GE (N) P/TOKEN- 02 OF 2025-2026 SPL REPAIR TO RAIN WATER DRAINAGE SYSTEM AT LOC OF HQ 3 EW BDE, GURUDWARA ROAD AND PROVN OF TOILET FOR LADIES AND GENTS AT VICTORIA ROAD UNDER GE(NORTH) PUNE

Amount

Demolition of brick work / stone masonry / block masonry built in built in cement mortar or cement lime mortar complete all as specified and as diretced

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15 cm thickness (below or above ground level) complete all as specified and as diretced

M&L PCC (1:4:8) type D-2 as mass concrete as in foundation, mass concrete work complete all as specified and as diretced

M&L for PCC soild block masonry exeeding 10 cm in width built in CM (1:6) of Gde C-1 type 1:3:6 (20mm graded aggregate) complete all as specified and as diretced

All as per Item No 4 as above but except block masonry

Material and labour for rendering 15mm thick in cement mortar (1:4) on fair faces of brick or concrete surfaces with using water proofing compound finished even and smooth without using extra cement Complete all as specified and as directed.

Material and labour for rendering 10mm thick in cement mortar (1:4) on coping concrete surfaces of drain and manhole with using water proofing compound finished even and smooth without using extra cement all as specified and as directed.

Supply only integral water proofing compound.

M&L for PCC type B-1, 1:2:4 (20mm graded agg) as in copings, kneelers, apex stones,bed plates, kerbs water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and as diretced

Extra for forming fair finished drain or channel 60 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and as diretced

Demolition and breaking up drain pipes of any size and in any position (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as specified and as diretced

M&L in repair for 150mm bore RCC pipes, class NP2 laid and jointed with collars and tested including demolition of existing old one (salt glazed earthware, AC or reinforced pipes etc) set in cement mortar complete all as specified and as diretced

M&L for PCC 1:3:6 type C2 (using 40mm graded agg) concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested for 150mm dia of bore pipe complete all as specified and as directed.

M&L in repair for 200mm bore RCC pipes, class NP2 laid and jointed with collars and tested including demolition of existing old one (salt glazed earthware, AC or reinforced pipes etc) set in cement mortar complete all as specified and as diretced

M&L for PCC 1:3:6 type C2 (using 40mm graded agg) concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested for 200mm dia of bore pipe complete all as specified and as directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation, manholes etc and getting out in soft and loose soil complete all as specified and as diretced

Returning filling in including spreading levelling watering and well ramming in layers n.exc 25cm in dense/hard soil complete all as specified and as diretced

Removing the excavated surplus soil exceeding 5 km and depositing out of MOD Land complete all as specified and as diretced

M&L for cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting our existing benching for and forming branch channel (1/2 round or 3/4 section) in PCC(1:2:4) type B-1, smooth finished and reforming benching as required for any dia of pipe complete all as specified and directed.

Demolition of cement concrete (reinforced) in ground floors and pavings n.exc 15 cm thickness (below or above ground level) complete all as specified and as diretced

M & L for Precast cement concrete 1:2:4, type B1 (using 20mm graded stone aggregate) in cover slabs, for manholes , culverts slabs etc set in cement mortar 1:4, including use and waste of form work (einforcement shall be measured and paid for seperately) complete all as specified and as diretced

M & L for PVC (SWR) Pipe 75 mm bore as in spouts etc complete all as specified by Engr-in-Charge

M&L for mild steel framed work such as grill, gate etc with ends of bars shouldered or rebated or forged into spike framed guard bars barred iron doors, ladders, framed baluster, walk way, railing; frame work, including pintle hinges, stops, hand-made sliding bolts etc,sliding channels for sliding of gate and similar work conforming to Fe 290 Gde-E-165 complete all as specified & as directed.

M&L two coats of synthetic enamel paint on new steel surfaces over a coat of red oxide primer surfaces of any description exc 10 cm in witdth or girth complete all as specified and as diretced

M&L for preparation of new plastered or unplastered surfaces and applying two coats of cement base paint over a coat of primer complete all as specified and as diretced

Material and labour for designer coloured glossy chequered cement concrete tiles of size 30cmx30cmx25mm thick in floor, set, jointed and pointed in neat cement slurry over and including 20 mm thick screed bed in CM (1:6) including dismantling of existing tiles of any description or thickness laid bedded and pointed in cement mortar complete all as specified and as directed.

Material and labour for machine pressed precast cement concrete glossy interlocking paver block any shape and size as approved, 60mm thick, conforming to IS 15658-2006, M-35 with grey cement in floor/ pavement laid over and including 25mm thick sand cushioning laid dry to the profile including vibrating with surface vibrator after laying of tiles including dismantling existing blocks, tiles, removing rubbish off the premises complete all as specified and as directed. NOTE: (i) Manufacturers test certificate shall be submitted alongwith sample.

Surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out soft/loose soil complete all as specified and directed.

M&L for excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits,manholes, pier holes, etc. n.exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft/loose soil complete all as specified and as directed.

M&L for old size brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as speified and directed

M&L for 40mm thick DPC(Damp proof course) to horizontal or vertical surfaces in cement concrete 1:2:4 type B-0 (using 12.5mm graded agg) incl necessary form work over laying of polythene film 50 micron thick laid on a coat of bitumen primer @ 0.30 to 0.50kg/sqm complete all as specified and directed.

M&L for RCC (Nominal mix) 1:2:4 type B-1 (using 20mm graded agg) beams, cantilevers, bressummers, lintels incl necessary form work complete all as specified and directed.

M&L for MS TMT bars 6-8mm dia and over, cut to length, bent to shape required, incl cranking, bending spirally for hooping for columns, hooking ends and binding with and incl MS wire (annealed) not less than 0.9mm securing with clips complete all as specified and directed.

Use & formwork to sides and soffits of floor or roof beams, lintels, cantilevers, shelves and similar work etc complete all as specified and directed

M&L for 15mm thick cement plaster in CM 1:6 on bricks on concrete surfaces finishing the surfaces even and smooth without using extra cement with two coats of OBD over a coat of primer on new surface all as specified.

Removing excavated material n.exc 50m and depositing where directed at a level n exc. 1.5 m above the starting point of soil complete all as specified and directed

S&F for rolled mild steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) incl distance pieces, cleats etc. conforming Fe 410-W(Gde-E-250) quality-B complete all as specified and as directed.

S&F for 0.50mm thick pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet of any colour having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws with two corrugation side lap complete all as specified and as directed.

Excavation in post holes (or similar holes) each n.exc 0.5 cum getting out returning in and ramming earth or broken rubble mixed with earth around in layers n.exc 25cm soft/loose soil complete all as specified and as diretced

S&F 15mm bore tubes medium grade galvanized ISI marked with all fittings short pieces and fixed complete to walls, floor, ceiling etc complete all as specified and as diretced

S&F 20 mm bore GI tubing 'medium grade' galvanised, with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and as diretced

M&L for cutting chases, pinning in making good to faces where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, lintels etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good cutting n.exc 10cm girth on brick wall complete all as specified and as diretced

M&L Granite (of any type), 18- 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills,cooking platform,WHB plateform and like in cement mortar (1:4) incl pointing in white cement (1:2) using marble dust with admixer of pigment to match with marble shade including making full curving the edges and demolition existing stone slab complete all as specified and as diretced

S&F in white counter top Basin (self-rimming) Oval shape of size 550mm x 430mm x 195 mm fixed in position including waste coupling and PVC waste pipe, 32mm dia. complete Make: Parryware Model Aquarius, Cat Part No – C0466(SP) or of equivalent make

S&F in automatic ABS basic hand dryer(Make: dolphy Model No DAHD0011) of size 240x230x240mm complete fixed to wall complete all as specified and directed

M&L for vitreous china premium/ 1st quality Jaguar of size 370x670x720mm UF soft close slim seat floor mounted wash down water closet EWC white/ ivory/off white incl dual flush cistern fittings, health faucet alongwith two way bibcock and accessaries complete all as specified and as diretced. Make: Jaguar Model No LYS-WHT-38851S300 UFSMN

S&F for Jaguar vitreous china urinal half stall type (Cat Part No WHT-13261H) white or coloured including push cock and urinal spreder bowl top inlet with fixing stud connected to GI pipe etc complete all as specified and as diretced

S&F for Jaguar Basin Urinal Partition(Cat Part No JSE CHR-810UF60H19X ) including stinless steel brackets or necessary fixing on wall complete all as directed.

S&F PVC (SWR) soil, waste and vent pipes, 110 mm dia, in any length , single socketed,jointed with rubber ring joints/adhesive, fixed to wall, with PVC clamps, ISI marked complete all as specified and directed

S&F PVC (SWR) soil, waste and vent pipes, 75 mm dia, in any length , single socketed,jointed with rubber ring joints/adhesive, laid in trenches or in floors, ISI marked complete all as specified and directed

S&F PVC (SWR) bends, 110mm bore, any radius complete all as specified and directed

S&F PVC (SWR) bends, 75 mm bore, any radius complete all as specified and directed

S&F PVC (SWR) junction single (Single T) equal or 110 mm bore,

S&F PVC (SWR) junction single (Single T) equal or 75 mm bore,

S&F PVC vent cowl of 75mm dia complete all as specified and directed

M&L for 15 mm bore fancy type stop cock chromium plated cast copper alloy with wall flange complete all as specified and directed

S&F in hand shower (health faucet) of ABS body with 1.0m long easy flexible tube in chrome finish and wall hook complete all as specified and directed by Engr-in-charge. Make : Jaquar Cat No ALE-ESS-585 or of equivalent

S&F in two way bib taps with wall flange quarter turn suitable for 15mm bore pipe long body fancy type brass CP, screwed down screwed for iron pipe or brass ferrule complete all as specified. Make Johnson VIVA new series Cat part No: T4808C or of equivalent

S&F CP towel rail 600mm long fixed with and including chrome plated brass screws and wooden /plastic cleats complete all as specified and directed

M&L PVC connection 15mm size with PTMT nuts of length 600mm

S&F in 5mm thick bevelled edge looking mirror of size 1.20m x 0.80m fixed to wall with statinless screw with cap head complete all as specified and directed

S&F in aluminium powder coated fancy type decorative type curtain rod 25 mm bore all as specified and as directed.

S&F in aluminium powder coated fancy type decorative brackets suitable for 25 mm dia curtain rod (minimum projection from wall 75 mm ) fixed to wall including drilling, rawl plug, screws etc complete all as specified and as directed.

M&L for 100mm thick breaking brick or similar hardness materials or boulders to 63 mm gauge as in sub base complete all as specified and directed

M&L for 75mm thick PCC type B- 2, 1:2:4 (40mm graded aggregate) as in sub base/plinth protection etc complete all as specified and directed

M&L for double charged anti - skid ceramic tiles of each tile of size 600mm x 800mmx 8-10mm thick in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 15mm thick screed bed or bedding of layer in CM 1:6 complete all as specified.

M&L glazed ceramic coloured tiles of size 600 x 300 x 7-8mm thick, on vertical surfaces of walls such as skirting dado etc. set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick rendering in cement mortar 1:3 complete, all as specified.

M&L for machine pressed precast cement concrete coloured interlocking paver blocks, glossy rubber moulded, of triangular / Zigzag / Haxagone/any shape/design and size as approved, 60mm thick, conforming to IS 15658-2006, M-35 with grey cement and pigments grade in floor/ paths/ pavement laid over and including 25mm thick sand cushioning laid dry to the profile including filling the joints with sand of any description complete all as specified and as directed. NOTE: (i) Manufacturers test certificate shall be submitted alongwith sample.

M&L for factory made 100% solid wood plastic composite (WPC) door frame single rebated 90mm x 45mm made from wood plastic composite (Single extruded process) material with density 780kg/ cum all as directed. Note:-During fixing of chowkat, surface shall be make good in plumb with existing finishes like cement plaster wall tiles, floor tiles etc and as per ans site requirement fixed with screws not less than 50mm on existing chowkats or timber framed work complete all as specified and directed

S&F Factory made 100 % solid wood plastic composite(WPC) door frame, double rebate 125 mm x 45 mm made from wood plastic composite ( Single extruded process) material with density 780 Kg/ Cum, all as specified and directed.NOTE: During Fixing of chowkhat, surface Shall be make good in plumb with existing finishes like cement plaster, similar wall tile,floor tile etc and as per site reqd.

S&F in aluminium anodised powder coated ventilator using rectangular tube of size 63.50 x 25 x 1.50 mm including 3.50 mm thick designer glass louvers and stainless steel wire mesh 0.36 mm nominal dia of wire, average width of aperture 1.40 mm using ‘Jindal” aluminium section complete all as specified and directed by Engineer-in-Charge.

S&F for factory made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed

S&F for 125mm long aluminium anodised, barrel tower bolts of extruded section and fixed on door complete all as specified and directed

S&F for 250mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed on door complete all as directed

S&F for 100mm size butt hinges, cast brass,with mild steel hinge pin, bright polished and fixed, type B-11 fixed on chowkat with brass/stainless steel screws complete all as specified and as diretced

S&F for 125mm size extruded aluminium alloy handles, fabricated type,anodised fixed with screws on doors complete all as specified and as diretced

S&F in Pillar cock swan neck suitable for 15mm bore pipe long body fancy type brass CP with Capstan head screwed down screwed for iron pipe or brass ferrule quarter turn complete all as specified and as diretced. Make: Johnson Cat Part No T2804C Magna SERIES or of equivalent

S& in chromium plated bib cock with wall flange quarter turn complete all as specified and as directed. Cat No. FUS-29037 of make Jaquar ‘Fusion' series or of equivalent make as per Appx 'A' as approved by GE.

S&F in angle cock with flange quarter turn chromium plated cast copper alloy ISI marked, high pressure screwed down complete all as specified. Make: Johnson Eco Cat part No: T3910C or of equivalent make as per Appx 'A' as approved by GE.

S&F in chromium plated hand rail at bath room for senior citizen fixed on wall complete all as directed Make: ISI Marked or equivalent

S&F in 75mm bore PVC (SWR) floor trap plain with CP grating including jointing with solvent cement to waste pipe fixed in cement concrete type B-1, 1:2:4 using 20mm graded stone aggregate complete all as specified.

S & F in brass Chromium plated soap dish , fixed to wall with CP brass screws, all as specified and directed. Make: Johnson Fusion series Cat part No: T3252C or of equivalent make as per Appx 'A' as approved by GE

S & F in Brass Chromium plated towel rail all as specified and directed. Make: Johnson Fusion series Cat part No: T1350C or of equivalent make as per Appx 'A' as approved by GE

S&F in Brass Chromium plated towel ring all as specified and directed. Make: Johnson Fusion series Cat part No: T1351C or of equivalent make as per Appx 'A' as approved by GE

S & F rotational moulded polyethylene water storage tank 3 layer white colour waterr tank , non- toxic effect, algea formation protection (made frome Virgin grade of polyetjylene material which is duly stablized with anti-oxident Plastic) of capacity 500 litres, (cylindrical vertical one piece moulded with closed top), the internal and external surfaces of tanks are smooth, clean and free from any hidden internal defects, hoisted and fixed in position including S & F necessary GI fittings, inlet/outlet washout, overflow pieces long nipples, checknuts & washer, 20mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Min weight 210gms) and stop valves for 20mm bore pipe, cast copper alloy, screwed down high pressure with crutch or butterfly handle screwed both ends etc complete all as specified and directed. MAKE :-SINTEX

S&F 605 x 605mm grid for Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre. complete all as specified and directed.

S&F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified complete all as specified and directed.

M&L for Providing and fixing 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface over 2nd class soft wood fillets, or metal frame work and reinforced with G.I. wire mesh (Fillets, metal frame work and G.I. wire mesh paid separately)

M&L for preparation of new ceiling surfaces and two coats of oil bound distemper over a coat of primer complete all as specified and directed

M&L for excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits,manholes, pier holes, etc. n.exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft/loose soil complete all as specified and as directed.

M&L for 20mm thick plastering in two layers of CM 1:6 on brick or concrete wall surfaces etc with 2% of WPC on cement complete all as directed.(Note:WPC shall be measurned and paid in separatetly)

Supply only integral water proofing compound

S&F in repair for factory made 50 mm thick, 900mmX650mm manhole cover with additional frame for fixing, of precast RCC 1:2:4 type B-1 (using 20mm graded stone aggregate) finished the surface even and fare incl reinforcement MS TMT bars 6mm dia @ 150mm centre to centre both ways and set in CM 1:4 and handles including demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position complete all as specified and as directed.

Removing excavated soil n exc 50m and depositing where directed at a level n exc 1.5 m above the starting point.

M&L for Point wiring using FRLS-H PVC insulated unsheathed, multistranded copper conductor cable 1.5 sqmm drawn through and including PVC conduit of min 20 mm dia by Cutting chases for concealed conduits and sinking's for boxes and making good to walls, floors etc for concealed conduit wiring with modular flush box metal of GI sheet minimum 1.2 mm thick (ISI Marked) with earth terminal for safety, flush metal GI box of required modules as per site requirement and modular plate with support frame white in colour (ISI Marked) of required modules, 3mm thick including all fittings i.e. tees, bands and junction boxes, screws etc. complete for One light/Fan point controlled by one switch 6 Amps one way using cable (1.5 Sq mm for phase and neutral and 1.5 sq mm earthing) Note:- (a) wiring shall be done by using colour coding (b) Earth wire shall be of green colour. (Make:-Finolex/Anchor/Grandlay/Polycab/L &T)

All as item No 95 above One 3 pin socket outlet, 5 Amp socket outlet on same board with other switches.

All as per item No 95 above but One 3 pin socket outlet, 5 Amp socket outlet on independent board.

One 3 pin 15 Amps socket outlet independent, using FRLS-H PVC insulated unsheathed, multistranded copper conductor cable 2.5 sqmm drawn through and including PVC conduit of min 20 mm dia by Cutting chases for conduits and sinking's for boxes and making good to walls, floors etc for concealed conduit wiring with modular flush box metal of GI sheet minimum 1.2 mm thick (ISI Marked) with earth terminal for safety, flush metal GI box of required modules as per site requirement and modular plate with support frame white in colour (ISI Marked) of required modules, 3mm thick including all fittings i.e. tees, bands and junction boxes, screws etc. complete for power point controlled with cables, 2.5 sq. mm size (2.5 Sqmm for Phase and neutral and 2.5 Sqmm for earthing) (Make:-Finolex/Anchor/Grandlay/Polycab/L &T)

Supply and fixing modular Switch fabio classic white series/ Switch fabio classic white with indicator, ISI marked 16 AX Amps One Way switch complete all as specified and directed.(Make:- Cat Part No AHFSXXW161 of Havells or equivalent in Indoasian/Legrand/Anchor/Crabtree/Anchor/Roma)

Supply and fixing modular socket outlet fabio series 6 Amps 3 pin universal socket with child safety shutter, Shrouded terminals compatible with all standard mobile chargers, ISI marked for the same board complete all as specified and directed. (Make:- Cat Part No AHFKPXW063 of Havells or equivalent in Indoasian/Legrand/Anchor/Crabtree/Anchor/Roma)

Supply and fixing modular socket (Fabio classic white) outlet 16 Amps shuttered socket (heavy duty) 3 pin unversal socket with child safety shutter, Shrouded terminals, ISI marked for the independent board complete all as specified and directed. (Make:- Cat Part No AHFKCXW253 of Havells or equivalent Havells/Indoasian/Legrand/Anchor/crabtree/Anchor/Roma)

Supply and fixing modular Switch fabio classic white series/ Switch fabio classic white with indicator, ISI marked 6 AX Amps One Way switch complete all as specified and directed.(Make:- Cat Part No AHFSXXW061 of Havells or equivalent in Indoasian/Legrand/Anchor/Crabtree/Anchor/Roma)

Supply and fixing Sheet Metal enclosure double door for DBs when MCBs to be used SPN-8 Way with 200 Amp rated bus bar complete all as specified and directed. (Make:- Cat Part No 811818 of Indoasian or equivalent Havells/Indoasian/Legrand/Anchor/Roma)

Supply and fixing amp rating 240V, 10KA curve 'C' mini miniature circuit breaker (MCB) SPN and current carrying capacity 40 Amps in the MCB DB complete with connection testing and commissioning (Make: Havells Havells/Legrand/Anchor)

Supply and fixing amp rating 240V, 10KA curve miniature circuit breaker (MCB) SP and current carrying capacity 5-32 Amps in the MCB DB complete with connection testing and commissioning (Make:- Cat Part No 811818 of Indoasian or equivalent Havells/Indoasian/Legrand/Anchor/Roma)

Supply and fixing modular Ceiling Ceiling rose, 3 phase/PVC/polycarbonate, isolated body 50 x 65 mm surface type complete all as specified and directed. (Make:- Cat Part No AHLHXCW000 of Havells or equivalent Havells/Indoasian/Legrand/Anchor/crabtree/Anchor/Roma)

Supply & Fixing only LED lights fitting 20W LED 6000K (4Ft), 220V,AC decorative box type with driver, Aluminium extruded (Intervertor tubelight fittings) holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. (Make- Havells/Indoasian/Legrand/Anchor/Philips/Halonix)

M&L for Sub Main wiring complete with copper conductor, multi stranded, FRLS, PVC insulated and sheathed, 4 Sq mm, two run 1100 volts grade, incl drawn through PVC suitable size conduit and 4 Sqmm single run for earthing.(Make- Havells/Polycab/KEI/Finolex)

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete all as specified and directed

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16.0 sq mm 2 core

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete

S & F LED down light recess mounted luminare, round type 15 watts with efficiency of 100 lumens per watt, sleek design aluminium housing polycarbonate diffuser white finish operating voltage 150 V-270 V AC, 50 Hz all as per Make- Philips Cat Part No DN172B LED9S-6500 PSU, jaquar nero plus LNRP01R012XN or Havells complete all as directed by Engineer- in-charge

Supply and lay in repairs medium grade galvanized pipe with all fitting such as tee, bends, union elbow reducer in trenches, walls, roof etc including fittings, 25 mm (1”) dia. . :- Make:Tata,Jindal,Prakash Surya

Supply and fixing gun metal gate valve with iron head wheel head screwed both ends for iron pipe and fixed on 25 mm dia all as specified and directed.

M&L for cutting the existing GI tubing of size 40/32 mm dia for taking new connection of 25mm dia GI pipe complete withall fittings all as specified and directed.

Note : 1. Performance security:- Refer Condition 22 of Special Conditions. 2. Quoted Contract Sum shall be arrived at after deducting the amount of Credit Schedule (refer Schedule of Credit in pdf form for quantity, rate and amount etc.) for old unserviceable materials retrieved from site.

Gauri Associates (BID ID -3291816)

ANIL CONSTRUCTION CO. (BID ID -3291635)

Bright Electricals (BID ID -3295128)

N AND G CONSTRUCTION (BID ID -3292045)

M/s Asrani and sons (BID ID -3290555)

THE SAIRAM CONSTRUCTIONS (BID ID -3291247)

K.K.Enterprises (BID ID -3292034)