138WE/L-159/2025-26

Amount

Demolition of cement concrete (un reinforced) in ground floors and pavings not exc 15 cm thick (below or above ground level) and removing debris off the premises complete all as specified and/or as directed by Engr-in-Charge.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for and removing debris off the premises, complete all as specified and/or as directed by Engr-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but including backing), removing rubbish off the premises complete all as specified and/or as directed by Engr-in-Charge.

Dismantling wall and ceiling boards (Fiber, pulp, insulation, blankets) etc. any thickness including covered fillets and supporting members, complete all as specified and/or directed by Engr-in-Charge.

Dismantling unframed wooden fillets, rails, posts, rafters, purlins, grids for ceiling & wall panelling etc. under 40 sqcm in section, complete all as specified and/or directed by Engr-in-Charge.

Demolition of precast concrete block walling built in cement mortar including all quoins, arches, pillars etc. complete all as specified and/or directed by Engr-in-Charge.

Taking down cement plaster on brick/PCC block or concrete surfaces including racking out joints, hacking for key, scrubbing down with water etc., complete all as specified and/or as directed by Engr-in-Charge.

Taking down chowkat or frame with shutters (without taking of shutters from the frame) not exc 1.5 sqm each any type of door (wooden, aluminium & steel etc.) complete all as specified and/or as directed by Engr-in-Charge.

Taking down chowkat or frame with shutters (without taking of shutters from the frame) exc 1.5 sqm each but not exc 4 sqm each any type of door (wooden, aluminium & steel etc.) complete all as specified and/or as directed by Engr-in-Charge.

Taking down shutters of any description exceeding 1.00 Sq.m but not exceeding 2.00 Sq.m each, from chowkhat complete all as specified and as directed by the Engineer-in-Charge.

All as per Srl item No 10 above, but not exceeding 1.00 Sqm in size.

Hacking out old broken glass (any thickness, size, quality or description) from wooden panes or stone, concrete or brick surrounds, glazed with oil putty or fixed with beads complete all as specified and/or directed by Engr-in-Charge.

Dismantling plain or corrugated steel sheeting any gauge or thickness including nanital or similar pattern complete all as specified and as directed by Engr-in-Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for angle iron or flat iron as in post and guard bars or grating, complete all as specified and/or directed by Engr-in-Charge.

M&L for 9mm thick prelaminated particle board medium interior grade, prelaminated one side with decorated choice lamination & other side balancing white lamination fixed with nails to timber frame work as in wall panelling, shelves/boarding complete all as specified and as directed.

M&L for 9mm thick prelaminated particle board medium interior grade, prelaminated one side with decorated choice lamination & other side balancing white lamination fixed with nails to timber frame work as in ceiling panelling, complete all as specified and as directed.

M&L for 2nd class soft wood clean sawn as in battens for grids of ceiling & lining fixed with nails exc 13 sqcm and not exc 25 sqcm in section, complete all as specified and directed by Engr-in-Charge

M&L for 2nd class soft wood clean sawn as in battens for grids of ceiling & lining fixed with nails exc 6 sqcm and not exc 13 sqcm in section, complete all as specified and/or as directed by Engr-in-Charge.

M&L for covered fillets of standard hard board not less than 6mm thick and up to 40mm wide and fixing with screws complete all as specified and/or as directed by Engr-in-Charge.

M&L for 75 mm thick PCC 1:3:6 type C-2 (using 20mm graded aggregate) as plinth protection finished even and smooth with out using extra cement, complete all as specified and/or as directed by Engr-in-Charge.

M&L Forming Contraction (Dummy) joints 65 mm deep x 10mm wide, filled with sealing compound Grade 'A' in plinth protection, complete all as specified and/or as directed by Engr-in-Charge.

M&L for PCC 1:4:8, type D2 (using 40mm graded crushed aggregate) as in mass concrete and filling of foundation, complete all as specified and/or as directed by Engr-in-Charge.

Demolition of reinforced cement concrete of any description and position not otherwise specifically provided for.

M&L for reinforced cement concrete (Nominal Mix) 1:2:4 type B1 (20mm graded aggregate) as in slabs supported of walls, beams and columns in floors, roofs, landings, balconices, canopies, deck slabs and in shelves etc. complete all as specified and/or as directed by Engr-in-Charge.

M&L for precast cement concrete 1:2:4 type B1 (20mm graded aggregate) in landings, cover slabs (for manholes etc.), chullah hoods, chhajja, water troughs, shelves and similar articles with plain faces, set in CM 1:6, complete all as specified and/or as directed by Engr-in-Charge.

M&L for form work to soffits of suspended slabs flat type such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick (Horizontal or slopping etc. complete all as specified and/or as directed by Engr-in-Charge.

M&L mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and/or as directed by Engr-in-Charge.

M&L for hardcore of broken stone gauge nexc 63mm , deposited, spread and levelled in layers not exc. 15cm thick watered and rammed to a true surface. complete all as specified and as directed.

S&F rolled section as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guide, for sliding doors fixed with angle cleats or other connecting plates Fe -410 Gde E-250 Quality-A, complete all as specified and/or directed by Engr-in-Charge.

Preparation of new/ previous untreated corrugated steel surface of any description over 10cm grith or width, not otherwise described with one coat of red oxide zinc chrome primer followed by two coats of synthetic enamel paint complete all as specified and directed.

M&L precast solid blocks in cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) as in block masonry, exc.10cm in width and set in cement mortar 1:6, complete all as specified and/or directed by Engr-in-Charge.

M&L for 10mm thick rendering on fair faces of block/ brick wall works finished even and smooth without using extra cement in cement mortar 1:6 complete all as specified and/or directed by Engr-in-Charge.

M&L for 15mm thick rendering on other than fair faces of brick works finished even and smooth without using extra cement in cement mortar 1: 4 including mixing of liquid water proofing compound as per manufacturer's instructions complete all as specified and as directed by Engineer-in-Charge. Note : WPC will be measured and paid separately.

Supply only integral liquid water proofing compound. Make : Pidilite/Sika/Asian paints.

M&L for preparation of new plastered wall surface of any description and applying two coats of cement based paint over a coat of primer complete all as specified and/or as directed by Engr-in-Charge.

M&L preparing newly plastered wall surfaces and applying two coats of distemper oil emulsion including priming plastered and other surfaces with alkali resistant priming paint, complete all as specified and as directed.

S&F 35mm thick 2nd class hard wood plain framed panelled shutters (any number of panels) with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, complete all as specified and/or as directed by Engr-in-Charge.

S&F Powder coated (minimum thickness of powder coating 50 micron) anodised aluminium frames for door, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and/or as directed by the Engr-in-Charge.

M&L for powder coated aluminium door shuttlers, aluminium sections weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws, hinge type B-21 100 mm long (3 Nos) suitable handle (2 Nos), complete all as specified and/or as directed by Engr-in-Charge. Note : Glass / Wiremesh be measured seperately.

S&F anodised aluminium window and ventilator shutters, including aluminium jali fixed in one side, side hung type without sash, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading screws, anodised aluminium fittings such as peg stays 150mm long (1 No) hinges type B-21 100mm long (2 Nos) suitable handle (1 No) etc. complete all as specified and/or as directed by Engr-in-Charge. Note : Glass / Wiremesh be measured seperately.

S&F anodised aluminium window and ventilator shutters, fixed type without sash, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading screws, anodised aluminium fittings complete all as specified. Note : Glass / Wiremesh be measured seperately.

S&F 2nd class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and/or as directed by the Engr-in-Charge.

S&F 2nd class hard wood 30 mm thick Glazed and Skelton shutter, open and prepared to receive the glass, gauze etc. (without sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc., complete all as specified and/or as directed by Engr-in-Charge. Note : Glass / Wiremesh be measured seperately.

M&L for preparation of new untreated wood or wooden based surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and/or as directed by Engr-in-Charge.

M&L sheet glass 3mm thick ordinary quality and glazing with oil putty or wooden beads in square not exc. 0.50 sqm in each pane complete all as specified and/or as directed by Engr-in-Charge.

M&L sheet glass 5.5mm thick ordinary quality and glazing with oil putty or wooden beads in square not exc. 0.50 sqm in each pane complete all as specified and as directed.

S&F Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples, complete all as specified and/or as directed by Engr-in-Charge.

S&F in repairs Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples, complete all as specified and/or as directed by Engr-in-Charge.

S&F 150mm long aluminium anodized, barrel tower bolt of extruded section complete all as specified and/or as directed by Engr-in-Charge.

S&F 100mm long aluminium anodized, barrel tower bolt of extruded section, complete all as specified and/or as directed by Engr-in-Charge.

S&F 150mm size extruded aluminium alloy handles, fabricated type, anodized complete all as specified and/or as directed by Engr-in-Charge.

S&F 100 mm size extruded aluminium alloy handles, fabricated type, anodized, complete all as specified and/or as directed by Engr-in-Charge.

S&F in repair aluminium (die cast) body door closer hydraulically designation No 3 universal type suitable for door shutter of 851 to1000mm in width and weight 61 to 80 kg complete all as specified and/or as directed by Engr-in-Charge.

S&F floor door stopper (length of cover plate) 150mm long aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floor complete all as specified and/or as directed by Engr-in-Charge.

S&F 75mm long aluminium anodized, butt hinges of extruded section type C-21, complete all as specified and/or as directed by Engr-in-Charge.

S&F 100mm long aluminium anodized, butt hinges of extruded section type B-21, complete all as specified and/or as directed by Engr-in-Charge.

S&F 250mm long aluminium alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy fixed complete all as specified and/or as directed by Engr-in-Charge.

M&L for 25 mm thick PCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in sub base of floor complete all as specified and/or as directed by Engr-in-Charge.

M&L for joint free non-skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11 sqm but not exc. 0.18 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in CM 1:4 complete all as specified and/or as directed by Engr-in-Charge.

M&L for Non - skid coloured Ceramic joint free tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exc. 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and/or as directed by Engr-in-Charge.

M&L for 20 mm thick granite stone (any type) (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of granite including cutting etc. and screed bed with CM (1:4) 15mm thick for laying floor tiles complete all as specified and/or as directed by Engr-in-Charge.

M&L for glazed ceramic coloured tiles in vertical surfaces of size 450x350x7mm/ 350x250x7mm thick set and jointed in neat cement slurry and pointed with white or coloured cement to match over and including rendering 10 mm thick in cement mortar (1:4) as in backing coat complete all as specified and/or as directed by Engr-in-Charge.

M&L for dismantling water tanks exc 250 but not exc 500 Litres, and removing to store, complete, all as specified and as directed by the Engineer-in-Charge.

S&F tripple layered rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 500 litres including all accessories, complete all as specified and/or as directed by Engr-in-Charge.

S&F in repairs 25mm bore stop valve chromium plated screw down under high pressure with crutch or butter fly handle screwed both ends for iron pipe or brass ferrule, complete all as specified and as directed.

S&F in repairs 25mm ball brass valves, high pressure with polythene float and fly nut complete screwed for iron/PPR, complete all as specified and as directed.

S&F in repairs Towel Hanger with 6 Nos of pin and 600mm long chromium plated etc. complete all as specified and/or as directed by Engr-in-Charge.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and/or directed by Engr-in-Charge.

S&F Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and/or directed by Engr-in-Charge.

All as per Srl item No 68 above, but except sheeting.

M&L for preparation of old painted steel sheets of any description and applying two coats of synthetic enamel paint complete all as specified and/or directed by Engr-in-Charge.

S&F in repair 19mm dia mild steel, chromium plated curtain rods, with brackets, end bulbs complete all as specified and/or directed by Engr-in-Charge.

S&F vitreous china urinal half stall type, white complete including providing and fixing plugs, bedding urinal against wall in CM 1:2 securing urinal to plugs with and including 60 mm brass screws, pointing around urinal back in cement, fixing grating and union for discharge pipe excluding flushing cistern, flush pipe but including CP waste coupling, PTMT urinal spreader, etc. complete all as specified and as directed by the Engr-in-Charge.

S&F in repair Vitreous China wash basin fancy type pedestal pattern, white, flat back, size 550 x 400mm including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe, complete all as specified and/or directed by Engr-in-Charge.

S&F Vitreous china wash basin white flat back size 550 x 400 mm including including CI brackets of irons 65 x 65 x 6mm embedded in PCC block with PCC 1:2:4 type B-1 & CP grating with holes fixed in repairs complete all as specified and directed by Engr-in-Charge.

S&F in repair 15 mm bore pillar taps, fancy type cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe.

S&F in repairs health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed by Engr-in-Charge.

S&F sheet glass basin shelf assembly consisting of 8mm thick glass shelf 600 x 150mm wide with bevelled edges/hatching of edges fixed with stainless steel 'D' bracket fixed and railing complete all as specified and directed.

S&F soap dish, any type, fixed to plugs with chromium plated brass screws completed all as specified and directed.

Supply only 32mm waste coupling of PTMT for sink and wash hand basin (Half or full threaded ) (Minimum Weight 45 grams), complete all as specified and/or directed by Engr-in-Charge.

S&F CP toilet jet spary ABS with double lock 1.2 mtr CP tube stainless steel flexible hose complete all as specified and/or directed by Engr-in-Charge.

S&F sheet glass shelf assembly consisting of 5.5mm thick glass shelf 12 cm wide with chromium plated bracket gourd and railing 60 cm long, complete all as specified and/or directed by Engr-in-Charge.

S&F in repair towel rod brass CP 60 cm long between flanges and including all accessories like brackets/ screws etc as recommended by manufacturer and complete fixed in position complete all as specified and/or directed by Engr-in-Charge.

S&F in repair grating doom 100mm dia of PTMT (min weight 25gms) complete all as specified and/or directed by Engr-in-Charge.

S&F in repairs 15mm bore stop cock fancy type chromium plated cast copper alloy screw down under high pressure screwed both ends for iron pipe or brass ferrule, complete all as specified and/or directed by Engr-in-Charge.

S&F in repairs vitreous China squatting pan or Orissa pattern 580 x 440 mm white with integral foot rest (excluding cistern) with front or back inlet ant pattern as in repairs including bedding with PCC 1:2:4, type B-I (using 20 mm graded crushed stone aggregate) complete all as specified and/or directed by Engr-in-Charge.

S&F in repairs vitreous China wash down water closet (pedestal), white (EWC) including plastic sheet cover of same colour of WC, closed pattern with flat bottom and cover and mild steel chromium plated hinging device complete all as specified and/or directed by Engr-in-Charge.

S&F flushing cistern of PVC 10 ltr. cap. with dual flushing system, white colour, valveless symphonic action type, low level, with inlet, ball valve, float and including brackets and connection to pipe etc. incl all necessary accessories like rag bolts/ gel gasket etc as recommended by manufacturer for fixing, packing complete all as specified and/or directed by Engr-in-Charge.

S&F in repairs 15mm dia angle stop valves, fancy type chromium plated with long shank and cast copper alloy (concealed type), screwed down high pressure screwed both ends for iron pipes complete all as specified and/or directed by Engr-in-Charge.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories), complete all as specified and/or directed by Engr-in-Charge.

M&L for PVC (SWR) pipe single socketed, 110mm soil, waste and rain water drainage pipes laid in trenches and jointed complete all as specified and/or directed by Engr-in-Charge.

M&L for PVC (SWR) pipe single socketed, 110mm soil, waste and rain water drainage pipes fixed with wall and jointed complete all as specified and/or directed by Engr-in-Charge.

S&F in PVC (HDPE) SWR 75 mm bore, single socketed in any length with rubber ring joints using solvent as per manufacture instruction, laid in trenches or in floors complete all as specified and directed by Engr-in-Charge.

S&F PVC (SWR) vent cowl of 75mm bore, complete all as specified and as directed.

S&F 110 mm dia PVC (SWR) bend any radius, complete all as specified and as directed.

M&L for PCC 1:4:8, type D-2 (using 40mm graded stone aggerate) bed to drain pipe incl packing under and haunching against side after they are laid and tested up to 110mm dia pipe, complete all as specified and/or directed by Engr-in-Charge.

M&L for Cast iron Nahani trap 75mm with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and as directed.

Taking up or down 25 mm to 32mm bore steel tubing and connections and set aside for re-use or removal to store, complete all as specified and/or directed by Engr-in-Charge.

S&F 25mm dia 3 layer PP-R polypropylene random copolymer concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete all as per manufacture instructions and as directed by Engr-in-Charge.

S&F 32mm dia 3 layer PP-R polypropylene random copolymer concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete all as per manufacture instructions and as directed by Engr-in-Charge.

S&F in repairs fancy type 15 mm bore chromium plated bib taps, cast copper alloy, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and as directed.

S&F in repairs, 15mm bore, PVC connection pipe 600 mm long with PTMT nuts at both ends, complete all as specified and as directed.

S&F in repairs, 750mm long, 32/40mm dia, PVC flexible waste pipe for sink/wash hand basin complete all as specified and as directed.

S&F vitreous chainaware, coloured, urinal partition of size 310 x 700 mm fixed to wall with plugs and chromium plated screws complete all as specified and as directed by the Engineer-in-Charge.

Taking down carefully copper/aluminium point wiring (light, fan, socket and power point) including complete fittings such as switches, ceiling rose, regulators, socket etc. and removing material from site and making good disturbed surfaces of walls, floors/ceiling to match the existing surface all as specified and directed by Engr-in-Charge.

Point wiring complete with 1.5 sqmm nominal area of copper conductor multi stranded PVC insulated and unsheathed 1100 volts cable drawn through & including PVC casing & caping with standard accessories such as elbows, tees, junctions etc. and PVC moulded terminal box with top cover of including PVC insulated unsheathed solid 1.5 sqmm copper conductor cable as continuous earth lead complete all as specified and/or directed by Engr-in-Charge for the followings:-

One light/exhaust fan point controlled by one way switch.

One switch socket outlet 6 Amps, 230 volts point on same board.

One switch socket outlet 6 Amps, 230 volts point on independent board.

All as per Srl item No 108 above, but using cables 4 Sq mm size.

S&F switch piano flush button single pole 6 Amps 230 volts one way complete all as specified and/or directed by Engr-in-Charge.

S&F socket outlet two in one 6 Amps flush type.230 volts complete all as specified and/or directed by Engr-in-Charge.

S&F switch Socket combination outlet multi purpose 5 pin 6 Amps and 16 Amps 230 volts complete all as specified and/or directed by Engr-in-Charge.

S&F ceiling rose, surface Bakelite three terminals complete all as specified and/or directed by Engr-in-Charge.

S&F in replacement of sheet metal enclosure for DBs double door when MCB's to be used single pole & neutral 240 Volts 12 Ways complete all as specified and/or directed by Engr-in-Charge.

S&F in replacement of sheet metal enclosure for DBs double door when MCB's to be used single pole & neutral 240 Volts 08 Ways complete all as specified and/or directed by Engr-in-Charge.

S&F MCB SPN 63 Amp 240 Volts AC ISI marked complete all as specified and/or directed by Engr-in-Charge.

S&F MCB SP 6-32 Amps. 240 Volts 50 HZ complete all as specified and/or directed by Engr-in-Charge.

Supply and fix in replacement LED light fitting 1X20 W, 220 V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and/or directed by Engr-in-Charge. Make-Havells /Crompton/ Bajaj.

S&F LED luminaire 600 x 600 mm, 36 watt, 220 volt AC surface / recessed type with high efficiency PMMA difuser soft glair free light complete with driver, holders and LED lamp suitable for roof ceiling including connecting up with driver 3 core flexible copper conductor cases of suitable size complete all as specified and directed.

S&F in replacement LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and/or directed by Engr-in-Charge.

M&L for submain wiring along with earth wire with the following sizes of FRLSH PVC insulated copper conductor, single core cable in surface/recessed as required in PVC casing caping wire size 2x10 sqmm + 1x10 sqmm earth wire including taking down complete all as specified and/or directed by Engr-in-Charge.

Supply and laying in replacement of XLPE insulated, aroured, heavy duty electric cables, with stranded aluminium copper conductor rating 1100 volts grading of size 25 sqmm 2 core laid in trenches or passing through pipes, ducts or fixed to walls / poles, complete all as specified and/or directed by Engr-in-Charge.

M&L for Earthing complete with galvanised steel earth plate electrode 60 cm X 60 cm X 6 mm thick, buried directly in ground (earth pit not less than 2.25 meter deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level, connected to and including 4 mm dia GI wire as earthing lead, by means of bolts, nuts, check nuts and washers of galvanised iron all as shown in electrical plate No 3 of MES SSR Part I and testing on completion including excavation and earth work in any type of soil, PCC (1:3:6) type C1 chamber, MS frame and cover 6 mm thick in cement concrete (1:2:4) type B1 reinforced with welded steel wire fabric or XPM (weight not less than 4 Kg per Sqm) with cast iron frame, funnel with wire mesh, GI watering pipe 20mm dia medium grade and lugs complete all as specified and/or as directed by Engr-in-Charge.

RANA ENTERPRISES (BID ID -3420502)

M/S HONY CAPT RIGZIN SAMPHEL (BID ID -3420599)