Comprehensive Upgradation Repair and Maintenance of 500 Residential Quarters in Bokaro Steel City Township, Jharkhand

Modified Estimated Cost after using Correction factor

Included in rate

on DSR 2023 on account of GST @0.973

Name of Work- Comprehensive Upgradation/Repair and Maintenance of 500 Residential Quarters in Bokaro Steel City

Township, Jharkhand

DSR 2023 DSR- AMOUNT (NON

SL NO ITEM DESCRIPTION UNIT QTY AMOUNT (DSR)

Ref No. 2023 DSR)

Building Civil Works

Earth work in excavation by mechanical means (Hydraulic excavator) /

manual means over areas (exceeding 30cm in depth, 1.5m in width as

2.6 well as 10 sqm on plan) including getting out and disposal of excavated

earth, lead up to 50m and lift up to 1.5m,as directed by Engineer-in-

Filling available excavated earth (excluding rock) in trenches, plinth, sides

of foundations etc. in layers not exceeding 20cm in depth, consolidating

each deposited layer by ramming and watering, lead up to 50 m and lift

Excavating, supplying and filling of local earth (including royalty) by

mechanical transport up to a lead of 5 km, also including ramming and

watering of the earth in layers not exceeding 20 cm in trenches, plinth,

sides of foundation etc., complete.

Supplying and filling in plinth with sand under floors, including watering,

ramming, consolidating and dressing complete.

Clearing jungle including uprooting of rank vegetation, grass, brush

wood, trees and saplings of girth up to 30 cm measured at a height of 1

m above ground level and removal of rubbish up to a distance of 50m

outside the periphery of the area cleared.

Supplying chemical emulsion in sealed containers including delivery as

6 2.34.1 Chlorpyriphos/ Lindane emulsifiable concentrate of 20% litre 150.00 251.25 37,687.94

Treatment of existing masonry using chemical emulsion @ one litre per

hole at 300 mm interval including drilling holes at 45 degree and plugging

them with cement mortar 1:2 (1 cement : 2 coarse sand) to the full

depth of the hole :

DSR 2023 DSR- AMOUNT (NON

SL NO ITEM DESCRIPTION UNIT QTY AMOUNT (DSR)

Ref No. 2023 DSR)

9 2.35.4.1 With Chlorpyriphos/Lindane E.C. 20% with 1% concentration. meter 500.00 46.02 23,011.45

Treatment at points of contact of wood work by chemical emulsion

Chlorpyriphos/ Lindane (in oil or kerosene based solution) @ 0.5 litres

per hole by drilling 6 mm dia holes at downward angle of 45 degree at

150 mm centre to centre and sealing the same.

Extra for levelling & neatly dressing of disposed soil completely as

directed by Engineer-in-Charge.

Reinforced Concrete work for counters

1:2:4 (1 cement : 2 coarse sand(zone-III) derived from natural sources : 4

12 4.1.3 graded stone aggregate 20 mm nominal size derived from natural cum 62.80 8432.36 5,29,541.63

Reinforced cement concrete work in beams, suspended floors, roofs

having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands,

plain window sills, staircases and spiral stair cases above plinth level up

13 5.3 to floor five level, excluding the cost of centering, shuttering, finishing cum 20.00 12314.34 2,46,286.73

and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-

III)derived from natural sources : 3 graded stone aggregate 20 mm

nominal sizederived from natural sources).

Centering and shuttering including strutting, propping etc. and removal

of form for :Shelves (Cast in situ)

Providing precast cement concrete Jali 1:2:4 (1 cement : 2 coarse

sand(zone-III) : 4 graded stone aggregate 6mm nominal size ), reinforced

with 1.6 mm dia mild steel wire, including centering and shuttering,

roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement:

3 fine sand) etc. complete, excluding plastering of the jambs, sills and

Steel reinforcement for R.C.C. work including straightening, cutting,

16 5.22A.6 bending, placing in position and binding all complete upto plinth level. kg 1500.00 115.43 1,73,147.78

Thermo Mechanically Treated bars of grade Fe-500D or more

Brick work with clay flyash F.P.S. (non modular) brick of class designation

17 6.32.2 7.5 in superstructure above plinth level up to floor five level in : Cement cum 50.00 9734.43 4,86,721.60

mortar 1:6 (1 cement : 6 coarse sand)

DSR 2023 DSR- AMOUNT (NON

SL NO ITEM DESCRIPTION UNIT QTY AMOUNT (DSR)

Ref No. 2023 DSR)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks

6.13 of class designation 7.5 in superstructure above plinth level up to floor V

18 6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) sqm 200.00 1202.80 2,40,560.63

DSR 2023 DSR- AMOUNT (NON

SL NO ITEM DESCRIPTION UNIT QTY AMOUNT (DSR)

Ref No. 2023 DSR)

Providing and fixing 18mm thick gang saw cut ( premoulded and

prepolished) machine cut for kitchen platforms, vanity counters, window

sills, facias and similar locations of required size of approved shade,

colour and texture laid over 20mm thick base cement mortar 1:4 (1

19 8.2.1.1 cement : 4 coarse sand) with joints treated with white cement, mixed sqm 30.00 3654.86 1,09,645.81

with matching pigment, epoxy touch ups, including rubbing, curing,

moulding and polishing to edge to give high gloss finish etc. complete at

Marble Area of slab over 0.50 Sqm.( For Counter)

Extra for fixing marble /granite stone, over and above corresponding

20 8.4 basic item, in facia and drops of width upto 150 mm with epoxy resin meter 66.91 608.52 40,718.49

based adhesive, including cleaning etc. complete.

Extra for providing opening of required size & shape for wash

basin/kitchen sink in kitchen platform, vanity counter and similar

21 8.5 location in marble/ Granite/ stone work, including necessary holes for nos 49.54 1047.50 51,897.78

pillar taps etc. including moulding, rubbing and polishing of cut edges etc.

Providing wood work in frames of doors, windows, clerestory windows

and other frames, wrought framed and fixed in position with hold fast

lugs or with dash fasteners of required dia & length (hold fast lugs or

dash fastener shall be paid for separately).

9.7.7 Float glass panes

24 9.7.7.1 4 mm thick glass pane (weight not less than 10 kg/sqm). sqm 450.00 2399.40 10,79,729.34

25 9.7.7.2 5.0 mm thick glass panes (weight not less than 12.50 kg/sqm). sqm 450.00 2783.26 12,52,467.74

Providing and fixing glazed shutters for doors, windows and clerestory

windows using 4 mm thick float glass panes (weight not less than 10 kg

per sqm) fixing with ISI marked M.S. pressed butt hinges bright finished

of required size with necessary screws.

9.9.1 Second class teak wood

DSR 2023 DSR- AMOUNT (NON

SL NO ITEM DESCRIPTION UNIT QTY AMOUNT (DSR)

Ref No. 2023 DSR)

9.20 Providing and fixing ISI marked flush door shutters conforming to IS :

2202 (Part I) decorative type, core of block board construction with

frame of 1st class hard wood and well matched teak 3 ply veneering with

vertical grains or cross bands and face veneers on both faces of shutters.

9.20.3 25 mm thick (for cupboard) including ISI marked nickel plated bright

27 finished M.S. Piano hinges IS : 3818 marked with necessary screws Sqm 642.18 3017.44 19,37,741.72

Providing and fixing ISI marked flush door shutters conforming to IS :

2202 (Part I) non-decorative type, core of block board construction with

9.21 frame of 1st class hard wood and well matched commercial 3 ply

veneering with vertical grains or cross bands and face veneers on both

faces of shutters:

30 mm thick including ISI marked Stainless Steel butt hinges with

necessary screws

Extra for providing lipping with 2nd class teak wood battens 25 mm

29 9.23 minimum depth on all edges of flush door shutters (over all area of door Sqm 100 494.85 49,485.32

shutter to be measured).

Providing and fixing M.S. grills of required pattern in frames of windows

9.48 etc. with M.S. flats, square or round bars etc. including priming coat with

approved steel primer all complete.

30 9.48.1 Fixed to steel windows by welding kg 100 234.50 23,450.27

31 9.48.2 Fixed to openings /wooden frames with rawl plugs screws etc. kg 10300 255.11 26,27,591.85

Providing and fixing fly proof galvanized M.S. wire gauge to windows and

9.51 clerestory windows using wire gauge with average width of aperture 1.4

mm in both directions with wire of dia 0.63 mm all complete.

32 9.51.1 With second class teak wood beading 62X19 mm sqm 100 1400.33 1,40,032.70

33 9.51.2 With 12 mm mild steel U beading sqm 100 1005.23 1,00,522.58

Providing 40x5 mm flat iron hold fast 400 mm long including fixing to

frame with 10 mm diameter bolts, nuts and wooden plugs and

embedding in cement concrete block 300x100x150 mm 1:3:6 mix (1

cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

DSR 2023 DSR- AMOUNT (NON

SL NO ITEM DESCRIPTION UNIT QTY AMOUNT (DSR)

Ref No. 2023 DSR)

Providing and fixing ISI marked IS:1341 M.S. pressed butt hinges bright

finished with necessary screws etc. complete :

Providing and fixing oxidised M.S. hasp and staple (safety type)

9.67 conforming to IS : 363 with necessary screws etc. complete (Copper

oxidised as per IS 1378)

Providing and fixing oxidised M.S. casement stays (straight peg type) with

necessary screws etc. complete (Copper oxidised as per IS 1378)

42 9.68.1 300 mm weighing not less than 330 grams No 3200 72.14 2,30,842.30

43 9.68.2 250 mm weighing not less than 280 grams Nos 3200 65.34 2,09,093.81

Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy

weight) with stainless steel screws etc. complete :

Providing and fixing chromium plated brass 100 mm mortice latch and

47 9.88 lock with 6 levers and a pair of lever handles of approved quality with Nos 15 1068.53 16,028.01

necessary screws etc. complete.

Providing and fixing chromium plated brass 50 mm cupboard or

wardrobe knobs with nuts complete.

Providing and fixing chromium plated brass handles with necessary

screws etc. complete:

DSR 2023 DSR- AMOUNT (NON

SL NO ITEM DESCRIPTION UNIT QTY AMOUNT (DSR)

Ref No. 2023 DSR)

Providing and fixing aluminium sliding door bolts ISI marked anodised

9.96 (anodic coating not less than grade AC 10 as per IS : 1868) transparent or

dyed to required colour or shade with nuts and screws etc. complete :

Providing and fixing aluminium tower bolts ISI marked anodised (anodic

9.97 coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed

to required colour or shade with necessary screws etc. complete :

Providing and fixing aluminium pull bolt lock, ISI marked, anodised

(anodic coating not less than grade AC 10 as per IS : 1868) transparent or

dyed of required colour and shade, with necessary screws bolts, nut and

washers etc. complete.

Providing and fixing aluminium handles of approved make anodized

9.1 (anodic coating not less than grade AC 10 as per IS : 1868) transparent or

dyed to required colour or shade with necessry screws etc. complete.

Providing and fixing aluminium hanging floor door stopper ISI marked

anodised (anodic coating not less than grade AC 10 as per IS : 1868)

transparent or dyed to required colour and shade with necessary screws

59 9.101.1 Single rubber stopper Each 1000 42.38 42,383.88

DSR 2023 DSR- AMOUNT (NON

SL NO ITEM DESCRIPTION UNIT QTY AMOUNT (DSR)

Ref No. 2023 DSR)

Providing and fixing factory made uPVC door frame made of uPVC

extruded sections having an overall dimension as below (tolerance

±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door

frame to be Jointed with galvanized brackets and stainless steel screws,

9.117 joints mitred and Plastic welded. The hinge side vertical of the frames

reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1

mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame

complete as per manufacturer’s specification and direction of Engineer

60 9.117.1 Extruded section profile size 48x40 mm Rmt 396 289.20 1,14,521.24

9.118 Providing and fixing to existing door frames.

24 mm thick factory made PVC door shutters made of styles and rails of

a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2

mm) with inbuilt edging on both sides. The styles and rails mitred and

joint at the corners by means of M.S. galvanised/ plastic brackets of size

75x220 mm having wall thickness 1.0 mm and stainless steel screws. The

styles of the shutter reinforced by inserting galvanised M.S. tube of size

20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of

'H' section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2

mm) wall thickness, fixed to the shutter styles by means of

plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC

multi-chambered single panel of size not less than 620 mm, having over

all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels

filled vertically and tie bar at two places by inserting horizontally 6 mm

galvanised M.S. rod and fastened with nuts and washers, complete as

per manufacturer's specification and direction of Engineer-in-charge.

(For W.C. and bathroom door shutter).

DSR 2023 DSR- AMOUNT (NON

SL NO ITEM DESCRIPTION UNIT QTY AMOUNT (DSR)

Ref No. 2023 DSR)

Providing and fixing factory made Fiberglass Reinforced Plastic (F.R.P.)

Chhajja 4mm thick of required colour size and design made of Resin

Transfer moulding (RTM)Machine technology, resulting in void free

compact laminate in single piece, having smooth gradual slope curvature

for easy drainage of water and duly reinforced by 2 nos vertically and 1

no horizontally mm thick MS flat with 12mm inbuilt hole for grouting on

the existing wallalongwith 50mm flangesduly inserted and sealed in the

wall completein one single piece casted monolithically, including all

necessary fittings. The FRP chhajja should be manufactured using

unsaturated polyester resin as per IS: 6746, duly reinforced with fiber

glass chopped strand mash (CSM) as per IS:11551 complete with

protective Gel coat U/V coating on top for complete resistance from the

extreme of tempetrature, weather & sunlight (only plan area of chhajjas

shall be measured for making payment)

Providing and fixing factory made uPVC glazed/wire mesh

windows/doors comprising of lead free uPVC multi-chambered frame,

sash and mullion/coupler (where ever required) extruded profiles having

minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and

2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any

shape, colour and design duly reinforced with galvanized mild steel

section made of required shape & size as per CPWD Specification, uPVC

extruded glazing beads, interlocks and Inline sash adaptor (where ever

9.147A required) of appropriate dimension, EPDM gasket, hardware, SS 304

grade fasteners of minimum 8 mm dia with countersunk head,

comprising of matching polyamide PA6 grade sleeve for fixing frame to

finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and

necessary stainless steel screws etc. Profile of frame, sash & mullion (if

required) shall be mitred cut and fusion welded/mechanically jointed

duly sealed at all corners, including drilling of holes for fixing hardware

and drainage of water etc.

DSR 2023 DSR- AMOUNT (NON

SL NO ITEM DESCRIPTION UNIT QTY AMOUNT (DSR)

Ref No. 2023 DSR)

After fixing frame the gap between frame and adjacent finished wall shall

be filled with weather proof silicon sealant over backer rod pf approved

size and quality, all complete as per approved drawing conforming to

CPWD specification & direction of Engineer-in-Charge.

Section of steel reinforcement and cross sections of uPVC profiles to be

as per design approved by Engineer-in-Charge. Wire mesh / Glazing of

plain/ toughened/ laminated/ double glass unit with / without high

performance coatings as per design requirements and conforming to IS:

3548 & IS:16231 shall be paid separately.

Note:- Structural design proof checked from a Government Engineering

Institute, to be provided by the manufacturer for:

(i) Sites with basic wind speed > 45 m/sec as per IS 875 - Part 3

(ii) Sites with structure height more than 20m for all wind speeds.

Two track two panels sliding window with Aluminium channel for roller

track, wool pile, nylon rollers with SS 304 body.

Using R2 series with frame (40mm & above) x (40mm & above) & sash

63 9.147.A1.1 (25mm & above) x (50mm & above) with zinc alloy (zamak) powder sqm 50.00 8882.26 4,44,112.96

coated touch locks with hook (Height upto 1.2 meter)

Ventilator Casement window single panel with or without fixed panel

9.147.D1 with S S. 304 friction hinges as per size and weight of sash, single point

locking zinc alloy (zamak) powder coated handles.

Using R1 series with frame (33mm & above ) x (35mm & above) & sash

64 9.147.D1.1 /mullion (33mm & above) x (50 mm & above). (Height upto 0.90 meter). sqm 50.00 14129.24 7,06,462.22

Casement window single panel with S.S. 304 friction hinges as per size

9.147.E1 and weight of sash, multi-point locking system, zinc alloy (zamak)

powder coated handles.

Using R2 series with frame (39mm & above) x (39mm & above) & sash

(39mm & above) x (60mm & above). (Height upto 1.2 meter)

Providing and fixing bright /matt finished Stainless Steel handles of

9.165 approved quality & make with necessary screws etc all complete.

DSR 2023 DSR- AMOUNT (NON

SL NO ITEM DESCRIPTION UNIT QTY AMOUNT (DSR)

Ref No. 2023 DSR)

Providing and fixing M.S. grills of required pattern in frames of windows

etc. with M.S. flats, square or round bars etc. including priming coat with

approved steel primer all complete. MS Grills for windows Fixed to

Fixing standard steel glazed doors, windows and ventilators in walls,

including fixing of float glass panes with glazing clips and special

metalsash putty of approved make, or metal beading with screws, (only

steel windows, glass panes cut to size and glazing clips or metal beading

with screws, shall be supplied by department free of cost.

Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete

70 10.10.1 block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded kg 100.00 88.25 8,824.62

stone aggregate 20 mm nominal size).

Providing and fixing T-iron frames for doors, windows and ventilators of

mild steel Tee-sections, joints mitred and welded, including fixing of

necessary butt hinges and screws and applying a priming coat of

approved steel primer.

Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete

71 10.13.1 block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded kg 100.00 151.66 15,166.15

stone aggregate 20 mm nominal size).

Welding by gas or electric plant including transportation of plant at site

DSR 2023 DSR- AMOUNT (NON

SL NO ITEM DESCRIPTION UNIT QTY AMOUNT (DSR)

Ref No. 2023 DSR)

Providing and fixing stainless steel ( Grade 304) railing made of Hollow

tubes, channels, plates etc., including welding, grinding, buffing, polishing

and making curvature (wherever required) and fitting the same with

necessary stainless steel nuts and bolts complete, i/c fixing the railing

with necessary accessories & stainless steel dash fasteners , stainless

steel bolts etc., of required size, on the top of the floor or the side of

waist slab with suitable arrangement as per approval of Engineer-

incharge, (for payment purpose only weight of stainless steel members

shall be considered excluding fixing accessories such as nuts, bolts,

fasteners etc.).

Brick on edge flooring with bricks of class designation 7.5 on a bed of 12

11.1 mm cement mortar, including filling the joints with same mortar, with

common burnt clay non modular bricks:

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded

75 11.3 stone aggregate) finished with a floating coat of neat cement, including

cement slurry, but excluding the cost of nosing of steps etc. complete.

11.3.1 40 mm thick with 20 mm nominal size stone aggregate sqm 1774.67 657.38 11,66,627.00

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300

mm or more (thickness to be specified by the manufacturer), of 1st

quality conforming to IS : 15622, of approved make, in all colours,

76 11.40 shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick sqm 250.00 1540.59 3,85,147.46

Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey

cement slurry @ 3.3 kg/ sqm including pointing the joints with white

cement and matching pigments etc., complete.

DSR 2023 DSR- AMOUNT (NON

SL NO ITEM DESCRIPTION UNIT QTY AMOUNT (DSR)

Ref No. 2023 DSR)

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS:

15622 (thickness to be specified by the manufacturer), of approved

make, in all colours, shades except burgundy, bottle green, black of any

size as approved by Engineer-in-Charge, in skirting, risers of steps and

dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse

sand) and jointing with grey cement slurry @ 3.3kg per sqm, including

pointing in white cement mixed with pigment of matching shade

Providing and laying Vitrified tiles in floor in different sizes (thickness to

be specified by the manufacturer) with water absorption less than 0.08%

and conforming to IS:15622, of approved brand & manufacturer, in all

colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4

coarse sand) jointing with grey cement slurry @3.3 kg/sqm including

grouting the joints with white cement and matching pigments etc. The

tiles must be cut with the zero chipping diamond cutter only . Laying of

tiles will be done with the notch trowel, plier, wedge, clips of required

thickness, leveling system and rubber mallet for placing the tiles gently

Double charge vitrified tile polished finish of size

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes

conforming to IS : 13592 Type A, including jointing with seal ring

conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i)

Single socketed pipes. 110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/

accessories for unplasticised Rigid PVC rain water pipes conforming to IS

81 12.42.4.2 : 13592 Type A, including jointing with seal ring conforming to IS : 5382, Each 300.00 236.91 71,073.27

leaving 10 mm gap for thermal expansion:Single tee with door

DSR 2023 DSR- AMOUNT (NON

SL NO ITEM DESCRIPTION UNIT QTY AMOUNT (DSR)

Ref No. 2023 DSR)

Providing and fixing on wall face unplasticised - PVC moulded fittings/

accessories for unplasticised Rigid PVC rain water pipes conforming to IS

: 13592 Type A, including jointing with seal ring conforming to IS : 5382,

leaving 10 mm gap for thermal expansion:Bend 87.5° 110 mm bend

Providing and fixing on wall face unplasticised - PVC moulded

fittings/accessories for unplasticised Rigid PVC rain water pipes

83 12.42.6.2 conforming to IS : 13592 Type A, including jointing with seal ring Each 30.00 141.12 4,233.57

conforming to IS : 5382, leaving 10 mm gap for thermal expansion:Shoe

(Plain) 110 mm Shoe

Providing and fixing unplasticised -PVC pipe clips of approved design to

unplasticised - PVC rain water pipes by means of 50x50x50 mm hard

12.43 wood plugs, screwed with M.S. screws of

required length, including cutting brick work and fixing in cement mortar

1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

Providing and fixing precoated galvanised iron profile sheets (size, shape

and pitch of corrugation as approved by Engineer-in-Charge) of total

coated thickness 0.50mm (base metal of minimum 0.45mm thickness

with total coating thickness of 0.05mm) with zinc coating 120 grams per

sqm as per IS:277, in 240 mpa steel grade, 5-7 microns epoxy primer on

both side of the sheet and polyester top coat 15-18 microns. Sheet

should have protective guard film of 25 microns minimum to avoid

scratches during transportation and should be supplied in single length

upto 12 metre or as desired by Engineer-in- charge. The sheet shall be

fixed using self drilling /self tapping screws of size (5.5x 55 mm) with

EPDM seal, complete upto any pitch in horizontal/ vertical or curved

surfaces, excluding the cost of purlins, rafters and trusses and including

cutting to size and shape wherever required.

DSR 2023 DSR- AMOUNT (NON

SL NO ITEM DESCRIPTION UNIT QTY AMOUNT (DSR)

Ref No. 2023 DSR)

Providing and fixing precoated galvanised steel sheet roofing accessories

of total coated thickness 0.50mm (base metal of minimum 0.45mm

thickness with total coating thickness of 0.05mm) with Zinc coating 120

12.51 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy

primer on both side of the sheet and polyester top coat 15-18 microns

using self drilling/ self tapping screws complete:

86 12.51.2 Flashings/ Aprons.( Upto 600 mm) meter 17.00 519.74 8,837.47

87 12.51.3 North light curves meter 17.04 584.49 9,959.14

88 12.51.4 Barge board (Upto 300 mm) meter 17.02 483.24 8,224.19

Gutter (600 mm over all girth)

13.1 12 mm cement plaster of mix :

15 mm cement plaster on the rough side of single or half brick wall of

13.16 6 mm cement plaster of mix : -

93 13.18 Neat cement punning sqm 500.00 85.57 42,785.24

Rough cast plaster upto 10 m height above ground level with a mixture

of sand and gravel or crushed stone from 6 mm to 10 mm nominal size,

dashed over and including the fresh plaster in two layers, under layer

13.19 12mm cement plaster 1:4 (1 cement: 4 coarse sand) and top layer 10

mm cement plaster 1:3 (1 cement: 3 fine sand) mixed with 10% finely

grounded hydrated lime by volume of cement.

94 13.19.1 Ordinary cement finish using ordinary cement sqm 4000.00 948.93 37,95,711.92

Extra for providing and mixing water proofing material in cement plaster per bag of

work in proportion recommended by the manufacturers. 50KG Cement

DSR 2023 DSR- AMOUNT (NON

SL NO ITEM DESCRIPTION UNIT QTY AMOUNT (DSR)

Ref No. 2023 DSR)

13.45 Finishing walls with textured exterior paint of required shade :

New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and

96 13.45.1 including priming coat of exterior primer applied @2.20kg/10 sqm. sqm 200.00 239.32 47,863.82

13.50 Applying priming coat :

With ready mixed aluminium primer of approved brand and manufacture

on resinous wood and plywood.

With ready mixed red oxide zinc chromate primer of approved brand and

98 13.50.3 manufacture on steel galvanised iron/steel works sqm 4200.00 72.14 3,02,980.52

Providing and applying white cement based putty 1mm on plaster

Wall painting with premium acrylic emulsion paint of interior grade,

having VOC (Volatile Organic Compound ) content less than 50 grams/

litre. of approved brand and manufacture, including applying additional

coats wherever required to achieve even shade and colour.

Applying priming coats with primer of approved brand and manufacture,

having low VOC (Volatile Organic Compound ) content.

With water thinnable cement primer on wall surface having VOC content

less than 50 grams/litre.

Removing white or colour wash by scrapping and sand papering and

13.88 preparing the surface smooth including necessary repairs to scratches sqm 67883.54 21.14 14,34,951.21

Painting with synthetic enamel paint of approved brand and

102 13.99.1 manufacture of required colour to give an even shade : One or more sqm 18000.00 110.03 19,80,483.12

coats on old work

DSR 2023 DSR- AMOUNT (NON

SL NO ITEM DESCRIPTION UNIT QTY AMOUNT (DSR)

Ref No. 2023 DSR)

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5

sq.meters and under, including cutting the patch in proper shape, raking

out joints and preparing and plastering the surface of the walls complete,

including disposal of rubbish to the dumping ground, all complete as per

direction of Engineer in-Charge With cement mortar 1:4 (1 cement : 4

Fixing chowkhats in existing opening including embedding chowkhats in

floors or walls cutting masonry for holdfasts, embedding hold fasts in

cement concrete blocks of size 15 x 10 x 10 cm with cement concrete

1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm

nominal size), painting two coats of approved wood preservative to sides

of chowkhats and making good the damages to walls and floors as

required complete, including disposal of rubbish to the dumping ground,

all complete as per directions of Engineer-In-Charge.

Providing and fixing bright finished brass casement window fasteners or

106 14.73 peg stays to windows/ ventilators with necessary welding and machine kg 50.00 596.37 29,818.56

screws etc. complete.

Repair to plaster of thickness 12mm to 20 mm in patches of area 2.5 sqm

and under, including cutting the patch in proper shape, raking out joints

and preparing plastering the wall surface with white cement based

polymer modified self curing mortar, including disposal of rubbish, all

complete as per the direction of Engineer-In- Charge.

Dismantling W.C. Pan of all sizes including disposal of dismantled

materials i/c malba all complete as per directions of Engineer-in Charge.

Dismantling 15 to 40 mm dia G.I. pipe including stacking of dismantled

109 14.84 pipes (within 50 metres lead) as per direction of Engineer in-Charge. meter 3000.00 3.48 10,435.43

(a) Internal Work- Exposed on wall

DSR 2023 DSR- AMOUNT (NON

SL NO ITEM DESCRIPTION UNIT QTY AMOUNT (DSR)

Ref No. 2023 DSR)

Taking out existing wooden door shutter, repair by cutting, painting etc.

and refixing of repaired door shutters to existing door frames, including

replacement of hinges with screws, etc. as required, all complete as per

the direction of the Engineer-in-charge

Dismantling works

Demolishing cement concrete manually/ by mechanical means including

111 15.2.2 disposal of material within 50 metres lead as per direction of Engineer - cum 91.00 1609.30 1,46,446.58

Demolishing R.C.C. work manually/ by mechanical means including

stacking of steel bars and disposal of unserviceable material within 50

metres lead as per direction of Engineer - in- charge.

Demolishing brick work manually/ by mechanical means including

113 15.7 stacking of serviceable material and disposal of unserviceable material

within 50 metres lead as per direction of Engineer-in-charge..

Dismantling doors, windows and clerestory windows (steel or wood)

shutter including chowkhats, architrave, holdfasts etc. complete and

stacking within 50 metres lead

Of area 3 sq. metres and below.

Dismantling tile work in floors and roofs laid in cement mortar including

115 15.23.1 stacking material within 50 metres lead. sqm 200.00 78.56 15,712.00

For thickness of tiles 10 mm to 25 mm

Dismantling barbed wire or flexible wire rope in fencing including making

rolls and stacking within 50 metres lead

Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China)

117 15.52 including stacking of useful materials near the site and disposal of each 200.00 119.93 23,985.42

unserviceable materials within 50 metres lead.

Dismantling old plaster or skirting raking out joints and cleaning the

118 15.56 surface for plaster including disposal of rubbish to the dumping ground sqm 5500.00 58.49 3,21,705.42

within 50 metres lead.

DSR 2023 DSR- AMOUNT (NON

SL NO ITEM DESCRIPTION UNIT QTY AMOUNT (DSR)

Ref No. 2023 DSR)

Disposal of building rubbish / malba / similar unserviceable, dismantled

or waste materials by mechanical means, including loading, transporting,

119 15.60 unloading to approved municipal dumping ground or as approved by Cum 960.00 282.51 2,71,205.46

Engineer-in-charge, beyond 50 m initial lead, for all leads including all

lifts involved.

Aluminium works -

Providing and fixing aluminium work for doors, windows, ventilators and

partitions with extruded built up standard tubular sections/appropriate Z

sections and other sections of approved make conforming to IS: 733 and

IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with

expansion hold fasteners including necessary filling up of gaps at

21.1 junctions, at top, bottom and sides with required PVC/neoprene felt etc.

Aluminium sections shall be smooth, rust free, straight, mitred and

jointed echanically wherever required including cleat angle, Aluminium

snap beading for glazing / paneling, C.P. brass / stainless steel screws, all

complete as per architectural drawings and the directions of Engineer-in-

charge. Glazing and paneling to be paid for separately) :

21.1.1 For fixed portion.

Powder coated aluminium (minimum thickness of powder coating 50

For shutters of doors, windows & ventilators including providing and

fixing hinges/ pivots and making provision for fixing of fittings wherever

required including the cost of EPDM rubber / neoprene gasket required

(Fittings shall be paid for separately)

Powder coated aluminium (minimum thickness of powder coating 50

Providing and fixing glazing in aluminium door, window, ventilator

shutters and partitions etc. with EPDM rubber / neoprene gasket etc.

complete as per the architectural drawings and the directions of

engineer-in-charge . (Cost of aluminium snap beading shall be paid in

With float glass panes of 4.0 mm thickness

DSR 2023 DSR- AMOUNT (NON

SL NO ITEM DESCRIPTION UNIT QTY AMOUNT (DSR)

Ref No. 2023 DSR)

Providing and laying water proofing treatment in sunken portion of WCs,

125 22.5 bathroom etc., by applying cement slurry mixed with water proofing

cement compound consisting of applying :

(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water

proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed

to air cure for 4 hours.

(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water

proofing cement compound @ 0.126 kg/sqm. This layer will be allowed

to air cure for 4 hours followed with water curing for 48 hours.

(The rate includes preparation of surface, treatment and sealing of all

joints, corners, junctions of pipes and masonry with polymer mixed sqm 418.60 660.43 2,76,458.49

Repair with New Technologies

Chipping of unsound/weak concrete material from slabs, beams,

columns etc. with manual Chisel and/ or by standard power driven

percussion type or of approved make including tapering of all edges,

126 26.28.1 making square shoulders of cavities including cleaning the exposed sqm 100.00 404.57 40,457.34

concrete surface and reinforcement with wire brushes etc. and disposal

of debris for all lead and lifts all complete as per direction of Engineer-In-

Charge. 75mm average thickness

Cleaning of reinforcement from rust from the reinforcing bars to give it a

total rust free steel surface by using alkaline chemical rust remover of

approved make with paint brush and removing loose particles after 24

hours of its application with wire brush and thoroughly washing with

water and allowing it to dry, all complete as per direction of Engineer-In-

DSR 2023 DSR- AMOUNT (NON

SL NO ITEM DESCRIPTION UNIT QTY AMOUNT (DSR)

Ref No. 2023 DSR)

Providing, mixing and applying bonding coat of approved adhesive on

26.31 chipped portion of RCC as per specifications and direction of Engineer-In-

charge complete in all respect.

129 26.31.2 Epoxy bonding adhesive having coverage 2.20 sqm/kg of approved make sqm 500.00 305.25 1,52,624.78

Total civil works 8,38,38,897.65 -

Sanitary & Plumbing

Providing and fixing water closet squatting pan (Indian type W.C.pan )

with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C.

flushing cistern, including flush pipe, with manually controlled device

(handle lever) conforming to IS : 7231, with all fittings and fixtures

complete, including cutting and making good the walls and floors

wherever required:

White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with

integral type foot rests

Providing and fixing white vitreous china pedestal type water closet

(European type W.C. pan) with seat and lid, 10 litre low level white P.V.C.

flushing cistern, including flush pipe, with manually controlled device

(handle lever), conforming to IS : 7231, with all fittings andfixtures

complete, including cutting and making good the walls and floors

wherever required :

131 17.2.1 W.C. pan with ISI marked white solid plastic seat and lid Nos 0.00 6973.59 -

Providing and fixing white vitreous china pedestal for wash basin

17.8 completely recessed at the back for the reception of pipes and fittings. Nos 0.00 1801.69 -

Providing and fixing CP Brass 32 mm size Bottle Trap of approved quality

& make and as per the direction of Engineer-in-charge.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per

IS:13983 with C.I. brackets and stainless steel plug 40 mm, including

painting of fittings and brackets, cutting and making good the walls

wherever required:

17.10.1 Kitchen sink with drain board

DSR 2023 DSR- AMOUNT (NON

SL NO ITEM DESCRIPTION UNIT QTY AMOUNT (DSR)

Ref No. 2023 DSR)

17.10.2 Kitchen sink without drain board

Providing and fixing white vitreous china water closet squatting pan

(Indian type) :

135 17.13.2 Orissa pattern W.C. pan of size 580x440 mm Nos 0.00 3391.83 -

Providing and fixing white vitreous china pedestal type (European type/

wash down type) water closet pan.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1

137 17.16A metre long with S.S. triangular plate to Eureopean type W.C. of quality Nos 100.00 373.70 37,369.52

and make as approved by Engineer - in - charge.

Providing and fixing a pair of white vitreous china foot rests of standard

pattern for squatting pan water closet :

Providing and fixing P.V.C. low level flushing cistern with manually

17.18 controlled device (handle lever) conforming to IS : 7231, with all fittings

and fixtures complete.

Providing and fixing solid plastic seat with lid for pedestal type W.C. pan

140 17.20.1 White solid plastic seat with lid Nos 40.00 732.99 29,319.80

Providing and fixing white vitreous china wash basin including making all

connections but excluding the cost of fittings :

141 17.25.1 Flat back wash basin of size 630x450 mm. Nos 2.00 1433.88 2,867.76

142 17.25.2 Flat back wash basin of size 550x400 mm. Nos 100.00 1062.38 1,06,237.98

144 17.25.4 Angle back wash basin of size 400x400mm. Nos 100.00 931.43 93,142.86

Providing and fixing P.V.C. waste pipe for sink or wash basin including

P.V.C. waste fittings complete.

17.28.2 Flexible pipe

147 17.29 Providing and fixing 100 mm sand cast Iron grating for gully trap. Nos 700.00 56.99 39,895.43

Providing and fixing 600x450 mm beveled edge mirror of superior glass

(of approved quality) complete with 6 mm thick hard board ground fixed

to wooden cleats with C.P. brass screws and washers complete.

DSR 2023 DSR- AMOUNT (NON

SL NO ITEM DESCRIPTION UNIT QTY AMOUNT (DSR)

Ref No. 2023 DSR)

Providing and fixing mirror of superior glass (of approved quality) and of

required shape and size with plastic moulded frame of approved make

and shade with 6 mm thick hard board backing :

Rectangular shape 453x357 mm

Providing and fixing 600x120x5 mm glass shelf with edges round off,

supported on anodised aluminium angle frame with C.P. brass brackets

and guard rail complete fixed with 40 mm long screws, rawl plugs etc.,

Providing and fixing trap of self cleansing design with screwed down or

hinged grating with or without vent arm complete, including cost of

cutting and making good the walls and floors :100 mm inlet and 100 mm

outlet Sand Cast Iron S&S as per IS: 1729

Providing and fixing PTMT Waste Coupling for wash basin and sink, of

approved quality and colour.

Waste coupling 31 mm dia of 79 mm length and 62 mm breadth

weighing not less than 45 gms.

153 17.70 Providing and fixing PTMT Bottle Trap for Wash basin and sink.

Bottle trap 31mm single piece moulded with height of 270 mm, effective

length of tail pipe 260 mm from the centre of the waste coupling, 77 mm

breadth with 25 mm minimum water seal, weighing not less than 260

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm

high and 112 mm distance from wall of standard shape with bracket of

the same materials with snap fittings of approved quality and colour,

weighing not less than 105 gms.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long,

200 mm wide with minimum distances of 37 mm from wall face with

concealed fittings arrangement of approved quality and colour, weighing

not less than 88 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to

17.73 wooden cleats with CP brass screws with concealed fittings arrangement

of approved quality and colour.

450 mm long towel rail with total length of 495 mm, 78 mm wide and

effective height of 88 mm, weighing not less than 170 gms.

DSR 2023 DSR- AMOUNT (NON

SL NO ITEM DESCRIPTION UNIT QTY AMOUNT (DSR)

Ref No. 2023 DSR)

Providing and fixing CPVC pipes having thermal stability for hot and cold

water supply including all CPVC plain and brass threaded fittings

including fixing the pipe with clamps at 1.00 mt spacing. this includes

jionting of pipes and fittings with one step CPVC solvent cement and the

cost of cutting chases and making good the wall same including testing of

joints complete as per the direction of engineer incharge

concealed work including cutting chases and making good the wall etc.

15 mm nominal outer dia pipes

159 18.8.2 20 mm nominal outer dia pipes rmt 1000.00 575.39 5,75,393.28

160 18.8.3 25 mm nominal outer dia .Pipes. rmt 1000.03 671.35 6,71,367.08

161 18.8.4 32 mm nominal outer dia .Pipes. rmt 1000.00 791.27 7,91,272.79

Providing and fixing ball valve (brass) of approved quality, High or low

pressure, with plastic floats complete :

Providing and fixing uplasticised PVC connection pipe with brass unions :

18.21.1 30 cm length

18.21.2 45 cm length

Providing and placing on terrace (at all floor levels) polyethylene water

storage tank, IS : 12701 marked, with cover and suitable locking

arrangement and making necessary holes for inlet, outlet and overflow

pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass bib cock of approved quality conforming

168 18.49.1 15 mm nominal bore. Each 0.00 542.43 -

Providing and fixing PTMT bib cock of approved quality and colour.

DSR 2023 DSR- AMOUNT (NON

SL NO ITEM DESCRIPTION UNIT QTY AMOUNT (DSR)

Ref No. 2023 DSR)

15 mm nominal bore, 165 mm long. Weighing not less than 110 gms.

Providing and fixing PTMT stop cock of approved quality and colour.

170 18.55.1 15 mm nominal bore, 86 mm long. Weighing not less than 88 gms. Each 1200.00 126.83 1,52,196.66

Providing and fixing PTMT pillar cock of approved quality and colour .

15mm nominal bore, 125 mm long foam flow. Weighing not less than

Providing and fixing C.P. brass long body bib cock of approved quality

172 18.51.1 conforming to IS standards and weighing not less than 690 gms. Each 50.00 855.12 42,755.81

15mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser

173 18.53.1 points of approved quality conforming to IS 8931 a) 15 mm nominal Each 50.00 614.67 30,733.66

Providing and fixing CP Brass shower rose with 15 or 20 mm inlet, 150

Dismantling old C.I. pipes including excavation and refilling trenches after

taking out the pipes, breaking lead caulked joints, melting of lead and

making into blocks including stacking of pipes at site lead upto 50 metre:

100 mm diameter C.I. pipe

Total Sanitary & plumbing works 1,21,27,160.87 -

Removal and cleaning of one or more vegetation/ plants from walls

roofs, chajja etc.up to 4 sqm area, chemically treatment of surface to

MR prevent further growth, and making good the surface by plaster , nos 400.00 704.28 2,81,712

grouting ,waterproofing , etc. as the case may be including necessary

scaffolding staging etc.