE NAVI MUMBAI MAHARASHTRA 410206 | NAVI MUMBAI | THANE | MAHARASHTRA | 410206 | ₹19.7 Cr | L2 | Rejected-AOC L2 |
| 3 | L3₹20.2 CrRejected-AOC 286 2 PARAG STATION ROAD BUDHWAR PETH KARAD SATARA | PUNE | MAHARASHTRA | 412206 | ₹20.2 Cr | L3 | Rejected-AOC L3 |
Tender Value
₹18.3 Cr
EMD Value
₹9.2 L
Closing Date
21 Sept 2024, 6:00 pmClosed
Executive Engineer Public Work(East)Division Pune
Executive Engineer Public Work(East)Division Pune
CONSTRUCTION OF SUB DISTRICT HEADQUARTERS FOR POLICE DEPT. AT BARHANPUR FOR SP (PUNE RURAL) TAL. BARAMATI, DIST. PUNE (BALANCE WORK OF REVISED A.A)
2024_PWDRP_1085500_1
E Tender Notice No.72 for 2024-2025
Open Tender
Civil Works - Buildings
365 days
BARAMATI
Please refer Tender documents.
3 documents required · 3 mandatory
₹3,540
₹9.2 L
Chief Engineer, P. W. Region Office, Pune
6 Nov 2024
14 Sept 2024
23 Sept 2024
14 Sept 2024
21 Sept 2024
14 Sept 2024
14 Sept 2024 - 18 Sept 2024
18 Sept 2024
Amount
Ground floor Providing fly ash brick masonry with conventional / I.S. type fly ash bricks in C.M. 1:6 in foundation and plinth including bailing out water manually striking joints, racking out joints watering and scaffolding etc. complete.
Ground Floor Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, Steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to beprovided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)
Ground floor Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap / granite /quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip oundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, Steel centering, formwork ,cover blocks, laying/pumping, compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based PLC with SCADA nabledconcrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)
A) Ground Floor Providing and applying gypsum plaster ( with Gypsum material of Gypsum India / Mega Sign or equivalent make ) with finishing with gypsum material in 10 to 13 millimeter thickness to previously plastered surface / or on newly brick surface ( Excluding rough cast plaster ) in all position including preparing and Finishing the surface scaffolding etc.complete.
B) First Floor Providing and applying gypsum plaster ( with Gypsum material of Gypsum India / Mega Sign or equivalent make ) with finishing with gypsum material in 10 to 13 millimeter thickness to previously plastered surface / or on newly brick surface ( Excluding rough cast plaster ) in all position including preparing and Finishing the surface scaffolding etc.complete..
C) Second Floor Providing and applying gypsum plaster ( with Gypsum material of Gypsum India / Mega Sign or equivalent make ) with finishing with gypsum material in 10 to 13 millimeter thickness to previously plastered surface / or on newly brick surface ( Excluding rough cast plaster ) in all position including preparing and Finishing the surface scaffolding etc.complete.
A) Ground Floor Providing and applying plaster with plaster of paris in 6mm thickness to previously plaster surface in all position including preparing the surface scaffolding etc. complete.
B) First Floor Providing and applying plaster with plaster of paris in 6mm thickness to previously plaster surface in all position including preparing the surface scaffolding etc. complete.
C) Second Floor Providing and applying plaster with plaster of paris in 6mm thickness to previously plaster surface in all position including preparing the surface scaffolding etc. complete.
A) Ground Floor Providing and laying in position flooring of telephone black / Amba White / Cat bary brown / Ruby red / Ocean Brown granite stone of approved shade and size 18 mm to 20 mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete.
B) First Floor Providing and laying in position flooring of telephone black / Amba White / Cat bary brown / Ruby red / Ocean Brown granite stone of approved shade and size 18 mm to 20 mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete.
A) Ground Floor Providing and fixing machine cut machine polished 18 mm to 20 mm thick telephone black / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone for treads and risers ofsteps and staircases of approved colour and shade with full moulding and three grooved linefor the treads on bed of 1:4 Cement mortar including float filling joints with neat cementslurry curing polishing and cleaning etc. complete.
A) Ground Floor Providing and laying vitrified mirror / glossy finish tiles having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete
B) First Floor Providing and laying vitrified mirror / glossy finish tiles having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete
C) Second Floor Providing and laying vitrified mirror / glossy finish tiles having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete
A) Ground Floor Providing and laying vitrified matt fininsh tiles having size 590 mm to 605 mm x to 605 mmof 8 to 10 mm thickness and confirming IS. 15622-2006 (Group Bla) of approved make,shade and pattern for flooring in required position laid on a bed of 1:4 cement morarincluding neat cement float, filling joints, curing and cleaning etc. complete.
B) First Floor Providing and laying vitrified matt fininsh tiles having size 590 mm to 605 mm x to 605 mmof 8 to 10 mm thickness and confirming IS. 15622-2006 (Group Bla) of approved make,shade and pattern for flooring in required position laid on a bed of 1:4 cement morarincluding neat cement float, filling joints, curing and cleaning etc. complete.
C) Second Floor Providing and laying vitrified matt fininsh tiles having size 590 mm to 605 mm x to 605 mmof 8 to 10 mm thickness and confirming IS. 15622-2006 (Group Bla) of approved make,shade and pattern for flooring in required position laid on a bed of 1:4 cement morarincluding neat cement float, filling joints, curing and cleaning etc. complete.
A) Ground Floor Providing and laying Vitrified MATT finish having decorative type of size 1000 millimeter x 1000 millimeter of 8 to 10 millimeter thickness (on a existing flooring) with bonding chemical and confirming to IS 15622-2006 (Group Bla) of approved make shade and pattern for flooring in required position laid on a bed of bonding chemical filling joints curing and cleaning etc .complete.
B) First Floor Providing and laying Vitrified MATT finish having decorative type of size 1000 millimeter x 1000 millimeter of 8 to 10 millimeter thickness (on a existing flooring) with bonding chemical and confirming to IS 15622-2006 (Group Bla) of approved make shade and pattern for flooring in required position laid on a bed of bonding chemical filling joints curing and cleaning etc .complete.
C) Second Floor Providing and laying Vitrified MATT finish having decorative type of size 1000 millimeter x 1000 millimeter of 8 to 10 millimeter thickness (on a existing flooring) with bonding chemical and confirming to IS 15622-2006 (Group Bla) of approved make shade and pattern for flooring in required position laid on a bed of bonding chemical filling joints curing and cleaning etc .complete.
A) Ground Floor Providing and constructing granite kitchen platform with fixing of stainless steel sink 600mm x 450 mm size as per detailed drawing including vertical both side polished kadappahstone 25 to 30 mm thick supports with kadappah top 35 to 40 mm thick and polished granite16 to 20 mm top with side strips of granite at front and both sides of platform raised with twovertical granite supports 15 cm height and top granite of 75 x 40 cm including cutting,opening for sink of required size in kadappah as well as granite etc. complete. (Platform topsize 5.00 m x 0.60 m and height is 0.75 m)
B) First Floor Providing and constructing granite kitchen platform with fixing of stainless steel sink 600mm x 450 mm size as per detailed drawing including vertical both side polished kadappahstone 25 to 30 mm thick supports with kadappah top 35 to 40 mm thick and polished granite16 to 20 mm top with side strips of granite at front and both sides of platform raised with twovertical granite supports 15 cm height and top granite of 75 x 40 cm including cutting,opening for sink of required size in kadappah as well as granite etc. complete. (Platform topsize 5.00 m x 0.60 m and height is 0.75 m)
C) Second Floor Providing and constructing granite kitchen platform with fixing of stainless steel sink 600mm x 450 mm size as per detailed drawing including vertical both side polished kadappahstone 25 to 30 mm thick supports with kadappah top 35 to 40 mm thick and polished granite16 to 20 mm top with side strips of granite at front and both sides of platform raised with twovertical granite supports 15 cm height and top granite of 75 x 40 cm including cutting,opening for sink of required size in kadappah as well as granite etc. complete. (Platform topsize 5.00 m x 0.60 m and height is 0.75 m)
C) Second Floor Providing and applying priming coat on concrete/ masonary/ Asbestos Cement plastered surfaces including scaffolding if necessary, preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and sand papering as required etc. complete.
A) Ground Floor Providing and applying two coats Apex Ultima Puranature Anti-Pollution Or equivalent approved brand, paint should decomposes organic substances and inorganic gases(NOx, VOC’s, CO, SOx, formaldehydes, etc.) in presence of natural or artificial light. It contains Graphene and nanoparticles of titanium oxide. and Absorbs CO2 (4.8 Kilogram/15 l). plaster crack should be filled by Acrylic base Crack seal/Textured Crack filler, Paint has to applied on one coat of Apex Ultima Puranature Anti-Pollution Primer or Equivalent. Warranty Should be given by the Manufaturer The work should be done by the Manufacturer Recommended applicator and he should be able to furnish stage wise onsite technical reports from the concerned company technologist.
B) First Floor Providing and applying two coats Apex Ultima Puranature Anti-Pollution Or equivalent approved brand, paint should decomposes organic substances and inorganic gases(NOx, VOC’s, CO, SOx, formaldehydes, etc.) in presence of natural or artificial light. It contains Graphene and nanoparticles of titanium oxide. and Absorbs CO2 (4.8 Kilogram/15 l). plaster crack should be filled by Acrylic base Crack seal/Textured Crack filler, Paint has to applied on one coat of Apex Ultima Puranature Anti-Pollution Primer or Equivalent. Warranty Should be given by the Manufaturer The work should be done by the Manufacturer Recommended applicator and he should be able to furnish stage wise onsite technical reports from the concerned company technologist.
C) Second Floor Providing and applying two coats Apex Ultima Puranature Anti-Pollution Or equivalent approved brand, paint should decomposes organic substances and inorganic gases(NOx, VOC’s, CO, SOx, formaldehydes, etc.) in presence of natural or artificial light. It contains Graphene and nanoparticles of titanium oxide. and Absorbs CO2 (4.8 Kilogram/15 l). plaster crack should be filled by Acrylic base Crack seal/Textured Crack filler, Paint has to applied on one coat of Apex Ultima Puranature Anti-Pollution Primer or Equivalent. Warranty Should be given by the Manufaturer The work should be done by the Manufacturer Recommended applicator and he should be able to furnish stage wise onsite technical reports from the concerned company technologist.
A) Ground Floor Providing and applying washable oil-bound distemper of approved colour and shade to oldand new surfaces in two coats including scaffolding, preparing the surfaces. (excluding theprimer coat.) etc. complete.
B) First Floor Providing and applying washable oil-bound distemper of approved colour and shade to oldand new surfaces in two coats including scaffolding, preparing the surfaces. (excluding theprimer coat.) etc. complete.
C) Second Floor Providing and applying washable oil-bound distemper of approved colour and shade to oldand new surfaces in two coats including scaffolding, preparing the surfaces. (excluding theprimer coat.) etc. complete.
A) Ground Floor Providing and Fixing mat finish stainless steel (of 302 grade ) railing with top pipe of 50 mm dia. and vertical pipe of 38 mm dia at 0.60 m c/c or as required and horizontal pipes of 25 mm dia in three rows, all pipes of 2 mm thick including buffing,fabricating fixtures and fastening including pipe base of appropriate diameter and ball base of 75 mm dia above newel post of 75 mm diameter etc. complete (Prior approval of sample and brand by Ex.Engineer is necessary before use)
B) First Floor Providing and Fixing mat finish stainless steel (of 302 grade ) railing with top pipe of 50 mm dia. and vertical pipe of 38 mm dia at 0.60 m c/c or as required and horizontal pipes of 25 mm dia in three rows, all pipes of 2 mm thick including buffing,fabricating fixtures and fastening including pipe base of appropriate diameter and ball base of 75 mm dia above newel post of 75 mm diameter etc. complete (Prior approval of sample and brand by Ex.Engineer is necessary before use)
C) Second Floor Providing and Fixing mat finish stainless steel (of 302 grade ) railing with top pipe of 50 mm dia. and vertical pipe of 38 mm dia at 0.60 m c/c or as required and horizontal pipes of 25 mm dia in three rows, all pipes of 2 mm thick including buffing,fabricating fixtures and fastening including pipe base of appropriate diameter and ball base of 75 mm dia above newel post of 75 mm diameter etc. complete (Prior approval of sample and brand by Ex.Engineer is necessary before use)
A) Ground Floor Providing and fixing fiber glass reinforced polyster door shutter 35 mm thick as per IS 14856 (2000) (Reaffirmed 2006) without ventilator including chromium plated fixtures and fastening with chromium plated handles on both sides, etccomplete.
B) First Floor Providing and fixing fiber glass reinforced polyster door shutter 35 mm thick as per IS 14856 (2000) (Reaffirmed 2006) without ventilator including chromium plated fixtures and fastening with chromium plated handles on both sides, etccomplete.
C) Second Floor Providing and fixing fiber glass reinforced polyster door shutter 35 mm thick as per IS 14856 (2000) (Reaffirmed 2006) without ventilator including chromium plated fixtures and fastening with chromium plated handles on both sides, etccomplete.
A) Ground Floor Providing and applying top coat exterior paint to terrace of approved make, shade and quality and one coat of primer before applying textured paint including scaffolding if necessary preparing surface by throughly cleaning of oil, grease, dirt and other material and fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) preparing as required, etc. complete.
B) First Floor Providing and applying top coat exterior paint to terrace of approved make, shade and quality and one coat of primer before applying textured paint including scaffolding if necessary preparing surface by throughly cleaning of oil, grease, dirt and other material and fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) preparing as required, etc. complete.
A) Ground Floor Bamboowood 10mm thick Wall Cladding including Threshold & T-mold - Providing & fixing in position Phenol bonded Bamboowood wall cladding at all height with planks of sizes 10mm thick, 1900mm length (minimum) and 135mm wide approved colour, texture and finish, having Performance Appraisal Certificate (PAC) issued by Building materials & Technology Promotion Council (BMTPC). with necessary profiled edges fixed with BR nails to frame work made of second class teak wood of size 50 x 50mm in centre and ends of Number tile. The bamboowood cladding shall be laid over teak wood frame and hold in place by 50mm thick teak wood placed in centre of two teak wood and backlayment and covered with 1.00mm thick expanded poly ethylene foam of density 25Kilogram/cum in two layers first layer on wall surface before fixing wooden frame and second layer on frame under cladding. The Bamboowood planks shall have minimum density of 1000 Kilogram/cum & minimum Hardness 1000 Kilogramf. with Eco friendly UV coating, all complete as per direction of Engineer in-charge.
A) Ground Floor Providing and laying telephone black / Amba White / Cadburybrown / Ruby red / Ocean Brown granite stone of 18 to 20 mm thick for door frame/ dado/ window boxing etc. On C.M. 1:6 including filling joints with polymer base filler nosing/moulding the sharp edges wherever necessary, curing, etc. complete.
B) First Floor Providing and laying telephone black / Amba White / Cadburybrown / Ruby red / Ocean Brown granite stone of 18 to 20 mm thick for door frame/ dado/ window boxing etc. On C.M. 1:6 including filling joints with polymer base filler nosing/moulding the sharp edges wherever necessary, curing, etc. complete.
A) Ground Floor Providing and fixing 900mm high S.S.304 Grade Stainless steel railing with 40mm diameter and 1.5mm thick at top,40mm diameter and 1.5mm thick vertical supports spaced at 1.5m center to center and 8mm thick toughened glass including fabricating ,fixtures, errecting , necessary welding , grinding , finishing, buffing to stainless steel pipe etc. complete
B) First Floor Providing and fixing 900mm high S.S.304 Grade Stainless steel railing with 40mm diameter and 1.5mm thick at top,40mm diameter and 1.5mm thick vertical supports spaced at 1.5m center to center and 8mm thick toughened glass including fabricating ,fixtures, errecting , necessary welding , grinding , finishing, buffing to stainless steel pipe etc. complete
A) Ground Floor Providing and fixing in position (as per 1868 / 1982) Alluminium sliding window of threetracks with rectangular pipe 95 x 38.10 x 0.90 mm at weight 0.637 Kilogram/Running metre.with window frame bottom track section 92 x 31.75 x 1.30 mm at weight 1.070Kilogram/Running metre.. Top and side track section 92 x 31.75 x 1.30 mm at weight 0.933Kilogram/Running metre. The shutter should be of bearing bottom 40 x 18 x 1.25 mm atweight 0.417 Kilogram/Running metre. Inter locking section 40 x 18 x 1.10 mm at weight0.469 Kilogram/Running metre. and handle and top section 40 x 18 x 1.25 mm at weighto.417 Kilogram/Running metre. As per detailed drawings and as directed byEngineerincharge with all necessary Aluminium sections fixtures and fastenings such as rollerbearing in nylon casting and self locking catch fitted in vertical section of shutter including 5mm thick plain glass and aluminium mosquito net shutter with stainless steel jail with allrequired screws and nuts etc, complete. With colour Anodising with box
B) First Floor Providing and fixing in position (as per 1868 / 1982) Alluminium sliding window of threetracks with rectangular pipe 95 x 38.10 x 0.90 mm at weight 0.637 Kilogram/Running metre.with window frame bottom track section 92 x 31.75 x 1.30 mm at weight 1.070Kilogram/Running metre.. Top and side track section 92 x 31.75 x 1.30 mm at weight 0.933Kilogram/Running metre. The shutter should be of bearing bottom 40 x 18 x 1.25 mm atweight 0.417 Kilogram/Running metre. Inter locking section 40 x 18 x 1.10 mm at weight0.469 Kilogram/Running metre. and handle and top section 40 x 18 x 1.25 mm at weighto.417 Kilogram/Running metre. As per detailed drawings and as directed byEngineerincharge with all necessary Aluminium sections fixtures and fastenings such as rollerbearing in nylon casting and self locking catch fitted in vertical section of shutter including 5mm thick plain glass and aluminium mosquito net shutter with stainless steel jail with allrequired screws and nuts etc, complete. With colour Anodising with box
C) Second Floor Providing and fixing in position (as per 1868 / 1982) Alluminium sliding window of threetracks with rectangular pipe 95 x 38.10 x 0.90 mm at weight 0.637 Kilogram/Running metre.with window frame bottom track section 92 x 31.75 x 1.30 mm at weight 1.070Kilogram/Running metre.. Top and side track section 92 x 31.75 x 1.30 mm at weight 0.933Kilogram/Running metre. The shutter should be of bearing bottom 40 x 18 x 1.25 mm atweight 0.417 Kilogram/Running metre. Inter locking section 40 x 18 x 1.10 mm at weight0.469 Kilogram/Running metre. and handle and top section 40 x 18 x 1.25 mm at weighto.417 Kilogram/Running metre. As per detailed drawings and as directed byEngineerincharge with all necessary Aluminium sections fixtures and fastenings such as rollerbearing in nylon casting and self locking catch fitted in vertical section of shutter including 5mm thick plain glass and aluminium mosquito net shutter with stainless steel jail with allrequired screws and nuts etc, complete. With colour Anodising with box
A) Ground Floor Providing and fixing in position powder coated aluminium louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38 mm x 1.22 mm box type, 5 mm thick sheet glass louvers, of approved quality etc. complete.
B) First Floor Providing and fixing in position powder coated aluminium louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38 mm x 1.22 mm box type, 5 mm thick sheet glass louvers, of approved quality etc. complete.
C) Second Floor Providing and fixing in position powder coated aluminium louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38 mm x 1.22 mm box type, 5 mm thick sheet glass louvers, of approved quality etc. complete.
A) Ground Floor Providing and fixing mild steel grill work for windows, ventilators etc. 20 Kilogram/Square Metre as per drawing including fixtures, necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting complete.
B) First Floor Providing and fixing mild steel grill work for windows, ventilators etc. 20 Kilogram/Square Metre as per drawing including fixtures, necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting complete.
C) Second Floor Providing and fixing mild steel grill work for windows, ventilators etc. 20 Kilogram/Square Metre as per drawing including fixtures, necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting complete.
A) Ground Floor Providing and fixing M.S. grill door 24 Kilogram/Square Metre of various size as per detailed drawings without hot dip coating, iron fixtures and fastenings and 3 coats of oil painting etc
A) Ground Floor providing and fixing frame with / without ventilator of size as specified with Country cut teak wood for doors and windows including chamfering, rounding, rebating, iron holdfast of size 300mm x 40mm x 5mm with oil painting, etc. complete
B) First Floor providing and fixing frame with / without ventilator of size as specified with Country cut teak wood for doors and windows including chamfering, rounding, rebating, iron holdfast of size 300mm x 40mm x 5mm with oil painting, etc. complete
C) Second Floor providing and fixing frame with / without ventilator of size as specified with Country cut teak wood for doors and windows including chamfering, rounding, rebating, iron holdfast of size 300mm x 40mm x 5mm with oil painting, etc. complete
A) Ground Floor Providing and fixing Country cut teak wood single leaf panelled door shutter without fanlightand 25mm thick as per drawing consisting of T.W. top rail size 100mm x 25mm and bottomlock rail 200mm x 25mm insert pannel 12 mm thick commercial ply faced T.W. particleboard with phenol formaldehyde synthetic resin (Generally confirming to ISI 3097) excludingframe, including stainless steel fixture and fastening and T.W. beading to junctions ofpanelled inserts and as instructed by the Engineer in charge including 3 coats of oil painting etc. complete.
A) Ground Floor Supply, fixing and installation of 4mm thick Aluminium Composite Panel (ACP) of approvedcolour for external cladding in combination of solid and metallic colours, including allnecessary Framework, support and complete weather sealing as per architectural drawing. TheAluminium Composite Panel (ACP) should be made out of thermoplastic core of low-densitypolyethylene LDPE (100% virgin mix), sandwiched between two aluminium sheets ofALLOY GRADE- 5000 series, Number not less than 0.50 mm thick, total thickness ofaluminium composite panels not to be less than 4 mm, the exposed surface thereof shall haveStove lacquered finishing coat not less than (26 + - 2) micron (containing minimum 70%kynar 500 based PVDF) of colour and shade as per architectural design. The inside surface(facing the building exterior surface)shall have polyster based powder coating not less than 25Micron with protective peel-off foil on the exterior face (peel off film will in no case leaveany adhesive mark over the composite panel surface after it is peeled off). The supportingframework shall be made out of 50 mm X25mm X 3mm thick Aluminium section to bespaced horizontally and vertically for fixing of panel of size 900 mm X 1200 mm and fixed tothe building structure as per design through 50mm X50mm X5 mm MS angle clamps prefixedto masonry or slab, columns with Hilti make anchor fastener screws. The fixing of panel to bedone with the help of VHB tapes and screws and all the sealing of joints to be done withweather sealent Silicon as directed by Engineer-in-charge. (Prior permission of S.E. isnecessary before inclusion of this item in estimate)
A) Ground Floor Providing structural steel work in trusses, other similar trussed purlins and members with all bracing, gusset plates etc. as per detailed designs and drawings or as directed including cutting, fabricating, hoisting, erecting fixing in position, Making riveted/ bolted/ welded connection and one coat of anticorrosive paint and over it 2 coats of oil painting approved quality and shade etc. complete.
A) Ground Floor Providing and fixing colour coated Zincalume ( R ) AZ150 ( min 150 gms/sq.mt. total onNumber side ) profiled sheets for roofing. The feed material is manufactured out of nominal 0.45mm Base Metal Thickness ( BMT ) (0.5 mm TCT ), Hi-strength steel with min.550 MPa yieldstrength, metallic hot dip coated with Aluminium-Zinc alloy (55% aluminium 43.4% zinc1.6% silicon) with COLORBOND ( R ) steel quality super durable polyester paint coat ( withinorganic pigment). The paint shall have a total coating thickness of nominal 35 um,comprising of nominal 25 um exterior coat on top surface and nominal 10 um reverse coat onback surface. Profile sheet shall have nom. 950-1050 mm effective cover width and nominal25-30 mm deep ribs with subtle square fluting in the five pan at nominal 180-250 mm centerto-center. The end rib shall be designed for anti-capillary groove. and return leg. The feedmaterial should have coil manufacturers product details marked a regular interval. Includingfasteners with min. fastened with min. 25 um Zinc-Tin alloy coated, Hex head, self-drillingscrew etc. complete. (weight of profile 4.52 Kilogram/Square Metre)
A) Ground Floor Providing and Fixing Rollar Blinds AMI Make or approved make & shade of 38mm round Aluminium channel with Blackout fabric & telting with chain (Ball) system with all necessary fixtures and fitting etc. complete. (Sample to be final by Engineer In-charge prior execution of work)
A) Ground Floor Providing and fixing in position Gypsum board false ceiling with 12.5 mm thick Gypsumboards, screwed/fixed to the under structure of suspended G.I. Grid constructed andsuspended from the main ceiling consisting of ceiling sections of size 25 x 50 mm maximumcenter to center distance of 600 milimetre perimeter channel and intermediate channels atmaximum center to center distance 1200 milimetre galvanized grid should be fixed toreinforced cement concrete slab. The gypsum board should be fixed to galvanized iron gridwith necessary screws. The boards should be taped and filled from underside to give smooth,seamless ceiling. The rate should include necessary additional ceiling sections andintermediate channels. Additional intermediate channels should be fixed to strap hangers foradditional support to prevent strapping at every 1200 milimetre item to be completed in allrespect including necessary sleeves for ducts finishing of joints cut outs, painting includinglabour, material, lifts etc. all complete.
B) First Floor Providing and fixing in position Gypsum board false ceiling with 12.5 mm thick Gypsumboards, screwed/fixed to the under structure of suspended G.I. Grid constructed andsuspended from the main ceiling consisting of ceiling sections of size 25 x 50 mm maximumcenter to center distance of 600 milimetre perimeter channel and intermediate channels atmaximum center to center distance 1200 milimetre galvanized grid should be fixed toreinforced cement concrete slab. The gypsum board should be fixed to galvanized iron gridwith necessary screws. The boards should be taped and filled from underside to give smooth,seamless ceiling. The rate should include necessary additional ceiling sections andintermediate channels. Additional intermediate channels should be fixed to strap hangers foradditional support to prevent strapping at every 1200 milimetre item to be completed in allrespect including necessary sleeves for ducts finishing of joints cut outs, painting includinglabour, material, lifts etc. all complete.
A) Ground Floor Providing and Fixing of GI Lay in Plain metal ceiling consisting of 600x600mm Lay in tiles of pre coated galvanized steel in 0.5 mm thickness in Global white color tile to be laid on grid systems with 15mm wide T - section flanges color white having rotary stitching on the Main Runner, 1200 mm and 600 mm Cross Tees.Providing and Fixing of GI Lay in Plain metal ceiling consisting of 600x600mm Lay in tiles of pre coated galvanized steel in 0.5 mm thickness in Global white color tile to be laid on grid systems with 15mm wide T - section flanges color white having rotary stitching on the Main Runner, 1200 mm and 600 mm Cross Tees.products approved as per GRIHA and BS 476 etc. complete.
B) First Floor Providing and Fixing of GI Lay in Plain metal ceiling consisting of 600x600mm Lay in tiles of pre coated galvanized steel in 0.5 mm thickness in Global white color tile to be laid on grid systems with 15mm wide T - section flanges color white having rotary stitching on the Main Runner, 1200 mm and 600 mm Cross Tees.Providing and Fixing of GI Lay in Plain metal ceiling consisting of 600x600mm Lay in tiles of pre coated galvanized steel in 0.5 mm thickness in Global white color tile to be laid on grid systems with 15mm wide T - section flanges color white having rotary stitching on the Main Runner, 1200 mm and 600 mm Cross Tees.products approved as per GRIHA and BS 476 etc. complete.
A) Ground Floor Providing and fixing Indian teak wood plank ceiling 20 mm thick plain underside tonguedand grooved including iron screws, scaffolding, if necessary, including one primer coat onunder side and one coat of coal tar on upper side etc. complete
B) First Floor Providing and fixing Indian teak wood plank ceiling 20 mm thick plain underside tonguedand grooved including iron screws, scaffolding, if necessary, including one primer coat onunder side and one coat of coal tar on upper side etc. complete
A) Ground Floor Providing and laying cement concrete pipe of IS 458:2003 NP-2 class of 600mm diameter in proper line, level and slope including providing and fixing collars in cement mortar 1:2 and curing etc. complete
A) Ground Floor Providing and laying chequered tiles of approved quality of size 30 cm x 30 cm, confirmingto corresponding I.S. for flooring in required position laid on a bed of 1:4 cement mortarincluding cement float, filling joint with cement slurry cleaning curing etc. complete
A) Ground Floor Providing and casting in situ or precast tapering R.C.C. M-20 Semi Barrier type Kerb without gutter ( as per IRC 86 1983) embedded 125mm below ground level over M-10 PCC finished neatly with C.M. 1:2, setting the same in C.M. 1:2, including the required excavation in any strata and removing the excavated stuff any where in city and redoing the surface as specified and directed by Engineering In-charge. Using Concrete Batching and Mixing Plant
GROUND FLOOR Providing and fixing European type wall¬hung white water closet of Paryware / Hindware with push valve concealed type with cover plate 32mm size of including soil pipe ,vent pipe up to outside face of wall ,100mm dia. G.I. plug bend inlet pipe all fittings, cutting& making good walls, floors etc. complete.
FIRST FLOOR Providing and fixing European type wall¬hung white water closet of Paryware / Hindware with push valve concealed type with cover plate 32mm size of including soil pipe ,vent pipe up to outside face of wall ,100mm dia. G.I. plug bend inlet pipe all fittings, cutting& making good walls, floors etc. complete.
SECOND FLOOR Providing and fixing European type wall¬hung white water closet of Paryware / Hindware with push valve concealed type with cover plate 32mm size of including soil pipe ,vent pipe up to outside face of wall ,100mm dia. G.I. plug bend inlet pipe all fittings, cutting& making good walls, floors etc. complete.
GROUND FLOOR Providing and fixing C.P.Two way BIB cock of approved make continental including necessary sockets/union nut etc. complete.
FIRST FLOOR Providing and fixing C.P.Two way BIB cock of approved make continental including necessary sockets/union nut etc. complete.
SECOND FLOOR Providing and fixing C.P.Two way BIB cock of approved make continental including necessary sockets/union nut etc. complete.
GROUND FLOOR Providing and fixing Shower Head, with shower arm of approved make mixer of all necessary pipe fittings and connections etc. complete as directed by Engineer in charge
FIRST FLOOR Providing and fixing Shower Head, with shower arm of approved make mixer of all necessary pipe fittings and connections etc. complete as directed by Engineer in charge
SECOND FLOOR Providing and fixing Shower Head, with shower arm of approved make mixer of all necessary pipe fittings and connections etc. complete as directed by Engineer in charge
GROUND FLOOR Providing and fixing Hand shower (health faucet) with 8mm dia. 1m long flexible tube having wall hook with approved make including necessary sockets/ union nut etc. complete as directed by Engineer in charge.
FIRST FLOOR Providing and fixing Hand shower (health faucet) with 8mm dia. 1m long flexible tube having wall hook with approved make including necessary sockets/ union nut etc. complete as directed by Engineer in charge.
SECOND FLOOR Providing and fixing Hand shower (health faucet) with 8mm dia. 1m long flexible tube having wall hook with approved make including necessary sockets/ union nut etc. complete as directed by Engineer in charge.
SECOND FLOOR Providing and fixing white glazed urinal of series with Pressmatic auto closing valve of having 32mm diameter P.V.C. flush pipe with fitting and flushing of approved make and arrangement including lead soil pipe, lead trap & soil pipe connection upto the outside face of wall etc.complete as directed by Engineer in charge.
GROUND FLOOR Providing and fixing 450mm x 550mm size superior type Belgium mirror with 16mm dia. nickel plated towel rod etc. complete.
FIRST FLOOR Providing and fixing 450mm x 550mm size superior type Belgium mirror with 16mm dia. nickel plated towel rod etc. complete.
SECOND FLOOR Providing and fixing 450mm x 550mm size superior type Belgium mirror with 16mm dia. nickel plated towel rod etc. complete.
GROUND FLOOR Providing and fixing chromium plated towel rod 16 mm dia and 75 cm. in length including all accessories complete..
FIRST FLOOR Providing and fixing chromium plated towel rod 16 mm dia and 75 cm. in length including all accessories complete..
SECOND FLOOR Providing and fixing chromium plated towel rod 16 mm dia and 75 cm. in length including all accessories complete..
GROUND FLOOR Providing and fixing C.P.soap dish (polyurethane)
FIRST FLOOR Providing and fixing C.P.soap dish (polyurethane)
SECOND FLOOR Providing and fixing C.P.soap dish (polyurethane)
GROUND FLOOR Providing and fixing White glazed with bottle trap earthenware Wash Hand Basin of 55x40 cm size including cold water piller taps, brackets, rubber plugs and brass chain, stop tap, chromium plate bottle trap and necessary pipe connections including UPAC waste pipe and trap upto the outside face of the wall, making good the damaged surface, testing etc. complete.
FIRST FLOOR Providing and fixing White glazed with bottle trap earthenware Wash Hand Basin of 55x40 cm size including cold water piller taps, brackets, rubber plugs and brass chain, stop tap, chromium plate bottle trap and necessary pipe connections including UPAC waste pipe and trap upto the outside face of the wall, making good the damaged surface, testing etc. complete.
SECOND FLOOR Providing and fixing White glazed with bottle trap earthenware Wash Hand Basin of 55x40 cm size including cold water piller taps, brackets, rubber plugs and brass chain, stop tap, chromium plate bottle trap and necessary pipe connections including UPAC waste pipe and trap upto the outside face of the wall, making good the damaged surface, testing etc. complete.
GROUND FLOOR Providing and fixing 15 cm rigid PVC Nahani trap including PVC grating ,bend,connectingpiece of UPVC pipe up to the outside face of wall ,making the good damaged surface and testing etc. complete ( Prior approval of sample and brand by Ex. Engr. is necessary before use)
FIRST FLOOR Providing and fixing 15 cm rigid PVC Nahani trap including PVC grating ,bend,connectingpiece of UPVC pipe up to the outside face of wall ,making the good damaged surface and testing etc. complete ( Prior approval of sample and brand by Ex. Engr. is necessary before use)
SECOND FLOOR Providing and fixing 15 cm rigid PVC Nahani trap including PVC grating ,bend,connectingpiece of UPVC pipe up to the outside face of wall ,making the good damaged surface and testing etc. complete ( Prior approval of sample and brand by Ex. Engr. is necessary before use)
GROUND FLOOR Providing and fixing 100 mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete..
FIRST FLOOR Providing and fixing 100 mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete..
SECOND FLOOR Providing and fixing 100 mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete..
GROUND FLOOR Providing and fixing 75 mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete
FIRST FLOOR Providing and fixing 75 mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete
SECOND FLOOR Providing and fixing 75 mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete
GROUND FLOOR Providing , laying and fixing P.V.C. pipe of 50 mm dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.
FIRST FLOOR Providing , laying and fixing P.V.C. pipe of 50 mm dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.
SECOND FLOOR Providing , laying and fixing P.V.C. pipe of 50 mm dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.
GROUND FLOOR Providing and fixing on walls/ceiling/floor 20 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.
FIRST FLOOR Providing and fixing on walls/ceiling/floor 20 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.
SECOND FLOOR Providing and fixing on walls/ceiling/floor 20 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.
GROUND FLOOR Providing and fixing on walls/ ceiling/ floor 25 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.
FIRST FLOOR Providing and fixing on walls/ ceiling/ floor 25 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.
SECOND FLOOR Providing and fixing on walls/ ceiling/ floor 25 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.
GROUND FLOOR Providing and fixing on walls/ ceiling/ floor 32 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.
FIRST FLOOR Providing and fixing on walls/ ceiling/ floor 32 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.
SECOND FLOOR Providing and fixing on walls/ ceiling/ floor 32 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.
GROUND FLOOR Providing and fixing on walls /ceiling/ floor 40 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.
FIRST FLOOR Providing and fixing on walls /ceiling/ floor 40 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.
SECOND FLOOR Providing and fixing on walls /ceiling/ floor 40 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.
GROUND FLOOR Providing and fixing on walls/ ceiling/ floor 50 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete.
FIRST FLOOR Providing and fixing on walls/ ceiling/ floor 50 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete.
SECOND FLOOR Providing and fixing on walls/ ceiling/ floor 50 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete.
GROUND FLOOR Providing and fixing 40 mm. dia Ball cock medium type with PVC float including sockets and necessary fittings and tested as per municipal requirements etc. complete.
SECOND FLOOR Providing and fixing Ball Cock for 32 mm with necessary fittings.
GROUND FLOOR Providing and fixing Ball Valve for 50 mm with necessary fittings.
FIRST FLOOR Providing and fixing Ball Valve for 50 mm with necessary fittings.
SECOND FLOOR Providing and fixing Ball Valve for 50 mm with necessary fittings.
GROUND FLOOR Providing and fixing C.P. Angular stop clock with wall flange of approved make continentalincluding necessary sockets/union nut etc. complete.
FIRST FLOOR Providing and fixing C.P. Angular stop clock with wall flange of approved make continentalincluding necessary sockets/union nut etc. complete.
SECOND FLOOR Providing and fixing C.P. Angular stop clock with wall flange of approved make continentalincluding necessary sockets/union nut etc. complete.
GROUND FLOOR Providing and fixing Strainer for 50 mm with necessary fittings.
FIRST FLOOR Providing and fixing Strainer for 50 mm with necessary fittings.
SECOND FLOOR Providing and fixing Strainer for 50 mm with necessary fittings.
GROUND FLOOR Providing and fixing 45 cm wide mild steel ladder of 40mm x 6 mm mild steel flat stringers and steps of 18 mm dia. mild steel bar for water tank including fixing it in (1:2:4) M-15 cement concrete block 60cm x 30cm x 30cm and painting the ladder complete. (Anti Corossive Paint)
FIRST FLOOR Providing and fixing 45 cm wide mild steel ladder of 40mm x 6 mm mild steel flat stringers and steps of 18 mm dia. mild steel bar for water tank including fixing it in (1:2:4) M-15 cement concrete block 60cm x 30cm x 30cm and painting the ladder complete. (Anti Corossive Paint)
SECOND FLOOR Providing and fixing 45 cm wide mild steel ladder of 40mm x 6 mm mild steel flat stringers and steps of 18 mm dia. mild steel bar for water tank including fixing it in (1:2:4) M-15 cement concrete block 60cm x 30cm x 30cm and painting the ladder complete. (Anti Corossive Paint)
GROUND FLOOR Providing and fixing 100 mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete..
FIRST FLOOR Providing and fixing 100 mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete..
SECOND FLOOR Providing and fixing 100 mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete..
GROUND FLOOR Providing and Fixing toilet set for differently Abled persons consist of Floor Mounted white vitreous china water Closet including 6 litre capacity white vitreous china flushing Cistern with raised soft-push button,white vitreous china wash basin of size 46x36 cm and one no SS304 hinge drail 76 cms & three no SS304 of (Grab Bar) 60 cm sall including cutting and making good the walls and floors wherever required, seat cover, cistern & washbasin fittings,nuts, bolts and gasket etc complete as per the direction of Engineer-In-charge.
A) Ground Floor Providing & fixing 39 / 40 mm thick sandwiched type flush door shutter by using 18 mm thick x 2 commercial plywood of exterior grade as per detailed drawings with 1.50 mm thick approved laminated on both faces of shutter or as directed, all necessary bends, T.W. lipping & moldings, stainless steel fixtures & fastenings, with both side SS/ Hdrop for lock, stainless steel handles on both sides, finishing with melamine polish to four edges etc. complete. (Ply 18 x 2 =36mm + laminate 1.50 x 2 =3 mm = Total 39mm)
B) First Floor Providing & fixing 39 / 40 mm thick sandwiched type flush door shutter by using 18 mm thick x 2 commercial plywood of exterior grade as per detailed drawings with 1.50 mm thick approved laminated on both faces of shutter or as directed, all necessary bends, T.W. lipping & moldings, stainless steel fixtures & fastenings, with both side SS/ Hdrop for lock, stainless steel handles on both sides, finishing with melamine polish to four edges etc. complete. (Ply 18 x 2 =36mm + laminate 1.50 x 2 =3 mm = Total 39mm)
C) Second Floor Providing & fixing 39 / 40 mm thick sandwiched type flush door shutter by using 18 mm thick x 2 commercial plywood of exterior grade as per detailed drawings with 1.50 mm thick approved laminated on both faces of shutter or as directed, all necessary bends, T.W. lipping & moldings, stainless steel fixtures & fastenings, with both side SS/ Hdrop for lock, stainless steel handles on both sides, finishing with melamine polish to four edges etc. complete. (Ply 18 x 2 =36mm + laminate 1.50 x 2 =3 mm = Total 39mm)
A) Ground Floor Providing and fixing machine cut polished 18 to 20mm thick telephone black/Amba white/Cat bary brown/RBI Card/Ocean brown granote stones for Treads & Riser of stair Steps/Enterance steps of approved colour and shade with double granite (Sandwitched Type) Full moulding/Nosing for the treads on bed of 1:4 cement mortar including float filling joints with neat cement slurry,Curing,Polishing,Polishing to full moulding,and cleaing etc.Complete
B) First Floor Providing and fixing machine cut polished 18 to 20mm thick telephone black/Amba white/Cat bary brown/RBI Card/Ocean brown granote stones for Treads & Riser of stair Steps/Enterance steps of approved colour and shade with double granite (Sandwitched Type) Full moulding/Nosing for the treads on bed of 1:4 cement mortar including float filling joints with neat cement slurry,Curing,Polishing,Polishing to full moulding,and cleaing etc.Complete
A) Ground Floor Supplying, & fixing in position aluminium fins of 1000X50x25 mm with special locking system designed by Elegance architerural products supported by 38x38mm L-Angle with pre-punchated hole as per approved gap horizontal carriers both, having thickness of 1mm and a clear gap of 50mm between verical members as per pattern,choice of colour,finish, etc. as shown in approved drawing and as instructed by site Incharge. Rates shall be inclusive of supply & fixing using 1mm thick L-clit of dim. 50mm X 50mm X 50mm & SS-screws), application of powder coating, cutting, making, fixing, transportation, loading, unloading, lifting, shifting, saftey precautions etc. all complete.
B) First Floor Supplying, & fixing in position aluminium fins of 1000X50x25 mm with special locking system designed by Elegance architerural products supported by 38x38mm L-Angle with pre-punchated hole as per approved gap horizontal carriers both, having thickness of 1mm and a clear gap of 50mm between verical members as per pattern,choice of colour,finish, etc. as shown in approved drawing and as instructed by site Incharge. Rates shall be inclusive of supply & fixing using 1mm thick L-clit of dim. 50mm X 50mm X 50mm & SS-screws), application of powder coating, cutting, making, fixing, transportation, loading, unloading, lifting, shifting, saftey precautions etc. all complete.
C) Second Floor Supplying, & fixing in position aluminium fins of 1000X50x25 mm with special locking system designed by Elegance architerural products supported by 38x38mm L-Angle with pre-punchated hole as per approved gap horizontal carriers both, having thickness of 1mm and a clear gap of 50mm between verical members as per pattern,choice of colour,finish, etc. as shown in approved drawing and as instructed by site Incharge. Rates shall be inclusive of supply & fixing using 1mm thick L-clit of dim. 50mm X 50mm X 50mm & SS-screws), application of powder coating, cutting, making, fixing, transportation, loading, unloading, lifting, shifting, saftey precautions etc. all complete.
A) Ground Floor Providing and fixing horizontal level Armstrong Cellio Open cell GI lay-in ceiling tiles with border panels forming board edge of size 600x600x38mm (Nominal) having cell size of 150x150mm made of 120 gsm galvanized steel as per IS 277 (2003) suitable for architectural finishes in 0.35mm thickness as per in IS:513 (1994)in Global white color. The tile shall be electrostatically polyester powder coated using RoHS compliant powder having coating thickness ranging from 60-80 microns. The powder coating shall pass Salt Spray Test for 750 hours as per ASTM B117, QUV –A Test for 1000 hours as per ASTM G-154 – (Cycle – 1) and Humidity test for 1000 hours as per DIN 50017. The powder coating shall have an adhesion of GT0 as per EN ISO 2409. The shade variation across batches shall be delta E<1 using Excite/BYK Gardner instrument and gloss level of 25±5% at 60˚ as per ASTM D523. Tile shall have a Fire Performance class A1 as per EN-13964.Properties of Tile Relevant Standards10-07-2021: Base MAterial 120 gsm Galvanised Steel IS 277 (2003 ) Galvanization Panel Dimensions 600x600x38mm(Nominal)/594x594x38mm (Actual) Panel Thickness 0.35 mm IS:513(1994) thickness, Cell Size 150x150mm, Panel Fiish Electrostatically polyster powder coated using RoHS Compliant powder having coating thickness ranging from 60-80 Microns. Salt Spray Tested for 750 hours/ QUV –A Test for 1000 hours/ Humidity test for 1000 hours . Adhesion of GT0 as per EN ISO 2409. The shade variation within a manufacture batche shall be delta E<1 using Excite/BYK Gardner instrument and gloss level of 25±5% at 60˚ASTM B117(Salt Spray Test ) ASTM G-154 - (Cycle-1)(QUV-A test), DIN 50017 (Humidity Test ) EN ISO 2409 ( Adhesion ),ASTM D 523 (Gloss) Fire Property Class A1 EN-13964 .
B) First Floor Providing and fixing horizontal level Armstrong Cellio Open cell GI lay-in ceiling tiles with border panels forming board edge of size 600x600x38mm (Nominal) having cell size of 150x150mm made of 120 gsm galvanized steel as per IS 277 (2003) suitable for architectural finishes in 0.35mm thickness as per in IS:513 (1994)in Global white color. The tile shall be electrostatically polyester powder coated using RoHS compliant powder having coating thickness ranging from 60-80 microns. The powder coating shall pass Salt Spray Test for 750 hours as per ASTM B117, QUV –A Test for 1000 hours as per ASTM G-154 – (Cycle – 1) and Humidity test for 1000 hours as per DIN 50017. The powder coating shall have an adhesion of GT0 as per EN ISO 2409. The shade variation across batches shall be delta E<1 using Excite/BYK Gardner instrument and gloss level of 25±5% at 60˚ as per ASTM D523. Tile shall have a Fire Performance class A1 as per EN-13964.Properties of Tile Relevant Standards10-07-2021: Base MAterial 120 gsm Galvanised Steel IS 277 (2003 ) Galvanization Panel Dimensions 600x600x38mm(Nominal)/594x594x38mm (Actual) Panel Thickness 0.35 mm IS:513(1994) thickness, Cell Size 150x150mm, Panel Fiish Electrostatically polyster powder coated using RoHS Compliant powder having coating thickness ranging from 60-80 Microns. Salt Spray Tested for 750 hours/ QUV –A Test for 1000 hours/ Humidity test for 1000 hours . Adhesion of GT0 as per EN ISO 2409. The shade variation within a manufacture batche shall be delta E<1 using Excite/BYK Gardner instrument and gloss level of 25±5% at 60˚ASTM B117(Salt Spray Test ) ASTM G-154 - (Cycle-1)(QUV-A test), DIN 50017 (Humidity Test ) EN ISO 2409 ( Adhesion ),ASTM D 523 (Gloss) Fire Property Class A1 EN-13964 .
A) Ground Floor Providing and fixing aluminium system anodized sliding window of various sizes. Sliding will be made from Geeta / Blueshield 25 mm slim series or equivalent system. Windows will be of specially extruded aluminium 3 Track 2 Glass + 1 net shutter, track joints will be of 45 degree joints, joints will be fixed with specially developed clits. Track frame will be fixed to the masonary opening of windows with S.S 202 wood screws. Glass shutter will be made from specially extruded aluminium section , Glass considered is 5mm clear toughened glass. All shutter will be having 45 degree joints, joints will be fixed with specially developed clits to form uniform hairline joints. All shutter will be fixed to main frame with neccessary double roller to have smooth and easy movement of shutter. shutters will have single point self pressing lock. All fixing screws will be of S.S 202. Windows will be sealed with weather sealant from outer periphery,etc.complete
A) Ground Floor Providing and fixing aluminium system anodized fixed window of various sizes. Casement will be made from Geeta / Blueshield 40 mm series or equivalent System. Windows will be of specially extruded aluminium section, joints will be of 45 degree joints, joints will be fixed with specially developed clits. Track frame will be fixed to the masonry opening of windows with S S 202 wood screws. Fixed glass casement will be made from specially extruded aluminum section, glass considered is 5 mm clear toughened glass. All shutter will be having 45 degree joints, joints will be fixed with specially developed clits to form uniform hairline joint. All fixing screws will be of S S 202. Windows will be sealed with weather sealant from outer periphery, etc. complete.
A) Ground Floor Providing & fixing Fabricated Tubular steel grilled openable gate supported by 219.10 mm dia. M.S. pipe columns, fabricated by using steel pipes, m.s. flat , m.s. plate as per detailed drawing including extra heavy fabricated hinges, locking arrangement, all necessary including cutting, fabricating, hoisting, erecting, fixing in position, making riveted/bolted/ welded connections and painting complete
A) Ground Floor Providing and fixing M.S.Pipe railing consisting of hand rail 60.30mm outer diameter confirming 3.60kg/m vertically supported by 25x5 M.S.Flats at & having base 25x5mm M.S.Flat on constructed RCC Pardi/BB Wall as per detailed drawing & design including fabrication,Cutting, Welding,Grinding,& Fixing with one coat of primer & two coats of synthetic enamel paint of approved shade etc.Complete For Rate Analysis Consider length 3.00m
B) First Floor Providing and fixing M.S.Pipe railing consisting of hand rail 60.30mm outer diameter confirming 3.60kg/m vertically supported by 25x5 M.S.Flats at & having base 25x5mm M.S.Flat on constructed RCC Pardi/BB Wall as per detailed drawing & design including fabrication,Cutting, Welding,Grinding,& Fixing with one coat of primer & two coats of synthetic enamel paint of approved shade etc.Complete For Rate Analysis Consider length 3.00m
C) Second Floor Providing and fixing M.S.Pipe railing consisting of hand rail 60.30mm outer diameter confirming 3.60kg/m vertically supported by 25x5 M.S.Flats at & having base 25x5mm M.S.Flat on constructed RCC Pardi/BB Wall as per detailed drawing & design including fabrication,Cutting, Welding,Grinding,& Fixing with one coat of primer & two coats of synthetic enamel paint of approved shade etc.Complete For Rate Analysis Consider length 3.00m
A) Ground Floor Providing & Fixing powder coated G.I. with Glazed openable door shutters (French door type) with frame consisting of 125x60mm G I Box type frame by using 18 gauge G.I.sheet including all necessary hold fasts etc, and openable ( folding /french type ) 22 gauge G.I.Section pressed in various profiles (Z,T etc.) , including providing 10mm Sq.gaurd bars and 5 mm thick plain glass, standard stainless steel fittings (aldrop,tower bolt,hinges , etc.) inclusive all Lobour,material,Transportation ,fixing on site with attractive powder coating finish to GI section etc. Complete
B) First Floor Providing & Fixing powder coated G.I. with Glazed openable door shutters (French door type) with frame consisting of 125x60mm G I Box type frame by using 18 gauge G.I.sheet including all necessary hold fasts etc, and openable ( folding /french type ) 22 gauge G.I.Section pressed in various profiles (Z,T etc.) , including providing 10mm Sq.gaurd bars and 5 mm thick plain glass, standard stainless steel fittings (aldrop,tower bolt,hinges , etc.) inclusive all Lobour,material,Transportation ,fixing on site with attractive powder coating finish to GI section etc. Complete
C) Second Floor Providing & Fixing powder coated G.I. with Glazed openable door shutters (French door type) with frame consisting of 125x60mm G I Box type frame by using 18 gauge G.I.sheet including all necessary hold fasts etc, and openable ( folding /french type ) 22 gauge G.I.Section pressed in various profiles (Z,T etc.) , including providing 10mm Sq.gaurd bars and 5 mm thick plain glass, standard stainless steel fittings (aldrop,tower bolt,hinges , etc.) inclusive all Lobour,material,Transportation ,fixing on site with attractive powder coating finish to GI section etc. Complete
A) Ground Floor GLASS DOOR- Providing and fixing glass door size 1.0m/1.2m x 2.7m single leaf shutter of 12 mm thick toughen glass frosting and edge polish as shown in the drawings or as directed, including all necessary fittings like hydraulic patch fitting, top patch fittings, Top pivot, door handle, door lock, door stopper, door soft central 180 weather seal for door edges etc. complete as directed by Engineer -IN-Charge.
A) Ground Floor Providing and fixing Aluminium colour Anodised Sliding Folding Door 3+1 Shutters having Special patented Frame & shutter profiles. Outer frame Profiles being fixed to the missionary with SS-202 Screws & shutters having 45 degree corner joints with special cleats for linear joints having 6mm toughened glass are installed in the frame structure with Mortise Lock at Opening , Top & Bottom pivots for sliding, but hinges for folding operation & subsidiary multi point locking & pop handle for additional security, Complete.
A) Ground Floor Providing and fixing collapsible steel gate in one / two leaves with hot rolled vertical channelsof 18 x 9 x 3 mm minimum size, crossings of M.S. flats of size 18 x 5 mm T or E section forrunner of minimum 40 x 6 mm size for flange, M.S. flat for top runner of minimum size 40 x12 mm with roller wheels confirming to grade F.G. 150 fitted with snap headed rivets ofminimum size 6 mm max. spacing of vertical channels be 100 mm enclosed gate position andclear space of 150 mm between two sets of crossings with hold fasts, stoppers, spaces,handles, locking arrangement and one coat of red lead primer and oil painting etc. complete.(I.S. 105211983)
A) Ground Floor Boom Barrier - Providing, supplying, installation & commissioning imported type or equivalent make boom barrier at entrance gate having clear opening width 3.50 m to 4.50 m including LED lighting system with variable flashing, three station push button fixed support, pair of photocells with anodized aluminum vertical mounting etc. also boom barrier comprising of white spray-painted aluminum boom with end cap & passive rubber safety edges and fixed support. Rabust spring balanced gear system, encoder-controlled movement, external manual release system with key operation including packaging charges, transportation, transit insurance, loading / unloading, installation on site, commissioning, warranty for automation system against manufacturing defect for a period of 12 months from the date of installation etc. complete. (excluding GST)
A) Ground Floor Providing and fixing P.V.C. Rain water pipes of 110mm outer diameter and having wallthickness of 2.2 to 2.7 mm confirming to I.S. 13592-1992 including proper rainwaterreceiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes, inludingfixing the pipe on wall using approved wooden cleats projecting 25mm to 40mm from face ofwall a fixing with clips of approved quality and number ,filing the joint using rubber gasketwith solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks,including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations ofpipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved fromengineer in charge etc. complete.
C) Second Floor Providing and fixing P.V.C. Rain water pipes of 110mm outer diameter and having wallthickness of 2.2 to 2.7 mm confirming to I.S. 13592-1992 including proper rainwaterreceiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes, inludingfixing the pipe on wall using approved wooden cleats projecting 25mm to 40mm from face ofwall a fixing with clips of approved quality and number ,filing the joint using rubber gasketwith solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks,including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations ofpipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved fromengineer in charge etc. complete.
A) Ground Floor Providing and Fixing of Mineral Fibre Board Acoustical Suspended Ceiling System with ultima (Bevelled Tegular) Edge Tiles of size 15mm Exposed GRID. The tiles should have Humidity Resistance (RH) of 99%, NRC 0.7, Light Reflectance 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Colour White, Fire Performance UK Class 0 / Class 1 (BS 476 pt - 6 &7) in module size of 600 x 600 x 20mm , suitable for Green Building application, with Recycled content of 32%. The tile shall be laid on precoated G.I.channel on XL2 Clip having a web height of 32 mm with 15 mm wide T - section flanges colour white having rotary stitching on all T sections i.e. the Main Runner, 1200 mm and 600 mm Cross Tees with a web height of 32 mm and a load carrying capacity of 7.7 Kilograms /M2 and minimum pull outstrength of 100 Kilograms.. The T Sections have a Galvanizing of 90 grams per M2 and need to be installed with Suspension system. The Tile and Grid system used together should carry a10 year warranty. products approved as per GRIHA and BS 476 etc. complete.
A) Ground Floor ACOUSTICAL WALL PANELLING – FABRIC WRAPPED OF SIZE: 600X600/1200X25MM Providing and Fixing of Acoustical Wall Panel with square edges made of fibre glass substrate 25mm thick, wrapped on the front side with an acoustically transparent fabric as per the approved shade (Husk, Copper, Sangria, Sesame, Coffee, Charcoal, Titanium, Flame, Peanut and Shell). The panel shall be classified for Fire Class A, as per ASTM E-84. The Acoustical Wall Panel shall be of sizes 600x600mm (Nominal) or 600x1200mm (Nominal) and shall achieve an NRC of 0.85 (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) with 50mm airgap as per ASTM C423 to be fixed to wall on a framework of wooden battens and using Wall panel Impalers (supplied by the manufacturer) or by using construction adhesives (as per the instructions laid down by the manufacturer). The fibre glass substrate shall have a recycle content of 85%. Installation:An appropriate vapour barrier (by others) shall be applied/installed on the vertical surface before the installation to properly seal against entry of any moisture. Vapour barrier (by others) shall be installed as per Manufacturer’s recommendation. Install wooden batten grid (provided by others) of section 50x50mm or as approved by the Architect on the solid wall/partition to provide level and plumb surface. The Impalers shall be fixed to the battens using self-tapping screws, 3 nos. in case of 600x600mm and 4 nos. in case of 600x1200mm. Silica based construction adhesive (by others) to be dabbed on to the projecting elements.R.A.No.160.
GROUND FLOOR Providing and fixing 25 mm diameter water meter with non-return valve including strainer, sockets/union nutand including water meter box making locking arrangement and lock.[Without chamber].
GROUND FLOOR Providing and fixing 40 mm diameter water meter with non-return valve including strainer, sockets/union nutand including water meter box making locking arrangement and lock.[Without chamber].
GROUND FLOOR Providing and fixing 80 mm diameter water meter with non-return valve including strainer, sockets/union nutand including water meter box making locking arrangement and lock.[Without chamber].
GROUND FLOOR Providing and fixing 15cm x 10cm salt glazed PVC gully trap in cement concrete 1:4:8 outside the building including cast iron grating in the sink, connecting glazed stoneware pipe, brick masonry chamber with cast iron lid and cast iron grating for the gully trap.
GROUND FLOOR Providing , constructing and fixing 450 mm dia. Inspection chamber made up of Polypropylene / polyethylene material of thickness 3.5 mm and height of 388 mm with 160 or 200 mm main inlet (s) outlet and 110 and / or 160 mm branch inlets, with 450 mm dia. Ultra shaft pipe of HDPE material having height of 460 mm, having R.C.C. cover and frame fixing in 150 mm thick in c.c.1:2:4, having crushed sand bed of 150 mm thick of size 750 mm dia. Including excavation and refilling the sides of chamber by sand crushed cushioning 150 mm thickness, connecting all required UPVC fittings with rubber lubricant etc. complete.
GROUND FLOOR S.P.TABLE :Providing and fixing in position customised " S P Table having size 3.45 X 0.90 X 0.750 meter " & Side Table 1.4 X 0.6 X 0.6 meter made to measurement as per design drawing. Carcass shall be made out of 18 mm commercial plywood Conforming IS 303:1989 on surface, All exposed edges to be finished with best quality teakwood patti of size 1/2 inch. All Inner surfaces to be finished with 1 mm thick white laminate lining &Veneer 3.5 to 4 mm thick for outer faces and 6 mm thick white corien used on top side. Adhesives used shall be low-VOC compliant as per GRIHA.Including handles 150mm, Iron hinges, slidding strip channels, magnetic ball catcher, concealed lock, nails & screw and installation shall be in true line & level complete with necessary provision for electrical switches & wiring if any. The rate shall be inclusive of all labour, material, scaffolding, transportation, including all leads, lifts at all levels and as directed by Engineer Incharge.
GROUND FLOOR TV CABINET WITH STUDY TABLE-Providing and fixing in position TV CABINET WITH STUDY TABLE size (1.82 X 0.6 X 0.75 meter)( 1.5 X 0.6X 0.750 meter ) in the Room, wooden structure as per detail drawing with 18 mm thick commercial plywood Conforming IS 303:1989 on surface Also granite top on luggage & survice table ,all the edges to be finished with best quality teakwood bidding patti of size 1/2 inch. All surfaces to be finished with Telephone Black Granite as per drawing . Adhesives used shall be low-VOC compliant. Including applying mealamine polish to all wood work, Including handles 150mm, Iron hinges, slidding strip channels, magnetic ball catcher, concealed lock, nails & screw and installation shall be in true line & level complete with necessary provision for electrical switches & wiring if any.Including all leads, lifts at all levels etc. complete and as directed by Engineer Incharge. RATE ANALYSIS NO 06.
FIRST FLOOR TV CABINET WITH STUDY TABLE-Providing and fixing in position TV CABINET WITH STUDY TABLE size (1.82 X 0.6 X 0.75 meter)( 1.5 X 0.6X 0.750 meter ) in the Room, wooden structure as per detail drawing with 18 mm thick commercial plywood Conforming IS 303:1989 on surface Also granite top on luggage & survice table ,all the edges to be finished with best quality teakwood bidding patti of size 1/2 inch. All surfaces to be finished with Telephone Black Granite as per drawing . Adhesives used shall be low-VOC compliant. Including applying mealamine polish to all wood work, Including handles 150mm, Iron hinges, slidding strip channels, magnetic ball catcher, concealed lock, nails & screw and installation shall be in true line & level complete with necessary provision for electrical switches & wiring if any.Including all leads, lifts at all levels etc. complete and as directed by Engineer Incharge. RATE ANALYSIS NO 06.
GROUND FLOOR DINNING TABLE -Providing and fixing in position U SHAPE DINNING TABLE 5.95 X 3.00 meter size in the Room, wooden structure as per detail drawing with 18 mm thick commercial plywood Conforming IS 303:1989 on surface Also granite top on luggage & survice table ,all the edges to be finished with best quality teakwood bidding patti of size 1/2 inch. All surfaces to be finished with Telephone Black Granite as per drawing . Adhesives used shall be low-VOC compliant. Including applying mealamine polish to all wood work, Including concealed lock, nails & screw and installation shall be in true line & level complete with necessary provision for electrical switches & wiring if any.Including all leads, lifts at all levels etc. complete and as directed by Engineer Incharge.
GROUND FLOOR WALDROBE-Providing and fixing in position WALDROBE size 2.40 X 2.40 X 0.60 meter in the Room, wooden structure as per detail drawing with 18 mm thick commercial plywood Conforming IS 303:1989 on surface,all the edges to be finished with best quality teakwood bidding patti of size 1/2 inch. All surfaces to be finished with 1 mm thick white mica laminate as per drawing . Adhesives used shall be low-VOC compliant. Including applying mealamine polish to all wood work, Including handles 150mm, Iron hinges, slidding strip channels, magnetic ball catcher, concealed lock, nails & screw and installation shall be in true line & level complete with necessary provision for electrical switches & wiring if any.Including all leads, lifts at all levels etc. complete and as directed by Engineer Incharge.
GROUND FLOOR WAITING AREA BENCH- Providing and fixing of size 4'L x 18'' w x 18''H , 3'' Thick of two web & single flange ,precast m20 grade cement concrete with 10 mm tmt steel, colour superfine chips, mirror polish finish ,as per drawing.etc complete..RA NO.14.
GROUND FLOOR WALL MURAL :- Supply and installation of wall mural in 20 - 25 mm Sandstone with carving depth of 2-3 mm according to specified design. Pasted on wall using UV resistant stone adhesive and necessary precautions. With water repellent PU coating on surface , as per drawing.etc complete.RA NO 15.
GROUND FLOOR FULL HEIGHT PLY PARTITION WALL-Full Height Partitions in Solid finish Providing and Fixing 80mm to 85mm thick Full height Double Skin partition up to 3 mtr height with All visible sections in Anodized / Powder coated finish. Made up of Frames and Tiles. Frame construction In combinaton of Aluminium Rails and Bottom ,Center and Top members, Connected with 2 way Round Shape Post , 3way Post , 4 way Post made up of Aluminium Extruded and Tiles in 9mm thk. Prelaminated Partical Board of on both side. With all the Joints in the partitions covered with PVC extrusions to provide better sound Proofing. Tiles to be separated 55mm from Number other to provide adequate space for drawingcables for electric, data and telephone with proper facility for fixing electrical and data switchplates. as per design and drawing SSR 2020-21 Item No. 52.56 Page No. 432.
FIRST FLOOR FULL HEIGHT PLY PARTITION WALL-Full Height Partitions in Solid finish Providing and Fixing 80mm to 85mm thick Full height Double Skin partition up to 3 mtr height with All visible sections in Anodized / Powder coated finish. Made up of Frames and Tiles. Frame construction In combinaton of Aluminium Rails and Bottom ,Center and Top members, Connected with 2 way Round Shape Post , 3way Post , 4 way Post made up of Aluminium Extruded and Tiles in 9mm thk. Prelaminated Partical Board of on both side. With all the Joints in the partitions covered with PVC extrusions to provide better sound Proofing. Tiles to be separated 55mm from Number other to provide adequate space for drawingcables for electric, data and telephone with proper facility for fixing electrical and data switchplates. as per design and drawing SSR 2020-21 Item No. 52.56 Page No. 432.
GROUND FLOOR FULL HEIGHT GLASS WALL- Full Height Partitions in Glass finishProviding and Fixing 80mm to 85mm thick Full height Double Skin partition up to 3 mtr height with All visible sections in Anodized / Powdercoated finish. Made up of Frames and Tiles. Frame construction In combinaton of Aluminium Rails and Bottom ,Center and Top members, Connected with 2 way Round Shape Post , 3way Post , 4 way Post made up of Aluminium Extruded and Tiles in 5mm thk. Non Toughened Glass on both side. With all the Joints in the partitions covered with PVC extrusions to provide better sound Proofing. Tiles to be separated 55mm from Number other to provide adequate space for drawing cables for electric, data and telephone with proper facility for fixing electrical and data switch plates. as per design and drawing.. SSR 2020-21 Item No. 52.57 Page No. 433.
FIRST FLOOR FULL HEIGHT GLASS WALL- Full Height Partitions in Glass finishProviding and Fixing 80mm to 85mm thick Full height Double Skin partition up to 3 mtr height with All visible sections in Anodized / Powdercoated finish. Made up of Frames and Tiles. Frame construction In combinaton of Aluminium Rails and Bottom ,Center and Top members, Connected with 2 way Round Shape Post , 3way Post , 4 way Post made up of Aluminium Extruded and Tiles in 5mm thk. Non Toughened Glass on both side. With all the Joints in the partitions covered with PVC extrusions to provide better sound Proofing. Tiles to be separated 55mm from Number other to provide adequate space for drawing cables for electric, data and telephone with proper facility for fixing electrical and data switch plates. as per design and drawing.. SSR 2020-21 Item No. 52.57 Page No. 433.
SECOND FLOOR FULL HEIGHT GLASS WALL- Full Height Partitions in Glass finishProviding and Fixing 80mm to 85mm thick Full height Double Skin partition up to 3 mtr height with All visible sections in Anodized / Powdercoated finish. Made up of Frames and Tiles. Frame construction In combinaton of Aluminium Rails and Bottom ,Center and Top members, Connected with 2 way Round Shape Post , 3way Post , 4 way Post made up of Aluminium Extruded and Tiles in 5mm thk. Non Toughened Glass on both side. With all the Joints in the partitions covered with PVC extrusions to provide better sound Proofing. Tiles to be separated 55mm from Number other to provide adequate space for drawing cables for electric, data and telephone with proper facility for fixing electrical and data switch plates. as per design and drawing.. SSR 2020-21 Item No. 52.57 Page No. 433.
GROUND FLOOR LOW HEIGHT STORAGE UNIT --Credestal @ 1200Lx450Lx650HT Providing & Fixing of LOW HEIGHT CREDESTAL @1200L X 450D X 650H:-To be made out of Membrane Finish (2 Openable Shutter & 3 Drawer Pedestal in between ) as per drawing.SSR 2020-21 Item No. 51.23 Page No. 344
FIRST FLOOR LOW HEIGHT STORAGE UNIT --Credestal @ 1200Lx450Lx650HT Providing & Fixing of LOW HEIGHT CREDESTAL @1200L X 450D X 650H:-To be made out of Membrane Finish (2 Openable Shutter & 3 Drawer Pedestal in between ) as per drawing.SSR 2020-21 Item No. 51.23 Page No. 344
GROUND FLOOR TABLE 03 :- Free Standing Table @ 1500Lx600Dx750HT Providing and fixing Table of Size 1500 x 600 x 750 mm. Top: made from 25 mm Commercial ply. All edges are covered by 2 mm. Thk. PVC edge bands glued by hot melt glue applied by auto edge banding machine. Legs : C Shape made from CRCA Sheet with Powder Coat finish. Modesty panel : Made from 18mm both side Commercial ply.All edges are covered by 0.8mm PVC edge bands glued by hot melt glue applied by auto edge banding machine.KEYBOARD TRAY ( WITHOUT MOUSE TRAY ) :- Metal Powder Coated - Black Color, CPU TROLLEY :Metal Powder Coated - Black Color, 3 DRAWER PEDESTAL UNIT having overall size 392L x 450D x 680Ht. mm. with central lock and key. Drawers and body are complete metal with powder coat finish, facia in 18 mm Commercial ply .SSR 2020-21 Item No. 51.26 Page No. 344
FIRST FLOOR TABLE 03 :- Free Standing Table @ 1500Lx600Dx750HT Providing and fixing Table of Size 1500 x 600 x 750 mm. Top: made from 25 mm Commercial ply. All edges are covered by 2 mm. Thk. PVC edge bands glued by hot melt glue applied by auto edge banding machine. Legs : C Shape made from CRCA Sheet with Powder Coat finish. Modesty panel : Made from 18mm both side Commercial ply.All edges are covered by 0.8mm PVC edge bands glued by hot melt glue applied by auto edge banding machine.KEYBOARD TRAY ( WITHOUT MOUSE TRAY ) :- Metal Powder Coated - Black Color, CPU TROLLEY :Metal Powder Coated - Black Color, 3 DRAWER PEDESTAL UNIT having overall size 392L x 450D x 680Ht. mm. with central lock and key. Drawers and body are complete metal with powder coat finish, facia in 18 mm Commercial ply .SSR 2020-21 Item No. 51.26 Page No. 344
GROUND FLOOR TABLE-04 -Free Standing Table @ 1200L x600Dx750HT Providing and fixing Table of Size1200 x600x 750mm.Top:made from 25 mm Prelaminated Particle board.All edges are covered by 2mm.Thk.PVC edge bands glued by hot melt glue applied by auto edge banding machine. Legs:CShape made from CRCA Sheet with PowderCoat finish.Mode sty panel:Made from 18 mm both side pre laminated particle boards. All edges are covered by 0.8mm PVC edge bands glued by hot melt glue applied by auto edge banding machine.KEYBOARD TRAY (WITHOUT MOUSE TRAY):-Metal Powder Coated-Black Color,CPU TROLLEY:-Metal Powder Coated-Black Color,3 DRAWER PEDESTAL UNIT having over all size 392L x450D x680Ht.mm.with central lock and key.Drawers and body are complete metal with powder coat finish, facia in 18 mm prelaminated particle board, SSR 2020-21 Item No. 51.28 Page No. 346.
FIRST FLOOR TABLE-04 -Free Standing Table @ 1200L x600Dx750HT Providing and fixing Table of Size1200 x600x 750mm.Top:made from 25 mm Prelaminated Particle board.All edges are covered by 2mm.Thk.PVC edge bands glued by hot melt glue applied by auto edge banding machine. Legs:CShape made from CRCA Sheet with PowderCoat finish.Mode sty panel:Made from 18 mm both side pre laminated particle boards. All edges are covered by 0.8mm PVC edge bands glued by hot melt glue applied by auto edge banding machine.KEYBOARD TRAY (WITHOUT MOUSE TRAY):-Metal Powder Coated-Black Color,CPU TROLLEY:-Metal Powder Coated-Black Color,3 DRAWER PEDESTAL UNIT having over all size 392L x450D x680Ht.mm.with central lock and key.Drawers and body are complete metal with powder coat finish, facia in 18 mm prelaminated particle board, SSR 2020-21 Item No. 51.28 Page No. 346.
SECOND FLOOR TABLE-04 -Free Standing Table @ 1200L x600Dx750HT Providing and fixing Table of Size1200 x600x 750mm.Top:made from 25 mm Prelaminated Particle board.All edges are covered by 2mm.Thk.PVC edge bands glued by hot melt glue applied by auto edge banding machine. Legs:CShape made from CRCA Sheet with PowderCoat finish.Mode sty panel:Made from 18 mm both side pre laminated particle boards. All edges are covered by 0.8mm PVC edge bands glued by hot melt glue applied by auto edge banding machine.KEYBOARD TRAY (WITHOUT MOUSE TRAY):-Metal Powder Coated-Black Color,CPU TROLLEY:-Metal Powder Coated-Black Color,3 DRAWER PEDESTAL UNIT having over all size 392L x450D x680Ht.mm.with central lock and key.Drawers and body are complete metal with powder coat finish, facia in 18 mm prelaminated particle board, SSR 2020-21 Item No. 51.28 Page No. 346.
FIRST FLOOR CARPET-Providing & Fixing in position, Carpet more than 800+ gsm, made with100% stain proof fibres of approved make along with 5mm underlay as per Architectural & Acoustical Design & Instructions & Complete in all aspects including all materials labour,finishing etc complete.SSR 2020-21 Item No. 51.13 Page No. 343.
GROUND FLOOR TEA TABLE- Tea Table 900mm X 750mm X 450mm for m.s. ante chamber Providing And Fixing Of Tea Table 900mm X750mm X450mm With 12mm Thick Colour Eitched Tempered Glass With Bevelled Drawing Made Out Of 18mm Thic Waterproofing Ply.The Outer Laces To Be Finished With High Quality 4Mm Thik Veneer Or 1Mm Thik Mica Etc.SSR 2020-21 Item No. 51.54 Page No. 355.
FIRST FLOOR TEA TABLE- Tea Table 900mm X 750mm X 450mm for m.s. ante chamber Providing And Fixing Of Tea Table 900mm X750mm X450mm With 12mm Thick Colour Eitched Tempered Glass With Bevelled Drawing Made Out Of 18mm Thic Waterproofing Ply.The Outer Laces To Be Finished With High Quality 4Mm Thik Veneer Or 1Mm Thik Mica Etc.SSR 2020-21 Item No. 51.54 Page No. 355.
GROUND FLOOR VERTICAL BLINDS-Providing and Fixing Vertical Blinds of approved Make and shade of 100mm regular fabric with powder coated aluminium channel with telting PVC chain & bottom weight plate with all necessary fixtures and fitting etc.complete.(Sample to be final by Engineer In-chargeprior execution of work)SSR 2020-21 Item No. 51.20 Page No. 344.
FIRST FLOOR VERTICAL BLINDS-Providing and Fixing Vertical Blinds of approved Make and shade of 100mm regular fabric with powder coated aluminium channel with telting PVC chain & bottom weight plate with all necessary fixtures and fitting etc.complete.(Sample to be final by Engineer In-chargeprior execution of work)SSR 2020-21 Item No. 51.20 Page No. 344.
110 mm size X 6 kG/CM2 Supply, installation, testing and commissioning of PVC Pipe of the size and Pressure rating as shown below, including the supply of all requisite Butt Join fittings etc as specified and as required complete. Make: Supreme/ Finolex
90mm x 6 Kg/Cm2 Supply, installation, testing and commissioning of PVC/ ASTM Pipe as per IS 4985 of the size and pressure rating as shown below, including the supply of all requisite molded PVC fittings etc as specified and as required complete. Make: Finolex / Supreme
75mm x 6 Kg/Cm2 Supply, installation, testing and commissioning of PVC/ ASTM Pipe as per IS 4985 of the size and pressure rating as shown below, including the supply of all requisite molded PVC fittings etc as specified and as required complete. Make: Finolex / Supreme
63mm x 6 Kg/Cm2 Supply, installation, testing and commissioning of PVC/ ASTM Pipe as per IS 4985 of the size and pressure rating as shown below, including the supply of all requisite molded PVC fittings etc as specified and as required complete. Make: Finolex / Supreme
50mm x 6 Kg/Cm2 Supply, installation, testing and commissioning of PVC/ ASTM Pipe as per IS 4985 of the size and pressure rating as shown below, including the supply of all requisite molded PVC fittings etc as specified and as required complete. Make: Finolex / Supreme
40mm x 6 Kg/Cm2 Supply, installation, testing and commissioning of PVC/ ASTM Pipe as per IS 4985 of the size and pressure rating as shown below, including the supply of all requisite molded PVC fittings etc as specified and as required complete. Make: Finolex / Supreme
Valve on 90 mm Pipe Supply, installation, testing and commissioning of Ball Valve as Control valve of suitable size as per specifications including the cost of all fittings complete.Make: Finolex /Jain /Equi
Valve on 75 mm Pipe Supply, installation, testing and commissioning of Ball Valve as Control valve of suitable size as per specifications including the cost of all fittings complete.Make: Finolex /Jain /Equi
Valve on 63 mm Pipe Supply, installation, testing and commissioning of Ball Valve as Control valve of suitable size as per specifications including the cost of all fittings complete.Make: Finolex /Jain /Equi
Valve on 50 mm Pipe Supply, installation, testing and commissioning of Ball Valve as Control valve of suitable size as per specifications including the cost of all fittings complete.Make: Finolex /Jain /Equi
Valve on 40 mm Pipe Supply, installation, testing and commissioning of Ball Valve as Control valve of suitable size as per specifications including the cost of all fittings complete.Make: Finolex /Jain /Equi
Supply, installation, testing and commissioning of 12" Rectangular Irrigation Control Valve Box etc complete Make: Cepex / Jain /Harit
Supply, installation, testing and commissioning of 10" round Irrigation Control Valve Box etc complete Make: Cepex / Jain /Harit
Supply, installation, testing and commissioning of Air Release Valves of 1" cast aluminium body for fixing on the mainline at regular intervals or at elevational changes as required with all fittings complete Make:Harit /ARI / Equi
Supply, installation, testing and commissioning of Quick coupling Valves 3/4" size of brass body for fixing on the mainline with all fittings complete Make:Harit /Equi
Supply, installation, testing and commissioning of 6" Round valve Box for housing the Quick Coupling valve & air release valve complete .Make:Cepex / Jain /Harit
Supply, installation, testing and commissioning of 40mm flush valve Make:Jain /Finloex
Sprinkler with radius of 8 m to 12m PGP Ultra with SAM , Arc & redius adjustabl technology
Sprinkler with 6-10 Mtr( PRO Spray with SAM –MP Rotator 3000 Nozzle ) Supply, installation, testing and commissioning of Rotor Sprinkler with popup height of 4" / 5" with Seal-a-matic low head drainage prevention seal and all other features including all accessories as per specification complete in various radii range as specified below. Make: Hunter
Sprinkler with 2 - 5.5Mtr ( PRO Spray with SAM – 15ANozzle ) Supply, installation, testing and commissioning of Rotor Sprinkler with popup height of 4" / 5" with Seal-a-matic low head drainage prevention seal and all other features including all accessories as per specification complete in various radii range as specified below. Make: Hunter
MP Rotator( 5-10 Mtr ) with shrub adapter with rising assembly including all fittinf MTA Complete Supply, installation, testing and commissioning of Rotor Sprinkler with popup height of 4" / 5" with Seal-a-matic low head drainage prevention seal and all other features including all accessories as per specification complete in various radii range as specified below. Make: Hunter
Spray Nozzle 15 A( 5-10 Mtr ) with shrub adapter with rising assembly including all fitting Complete Supply, installation, testing and commissioning of Rotor Sprinkler with popup height of 4" / 5" with Seal-a-matic low head drainage prevention seal and all other features including all accessories as per specification complete in various radii range as specified below. Make: Hunter
Swing Joint 3/4" Supply, installation, testing and commissioning of Rotor Sprinkler with popup height of 4" / 5" with Seal-a-matic low head drainage prevention seal and all other features including all accessories as per specification complete in various radii range as specified below. Make: Hunter
Swing Joint 1/2" Supply, installation, testing and commissioning of Rotor Sprinkler with popup height of 4" / 5" with Seal-a-matic low head drainage prevention seal and all other features including all accessories as per specification complete in various radii range as specified below. Make: Hunter
Supply, installation, testing and commissioning of inline polytube having 16mm dia & 0.4 mtr spacing of dripper with all necessary fittings like take off, gromet, connectors, tees, elbows, end caps etc as required and specified complete Make: Netafim/ Finolex
Supply, installation, testing and commissioning of Plain polytube having 16mm dia with all necessary fittings like take off, gromet, connectors, tees, elbows, end caps etc as required and specified complete Make:Netafim/ Finolex
Supply, installation, testing and commissioning of Pressure complensatting dripper 8 LPH Make:Netafim/ Finolex
Supply, installation, testing and commissioning of lateral hoding stakes Make:Jain/ Netafim
Supply, installation, testing and commissioning Pumping system with Number pump 10 LPS at 60 mtr head ( 1 W + 1S) mounted on a common skid Make: Lubi /CRI / Equiv.
Supply, installation, testing and commissioning of Control panel for 1 W + 1 S Pumping system
Supply, installation, testing and commissioning Non return valve 4 " with all fittings & accessories. Make:Normex /Kartar
Supply, installation, testing and commissioning Butterfly valve 4" with all fittings & accessories.Make:Normex /Kartar
Supply, installation, testing and commissioning of comman header assembly bypass assembly with including all fittings & accessories
Supply, installation, testing and commissioning of filtration unit with Sand Filter having capacity of 50 m3/hr. Unit along with 3" Screen filter etc complete. Make:Jain / Finolex/ Equi
BITUMINOUS CONCRETE:--Providing and laying bituminous concrete using crushed aggregate of grading 1, premixed with bituminous binder @5.40% by weight of total mix and filler, transported at site with VTS, laid over a previously prepared surface, finished to the required grade ,level, alignment, and rolling to achieve the desired density for 50mm compacted thickness with drum mix plant with SCADA, Sensor paver and Vibratory roller excluding prime/Tack coat etc. complete --Bitumen of specified grade with stone dust filler. (VG-30 bulk bitumen rates are considered to arrive at rates)
Providing and applying tack coat on the prepared surface heating by fames in Boiler andspraying bitumen set footed in bitumen boller on B.T. surface 2.5 Kilogram/10 SquareMetre.(VG-30 bulk bitumen rates are considered to arrive at rates)
Supplying on site Garden Soil/ Red Soil well sieved 90% to pass through I.S. sieve of 10mm sixe free fromstones rubbish like dried grass roots and other such materials. The soil should be fress from quarry. The colour of the soil generally be Red. The soil will be measured by measuring box(Farma). ( Item includes Royalty Charges, Transporting,loading, unloading etc) lead for 20.00km is Considered.
Providingdry/trap/granite/quartzite/gneiss rubble stonesoling 15 cm to 20 cm thick including hand packing and compacting etc. complete
Providing and fixing of single shutter GI metal sheet door, having its frame of size 100mm x 57mm x 1.20 mm, infill with M10 Grade concrete inside & shutter thickness of size 32mm (0.90 mm GI + 30.2 HC + 0.90 mm GI) including 1000 x 400 mm size 5mm float glass panel on top for ventilation purpose & required accessories ss ball bearing hinges, mortice dead lock, cylinder 70mm key & knob,D Type Pull Handle Set 300mm X 22mm , Door Stopper, Standard Arm Door Closer, Tower Bolt 8" . (Area of door upto 2.80 sqm.)
Providing and installation of tensile roofing sheets including all structural works for roofing at viewing galary. Supply & Installation of Tensile Fabric(including all necessaryhardware,SS rops etc )complete etc. (Fabric -PVDF Fabric,Make-Serge Ferari,Weight-750GSM,Tensile Strength- 0/280daN/5Cum,Tear Strength-30/28daN, Adhesion-10daN/5cm,Colour-White,Warranty-10Year)
Providing and installation of 4 seater (1200 X 900 X 750) S.S. dining table at training center at dining area. (Foldable Chair) Grey Stainless Steel SS 8 Seater Dining Table With Foldable Stools, For Commercial, Shape Rectangular, Table Top Made Of SS Sheet All Side 2 Bend With SS Stiffener. 2 nos M S Angle Fitted Inside At Middle Of The Top Duly Polished Finished Rubber Paint Coated Under the top for Deadening Sound, As per Drawing.
Providing and installation of 8 seater (2400 X 900 X 750) S.S. dining table at training center at dining area. (Foldable Chair) Grey Stainless Steel SS 8 Seater Dining Table With Foldable Stools, For Commercial, Shape Rectangular, Table Top Made Of SS Sheet All Side 2 Bend With SS Stiffener. 2 nos M S Angle Fitted Inside At Middle Of The Top Duly Polished Finished Rubber Paint Coated Under the top for Deadening Sound, As per Drawing.
Providing and installation of 2 seater (1100 X400 X750) bench with chair at training center building in class room area.Chair 2 Seater Steel Structure of MS Square Pipe withWooden Top & Storage Using French Polished to internal Surface & Also MS pipe Three Coat of Oil Paint as per approved sample.
Providing and fixing curtains with alluminium track of necessary section for windows at required locations.Fabric Name - Glory Cotton, Shade Number -3109, Curtain Cloth as per Approved Sample
Providing and fixing Mattreses for Double bed(1980 X 1800 X 615) at required locations. Thickness of mattres is 5 inch - 6 inch.2 inches of 65D latex foam, 1 inch of 55D memory foam and 5 inches of 32D HR foam
Providing and fixing heavy duty inter locking concrete Grey paving blocks of 60 mm thickness of having a strength of 300 Kilogram/Sq.cm. of approved quality and shape on a bed of crushed sand of 25 to 30 mm thick including skirting joints and cleaning etc. complete. Ground Floor
Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed material by tipper to site, laying in uniform layers with paver in sub-base /base course on well prepared surface and compacting with vibratory roller to achieve the desired density. Laying By Grader/Paver.
Proving and laying Dense Bituminous Macadam using crushed aggregates of grading 1, premixed with bituminous binder VG-30 bitumen @ 4.50 percent by weight of total mix and filler, transported to site with Vehicle Tracking System, laid over a previously prepared surface, finished to the required grade, level, alignment and rolling to achieve the desired density for 76-100 mm compacted thickness, using Batch mix type hot mix plant with SCADA, Sensor Paver, Vibratory Roller with Stone Dust filler.
Providing and applying primer coat with bitumen emulsion on prepared surface of Aggregate layer including clearing of road surface and spraying primer mixed with Nano- Technology silance in the ratio 1:100:100 (1 kg silance :100 kg SS1 Emulsion:100 liter water);the rate of 1 Liter/Sqm using mechanical means as per the direction of Engineer-in-charge. with prior approval of concerned Superitending Engineer.
Providing and laying of hot applied thermoplastic compound 2.50 milimetre thick including reflectorizing glass beads at 250 grams per square metre area, thickness of 2.50 milimetre is exclusive of surface applied glass beads as per Indian Road Congress:35. The finished surface to be level, uniform and free from streaks and holes complete.
Designing (aesthetically), and constructing RCC ground service reservoirs / RCC sumps in M-300 mix of required capacity including excavation in all types of strata, foundation concrete, container walls, bottom slab top RCC roof slab / or dome, 20 mm thick cement plaster with water proofing compound in CM 1:3 proportion to inside face of the container, including epoxy paint from inside including refilling and disposing of surplus stuff within lead of 50 M, all labour and material charges, for laying and jointing of pipe assembly for inlet, outlet washout, over flow and bypass arrangement consisting of C.I. M.S. D/F. pipes, specials and valves of given diameters, providing and fixing accessories such as M.S. ladder inside and outside, C.I. Manhole frame and cover, water top slab, B.B. masonry chamber for all valves, ventilating shafts, including giving satisfactory hydraulic test and water tightness test as per IS code and providing three coats of cement paints to all exposed surface of structure including roof surface etc. complete as per design data, criteria, obligatory requirements and detailed specifications. Anti-termite treatment shall be given for underground portion of the structure. Notes- 1)The design shall be in accordance with various relevant I.S. specification (I.S. 456/1978, I.S. 875 - 1987, I.S. 3370 -1965 or revised.) 2)Only M.S. bars grade I conforming to I.S. 432 part-I or high yield strength deformed bars conforming to I.S. 1786 or I.S. 1139 shall be used. Grade -II M.S. bars shall not be used. 3)The entire structure shall be in M-300 mix only. 4)The scope of pipe assembly work shall be upto 5 metre beyond outside face of the wall, cost of pipes valves and specials is not included in the rate but labour cost for laying and jointing is included. 5)The G.S.R. / Sump above 15 lakh litres capacity shall be in two compartment. 6)The Job includes designing the structure for uplift pressure and dewatering if required during entire execution and disposal of surplus excavated stuff within lead of 50 metres as directed by Engineer in-charge. If uplifts considered in design, then these rates shall be increased by 7.5%. 7)G.S.R. outlets shall be with bell mouth of approved pattern in bottom slab and cost of designing bell mouth is included in the rate. Sump well includes cost of suction pit required at bottom. 8)For pipe diameters upto 300 mm only CI pipes and CI specials shall be used. For pipe diameters above 300 mm, M.S. pipes and specials minimum 10 mm thick shall be used with proper anticorrosive epoxy treatment from inside and outside. 9)Cost of pump house is not included in these rates. 10)Above rates are applicable for Seismic Zones 2, 3 and 4. 11)75% part rate shall be payable for reinforcement, concrete and plastering items of all types of G.S.R.s and sumps till satisfactory hydraulic testing for water tightness test is given and till that work shall be treated as incomplete. RCC Sump Cap- 12 Lakh Litr For 10 Lakhs Litrs capacity Above 200000 Litres( factor 3.64*200000)
Supplying and erecting Supplying and erecting LED tree up light fitting of 12W including lamp with PF > 0.95 class IP 65 and above complete as per specification No K- lite Nebula Midi -4267 or equipvalent (NON-CSR) (For Landscape light along the road tree)
Supplying and erecting Supplying and erecting recess mounted 20W LED wall washers tilted 70° outwards and swivels 360° to offer best illumination on the wall with any colour with driver complete. ( Including Compatible Driver)(2-5-19) (For elevation light of Admin Building & Cyber police station)
Supplying and erecting Supplying and erecting LED Up-Down light fitting of 2x6 or 2x8W including lamp with PF > 0.95 class IP 65 and above complete as per specification No k-lite 7898 or equipvalent (NON- CSR) (For elevation of training center)
Supplying and erecting PVC trunking (PVC casing-n-capping) of size 40 mm with accessories on wall/ceiling as per specification No WG-MA/CON.
Supplying and erecting PVC box trunking of size 50x50 mm. with accessories on wall/ceiling as per specification No WG-MA/BOX
Supplying and erecting green colour earthing with 1x 1.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No WG-MA/BW
Supplying and erecting mains with 2x1.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No WG-MA/BW
Supplying and erecting green colour earthing with 1x 2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No WG-MA/BW
Supplying and erecting mains with 2x4 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No WG-MA/BW
Supplying and erecting PVC insulated PVC round sheathed 1.5 sq.mm (30 no. x 0.25 mm dia.) 3 core flexible multi stranded copper Industrial cable for voltage grade up to 1.1 kV
Supplying and erecting modular type blanking plate one module duly erected on provided plate & box.
Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 2 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.
Supplying and erecting modular pop up Box 8 module erected with provided AV/ HDMI RJ 45 6 A electrical sockets and switch on provided table.
Secondary point wiring for additional light/ bell point concealed type in min 20 mm FRLS grade PVC conduit with 1.5 sq.mm. (2+1E) FRLSH grade copper wires with required accessories as per specification No WG-PW/CW
Supplying and erecting 2 pair telephone copper cable 0.5 mm dia. with high density polyethylene insulation polyester taped Nylon Rip Cord & grey colour sheathed with FR PVC conforming to ITD specification S/WS 113C laid in provided PVC casing capping/conduit as per specification No. WG-TW
Supplying and erecting 10 pair 0.5 mm dia. jelly filled armoured telephone copper cable with poly-al laminate moisture barrier polythene sheathed G.S.Tape armoured polythene jacketed having laid in provided trench as per specification No. WG-TW
Supplying and erecting 10m HDMI cord low voltage grade minimum 4k compliant to be laid in provided conduits with male/female 19 pin HDMI connectors complete.
Supplying and erecting 20m HDMI cord low voltage grade minimum 4k compliant to be laid in provided conduits with male/female 19 pin HDMI connectors complete.
Supplying and erecting 25m HDMI cord low voltage grade minimum 4k compliant to be laid in provided conduits with male/female 19 pin HDMI connectors complete.
Supplying and erecting 15m Audio Video cord low voltage grade as per specification with required 3RCA x 3RCA connector complete.
Supplying, Erecting and Commissioning of MDF Box 150x150 pairs made from min. 1.5mm thick MS sheet as per specification no. WG-TW
Supplying, Erecting and Commissioning of 100 pairs M.S. junction box made from min. 1.5mm thick MS sheet as per specification no. WG-TW
Supplying, Erecting and Commissioning of 10 pair module for connection & disconnection of telephone cable as per specification no. WG-TW
Supplying, Erecting and Commissioning of Supplying and installing testing & commissioning of digital (hybrid) type EPABX of 6 x 32 extensions suitable upto 96 extensions complete. 1) Add Rs. 38159.00 for additional 16 extension card for digital (hybrid) type EPABX x 06 Nos ( 60679 + (38159 x 6) = 289633 =+ 5% = 304114.65 ( CSR - 1-9-26)
Supplying and installing cat-6 cable suitable for networking as per specification no. WG-COC/NC
Supplying and erecting LSZH armoured multimode optical fibre cable with 6 fibres core dia 50/125 µm (OM3) suitable upto 10 GBPS ethernet distance at 850 nm of wavelength on wall/ceiling or laid in provided pipe/trench as per specification no. WG-COC/OFC LSZH
Supplying and fixing 2 m UTP patch cord of cat 6 type in position as per specification No. WG-COC/PC
Supplying and installing 3 m fibre patch cord duplex single mode for OS1/OS2 complete.
Supplying, fixing, and configuring 1-port mini-GBIC SX MM fibre transceiver (up to 550m support 3.3V power) erected in provided rack complete.
Supplying and fixing 12 ports light guide unloaded interconnect unit rack mounted type with adapter panel for termination of optical fibre cables in provided U rack complete as per specification no. WG-NAS/LIU
Supplying and fixing 24 ports light guide unloaded interconnect unit rack mounted type with adapter panel for termination of optical fibre cables in provided U rack complete as per specification no. WG-NAS/LIU
Supplying and fixing 1 x 12 duplex adapter panel - SC complete
Supplying and fixing SC/LC type multimode duplex adapter to couple two connectors between OFC & Fibre switch/Fibre module as per specification no. WG-NAS/MMA
Supplying and fixing SC/LC type multimode pigtails (OM3) for LIU to terminate OFC in LIU as per specification No. WG-NAS/LIU2
Supplying and fixing 15U wall mount rack (Dimension-DxWxH – 500x600x767 mm) as per specification No. WG-NAS/RAK
Supplying and fixing 9U IP66 outdoor mount server rack with pole mount bracket (Dimension- DxWxH - 500x600x450 mm) as per specification No. WG-NAS/RAK
Supplying and erecting Supply and Erecting Video door Phone with 7 in build Memory Type with 50 Picture storage
Supplying and erecting Supplying Installation Testing & Commissioning of Professional Quality Imported Power Amplifier 1000 W with Built in Temperature controlled Fan Overload Protection Short circuit Protection. Voltage 24 VDC +15% / -15% Current max 30 A Performance Output power (rms/maximum) 1000W Power reduction on backup power -1 dB Frequency response 50 Hz to 20 kHz (+1/3dB 10 dB ref. rated output) Distortion <1% rated output power 1 kHz S/N (flat at max volume) >90 dB (2 Working + 1 Std. By)
Supplying and erecting Supply Installation testing andcommissioning of Desktop-Mounted 18 Cardioid Gooseneck Microphone Fully adjustable 18 cardioid gooseneck microphone designed for podium and desktop use in speech presentations conferences flexibility of removable capsules cardioid polar patterns. high sensitivity and balanced transformerless output for maximum immunity to electromagnetic hum and RF interference even over long cable runs. Wide dynamic range and frequency response for accurate sound reproduction across the audio spectrum Interchangeable cartridges provide the right polar pattern for every application Balanced transformerless output for increased immunity to noise over long cable runs Shock mount that provides over 20 dB isolation from surface vibration noise Locking flange mount for permanently securing microphone to lecterns pulpits or conference tables. Frequency Response- 50 Hz to 17 kHz Dynamic Range (Typical)- 94 dB ( 1 kW Load) Signal-to-Noise Ratio- 65.0 dB (Referenced 94 dB SPL) Maximum Input Sound Level- 123.0 dB (1 kHz 1% THD 1 kW Load) 11 to 52 VDC phantom power Output Impedance- 150 Ohms (180 Ohms Actual 1 kHz)
Supplying and erecting Supplying Installation Testing & Commissioning of Professional Quality Imported Power Amplifier 480 W with Built in Temperature controlled Fan Overload Protection Short circuit Protection. Voltage 24 VDC +15% / -15% Current max 30 A Performance Output power (rms/maximum) 480 W / 720 W Power reduction on backup power -1 dB Frequency response 50 Hz to 20 kHz (+1/3dB 10 dB ref. rated output) Distortion <1% rated output power 1 kHz S/N (flat at max volume) >90 dB (2 Working + 1 Std. By)
Supplying and erecting Supplying Installation Testing & Commissioning of Chairman Unit Priority button for chairman microphone Microphone on/off button two headphone sockets Acoustic input at the microphone- 85 dB SPL frequency Response- 400Hz to 10KHz length of the microphone with flexible stem of 488 mm in length and operating tempreture -5 °C to + 45 °C
Supplying and erecting Supply installation and commissioning of Laser Projector 5000 lumens WXGA size of effective display area- 0.76” (19.3 mm) x 3 BrightEra LCD Panel Aspect ratio 16 10 Number of pixels- 3 072 000 (1280 x 800 x 3) pixels Zoom – Ratio Approx. x 1.45 Throw ratio- 1.28 1 to 1.88 1 Lens shift Range Vertical +20% to +55% Lens shift Range Horizontal - +/- 10% Light source Type- Laser diode Filter cleaning / replacement cycle (Max.)- 20 000 H Screen size- Screen size- 40 to 300 (1.02 m to 7.62 m) Light output- 5 000 lm Contrast ratio - 500 000 1 Speaker- 16 W Display resolution- 1920 x 1200 dots Video signal input- NTSC PAL SECAM 480/60p 576/50i 720/60p 720/50p 1080/60i 1080/50i The following items are available for HDMI input only 1080/60p 1080/50p 1080/24p Keystone correction Horizontal- +/- 30 degrees Vertical- +/- 20 degrees INPUT OUTPUT -RGB / Y PB PR input connector Mini D-sub 15 pin Audio input connector Stereo mini jack INPUT B- HDMI input connector HDMI 19-pin HDCP support Audio input connector HDMI audio support INPUT C- HDMI input connector HDMI 19-pin HDCP support Audio input connector HDMI audio support INPUT D- HDBaseT interface connector RJ45 4 play (Video Audio LAN Control) VIDEO IN- Video input connector BNC Audio input connector Shared with INPUT A OUTPUT- Audio output connector Stereo mini jack LAN- RJ45 100BASE-TX USB- TYPE-A TYPE-B
Supplying and erecting Supply Installation Testing and commissioining of 22kV 400A AB Switch.
Supplying and erecting Supply Installation and commissioning of 65-inch 4K UHD 3840x2160 LED Commercial Display 65-inch 4K UHD 3840 x 2160 display with a non-glare panel delivering 300 nits of brightness connect up to two sources via HDMI or play content directly from USB with the built-in media player Built to operate reliably for up to 16 hours a day 7 days a week and includes an IP5X dust-proof rating 3HDMI USB Speakers 3-Year commercial warranty Resolution - 3840*2160 (4K UHD) Pixel Pitch(mm) - 0.372 x 0.372 Brightness(Typ.) - 3 00 nit Contrast Ratio - 4000 1 Viewing Angle(H/V) - 178/178 Response Time(G-to-G) - 8 ms(Typ.) Display Colors - 16.7M(True Display) Color Gamut - (NTSC) 72% Operation Hour - 16/7 H-Scanning Frequency -3 0 81kHZ V-Scanning Frequency - 48 75HZ
Supplying and erecting Supply Installation and commissioning of 85-86 inch 4K UHD 3840x2160 LED Commercial Display 85/86 UHD Smart Interactive Display Android and Windows can be easily switched between (PC module is required for Windows OS). Wireless screen sharing from multiple devices such as phones computers and tablets. Built-in office document and media files support. The startup apps and signal source are all customizable. Wireless and wired network connection. 5-MP camera and microphone. Operating System- Android 9.0 CPU- Quad-core A55 RAM- 4 GB ROM- 32 GB Operating System of External Module- Windows 7/8/10 Android WiFi - Dual-band 2.4 G/5 G Wi-Fi Hotspot -Dual-band 2.4 G/5 G supports enabling Hotspot and Wi-Fi at the same time Aspect Ratio - 16 9 Brightness- 350 cd/m² Resolution- 3840 (H) × 2160 (V) Viewing Angle- H 178° V 178° Lifespan- 50 000 hours Refresh Rate- 60 Hz Static Contrast- 1200 1 Dynamic Contrast- 6000 1 Light Sensor- 1 Front Ports- 1 × USB 3.0 Network Port- 1 × RJ-45 USB- 3 × USB 3.0 1 × Micro USB RS-232- 1 × RS-232 Video Input- 1 × HDMI IN Audio Output- 1 × 3.5 mm (Line OUT) port Others 1 × Touch IrDA - 1 Touch Technology Type- Infrared touch technology Response Time <10 ms. Touch Points- 20 Valid Touch - 2 mm Writing Mode- Finger + Pen Touch Resolution- 32767 × 32767 Number of Multi-user Writing Points- 2 Speaker- Power Full frequency 15 W × 2 Built-in Speaker-2 Microphone - Pick-up Distance-Far-field sound pickup 6 m–8 m (19.69 ft–26.25 ft) Number of Microphones-2 AGC- YES Echo Cancellation-YES Polar Pattern-Omnidirectional - Intelligent Noise Filtering- YES
Supplying and erecting Supplying erecting of Projector Display Power Speaker Ceiling / Wall mounting kit
Supplying and erecting Supply of imported motorised projector screen electrically operated 220 V AC 50Hz single phase. Motor mounted in side roller tube 3-wire instantly reversible type with brake. Equipped with internal thermal overload projection. Preset limit switch setting automatically stops the screen in UP and DOWN position. 3 position control switch or radio-remote control stops or reverses screen direction at any point in the operating cycle. Robust square or hexagonal case in powder coated metal casing. Wall or ceiling mounted. Size 8 x12 Ft.
Supplying and erecting Supplying & erecting 4X4 HDmi Matrix Switcher comprises of- 4x HDMI Inputs Outputs 4x HDMI Output Full HD 1080P switcher for High Quality computer graphics video signal UXGA Resolution balanced audio signal HDTV compatible with IR remote for control.
Supplying and erecting Supplying Installation Testing & Commissioning of 16 Channel Streo Mixer with phantom power mic inputs 26 inputs as standard 16 mono channels with high quality UltraMic™ pre-amps 4 stereo returns 4-bus architecture with sub-group routable to mix Built-in Lexicon dual effects processor Direct outputs for multitask recording individually switchable for prepost- fade operation Inserts on all mono channels Inserts on stereo mix bus 3-band British EQ with swept mid-band Stereo 18dB/octave 100Hz highpass filter to cut stage rumble +48V phantom power Channel Mute control 10-segment tri-colored metering Two sub-group outputs Separate mono sum output Make - Bosch Soundcraft Yamha or Equivalent
Supplying and erecting Supplying and erecting of 6 W Recess spot LED light (Tempreture -4000K Dia-145mm) and all other fixing accessories.
Supplying and erecting High performance recess mounted mirror optic family suitable for TLD lamps.This family uses the patened 3D OLC (Omni-directional Luminaire Control) lamellae helping the luminaire deliver very efficient lighting performance. 2X28 W Tube Light
Supplying and erecting Supply installation Testing commissioning 36 Watt hanging type Liner down type stand alone light fixture length 2600 and other accessories K Lite ID 1018
Supplying and erecting Supplying Installation Testing & Commissioning of Delegate Unit Microphone on/off button Two headphone sockets Acoustic Input at the microphone- 85dB SPL Frequency Response- 400Hz to 10Khz Length of the microphone from the base of the stem- 488mm Operating temperature -5 rC to +45 rC
Supplying and erecting Supplying Installation Testing & Commissioning of Horn loudspeaker 50W High efficiency driver Excellent speech reproduction Provision for inside mounting of the optional line/loudspeaker supervision board Water-and dust protected to IP 65 BS 5839?8 and EN 60849 compliant Coverage angle HxV (-6 dB 1 kHz) (°) 180 x 180 ° Coverage angle HxV (-6 dB 4 kHz) (°) 90 x 90 ° Frequency range (-10 dB) (Hz) 350 – 4000 Hz Operating temperature (°C) -25 – 55 °C Rated input voltage (V) 100 V Sensitivity (1 W 1 m 1 kHz octave) (dB) 110 dB Storage temperature (°C) -40 – 70 °C
Supplying and erecting decorative pre-wired box type fitting/batten suitable for 4 feet T8 LED tube light (excluding tube light).
Supplying and erecting Supply installation and commissioning of 2000W 2-Way bi-amped Powered Loudspeaker 2-way powered loudspeaker with 2? HF and 15? LF drivers Boasts a high-power 2 000-watt Class D amplifier and 34Hz–20kHz frequency range Advanced FIR-X tuning employs a combination of FIR filtering and corrective EQ to minimize phase distortion FOH/MAIN and MONITOR modes allow you to fine-tune your sound based on your application DSP protection safeguards your power supply power amplifiers and transducers against damage Optimized factory presets and intuitive LCD screen make operation easy Rotatable horn allows vertical or horizontal mounting 90×50° dispersion from a vertical position Constant directivity horn supplies smooth level coverage without roll-off Universal switching mode power supply offers maximum power along with stable worry-free operation Power Configuration Bi-amped Class D Channels 2 Total Power 2000W Dynamic Peak Inputs 2 x XLR-1/4? combo (line in) Outputs 2 x XLR (thru/output) USB 1 x Type A Frequency Range 34Hz-20khz (-10 dB) Crossover Frequency 1.7kHz Maximum Peak SPL 139 dB SPL 1m Horizontal Coverage Angle 90 Degrees Vertical Coverage Angle 50 Degrees Signal Processing PEQ Delay Routing 8 User Presets Enclosure Material Plywood Cabinet with Polyurea Coating
Supplying and erecting LED square / circular Max. 7W down lighter/ Panel Light having pressure die-cast aluminium housing polystyrene diffuser having system lumens output of Min. 770 Lumens min. efficacy of 110 lumen/W CRI>80 CCT upto 6500K Beam Angle of 120 deg. max. ripple of 5% THD<10% p.f. >0.95 operating range of 120-270V surge protection of 2.5 kV Life class of 50 000 Hrs. at L70B50 including driver having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty.
Supplying and erecting LED square / circular Max. 14 W down lighter/Panel Light having pressure die-cast aluminium housing polystyrene diffuser having system lumens output of Min. 1500 Lumens min. efficacy of 110 lumen/W CRI>80 CCT upto 6500K Beam Angle of 120 deg. max. ripple of 5% THD<10% p.f. >0.95 operating range of 120-270V surge protection of 2.5 kV Life class of 50 000 Hrs. at L70B50 including driver having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty.
Supplying and erecting LED square / circular Max. 18 W down lighter/ Panel Light having pressure die-cast aluminium housing polystyrene diffuser having system lumens output of Min. 2000 Lumens min. efficacy of 110 lumen/W CRI>80 CCT upto 6500K Beam Angle of 120 deg. max. ripple of 5% THD<10% p.f. >0.95 operating range of 120-270V surge protection of 2.5 kV Life class of 50 000 Hrs. at L70B50 including driver having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty.
Supplying and erecting LED square / circular Max. 25 W down lighter/ Panel Light having pressure die-cast aluminium housing polystyrene diffuser having system lumens output of Min. 2750 Lumens min. efficacy of 110 lumen/W CRI>80 CCT upto 6500K Beam Angle of 120 deg. max. ripple of 5% THD<10% p.f. >0.95 operating range of 120-270V surge protection of 2.5 kV Life class of 50 000 Hrs. at L70B50 including driver having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty.
Supplying and erecting LED Strip light 5m Length Max. 95 W IP20 class having minimum lumens output of 1600 Lumens/m min. efficacy of 90 lumen/W CRI>80 CCT upto 5000K Beam Angle of 110 deg. THD<10% p.f. >0.95 operating range of 230-270V Life class of 30 000 Hrs. at L70B50 including driver with 1 year warranty.
Supplying and erecting Supplying and erecting bulkhead fitting suitable for upto LED upto 12W fixed on wall. As per specification no. FG-IDF/BHF.(2-2-5).
Supplying and erecting integrated LED flood light fitting Max. 70W IP65 & IK07 class having pressure die-cast aluminium housing having system lumens output of Min. 8400 Lumens min. efficacy of 120 lumen/W CRI>70 CCT upto 6500K THD<10% p.f. >0.90 operating range of 140-270V inbuilt surge protection of 4 kV Life class of 50 000 Hrs. at L70B50 including driver with U shaped bracket with 3 Years warranty as per specification No FG-ODF/FLS2.
Supplying and erecting integrated LED Bollard Cylindrical/Cubical shaped 800mm 8W IP65 & IK10 class having extrusion aluminium housing with polycarbonate diffuser having system lumens output of Min. 800 Lumens min. efficacy of 100 lumen/W CRI>80 CCT upto 6500K THD<10% p.f. >0.90 operating range of 140-240V inbuilt surge protection of 2 kV Life class of 25 000 Hrs. at L50B50 including driver complete with 2 Year warranty as per specification No FG-ODF/FLS2.
Supplying and erecting integrated LED round burial light 6W IP65 & IK10 class having pressure die-cast housing having system lumens output of Min. 500 Lumens min. efficacy of 85 lumen/W CRI>80 CCT upto 6500K THD<10% p.f. >0.90 operating range of 100-240V inbuilt surge protection of 4 kV Life class of 50 000 Hrs. at L50B50 including driver salt spray tested for 500 Hrs. including making of recess of appropriate size for flushing into surface with 2 Year warranty as per specification No FG-ODF/FLS2.
Supplying and erecting Gate/garden light fitting with 200mm dia. glass bowl suitable for upto 12W LED Lamp on provided pipe as per specification No. FG-ODF/GLT
Supplying and erecting air circulator 450 mm. sweep oscillating type wall mounting 1440 RPM with speed regulator overheat protection unit totally enclosed flame proof motor suitable for 230/250 Volts single phase 50 cycles A.C. supply with one meter of 3 core lead wire and with moisture proof treatment to winding and with ‘E’ class insulation.
Supplying and erecting 20 SWG G.I sheet metal cawl rectangular / round shaped with 25 x 25x 3 (mm) angle iron frame metal mesh to avoid birds entry with necessary material suitable for exhaust fan of 300 mm as per specification no FG-FAS/MSC
Supplying and erecting seamless outside & inside smooth dry and clean copper pipe with ROHS compliant suitable for refrigerant having 22SWG thickness and inner dia/size 12mm complete.
Supplying and erecting seamless outside & inside smooth dry and clean copper pipe with ROHS compliant suitable for refrigerant having 22SWG thickness and inner dia/size 16mm complete.
Supplying, installing, testing and commissioning of single phase input & 1 phase output 1 kVA capacity online pure sine wave UPS with backup time of ....... hrs. PWM & IGBT based with 0.8 to unity output pf complete with all protections as per specification no. AP-UPS
Supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for coating and insulating on provided PC / copper pipes having 9 mm thickness and inner diameter / sizes 12 mm for solar water heater/AC system.
Supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for coating and insulating on provided PC / copper pipes having 9 mm thickness and inner diameter / sizes 16 mm for solar water heater/AC system.
Supplying, erecting and marking DPMCB 6A to 32A C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB
Supplying, erecting and marking TPMCB 40A to 63A with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB
Supplying and erecting triple pole and neutral distribution board (TPNDB) SPMCB of 4 ways/phase (12 poles) with door 1.2mm thickness surface/flush mounted IP 43 protection on iron/GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB
Supplying and erecting triple pole and neutral distribution board (TPNDB) SP/TP MCBs total 8 ways /24 poles with door 1.2mm thickness surface/flush mounted IP 43 Protection on iron/GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB
Supplying and erecting CRCA sheet metal enclosures of 1.2mm thickness with 20A 2 pin plug & earth socket and 20A 3 pin plug top with 20A/30A single pole MCB having rated short - circuit breaking capacity (Icn) 10kA complete erected on angle iron/ GI frame.
Supplying and erecting CRCA sheet metal enclosures of 1.2mm thickness with 30 A 3 pin plug & earth socket and 30A 3 pin plug top with 30A triple pole MCB having rated short - circuit breaking capacity (Icn) 10kA complete erected on angle iron / GI frame.
Supplying and erecting CRCA sheet metal one way enclosures of 1.2mm thickness suitable for DP MCB /TP MCB/FP MCB/RCCB/RCBO complete erected on angle iron/GI frame.
Supplying, installing, testing and commissioning of SF 6 Insulated 22kV 630A 16 kA/3sec 5 way outdoor extensible motorised SCADA compatible RMU internal arc tested as per electric supply company specification consisting of 2 nos. feeder with 2 LBS and 3 nos. feeder with 3 VCB compliant to IEC 62271 - 100 200 and 102 as per specification no. SW-HTS/RMU SCADA
Supplying, erecting, testing and commissioning of 22KV HT metering cubical (compact type) approved by MSEDCL / licensee fabricated with 2 mm (14 SWG) M.S. sheets with supporting angle painted with powder coating / epoxy paint of required shade copper bus bar size 25 x 6 mm heavy duty mechanical lock with counter meter for measuring no. of times the opening of meter door top side cover (CT PT cover) interlock with meter door epoxy casted 3 nos. CT having required ratio between 25/5A to 200/5A VA 10 or 15 Class 0.2S epoxy casted 3 nos. PT having ratio 22000/V3/110/V3 VA 50 Class 0.2 suitable for provided trivector meter and provision for incoming and outgoing cables complete duly tested by licensee with necessary test certificates and erected on provided plinth/ cc foundation.
Supplying, erecting & terminating FR XLPE insulated galvanised steel formed wire armoured (strip) cable 1100 V 3½ core 25 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL
Supplying, erecting & terminating FR XLPE insulated galvanised steel formed wire armoured (strip) cable 1100 V 3½ core 50 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL
Supplying, erecting & terminating FR XLPE insulated galvanised steel formed wire armoured (strip) cable 1100 V 3½ core 95 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL
Supplying, erecting & terminating FR XLPE insulated galvanised steel formed wire armoured (strip) cable 1100 V 3½ core 120 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL
Supplying, erecting & terminating FR XLPE insulated galvanised steel formed wire armoured (strip) cable 1100 V 3½ core 150 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL
Supplying, erecting & terminating FR XLPE insulated galvanised steel formed wire armoured (strip) cable 1100 V 3½ core 185 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL
Supplying, erecting & terminating FR XLPE insulated galvanised steel formed wire armoured (strip) cable 1100 V 3½core 240 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL
Supplying, erecting & terminating FR XLPE insulated galvanised steel formed wire armoured (strip) cable 1100 V 4 core 10 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL
Supplying, erecting & terminating FR XLPE insulated galvanised steel formed wire armoured (strip) cable 1100 V 2 core 4 sq mm copper conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/CU
Supplying, erecting & terminating FR XLPE insulated galvanised steel formed wire armoured (strip) cable 1100 V 3 core 2.5 sq. mm. copper conductor complete erected with glands & lugs on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU
Supplying, erecting & terminating FR XLPE insulated galvanised steel formed wire armoured (strip) cable 1100 V 4 core 4 sq. mm. copper conductor complete erected with glands & lugs on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU
Supplying, erecting & terminating XLPE insulated galvanised steel formed wire armoured (strip) cable 22 kV(E) 3 x 240 sq. mm. aluminium conductor laid in provided trench / pipe as per specification no. CB-HT
Providing and erecting Heat shrinkable outdoor termination kit for 11 kV (UE)/ 22 kV ( E ) XLPE HT cable 3x240 to 400 sq. mm. with necessary material as per specification no. CB-JT/HT
Supplying and laying (including excavation) of suitable width & depth up to 90 cm) 75 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface to required depth complete.
Supplying and erecting cast iron cable indicator plate buried along with route of cable for PVC / XLPE armoured cable as per specification No. CB-CIP
Supplying and erecting porcelain pin type insulator suitable for 22kV line with GI pin complete as per specification no. OH-INS/PN
Providing earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm complete with all materials testing & recording the results as per specification no. EA-EP
Providing pipe type earthing with 40mm. dia. G.I. pipe or 20 mm dia. G.I. Rod complete with all materials testing and recording the results as per specification no. EA-EP
Supplying and erecting copper strip of high purity required size used for earthing on wall and/or any other purpose with necessary copper clamps fixed on wall painted with bituminous paint with joints required. As per specification no. EA-EP.
Supplying and erecting GI strip of high purity required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with bituminous paint with joints required. As per specification no EA-EP.
Supplying, installing, testing and commissioning of 3 phase 22/0.433 kV 50 Hz. 630 kVA Mineral oil immersed and naturally cooled indoor type Copper wound without gas cushioning hermetically Sealed transformer delta/star connected with additional neutral brought out on load side temperature rise should not exceed 45? by thermometer in oil and 50? by the resistance method in winding at full load rating using type A winding insulation (kraft paper) with HV tapping (with off load tap changer) off load +5 to -10 in steps of 2.5% having 7 number of tap positions with standard accessories complete with test certificate with losses below 1953 Watts at 50% load 5565 Watts at 100% load as per IS 1180 (part 1) 2014 with necessary permissions of Electrical Inspector as per specification no SS- TR-SL.
Providing pair of duly tested rubber hand gloves as per IS 47705 suitable for working up to 22 kV supply complete.
Supplying and erecting G.I. pipe ‘C’ class ERW 50 mm dia with necessary fittings complete as per specification no. FF-PP
Supplying and erecting G.I. pipe ‘C’ class ERW 65 mm dia with necessary fittings complete as per specification no. FF-PP
Supplying and erecting G.I. pipe ‘C’ class ERW 75/80 mm dia with necessary fittings complete as per specification no. FF-PP
Supplying and erecting 150 mm dia cast iron double flange NRV complete with PN16 pressure rating as per specification no. FF-VL/NRV
Supplying and erecting fire brigade header ( Siamese connection )of 150 mm dia for supplying water in fire tank complete as per specification no. FF-FA/FMC
Supplying and erecting 12/15 mm dia pressure switch with provided isolation valve G.I. nipple elbow etc complete as per specification no. FF-FFA/PS
Supplying, erecting, testing and commissioning of 2 core shielded cable complete as per specification no. FF-PA/MCC
Supplying, erecting, testing and commissioning of 1.5 sq. mm speaker wire complete.
OMKAR CONSTRUCTION
Shah EPC Services & Projects Private Limited
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Download all tender documents and submit your bid