PROVN OF SEPARATE OTM ACCN FOR WOMEN MILITARY POLICE AT INF DIV PRO UNIT AND PROVN OF REWIRING OF BLDG NO 01 (ADM BLOCK) OF GARH RIF UNDER GE (EAST) FEROZEPUR CANTT

Amount

B/R work Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft and loose soil complete all as specified and directed.

Excavating over areas, n exc 1.5 m deep and getting out in soft/loose soil, complete all as specified and directed.

All as per tem item No 2 above but depth exceeding 1.5m and not exceeding 3.00m

M&L for Excavation in trenches n exc 1.5 m wide and n exc 1.5 m in depth; for foundation etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

M&L for PCC type D2, 1:4:8 (40 mm graded aggregate) as in foundations, filling and mass concrete, complete all as specified and directed.

Returing, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soill, complete all as specified and directed.

Removing excavated material as soil exc. 50 m and n.exc 250 m, depositing where directed at a level n.exc. 1.5m above the starting point, complete all as specified and directed.

Use and waste of Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finished surface of concrete complete all as specified and as directed.

M&L for RCC M-25 (Design Mix) (20 mm graded aggregate) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete etc. complete all as directed by Engr-in-Charge.

Use and waste of Formwork to sides of pillars, posts, struts, piers, columns etc rough finished surface of concrete all as complete all as specified and as directed.

M&L for RCC M-25 design mix (20 mm graded aggregate) as in column, pillars, piers, posts and struts etc.square, retactangular rough finished surface of concrete complete all as directed by Engr-in-Charge.

Use and waste of Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports,overhangs, etc. also splays between floors and beams, etc. rough finished surface of concrete complete all as specified and as directed.

M&L for RCC M-25 design mix (20 mm graded aggregate) as in lintel beams, roof beams, cantilevers etc. complete all as specified and directed.

Use and waste of form work to chajjas, including edges, rough finished surface of concrete complete all as specified and directed.

M&L for RCC M-25 design mix (20 mm graded aggregate) as in chajjas etc. complete all as directed by Engr-in-Charge.

Use and waste of Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) rough finished surface of concrete complete all as specified and directed.

M&L for Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide. complete all as specified and directed.

M&L for RCC M-25 design mix (20 mm graded aggregate) as in slab supported on walls, beams and columns in roofs etc. complete all as specified and directed.

M&L Brick work in cement mortar 1:6 using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6 metre mean radius complete all as specified and directed.

M&L Brick work in cement mortar 1:4 using sub class ‘B’ old size bricks, straight or curved on plan to any radius in half brick thick walls complete all as specified and directed.

M&L 10 mm thick screed bed or bedding layer in CM(1:4) using water proofing compound @2% by weight of cement or as per manufacturer instructions which ever is more and finished surface even and smooth smooth for laying of water proofing membrane complete all as specified and as directed. Note: WPC shall be measured and paid separately)

M&L for Polymer modified bituminous membrane with sand witched polythene film/non woven polyster reinforcement /polymeric water proofing membrane weighing minimum 3Kg/sqm ( make : IWL/STP/ HYPERPLAST ) laid after Applying bituminous primer @ 0.40 litre per Sqm over plastered surfaces of roof including parapet surfaces. (i.e roof slab cleaned throughly to remove all loose particle dust/dirt particle ) membrane shall be laid over entire roof surface and on verticle surface up to grooves ( or as per manufacturers recommendation) with over laps of 100mm The over lap shall be sealed by flames or as per manufacturer instruction.Hot blown bitumen grade 85/25 @1.2kg/Sqm applied over the membrane should be compatible with membrane all as recommendation manufacturers and all as specified and directed.

M&L for prepration of roof surface and applying two coat of solar reflective bituminous aluminium paint @0.10 Kg/Sqm over bituminious membrane complete all as specified and directed by Engr-in-Charge.

M&L for treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed by Engr-in-Charge.

M&L for treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the substructure in contact with backfill to be measured) complete all as specified and directed.

M&L for treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed.

M&L for treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

S&F Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia,complete all as specified and directed.

S & F mild steel TMT bars 6mm to 8mm dia and over cut to length, bent to shape required including cranking, bending spirally or hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc. complete all as specified and directed.

All as per item No 29 above but 5mm dia and over upto and incl 10mm dia in stirupps,spacers and binders etc complete all as specified and as directed.

M&L for plastering 15mm thick in cm 1:4 on fair faces of brick or concrete,using water proofing compound (where ever required) @3% by weight of cement or as per manufacturer instructions which ever is more surfaces finished even and fair complete all as specified and as directed. Note: WPC shall be measured and paid separately)

M&L for plastering 10mm thick in cm 1:6 on fair faces of brick or concrete,surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L for plastering 5mm thick in CM(1:3) to ceiling on concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

Supply only integral water proofing compound conforming IS 2645-1975 of approved make complete all as specified and as directed.

M&L Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats on new work complete all as specified.

M&L Preparation of newly plastered surfaces of walls etc, and applying three coats of white wash complete all as specified and as directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm over new surfaces complete all as specified and as directed.

S & F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S & F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

M & L Cement concrete (1:3:6), type C-1 using 20mm graded stone aggregate as in bed blocks of hold fasts, coping etc including necessary form work complete all as specified.

S & F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately). Make- RAJSHREE, SINTEX, ECOCELL

S&F Providing 30mm thick FACTORY MADE WIRE MESH SOLID WPC DOOR SHUTTER consisting of Density 650 Kg /Cbm Manufactured by an ISO-9001-2015 certified Company , Door to be panelled with SS mosquito Mesh and XTN aluminium Mesh for additional strength and safety purpose. (confirming as per IS:4020). The door should be water proof, termite proof, fire retardant and having screw holding capacity. Door to be fixed to frame with 3 nos. M.S powder coated butt hinges size 100mm*25mm*2mm and 32mm long steel screws drilled suitable to pass through both the walls of the M.S tube.Other hardwares should be fixed with 19*6mm size steel screws etc. Complete as per direction of Engineer-in -charge, manufacturer's specification & drawings. Make- RAJSHREE, SINTEX, ECOCELL

S&F aluminium anodised handles 150 mm long fixed to doors complete all as specified and as directed.

S&F aluminium anodised tower bolts 200 mm long fixed to windows complete all as specified and as directed.

S & F stainless steel butt hinges, 125 mm long, fixed with galvanised mild steel hinge pin complete all as specified and as directed.

S & F Aluminium alloy, anodised, sliding door bolt 300 mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

S & F floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor overall length of cover plate 140 mm complete all as specified.complete all as specified and as directed.

S&F 300 mm Mild steel helical door spring including roller and roller plate complete all as specified and as directed.

M & L Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and as directed.

M & L solid panel PVC door shutters 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement and fixed in the frame at site complete all as specified in clause 8 B.2.1 of MES schedule Part-II (2004). complete all as specified and as directed.

S & F factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead /double glazing bead of appropriate dimension. comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made

S & F factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Glass shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

S & F Plain sheet glass 5.5 mm thick, ordinary quality and glazing, fixed (supplied alongwith shutters), in squares exc 0.50 Sqm complete all as specified

S & F Figured glass, 5 mm thick, pin headed type and glazing in squares not exceeding 0.50 square metre each pane complete all as specified.

S & F stainless steel Wire cloth, 0.56mm nominal dia of wire and average width of aperture not more than 1.18 mm and fixed with tinned tacks or galvanized wire staples complete all as specified.

S & F PTMT tower bolts, 150 mm long and fixed with steel screws complete all as specified.

S & F PTMT butt hinge, 100mm long, fixed with steel screws with brass/bronze hinge pin complete all as specified.

S & F PTMT handle 125mm long fixed with steel screws complete all as specified.

M&L machine cut kota stone flooring 18-20 mm thick over & including 20mm thick screed bed in cement mortar 1:6, laid jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete all as specified and as directed.

M&L machine cut kota stone 16-18 mm thick as in risers of steps, skirting, dado etc over & including 15mm thick rendering in CM 1:6, jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing & polishing complete all as specified and as directed.

S&F Galvanised steel water tubes 15 mm bore medium grade, with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and as directed.

S&F Galvanised steel water tubes 20 mm bore medium grade, with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and as directed.

S&F 1000 litres capacity rotational moulded, triple layer polythene water storage tanks (cylindrical vertical with closed top) hoisting and fixed in position on roofs including fittings complete all as specified and as directed.

S&F 20mm bore brass ball valve high pressure with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed, complete all as specified and as directed.

S&F PVC Connection pipe (LDPE) of pressure rating 6 Kg per Sq.cm, 450mm long, heavy duty with two sets of brass nuts & washers (one at each end)etc suitable for 15mm bore of pipe complete all as specified and as directed.

S&F Soap dish of PTMT fixed to wall with steel screws and PVC rawl plug complete all as specified and as directed.

S&F Vitreous china white squatting pan orrissa pattern of size 580mm x 440 mm with integral foot rests including necessary lime concrete and 110 mm bore PVC (SWR) 'P’ trap with 550 to 600 mm long neck for connecting WC to branch piece with cement joints, complete all as specified.

S&F Vitreous china wash down water closet pan ( pedestal pattern including P or S trap), white/ coloured including seat & cover, flush pipe,health faucet connection to drain and to flushing pipe, anti-syphonage pipe, etc. complete all as specified.

S&F PVC low level flushing cistern (white) of 10 liters capacity with inlet ball float valve, PVC flush pipe and necessary fixing arrangements and connecting to water pipe and WC etc complete all as specified and as directed.

S&F fancy type viterous china under counter wash hand basin oval shaped of size 190x550x430 of Make Jaquor cat No FLS-WHT-0401 or equivalent including waste pipe etc to be fixed in Granite by cutting in required shape complete all as specified and as directed.

S&F Mild steel curtain rod powder coated with fixing side brackets, end cups, rings @ 10 Nos per RM and fixed with PVC rawl plugs & steel screws complete all as specified and as directed.

S&F 110mm bore PVC (SWR) pipe of pressure not less than 4 Kg/Sqcm in single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F 110mm bore, PVC (SWR) bends any radius complete all as specified.

S&F 110mm bore, PVC (SWR) branch piece, single (single T) equal or unequal with access door complete all as specified.

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed.

S&F 75mm bore, PVC (SWR) bends any radius complete all as specified.

S&F cast iron floor Trap 100mm dia with gratting with grating including jointing with solvent cement complete all as specified.

S&F 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified

S&F for Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and as directed.

S&F bib taps 15mm bore, cast copper alloy with crutch or butterfly handle, screwed down screwed for iron pipe or for brass ferrule fancy type chromimium plated complete all as specified and as directed.

S&F for CP pillar cock central hole basin mixer without popup waste system with 450 mm long braided hoses hot and cold water screwed down for pipe and fixed bore of pipe 15mm Make of Jaquar cat No 23167B/Ess Ess or equivalent complete all as specified and directed

S&F 15mm stop valve/ Angle cock cast copper alloy with crutch or butterflty handle, screwed down for iron pipe or brass ferrule fancy type chromium plated concealed type with long shank and cup complete all as specified.

S&F towel rail 600mm long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (Min wt 190 gms) complete all as specified and as directed.

S&F 125mm dia CP brass shower rose with swivel joints, any colour including shower arm 15mm dia, 195mm long with bend of 45 degree with flange of CP brass as in repair complete all as specified.

M&L for Moorum/red bajri filling in floors or pavings, laid in layeres n.exc. 15 cm thick, spread, levelled and rammed including watering, complete all as directed by Engr-in- Charge.

M&L for Hard core , using broken bricks of guage n.exc. 63mm, deposited, spread and levelled in layeres n.exc. 15 cm thick, watered and rammed to a true surface, as in below sub base, plinth protection and ramp, complete all as directed by Engr-in- Charge.

M&L for PCC 100 mm thick, type D-2, 1:4:8 (40mm graded aggregate) as in sub-base including necessary form work complete all as specified and as directed.

M & L for non skid coloured ceramic tiles of 7 to 8 mm thick , area of each tile exceeding 0.11 sq m but not exceeding 0.18Sq m in floors set and jointed in neat cement slurry and pointed in white cement mixed with colour pigment to match over and including screed layer of 15 mm thick in CM 1:6 complete all as specified and as directed.

M&L for Glazed ceramic tiles, coloured (light shade with dark shade boder as approved), of size 300X200/300x450 of 7mm thick on vertical surfaces such as in skirting/dado etc set and jointed in cement slurry and pointed in white cement with pigment to match the colour of tiles, laid over and including 10mm thick backing coat in cement mortar (1:4) complete all as specified and directed.

M&L for Providing precast cement concrete louvres and jallies, 25mm thick Set in cement mortar (1:3) type B-0 (1:2:4) 12.5mm graded stone aggregate (measured solid), including all mould- ings but excluding frame (Note:- Pre cast frame shall be measured & paid separately.)

M&L 50mm thick PCC(1:2:4) type B1 (20mm graded stone aggregate as in plinth protection laid in alternative panels finished even and smooth without using extra cement complete all as specified and as directed.

Removing of excavated materials (soil) n.exc 50m and deposited where directed at a level n exc 1.5m above the starting point.

M&L 50 mm thick PCC, type B-1, 1:2:4 (20mm graded aggregate) as in flooring , surface finished even and smooth without using extra cement complete all as specified and as directed.

M & L coloured chequered cement concrete tiles of size 30cm x 30cm x 20-22mm thick jointed and pointed in neat cement slurry with grey cement and pigment.

M & L 15 mm thick screed bed or bedding layer of mortor in CM (1:4) for laying floor finishes

M & L 150 mm dia Salt Glazed stone ware drain pipes laid in trenches and jointed complete all as specified and as directed.

M & L for PCC 1:3:6 type C2 (using 40 mm graded stone aggregate) in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of 150 mm bore complete all as specified and as directed.

M&L Reinforced Precast cement concrete 1:2:4, type B1 (Using 20 mm graded granite stone aggregate) in landings, cover slabs (for manholes etc.) shelves and similar articles with plain faces and set in cement mortar 1:6 complete all as specified and as directed. Note: Reinforcement will be measured and paid seperately.

M&L for cement concrete type B-2, 1:2:4 (using 40 mm graded stone aggregate) in surface channels and drains complete all as specified and as directed.

M&L for rendering 15 mm thick in CM 1:4 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete complete all as specified and as directed.

M&L for cutting into existing manhole for connecting new drains of internal dia 150mm , making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete(1:2;4), smooth finished and reforming nching as required complete all as specified and as directed.

E/M WORKS M&L for point wiring with 1.5 Sqmm (nominal area), PVC insulated,FRLS multistranded, single core unsheathed, copper conductor cables drawn through and including PVC conduit with all accessories concealled in wall and fixed to ceiling etc. with and including 1.5 Sqmm (nominal area) PVC insulated, unsheathed,multi stranded, single core, copper cable green in colour as earth continuity wire connecting to common earth dolly including sunken boxes of suitable size with 3 mm thick hylam sheet top cover fixed with suitable size of brass screws for mounting switches, sockets, regulators etc complete for one light/fan/bell point controlled by one ,one way switch all as specified and directed. (a) One light point / fan point/ Exhaust point controlled by one single pole one way switch. Note: wiring shall be done in colour coding

All as per item No. 103 here-in-before but One 3 pin socket outlet 5 amps independent board with cable 1.5 Sqmm size

All as per item No. 103 here-in-before but One 3 pin socket outlet 5 amps on the same board with other switches with cable 1.5 Sqmm size

All as per item No. 103 here-in-before but one 15 Amps socket outlet point controlled by one single pole switch one way and wiring with 2.5 Sqmm PVC insulated,stranded,unsheated copper conductor on independednt board with continuous earth wire of size 2.5 Sqmm green colours PVC insulated, unsheathed,stranded copper conductor cable.

All as per item No. 103 here-in-before but one 15 Amps socket outlet point controlled by one single pole switch one way and wiring with 4.0 Sqmm PVC insulated,stranded,unsheated copper conductor on independednt board with continuous earth wire of size 4.0 Sqmm green colours PVC insulated, unsheathed,stranded copper conductor cable.

S & F Modular Switch one way 6 A, 1 module complete all as per specified and directed.

S & F Modular Switch one way 16 A, 1 module complete all as per specified and directed.

S & F Modular Socket,6A - 2/3 pin combined 2 module complete all as per specified and directed.

S & F Modular Socket,6A16A - 2/3 pin combined 2 module complete all asper specified and directed.

S & F Modular white cover plate including GI box inner, 3 module complete all as per specified & directed.

S & F Modular white cover plate including GI box inner, 4 modulecomplete all as per specified & directed. Make : Precision/Anchor/Havells/Legrand

S & F Modular white cover plate including GI box inner, 8 module complete all as per specified &directed. Make : Precision/Anchor/Havells/Legrand

S & F Modular step type regulator,120 W - 2 module complete all as per specified and directed.

S&F Modular Bell push 6A 1 module single pole one way, white in colour all as specified and directed.

S&F Ceiling rose surface type, 240 volts, 50 Hz, 6A, Pilot 3 plate, white in colour, bakelite 65 x 50mm, 3 terminals duly ISI marked complete all as specified and directed.

S&F rotary Stepped type electronic fan regulator for ceiling fan 1200/1400mm size, 240 volts, 6 Amps, 100W, white in colour, duly ISI marked complete all as specified.

S&F Lamp angle holder (Plastic Ring), 240 volts, 50 Hz, 6A, white in colour, duly ISI marked complete all as specified and directed.

S&F LED bulb of 9 watt, B22, 6500K all as specified and directed.

S&F 20W, 6500 K, 4 feet LED Square tube light fitting, energy efficient fixed to wall/ ceiling etc complete.

Supply and fixing of LED Bright Lyts 6W Picture/Mirror/Spot/Bathroom/Display/Wall Flexible Neck Light (White) 2 ft adjustable type enegy saving curve type complete all as specified and directed.

Supply and fixing Study lamp / table lamp with quality CFL/LED light bulb and material with conical shade over writing shelf with standard perfect height complete all as specified and directed.

S&F LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/ 66 protection complete.

Supply and fix Plastic body fresh air fan 250mm size single phase, with fixing in the wall including provision of PVC flexible copper cable of size 23/00.0076 three core from ceiling rose to exhaust fan max 1.5 mtr for giving connection complete all as specified. including making of hole/opening in wall complete all as specified and directed by Engr in charge.

S&F ceiling fan 1200mm sweep, AC single phase 230 Volts 50Hz, at Bldgs upto 5 mtrs height, including provision of flexible cable 3 core copper conductor of size 23/0.0076 of suitable length from ceiling rose to ceiling fan upto 1.5 mtr for giving connection and all hanging arrangement i.e. standard down rod, hanging clamp, with rubber real nuts bolts, spring washers and locking of splite pin, plastic canopy with screw compete without fan regulator and marking of MES nos with black synthetic enameled paint all as specified and as directed.

M&L Cutting holes, grouting nuts for fixing of Exhaust fans making good the distributed surface, complete all as specified and directed.

S&F Factory made three phase and neutral Sheet Steel made out of CRCA 1.2 mm thick, powder coated double door vertical distribution board 4 way, dust and vermin proof, fitted with two cover, one screwed cover for incoming and outgoing MCBs and the second for protection of MCBs fitted with colour bus bar of capacity 200 Amps, neutral link, earth bar and din rail suitable for use on 240/415V, 50Hz supply, VTPN DB, partly immersed in wall, including of MCCB 4 pole adjustable thermal & fixed magnetic type 100 Amps, 50Hz, 415 Volts with rupturing capacity 16 KA and making good distrubbed surfaces with matching colour, complete all as specified.

S&F Factory made sheet metal enclosures double door type made out of CRCA 1.2 mm thick M.S sheet,powder coated, SPN DB with 200 Amps rated bus bar, 8 way, IP-42 protection surface mounting, 240 volts, dust and vermin proof, suitable for incorporation of MCBs duly cocealled in wall, factory made, including making good distrubbed surfaces with matching colour.

S&F MCB SPN, 40 Amps, 240 volts, "B" series, 10KA duly ISI marked, complete all as specified.

S&F MCB SP, 6A-32 Amps, 240 volts, "B" series, 10KA duly ISI marked, complete all as specified.

M & L for sub main wiring with 1100 volt grade two single core FRLS Wire PVC insulated and unsheathed cable with stranded copper conductor 6 sqmm drawn into and including electrical grade PVC conduit not less than 25 mm dia with IS 9537 (Part-III) 1983 mark, or relevant ISI mark with all accessories fixed concealed including chase cutting in brick/ stone masonry for fixing conduit and making good the disturb surfaces of wall as per existing including 6 sqmm multi - stranded copper conductor as earth wire in green colour complete all as specified and directed. Including taking down old unserviceable sub main wiring . NOTE Two runs of 6 sqmm PVC FRLS multi stranded copper cable wire and One run of 6 sqmm PVC FRLS multi stranded copper cable earth wire and One run (01 meter) PVC conduit of suitable size ISI mark will be measured and one unit length.

M&L Earthing complete with galvanized steel plate elecrode of size 60 cm x 60cm x 6.0 mm thick burried directly in ground vertically to a depth not less than 2.5 mtr below the ground level with top edge of earth plate at a depth not less than 1.5 mtr below ground level. Earth plate surrounded by 15mm thick packed alternative layers of charcoal dust and comman salt, earth lead GI wire of 4mm dia (8 SWG) by means of bolts, nuts, check nuts and washers of galvanised iron with thimbles. The other end of GI earth wire is connected to main switch board and protected by light grade GI pipe of 15 mm bore. provision of 20mm bore light grade GI pipe for watering including GI funnel and wire mesh. Pipe shallbe provided vertically upto top level of earth pit and then taken horrizontally to the earth pit. Cement concrete chamber of PCC (1:3:6) type C-2 using 40 mm graded stone aggregate.The chamber shall be constructed one metre away from edge of earth pit. 50 mm thick pre cast cover of cement conrete (1:2:4) type B-1 using 20 mm graded stone aggregate and MS angle iron 50 x 50 x 6 mm frame including two coats of painting over a red oxide to exposed steel surfaces. excavation in soft/ loose soil, returning filling and removal of surplus soil to a distance of 50 mm as directed and shown in Electrical Plate No- 3 of SSR Part-1 (2009) .

Supplying, laying, jointing and testing XLPE insulated, armoured, electric cables (heavy duty) with aluminium conductor, 1100 volts, grade cross sectional area 35 sqmm 3.5 core confirming to IS:7098-1985 laid in trenches, in floor, in duct, through pipes or along the pole complete all as specified. (Note ;- Excavation & earth work, brick prtoction measured and paid separately)

M&L Dry and clean fine sand for cable cushioning to underground cable protection, complete all as specified. Note- Punned down thickness shall be measured.

S&F Cover to underground cable with one layer of bricks using sub class ‘B’ bricks (old size) laid flat across the cable complete all as specified.

S&F Mild steel galvanised pipe, light grade, 40 mm nominal bore for passing of cable, fixed to poles/walls, laid under floor/road crossings, complete with and including clamps socket & elbow etc complete all as specified.

Supply and laying GI tubing medium grade galvanised of size 25mm bore including all fittings and short pieces laid in trenches complete all as directed by Engineer-in-Charge.

Supply and laying GI tubing medium grade galvanised of size 20mm bore including all fittings and short pieces laid in trenches complete all as directed by Engineer-in-Charge.

Supply and fix Gun-metal, globe or gate valves of 25 mm bore dia with iron wheel head, screwed both ends for iron pipe and fixed

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc.

Supply and fixing PVC connection 15mm size with brass nuts of length 450mm for Hot/ Cold water supply complete all as specified and directed.

Supply and fixing stop valves, 15mm bore cast copper alloy, screwed down, high pressure, fancy type, chromium plated with long shank and (concealed type) with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

Taking down carefully existig copper / alumn point wiring for light / fan / bell / socket 5/15 Amp points complete with fitting and fixtures such as switches, sockets, c/ rosess, holders and bracket fittings with battens / conduits / wires,T/L fittings and making good the disturbed surfaces of walls and roofs etc.and to match with existing colour complete all as specified and directed.

Taking down carefully unserviceable main switches and distribution boards with fuses/ MCB's (single phase or three phase) of any capacity all as specified and directed.

Taking down carefully old unserviceable sub main wiring including meters and making good disturbed surfaces and matching with existing complete all as directed and specified

M&L Point wiring complete with 1100 volts grade PVC FRLS insulated unsheathed cable of copper conductor, multi stranded of size 1.5 Sqmm, single core, drawn through existing conduit, accessories and existing sunken boxes, including bakelite sheets and various sizes hylam sheets for mounting switch/ sockets, fan regulators etc complete with and including continuous earth wire of size 1.5 Sqmm, single core, PVC FRLS copper conductor, insulated, unsheathed, stranded (Green colour) connected to common earth dolly complete all as specified for following :- (a) One light/ fan/ bell/ Bldg security light point controlled by one single pole one way switch. (Note:- wiring shall be done in colour coding)

All as per Item No. 147 here in before but for One 3 pin, 5 Amp, socket outlet on the independet board complete all as specified and directed.

All as per Item No. 147 here in before but for One 3 pin, 5 Amp, socket outlet point on the same board complete all as specified and directed.

S&F 5/6 amps, single pole, one way switch urea back piece (IP20), 240V, 50Hz, white in colour, duly ISI marked complete all as specified and directed.

S&F Switch piano flush type 15/16 amps, single pole one way, white in colour, duly ISI marked complete all as specified and directed.

S&F 5/6 Amps Socket 2 in 1, Urea backpiece (IP20), white in colour, duly ISI marked complete all as specified and directed.

S&F Socket outlet, UNI, 2 in one 10 Amps & 20 Amps, white in colour, duly ISI marked complete all as specified and directed.

S&F batten holder (with metal ring), 240 volts, 50 Hz, 6A, white in colour, duly ISI marked complete all as specified and directed.

Supply and fixing LED light fitting 1 x 20 Watt, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

S&F MCB SPN, 40A - 63Amps, 240 volts, "C" series, 10KA duly ISI marked, in MCB DB, complete with connection testing and commissioning all as specified.

Supply and fixing in repair LED ceiling light luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with highefficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.

Supply and fixing High flow 400mm 60 watt min 1350 RPM wall mounting fan including connections complete all as specified and directed.

Fixing or hanging only ceiling fans height upto 3mtr to 5 mtrs ceiling height of bldg including three core FR PVC Insulated & overall round sheathed flexible with PVC, colour of cores are Red, Black & Yellow/ Green is for earthing. Sheath colour is Black of cable size 23/0.0076 complete all as specified. Note : Ceiling fans obtained/ taking down from item Sr No.144 above shall be reused.

Supply and Fixing metal enclosure (plug & socket type DB) complete including Single pole & Neutral Sheet metal enclosure with a two pin and earth plug Top and socket complete with one Double pole MCB of 32Amps all as specified and directed.

M&L Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc as required 4 mm dia galvanised iron or steel wire.

S&F as in repairs XLPE insulated, armoured,1100 volts grade, heavy duty cable of size 50 Sqmm nominal cross section, 4 core, flat or circular, PVC FRLS insulated aluminium conductor, served with inner sheathing of galvanized steel wire or tape and over-all PVC FRLS sheathed in service connections, laid in trenches, duct, through pipe, in floor, on pole including jointing and testing, complete all as specified .(Note ;- Excavation & earth work, brick prtoction measured and paid separately)

S&F Mild steel galvanised pipe, light grade, 50 mm nominal bore for passing of cable, fixed to poles/walls, laid under floor/road crossings, complete with and including clamps socket & elbow etc complete all as specified.

HARBHAJAN SINGH KHARBANDA

M/s Sarup Singh