Loading
Loading…
Loading…
Tender Value
₹3.2 Cr
EMD Value
₹6.5 L
Closing Date
31 Aug 2026, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
Above/Below/Par
POWER
15 conditions · 3 needing a document upload
Only those firms which in their individual capacity, satisfy Standard Financial Criteria(s) need to quote for this tender. :The tenderer must have minimum average annual contractual turnover of V / N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-15, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet. The tenderers shall submit Certificates to this effect which may be an attested Certificate from the concerned department / client and/or Audited Balance Sheet duly certified by the Chartered Accountant etc.
The tenderer should have a valid Electrical Contractor License from the concerned statutory authority. The above said Electrical Contractor License is to be submitted along with the offer otherwise the offer shall be summarily rejected.
Defination of Similar Work :- Wiring/Rewiring in buildings with associated electrical works. OR Lighting arrangement in buildings, circulating area, yard, street etc. with associated electrical works. OR Wiring/Rewiring, Lighting arrangement in buildings with associated electrical works.
As a proof of Technical Eligibility, the Tenderer(s) have to submit details (Technical Eligibility) as per Annexure-13 Tender Document, indicating that Contractor have completed any of the following during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: Three similar works costing not less than the amount equal to 30% of advertised value of the tender, or Two similar works costing not less than the amount equal to 40% of advertised value of the tender, or One similar work costing not less than the amount equal to 60% of advertised value of the tender. Format of completion certificate to be produced is provided as annexure-18 of tender docuemnts. Work experience certificate from private individual shall not be considered. However, in addition to work experience certificate issued by any Govt. Organization, work experience certificate issue by Public listed company having average annual turnover of Rs. 500 crore and above in last 3 financial years excluding the current financial year, listed on National Stock Exchange or Bombay Stock Exchange, incorporated /registered at least 5 years prior to the date of opening of tender, shall also be considered provided the work experience certificate has been issued by a person authorized by the Public listed company to issue such certificates. In case tenderer submits work experience certificate issued by public listed company, the tenderer shall also submit along with work experience certificate, the relevant copy of work order, bill of quantities, bill wise details of payment received duly certified by Chartered Accountant, TDS certificates for all payments received and copy of final/last bill paid by company in support of above work experience certificate.
29 conditions · 6 needing a document upload
GSTIN number: Bidder shall submit attested or self attested copy of GSTIN certificate.
Following documents shall be submitted by the tenderer: (A)SOLE PROPRIETOR SHIP FIRM: (i)All other documents in terms of clause 1.1.12 of tender document . (B)HUF: (i) A copy of notarized affidavit on Stamp Paper declaring that he who is submitting the tender on behalf of HUF is in the position of 'Karta' of Hindu Undivided Family (HUF) and he has the authority, power and consent given by other members to act on behalf of HUF. (ii)All other documents in terms of clause 1.1.12 of tender document. (C)PARTNERSHIP FIRM:(i)A notarised copy of the Partnership Deed or a copy of the Partnership deed registered with the Registrar. (ii)A notarised or registered copy of Power of Attorney in favour of the individual to tender for the work, sign the agreement etc. and create liability against the firm.(iii)An undertaking by all partners of the partnership firm that they are not blacklisted or debarred by Railways or any other Ministry / Department of the Govt. of India from participation in tenders / contracts as on the date of submission of bids, either in their individual capacity or in any firm/LLP in which they were / are partners/members. Any Concealment / wrong information in regard to above shall make the bid ineligible or the contract shall be determined under Clause 62 of the Standard General Conditions of Contract.(iv)All other documents in terms of clause 1.1.12 of tender document . (D)JOINT VENTURE (JV): APPLICABLE ONLY FOR WORKS COSTING MORE THAN Rs.10.00 Cr. Not applicable for this tender. (E)Company registered under Companies Act- 2013:(i)The copies of MOA (Memorandum of Association) / AOA (Articles of Association) of the company.(ii)A copy of Certificate of Incorporation.(iii)A copy of Authorization / Power of Attorney issued by the Company (backed by the resolution of Board of Directors) in favour of the individual to sign the tender on behalf of the company and create liability against the company.(iv)All other documents in terms of clause 1.1.12 of tender document. (F)LLP (Limited Liability Partnership) Firm under LLP Act-2008: (i)A copy of LLP Agreement.(ii)A copy of Certificate of Incorporation.(iii)A copy of Power of Attorney / Authorization issued by the LLP in favour of the individual to sign the tender on behalf of the LLP and create liability against the LLP.(iv)An undertaking by all partners of the LLP that they are not blacklisted or debarred by Railways or any other Ministry / Department of the Govt. of India from participation in tenders / contracts as on the date of submission of bids, either in their individual capacity or in any firm/LLP or JV in which they were / are partners/members. Concealment / wrong information in regard to above shall make the contract liable for determination under Clause 62 of the Standard General Conditions of Contract. (G)Registered Society & Registered Trust: The tenderer shall submit: (i)A copy of the Certificate of Registration.(ii)A copy of Memorandum of Association of Society/Trust Deed.(iii)A copy of Power of Attorney in favour of the individual to sign the tender documents and create liability against the Society/Trust.(iv)A copy of Rules & Regulations of the Society.(v)All other documents in terms of clause 1.1.12 of tender document .
The tenderer shall submit a copy of certificate (Annexure 19(A)) in case of other than Company/Proprietary firm by each member of a Partnership Firm / Joint Venture (JV) / Hindu Undivided Family (HUF / Limited Liability Partnership (LLP) etc, as the case may be. Non submission of above certificate(s) by the bidder shall result in summarily rejection of his/their bid. It shall be mandatory incumbent upon the tenderer to identify, state and submit the supporting documents duly self attested/digitally signed by which they/he is qualifying the Qualifying Criteria mentioned in the Tender Document. Note:- As per railway board letter No. 2022/CE-I/CT/GCC Correspondence Dated: 14.05.2024 "On IREPS Module, a facility has already been created for online submission of Annexure-V. Therefore, the provision of downloading of Annexure-V of GCC & uploading of physically signed Annexure-V by the tenderer had been discontinued on IREPS".
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Payment of Bid-security in respect of E- tendering will be deposited either in cash through e payment gateway or submitted as Bank Guarantee bond from a scheduled commercial bank of India or as mentioned in tender documents. The Bank Guarantee bond shall be as per Annexure-VIA of GCC Works 2022(Annexure-21 of tender document) and shall be valid for a period of 90 days beyond the bid validity period and any offer without the same will be treated as invalid. Details of bank account no. and technical details have been provided for in the software (IREPS) to which prospective registered tenderers will have access at the time of tendering.
In case, submission of Bid Security in the form of Bank Guarantee, following shall be ensured: (i) A scanned copy of the Bank Guarantee shall be uploaded on e-Procurement Portal (IREPS) while applying to the tender. (ii) The original Bank Guarantee should be delivered in person to the official nominated as indicated in the tender document before closing date for submission of bids (i.e. excluding the last date of submission of bids). (iii) Non submission of scanned copy of Bank Guarantee with the bid on e-tendering portal (IREPS) and/or non submission of original Bank Guarantee within the specified period shall lead to summary rejection of bid. (iv) The Tender Security shall remain valid for a period of 90 days beyond the validity period for the Tender. (v) The details of the BG, physically submitted should match with the details available in the scanned copy and the data entered during bid submission time, failing which the bid will be rejected. (vi) The Bank Guarantee shall be placed in an envelope, which shall be sealed. The envelope shall clearly bear the identification "Bid for the ***** Project" and shall clearly indicate the name and address of the Bidder. In addition, the Bid Due Date should be indicated on the right hand top corner of the envelope. (vii) The envelope shall be addressed to the officer and address as mentioned in the tender document. (viii)If the envelope is not sealed and marked as instructed above, the Authority assumes no responsibility for the misplacement or premature opening of the contents of the Bid submitted and consequent losses, if any, suffered by the Bidder. (ix) BG/EMD shall be made in the favor of Sr Divisional Finance Manager/FZR.
1. Only firm recognized by department of industrial policy and promotion (DIPP) as "Startups" shall be exempted from payment 4.1.1 of Bid Security as per GCC 2022. 2. All other firms except described above shall be required to submit the Bid Security as per terms and conditions of tender.
PAN CERTIFICATE : PAN The tenderer shall submit the photocopy of Permanent Account Number (PAN) issued by Income Tax authority attested by Gazetted officer / self attested.
The tenderer shall study the Northern Railway General Conditions of Contract Regulations for Tenders & Contracts - 2022 or latest along with tender documents before submission of the tender.
Applicable charges/recoveries/Advance etc. (Deployment of Technical supervisors per attached Annexure XIII) is applicable.
There is an option of payment to contractor through a letter of credit (LC) arrangement (Authority Railway Board's letter no. 2018/CE-I/CT/9 dated 04.06.2018)as given in clause 1.3.14 of tender document.
GCC works 2022(or latest if any) should be the integral part of this tender.
Electrical works in c/w balance works for Civil, Electrical and S&T of 08 nos. of Amrit Bharat Scheme Stations (Dhandari Kalan, Hoshiarpur, Kapurthala, Phillaur, Phagwara, Firozpur Cantt, Moga and Fazilka) over Firozpur Division.
251-Elect-T-05-2026-27~NR
251-Elect-T-05-2026-27
Open
Works - General
6 Months
Firozpur, Punjab
₹0
₹6.5 L
31 Aug 2026
7 Aug 2026
17 Aug 2026
103 items across 1 schedule
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 3,22,82,427.01 | ||
| — | 50.00 | — | — | ||
| Supply and Erection of modular metal boxes concealed boards with white finish single mounting plate and fixing of switches/plug socket and connection wiring. Make Legrand (Myrius), Schneider (Zencelo), Anchor (Ave). Metal boxes boards are to be concealed in the wall for 12 Module | — | — | — | 23,752 | |
| — | 50.00 | — | — | ||
| Supply and Erection of modular metal boxes concealed boards with white finish single mounting plate and fixing of switches/plug socket and connection wiring. Make Legrand (Myrius), Schneider (Zencelo), Anchor (Ave). Metal boxes boards are to be concealed in the wall for 8 Module | — | — | — | 21,228.5 | |
| — | 50.00 | — | — | ||
| Supply and Erection of modular metal boxes concealed boards with white finish single mounting plate and fixing of switches/plug socket and connection wiring. Make Legrand (Myrius), Schneider (Zencelo), Anchor (Ave). Metal boxes boards are to be concealed in the wall for 4 Module | — | — | — | 10,107 | |
| — | 400.00 | — | — | ||
| Supply, fixing, testing, and commissioning of modular type switch 6/10 Amps as per tech. specification IS/IE rules and site requirment. | — | — | — | 77,976 | |
| — | 100.00 | — | — | ||
| Supply, fixing, testing, and commissioning of modular type switch 16 Amps as per tech. specification IS/IE rules and site requirment. | — | — | — | 23,813 | |
| — | 100.00 | — | — | ||
| Supply, fixing, testing, and commissioning of modular type 6 pin switch socket 6/15 Amps as per tech. specification IS/IE rules and site requirment. | — | — | — | 33,862 | |
| — | 100.00 | — | — | ||
| Supply, fixing, testing, and commissioning of modular type multi socket 6 Amps 5 pin as per tech. specification IS/IE rules and site requirment. | — | — | — | 18,970 | |
| — | 7000.00 | — | — | ||
| Supply and recessing/fixing of 25mm (Medium) PVC conduit pipe conforming to IS 9537/Pt.III/1983 or Latest Version with accessories,junction box, etc including making chase, plastering/clamping etc as per technical specifications. | — | — | — | 2,67,960 | |
| — | 8000.00 | — | — | ||
| Wiring for light points with supply and laying of FRLS PVC insulated multistranded copper conductor cable 1100 Volt 1x1.5 Sq.mm multi stranded confirming to IS-694 latest in the existing PVC pipe. | — | — | — | 1,11,360 | |
| — | 4000.00 | — | — | ||
| Wiring for sub-main with 2x2.5 Sq mm FRLS PVC insulated multistranded copper conductor s/core cable in the recessed PVC conduit pipe 25 mm dia as required at site. | — | — | — | 1,46,360 | |
| — | 2500.00 | — | — | ||
| Wiring for sub-main with 2x4.0 Sq.mm FRLS PVC insulated multistranded copper conductor s/core cable in the recessed PVC conduit pipe 25 mm dia as required at site. | — | — | — | 96,075 | |
| — | 600.00 | — | — | ||
| Supply, fixing, testing and commissioning of LED tube light system wattage 18 Watt to 20 Watt complete with all mounting arrangement & accessories & flexible copper wire for connection from ceiling rose as per ISS/IR rules & site requirement as per CEE/NR Specification No.CEE/NR/121-Elect/PS/2018 (Rev '3') Dated 28.06.2018 & CEE/NR/121-Elect/PS/2019 (Rev.4) dated 04.11.2019 or latest, | — | — | — | 3,30,006 | |
| — | 600.00 | — | — | ||
| Supply, fixing,testing and commissioning of 3-pin ceiling rose 5 Amp capacity on existing MS/PVC conduit junction boxes/casing caping Anchor, Cona, Kinjal, SSK or equivalent as per IS, IE rules and site requirement. | — | — | — | 8,904 | |
| — | 150.00 | — | — | ||
| Supply and erection of 36 W recess type LED light fitting (2x2 ft) complete with control panel & all accessories including connection with 2x2.5 sq.mm PVC insulated multi stranded FRLS copper conductor cable, testing,commissioning &earthing required and as per CEE/NR specification No. CEE/NR/121-Elect/PS/2018 (Rev.03)dated 28.06.2018 & CEE/NR/121-Elect/PS/2019 (Rev.4) dated04.11.2019 | — | — | — | 7,61,305.5 | |
| — | 150.00 | — | — | ||
| Supply, fixing, testing andcommissioning of energyefficient 230V, 50Hz a cceiling fan size of1200mm sweep havingwattage of 28W, range ofvoltage operation at various speed - 120 to260V AC with 5 stepspeed control electronicregulator, copper windingcomplete as per IS : 374 - 1979 or laterst, IE rule &site requirement. MakeBajaj, Usha, Havells,Crompton, Orient orequivalent. | — | — | — | 4,48,318.5 | |
| — | 50.00 | — | — | ||
| Supply, fixing,testing and commissioning of 380mm sweep, 1400 rpm (approx) propeller type exhaust fan complete as per IS, IE rule & site requirement.Make Usha, Orient,Bajaj or equivalent | — | — | — | 1,49,230 | |
| — | 15.00 | — | — | ||
| Supply, erection, testing and commissioning of the following Double door wall mounted Pre-fabricated L.T. Distribution Boards of approved make, as per explanatory note & comprising; (i) Incoming MCCB 4Pole 63 A 35 KA B/C - 1 No. (ii). Outgoing MCB 6 to 32 A. SP 10 KA B/C (4 Nos. On each Phase) - 12 Nos. | — | — | — | 2,29,294.05 | |
| — | 15.00 | — | — | ||
| Supply, erection, testing and commissioning of the following Double door wall mounted Pre-fabricated L.T. Distribution Boards of approved make, as per explanatory note & comprising; (i) Incoming MCB 40 A DP 10 KA B/C - 1 No. (ii) Outgoing MCB 6 to 32 A. SP 10 KA B/C - 4 Nos. | — | — | — | 26,156.7 | |
| — | 5.00 | — | — | ||
| Design, Supply, fixing, testing and commissioning of outdoor type feeder pillar panel having IP-65 protection (MCCB - Incoming & MCCB - Outgoing) comprising with the following MCCB's fixed in it of make Havells, Siemens, L&T, Schneider, Legrand or equivalent conforming to IEC 60947-2 / IS 13947: 2008 & IS 8623:2008 or latest with digital measuring instrument & bus-bar arrangement and conforming to PCEE/NR's spec. No. PCEE/NR/126-Elect/PS/2019 at Tech Spec-I attached or latest and as per IS, IE rules and site requirement. a) 4P MCCB 250Amps 36kA with adjustable thermal & fixed magnetic release = 01 No. (Incoming) b) 4P MCCB 200Amps 36kA with adjustable thermal & fixed magnetic release = 01 No. (Outgoing) c) 4P MCCB 63Amps 36 kA with adjustable thermal & fixed magnetic release = 03 Nos. (Outgoing) | — | — | — | 6,80,490 | |
| — | 100.00 | — | — | ||
| Earthing arrangement by providing earth electrode of GI pipe 50 mm dia (B class) 4.5 meter long with flange including 6 SWG GI earth wire from earth pipe to connecting point on switch board to distribution board/pole etc. as per site requirement including masonry enclosure as per Tech specification at annexure 'A' relevant ISS & IE rules and site requirements. A suitable CI/MS/RCC cover as approved by Rly . Representative, cover with locking arrangement shall be provided. | — | — | — | 2,35,060 | |
| — | 1000.00 | — | — | ||
| Supply & recessing/fixing on surface 6 SWG GI wire for loop earthing as required as mentioned in explanatory note. | — | — | — | 8,970 | |
| — | 5000.00 | — | — | ||
| Transportation, Laying, underground/road/Railway track, recessing in platform /wall along with Rly. Track/in laid RCC/GI pipe as required 1.1 KV grade LT XLPE insulated armoured, aluminium conductor cable including making chase & plastering after laying of cable/digging of cable trench, sand cushioning, protective covering with second class bricks, provision of cable route marker as per Tech. Specification including end terminations with Aluminium Clamping socket/lugs, testing and commissioning of Upto 25 sq.mm | — | — | — | 2,96,400 | |
| — | 5500.00 | — | — | ||
| Transportation, Laying, underground/road/Railway track, recessing in platform /wall along with Rly. Track/in laid RCC/GI pipe as required 1.1 KV grade LT XLPE insulated armoured, aluminium conductor cable including making chase & plastering after laying of cable/digging of cable trench, sand cushioning, protective covering with second class bricks, provision of cable route marker as per Tech. Specification including end terminations with Aluminium Clamping socket/lugs, testing and commissioning of Above 25 sq.mm | — | — | — | 3,24,060 | |
| — | 30.00 | — | — | ||
| Design, manufacturing of floor mounted MS feeder post made of MS sheet 16 SWG Die pressed of size 550mm x 450mm x 275mm deep complete with Aluminium bus bars four Nos. having cable glands 2 Nos. duly grouted with cement concrete ratio 1:2:4 duly earthed with earthing terminals. | — | — | — | 1,16,231.7 | |
| — | 200.00 | — | — | ||
| Provision of Supply and Laying HDPE pipe 140 mm inner dia and 160 mm outer dia through trenchless method under Railway track/road/Platform etc Conforming to LATEST version of IS 4984 | — | — | — | 2,19,746 | |
| — | 30.00 | — | — | ||
| Supply, erection testing and commissioning of 6 mtr height single arm decorative GI pole with cast aluminium arms including 1 nos 80W tear drop pendant LED fitting along with foundation as per manufacturer's design complete. | — | — | — | 9,93,050.4 | |
| — | 20.00 | — | — | ||
| Supply, erection testing and commissioning of 6 mtr height double arm decorative GI pole with cast aluminium arms including 2 nos 80W teardrop LED fitting along with foundation as per manufacturer's design. | — | — | — | 8,29,236 | |
| — | 8.00 | — | — | ||
| Supply ,erection, testing and commissioning of Facade lighting with controller and accessories as per explanatory note. | — | — | — | 88,46,716 | |
| — | 10.00 | — | — | ||
| Provision of cutting & removing of all type pole including dismantling of foundation & pole to be deposited in SSE/P store. | — | — | — | 8,457.5 | |
| — | 7.00 | — | — | ||
| Supplying, erection, testing & commissioning of 16 Meter high mast system with its accessories. Mast shall be in two sections, hot dip galvanised and suitable for wind velocity as per IS 875 part 3. It shall also include accessories for high mast including head frame, steel wire rope 6mm dia 7/19 construction) double drum winch, Galvanised lantern carriage arrangement suitable for 8 luminaries symmetrically and its control gear boxes and its lighting finial. The mast shall have an integral power tool installed inside the base compartment for its operation. Erection and commissioning of the high mast with the help of suitable equipments. | — | — | — | 20,00,871.67 | |
| — | 56.00 | — | — | ||
| Supply, installation,testing and commissioning of 150 Watt LED based flood light fitting, operating voltage single phase 230V AC, 50Hz complete with led lamp & all mounting arrangement, accessories & flexible copper wire for connetion as per ISS/IR rules & as per CEE/NR Specification No. CEE/NR/121-Elect/PS/2018 (Rev.03) dated 28.06.2018 & CEE/NR/121-Elect/PS /2019 (Rev.4) dated 04.11.2019 respectively or latest | — | — | — | 8,79,351.2 | |
| — | 7.00 | — | — | ||
| Fabrication, supply and erection of Fencing around the high mast in square shape size 2M x 2M and height 1.5M from ground level fabricated from MS angle size 40x40x6mm, MS Flat size 40x6mm and wire mesh made of 8SWG wire and 1M wide hinged type lockable door as per drawing approved by Railway including grouting, CC platform around the high mast above 0.30M above ground level and painting etc. and as per technical specification. | — | — | — | 40,933.34 | |
| — | 7.00 | — | — | ||
| Design, manufacturing, supply, erection, testing and commissioning of astronomical timer switch along with TPN 63 Amps and associated accessories as per detail (a) Astronomical time switch model SEL-170 tiop of Indo Asian or equivalent MDS, Legrand, Siemens, L&T, ABB, AEG (b) 65 Amps TP contactor model No. LBF 650 A or equivalent of L&T, Siemens, ABB, AEG (c) TPN MCB 63 Amps (d) Accessories like wiring, locks, hinges, gaskets, nuts & bolts etc. (e) MS fabrication box 2 mm CRCA sheet size 17"x12"x6" powder coated to 50 micron thickness. | — | — | — | 1,59,603.99 | |
| — | 7.00 | — | — | ||
| Supplying, Installation, testing & commissioning of foundation bolts manufactured from special steel along with nuts, washers, anchor plates and templates including design and casting of suitable shallow foundation with M-15 concrete for the high mast considering the safe soil bearing capacity at site as 10 T/Sq. Mtrs. at 2 mtrs depth. | — | — | — | 1,55,708.14 | |
| — | 7.00 | — | — | ||
| Supplying, Installation, testing & commissioningof twin dome aviation obstruction light with 2 nos. LED lamps. (One fitting per mast is necessary if no taller structure are in near vicinity). | — | — | — | 12,360.74 | |
| — | 20.00 | — | — | ||
| Supply, installation and commissioning of light weight wall mounted voltage stabilizer confirming to IS: 8448 suitable with toroidal care transformer having capacity 4 KVA, Input Voltage 135-290V and output voltage 220-240 V, MCB 32 Amps, time delay relay (2-4 min) with soft touch type instant and start switch, under voltage and over voltage cut off with indicators, Digital Voltmeter and Ammeter with soft type selector switch for measuring input & output voltage, indicator for power ON and timer ON. IS 8448 Latest version/Make Microtek, V-Guard or equivalent with RDSO/ISO/BIS/equivalent certification | — | — | — | 1,42,787.6 | |
| — | 100.00 | — | — | ||
| Supply, installation, testing and commissioning of 70 watt LED Medium bay light fitting, operating voltage single phase 230V AC, 50Hz complete with led lamp & all mounting arrangement, accessories & flexible copper wire for connetion as per ISS/IR rules & as per CEE/NR Specification No. CEE/NR/121-Elect/PS/2018 (Rev.03) dated 28.06.2018 & CEE/NR/121-Elect/PS /2019 (Rev.4) dated 04.11.2019 respectively or latest | — | — | — | 3,71,194 | |
| — | 2500.00 | — | — | ||
| Supply & erection of 103 mm Inner dia Double Walled Corrugated pipe in ground under Railway track/road as required and as per explanatory note.. | — | — | — | 8,51,825 | |
| — | 1000.00 | — | — | ||
| Design,manufacture,supply and display of wall / hanging / floor mounting type LED illuminated signages /direction boards confirming to RB guidelines fo rtechnical specification circulated videLetter No.2023/SD-II/22/07/02,Dtd.15.05.2023(copy enclosed asAnnexure). | — | — | — | 28,08,600 | |
| — | 1000.00 | — | — | ||
| Erection andinstallation ofwall /hanging /floor mounting type LED illuminated signages /direction boardsin half elliptical shape | — | — | — | 2,80,860 | |
| — | 8.00 | — | — | ||
| Supply, fixing,testing andcommissioning of25A/32A, 30 mARCCB AC typeconfirming toIS12640-1 &IEC61008-1 with10KA short circuitwithstand capacitycomplete withenclosure forWater Cooler, AC,WaterGeyser &Refrigerator. | — | — | — | 15,187.76 | |
| — | 30.00 | — | — | ||
| Supply, fixing, testing andcommissioning of Bracket fans wallmounting of size 450 mm(18 inches).Make: Bajaj, Khaitan, Crompton 230Volts, 50 Hz AC supply. | — | — | — | 87,027.9 | |
| — | 68.00 | — | — | ||
| Design manufacturing, supply fixing, testing and commissioning of LED based station Name boards(ENGLISH) in RGB colaor complete with connected accessories with all supporting work to be installed on Railw ay structures(each letter). | — | — | — | 9,93,052.28 | |
| — | 64.00 | — | — | ||
| Design manufacturing, supply fixing, testing and commissioning of LED based station Name boards(HINDI) in RGB colaor complete with connected accessories with all supporting work to be installed on Railw ay structures(each letter). | — | — | — | 10,38,821.76 | |
| — | 67.00 | — | — | ||
| Design manufacturing, supply fixing, testing and commissioning of LED based station Name boards(Punjabi) in RGB colaor complete with connected accessories with all supporting work to be installed on Railw ay structures(each letter) | — | — | — | 10,87,516.53 | |
| — | 1.00 | — | — | ||
| Supply, Installing, Testing & Commissioning of High Volume Low speed (HVLS) Fan,3 phase, 1.2 KW, 20 Ft. Diameter, 6(six) blade with control panel and all acessories. (Make/Brand- ECOAIR Or similar) | — | — | — | 4,04,250 | |
| — | 75.00 | — | — | ||
| Supply & erection of 5Mpole with single armbracket hot dip galvanizedoctagonal pole with top 70mm and bottom 130 mmaround face made of 3mm thick, steel base platesize 200x200x12 mmcomplete with appropriatesleeve at the top of thepole for mounting armbracket 300 mm longsuitable for LED streetlight fittings includingcasting, muffing with cement concretefoundation (1:2:4)painting, earthing andfoundation GI nut, boltswith washer and smartpack junction box withsingle pole MCB andterminals as perexplanatory note | — | — | — | 5,60,462.25 | |
| — | 75.00 | — | — | ||
| Supply & erection of 5M pole with double arm bracket hot dip galvanized octagonal pole with top 70 mm and bottom 130 mm around face made of 3 mm thick, steel base plate size 200x200x12 mm complete with appropriate sleeve at the top of the pole for mounting arm bracket 300 mm long suitable for LED street light fittings including casting, muffing with cement concrete foundation (1:2:4) painting, earthing and foundation GI nut, bolts with washer and smart pack junction box with single pole MCB and terminals as per explanatory note | — | — | — | 7,48,382.25 | |
| — | 245.00 | — | — | ||
| Supply and erection of minimum 45 W LED Street light fitting operating voltage single phase 230 volts AC, 50Hz complete with all accessories as per CEE/NR Specification. No.CEE/NR/121-Elect/PS/2018 (Rev '3') Dated 28.06.2018 & CCE/NR/121-Elect/PS /2019 (Rev.4) dated 04.11.2019 or latest respectively including connection with 2x2.5 sq.mm PVC insulated multi stranded FRLS copper conductor cable, testing, commissioning & earthing required and as per explanatory note. | — | — | — | 7,87,760.75 | |
| — | 1900.00 | — | — | ||
| Fabrication, supply andinstallation of PerforatedGCGI cable Tray of 300mm widex 75mm deep x 1.6 mmthick including horizontal and vertical bends,reducers, tees, crossmembers and other accessories duly galvanized and supporting/ mounting with pillar/angle structure/wallas required at site and as per of explanatory note. | — | — | — | 15,48,614 | |
| — | 372.00 | — | — | ||
| Supply, fixing, testing and commissioning of 4-feet long surface mounting 36-watt, 5700K, CRI>80, LED Luminarie Fitting shall be environmental friendly, long life, corrosion resistant, impact proof IP66 with PC housing & opal finish cover suitable for wet location .Similar to Make- Havells Model No. MAGNUM NEO or Equivalent .Fitting shall be suitable for operation on single phase 240Volt, 50 HZ AC supply.Conforming to CEE/NR's spec. No. CEE/NR/121-Elect/PS/2018 (Rev- '3') or latest at Tech Spec-III attached &PCEE/NR's spec. No. PCEE/NR/121-Elect/PS/2019 (Rev- '4') at Tech Spec-IV attached or latest. | — | — | — | 19,64,160 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
ACS11.pdf
ATTACHMENT
balanceworkTD.pdf
ATTACHMENT
RDSOHMTspec1.pdf
ATTACHMENT
SpecificationsforRGBLEDbasedstation_1.pdf Station name board tech speci
ATTACHMENT
GCC_April-2022_2022_CE-I_CT_GCC-2022_POLICY_27_04_22.pdf
ATTACHMENT
LEDSpecification.pdf
ATTACHMENT
LEDSpec.1.pdf
ATTACHMENT
LEDSpec2.pdf
ATTACHMENT
GCCCorrectionSlip.pdf
ATTACHMENT
ACS3.pdf
ATTACHMENT
ACS2_1.pdf
ATTACHMENT
ACS5.pdf
ATTACHMENT
ACS6.pdf
ATTACHMENT
ACS4.pdf
ATTACHMENT
RewirngSpec-I.pdf
ATTACHMENT
ACS7.pdf
ATTACHMENT
ACS8.pdf
ATTACHMENT
ACS9.pdf
ATTACHMENT
ACS10.pdf
ATTACHMENT
GCCClarificationRegarding.pdf
ATTACHMENT
1121.pdf
ATTACHMENT
1212.pdf
ATTACHMENT
SpecificationsforRGBLEDbasedstation_1.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .