GE 874/EWS-76/2022-23

Amount

E/M Portion

Supply, installation, commissioning and testing of 30 KVA KOEL Green Liquid Cooled silent DG Set comprising of KOEL make Liquid Cooled Diesel Engine Model 3R1040T-G1 (CPCB II Norms Compliance) developing 52 BHP @1500 RPM 30 KVA Koel Green Make Alternator rated at Three Phase, 415 Volts, 50 Hz, 0.8 PF @ 1500 RPM both mounted and aligned on a common MS Base frame complete with MS fuel Tank, Manual Control Panel, Residential exhaust silencer, AVM pads fitted on baseframe, 01 Nos 12 Volts Battery, (KOEL) battery leads, 1st fill of Lube oil all housed in sound proof acoustic enclosure protected with asbestos rope independently supported from engine to outside power house upto 1 mtr, AVM pads foundations as per manufacure design battery start with suitable size of cable for connecting upto panel board . DG Set should be capable of operating in temperture range (-25* C to + 35*C) fitted with Cold starting kit with and including the following . Make KIRLOSKAR/KOELGREEN

(A) Prime mover Vertical diesel engine of suitable capacity water cooled closed circuit as per BS-649 or IS-10002 direct injection type turbo charged electric starting system having rated speed 1500 RPM. The DG Set shall be capable of running 24hrs continuously with 10% over loading for one hrs continuously in every 12 hrs as per BS -649. Engine shall be eqipped with with all standrd fitting and mounted on common base frame with following fittings. (a) RPM cum hour meter (b) Barttery charging Ammeter ( c) ignition key and starting with push button switch (d)Lubricating Oil pressure gauge (e) Electronic governor controlling Oil temo gauge (g) 24 Volts starting equipment comprising of the following fittings (i)12 V Battery,180 AH-02Nos (ii)Battery charging alternator (iii) Self starting of suitable capacity (iv) Battery leads of copper cable with brass thimbles and terminals. (v)starting gear engine.

(D) Other fittings (i)Battery charger having electric circuit consisting of triodes , capacitor and resistances etc. The battery charger should be able to charge the battery at all times whenever the electric supply given to battery charger through control panel or electric power point. (ii) In built Fuel tank of suitable capacity as per manufacturers instructions capable for12 hrs running of DG Set inside the canopy base with all connecting pipes upto fuel pump and including oil level indicating gauge drain air vent plug etc. (Note : The rates of this items including the commissioning & testing complete (POL for DG Set testing will be issued by MES)

Supply and Laying, jointing and testing XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross section area 10 Sqmm 2 core complete laid in trenches, ducts or fix to pipe, on walls, poles complete all as specified and directed. Note :- Earth work shall be measured and paid saparately.

Supply and Laying, jointing and testing XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross section area 35 Sqmm 3.5 core complete laid in trenches, ducts or fix to pipe, on walls, poles complete all as specified and directed. Note :- Earth work shall be measured and paid saparately.

Supply and Laying, jointing and testing XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross section area 25 Sqmm 4 core complete laid in trenches, ducts or fix to pipe, on walls, poles complete all as specified and directed. Note :- Earth work shall be measured and paid saparately.

Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50m depth for foundation, laying of cables/pipes/poles etc., and getting out in hard/densesoil complete all as specified and directed.

All as per item above byt exc 1.50 but n.exc 3.0m deep complete all as specified and directed.

Returning filling in including spreading levelling watering and well ramming in layers not exceeding of 25 cm thick in soft/loose soil complete all as specified and directed

Removal of surplus soil as obtained from excavation to a distance not exc. 50 Mtr and depositing where directed at a level not exc. 1.5 Mtr above the starting point all as specified and directed.

Supply and laying dry river sand for cable cushioning in trenches to required width at bottom and top of cable including spreading levelling watering and consolidation complete all as specified and directed by Engineer-in-charge. Note:- Punned thickness only shall be measured and paid.

Supply and laying old size brick covering with width equal to length of brick as the mechanical protection to cable with well burnt sub class 'B' laid in trenches flat complete all as specified and directed by Engineer-in-charge.

Supply and fixing tubes light grade GI tubing 40 mm dia with all fitting laid in trenches.

Supply and fixing tubes light grade GI tubing 50 mm dia with all fitting laid in trenches.

Supply only street light Engineering plastic one piece moulding control box with locking arrangment made out of HDPE and FI clamp 25 x 3mm complete of dimensions in CM +/-10%(34x28x13) including MCB SP 6 Amp 240 Volts complete with 02 Nos aluminium busbar or terminal two nos (2P-R/Y/B and N) of rating 63 amps for single phase and neutral on porcelain based insulators. Make : Sintex/ Hensel/ SHI/BRITE

Supply ,erecting and fixing the true vertical position,steel tubular swaged pole(410 SP-31),09 mtr long, complete with cast iron base plate,pole cap/final taper plug ,bolts, nuts and washers, welded reduced section and longitudinal weld throughout entire lenght of pole ,including two coats of black bituminous paint externally upto planting depth and remaining exterior portion of pole shall be provided with one coat of red oxide primer and two coats of aluminium paint complete all as specified and directed. (Numbering of the poles shall be done with synthetic enameled painted letter of shape & size as directed). Note:- (a) Cost of numbering of pole shall be deemed to included in unit rate. (b) Excavation, Earth work and PCC foundation will be measured and paid for separately.

S & F GI bracket made out of GI pipe light grade of size 50/40/32 mm 1.2 m long cut to length bend to the required shape and 02 Nos mounting flat iron clamps size 40mm x 6mm, 04 Nos hexagonal bolts 10mm dia 100mm long with nuts and washers complete all as specified and directed.

Supply and fixing LED street light luminaries 70/72 Watt having shall be made of single piece Aluminium Die cast with powder coated in RAL-7032 shade with heat distribution fins onhousing with UV stabilized toughned flass cover and should have secondary lens on each LED for better light distribution .The system luminaire efficacy should be > 110 LM/W with high power LED of Philips/Osram/Cree/Nichia Make.LED driver should be potted and BIS certified with efficiency > 85 % frequency 50 HZ,Operating voltage range 120V-270V,current not more than 0.320 Amp,PF 0.95, THD (I) < 10 %, supported with 5 KV internal and 10 KV external SPD, Humidity 10% to 90 % RH, working temperature - 20⁰ C to 50⁰ C lige expectancy of LED should be 50000 burning houres with minimum 70 % initial lumene maintained, CRI >70. Make:- Cat Part No LSTP-72-CDL-M OF Crompton or equivalent Make in Havells/Halonix/Phillips LED

M&L for plain cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) in foundation of PCC poles/struts as specified including necessary form work, complete all as specified & directed.

M&L for plain cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregate) in foundation of stay assembly etc including necessary form work, complete all as specified & directed.

M&L for plain cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) for coping around poles, including necessary form work finishing even and smooth without using extra cement, complete all as specified & directed.

Supply and fixing 1100 volts grade heavy duty cable with PVC insulated solid aluminium conductor served with an inner sheathing of PVC tape and overall PVC sheathed of size 2.5/4 sqmm 2/3 core suitable for LED security light for pole box to street light fitting with connector and thimble,nut&bolt and washer etc., complete all as specified and directed.

M & L for carrying out boring under the black top road for crossing of LT cable/protection pipe by any means without damaging black top surface of road for fixing of GI pipe upto 80mm bore under the road complete all as specified and directed.

M & L On Load change over switch 415 Volts in sheet metal enclosure 4 pole of 63 Amp Capacity complete all as specified and directed.

Taking down copper/aluminium point wiring ( light fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc removing material to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) asd making good distribued surface of wall , floor etc complete all as specified and directed.

Point wiring for one light point/Ex/fan point controlled by one switch with 1.5 sqmm PVC FRLS insulated un-sheathed copper conductor single core multi strand cable and 1.5 sqmm PVC FRLS insulated un-sheathed copper conductor single core multi stranded cable (green color) as earth lead in and including cable 1100 volts grade including 25mm casing and capping (ISI marked) for one light/ fan point controlled by one switch including CI/MS sunk box of required size, & as directed by Engr in Charge including 3mm thick plastic laminated top sheet cover, including cutting chases to wall and making good the disturbed surfaces to match with the existing specification complete all as specified. Note - Wiring will be as per SSR Part-I and Part II Spoecification and wire will be orignate in DB and end in lt end.

All as per item above but for 3 pin 5 amps socket outlet on independent board complete all as specified and directed.

All as per item above but for 3 pin 5 amps socket outlet on the same board with other switch complete all as specified and directed.

All as per item above but wiring with 2.5 sqmm copper wire ( FRLS) and 1.5 sqmm earth wire for socket outlet 6 pin 15 amps on independent board complete as directed by engineer in charge .

Supply & fixing Switch piano type flush 6 Amp Single pole one way ( ISI Marked) complete all as specified and directed. Make : Havells/Anchor

Supply & Fixing Socket outlet 2 in1, 3 pin 5 Amps flush type complete all as specified and directed.Make : Havells/Anchor

S&F Switch socket combination 5 in 1, 5 and 15 Amp flush type universal controlled by one switch (ISI marked) complete all as specified and directed.

Supply & Fixing ceiling rose surface backelite 65x50mm two to three terminal (ISI marked).Make : Havells/Anchor

S & F lamp holder/batton holder/angle holder insulated body with bakelite back plate suitable for fittings complete all as specified and directed.

S & F in replacement of CFLs with LED Lamp, B22 type, 14 watt,complete all as specified and directed.

M&L for LED Batten 1x20 W for regal batten for LED Universal batten for G 13 T with 18 W tube rods and Ultra bright LED Polycarbonate tube light very high efficiency suited for installation in existing T8 and connecting electrically using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core all as required at site or directed by Engineer-in-Charge.

Supply and fixing LED luminaire 600 mm x 600 mm,35/36 watt, 220 V AC ecessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete.

S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size all as specified and directed.

M & L for providing/ cutting the round/ square hole of required size in fabricated wall finishing the distrubed surfaces as per existing finishes complete all as spd and supply and fixing propeller PVC type AC ventilating fans, Single phase, 230 volts 250 mm sweep completefixed with proper size nut s & Bolts in fabricated wall, fixing the frame on the exhaust side (outer surface of the wall) and connecting with and including PVC insulated three core 1.5 sqmm copper cable from ceiling rose to exhaust fan motor and writting MES No. with black synthetic enamel paint 2.0 cm high complete all as spd and directed by Engr-in-charge.

S&F 15W LED Recess mounted Height adjustable downlighter with pressure die-cast aluminium heat sink & PC diffuser in white powder coated finish with integrated driver complete including taking down the old fittings.

S&F in replacement sub Main Wiring with two PVC insulated unsheathed multistrand FRLS flexible copper conductor cable of size 2x6 sqmm and one PVC insulated multistrand unsheathed FRLS flexible copper conductor cable of size 6 sqmm (green colour) as earthing lead connecting to main earthing dolly drawn in and including non metallic PVC concealed conduit 20mm dia complete and making good to disturbed surface complete of wall/floor with cement mortar and finishes to match the existing surface complete all as specified and directed.

S & F in replacement of sheet metal enclosure MCB distribution board, double door with IP-43 protection single phase 240 volts 8 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases in wall for fixing DB and making good the distributed wall surfaces to match with existing specification complete all as specified and directed.

M & L for MCB SP 240 volts any rating from 6 to 40 amps, 'C' cruve with rupturing capacity 10 KA, including providing thimble for out going cablescomplete all as specified and directed.

M & L for MCB SPN 240 volts any rating from 6 to 40 amps, 'C' cruve with rupturing capacity 10 KA, including providing thimble for out going cablescomplete all as specified and directed.

S & F in replacement of old unsverviceable sheet metal enclosures distribution boards, double door three phase 415 volts 6 ways vertical TPN DB for comprising three phase four wire copper strip bus bar of appropriate capacity complete all as specified and directed and comprising of the following (a)MCCB FOUR POLE 125 AMPS AC 415 VOLTS 25 KA=01 NO as incoming and 12 nos. MCB SP 40 Amps, C series as outgoing (Note :- (i)The DB shall be VTPN series of Schenieder Cat Part No:- A9HVD04L or equivalent in any of the make mentioned in list of product . (ii) The DB shall be flush fixed ,and making good the disturbed surface matching with existing specifications shall be part of job at no extra cost.(iii)connection of theMCCBs/ MCBs with cable shall be made through appropriate size pin /bottle type thimble -properly crimped.(1v) all the vacant holes of the DB shall be provided with blank plates of appropriate size. (v) double continuous earth wire shall be provided for each three phase DB from earthing mains dolly (vi)MCCB's and MCB's should have a same make as of DB.

S & F in replacement bldg secuirty light fitting energy saving high efficiency LED street light fitting 25 Watts, 5700 K, IP 66, having pressure die cast housing with toughened glass and individual high power LEDs with secondary optics, prismatic polycarbonate cover complete including GI bracket of size 32 mm dia bent to shape having length on less than 1.5 mtr fixing with clamp etc and making connections using cord flexible 3 core copper cable of size 23/ .0076 from ceilling rose/ PVC connector to light fittings or as directed by Engr-in-chrage.

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6.3cm thick burried directly in ground ( earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to galvanised iron wire 4.0mm dia by means of bolts, nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 connected to earthing test all as specified or indicated including testing on completion.

Supply, Installation and Testing Hot & Cold, Invertor Split type Air Conditioner, electric driven, Single Phase, 240 volts, Five Star BEE Rating with Remote Control System, capacity 1.5 Tonnes, with in-built air ioniser and plasma filter for better indoor air quality including necessary wiring and making fixing arrangement for indoor and outdoor unit complete all as specified and as directed. Make :- Voltas/ Daikin/ LLoyd. Note : The Split AC shall be fitted all as directed at site. The contractor shall make arrangement for cutting chases for laying gas pipes including supply and fixing the copper gas pipes from the indoor unit to the outdoor unit and making good the disturbed surface to match the existing surface. The quoted rate of the contractor shall be deemed to be inclusive of this provision.

Supply and fixing Deep freezer hard top 200 litre capacity having single door. Make : Blue star, Voltas, Shri Ram (Usha).

Supply and fixing refrigerator, electric driven (single phase), capacity 260 Litres, BEE 5 star rated. Make : Voltas, LG, Whirlpool.

Supply and fixing Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 130 V to 300 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 02 KVA complete all as specified and directed. Make :- Microtek/V-Guard/Vinitec.

S&F single pole and neutral enclosure with two pin and earth plug and socket complete with one single pole MCB 20 amp complete all as specified and directed. Make : C&S Electric/ Havells/HPL.

Taking down and Dismantling of old unserviceable ceiling mounted double doom Led OT light any type and model, supply and fixing, testing and commissioning of new ceiling mounted double doom Led OT light (Shadow less) including power backup of minimum 30 Minuts and the lights suitable for fixing on cealing/roofing whith all component and connecting material including in this items, the technical parametr of the shadow less light is under illumination intensity upto 1,40,0000 Lux +1,40,0000 Lux ,(±10%) of illumination intensity,Spot Diameter /Focus dia 150-250mm (±10%) of diametr/focus,foucus adjustable and Osram Led Bulbs ,Number of Led Bulbs 96 + 96,Optimized Deep Cavity,LEDs Average Life 50000 Hrs ,Dimeter of light 500mm (±10%) of diameter,Power Supply 220V/50Hz AC drive by DC 24 Volt , special Function including remote Operated-ON/OFF,Digital control panel ,Light intensity Adjustment 0% to 100% & White balance adjustment ,SMPS control unit ,LED Colour (Yellow & White Combination) all as per manufacturer instruction/ design and its errection should be carried out under the supervision of manufacturer. Note: - ISO 9001:2015, EN ISO 13485:2012 certificate and Minimum warranty of 12 months from the date of commissioning of OT lights will be provide by the contractor . Make:- Philips, CG, WIPRO, Crompton Greaves, GEC or equivalent make as approved by GE. Note :- The Contractor will submit make and detail specification for recommendation of Engr-In-Charge, approval of GE and CO MH before purchasing the doom LED Lights.

GH MOHD SHAH AND CO

AAKASH CONTRACTORS

M/S S. D. BUILDERS

M/S ABDUL AZIZ MIR

Bidder Name

M/S S. D. BUILDERS

FG CONSTRUCTION

M/S ABDUL AZIZ MIR

GH MOHD SHAH AND CO

AAKASH CONTRACTORS