PROVN OF SLIDING MAIN GATE OF CIF (D) SIG REGT AND ADDN/ALTN TO BUILDING NO T-255 (TOILET BLOCK) FOR DELTA CAMP AT DHARMUND MIL STN UNDER AGE (I) BHALRA

Amount

Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, etc., and getting out any type of soil complete all as specified & directed by Engineer-in-Charge.

M&L for PCC 1:4:8 type D-2 (40mm graded aggregate) in foundation filling and mass concrete complete all as specified & directed by Engineer-in-Charge.

M & L for RCC M-25 design mix (20mm graded stone aggregate) in foundation including rafts, footing, foundation beams, plinth beams and mass concrete complete all as specified & directed by Engineer-in-Charge.

M & L for RCC M-25 design mix (20mm graded stone aggregate) in columns,pillar,piers,post and struts complete all as specified & directed by Engineer-in-Charge.

Use and waste of formwork to side of concrete foundation,footing,bases of columns,rafts and raft beams,side and soffit of foundation and plinth beams flat,for rough finished surfaces of concrete complete all as specified & directed by Engineer-in-Charge.

Use and waste of formwork to side of pillars,columns and stanchions,square or rectangular,for rough finished surface of concrete complete all as specified & directed by Engineer-in-Charge.

Returning filling in excavated material in to trenches around pipe after laying of pipes and testing complete incl watering and well remming in layers n exc 25 cm thick complete all as specified & directed by Engineer-in-Charge.

Removing surplus excavater soil to a distance n exc 50 m and deposting where directed at a level n exc 1.5 m above the starting point complete all as specified & directed by Engineer-in-Charge.

M&L for brick work with sub class B bricks, straight or curved on plan exc 6m mean radius built in CM1:6 complete all as specified & directed by Engineer-in-Charge.

Material & Labour for Rendering 15 mm thick cement plaster on fair surfaces of brick work or concrete surfaces in CM 1:4 finished to even and smooth sitfaces in without using extra cement incl complete all as specified & directed by Engineer-in-Charge.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified & directed by Engineer-in-Charge.

M&L TMT bars 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hookings ends and binding mild or securing with clips conform (Fe-410w or Fe-290) complete all as specified & directed by Engineer-in-Charge.

M&L mild steel TMT 6mm to 8mm dia as in striuups cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hookings ends and binding mild or securing with clips conform (Fe-410w or Fe-290) complete all as specified & directed by Engineer-in-Charge.

Rolled Mild Steel (Fe-410W(GdeE-250) quality) in Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete complete all as specified & directed by Engineer-in-Charge.

M&L for two coat of synthetic enamel paint over a coat of red oxide primer and preparation of new steel surface complete all as specified & directed by Engineer-in-Charge.

S&F Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified & directed by Engineer-in-Charge.

Surface excavation n. exc. 30cm deep and averaging 15cm deep and getting out in any type of soil complete all as specified & directed by Engineer-in-Charge.

M&L for 100 mm thick cement concrete 1:4:8, type B2 (using 40mm graded agg) as in path complete all as specified & directed by Engineer-in-Charge.

M&L for 15 mm thick screed bed or bedding layer of mortar in CM 1:4 for laying floor finishes. complete all as specified & directed by Engineer-in-Charge.

M&L for Chequered cement concrete tiles 30cm x 30cm x 25 mm thick , set, jointed and pointed in neat cement slurry as in floor/path etc with grey cement and pigments. complete all as specified & directed by Engineer-in-Charge.

Demolition of cement concrete (unreinforced) or tiling etc in ground floors and pavings n exc 15 cm thickness (below or above ground level)complete all as specified & directed by Engineer-in-Charge.

M&L for Brickwork withsub class B bricks(old size), straight or curved on plan any radius in half brick thick wall with old size bricks built in cement mortar 1:4 complete all as specified & directed by Engineer-in-Charge.

Use and waste of formwork to sides and soffits of floor or roof beam concrete fair finished surfaces complete all as specified & directed by Engineer-in-Charge.

Use and waste of formwork to chajjas, concrete fair finished surfaces complete all as specified & directed by Engineer-in-Charge.

M&L for Reinforced cement concrete M-25 design mix(using 20mm graded aggregates) in Beams,cantilevers, lintel over 1.5m span etc complete all as specified & directed by Engineer-in-Charge.

M&L for Reinforced cement concrete M-25 design mix(using 20mm graded aggregates) in chajjas etc complete all as specified & directed by Engineer-in-Charge.

Rendering 10 mm thick in cement and sand mortar 1:6 on other than fair faces of brick work or cement concrete surfaces including finishing the surface even and smooth without using extra cement complete all as specified & directed by Engineer-in-Charge.

Preparation of newly plastered surfaces of walls and applying three coats of white wash complete all as specified & directed by Engineer-in-Charge.

S&F for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ choowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs fasteners shall be paid for separately). complete all as specified & directed by Engineer-in-Charge.

Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door hutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and crew withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified & directed by Engineer-in-Charge.

S&F Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified & directed by Engineer-in-Charge.

Galvanized mild steel wire-cloth 0.56 mm nominal dia of wire and average width of aperture 1.00 mm and fixed with tinned tacks or galvanised wire staples complete all as specified & directed by Engineer-in-Charge.

03 mm thick figured (frosted) glass,pin headed ordinary quality and glazing with oil putty/wooden beads in square not exceeding 0.5 square metre in each pane complete all as specified & directed by Engineer-in-Charge.

S & F for Butt hinges, 100 mm long medium weight, cold rolled mild steel, ISI marked complete all as specified & directed by Engineer-in-Charge.

S & F for 250mm long aluminium alloy anodised sliding door bolt with hasp staple, bolt type, and fixing clips of sheet, cast or extruded sections & fixing bolts and sliding bolts of extruded section or cast aluminium alloy, ISI marked complete all as specified & directed by Engineer-in-Charge.

S & F for 150mm long, aluminium anodised, barrel tower bolts, of extruded section ISI marked complete all as specified & directed by Engineer-in-Charge.

S & F for Aluminium handles cast type anodised of size 150mm long ISI marked complete all as specified.complete all as specified & directed by Engineer-in-Charge.

Hard core of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick watered and well rammed to a true surface.complete all as specified & directed by Engineer-in-Charge.

M&L for 75mm thick PCC 1:4:8, type D-2 as in sub base for pavement, floor etc complete all as specified & directed by Engineer-in-Charge.

M&L for 25 mm thick PCC 1:2:4 type B-1, using 20 mm graded crushed stone aggregate, including finishing surface of concrete topping even and rough complete all as specified & directed by Engineer-in-Charge.

M&L for 75mm thick PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in plinth protection and similar works including finishing the surface of concrete topping even & fair, without using extra cement complete all as specified & directed by Engineer-in-Charge.

M&L for Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 15 mm thick screed bed in cement and sand mortar 1:6, complete all as specified & directed by Engineer-in-Charge.

M&L for Glazed coloured ceramic tile 450 x 300 x 7mm thick (coloured) on vertical surfaces such as skirting, dados etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 10 mm thick plaster in cement and sand mortar 1:4 complete all as specified & directed by Engineer-in-Charge.

Granite (of any type) work (table rubbed & polished) in steps, jambs, pillars, window-cills cooking platforms & like including pointing into white cement (1:2) using marble dust with admixture of pigment to match shade of granite laid over and including Screed bed or bedding layer of mortar 15mm thick for laying floor in CM 1:4 finished even & rough to receive top layer including rounding/bull nose to expose edge, complete all as specified & directed by Engineer-in-Charge.

Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified & directed by Engineer-in-Charge.

M&L for Rolled mild steel plates (plain or chequered), square cut or notched (ordinary or counter sunk) forming holes etc ofFe-290 (Gde E-165) complete all as specified & directed by Engineer-in-Charge.

S & F rolled section conforming to Fe-290 (Gde E-165) as in purlins,rafter,rails amd fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) incl distance pieces, cleats etc complete all as specified & directed by Engineer-in-Charge.

Dismantling of plain or corrugated AC sheeting, any gauge, thickness, including ridge etc as in roof covering.complete all as specified & directed by Engineer-in-Charge.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified & directed by Engineer-in-Charge.

Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified & directed by Engineer-in-Charge.

Supplied and fixed Rotational moulded polyethlene water storage tanks three layers of 1000 ltrs capacity ISI marked (cylindrical vergical with closed top) hoisted and fixed in position all as specified in SSR Part I including 20mm thick Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 20mm-210 gms including Dismantling of old brocken water tanks and refixing of inlet, outlet & over flow pipe etc complete all as specified & directed by Engineer-in-Charge.

S & F for Steel water tubing medium grade, galvanised, including short lengths, fixed to wall/concealed in wall/ceiling or laid in floor complete with all fittings such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc, of 15mm bore complete all as specified & directed by Engineer-in-Charge.

All as per Item 42 Above but 20mm bore.

Bib tap 15 mm bore short body, Brass CP, fancy type (long shank )., with crutch or butterfly handle screwed down screwed for iron/PVC pipe or for brass ferrule and fixed, complete all as specified & directed by Engineer-in-Charge.

Stop valve /Angle valve (ISI Marked), fancy type, chromium plated with long shank and cup screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron /PVC pipe or for unions of 15 mm bore and complete all as specified & directed by Engineer-in-Charge.

Stainless steel gratings 75mm bore size fixed with cement motar.complete all as specified & directed by Engineer-in-Charge.

S & F for Vitreous china wash hand basin flat back, size 630 x 450mm excluding pillar tap, waste fitting chromium plated brass and rubber plug, porcelain stopper, a pair of CI brackets, waste pipe and pillar tap etc., complete all as specified & directed by Engineer-in-Charge.

S & F for CP Brass fancy type Pillar taps, cast copper alloy, with capstan heads,chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed for 15mm bore complete all as specified & directed by Engineer-in-Charge.. Make : Hindware/Cera/Marc/Somany

Supply & fixed , Vitreous china wash down water closet pan (Pedestal pattern) white (excl fixing bolts, flushing cistern and flush pipe) but including plastic water closet seat, white, closed pattern with flat bottom and cover and mild steel CP or aluminised hinging device. complete all as specified & directed by Engineer-in-Charge.

S & F for PVC low level flushing cistern, valveless, syphonic action type, 10 litres capacity with inlet, ball valve float and handle with and including brackets & PVC bend pipe 60/90 cm long etc, supplied and fixed, complete all as specified & directed by Engineer-in-Charge.

Supply & fixed ,Vitreous China Urinal, Half stall type, white including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, , flush pipe, grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) fixed incl supply and fixing of CP coupling, waste pipe and cp brass spreder all necessary fittings, complete all as specified & directed by Engineer-in-Charge.

S & F for PVC connection 15 mm size, of length 450 mm, with PTMT nuts supplied and fixed complete all as specified & directed by Engineer-in-Charge.

S & F for PVC (SWR) pipes single socketed in any length with rubber ring joints fixed in trenches/floors/walls for 75 mm bore of pipe fixed complete all as specified & directed by Engineer-in-Charge.

All as per Srl Item No 64 Above but 110mm bore of pipe.complete all as specified & directed by Engineer-in-Charge.

S & F for PVC (SWR) floor bend, plain including jointing with solvent cement 75 mm bore complete all as specified & directed by Engineer-in-Charge.

All as per Srl Item No 66 Above but 110mm bore of pipe.complete all as specified & directed by Engineer-in-Charge.

S & F for PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75 mm bore complete all as specified & directed by Engineer-in-Charge.

S&F PVC (SWR) vent cowl of 75mm dia complete all as specified & directed by Engineer-in-Charge.

M/S SUSHEEL KUMAR Govt. CONTRACTOR (BID ID -3396752)

VEER TRADERS (BID ID -3401078)

M/S Virinder Sharma (BID ID -3398910)