CIVIL and MECHANICAL ENGINEERING LABORATORIES ALONG WITH PHYSICS FEEE and CHEMISTRY engineering Lab equipments

Screw Gauge (0 to 25 mm )

Vernier calipers(150 mm, 6 inches. Made of stainless steel)

spherometer(Brass single disc 1 /100 mm/)

Hook’s law instruments (Shows: How the expansion of a spring changes with applied force.The apparatuses consists of a 240 mm scale on a movable stand and base )

Boyel’s law instrument (*Height of 120cm wooden scale 100 cm guarded in mm reading in both direction *The mercury reservoir is held in a calm ,sliding on metal rods)

Flywheel apparatus (CSI’ superior quality Flywheel with weights comprising of carefully machined and balanced cast iron wheel and steel spindle is supported on ball bearing in strong iron brackets Thickness 4.4 cm, Diameter :20 cm Wall type with pointer With revolution counter Set of slotted weights for flywheel complete with weight cord and hook)

Liner expansion Horizontal apparatus ( CSI' superior quality with Brass rod, stainless steel finish Complete set up • A 50 cm long expansion base with a built-in dial gauge and thermistor. Three metal tubes — brass, copper (99.5% Cu, 0.5% Te), and aluminum (98.9% Al, 0.7% Mg, 0.4% Si): 6.4 mm outside diameter. • A foam insulator to avoid heat loss at the thermistor connection point. •Thermoplastic elastometer tubing with 6.4 mm I.D.A source of steam or hot water, such as the PASCO Model TD-8556ASteam Generator.➁ A digital ohmmeter such as PASCO Model SE9589 to measure thethermistor resistance.Leads should have banana plug connectors, such as PASCO Model SE-9750 or SE-9751 Patch Cords)

Inverse square law using Photo cell (Wooden optical bench, Photocell housed with Red and black sockets, Lamp house with lamps, DC micro ammeter. • On Board Analog Moving Coil Meters • Galvanometer : 30-0-30/micro ammeter. • Selenium photocell mounted in the metal box with Metal base • Lamp holder with 60-watt bulb with Metal base Standard Accessories

Conductivity Meter( Range 0-200uS/cm 0-2mS/cm 0-1000mS/cm Resolution:0.1uS/cm Accuracy:+-1% FS 1DIGIT)

Redwood Viscometer for Lubricating Oil Type 1 flow time 20 to 2000 seconds

Photo Colorimeter (A+-0.5%,Cuvette 10mm path length,single cuvette,Measuring range 400nm to 700nm)

Muffle Furnace (Temp range 900 to 1150 degree celcius,chamber size 200*300*350 )

Electric Oven Digital PID controller

Desiccator (6inch/150mm/15cm)

8086 Microprocessor Trainer Kit with LCD display including power suppy (+5v/3A), 5V / 2.5A; +/- 12v, 100mA

8051 Microcontroller Trainer Kit With LCD display. 5V / 2.5A; +/- 12v, 100mA

Interfacing Cards - 1. Stepper motor Interface (Interface Card and One motor) 2. LCD & Keyboard 3. Multiplexed Diplay & Keypad

Embedded Boards (Arduino Boards)

ADC interface module

DAC interface module

LCD display module

Keyboard interface module

Keyboard interface module

Stepper motor controller interface module

Traffic light controller module

Temperature measurement module

Network Cable Tester

Network Interface Cards

Network HUB - 8 ports

Network Switch - 16 ports

Network Switch - 24 ports

Bridge kit for Networking

Local Area Network Trainer kit

Network configuration trainer kit

RJ45 Pass Through Tool kit

RJ45 Wire Cutter

RJ45 Cat6 Pass Through Connectors

RJ45 Cat6 Covers

RJ45 Cat5 Pass Through Connectors

RJ45 Cat5 Covers

Wire Punch Down Cutter

Crimping Tool

Portable AC voltmeter (0-250V) for laboratory

Portable AC ammeter (0-10 A) for laboratory

Portable wattmeter (0-500W) for laboratory

Connecting wires with lug

Jumper wire (male and female)

Digital Compression Testing Machine, Capacity 2000kN ( Digital Compression Testing Machine, Capacity 2000kN Meets the key specifications of IS -516 & IS 14858:- Machine Capacity:- 2000kN Least Count:- 0.1kN Minimum Clearance Between Platens :- 370mm Minimum Distance Between Side Plates:- 340mm Platen Size:- 222.0mm Piston Dia:- 222.22mm Piston Stroke:- 50mm 1. Load Frame:- a) The loading frame has a fully welded construction with a top crosshead, base and solid side walls. b) The hydraulic jack with Piston Size:- 222.2mm Dia , Piston Stroke:- 50mm is fixed on the base. e) Platens Must have two steel bearing blocks with hardened faces (Vickers hardness not less than 550), Bearing faces of the blocks shall have a minimum dimension at least 3 percent greater than the dimension of the specimen to be tested. 2. Pumping Unit:- a) Pump is suitable for operation on 220 volts, 1 phase, 50 cycles, AC supply. b) Motorised Pumping unit driven by a A.C. Electric Motor is used to operate the Hydraulic Jack shall be capable of applying the load at the specified rate, uniformly, without shock, using manual slow fast lever mounted on the unit control. c) Pumping units are supplied with double pumps, so that, as the specimen to be tested comes in contact with upper fixed platen, the faster speed pump gets cut off automatically and the slower (adjustable) speed pump becomes operative for testing the specimen at a preset desired rate normally. d) The slow- fast lever is provided to regulate the rate of loading on the specimen. Coarse controlof the rate of loading can be achieved by the to and fro movement of the lever while fine control is achieved by rotating the knob fitted on this lever. e) The load has to be manually released by means of the release valve. f) A start switch is fitted to start the machine & an stop switch is fitted on the front of the pump cover to stop the Pumping unit. 3.Digital Indicator Digital indicator with alpha numeric LCD has a back lit easy to read character set which can be seen under all lighting conditions. b) Digital Readout are controlled from the front panel which consists of a Liquid Crystal Display (LCD) with dual function keypad. 4. DAQ and Printing a) The test results can be printed during the “Sample Broken” screen display by pressing the Print key. b) Stored Test Results can be downloaded to a PC through the RS232/ USB in the ASCII format. Communication is made using Hypertext Terminal for Baud Rate of 9600. The output is with a standard 9 pin (D-Plug)/ USB.(centronic Epson compatible or emulated dot matrix printers eg. Epson LX-800,LX-300 etc. for printing the result summary).c))Data storage approx. 2000 records 5. Safety:- a) Front Door with perfex looking window Provided along with back door in loading frame. b) Piston Marked with over travel mark for operator and machine safety. c)If the load reaches 2% above the frame limit before the sample fails, the message “MACHINE MAXIMUM RANGE EXCEEDED” will be displayed on the screen. d) A dipstick is provided on the oil filler plug to measure the level of the oil in the reservoir. Maximum load should be held and retained for approximately 15 minutes, unless cancelled, using the panel mounted reset switch 6. Others; • The rate should include installation at site • Extra plates should be provided for testing standard brick sample (200 x100x100) • Provided with latest callibrabtion certificate from competent authority

Electric Laboratory Concrete Mixer(Good quality Concrete Strength Grade batch type concrete mixer Power Source: Electric Type Of The Drum Mixer: Tilting Drum Mixer Speed Of Mixing Drum: 13r/min Votage: 440 V,Phase: 3 phase,Number of cycle: 50 Automatic Grade: Automatic, Power : AC Supply Charging Capacity: 480 Liters Batch Capacity (Litre): 10ltrs Material:Cast Iron)

Electric Laboratory Concrete Mixer(Good quality Concrete Strength Grade batch type concrete mixer Power Source: Electric Type Of The Drum Mixer: Tilting Drum Mixer Speed Of Mixing Drum: 13r/min Votage: 440 V,Phase: 3 phase,Number of cycle: 50 Automatic Gr

ISI marked 150 mm Cube Moulds for Concrete(Cube Size: 150 mm as per specified IS Code Material: MS, ISI Marked No Of Parts: Three Part Size: 150mm ISI)

Concrete Needle Vibrator(Flexible shaft 2.5 m(min) Vibrating Pin 350 mm long and 40 mm dia powered by 1HP Motor, AC supply, 3Phase 440 Volt. )

Vibrating table for concrete, For Laboratory(The Vibration Table should consist of an electric motor fitted with a variable pitch pulley housed in the cabinet. The vibrations are generated by mean of off-balance masses rotating on a shaft clamped to the platform. It should carry at least 140 kg load over vibrating platform. Standard tabletop is 75cm x 75 cm minimum. Should have a special cross arm attachment over central guide to hold the moulds under preparation. The variable pulley arrangement should generate 2600 to 3600 vibrations per minute. A speed regulator device should be provided to control the vibrations. Quality (LT) switch gear should be provided for starting the unit. Standard unit should be suitable for operation of 3 Phase, 440 V AC.)

Please Enable Macros to View BoQ information