Construction of New District Police Office building with development works for the newly formed Ranipet District

Amount

1.1 : Earth work excavation in all soils (including refilling) a. 0 to 2 mt.

b. 2 to 3 mt.

1.3 :Earth work excavation in Soft disintegrated rock (including refilling) a. 0 to 2 mt.

b. 2 to 3 mt.

1.5 : Earth work excavation for Open foundation (excluding refilling) a. 0 to 2 mt.

b. 2 to 3 mt.

1.6 : Earth work excavation for Open foundation for drains (excluding refilling) width upto 1.25 m a. 0 to 2 mt.

2.6: Supply and Filling of 40mm HBSJ

2.7: Supply and Filling of 20mm HBSJ

7.2 : Supply and fixing of Bituminous filler pad, 20 mm tk. for expansion joint

13.1 : Filling with Excavated Earth

21.2 : Teak wood Wrought & Put up a. T.W. over 2 m & below 3 m

b. T.W. below 2 m length.

25 : M.S.Holdfast

31 : Weathering course

37.1 : White washing 3 coats (slaked)

39 : M.s Grills

40 : Painting - New "wood work"

41 : Painting - New "iron work"

45 : Stucco Plastering 12mm thick

46 : S & F 20 mm dia Alu. Hanger Rod

47 : S & F Alu Towel rail 75 cm long

48 : S & F 5 pin Coat stand

49 : S & F chromium plated 8 guage Picture Hook

50.4 : Providing Tree guard

52 : PVC Water supply (ASTM) a. 32 mm dia

b. 25 mm dia

53.3 : C.I. Steps ( 5 kg)

55.2 : Flat Back Urinal

Electrical arrangements 69 : 15 Amp. Power plug

72 : Box type Fibre Fan hook

74 : Charges for fixing of "Fan"

76 : 8 SWG wire

77.3 : S&F of TV/Telephone line Socket

77.4 : S&F of 20mm dia PVC pipe for TV/Telephone line

78 : Earthing Station IS3043 (Type I)

86 : Anti termite treatment

87 : ELCB Single Phase

112 : S & F of Exhaust Fan 300 mm dia

ANNEXURE-I 2.1.1 : Supplying and filling with gravel

2.1.3 : Filling crushed stone sand

3.1.1 : C.C.1:5:10 for Foundation & Basement (using crushed stone sand)

3.2.1 : P.C.C. 1:2:4 for Foundation & Basement and other similar works (using crushed stone sand)

3.3.1 : P.C.C. 1:8:16 using 20 mm broken brick jelly (using crushed stone sand)

3.8.1 : P.C.C. 1:4:8 using 40 mm HBGS Jelly (using crushed stone sand)

3.9.2 : PCC 1:3:6 for foundation & basement using 20mm metal (using crushed stone sand)

6.5.1 : Brick work in C.M. 1:5 (F& B) using Kiln Burnt Country bricks of size 22 x 11 x 7 cm (8 3/4" x 4 1/4"x 2 3/4") (using crushed stone sand)

8.1.1.1 : Standardised concrete Mix M20 Grade concrete. (using crushed stone sand) a) In Foundation and Basement.

b) In Ground Floor / stilt floor

c) In First Floor.

d) In Second Floor.

e) In Third Floor.

f) In Fourth Floor.

g) In Fifth Floor

9.5.1 : Brick work in C.M. 1:6 using Kiln Burnt Country bricks of size 22 x 11 x 7 cm (8 3/4" x 4 1/4"x 2 3/4") (using crushed stone sand) a. In Ground Floor

b. In First Floor

c. In Second Floor

d. In Third Floor

e. In Fourth Floor

f. In Fifth Floor

10.5.1 : Brick partition work in C.M. 1:4 using Kiln Burnt Country bricks of size 22 x 11 x 7 cm (8 3/4" x 4 1/4"x 2 3/4") 110 mm tk (B.P.) (using crushed stone sand) a. In Foundation and basement

b. In Ground Floor

c. In First Floor

d. In Second Floor

e. In Third Floor

11.5.1 : Brick Partition work in C.M. 1:4 Kiln Burnt Country bricks of size 22 x 11 x 7 cm (8 3/4" x 4 1/4"x 2 3/4") 70 mm tk (B.P.) (using crushed stone sand) b. In First floor

c. In Second floor

d. In Third floor

14.1.1.I : Precast Cupboard slab 20 mm tk using standardised concrete mix M20 grade.(using crushed stone sand) b. In First floor

c. In Second floor

d. In Third floor

14.1.1.II : Precast cupboard slab 40 mm tk using standardised concrete mix M20 grade.(using crushed stone sand) a. In Foundation & basement

c. In First floor

16.1.1: Precast Jally ventilator 50mm tk.using standardised concrete mix M20 (annexure) without vibrating charges a. In Ground Floor

18.1 : Formwork using M.S.Sheet a.For Column footings,plinth beam,Grade beam,Raftbeam,Raft slab etc.,

b.Plain surfaces such as Roof slab,floorslab,Beams,lintels,lofts,sill slab,staircase,portico slab and other similar works

c.For Square and rectangular columns and small quantities

d.For Vertical wall

e.For Circular Column

f.For Curved surface

21.5.2 : Supply and fixing Solid UPVC door shutter with frame

21.5.2.1 : Supplying and fixing of double Leaf solid core flush door shutter of thickness 35mm a) door size 1500 mm x 2400mm (Double leaf)

b). door size 1200mm x 2400mm (Double Leaf)

21.5.5.1 : Supplying and fixing of Single Leaf solid core flush door shutter of thickness 35mm a) door size 1000 mm x 2400mm (Single Leaf)

b) door size 900 mm x 2400mm (Single Leaf)

c) door size 750 mm x 2400mm (Single Leaf)

21.5.5.2 : Supplying and fixing of Single Leaf solid core flush door shutter of thickness 35mm a) door size 900 mm x 2100mm (Single Leaf)

22.3.3 : T.W. frame & T.W styles & rails with BWR double leaf shutters for Cup board/ward robes including two coat enamel paint & one coat primer.

26.1 : Flooring in C.C.1:5:10 (using crushed stone sand)

28.1 : Floor plastering in C.M. 1:4, 20 mm tk. (using crushed stone sand)

29.5.1: Supplying and laying Porselona (PGVT) Tiles

29.6.1 : Providing Acid proof ceramic tile using Grout (Tile Joint Filler)

29.8.1 : Glazed tiles using Grout (Tile Joint Filler) (using crushed stone sand)

29.9.1 : Floor ceramic tiles using Grout (Tile Joint Filler) (antiskid) (using crushed stone sand)

31.2.1 : Finshing the top of Terrace floor with one course of solar reflective Ceramic tiles with base concrete

33.1 : Plastering in C.M. 1:5, 12 mm tk. (using crushed stone sand)

34.1 : Plastering in C.M. 1:4, 12 mm tk.(using crushed stone sand)

35.1.1 : Plastering in CM 1:3, 12mm with WPC (using crushed stone sand)

35.1.2 : Spl. Ceiling plastering in C.M. 1:3, 10 mm tk. (using crushed stone sand)

36.1 : Cement mortar Border in C.M. 1:5, 12 mm tk. (using crushed stone sand) a. 150 mm wide

b. 75 mm wide

c. 50 mm wide

38.6 : One coat white cement for new walls and other similar works.

38.7 : Plastic Emulsion PAINT including primer for outer walls

43.1 : Supply & Fabrication of Mild steel / RTS grills (without cement slurry) for all sizes of rods.

44.2.1 : Rain water harvesting using defunct borewell and providing perforated cover slab a) Providing pit (M20)

b) Augering 30cm dia

44.6 : PVC SWR 110 mm dia with ISI mark type- A for Rain water down fall pipe

50.2.1 : Providing precast Kerb stone in C.C. 1:3:6, 450 x 300 x 150mm (using crushed stone sand)

50.3.1 : Supply and planting avenue trees (using crushed stone sand)

50.5.1 : Supplying. Fabricating and erection of M.S Scheme Name board (using crushed stone sand)

50.6.1 : Precast slab 50 mm tk.in C.C. 1:3:6 with fibre (using crushed stone sand)

52.4 : 20mm dia PVC water supply ASTM pipe (fully consealed in walls)

53.4 : S&F of C.I Manhole cover 60 x 60 cm (50kg weight )

53.5.2 : Wash Hand Basin of size 550 x 400 mm (White without Pedestal)

54.1.1 : S & F of 15mm dia half turn CP long body tap

54.2.1 : S & F of 15mm dia half turn CP short body tap

56.3.1: S&F of Indian Water Closet white glazed (Oriya type) of size 580 x 440mm with PVC SWR grade P' or "S' trap - In G.F.(using crushed stone sand)

56.4.1 : S&F of Indian Water Closet white glazed (Oriya type) of size 580 x 440mm with PVC SWR grade P' or "S' trap - Other than G.F.(using crushed stone sand)

57.1.2 : S & F of E.W.C (White) 500mm with PVC SWR grade "P" or "S" Trap (using crushed stone sand)

58.3 : PVC SWR pipe (Soil line) with ISI mark - type 'B'. a. 110 mm dia.

b. 75 mm dia.

58.4 : Supplying, Laying & Concealing the 50mm dia PVC ( SWR) pipe with ISI mark type - 'B' with relevant specials.

58.5 : PVC (SWR) pipe with ISI mark - type 'A' for Ventilating shaft with cowl

59.5.1 : Gully Trap using Kiln Burnt Country bricks of size 22 x 11 x 7 cm (8 3/4" x 4 1/4"x 2 3/4") (using crushed stone sand)

60.1 : PVC Nahani trap (4way/2way)

61.3 : UPVC Non Pressure pipe of SN8 SDR 34 (S 16.5) as per IS 15328/2003 a. 110 mm UPVC Non Pressure pipe

b. 160 mm UPVC Non Pressure pipe

62.1.1 : PVC Specials as per IS 10124/1982 Part II a. 110 mm dia PVC bend

b. 160 mm dia PVC bend

62.2.2 : PVC Equal Tee as per BIS 7834/1975 b. 160 mm dia PVC Equal tee

64.1 : Wiring with 1.5 sqmm PVC insulated single core multi strand fire retardant flexible copper cable with ISI mark confirming IS: 694:1990. a. Light point with ceiling rose

b. Light point without ceiling rose

c. Calling bell point with Buzzer/Calling bell

65.1 : Wiring with 1.5 sqmm PVC insulated single core multi strand fire retardant flexible copper cable with ISI mark confirming IS: 694:1990 for Fan point.

66.1 : Wiring with 1.5 sqmm PVC insulated single core multi strand fire retardant flexible copper cable with ISI mark confirming IS: 694:1990 for Staircase Light Point.

67.1 : Wiring with 1.5 sqmm PVC insulated single core multi strand fire retardant flexible copper cable with ISI mark confirming IS: 694:1990 for 5 amps 5 pin plug socket point @ Switch Board Itself.

68.2 : Wiring with 1.5 sqmm PVC insulated single core multi strand fire retardant flexible copper cable with ISI mark confirming IS: 694:1990 for 5 amps 5 pin plug socket point @ Convenient Places.

71.2 : Supplying and fixing of 32 AMPS Triple pole main switch.

75.1.2 : Supply and delivery of 48" (1200 mm) Fan with ISI mark with Eletronic Dimmer

77.2.1 : S & F of 20 amps DP plug & Socket in sheet enclosure with 32 A DP MCB in flush wall with earth connection(For AC Plug) superior variety

77.5 : Run of 2 Wires of 1.5 sqmm PVC insulated single core multi strand fire retardant flexible copper cable with ISI mark confirming IS: 694:1990.

77.6 : Run of 2 Wires of 4 sqmm PVC insulated single core multi strand fire retardant flexible copper cable with ISI mark confirming IS: 694:1990.

77.7 : Run of 2 Wires of 2.5 sqmm PVC insulated single core multi strand fire retardant flexible copper cable with ISI mark confirming IS: 694:1990.

77.8 : Run of 4 Wires of 4 sqmm PVC insulated single core multi strand fire retardant flexible copper cable with ISI mark confirming IS: 694:1990.

79.2.1: 3 Nos of 32 Amps - Fuse Unit

80.1: S & F of 450 x 375 x 20mm thick TW plank

87.1: Supplying and delivery of Three phase ELCB/RCCB

90.1 :Providing additional strutting to centering of plain surface.

98.2.1: Supply and fixing of best Indian Teak wood Single leaf Panelled door shutter (With brass fittings) a) 1200x2400mm (Single Leaf)

98.3.2.1 : Supplying and fixing of best Indian Teak wood panelled door of Double leaves shutters a) 1500x2400mm (Double leaf) (Aluminium fittings) with brass screws only

98.5.3 : Supply and fixing of best Indian Teak wood Double leaf Panelled door shutter a) 2000x2700mm (With brass fittings)

98.5.4 : Supply and fixing of best Indian Teak wood Double leaf Panelled door shutter a) 2000x2400mm (Double Leaf) (With brass fittings)

98.5.4.1: Supply and fixing of best Indian Teak wood Double leaf Panelled door shutter a.1500mm x 2400mm. (Double Leaf) (With brass fittings)

344.2 : S&F of Bevelled edge mirror 500 x 400 x 5.5mm

361.1 : Concrete designer tiles flooring (using crushed stone sand)

361.5.1: Vitrified Tiles flooring (ivory) (using crushed stone sand)

367 : Providing wooden (melamine) polish for new wood

379.4.2.1 : S & F of superfine polished with machine cut edges (Ruby Red) of size 4' x 2' of Granite slab 18 to 20mm thick (using crushed stone sand)

379.5.1 : Granite Tiles flooring (Ruby red) using 2'x1', 10mm tk(using crushed stone sand)

383.4 : providing full round nosing to the edges of granite slab.

448.2: Supply and fixing 32mm dia PVC Tee with end cap

799 : Two coats of OBD over one coat white cement for inner walls

ANNEXURE - II A1: Wallputty ( one coat)

A2 : Supplying and fixing in position of UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) for all sizes

A3: Supplying and fixing in position of UPVC Ventilator louvered ventilator type for all sizes

A4 : Providing teakwood glazed french window shutters and 5.5mm thick ground or frosted glass for panels a) 2100 x 2600mm

A5: Vertical TPN Distribution Boards (with MCCB Incomer); Double Door; IP43, as per IS 8623 III; Impact resistance IK09; Frame MCCB Incomer & Single Phase/Three Phase MCBs as Outgoing (for power loads exceeding 100A) b. 6 Way, MCCB + 18 Modules

A6: Aluminium Partition wall 1/3 5.5mm thick glass & 2/3 Novapan sheet 12mm thick outer top and bottom

A7: Supply and fixing of colour matt finish door 15 microns single leaf Aluminium door Size 1000 x 2100 mm

A8: Supplying and Fixing of Rolling shutters of all sizes (Manually operated) upto 8 Sq.m area

A9: Supplying and fixing of 2 x 2, 24W LED light (Recessed)

A10: Supplying and fixing of spot light (MASTER LED 65-50 WA 2700 KMRI636D IND)

A11: Suppying and fixing of column Guard size of 500 x 75 x 12mm

A12: Supplying and fixing of 8mm tk calcium silicate board designed and perforated for false ceiling

A13: Providing Cornice Work for using plaster of paris for calcium silicate Board False Ceiling

A14: Supplying and fixing of 300mm wide PVC expansion joint

A15: S & F of Hydraulic Door closer (Heavy)

A16: Supply and fixing of SFRC Manhole cover with frame with locking arrangements a) 600mmx600mm

A17: Supplying and Delivery of AC unit 1.50 Ton 3 Star inverter split Air Conditioner with all accessories etc.,all complete and as directed by the departmental officers.

A18: Supplying and fixing of 4 KVA V-Guard Stablizer etc.,all complete and as directed by the departmental officers.

A19: Supplying and laying of Copper pipe with Insulation etc.,all complete and as directed by the departmental officers.

A20: Supplying and fixing of Outdoor Unit Stand etc., all complete and as directed by the departmental officers.

A21: Supplying and fixing stainless steel hand rails for stairecase near wet riser

A22: Supplying and fixing stainless steel hand rails.

A23: Clearing heavy jungles inculding all charges

A24: Supplying and fixing of LED blubs suitable for fixing it to pendent / bakelite battern holder of best approved variety a) 9 watts LED bulb

b)12 Watts LED bulbs for bulk head fitting

A25: Supplying and fixing of 18W LED CRYSTAL GLASS TUBE LIGHTS 4' long with necessary fittings and charges for assembling and fixing

A26: Supply and fixing of Bulk head fitting suitable for 12W LED Bulb

A27: Supplying and fixing of following dia GI pipe in above ground level a) 50mm dia GI pipe

A28: Supplying and delivery and laying of following dia GI pipe "B" class in Below GL a) 100 mm dia GI pipe

b) 65 mm dia GI pipe

A29: Supplying and fixing of following dia GI/GM/CI specials a) 50mm dia GI Bend

b.) 50mm Dia GI Hex Nipple

c.) 50mm Dia GI Coupling

d.) 50mm Dia Non Return valve

e.) 50 mm Dia GI Union

f.) 65 mm Dia GI Hex Nipple

g.) 65mm Dia GI Coupling

h.) 65mm Dia GI Union

i.) 65mm Dia GI Tee

j.) 65mm Dia GI Elbow

k.) 65mm Dia Gun metal Gate valve

l.) 65mm Dia GI Bend

m.) 65mm x 50mm GI reducer (heavy)

n.) 40mm MS Bore Clamp set

A30 : Supplying, laying, fixing and jointing the following PVC pipes as per ASTM-D Below ground level a. 50 mm dia

A31: Providing wall panelling using one side teak wood sheet with melamine polishing with following specification. The frame using aluminium tubler section of size 50mm x 25mm x 2mm thick.

A32: Supply and installation of & 4 zone automatic fire alarm panel with fire and fault indicatications etc.,

A33: Suppply and installation of smoke detectors with base and led to operate on 24 V DC suppply etc all complete.

A34: Supplying and installation of heat detector to operate on 24 v DC supply make system sensor wl secutron

A35: Supply and installation of Electronic hooter 5 watts capacity wall mounting type

A36: Suppply and installation of manual call point with hammer and chain

A37: Supply and installation of 2 core 1.50 Sq.mm copper cable hum in suitable PVC conduict pipe (or) casing and caping junction boxes glands clamps etc.,

A38: Supply and installation of responsible indicator for smoke deductor inside rooms

A39: Supply and installation of ABC type fire Extinguishers, cylindrical in shape,wall mounting type, with intial charges and discharge Nozzle, capacity 6kg ISI marked.

A40: Supply and installations of Co2 type fire Extinguishers, wall mounting type, cylindrical in shape, with discharge Horn capacity 2 kgs.ISI marked.

A41: Supply and installation of Advanced Early Streamer Emitter type Lightning arrestor made of AISI 316 Stainless Steel NFC 102 -17 standard 79 mtrs radius protection. Make :- JMV/Gravin Model 1.0

A42: Supply and Installation of copper 18 mm Copper Rod size of 8 feet length buried in earth including excavation of earth to the depth of 8 feet and closing the pit and mixing Bentonite Chemical for fluid retention.

A43: Supply and Installation of 50mm dia GI mast of 5 Mtrs length with insulators, enamel painted to approved colour part buried in floor for supporting lightning arrestor spike and copper cable.

A44: Supply and installation of 70 sq.mm copper braided/Solid sheathed cable run on the external wall from terrace to the ground floor.

A45: Supply, installation, testing and commissioning of 160 KVA Diesel Generator set complete with all accessories Generator with auto main failure (AMF) Panel

A46: Erection, Testing and commissioning of 160 KVA Diesel generator set. Insulation for the residential silencer (supply of residential silencer to be included under item for DG Sets)

A47: Supply and installation of M.S. cable adopter box (made of 14 SWG sheet steel) with suitable copper bus extension link from alternator. The adopter box shall have tinned copper bus bar of suitable size for phases and neutral with suitable holes for cable termination (1R x 3.5 core, 185 Sq.mm). Necessary rubber gaskets between alternator and cable box shall be provided to avoid vibration between adopter box and alternator.

A48: Supply and installation of MS exhaust pipe of suitable thickness with 100mm dia upto 5m from the silencer complete with necessary supports, brackets etc. The supports shall have at intervals of not more than 2.5m.

A49: Supply and installation of MS exhaust pipe of suitable thickness with 125 mm dia complete with MS wall / ceiling support, etc.

A50: Supply and insulation of exhaust pipe thermal insulation lagging with mineral wool as per IS 3677 / 1973 reinforced with chicken mesh and cladded with aluminium sheet of 26 SWG and 50mm thick with 64 Kg/Cu. Mtr. Density.

A51: Supply and installation of stainless steel rain hood / rain cap / bend at top of the exhaust pipe to prevent rain water entry to exhaust pipe with provision of drain plug in the system.

A52: Preparation of necessary drawings for both DG sets for approval by Chief Electrical Inspector to Government / CEA, obtain approval for the same, arrange for the inspection by the Electrical Inspectorate / CEA Officials and obtain safety certificate from them for commissioning the DG set (This building is fed by HT power supply)

A53: Providing safety equipments: Co2 fire extinguisher: 1 No.; 9 ltrs capacity fire buckets: 3 Nos., & rubber mat : 1 No.

A54: Supply and laying of XLPE, aluminium conductor 1.1KV grade armoured, MV cable of the following sizes in the existing cable trays / trenches as required generally confirming to IS: 1554/Part - I / 1970 a) 3 1/2 x 185 sqmm aluminium cable

A55: Supply and fixing of brass cable gland for XLPE armoured LTUG cable for following sizes with earth connection a) 3 1/2 x 185 sqmm aluminium cable

A56: Supply and providing cable end termination of following sizes of XLPE armoured LTUG Aluminium cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete. a) 3 1/2 x 185 sqmm aluminium cable

A57: Earthing as per the ISI specification with an earth electrode of 2.1 mt class 'B' GI pipe of dia not less than 40mm, with copper earth plate of size 125mm X 50mm X 6mm, with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry.

A58: Plate earthing with copper plate of size 600 x 600 x 3 mm as per the ISI specification with an earth electrode of 2.1 mtr class 'B' GI pipe of dia not less than 40mm, with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry.

A59: Supply and run of 2 of No.8 tin coated copper for earth connections from the earth bit to the earth machine room

A60: Providing and fixing 25mm x 3mm copper strip on surface or in recess for connections as required

A61: Supplying and fixing of following size of Aluminium Dye casting letters with MRF Powder Coating a) 45CM (18")Height

A62: Supplying and fixing of following size 24" x 4" and 5" dia plastic foam plate of 3mm thick with 3" height vinyel cutting numbers

A63: Supplying and Fixing of Brass Name Board with Brass Letter

A64: Supplying and fixing of tamilnadu government Emblem of 3’-3” dia having brass edging logo brass plate giving 16 dia Supplying and Fixing of Brass Name Board with Brass Letter

A65: Supplying and fixing of following size of Aluminium Dye casting letters with coloured Powder Coating with matt finishing a) 30" Height Emblem

A66: Supplying and delivery of following Godraj NAV-TAL lock including all cost of lock etc., complete. a) 6 Lever with 3 keys

A67: Supply, Erection and Commissioning of 1No of Passengers lift (13 Persons - 884 Kgs.)at site according to the standard specification (with machine room)

A68: Supply and Fixing of UG cables on Walls / Ceiling , Charges for conveying and fixing of UG cables of sizes 4 to 25 Sqmm of 2, 3, 3.5 and 4 core with necessary MS clamps, brass screws including cost of all materials redoing the dismantled portion, etc., all complete. a) 3.5 Core 25 Sqmm Cable

A69: Supply and fixing the following copper Crimping Lugs suitable for the UG cable etc to complete. a) 3.5 Core 25 Sqmm Cable

A70: Supply and fixing the following copper Cable Gland suitalbe for the UG cable etc to complete. a) 3.5 Core 25 Sqmm Cable

A71: Lioson charges for CEIG approved for 13 person lift

A72: Annual maintenance charges for 2nd year for lift

A73: Annual maintenance charges for 3rd year for lift

A74: Annual maintenance charges for 4th year for lift

A75: Annual maintenance charges for 5th year for lift

A76: Supply & delivery for Singnamax /Amp/Molex CAT 6E UTP cable of site of work for the Lan Network wiring etc.,

A77: Labour charges for laying of CAT6 cable through the PVC pipe /Channel etc .,

A78: Supply of NT RJ 45 information Outlet box connector socket fixingcharge etc.,

A79: Labour charges for R.J 45 Box fixing and termination etc all complet,.

A80: Labour charges for providing RJ 45 connection the patch panel and to providing connection between etc., all complete.

A81: Lan intergration charges for checking data connectivity between system and to switch of the server and alingment wiring etc

A82: Supply and Gigabyte Network switch 24 port etc.,

A83: Supply of digilink /Singnamax patch panel 24 port etc., complete

A84: Supply of CAT6 Patch Card

A85: Supply Wall mountable data rack etc., complete

A86: Supply and Data Rack mountable PD unit

A87: Supply and Installation of CCSE 700 chairman Unit Long Microphone Built in speaker Make : Bosch Model No: CCSE-CML etc.,

A88: Supply and Installation of Delegate unit Long flexible gooseneck, Internal Loudspeaker automatically mutes LED Indicator, Headphones output. Make: Bosch CCSE/DL-700 Series.

A89: Supply and Installation of control Unit with following features, supplies power up To 50 Units and control up to 150 Unit Make: Bosch CCSE -CU -700 Series.

A90: Supply and Installation Ahuja Pre- Amplifier Model No: MMS55 (250W)

A91: Supply and Installation of 30 W Speaker Ahuja

A92: Supply and Installation of gooseneck, Microphone etc.,

A93: supply and Laying of 2 core Loud Speaker cable with PVC pipe and accessories etc.

A94: supply and Laying of 8 core 7/36 shielded conference cable with PVC pipe and accessories etc.

A95: Supply and Installation of 8 Pin Type Socket with suitable M.S. Box And accessories.

A96: Renewal of Supply and Installation of 1 KVA Stabilizer etc.,

A97: Supply and Installation of wireless handheld microphone etc.,

A98: Supply and Installation M.S Audio equipment rack etc.,

A99: Supply and Installtion of LCD projector

A100: Supply and Installation of 8’x6’ Motorized screen.

A101: Supply and installation of 1 ½ x 1 ½ Ceiling Mounting kit. Make: Liberty

A102: Supply and installation of 20mtrs. Length VGA cable, Power cable Audio and video cable Both end with connector.

A103: Designing the Semi Unitised Structural Glazing System with open groove joint as per design

A104: Providing and fixing of Aluminium Composite Panel (ACP) 4 sided having 50 x 25 x 1.50mm frame work

A105: Supply, fixing of 30W LED street light with necessary fittings.

A106: Supply, fixing of 60W LED street light (Superior variety) with necessary fittings.

A107: Supplying and fixing of 120W LED STREET LIGHT FITTING with necessary fittings (Superior variety) Charges for fixing

A108: Supplying and fixing of GI steel tubular pole for street light of 7 Meter length single bracket pole with base plate 250x250x6mm

A109: Supply and erection of 250 Amps capacity floor mounting panel board (Cubical type) with bus bar chamber (Incoming 1 No. 250A TPN MCCB, Bus Bar: 250 Amps 3 phase 4 wire Copper Bus Bar Outgoing 1 No. 250 A 25 KA TPN MCCB)

A110: Supply and erection of 250Amps capacity floor mounting panel board (Cubical type) with bus bar chamber (Incoming 2 No. 250A FP MCCB, Bus Bar: 250 Amps 3 phase 4 wire Copper Bus Bar Outgoing 3 Nos. 125 A TPN fixed type MCCB )

A111: Supply and erection of 125 Amps capacity floor mounting panel board (Cubical type) with bus bar chamber (Incoming 1 No. 125 A TPN MCCB, Bus Bar: 125 Amps 3 phase 4 wire Copper Bus Bar, Outgoing 8 Nos. 63 A TPN fixed type MCCB)

A112: Design, fabrication, supply and erection of following sub switch boards cubical type floor mounting arrangement made out of MS sheet steel enclosure with bus bar chamber and suitable size copper busbar, cable chamber, interconnection, wiring, painting.

A113: Supply & run of 4 x 6 Sq.mm of PVC insulated unsheethed single core FRLS copper cable of 1100 V grade in suitable PVC rigid pipes to be concealed in wall with continous earth connection by 1 run of 2.5 Sq.mm PVC insulated unsheathed copper FRLS cable of 1100 V grade from panel to lighting DBs in stilt floor and also to the lighting DB's near the floor panel in all the floors located near the floor panel itself

A114: Supply & run of 4 x 10 Sq.mm of PVC insulated unsheethed single core FRLS copper cable of 1100 V grade partly in new PVC rigid pipes to be concealed in wall and ceiling with continous earth connection by 1 run of 2.5 Sq.mm PVC insulated unsheathed copper FRLS cable of 1100 V grade from panel to power DB located near the panel itself- From floor panel to near by PDB in 3 floors

A115: Wiring for lift well light point and socket outlet with 2 x 1.5 sqmm FRLS PVC

A116: Supply and fixing of Water Tight bulk head fitting suitable for 60W incandescent lamp with guard.

A117: Supply and fixing of AC / DC 76 mm Buzzer / call bell suitable for 230 vplts 50 c / s single phase AC supply on suitable TW Board with push switch

A118: Supplying, Fixing and testing and commissioning of MCCB / MCB / Isolator 40 A TPN 10 KA MCB

A119: Supplying, Fixing and testing and commissioning of MCCB / MCB / Isolator 10/20/32A DP MCB

A120: Supplying, Fixing and testing and commissioning of MCCB / MCB / Isolator 63A TPN MCB

A121: Supply and fixing of perforated cable trays of sizes without cover as given below made out of 14 SWG CRCA sheet steel

A122: Supply and fixing of perforated cable trays of sizes with cover as given below made out of 14 SWG CRCA

A123: Supply and fixing of MS cable box of suitable size on wall for the entry of 4 C x 16 sqm / 3.5 C x 25 sqm

A124: Supply and fixing of triple pole and neutral four way 7 segment 3 tier compartmental type MCB distribution board complete with the following and necessary neutral link, earth connector link etc. with bus bar and double door arrangements on surface / in flush with wall and making good Incoming - 1 No Outgoing - 12 Nos

A125: Providing Sthapathy Kambu, Kabothagam,Navadai and Kodipalai at Top of the SunShade ,Kalvarkanam at Bottom of the Sunshade, Kambu, Eluthagam and Navadai at Bottom of the sill slab Work for Front side elevation windows for the Combined 2 nos of W- 0.90x 1.650 window with Center pillar in Third and Terrace Floor etc.,

A126: Providing Sthapathy Kambu, Kabothagam,Navadai and Kodipalai at Top of the SunShade ,Kalvarkanam at Bottom of the Sunshade Work for Front side elevation windows for Combined 2 nos of W- 0.90x 1.650 window with Center pillar in Second Floor etc.,

A127: Providing Sthapathy Kambu, Kabothagam,Navadai and Kodipalai at Top of the SunShade ,Kalvarkanam at Bottom of the Sunshade, Kambu, Eluthagam and Navadai at Bottom of the sill slab Work for Front side elevation windows size 2.70X1.65 m in Second and Third Floor etc.,

A128: Providing Sthapathy Kambu, Kabothagam,Navadai and Kodipalai at Top of the SunShade ,Kalvarkanam at Bottom of the Sunshade, Kambu, Eluthagam and Navadai at Bottom of the sill slab Work for Front side elevation windows size 2.70X1.65m in Stilt and First Floor etc.,

A129: Providing Sthapathy Kambu, Kabothagam,Navadai and Kodipalai at Top of the SunShade ,Kalvarkanam at Bottom of the Sunshade Work for Front side elevation Combined windows for the 2 nos of W- 0.90x 1.650 window with Center pillar in Second and Third Floor etc.,

A130: Providing Sthapathy Kambu, Kabothagam,Navadai and Kodipalai at Top of the SunShade ,Kalvarkanam at Bottom of the Sunshade, Kambu, Eluthagam and Navadai at Bottom of the sill slab Work for Front side elevation Combined windows for the 2 nos of W- 0.90x 1.650 window with Center pillar in First Floor etc.,

A131: Providing Sthapathy Kambu, Kabothagam,Navadai and Kodipalai at Top of the SunShade ,Kalvarkanam at Bottom of the Sunshade Work for Front side elevation Combined windows for the 2 nos of W- 0.90x 1.650 window with Center pillar in Stilt Floor etc.,

A132: Providing Sthapathy Kambu, Kabothagam,Navadai and Kodipalai at Top of the SunShade ,Kalvarkanam at Bottom of the Sunshade, Kambu, Eluthagam and Navadai at Bottom of the sill slab Work for Front side elevation Combined windows for the 2 nos of W- 0.90x 1.650 window with Center pillar in Stilt and First Floor etc.,

A133: Providing Sthapathy Cornice Work for Side Staircase Head Room Front side Design at Parapet Level etc.,

A134: Providing Sthapathy Cornice, Bothiyal, Piller Design at Top Box Design at Bottom Work for Round Column Stilt to First Floor at Center Portico etc.,

A135: Providing Sthapathy Cornice, Bothiyal, Piller Design at Top Box Design at Bottom Work for Round Column Stilt to First Floor at roof at Side Portico etc.,

A136: Providing Sthapathy Cornice Bothiyal, Piller Design at Top,Box Design at Bottom Work for Pillar First Floor to Head Room roof at Center Portico etc.,

A137: Providing Sthapathy Cornice, Bothiyal, Piller Design at Top,Box Work for Pillar StIlt Floor to Third Floor roof at Center Portico etc.,

A138: Providing Sthapathy Cornice Work for Ground Floor Roof Projection Kabothaga Border Work 6" etc.,

A139: Providing Sthapathy design Work for Portico Kodungai in First Floor roof at Center Portico etc.,

A140: Providing Sthapathy design Work for Portico Kodungai in First Floor roof at Side Portico etc.,

A141: Providing Sthapathy Cornice Work for Parapet in First Floor Roof Projection Kabothaga Border Work 9" etc.,

A142: Providing Sthapathy Cornice Work for Parapet in Third Floor Roof Projection Kabothaga Border Work 9" etc.,

A143: Providing Sthapathy design Work for Kodungai in Center Head Room etc.,

A144: Providing Sthapathy design Work for Kodungai in Side Head Room etc.,

A145: Providing Sthapathy design Work for Kodungai Middle Portion in Third Floor roof etc.,

A146: Providing Sthapathy design Work for Parapet Top Butten with Bell etc.,

A147: Providing Sthapathy design Work for Additional Piller Projection 5" Staircase Portico to Head Room etc.,

A148: Providing and fixing 25mm x 6mm copper strip on surface or in recess for connections as required for alternator neutral

A149: Drilling of 6" dia (150mm) Vertical Borewell in Overburden Soil

A150: Drilling of 6" dia (150mm) Vertical Borewell in hard rock

A151: Supply and delivery of 160mm dia outer dia casing pipe 6 kg/sq.cm

A152: Supply and fixing of 160mm dia PVC End cap for bore well

A153: Supply and delivery of wet type lubricated 3 Phase 7.50 HP submersible pump set. Duty lpm x m = 50 x 225.

A154: Supply and delivery of 5 HP openwell submersible pumpset. The motor should be confirming pump and motor HP rating should be specified Duty lpm x m = 50 x 100.

A155: Labour charges for erection of submersible pumpset in borewell / openwell etc., all complete. a) Up to 5 HP

b) Above 5 HP to 10 HP

A156: Supply and delivery of Three phase panel Board with two level guard auto start with ISI mark for single phase wall mounted type with ammeter, Voltmeter, Indicating lamps ON/OFF push bottons etc., Upto 5 HP

A157: Supply and delivery of Three phase panel Board with two level guard auto start with ISI mark for single phase wall mounted type with ammeter, Voltmeter, Indicating lamps ON/OFF push bottons etc., Up to 7.5 HP

A158: Supply and delivery 3 core of 4 sqmm Flat type coper cable

A159: Supply and delivery of 20mm dia Nylon rope of best and approved quality for tying the delivery line with submersible pumpset for safety measure etc., all complete.

A160: Supply and laying of following dia UPVC Pipe a) 50 mm dia Column Pipe

A161: Supply and clamping of the following sizes of PVC / XLPE Aluminium Armoured LTUG cable (AGL) a) 3.5 C x 70 sqmm aluminium cable

b) 3.5 C x 25 sqmm aluminium cable

c) 4 C x 16 sqmm aluminium cable

d) 4 C x 10 sqmm aluminium cable

e) 2 C x 10 sqmm aluminium cable

A162: Supply and laying of PVC, aluminium conductor 1.1KV grade armoured ,MV cable (BGL) a) 3.5C x 120 sq mm aluminium cable

A163: Supply and fixing of brass cable gland for XLPE armoured LTUG cable for following sizes with earth connection. a) 3.5 C x 120 sqmm aluminium cable gland

b) 3.5 C x 70 sqmm aluminium cable gland

c) 3.5 C x 25 sqmm aluminium cable gland

d) 4 C x 16 sqmm aluminium cable gland

e) 4 C x 10 sqmm aluminium cable gland

f) 2 C x 10 sqmm aluminium cable gland

A164: Supply and providing cable end termination of following sizes of PVC armoured LTUG Aluminium cable a) 3.5 C x 120 sqmm aluminium cable end termination

b) 3.5 C x 70 sq.mm aluminium cable end termination

c) 3.5 C x 25 sqmm aluminium cable end termination

d) 4 C x 16 sqmm aluminium cable end termination

e) 4 C x 10 sqmm aluminium cable end termination

f) 2 C x 10 sqmm aluminium cable end termination

A165: Supply and fabrication of two wheeler shed truss work by using MS pipe 6'' dia 3.4mm thick vertical post etc.

A166: Supply and delivery, fixing of 0.47mm Galvanium sheet roof of approved quality

A167: Geophysical investigation charges under deposit works per point.

A168: Supplying and fixing of Surface round Fitting Light 18W LED with fittings.

A169: Supplying and fixing of Floating Light 100W LED with fittings.

A170: Supplying and fixing of Focus light 500 Watts

A171: Hire charges for deploying earth moving machinery (JCB/Poclain) for earthwork

A172: Purchase fuel ( Diesel) and filled the new generator etc

A173: Supplying and fixing of 20 amps single pole MCB inculding necessary fittings.

A174: Supplying and fixing of MS Box of size 100x100x75mm including cover cost of all materials

A175: Supply and delivery 2 core 10 sqmm Aluminium aroumd LTUG Cable

A176: Labour charges for conveying and laying of LTUG cable in Below ground level

A177: Charges for conveying and fixing of UG cables of size 4 to 25mm of 2, 3, 3.5, 4 core cable in above ground level

A178: Towards fabrication supply and installation of CT metering box for availing the power supply from TANGEDCO

A179: Lioson charges for CEIG approved for 160 KVA genset in all etc

SRP CONSTRUCTION COMPANY

K BASKARAN