Spl repair to building No T-43C (FPO Bld) of 402(I) Arty Bde camp at Nurla Mil stn under AGE (I) Nimu

Amount

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, roof coverings & wall.

S&F 0.63mm thick Galvanised, corrugated mild steel sheeting with two corrugations side lap,fixed with 'L' type or 'J' type or cranked hook bolts in lieu of screws and washers, in roofs, walls etc. with grade of zinc coating 275..complete and all as specified and directed byEngr-in-charge.

S&F 0.63mm thick Plain, Galvanised, mild steel sheeting in ridges, hips, valley gutters straight flashings and etc (length and girth as fixed) with grade of zinc coating 275.complete all as specified and directed by Engr-in-charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for.

S&F Steel work Tubular truss/ member incl special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1998 grade St 240.including all welding and fittings complete all as specified and directed by Engr-in-charge.

S&F plate (plain /chequered) channels,square cut or notched (ordinary and countersunk) forming holes, without any attachment Fe 410-W (Gde - E - 250) Quality 'A'.all as specified and directed by Engr-in-charge.

M&L applying two coats of synthetic enamel painting to new surfaces steel based over a coat of red oxide primer exc. 10 cm width/girth including preparation of surfaces including filling with filler where reqd all as specified and directed by Engr-in-charge.

M&L applying two coats of synthetic enamel painting to old surfaces steel based exc. 10 cm width/girth including preparation of surfaces including filling with filler where reqd all as specified and directed by Engr-in-charge.

Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing), removing and rubbish off the premises deposited in low laying area all as specified and directed by Engr-in-charge.

S&F Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick sreed bedding layer in CM 1:4 and all as specified and directed by Engr-in-charge.

S&F glazed coloured ceramic tiles as in vertical surface Size 350x250x7mm/450x350x7mm /300x200x7 mm thick such as skirting, dado, etc set and jointed in neat cement slurry and pointed in White or coloured cement to match the shade of tiles incl 10mm thick plastering in CM 1:3 all as specified and directed by Engr-in-charge.

Demolition of Concrete in ground floors and pavings n exc 15cm thickness un-reinforced (below or above ground level).

M&L for 100mm thick Cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregate) as in sub-base in floor finishes all as specified and directed by Engr-in-charge.

M&L Chequered cement concrete tiles 30cm x 30cm x 25 mm thick with grey cement and red colour pigment set, jointed and pointed with grey cement in neat cement slurry incl 20mm thick screed in cement mortar (1:4) over PCC sub base all as specified and directed by Engr-in-charge.

M&L 75mm thickness PCC 1:3:6 type C-2 as in plinth protection and paving, all as specified and directed by Engr-in-charge.

Taking down Chowkhats or frames exc 1.5 Sqm but not exc. 4 sq. m each (without taking off shutters from the frames).

Taking down Chowkhats or frames n.exc 1.5 Sqm (without taking off shutters from the frames).

S & F in repair anoidised Aluminium powder coating frame for door, window, vendilater with one or more rebates including joining cleat for fixing etc. all as directed by Engineer-in-charge.

S & F anoidised Aluminium (powder coating thickness not less than 50 micron) door shutters aluminium sction frame work for inserting toughen glass/laminated board, al section weighting 0.5kg/m including necessary joining cleats,glzing clips,rubber paking anodised aluminium snap beading screws and handles 2 nos in each door,hinges, sliding door bolt, necessary locking arragement of etc all as directed by Engineer-in-charge.

S & F in repair anoidised Aluminium (powder coating thickness not less than 50 micron) frame work for inserting toughen glass or laminated bourd /window/ventilator shutters fixed type/side hung type with out sash bar al section/sliding type weighting 0.5kg/m including necessary joining cleats, glzing clips, rubber paking anodised aluminium snap beading,screws,anodised aluminiumfittings such as peg stays150mm long (1 nos), hinges type b-21 100mm long (2 nos) suitable handle (1 nos) including aluminium grill etc all as directed by Engineer-in-charge.

S & F in repair anoidised Aluminium (powder coating thickness not less than 50 micron) frame work for inserting toughen glass or laminated bourd for partition wall fixed type with out sash bar al section weighting 0.5kg/m including necessary joining cleats,glzing clips, rubber paking anodised aluminium snap beading, screws etc all as directed by Engineer-in-charge.

S & F 6mm thk Toughened glass, fixed in aluminium/woden frame work with nesserry arragement and fixed in repair all as specified and directed by Engr-in-charge.

S & F 3mm ACP sheet, fixed in aluminium/woden frame work with nesserry arragement and fixed in repair all as specified and directed by Engr-in-charge.

S&F Aluminium die cast body door closer hydraulically designation No 3 universal type suitable for door shutter of 851 to 1000mm in width and weight 61 to 80 kg. all as specified and directed by Engr-in-charge.

Dismantling timber scantling 40 sqcm and over in section, in any position in unframed work as in rafter, purlins etc.

M&L second class hard wood in clean sawn timber fixed in scantlings as in purlins, rafters etc

Dismantling wall and ceiling boards (fibre,pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness including cover fillets.

S&F 9mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with nails to timber frame work as in walls all as specified and directed by Engr-in crage.

S&F 9mm thick Prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination , fixed with screws to timber frame work as in walls all as specified and directed by Engr-in crage.

S&F 9mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with nails to timber frame work as in Ceilling all as specified and directed by Engr-in-charge.

Dismantling timber scantling as in fillets, rails, posts, rafters, purlins, etc. under 40 sqcm in section in any position as in unframed work all as specified and directed by Engr-in-charge.

M & L Plain fillets. exc. 13 and n.exc 25 Sqcm as in square, rectangular or triangular in section, clean sawn, secured with nails or brads.all as specified and directed by Engr-in-charge.

All as per item No 32 here in before but exc 3 & n.exc 6 Sqcm in bullnosed, splayed, chamfered or rounded on one or both edges or face as in beading all as specified and directed by Engr-in-charge.

Demolition in precast cement concrete walling built in cement mortor including all quoins, arches, pillars, etc all as specified and directed by Engr-in-charge.

M&L for PCC 1:3:6 type C-1 using 20mm graded crushed stone aggregate ) block masonry with solid block exc 10cm in width and set as in wall etc in CM 1:4 complete all as specified and directed by EIC.

M&L for Rendering 10mm thick on fair faces of brickwork or concrete surfaces in cement mortar (1:6) and finished even and smooth without using extra cement all as specified and directed by Engr-in-charge.

M&L preparing new plastered surfaces of walls and applying two coat oil bound distemper on walls all as specified and directed by Engr-in-charge.

M&L for Rendering 12mm thick on fair faces of brickwork or concrete surfaces in cement mortar (1:4) and finished even and fair without using extra cement all as specified and directed by Engr-in-charge.

M&L preparing new plastered surfaces of walls and applying two coats of cement base paint over a coat of primer all as specified and directed by Engr-in-charge.

M&L for 25mm thick Cement concrete (1:2:4) type B-0 (using 20mm graded stone aggregate) as in floor finishes all as specified and directed by Engr-in-charge.

M&L for 75mm thick Cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregate) as in sub-base in floor finishes all as specified and directed by Engr-in-charge.

Taking down carefully aluminium point wiring light, fan socket or power complete fitting such as switches, ceiling rose, fan regulator, socket including light fitting etc complete with MS conduit and T/W battern and depositing to MES store yard all as specified and as directed by Engineer-in-Charge.

M&L for point wiring with PVC insulated single core cable of stranded copper conductors of size 1.5 sqmm, 1100 volt grade drawn in and including rigid PVC casing caping accessories lain on wall/ceiling surface and fixed with PVC saddles and back-plate and GI screws, including PVC insulated single core cable of stranded copper conductor of size 1.5 sqmm as earth continuous wire connected to common earth and PVC Board for housing like switches, sockets, fan regulators etc all as directed for One light point controlled by one switch

One 3 pin 5 amps socket outlet independent with cables 1.5 sqmm size

One 3 pin 5 Amp socket outlet on same board.

All same as per item No 43 above but with conductor of size 4 sqmm (Nominal area) for one 3 pin socket outlet 15 Amps on independent board complete and earth continuity wire with 4 sqmm PVC insulated stranded copper conductor Cable. Note: Unit rate for cutting chases for conduit and sinking of boxes and making good to wall, floor ceiling complete all as specified and as directed by Engr-in-Charge.

S&F Switch Socket combination outlet 2 in 1, 3 pin, 5 and 15 amp flush type complete all as specified and directed.

S&F socket 2 in 1, 5 pin 5 Amp flush type complete all as specified.

S&F switch piano flush type 5 Amp, single pole, one way complete all as specified and directed.

M&L for ceiling rose surface Bakelite 65x50mm two to three terminal complete all as specified and as directed by Engr-in-Charge.

S&F LED luminaries light fitting single tube 1 x 20 watt, 4 feet long, with bipin holders with all accessories including LED tube rod 20W, internally pre-wired and including connecting electrically with 3 core PVC insulated sheathed flexible copper conductor cable to ceiling rose all as specified.

S & F LED light fitting 1x9W/1x10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size.

S&F sheet metal powder coated versatile double door SPN distribution board, 8 way suitable for MCB's fitted with copper bus bar rated 200amps, neutral link, earth bar and din rail suitable for use on 240 Volt, 50Hz.

M&L for MCB SPN 63 Amp, 240V with 10KA breaking capacity of 'C' series in distribution boards all as specified and directed.

S&F in repairs to MCB SP 6-32 Amp with 10KA breaking capacity of 'C' series in distribution boards all as specified and directed.

Earthing complete with galvanised steel earth plate electrode of size (600 x 600 x 6.3) mm thick buried directly into ground vertically to depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, surrounded on all sides by alternate layers of 150 mm thick charcoal and common salt, connected to galvanized earh lead wire of size 4.0 mm by means of lugs, bolts, nuts, washer, check nuts of galvanised iron or steel all as shown in Electrical plate No. 3, wire protected by dia 15 mm bore light grade GI Pipe laid in floor and fixed to wall with proper size of clamps and watering pipe of bore 20 mm dia GI light grade including wire mesh funnel, PCC, earth chamber pit with PCC 1:2:4 type B-1 using 20 mm grade stone aggreate including form work cement mortar including CI Pit cover with frame necessary excavation and earth work in any type of soil including testing on completion for desired result all as specified.

SASPOL LARJAY CONSTRUCTION