HVAC SYSTEM

ANNEXURE-II DEVIATION SHEET (COST OF WITHDRAWAL)

PROJECT:- 3X200+3X500+1x500 MW NTPC KORBA TPP-FGD

PACKAGE :- HVAC FOR FGD

TENDER ENQUIRY :- 77/25/6318/SAN Date 6-Mar-26

NAME OF THE BIDDER

1 TECHNICAL DEVIATION

2 COMMERCIAL DEVIATION

NOTES: 1. Cost of Withdrawal of deviation will be applicable on the basic price (i.e. excluding taxes, duties & freight) only. 2. All the bidders have to list out all their technical & commercial deviations (if any) in details in the above format. 3.Any deviation not mentioned above and shown separately or found hidden in offer, will not be taken cognizance of. 4.Bidder shall submit duly filled unpriced copy of above format indicating "quoted" in "cost of withdrawl of deviation" column of the schedule above along with their Techno-commercial offer, wherever applicable. In absence of same, such deviation(s) shall not be considered and offer shall be considered in total compliance to NIT. 5. Bidder shall furnish price copy of above format along with price bid. 6.The final decision of acceptance/ rejection of the deviations quoted by the bidder shall be at discretion of the Purchaser. 7.Bidders to note that any deviation (technical/commercial) not listed in above and asked after Part-I opening shall not be considered. 8. For deviations w.r.t. Credit Period, Liquidated damages, Firm prices if a bidder chooses not to give any cost of withdrawl of deviation loading as per Annexure-VII of GCC, Rev-07 will apply. For any other deviation mentioned in un-priced copy of this format submitted with Part-I bid but not mentioned in priced copy of this format submitted with Priced bid, the cost of withdrawl of deviation shall be taken as NIL. 9. Any deviation mentioned in priced copy of this format, but not mentioned in the un-priced copy, shall not be accepted. 10. All techno-commercial terms and conditions of NIT shall be deemed to have been accepted by the bidder, other than those listed in unpriced copy of this format. 11. Cost of withdrawl is to be given seperately for each deviation. In no event bidder should club cost of withdrawl of more than one deviation else cost of withdrawl of such deviations which have been clubbed together shall be considered as NIL. 12. In case nature of cost of withdrawl (positive/negative) is not specified it shall be assumed as positive. 13. In case of descrepancy in the nature of impact (positive/ negative), positive will be considered for evaluation and negative for ordering.

NAME OF PROJECT: 3x200MW + 4X500MW KORBA TPP (FGD SYSTEM PACKAGE) Bidder Name

NAME OF PACKAGE: HVAC FOR FGD

TECHNICAL SPECIFICATION No: PE-TS-466-(571-13000-A)-A002 Enquiry No- 77/25/6318/SAN Dated 06.03.2026

Supply Services

S. No. DESCRIPTION UNIT QTY Total Ex-Works Excluding GST (INR) Freight % Freight in INR Total FOR Site Price Excluding GST (INR) Unit Price (INR) Total Price (INR) Total Scope Price

0.0 Total lump sum firm price for Supply part including Mandatory spares and Services comprising of design (i.e. preparation and submission of drawing /documents including “As Built” drawings and O&M manuals), engineering, manufacture, fabrication, assembly, inspection / testing at vendor's & sub-vendor’s works, painting, maintenance tools & tackles, fill of lubricants & consumables along with spares for erection, start-up and commissioning as required, forwarding, proper packing, shipment and delivery at site, unloading, handling, transportation & storage at site, in-site transportation, assembly, erection & commissioning, final painting at site, minor civil work, trial run at site and carrying out Performance guarantee / Functional / Demonstration tests at site (As applicable), training of NTPC/BHEL's O&M staff and handover in flawless condition of the package to the end customer complete with all accessories for the total scope defined as per BHEL NIT & tender technical specification as specified above, amendment & agreements till placement of order. Lot 1

0.0 MAJOR BREAK-UP OF PRICES GIVEN IN 1.0 ABOVE.

2.1 Total lump sum firm price for Supply part comprising of design (i.e. preparation and submission of drawing /documents including “As Built” drawings and O&M manuals), engineering, manufacture, fabrication, assembly, inspection / testing at vendor's & sub-vendor’s works, painting, maintenance tools & tackles (as per Appendix-A), fill of lubricants & consumables along with spares for erection (as per Appendix-B), start-up and commissioning spares as required, forwarding, proper packing, shipment and delivery at site for the total scope defined as per BHEL NIT & tender technical specification as specified above, amendment & agreements till placement of order. (Break-up as per Annexure-I) Lot 1 _ * #,##0.89_ ;_ * \-#,##0.89_ ;_ * "-"??_ ;_ @_

2.2 Total lumpsum firm prices for Services comprising of service part for unloading, handling, transportation & storage at site, in-site transportation, assembly, erection & commissioning, final painting at site, minor civil work, trial run at site and carrying out Performance guarantee / Functional / Demonstration tests at site (As applicable), Training of NTPC/BHEL personnel for total 15 days (in 3-4 parts of 4-5 days each) covering hands on experience of operation and maintenance of air conditioning and ventilation system. Site personnel shall be trained for operation and maintenance activities covering daily, weekly, monthly, quarterly and yearly maintenance checks and handover in flawless condition of the package to the end customer complete with all accessories for the total scope defined as per BHEL NIT & tender technical specification as specified above, amendment & agreements till placement of order. (Break-up as per Annexure-I) Lot 1 5195237.978095981 _ * #,##0.21_ ;_ * \-#,##0.21_ ;_ * "-"??_ ;_ @_

2.3 Total lumpsum firm price for mandatory spares comprising of manufacture, fabrication, assembly, inspection / testing (as applicable) at vendor's & sub-vendor’s works, painting, forwarding, proper packing, shipment, delivery at site & guarantee as per tender technical specification above, amendment & agreements till placement of order. (Break up of mandatory spares is to be furnished as per Annexure- II) Lot 1 _ * #,##0.14_ ;_ * \-#,##0.14_ ;_ * "-"??_ ;_ @_

2.4 Total lumpsum firm price for providing Operation and Maintenance Service (24x7) including manpower, supervision, consumables etc. for operation & maintenance after commissioning of Air Conditioning system before final handing over to end customer in flawless condition for the scope defined as per technical specification for Air Conditioning system Months 6 20175681.468333904 _ * #,##0.48_ ;_ * \-#,##0.48_ ;_ * "-"??_ ;_ @_

Note: 1) For detailed scope of Operation and Maintenance Services of Air Conditioning system, Technical Specification to be referred. Any variation in no. of months shall be exercised based on unit rate arrived from price quoted against Sl.no 2.4 above.

NAME OF PROJECT: 3x200MW + 4X500MW KORBA TPP (FGD SYSTEM PACKAGE)

NAME OF PACKAGE: HVAC FOR FGD

TECHNICAL SPECIFICATION No: PE-TS-466-(571-13000-A)-A002

SL NO DESCRIPTION Qty UNIT SUPPLY ERECTION AND COMMISIONING

Unit Ex-Works Price (INR) Total Ex-Works Price (INR) Unit Price (INR) Total Price (INR)

1a* DX type, air cooled condensing unit of minimum 50 TR (ACTUAL) capacity. The refrigerant compressor shall be Scroll, hermetic / Semi-hermetic type suitable for Refrigerant R-134a / R-407c / R-410a environment friendly HFC refrigerants with drive package, Suction and discharge valves, capacity control system, expansion valve, crank case heater etc. A control panel shall be provided to house all gauges and controls. The panel shall contain all necessary terminal strips to facilitate external wiring. The unit shall be complete with expansion valve, all necessary fittings, accessories, insulated refrigerant piping to and from AHUs, foundation bolts, nuts, washers etc complete in all respect. 6 Nos

1b1* Sheet metal cabinet type air handling units (double skin as per specification) The draw through horizontal AHUs (min. 60 mmWC SP) shall comprise of Dampers, pre filter, fine filters, DX- cooling coil, Fan section with fan & TEFC sq cage induction motor, condensate drain pan, thermostatic controls and other accessories, like ladder along with supporting structure for filter and plenum, etc. to meet the AC load of control room area as per specification. Capacity :22000 CFM/37400 CMH @ 65 mm WG static pressure (Erection & Commissioning Only) 6 Nos

1b2* 37 KW Motor for the Air Handling Units 6 Nos

1c* Monsoon reheating / winter heating kit comprising strip heaters, safety controls, air-stat, contactors, frame work, thermostat etc. Capacity :6.9 KW- 1 No. & 3.3 KW 1 No. 2 Nos

1d* Pan type humidifier, comprising geyser stat, for each AHU room. Capacity :10 KW- 1 No. (Erection & Commissioning Only) 1 Nos

1e* Fresh air fan (axial flow type), complete with motor, inlet cone, air filters (pre and fine), dampers etc. (Capacity :3300 cfm- 1W+1S 2 Nos

2a* Thermal insulation of supply air duct & return air duct with finish as specified. (Erection & Commissioning Only) 630 SQM

2b* Thermal insulation of supply air duct & return air duct with finish as specified. 100 SQM*

3* MS medium class drain piping upto nearest drain point with insulation & cladded and without insulation

a* 50mm with insulation and cladding 20 Rmt*

b* 40mm with insulation and cladding 20 Rmt*

c* 50mm without insulation and cladding 20 Rmt*

d* 40mm without insulation and cladding 20 Rmt*

4* Air-cooled split type AC units consisting of condensing unit & evaporating unit including refrigerant pipes & fittings with insulation etc.

(a)* 2.0 TR capacity (non-ductable type, 240 V, 1 phase ) with isolation switch , i.e MCB of suitable rating as specified, voltage stabilizer, cabling, all supporting structure and refrigerant piping to suite actual site condition. 14 Nos*

B VENTILATION SYSTEM

1a* Modular type Unitary air filtration unit with centrifugal fan with motor, pumps with motors, filters, UAF internals, inlet air louvers, piping as per IS: 1239 pt I (heavy class galvanised), valves, nozzles, back wash arrangement, galvanised drain piping etc. as per specification of capacity total 1,20,000 CMH . Each UAF has 1 no centrifugal fan (1 x 100% duty) of capacity 1,20,000 CMH at min. 60 mmWC SP. 2 Nos*

2a* Thermal insulation along with finish as per specification for supply air duct (Erection & Commisioning only) 370 SQM*

2b* Thermal insulation along with finish as per specification for supply air duct 100 SQM*

3* Roof extractor units (axial flow type) with hood, disconnect switch and all accessories as specified. Following fan shall have 15 mmwc static pressure.

a)* Capacity 40,000 CMH with Motor rating 5.5 KW 4 Nos.*

4* Axial flow supply fans with pre and fine filter (wall mounted) complete with casing, TEFC sq cage induction motors & mounting frame, MS rain protection cowl, bird screen along with support structure and all other accessories (suitable for 415V/3-phase supply). Following fan shall have 30 mmwc static pressure.

a)* Capacity 10,000 CMH with Motor rating 2.2 KW 5 Nos.*

c)* Capacity 6,000 CMH with Motor rating 1.1 KW 10 Nos.*

d)* Capacity 4,000 CMH with Motor rating 0.75 KW 1 Nos.*

5* Axial flow supply fans with pre filter (wall mounted) complete with casing, TEFC sq cage induction motors & mounting frame, MS rain protection cowl, bird screen along with support structure and all other accessories (suitable for 415V/3-phase supply) as specified. Following fan shall have 20 mmwc static pressure.

a)* Capacity 10,000 CMH with Motor rating 1.5 KW 33 Nos.*

c)* Capacity 6,000 CMH with Motor rating 1.1 KW 1 Nos.*

6* Axial flow exhaust fans (Bifurcated type, spark proof construction, wall mounted) complete with casing, flame proof motor & mounting frame, MS rain protection cowl, bird screen along with support structure and all other accessories epoxy painted (suitable for 415V/3-phase supply) as specified. Following fan shall have 15 mmwc static pressure.

b)* Capacity 7,500 CMH with Motor rating 1.1 KW 4 Nos*

d)* Capacity 2,000 CMH with Motor rating 0.55 KW 2 Nos*

7* Axial flow exhaust fans (Wall mounted) complete with casing,TEFC sq cage induction motor & mounting frame, MS rain protection cowl, bird screen along with support structure and all other accessories epoxy painted (suitable for 415V/3-phase supply) as specified. Following fan shall have 10 mmwc static pressure.

a)* Capacity 15,000 CMH with Motor rating 1.1 KW 1 Nos.*

b)* Capacity 10,000 CMH with Motor rating 0.75 KW 2 Nos.*

c)* Capacity 7,500 CMH with Motor rating 0.55 KW 0 Nos.*

d)* Capacity 6,000 CMH with Motor rating 0.55 KW 2 Nos.*

e)* Capacity 4,000 CMH with Motor rating 0.55 KW 1 Nos.*

f)* Capacity 2,000 CMH with Motor rating 0.37 KW 0 Nos.*

8* Exhaust fan (propeller type) completes with induction motor & mounting frame MS rain protection cowl, bird screen and all other accessories as specified (suitable for 240V/ 1 phase). Following fan shall have 5 mmwc static pressure.

a)* Capacity 1000 CMH with Motor rating 100 watts 12 Nos.*

C COMMON FOR AC AND VENTILATION SYSTEM

1* Supply air ducting (finished) for above area complete with dampers, grills (with VCD & without VCD), supports (painted) and all accessories as specified.

1.1* Finished (Actual quantity of duct erected at site, excluding the scrap) GSS (zinc coating 275 gms/sq.m) Ducting with support structure etc.

a)* 18 G (Erection & Commissioning only) 250 SQM*

c)* 20 G (Erection & Commissioning only) 340 SQM*

e)* 22 G (Erection & Commissioning only) 1450 SQM*

f)* 22G 100 SQM*

g)* 24 G(Erection & Commissioning only) 160 SQM*

h)* 24G 100 SQM*

1.2a* Supply air Grill/diffuser with VCD (Extruded Aluminium) (Erection & Commissioning). 20 SQM*

1.2b* Supply air Grill/diffuser with VCD (Extruded Aluminium). 10 SQM*

1.3a* Return air Grill/diffuser without VCD (Extruded Aluminium). (Erection & Commissioning). 20 SQM*

1.3b* Return air Grill/diffuser without VCD (Extruded Aluminium). 10 SQM*

1.4a* Supply air Grill/diffuser with VCD (MS, POWDER COATED) (Erection & Commissioning). 28 SQM*

1.4b* Supply air Grill/diffuser with VCD (MS, POWDER COATED) 10 SQM*

1.5a* Volume control damper in GI construction as per specification (Erection & Commissioning). 40 SQM*

1.5b* Volume control damper in GI construction as per specification 10 SQM*

1.6* Wall mounted dampers (gravity operated) for different areas. 19 SQM*

1.7* Inlet Louvres 4.25 SQM*

2a* ACOUSTIC INSULATION (AS PER THE SPECIFICATION)(Erection & Commissioning). 290 SQM*

2b* ACOUSTIC INSULATION (AS PER THE SPECIFICATION) 100 SQM*

3* FIRE DAMPER 15 SQM*

4a)* Motorized Actuator with single phase power supply for the above Fire damper and Volume control damper with auto resetting, limit switches, indication lamps etc. 15 Nos*

4b)* Motorized Actuator with single phase power supply for the above Fire damper and Volume control damper with auto resetting, limit switches, indication lamps etc. 5 Nos*

5 Cable tray, conduits, junction box, lugs and glands, Local control panel and Field instruments like pressure gauge, temperature gauge, switches and transmitters for pressure, flow and temperature measurement, differential pressure switch across filters, flow meters, RH and Temperature sensor and other required instruments as per specifications, including necessary control panel form hook up with main DDCMIS as per specifications 1 LOT

5.1 Instruments

a)* T‐RH Sensor 2 Nos*

b)* Differential Pressure Switch - Air 6 Nos*

c)* Pressure Switch - Air 6 Nos*

d)* Air Stat 1 Nos*

e)* Level Transmitter 2 Nos*

f)* Pressure Transmitter 2 Nos*

g)* Pressure Gauge 4 Nos*

h)* Temperature Gauge 2 Nos*

i)* Differential Pressure Switch - Water 2 Nos*

j)* Limit Switch 2 Nos*

5.2 Cable Tray for Cable Routing

a)* 100mm Wide, 100mm Depth 50 MTR*

b)* 50mm Wide, 100mm Depth 50 MTR*

6.3 Lugs & Glands 1 Lot

6.4 Junction Box

a)* 128 Ways 2 Nos.

b)* 64 Ways 2 Nos.

6* Providing full support during FAT of DDCMIS, preparation of control scheme, and commissioning of DDCMIS as per relevant specification. 20 Mandays*

7 Total lumpsum price for special tools & tackles for maintenance inclusive of packing forwarding, transportation up to site, etc. (Break up of to be furnished as per Appendix- A) 1 LOT

8 Total lumpsum price for commissioning spares inclusive of packing forwarding, transportation up to site, etc. (Break up of to be furnished as per Appendix- B) 1 LOT

1 The bidder shall furnish unit rates for variable item (marked *) for necessary adjustment (plus or minus) variation during execution. The unit rates quoted above shall be considered and no separate unit rates shall be quoted. Unit rates shall be valid throughout the contract.

2 Bidder to note that above BOQ for this tender has to be read in conjunction with tender specification. Any item, if not mentioned in above BOQ but indicated in tender specification and required for completion of the system shall deemed to be included in above price.

LIST OF MANDATORY SPARES

NAME OF PROJECT: 3x200MW + 4X500MW KORBA TPP (FGD SYSTEM PACKAGE)

NAME OF PACKAGE: HVAC FOR FGD

TECHNICAL SPECIFICATION: PE-TS-466-(571-13000-A)-A002

Sl. No. ITEM DESCRIPTION UNIT QTY. Total Ex-Works Price (INR)

AIR CONDITINING AND VENTIALTION SYSTEM

1 Air handling unit (for each model)

1.1 V-belts for AHU Blower Sets 2

1.2 AHU Blower bearing Sets 1

1.3 Blower motor bearing Sets 1

1.4 Filters at suction and discharge of all AHUs Nos. 25% of installed population

2 Unitary air filtration unit

2.1 Supply Air fans

2.1.1 V-belts for supply air fans Sets 2

2.1.2 Supply air fan bearings Sets 1

2.2.1 Pump bearings Sets 1

2.2.2 Impeller for pump Nos. 1

2.2.3 Pump Shaft Nos 1

2.2.4 Shaft sleeves Sets 1

2.2.5 Gland Packings for pumps Sets 1

2.2.6 Nylon Filter Sets 1

2.2.7 Spray nozzles Nos. 5% of total population or 50 Numbers whichever is higher.

2.2.8 Water strainer Nos. 1

2.2.9 Brass suction screen/strainer for unitary air filtration tank. Sets 1

2.2.10 Motor for Centrifugal fan for UAF Nos. 1

3 Control & Instrumentation

i) Air-Conditioning System

3.1 Electronic Transmitters

3.1.1 Transmitters of all types and model no. (for the measurement of Pressure, differential pressure flow, level, temperature etc.) Nos. 5% or 1 No. of each type and model whichever is more. (to be divided into various ranges in proportion to main population)

3.2 Temperature elements

3.2.1 RTD's* Nos. 5% or 1 No. which ever is more **

3.2.2 Thermo well* Nos. 5% or 1 No. which ever is more ** ** (to be divided into various insertion lengths in proportion to main population)

3.3 All types of Local Indicators Nos. 5% or 1 No. of each make, model and type whichever is more (to be divided to various ranges in proportion to main population of all make, model and type)

3.4 Process Actuated Switch Devices Includes all types of Pressure, differential pressure, flow, and temperature, and differential temperature, level switch Devices. Nos. 5% or 1No. Of each type and model whichever is more.

3.5 Relative Humidity Sensors Nos. 1

3.6 Geyser stat Nos. 1

3.7 Local Humidity/Temperature indicators Nos. 2Nos. each.

4 Process Connection Piping (for Impulse Piping / Tubing, Sampling Piping / Tubing and Air Supply Piping as Applicable)

4.1 Valves Nos. 10% or 1 No. of each type, class, size and model whichever is more.

4.2 2 way, 3way, 5way valve manifolds Nos. 10% or 1 No. of each type, class, size and model whichever is more.

4.3 Fittings Nos. 10% or 1 No. of each type, class, size and model whichever is more.

(II) Ventilation System

5 Measuring Instruments

5.1 Pressure Gauge Nos. 1 No. (for centrifugal pumps of UAF units).

5.2 Level transmitter Nos. 1 No.

5.3 Pressure transmitter Nos. 1 No. (for UAF units)

6 Process Connection Piping (for Impulse Piping / Tubing, Sampling Piping / Tubing and Air Supply Piping as Applicable)

6.1 Valves Nos. 1 no. of each type, class, size and model

6.2 2 way valve manifold Nos. 1 no. of each type, class, size and model

6.3 Fittings Nos. 1 no. of each type, class, size and model

2 A ‘set’ means items or sub-items required for each type/size range of the assembly/ sub-assembly, required for replacement in one main equipment. It is further intended that the assembly/ sub-assembly which have different orientation (like left hand or right hand, top or bottom), different direction of rotation or mirror image positioning or any other reasons which result in maintaining two different sets of the spares to be used for the subject assembly/ sub-assembly, these shall be considered as different types of assembly/ sub-assembly.

3 All mandatory spares shall be supplied as per the requirement of the tender specifications. In case spares indicated in the list are not applicable to the particular design offered by the bidder, the bidder should offer spares applicable to offered design with quantities generally in line with the approach followed in the above list, without any commercial implication.

4 Whenever the quantities have been indicated for each type, size, thickness, material, radius, range etc., these shall cover all the items supplied and installed

5 Wherever rubber part viz: coupling, V belt, flexible hose etc. have been used ,minimum quantity as specified above is to be supplied and any item which is not covered above minimum 10% or 01 no whichever is higher is to be supplied.

6 Wherever non-metallic fabric/paper filter etc. have been used ,minimum quantity as specified above is to be supplied and any item which is not covered above minimum 10% or 01 no whichever is higher is to be supplied

7 Wherever quantity has been specified as percentage (%), the quantity of mandatory spares to be provided by contractor shall be the specified percentage (%) of the total population of the plant. In case the quality so calculated happens to be a fraction, the same shall be rounded off to next higher whole number.

8 Bidder to write “Quoted / Not Applicable” against all items. Any item which is quoted as “not applicable” by the bidder in the above list and is found to be “applicable” at a later date shall be supplied by the bidder without any commercial and delivery implication.

9 Any special tool required for maintenance of any of the equipment being supplied is to be included in mandatory T&P along with the equipment.

10 Any cell left blank in the unpriced schedule shall be treated as “Quoted” and is included in total price.

11 * With head assembly, terminal block and nipple

12 ** to be divided into various insertion lengths in proportion to main population

Maintenance tools & tackles

NAME OF PROJECT: 3x200MW + 4X500MW KORBA TPP (FGD SYSTEM PACKAGE)

NAME OF PACKAGE: HVAC FOR FGD

TECHNICAL SPECIFICATION No: PE-TS-466-(571-13000-A)-A002

SL NO DESCRIPTION UNIT Qty Unit Ex-Works Price (INR) Total Ex-Works Price (INR)

1 FLAT D WRENCH - 6 MM TO 32 MM (12 Pcs) SET 1

2 BOX WRENCHES - 6 MM TO 22 MM (14 Pcs) SET 1

3 RING SPANNER - 6 MM TO 32 MM (12 Pcs) SET 1

4 ALLEN KEYS - 2 MM TO 10 MM SET 1

5 CRESCENT SCREW SPANNER NO. 1

6 SCREW DRIVER NO. 1

7 OFFSET SCREW DRIVER NO. 1

8 INSULATED PLIER NO. 1

9 TORCH LIGHT ( SUITABLE FOR 2 CELL) NO. 1

10 HAMMER 1 LB NO. 1

11 OIL CAN NO. 1

12 POCKET THERMOMETER - 0 TO 50 DEG. C NO. 1

13 INSULATION TAPE ROLL NO. 1

14 STEEL FOOT RULE - 12" NO. 1

15 FEELER GAUGE 9 BLADES NO. 1

16 PIPE WRENCH NO. 1

17 FLARE NUT (1/4") NOS. 6

18 FLARING TOOL NO. 1

19 TUBE CUTTER NO. 1

20 GAS CHARGING PIPE NO. 1

21 NITROGEN CHARGING ADAPTER NO. 1

22 PRESSURE GAUGE (2 1/2" DIA DIAL) 0 - 300 PSI NO. 1

23 PRESSURE GAUGE (2 1/2" DIA DIAL) 0 - 500 PSI NO. 1

24 COMPOUND GAUGE (2 1/2" DIA DIAL) (-)30” to 150 PSI NO. 1

25 PSYCHRO METER NO. 1

26 LOCK WITH KEY FOR TOOL BOX NO. 1

27 RATCHET 1/4" NO. 1

28 MS TOOL BOX NO. 1

29 Measuring tape NO 1

30 Tachometer NO 1

31 Double ended spanner SET 1

32 Gasket punch NO. 1

33 Centre punch NO. 1

34 Scissors for sheet metal cutting NO. 1

35 Multimeter NO. 1

36 Anemometer NO. 1

37 Slide wrench 8” NO. 1

38 Slide wrench 10” NO. 1

39 Slide wrench 6” NO. 1

40 Box spanner set SET 1

1 ABOVE IS THE MINIMUM LIST. ANY OTHER TOOL / TACKEL REQUIRED FOR THE SYSTEM SHALL ALSO BE PROVIDED BY THE VENDOR WITHOUT ANY COST IMPLICATION.

Commissioning spares

NAME OF PROJECT: 3x200MW + 4X500MW KORBA TPP (FGD SYSTEM PACKAGE)

NAME OF PACKAGE: HVAC FOR FGD

TECHNICAL SPECIFICATION No: PE-TS-466-(571-13000-A)-A002

SL NO DESCRIPTION UNIT Qty Unit Ex-Works Price (INR) Total Ex-Works Price (INR)

1 FAN BELTS SET 1

2 PRESSURE GAUGE NO. 1

3 TEMPERATURE GAUGE NO. 1

5 COMPRESSOR OIL Lot 1

6 REFRIGERANT Lot 1

7 LUBRICANT (EACH TYPE) Lot 1

1 ABOVE IS THE MINIMUM LIST. ANY OTHER COMMISSIONING SPARE REQUIRED FOR THE SYSTEM SHALL ALSO BE PROVIDED BY THE VENDOR WITHOUT ANY COST IMPLICATION.