SPL REPAIR TO OTM IN JCOs CLUB SINGLE LIVING ACCN AT J B SUB AREA SIG COY AND PROVN OF 01 X TOILET BLOCK NEAR BLDG NO VIC01 E COY LINE AREA AT BRC DANAPUR UNDER GE DANAPUR CANTT

Taking down cement or lime plaster incl racking out joints hacking for key scrubbing down with water etc.

M&L rendering 15mm thick in two coats(10mm thick base coat and 5mm finishing coat) in cement mortar 1:4 with using water proofing compound on brick work or concrete surfaces and finishing the surface even and smooth. witrhout using extra cement complete all as specified and directed. Note : WPC shall be measured and paid seperately.

M&L rendering 15mm thick in cement mortat 1:6 on brick work or concrete surfaces of walls and finishing the surfaces even and smooth without using extra cement complete.

M&L rendering 10mm thick in cement mortar 1:3 on concrete surfaces of ceiling and finishing the surfaces even and smooth without using extra cement complete.

Supply only integral water proofing compound ISI marked.

M & L for preparation of newly plastered surfaces of wall & concrete and applying 2 mm thick wall care putty including preparation complete.

M&L for applying 2mm thick Birla / JK Putty in two layers on old wall surfaces including complete removal of existing wall finish of any type with wire brush, brooming, dusting and finally washing with water to clean the surface absolutely free from any kind of foreign materials and making good minor cracks etc. and surfaces absolutely even and smooth, rubbing with sand paper complete.

M&L for applying two coats of oil bound distemper on wall or concrete over a coat of primer on prepared surfaces including, rubbing with sand paper complete.

M & L for preparation of newly plastered surfaces of ceiling and applying 2 mm thick wall care putty including preparation of new surface complete.

M&L for applying 2mm thick Birla / JK Putty in two layers on old ceiling surfaces including complete removal of existing wall finish of any type with wire brush, brooming, dusting and finally washing with water to clean the surface absolutely free from any kind of foreign materials and making good minor cracks etc. and surfaces absolutely even and smooth, rubbing with sand paper complete.

M&L for applying two coats of oil bound distemper on ceiling over a coat of primer on prepared surfaces including, rubbing with sand paper complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coat cement base paint over one coat of chalk whitening on plastered surfaces all as specified and directed.

M&L for preparation of old scrapped surfaces of walls of any description by washing, rubbing down and applying two coats of cement base paint complete as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and paving n. exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L 75mm thick PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in plinth protection/ flooring etc finishing even & smooth without using extra cement complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

M&L for 10mm thick Lighft shade vitrified ceramic tiles in floors, area of each tile exceeding 0.36 sqm but not exceeding 0.42 sqm set & jointed in neat cement slurry and pointed in white cement mixed with pigments to match the shade of tiles over and incl 15 mm thick screed bed or bedding layers of cement mortar 1:6 complete all as specified & directed.

M&L for 10mm thick Light shade vitrified tiles on skitting, area of each tile exceeding 0.36 sqm but not exceeding 0.42 sqm set & jointed in neat cement slurry and pointed in white cement mixed with pigments to match the shade of tiles over and incl 10 mm thick rendering in cement mortar 1:4 as backing coat of wall tiles complete all as specified & directed.

M&L coloured non skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match the shade of tiles over and including 15 mm thick screed bed or bedding in cement mortar 1:6 complete all as specified and directed.

M&L for glazed ceramic tiles on vertical surfaces 450 x 300 x7mm thick set and jointed in neat cemet slurry and pointed in white cement mixed with pigments to match the shade of tiles over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed.

Demolition stone slab and tiles of any description or thickness in floors, dado/skirting and apron etc laid bedded and pointed in any mortar complete all as spd and directed.

M & L For Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including 20 mm thick screed bed or bedding layer in cement mortar 1 : 6 complete all as specified and directed.

M & L For Machine cut kota stone slab flooring 20-25mm thick on riser of steps Skitting dado and pillar laid over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including 15 mm thick rendering in cm 1 : 4 as backing coat of wall tile complete all as specified and directed.

M&L PCC 1:2:4 type B0 (using 12.5 mm graded stone aggregate) , 25 mm thick as in sub top layer of floor and finished rough to receive the floor tiles.

Demolition of brick work built in cement mortar complete all as specified and directed.

M&L for brick work using old size sub class 'B' brick straight or curved on plan exceeding 6.00 mtr mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for brick work using old size sub class 'B' brick straight or curved on plan exceeding 6.00 mtr mean radius built in cement mortar 1:4 complete all as specified and directed.

S&F chicken wire mesh on wall fixing with nails for plastering work complete all as specified and directed.

S & F floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring,fixed in floor complete all as directed.

S & F for powder coated aluminium door fame with shutter made out of following section complete fixed to position with hold fast all as specified & directed (a) chowkhat frame of size 83.50 x 44.45 x 1.87 mm thick weight @ 1.30Kg/RM (b) Style/Vertical member of size 47.62 x 44.45 x 1.90 mm thick weightn @ 0.911Kg/RM (c) Top and bottom rail of size 95.25 x 44.45 x 2.00 mm thick weight @ 1.511kg/RM (d) Middle rail of size 49.91x 44.45x 2.01 mm thick weight @ 1.072Kg /RM (e) Top panel with 5.00 mm thick tinted glass fixing with rubber gasket. (f) Bottom panel with 5 to 6 mm thick Alumnium composite panel thick with clips (g) 100 mm dia round handle disc type -02 nos & Alu tower bolt 200mm - 01 No, Hinges 04 Nos each shutter. (h) Aluminum and PVC beading as per requirment as in fixing for paticle board & Glass, joining cleat including locking arrangement. etc

Taking down chowkats with shutters (without taking off shutter from the frame) area not exc 1.5 sqm each complete all as specified and directed.

Taking down chowkats with shutters (without taking off shutter from the frame) area exc 1.5 sqm but n exc 4.0 sqm each complete all as specified and directed.

S&F Pressed steel frames (Factory made) made out of 1.25 mm thick black MS sheet for doors, with one or more rebates including necessary fixing lugs, Butt hinges, lock strike plate, etc complete, size of frame 105x60mm incl bottom of each chowkat to be welded with 2 nos 25x25x3mm thick flat iron projecting 10 cm on either side and back fill to chowkats with PCC 1:3:6 type C 0 using 12.5 mm graded crushed stone aggregate complete all as specified.

Same as item No 33 above but size of frame 125x60mm complete.

S&F Mild steel works as in hold fasts, clamps, plain angle cleats for securing purlins to wood trusses or rafters, cooler stands and similar small articles conforming to Fe 410-0 or Fe 310-0

S&F flush shutter, 35 mm thick, solid core construction with block board core, and ply wood face panels but both face is covered with decorative laminate face veneer with lipping complete all as specified.

S&F in repair 2nd class hard wood 35 mm thick glazed and gauzed skelton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and shutters as specified in SSR Part I, Section 8, clause 8.24 (a)

S&F, in repair 150mm long aluminum anodised barrel tower bolts of extruded section as specified.

S&F, in repair, aluminum alloy anodised sliding door bolts with hasp & staple & fixing clips of sheet cast extruded section & fixing bolts & sliding bolts of extruded section 250mm long.

S&F 150 mm extruded aluminium alloy handles, fabricated type anodised complete all as specified.

Solid PVC door frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening complete all as specified and directed.

S&F factory made solid Panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and gap insert for top and bottom rail; panelling of plain colour PVC sheet 5mm thick to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, complete all as specified and directed.

S&F 75 mm size Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-22 complete all as specified and directed.

S&F 100 mm extruded aluminium alloy handles, fabricated type anodised complete all as specified.

S&F 100 mm Aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F steel windows with side hung shutter incl box type butt hinges with bow handle,steel peg stay, tower bolts ( each shutter having two tower bolts 100mm long ) complete with glazing bars dovetailed or welded complete all as spd and as directed

S&F steel windows with side hung shutter incl box type butt hinges with bow handle,steel peg stay, tower bolts ( each shutter having two tower bolts 100mm long ) complete without glazing bars dovetailed or welded complete all as spd and as directed

S&F steel ventilators with top hung shutters including hinges, steel peg stay complete all as specified and directed.

S&F GI wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with stainless steel wire staple complete all as specified.

S&F in repair GI wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with stainless steel wire staple complete all as specified.

S & F sheet glass 4mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed.

S&F Mild steel framed works such as grills,gratings,etc, with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work for portions framed and hung as gates, including pintle hinges, stops, hand made sliding bolts, etc conforming to Fe 290 Gde -E-165.

Preparing surfaces of new wood and wood based materials of any description and girth, not otherwise described and treated with two coats of synthetic enamel paint over a coat of pink primer.

M & L preparation of new steel surfaces any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red-oxide primer complete.

S&F in repair MS PVC sheathed 20mm dia drapery rod including Bracket ,end ball , rounded block (coated with brown/cherry/Golden colour) of approved pattern and shade complete as approved by GE

S&F in repair water closet white vitreous china ware Orissa pattern of size 580x440mm with integral foot rest ‘P’ or ‘S’ trap front or back inlet incl provision of PCC bedding type B1, 1:2:4 ( 20 mm graded stone aggregate) and connection pipes ( excluding flushing cistern but including flushing pipe 32 mm dia MS chromium plated) (rate also include for taking off unhygienic WC).

S&F in repair 10 Ltr capacity PVC valveless shyphonic action type low level flushing cistern white with inlet, ball valve, float valve and handle incl bracket and flush pipe of low level of 32mm dia fixed to wall complete.

S&F in repair vitreous china WHB size 550x400 mm white flat back including pvc waste pipe but excluding taps, waste, chain & plug & porcelain stopper but including brackets painted with two coats of synthetic enamel painting over a coat of red oxide primer complete all as specified and directed.

S&F in repair 15 mm bore pillar taps cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly-nuts screwed for iron pipe & fixed complete all as specified and directed.

S&F in repair chromium plated overhead shower rose swivel type 125 mm with CP arms 300 mm long complete all as specified and directed.

S&F in repair CP brass tubular towel rail 20 mm dia D type 60 cm long between flanges complete.

S&F in repair of stainless steel soap dish, of standard size and shape complete.

S&F in repair bib tap 15 mm bore, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete.

S&F in repair angle cock 15 mm bore fancy type chromium plated, with capstan head, high pressure, screwed down, screwed for iron pipe or for brass ferrule fixed to iron pipe.

S&F in repair PVC connection 15mm dia size and 450 mm long with 2 Nos check nuts its washers complete all as specified and directed.

S&F 100 mm dia grating doom of stainless steel complete all as specified and directed.

Taking up or down steel tubing 15 mm dia and connections including cleaning for re-fixing or removal to store etc.

Taking up or down steel tubing 20 mm dia and connections including cleaning for re-fixing or removal to store etc.

Supply & laying of 16mm outer dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings and wall / ceiling or laying in floors complete all as specified and directed.

Supply & laying of 20mm outer dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings and wall / ceiling or laying in floors complete all as specified and directed.

Cutting chases in brick walls, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete.

Dismantling of AC/PVC/CI pipes from walls including all type of bends/branch pieces complete all as specified and directed.

M&L PVC (SWR) pipes single socketed in any length with rubber ring joints ,fixed to wall, dia of bore 110 mm complete all as specified and directed.

Same as item No 74 above but 75 mm bore.

S&F PVC (SWR) bends any radius of 75 mm dia

S&F PVC (SWR) bends any radius of 110 mm dia

S&F PVC (SWR) bends any radius provided with access door of 110 mm dia

Dismantling water tanks and removing to store of capacity exc 500 and n exc 1000 ltrs complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tanks in white colour tripple layer (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Pt-I of 1000 Ltr capacity complete all as specified and directed.

S&F Ball valves 20mm dia high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 20mm-210gms) complete all as specified and directed.

M&L PCC 1:2:4, type B-0 (using 12.5 mm graded stone aggregate) as on roof top complete all as specified and directed

M&L for 15 mm thick screed bed in CM 1:4 with water proofing compound @ 200ml /50kg of cement or as per manufacturer's instruction finished surface even and smooth with out using extra cement including taking down of complete existing cement plaster from roof top complete all as specified and directed. (Note : WPC will be measured & paid separately).

M&L for water proofing treatment on non approachable / non accessible roof surface horizontal and vertical surfaces in following sequence through manufacturer / authorized applicator of the manufacturer complete all as specified and directed :- NOTE:- The polymeric water proofing membrane shall be extended upto parapet walls and inserted in walls by cutting groove and making good with cement mortar 1:3 as directed.

Properly cleaning and drying concrete surfaces.

Applying a coat of oxidized bitumen based solvent primer @ 0.3 Kg / sqm.

Applying evenly tack coat of industrial bitumen 85 / 25 grade @ 1.2 Kg / sqm.

Laying unrolled over the bitumen coat surfaces polymeric water proofing membrane, hyperplas standard weight not less than 3 Kg / sqm with 100 mm over laps shall be sealed by flame as per manufacturer instruction.

Applying a coat of aluminium paint @ 100 gm / sqm over and including a coat of hot air blown grade bitumen of grade 85 / 25 @ 1.2 Kg / sqm duly sanded over polymeric membrane complete.

Boring holes 5m deep in soil for Single under reamed piles and getting out and disposal of soil to a distance of n.exc 50m (dia of pile 300mm)

Excavation in trenches, n exc 1.5m wide and n exc 1.5m in depth, for foundation etc and getting out in soft/loose soil.

M&L PCC 1:4:8 type-D2 (using 40mm graded stone aggregate) as in foundations, filling and mass concrete/sub base of floors.

M&L 40mm thick damp proof course to horizontal or vertical surfaces including necessary form work in cement concrete 1:2:4, type B-0.

M&L for hard core of gauge n.exc 63 mm deposited, spread and levelled in layers n.exc 15 cm thick with broken bricks, watered and rammed to a true surface complete all as specified.

M&L reinforced cement concrete (M-25 Design mix) (using 20 mm graded stone aggregate) in foundation, footing, foundation beams, plinth beams, bases for columns, pedestal, under reamed piles, mass concrete, etc complete.

M&L reinforced cement concrete (M-25 Design mix) (using 20mm graded stone aggregate) as in columns, pillars, posts, struts etc complete.

M&L reinforced cement concrete (M-25 Design mix) (using 20mm graded stone aggregate) as in slabs supported on walls, beams and column in floors, roofs, landings, balconies, deck slabs and in shelves and the like complete.

M&L RCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in cantilevers, bressmummers, lintels over 1.5 m span, seismic bands etc complete all as specified and directed.

M&L Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (horizontal or sloping) for flat rough finished surfaces of concrete.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished flat surfaces of concrete.

M&L form work to sides of pillars, posts, struts, piers, columns and stanchions for rough finished , square, rectangular or polygonal surfaces of concrete.

Form work to edges of concrete flats, treads, breaks in floors window cills, concrete railing, openings in concrete walls, floor and roofs n exc 20 cm wide and side of RCC/PCC bands in walls, horizontal or sloping and similar work complete all as specified.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as spd and as directed.

S&F Mild steel TMT bars, 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hoopinbg for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia or securing with clips all as specified

Same as item No 99 above but 6mm dia and over upto and including 10 mm dia in stirrups, spacers and binders

S&F 35mm thick 2nd class hardwood factory made plain framed, panelled shutter (two panel) with lock rail and panel of 9mm B.W.P commercial ply or 12mm veneered particle board with commercial veneering on both faces, size of rail and stile as per IS:1003 (Part-I), Klin seasoned and chemically pressure treated complete all as apecified and directed.

M&L PCC 1:2:4 type B1 (using 20mm graded stone aggregates) as in bed blocks for hold fasts including necessary form works complete all as apecified and directed.

S&F aluminium alloy handles, cast type anodised 125 mm long complete.

S&F, Aluminium hinges (ISI marked), medium weight of size 100 mm complete all as directed

S&F 150mm long aluminum anodised barrel tower bolts of extruded section as specified.

S&F Aluminium handles, cast type, anodized 150 mm size comp ISI Marked

S & F of 150 mm size (Overall length of cover plate) floor door stopper of aluminium body and tongue, anodised, with hard drawn steel spring complete all as specified and directed.

Preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of white wash.

M&L preparing newly plastered surfaces and applying 3 coats of white wash on walls complete all as specified and directed.

M&L for Prepration of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C2 using 40mm graded stone aggregate as in floor/plinth protection laid in suitable panels finished even and fair all as spd . 6mm Joints should be filled with bitumen mastic filling comprising of one part of heated bitumen 85/25 or 80/100 grade and three part of sand ( all by weight)

S&F steel tube medium grade galvanized with all fittings and fixed to walls or laid in floors of 15mm bore including cutting chasing in walls etc

Supply and fixed Vitreous China wash basin white flat back size 450x300 mm including bracket, cutting for and pinning the ends of brackets or erecting stands also including brass chromium plated waste coupling 32mm dia,PVC flexible waste pipe of adequate length and dia and PVC connection 15mm size 450 mm length with brass CP nuts on both sides complete all as apecified and directed.

S&F 15 mm bore pillar taps cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly-nuts screwed for iron pipe & fixed complete.

S&F bib tap 15 mm bore, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete.

S&F 15 mm dia stop valves, cast copper alloy, with iron wheel head, screwed both ends for iron pipe, all as specified

S&F angle cock 15 mm bore fancy type chromium plated, with capstan head, high pressure, screwed down, screwed for iron pipe or for brass ferrule fixed to iron pipe.

S&F water closet white vitreous china ware Orissa pattern of size 580x440mm with integral foot rest ‘P’ or ‘S’ trap front or back inlet incl provision of PCC bedding 1:2:4 type B1 ( using 20 mm graded stone aggregate) and connection pipes ( excluding flushing cistern but including flushing pipe 32 mm dia MS chromium plated) complete.

S&F PVC valve less, syphonic action type flushing cistern of 10 ltr capacity, low level with inlet, ball valve, float and handle including brackets incl PVC connection with CP brass nuts on both sides .

S&F vitreous china urinals bowl type flat back, size 465 x 355 x 265 mm, white , complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement; fixing flush pipe, grating and union for discharge pipe.

S&F CP urinal spreader for fixing with 15 mm bore pipe complete all as specified.

M&L Granite tiles 18-20mm thick machine cut , bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone incl grinding and polishing and incl 15mm thick screed bed CM 1:4 all as specified complete.

S&F 75/100mm bore PVC (SWR) floor trap,plain with grating including jointing to waste pipe complete all as apecified and directed.

Excavating over areas,n exc 1.5 m deep and getting out in soft/loose soil complete all as apecified and directed.

Excavating over areas, exc 1.50m but n exc 3.00m deep and getting out soft/loose soil complete all as apecified and directed.

M&L Rendering 12 mm thick on Fair Faces of brick work or concrete Surfaces in cement mortar 1:3 complete all as apecified and directed.

S & F 200 mm Reinforced Cement Concrete pipes, class NP3, laid and jointed complete with collars complete all as apecified and directed.

M&L150 mm thick PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) as concrete bed to drain pipes including packinng under, and haunching against the sides of pipes after they are laid and tested complete all as apecified and directed.

Taking down carefully aluminium point wiring(any type)for one light point, fan point ,exhaust fan point, bell point, power point complete including all fittings such as switches, socket, pendents holder, ceiling rose, sketch fittings, tube light fittings, regulatores unscrewing the switch sockets, ceiling rose, regulators from boards/outlet boxes and making good the disturbed surfaces of wall/ ceiling and colour washing matching with the existing colour wash all as specified and directed.

M&L for point wiring complete with PVC insulated unsheathed, 1100 volts grade cable 1.5 Sqmm (nominal area) FRLS type multi stranded copper conductor, single core drawn in and including not less than 20 mm dia rigid PVC conduit 'medium grade' ISI marked including all conduit accessories for concealed wiring for one light/fan/ / exhaust fan point controlled by one, one way switch, including concealed pressed steel terminal box of required size not less than 1.0 mm thick factory made duly painted inside & outside with two coats of black bituminous paint over & including a coat of red oxide primer, with 2.8 mm thick top cover of plastic laminated sheet of required colour for mounting switch, sockets, fan regulator etc including 1.5 Sqmm FRLS type PVC insulated unsheathed cable multi-stranded copper conductor as continuous earth wire and connected to earth dolly as required at site& including chases cutting & making good disturbed surface & applying finishes to match existing surface complete all as specified and directed.

Same as item No 131 here-in-before but one 3 pin, 5 Amp socket out let on independent board complete all as specified and directed.

Same as item No 131 here-in before but 3 pin,5 Amp socket out let on the same board with other switch complete all as specified and directed.

Same as item No 131 but for one bell/buzzer point controlled by one bell push single pole one way .

Same as item No 131 above but for one 6 pin 15/16 amps socket outlet point on an independent board with cables of size 2.50 Sqmm.

M&L for point wiring complete with PVC insulated unsheathed, 1100 volts grade cable 4.0 Sqmm (nominal area) FRLS type multi stranded copper conductor, single core drawn in and including not less than 20 mm dia rigid PVC conduit 'medium grade' ISI marked including all conduit accessories for concealed wiring including concealed pressed steel terminal box of required size not less than 1.0 mm thick factory made duly painted inside & outside with two coats of black bituminous paint over & including a coat of red oxide primer, with 2.8 mm thick top cover of plastic laminated sheet of required colour for mounting switch, sockets, fan regulator etc including 4 Sqmm FR type PVC insulated unsheathed cable multi-stranded copper conductor as continuous earth wire and connected to earth dolly as required at site& including chases cutting & making good disturbed surface & applying finishes to match existing surface complete all as specified and directed.

M&L sub main wiring with two single core PVC insulated & unsheathed cable 6.0 Sqmm (nominal area) FRLS type having multi-stranded copper conductor drawn in and including not less than 20 mm dia rigid PVC conduit 'medium grade' ISI marked including all conduit accessories for concealed wiring with and including 6.0 Sqmm FRLS type PVC insulated unsheathed cable multi-stranded copper conductor as earth wire connected to common earth as per IS & cutting chasing for conduit & sinking for boxes & making good to walls disturbed surface & applying finishes to match existing surface complete including taking down of exsting sub main wiring complete all as specified and directed. NOTE : Two runs of 6 Sqmm and one run of 6.0 Sqmm cable and PVC conduit shall be measured as a one unit length.

M&L for sub main wiring with PVC insulated 1100V grade FRLS single core multi stranded copper conductor cable of size 2x4 sqmm + 1x4 sqmm as earth continuity cable passing through and including 25/20mm dia PVC conceal conduit all as specified and directed by Engr-in-Charge. Note - Two runs of 4sqmm including one run of 4 sqmm including PVC conduit shall be measured as unit length.

S & F for switch piano, flush type, 5 amps, single pole, one way, 230 volt complete all as specified and directed.

S & F bell push switch 5 Amp flush type complete all as specified and directed.

S & F for 2/3 pin, 5 Amp/ 6 Amp , socket outlet, flush type, 2 in 1 complete all as specified and directed.

S & F for bell, ding- dong , AC, 230 Volt, single pole complete all as specified and directed.

S&F switch socket combination 2 in 1, 6 pin 16Amps multipurpose type 240 volts complete all as specified and directed.

S&F ceiling rose single phase , PVC poly carbonate,insulated body three terminals ISI marked complete all as specified and directed.

S&F sheet metal enclosure for 4 way TPN DB double door 415 Volt with 200 amp rated bus bar complete with suitable for 1 x 63Amp TPN as incomer and MCB SPN as outgoing connection through proper size of lugs and cable glands including taking down existing MCB DBs complete all as specified and directed.

Supply and fixing 415V 10KA 'C' curve miniature circuit breaker (MCB) of 4 poles and current carrying capacity 63 Amp in the DB complete with connection testing and commissioning.

S& F for sheet metal enclousre factory made for MCB DB's SPN, 12 way, double door, 240 Volts with bus bars including taking down existing unserviceable MCB DB complete make -Havells all as specified and directed.

S&F MCB SP 240 Volt 6 TO 40 Amp ISI marked conforming to 'C" curve, breaking capacity 10 KA complete all as specified and directed.

S&F MCB SPN 40 to 60 amp 30mA for earth leakage. Over load and short circuit protection ISI marked complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25m deep below GL with top edge of plate not less than 1.50 m below normal ground level) connected to galavanised earth lead wire 4.0 mm dia (7.5m) as means of bolts, nuts, check nuts and washer besides brazing at all joints as shown on drawings and including excavation, earth work, GI pipe (ISImark) light grade 15 mm bore for protection of GI wire from earth electrode to and including the earth test point, supplying and laying charcoal dust, common salt, PCC 1:3:6, type C-1(using 20 mm graded crushed stone aggregate ) chamber and mild steel angle iron frame 40 x 40 x 3 mm and 40 mm thick pre-cast RCC cover 1:2:4 , type B-1(using 20 mm graded crushed stone aggregate ) reinforced with 8 mm dia TMT bars @ 75 mm C/C both ways with mild steel handle 12 mm dia, PGI funnel and wire mesh, 20 mm dia GI pipe light grade(ISI marked) for watering all as shown in electrical plate No 3 of SSR Part-I and connected to earth test point including testing of earthing & dismantling /taking down existing old / unserveciable earthing complete all as specified and directed. (Note:- The rates quoted shall also deemed to include the cost of Earth test point and earth wire and protection pipe upto 7.5 meter beyond the earth plates electrode.)

Excavation in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. for laying of cables and getting out in soft/loose soil complete all as specified and directed.

Removal of surplus excavated soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed.

Supplying, laying, jointing & testing cross sectional area 35 Sqmm, 3.5 core XLPE cable insulated armoured, electric power cables (heavy duty) 1100 Volts grade with standard aluminium conductor including taking down existing old /unserveciable cable complete all as specified & directed. Note: Excavation & earth work, sand cushioning & Bricks shall be measured & paid separately under respective items

S &F for 50 mm dia GI pipe 'light grade' ISI marked including fittings such as bends, tees, sockets etc fixed on wall/pole or laid in trenches under road crossing/hardstanding including taking down existing pipe complete all as specified and directed.

M&L Sand cushioning with dry local sand for cable protecting under ground cable (8 cm before laying the cable and 15 cm after laying the cable) in trenches including punning the sand upto 18 cm thick and consolidated complete all as specified and directed. NOTE : Punned thickness only shall be measured for payment purposes.

Supply and laying dry well burnt locally available brick sub class'B' laid flat with width equal to the length of whole bricks over cable as cable protection complete all as spcified and directed

Returning, filling in excavated approved soil, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm each complete all as specified and directed.

S&F five stepped type electronic fan regulator socket type, compatible for BLDC fan AC 230 volt suitable for any type of ceiling fan complete all as specified and directed.

Supply and fixing LED lights fitting 1x 20W, 220V,AC decorative box type Extruded aluminum housing (enhances safety) with high quality polycarbonate diffuser, 4 ft, 2000lm,voltage protection range 140V -270 V,NW 4000K ,connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fixing LED lights fitting 1x 10W, 220V,AC decorative box type Extruded aluminum housing (enhances safety) with high quality polycarbonate diffuser, 2 ft, voltage protection range 140V -270 V,NW ,connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S & F Building security/street LED light fitting 35 watt IP-65 protection pressure diecast alluminium body ,heat resistant glass ,including driver and making necessary electric connection with 2.5 sqmm twin core copper wire 1.5 long complete fixed in and including GI pipe medium grade 40 mm fixed to pole complete all as specified and directed.

Supply, fixing and testing of ceiling fan 1200 mm sweep, heavy duty, single phase, AC, 230 Volts, 50Hz, BEE 5 star rating, ISI marked complete with down rod, canopy, blades, BLDC motor etc and connecting up complete including complete connection from ceiling rose to fan including writing of MES Number with synthetic enamel paint complete all as specified and directed including taking down old unsv one and deposit in MES store for BER.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm complete all as specified.

Supply and fixing switch piano flush button single pole one way 15 Amp 240 volt complete all as specified and directed.

Supply and fixing socket outlet flush type multipurpose 2 in 1, 3 pin 5 and 15 Amp, 240 volts complete all as specified and directed.

Supply and fixing double door SPN DBs eight way of powder coated DB's suitable for MCB's fitted with bus bar,Neutral link,Earth bar and Din rail as per existing finishing complete all as specified and directed.

Supply, laying, jointing and testing cable XLPE Insulated,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sqmm 4 core complete all as specified and directed.

Supply and laying for galvanised iron tubing medium grade with and including all fittings such as bends, elbows, tees, short pieces, union etc in trenches complete all as specified and as directed of following sizes :-.

25 mm (1”) dia.

20 mm (3/4”) dia.

S & F for Gun metal gate valve with iron wheel head screwed both ends ISI marked fixed to GI pipe complete all as specified and as directed of following sizes :-

25 mm (1”) dia

20 mm (3/4”) dia.

M & L for Cutting existing GI/CI water mains 80 mm dia in position for insertion of tee, branch line etc to new water connection complete all as specified and directed.

Please Enable Macros to View BoQ information