SPECIAL REPAIR OF BLDG NO P-48 (SINGLE OFFRS ACCN), DRAIN OF 271 TRANSIT CAMP, PROVN OF RAMP (DOUBLE FOR B VEH) AND INTERNAL DRAINAGE SYSTEM FROM BASKETBALL GROUND TO BOUNDARY WALL OF MAP ACCN AT MIL STN KALKA UNDER GE (I) JUTOGH

Amount

Taking down cement plaster on any description on brick or stone wall etc, incl hacking out joints for key, scrubbing with water etc., complete all as specified and directed.

M&L for Rendering 15 mm thick on brick or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement, complete all as specified and directed.

M&L for Rendering 10 mm thick on ceiling in cement mortar (1:3) finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4, on concrete surfaces finished even and fair without using extra cement including mixing of water proofing compound of approved make as per manufacturers instructions on existing surfaces, complete all as specified and directed.

M&L for three coats of white wash including preparation of new plastered on Ceiling surfaces of any description, complete all as specified and directed.

M&L for one coats of white wash including preparation of old plastered on ceiling surfaces of any description, complete all as specified and directed.

M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/liter and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 liter/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 liter/ 10 sqm over new surfaces, complete all as specified and directed.

M&L for complete removal of existing treatment and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/liter and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 liter/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 liter/ 10 sqm over new surfaces. applying two coats of cement base paint on wall incl preparation of surfaces and coat of primer with alkali- resistant priming paint, complete all as specified and directed.

M&L for complete removal of existing treatment and applying two coats of oil bound distemper on wall over primer over 1-2 mm (av-1.5 mm Thick wall care putty to achieve smooth and even surface incl preparation of surface, complete all as specified and directed.

M&L for applying two coats of oil bound distemper on wall over primer over 1-2 mm (av-1.5 mm Thick wall care putty to achieve smooth and even surface incl preparation of new plastered surface, complete all as specified and directed.

Supply only Integral water proofing compound, complete all as specified and directed.

M&L for cleaning of roof slab surfaces including sweeping clean & washing down with water to remove dust & providing water proofing treatment with polymeric standard water proofing membrane, complete all as specified and directed. (a) M&L preparation of plaster surfaces /RCC roof surfaces and applying one coat of oil bound bituminous primer @0.03 ltr/Sqm (b) M&L applying blown type bitumen @1.20Kg/Sqm of grade 85/25 (c) Supplying and laying modified polymeric water proofing membrane super thermo lay 3mm thick of weight not less than 3.00kg /sqm reinforced with polyester non woven fabric weight not less than 150gm/sqm center core including coping on the surfaces with torch application of membrane with 10cm over laps as required. (d) Applying two coats of aluminium paint @ 0.2 kg/sqm.

Dismantling floor hearth and wall tiling incl cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

M&L for Non Skid ceramic colored tiles 7 to 8 mm thick(square/ rectangular) area of each tile exceeding 0.11 sq m but not exceeding 0.18 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15 mm thick screed bed in CM 1:6 complete all as specified.

M&L for non skid ceramic tile of approved shade and pattern 7mm to 8mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10mm thick backing coat with CM 1:4, complete all as specified and directed.

M&L for glazed ceramic tiles in vertical surface 450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and incl provn of 10 mm thick backing coat in CM 1:4, complete all as specified and directed.

Demolition of cement concrete (un-reinforced ) in ground floor and paving not exc. 15 cm thick (below and above ground level) complete all as specified and directed.

M&L for 75mm thick, PCC 1:4:8, Type D-2, using 40mm graded crushed stone aggregate as in sub base of floor, complete all as specified and directed.

Taking down chowkhats or frames n.exc 1.5 sqm (without taking off shutter from the frame) each and removing from the site including dismantling brick work for hold fasts etc., complete all as specified and directed.

Taking down chowkhats or frames exc 1.5 sqm but n.exc 4 sqm (without taking off shutter from the frame) each and removing from the site including dismantling brick work for hold fasts etc., complete all as specified and directed.

S&F steel windows of profile rectangular tube section with side hung shutters incl projecting type hinges with steel handles, MS peg stay with glazing bars, complete all as specified and directed.

S&F steel windows of profile rectangular tube section with side hung shutters incl projecting type hinges with steel handles, MS peg stay without glazing bars, complete all as specified and directed.

S&F steel windows or ventilators, fixed type, with glazing bars, complete all as specified and directed.

S&F for Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders framed balusters, walk ways, railings and similar work conforming to Fe-290 Gde-E-165, complete all as specified and directed.

S&F 3 mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq.m in each pane, complete all as specified and directed.

All as per Srl item No 25.00 above but exc 0.5 sqm in each pane for aluminium windows, complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staplesor MS beads size 2mm to 3mm, complete all as specified and directed.

S&F pressed steel frames of size 125 x 60 mm for doors with one or more rebates including supply & fixing lugs,125 mm size including MS hinges, lock strike plate, etc., complete all as specified and directed.

S&F pressed steel frames of size 105 x 60 mm for doors with one or more rebates including supply & fixing lugs,125 mm size including MS hinges, lock strike plate, etc., complete all as specified and directed.

M&L for PCC 1:3:6, type C-1, using 20mm graded mechanically crushed stone aggregate as in filling pressed steel frame /hold fast blocks etc complete all as specified and directed.

S&F 35mm thick flush shutter, solid core construction with block board core and plywood face panels, both faces are covered with decorative face veneer with lipping/ frame to match , complete all as specified and directed.

S&F for Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodized aluminum snap beading & not less than 50 micron of powder coating etc., complete all as specified and directed.

S&F aluminium sliding windows with 50 micron powder coating, three track sliding windows with two glazed shutters, 5mm thick tinted glass ordinary quality and one shutter of stainless steel wire mesh 0.36mm nominal dia of wire and average width of aperture 1.40mm including good quality of bearing handle, locks, including EPDM gasket to render the glazing, air and water tight etc complete all as specified and as directed. catalogue numbers of Jindal company or equivalent make as specified. Three track bottom - 20957, Three track top/vertical-20958, handle-20606, Interlocking-20605, Top and Bottom - 20604, complete all as specified and directed.

S&F factory made extruded aluminium ventilators with 50 micron powder coating of frame of 63.5x38.10x1.29 mm including 5mm thick tinted glass ordinary quality and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beads 20mm size, complete all as specified and directed.

S&F granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete in cupboard shelfs, steps, jambs, pillars, window cills, cooking's platforms and like complete all as specified and directed.

S&F 35 mm thick factory made glazed & Skelton shutter of IInd class H/Wood open rebated & prepared to receive glass or gauze etc without sash bar open rebated with edges of framing plain, chamfered or rounded, fitted with cut & mitered beads for securing glass or gauge etc size of stiles rails etc as specified in sec 8 clause 8.24 (a) of SSR Part-I (2010), complete all as specified and directed.

S&F for factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 45x85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length, complete all as specified and directed. i) M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately. ii) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F for 35mm thick Factory made single extruded WPC (Wood Polymer Composite) solid Moulded WPC door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N edge),minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed. Note: Stainless steel butt hinges and necessary S S screws shall be paid separately.

S&F brass door magnet/ door catcher for cabinet cupboard /ward droobe, kitchen including suitable screws for fixings complete all as specified and directed.

S & F for 125 mm Hasp and staple, safety type, of aluminium anodised with incl hinges pin including bolt to hinge plate and fixed with screws complete all as specified and directed .

S&F stainless steel butt hinges medium weight, cold rolled, 100mm, complete all as specified and directed.

S&F 150mm long aluminium anodized, barrel tower bolt of extruded section, complete all as specified and directed.

S&F 200 mm aluminium anodized, barrel tower bolts of extruded section, complete all as specified and directed.

Supply and fix 100mm size aluminum handle fabricated, 'D' type, anodized ISI marked complete all as specified and directed.

Supply and fix 150mm size aluminum handle fabricated, 'D' type, anodized ISI marked complete all as specified and directed.

S&F 250mm long aluminium alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy, complete all as specified and directed.

S&F 300mm long aluminium alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy, complete all as specified and directed.

S&F 300 mm MS ordinary rat tail rod pattern springs incl roller and roller plate fixed to wooden chowkhats or welded to angle iron door frames, complete all as specified and directed.

M&L for preparation of new surfaces of steel and applying two coat of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

M&L for preparation of Old surfaces of steel and applying two coat of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

M&L for preparation of new wooden surface of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer, complete all as specified and directed.

S&F in repair vitreous china squatting pan of “Orissa Pattern” of size 580x440mm coloured with integral footrest complete including making good floors, complete all as specified and directed.

S&F in repair 10 liters capacity, PVC valve less, symphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and suitable flush pipe PVC 32mm dia, complete all as specified and directed.

S&F in repair vitreous china wash hand basin white flat back of size 550x440mm including CI brackets, chromium plated waste coupling, waste pipe of size 32mm dia etc., (incl all waste fittings), complete all as specified and directed.

S&F for Brass CP Mixer valve for mixing hot and cold water screwed down for wash hand basin, complete all as specified and directed.

S&F in repair 15 mm fancy type chromium plated fancy type bib tap brass long body with flange screwed down high pressure CP cast copper alloy with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union, complete all as specified and directed.

S&F in repair stainless steel grating open able 100mm sqmm size with/without hole including fixing with white cement, complete all as specified and directed.

S&F in repair 15mm bore, fancy type, chromium plated Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and directed.

S&F in repair brass chromium plated, towel rail, 20mm dia, D type, 60cm long between flanges, complete all as specified and directed.

S&F for PVC connections 15mm size with PTMT nuts of length 450mm, complete all as specified and directed.

S&F in repair for Chromium plated brass shower rose 125 mm size with or without swivel joints including fixing with 15 mm bore pipe, complete all as specified and directed.

S&F in repair pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for 15mm bore iron pipe, complete all as specified and directed.

S&F PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe 32mm bore suitable for wash hand basins/sinks, complete all as specified and directed.

S&F in repair 110mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, complete all as specified and directed.

S&F in repair 75mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, complete all as specified and directed.

S&F in repair PVC (SWR) floor trap 75mm, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F in repair PVC (SWR) junction single, (Single T 110mm), equal or unequal with access door, complete all as specified and directed.

S&F in repair PVC (SWR) junction single, (Single T 75mm), equal or unequal with access door complete all as specified and directed.

S&F in repair PVC (SWR) bends, for 110mm bore pipes, with access doors, complete all as specified and directed.

S&F in repair PVC(SWR) bends, for 75mm bore pipes, with access doors, complete all as specified and directed.

Dismantling water tanks of capacity exc 250 & n.exc 500 ltrs and removing from site to store, complete all as specified and directed.

S&F Rotational moulded polythene water storage tank triple layered (cylindrical vertical with closed top) hoisted and fixed in position on roofs complete all as specified in SSR Part-1, capacity 500 ltrs, complete all as specified and directed.

S&F Ball valve of brass, 20mm bore, high pressure with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed, complete all as specified and directed.

S&F CI Gate valve, 20mm bore, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or unions, complete all as specified and directed.

S&F in repair CP brass soap dish, complete all as specified and directed.

Taking up or down steel tubing and connection 15 mm bore pipe and removing from site, complete all as specified and directed.

Taking up or down steel tubing and connection 20 mm bore pipe and removing from site, complete all as specified and directed.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth, complete all as specified and directed.

S&F 15mm dia tubes medium grade, galvanized, with all fittings such as sockets, bends, elbows, tees etc, concealed/surface fixed to walls and ceiling or laid in floors, complete all as specified and directed.

S&F 20mm dia tubes medium grade, galvanized, with all fittings such as sockets, bends, elbows, tees etc, concealed/surface fixed to walls and ceiling or laid in floors, complete all as specified and directed.

PVC (SWR) vent cowl,110 mm Dia, complete all as specified and directed.

Demolition of cement concrete (reinforced) in roofs, floors (other than ground floors) beams, slabs, staircases, landing, chajjas and similar suspended item, complete all as specified and directed.

Use and waste of form work to chajjas/Lintel beam or any other RCC work for fair finish surfaces, complete all as specified and directed.

M&L for RCC 1:1.5:3, type A-1, using 20mm graded mechanically crushed stone aggregate as in chajjas/ lintel/ beam etc., complete all as specified and directed.

S&F MS TMT bar 10mm dia & over, cut to length bent to shape required including cranking, bending spirally for hopping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for PCC 1:2:4, type B-0, using 12.5mm graded mechanical crushed stone aggregate for benching, coping shall be 150mm in radius mixed with acrylic based polymer water proofing compound, complete all as specified and directed. Note: WPC shall be measured and paid separately.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws, complete all as specified and directed.

M&L for mild steel as in framed work as in doors or gates of angle or other section with gusset plates, rails, braces,etc., complete, drilled for fixing of steel sheeting or other covering doors, etc., to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging; also fastening and fixing conforming to Fe-290 Gde E-165, complete all as specified and directed.

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, but exc 10 cm and not exc 15 cm long with Dia of neck 11-15 mm, complete all as specified and directed.

Demolition of brick or stone masonry, built in cement mortar incl all quoins, pillars, arches etc but excluding ashlars facing, complete all as specified and directed

M&L for brick work with sub class 'B' bricks, straight or curved on plan exc. 6 m mean radius, built in CM (1:6), complete all as specified and directed..

M&L for reuse old brick for brick work with sub class 'B' bricks, straight or curved on plan exc. 6 m mean radius, built in CM (1:6) complete all as specified and directed. (Except bricks)

M&L for brick work with sub class‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4, complete all as specified and directed.

Cutting openings, through brick walls for door, window and other openings or enlarging existing openings. converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc. to store and rubbish not exc. 50m, complete all as specified and directed.

Forming jambs, etc. to openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work, complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6, type C-2, using 40mm graded crushed stone aggregate as in plinth protection, complete all as specified and directed.

M&L for chequered cement concrete tiles pre polished 20cmx20cmx25mm thick, set, jointed and pointed in neat cement slurry with grey cement and pigment in floors incl 15mm thick screed bed or bedding layer in CM 1:6, complete all as specified and directed.

M&L for 100mm thick PCC 1:4:8, type D2, using 40mm graded crushed stone aggregate as in flooring, complete all as specified and directed.and directed.

M&L for providing and laying 60 mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed.

Excavation in trenches not exc. 1.50m wide and not exc. 1.50m depth for foundation, etc or for manholes/sewage lines etc, n.exc 10 sqm on plan and getting out in hard/dense soil, complete all as specified and directed.

M&L for PCC 1:4:8, Nominal mix using 40 mm graded crushed stone aggregate as in foundation, filling and mass concrete complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm in hard/ dense soil, complete all as specified and directed.

Removing excavated material n exc.50m and deposited where directed at a level n exc 1.5 m above the starting point in soils, complete all as specified and directed.

Demolition and breaking up any 150mm drain pipes (salt glazed ware, AC, reinforced Concrete) set in cement mortar, complete all as specified and directed.

M&L for 150mm dia Reinforced concrete pipes, class NP3, laid and jointed complete with collars, complete all as specified and directed.

M&L for concrete bed to drain pipes of 150mm dia including packing under, and haunching against the sides of pipes after they are laid and tested in cement concrete 1:3:6, type C-2, complete all as specified and directed.

M&L for PCC 1:2:4, type B-1, using 20 mm graded crushed stone aggregate as in cover slabs placed in position over manholes etc including use and waste of necessary formwork, complete all as specified and directed. Note:- Reinforcement and handles shall be measured and paid separately.

M&L for TMT bars 6 to 8mm dia and over cut to length bent to shape required and binding with ms wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

M&L for PCC 1:3:6, type C-1, 20mm graded crushed stone aggregate as drain PCC incl fair finished drain or channel using extra cement including forms, moulds, mitered/stopped ends etc., complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitered/ stopped ends etc., complete all as specified and directed.

Add or deduct for each 25 mm girth or part there off over or under 30cm ditto, complete all as specified and directed.

Demolition of cement concrete(unreinforced) of any description and in any position not other wise, complete all as specified and directed.

M&L for brick work with subclass `B' old size bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:4, complete all as specified and directed.

M&L for brick work, with sub class 'B', bricks in one brick thick honey comb built in cement mortar (1:4) complete all as specified and as directed .

M&L for PCC 1:2:4, type B - 0, using 12.5mm graded crushed stone aggregate as in coping incl necessary formwork, weathering, slightly rounded or chamfered angles, complete all as specified and directed.

Use and waste of flat form work to faces of walls, retaining walls, abutments, parapets and staircase railing and similar works incl attached pillasters, buttresses etc. Vertical or to batter etc. (rough finished surface), complete all as specified and directed..

Excavating Over areas, n.exc 1.5 m deep and getting out in hard/ loose soil., complete all as specified and directed.

M&L for 75mm thick cement concrete 1:2:4, type B-1, using 20mm graded crushed stone aggregate as in flooring complete all as specified and directed

M&L for hard core of broken stone of gauge n. exc. 63 mm deposited, spread and leveled in layer n. exc. 15 cm thick water and rammed to a true surfaces etc., complete all as specified and directed.

M&L for TMT bars 6 to 8mm dia and over cut to length bent to shape required including cranking bending spirally for hooping for columns hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia, complete all as specified and directed.

M&L for formwork to sides of concrete foundation, footing, bases of column, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter of flat finished fair surfaces, complete all as specified and directed.

M&L for formwork to soffits of suspended slabs such as roof slab, floor slab, landing and similar work not exc 200mm thick (horizontal or sloping) of flat finished fair surfaces, complete all as specified and directed.

M&L for flat formwork to edges of concrete flats, break in floors, opening in concrete walls, floors and roofs and sides of RCC/PCC bands in walls, horizontal or sloping and similar work all n. exc complete all as specified and directed.

M&L for RCC, M-25 design mix using 20 mm graded crushed stone aggregate as in slabs supported on walls and column in floors , roof landing , balconies canopies deck slabs and in shelves etc., complete all as specified and directed.

M&L for PCC 1:3:6, type C-2, using 40mm graded crushed stone aggregate as in flooring and plinth protection finish even and smooth without using extra cement etc., complete all as specified and directed.

M&L for spike rolling to surfaces or making impression of expanded metal, whilst the concrete is green, complete all as specified and directed.

Excavating in trenches, n exc1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out for soft soil complete all as specified and directed.

M&L for providing plain cement concrete 1:3:6 type C-2 (using 40 mm grade stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M&L for PCC 1:2:4, type B-2, using 20mm graded crushed stone aggregate as in surface channels, benching etc., laid to shape and slope including all formwork etc. complete all as specified and directed.

Extra for forming fair finished drain or channel 45cm inner girth in cement concrete, using extra cement including forms, moulds, mitered/ stopped ends etc. (for saucer drain), complete all as specified and directed.

Taking down carefully point wiring from existing place (light/fan, socket or power points complete) with all fittings such as switches, sockets ceiling rose , pendant holder, fitting and fixtures , MCB, Main switches, call bell etc and making good to disturbed surface to wall ,floor etc to match with existing surface either by using same colour distemper or white colour wash complete all as specified and directed.

Taking down carefully unserviceable main switches and distribution boards with fuses/ MCB's (single phase or three phase) of any capacity complete all as specified and directed.

Taking down carefully old unserviceable sub main wiring including meters and making good disturbed surfaces and matching with existing complete all as directed and specified

M&L for point wiring with 1.5 sqmm, PVC insulated but unsheathed, stranded copper conductor single core FRLS cable, IS-694 marked, drawn through existing metallic/ rigid PVC concealed conduit including replacement of pressed steel terminal mounting box , for mounting fitting like modular switches, sockets, and fixed with brass screws and cup washers including one continuous run of PVC insulated 1.50 sqmm size copper conductor cable green in colour as a earth wire and connected to common earth dolly for One light/ fan/ bell/ Bldg security light point controlled by one single pole one way switch, complete all as specified and directed.

All as per Srl item No. 135.00 above but for one 3 pin, 5 Amp, socket outlet on the same board controlled by one single pole one way switch board complete all as specified and directed.

All as per Srl item No. 135.00 above but for one 3 pin, 5 Amp, socket outlet on the independent board controlled by one single pole one way switch board complete all as specified and directed.

All as per Srl item No. 135.00 above but for wiring with 2.5 sqmm copper cable and 2.5 Sqmm copper cable as continuous earth wire for one 6 pin 6/16 Amps socket outlet on independent board complete all as specified and directed.

All as per Srl item No. 135.00 above but for wiring with 4 sqmm copper cable and 4 Sqmm copper cable as continuous earth wire for one 6 pin 6/16 Amps socket out let on independent board complete all as specified and directed.

S&F modular switch 1 way 6 Amp, 1 module, 240 V flush type complete all as specified and directed.

S & F modular bell push, flush type, 6 Amp, 1 module, 240 V complete all as specified and directed.

S & F modular socket, 6A-2/3 pin combined, 2 module, 240 V complete all as specified and directed.

S & F modular socket, 6Amp / 16Amp-2/3 pin combined, 2 module, 240 V, complete all as specified and directed.

S&F modular switch 1 way 16 Amp, 1 module, 240 V flush type complete all as specified and directed.

S & F modular fan step regulator, 120 W, 2 module, 240 V complete all as specified and directed.

S & F Modular white cover plate with frame including modular metal flush box, 3 module complete all as specified and directed.

S & F Modular white cover plate with frame including modular metal flush box, 6 module complete all as specified and directed.

S & F Modular white cover plate with frame including modular metal flush box, 8 module complete all as specified and directed.

S&F ceiling rose polycarbonate body, 65 x 20 mm three terminal complete all as specified and directed.

S&F for lamp holder pvc body with back plate complete with 9 Watt LED lamp complete all as specified and directed.

S&F Modular RJ telephone socket complete all as specified and directed. Make:- Cat No / SAP code AHLKHWW000 of Havells or equivalent in Legrand/ Schneider.

M&L for telephonic connection with telephone cable GI wire 06/02, 0.50mm dia for one pair telephone up to external wall of bldg PVC insulated, PVC sheathed unarmored and annealed tinned conductor with tape threaded complete all as specified and directed.

Supply and Laying concealed Rigid non-metallic PVC conduit 20mm dia exclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. complete all as specified and directed.

S&F Modular TV Socket complete all as specified and directed. Make: Cat No /SAP code AHLKT0W000 of Havells or equivalent in Legrand/ Schneider.

S&F Cable TV co axial cable complete all as specified and directed.

S&F sheet metal enclosures for MCB distribution board SPN 8 way double door type with 200 amp rated bus bar and suitable for MCB SPN as incomer complete all as specified and directed. Make: Indoasian Cat part No 811807 or equivalent in L&T /Schneider / Seimens /Hager

S&F sheet metal enclosures for MCB distribution board SPN 4 way double door type with 200 amp rated bus bar and suitable for MCB SPN as incomer complete all as specified and directed. Make : Indoasian Cat part No 811805 or equivalent in L&T /Schneider/ Seimens /Hager

S&F MCB SPN, 240 volts, 40 to 63 Amps, rupturing capacity 10 KA, ‘B’ curve type, complete all as specified and directed.

S&F MCB SP 6-32 Amp ,240 V 10 KA B Curve incl all terminals , fittings etc., complete all as specified and directed.

M&L for replacement of call bell electric (ding dong type) , 240 Volt , single pole complete all as specified and directed.

M&L for sub main wiring with two runs of single core 6 Sqmm (nominal area) PVC insulated and unsheathed multi stranded copper conductor cable LT 1100 grade FRLS cable drawn and PVC rigid conduit 20 mm dia with all necessary fittings and accessories and one run of PVC insulated and unsheathed single core cable with copper conductor of size 6 Sqmm as earth wire (green in colour ) run through PVC rigid conduit and connected to common earth dolly , including taking out the old sub main wiring all as specified. Note. Two run of cable and one run of PVC conduit and one run of earth continuity wire shall be measured as one run complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 600 x 600 x 6.0 mm thick buried directly in ground (earth pit not less than 2.25 Mtr normal ground level),and top edge of earth plate not less than 1.5 mtr below normal ground level, connected to galvanised means of earth wire 4 mm dia with bolts, nuts & check nuts, and washers of galvanised iron protection pipe light grade of 20 mm dia and watering pipe medium grade of 20 mm dia and filled with alternate layer of charcoal and common salt, watering funnel with wire mesh, earth pit chamber and cover CI frame PCC 1:3:6 type C-2 all as shown in electrical plate No-3 of SSR part-I of 2009 connected to earthing test point all as specified including all earth work excavation, returning filling and disposal of surplus soil and testing on completion, complete all as specified and directed.

S&F LED light fitting 1x9W/ 1X10W bulkhead luminaries including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed.

S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed.

S&F in replacement LED tube light fitting 4 feet, 1x 20W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified and directed.

S&F Indoor Decorative wall brackets light fixture made up of Polycarbonate, suitable for 9 W LED lamp B22 base with plastic body suitable for 09/11W LED Bulb complete with 9/11 W LED Bulb, complete all as specified and directed.

S&F of LED Bright Lights 6W Picture/ Mirror/ Spot/ Bathroom/ Display/ Wall Flexible Neck Light (White) 2 ft adjustable type energy saving curve type complete all as specified and directed.

Supply, fixing, testing & commissioning of 12/15 Watt Cold white LED Bollard light for Garden lighting, IP 65 protection, prefixed on suitable height pipe, fixed on PCC coping with proper light point connection complete all as specified and directed. Make: Halonix Cat Part No HLOB-02-10-CW or equivalent as approved.

S&F metal clad single pole and a neutral enclosure with a two pin and earth plug and socket with one single pole MCB SP 20 Amp, 240V complete all as specified and directed.

S&F exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm complete all as specified and directed.

S&F in repair LED Bldg Security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection, complete all as specified and directed.

M&L for single phase polycarbonate meter box of suitable size for fixing of existing Single Phase AC Static WH meter / new prepaid meter along with all fixing accessories having IP-65 protection including fixing the box in wall front opening door along with locking system complete all as specified and directed. Note:- (a) Box shall be suitable for IP-65 protection. It shall be made from polycarbonate with glass fiber reinforced material. (b) Degree of protection for mechanical load shall be IK08 as per EN50298. (c) Box should be fire retardant and self extinguishing. It shall have internally embedded extruded silicon gasket. (d) Color code of Box shall be as per Ral 9011/7035. (e) Any make as per specification given can be supplied. (f) Clamp for fixing of Box shall be of SS-304. Screws to be used shall also be of SS-304.

S&F study lamp / table lamp with quality CFL/ LED light bulb and material with conical shade over writing shelf with standard perfect height complete all as specified and directed.

S&F in repair 1100 volts grade heavy duty 6 Sq mm two core service cable PVC insulated aluminium Stranded conductor, served with inner sheathing of PVC sheathed in service connections suspended by insulating hangers and porcelain beat not more than I meter apart including 4Sq mm suspension wire, one twin core cable flat or circular complete all as specified and directed. Make : KEI, Havells and Polycab.

S.R.SHARMA & SONS (BID ID -3507345)