Construction of Group House from 5 to 8 in Srilankan Refugees Camp at Virupatchi village, Virupatchi Panchayat in Odddanchatram Block of Dindigul District Each house Rs.27.50 lakhs

Amount

Part 1 :Construction of Group House from 5 to 8 in Srilankan Refugees Camp at Virupatchi village, Virupatchi Panchayat in Odddanchatram Block of Dindigul District Estimate Amount Rs.110.00 Lakhs ( Each house Rs.27.50 lakhs)

Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

Supplying and filling in foundation, basement, etc with filling M.Sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Cement Concrete 1:4:8 (One Cement, Four sand and Eight hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Refilling with excavated earth other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officers in layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification

Brick work in Cement Mortar1:5 (one cement and five sand) using best quality of country bricks of size 8-3/4" x 4-1/4" x 2-1/4" for foundation and basement including curing, etc., complete complying with standard specifiction.

Foundation and basement

Superstructure

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton

Below Ground level

Above ground level

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification.

Reinforced Cement Concrete 1:1.5:3 (One Cement, One and a half sand and Three hard broken stone jelly) using 20 mm gauge hard broken granite stone jelly for all RCC items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc. and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers

Below Ground level

Above ground level

Supplying and applying of two coats of putty of 3mm thick over the exposed RCC surface of ceiling including finishing the joints smoothy with grinding machine and the surface shall be thoroughly cleaned out of dust and scrubbing. The Surface shall then be allowed to dry for atleast 48 hours. It shall then be sand papered (waterproof abrasive sheet) to give a smooth and even surface. Any unevenness shall be made good by applying 1st coat of putty mixed with water on the entire surface including filling up the undulations and applying 2nd coat of putty after 6 hours of 1st coat of putty and then sand papering (waterproof abrasive sheet) the same after it is dry and finishing the surface smoothly, etc., complete complying with standard specifications and as directed by the Departmental Officers. [ The rates are inclusive of hire charges for grinding machine with wheel, cost of sand paper (waterproof abrasive sheet), cost of putty blade, labour charges for grinding the joints and sand papering, two coat of putty, scrapping the putty area to level the surface smooth, etc., complete]. The Putty shoule be got approved by the Executive Engineer before use on work.

Special ceiling Plastering with cement mortar 1:3 mix to 10mm thick including cost and conveyance of all materials & all labour charges etc., complete.

Plastering with Cement Mortar 1:5 (One cement and Five sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Providing weathering course with best quality of broken jelly of size 20mm uniform gauge in pure slacked lime (no sand to be used) over the roof slab in the proportion of brickjelly lime 32:121/2 by volume and laid over in a single layer and consolidated

Finishing the top of roof with one course of machine pressed tiles of size 200mm x 200mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Paving Floor with scratch proof ceramic tiles of any colour of size 305 x 305 x 6mm, laid in C.M 1:3 mix 20 mm thick & pointing with colour cement using 0.40kg per sq.m including cost & conveyance of all materials to site and all labour charges etc.complete

Providing granolithic floor finish of the following thickness with plain cement concrete 1:2:4 (One Cement, Two sand and Four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers.

White washing two coats with freshly burnt white shell lime in all floors including cost of lime, blue powder fevicol type gum, brushes, scaffolding charges, etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and painting the walls with two coats of Oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the walls smooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification.

Painting two coats of newly plastered wall surface with ready mixed plastic Exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting two coats with enamel paint over new iron work including cost & conveyance of all materials to site and all labour charges etc., complete.

Fabrication and supply & Delivery of MILD STEEL DOORS of the following Size with Double Leaf outer frame made of 35x35x5 mm equal M.S.L angle and shutter frame made of 25x25x5mm equal M.S L angle for Horizontal and Vertical members and the shutter frame strengthened by stiffeners of 2 Nos horizontal, 3 Nos. diagonal for each shutter using MS flat of size 20x5mm fully covered with 18 gauge plain M.S full sheet welded with shutter frame neatly and also fixing by welding 6 Nos. of hold fasts made of 35x35x5 mm equal M.S L angle, 2 Nos. of wind appliances, 3 Nos. of tower bolts,1 No aldrop, 3 Nos. of handles fixing the shutter with 6 Nos. of 6 inch hinges with outer frame of the door including painting the whole unit with one coat of best quality of red oxide primer for Group house

(MD) MS Door of size 0.90 x 2.10m

(D) MS Door of size 0.90 x 2.10m

Solid PVC Door shutter with frame using 19 gauge 19mm MS sq. tubes for styles and outer frames, 15mm MS sq. tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for paneling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm, with suitable rabate for housing the shutter.

(D1) PVC Door of Size 0.75 x 1.80m

Fabrication and supply of MILD STEEL WINDOW of of the following size with Double Leaves outer frame made of 35x35x5 mm equal M.S.L angle, mullion section made of 25x25x5mm equal T section, Shutter Frame made of 25 x 25 x 5mm equal M.S.L angle for Horizontal and Vertical members and the shutter frame strengthened by stiffeners of 2 No. Horizontal for each shutter using 25 x 25 x 5mm equal M.S. T section fully covered with 18 gauge plain M.S full sheet welded with shutter frame neatly and also fixing by welding protective grill with 12mm square M.S rods at an interval of not greater than 10cm centre to centre to the outer frame,4 Nos. of hold fasts made of 35x35x5 mm equal M.S.L angle , 2 Nos. of peg stays with holes for keeping the windows open in different positions, 2 Nos. of locking handles, fixing the shutter with 4 Nos. of 4 inch hinges with outer frame of the window including painting the whole unit with one coat of best quality of red oxide primer for Group house

(W) MS window of size 0.90m x 1.20m

(W1) MS window of size 0.90m x 0.60m

Towards the cost of labour charges for fixing new steel door and window in position including all labour charges etc.,complete

RCC Jally of size 0.60m x 0.45m

Labour charges for fixing of Doors ,windows and RCC Jally in position including all labour charges etc.,complete

Steel doors with alongwith frame

Steel windows and Ventilator with alongwith frame

Supply and fixing in position best approved quality and make white glazed earthen ware oriya type Indian water closet of size 580 mm with P or S trap embedding the closest and trap to shape in position with brick jelly lime concrete 1:2:5 (one lime two sand and five brick jelly) using 40 mm broken brick jelly and finishing the top to required slope and including giving connections to the PVC soil stacks using 0.60 m long PVC Pipe 110 mm dia. 6 kg/sqcm by dismantling masonry, RCC roof or floor slaps and making good, the disturbed portion to original condition without and leakage etc. complete as directed by the departmental officers and complying with standard specifications

White Porcelain Sink of size 600mm x 450mm x 200mm with 32mm dia ‘B’ Class GI Waste Water Pipe and 32mm dia CP Waste Coupling including cost and conveyance and all labour charges etc.,complete

Provision for Electrification

Wiring with 2 x 1.5 sq.m (22/0.3) PVC insulated unsheathed SC Cu. Conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with TW switch box in flush with wall covered with hylum sheet of 3mm thick with painting of suitable colour for open PVC light point/fan point(for electronic regulator) - S.D.No: 17

Wiring with 2 x 1.5 sq.m (22/0.3) PVC insulated unsheathed SC Cu. Conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories and with 150 x 100 x 113 TW switch box for 5A 3pin non inter locking CS plug with painting of suitable colour with continuos earth wire connection of 14 SWG TC wire for open PVC plug - S.D.No: 37

Supply and fixing of 1200mm (48") AC ceiling fan with stepped electronic 300 W regulator with 1 meter down rod on the existing clamp. - S.D.no: 107

Supply and run of 2 of 1.50 sq.mm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100 V on 7/20 GI bearer wire for service connection mains. - S.D.No: 64

Supply and run of 2 X 4 sq.mm (56 / 0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade in 25 mm dia GI pipe ( Class ' B ' ) suitably bent at both ends with necessary angle iron upright and end supports for mains. SD 70

Supply and Fixing of 9W LED bulb including cost and conveyance of all materials and labour charges etc complete. SD 79

Supply and fixing of TNEB meter Board suitable for 32A Single phase service connection with 32A fuse unit(500V) 32A neutral link and earth link (1"x1/8" Copper flat) on TW plank of size 375mmx300mmx19mm with supporting TW reepers of 1" thick an either side with painting with suitable bolt and nuts for fixing the TW plank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit - SD No: 125

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Lower End - SD 506

Supply and fixing for Arial Fuse Unit SD 128

Provision for Earthing

Supplying and fixing of 110mm dia PVC pipe in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Provision for Leach pit arrangements

Manufacturing, supplying of 900mm dia Precast Reinforced Cement Concrete ring of 20-30mm thickness with 300mm hieght in RCC 1:1.5:3, using 10-12mm HBGS jelly including cost of reinforcement steel in position and cost of moulding charges, casting of ring, finishing, curing etc., complete complying with standard specification and as directed by the departmental officers

Manufacturing, supplying of 1000mm dia Precast Reinforced Cement Concrete slab of 40-50mm thickness in RCC 1:1.5:3, using 10-12mm HBGS jelly including cost of reinforcement steel in position and cost of moulding charges, casting of ring, finishing, curing etc., complete complying with standard specification and as directed by the departmental officers

Construction of Inspection Chamber 0.45 X 0.45 x 0.60 m with brick work and inner, outer plastering and covered with RCC Coverslab including all labour charges etc.,complete

110mm dia PVC pipe 4kg/sqm

110mm dia PVC elbow 4kg/sqm

110mm dia PVC Tee

Provision for Name Board with work details including cost and conveyance and all labour charges etc.,complete

GST Amount for providing Service to Government Contract Works for the above Construction Works. { GST Amount is the Total GST Amount for total overall quoted amount above this row in column "BB" for all works in this package}

YES PEE ASSOCIATES (BID ID -1379349)