CERTAIN REPAIRS TO FLOOR, ROOF, JOINERY, PLASTERING, PLUMBING AND SANITARY FITTING WORKS IN

Amount

Demolition of cement concrete in any position and removing the rubbish outside MOD land complete all as specified and directed.

Dismantling of Stone slabs in roofs including demolition of PCC over stone slab, suspended floors, chajjas, landings, etc., any thickness, jointed in any mortar complete all as specified and directed.

Dismantling timber scantlings 40 sqcm and over in section, in any position complete all as specified and directed.

Dismantling timber scantlings Framed work in fillets, rails, posts, rafters, purlins, etc. under 40 sqcm in section complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding ( but not backing) and disposal of rubbish outside MOD land complete all as specified and directed.

Demolition of brick or stone masonry built in cement mortar incl all quoins, arches, pillar etc. complete all as specified and directed.

Supply and fixing MS plain plates, square cut, with riveted, bolted or welded attachment FE-410-W (Gde-E-250) quality A as specified.

Material and Labour for MS work in Roof trusses (framed), trussed, purlins, crane gantries, rails, posts and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. including special shaped washer etc. complete and including all necessary drilling or cutting holes in brick/ concrete surfaces and making good, welding work, bolting or riveting etc and similar work conforming to Fe-290 Gde E-165 complete and all as specified.

Supply and fixing mild steel screw bolts 5cm to 10 cm length with hexagonal or square heads at one end and screwed at other fitted with washers complete all as specified and directed.

Supply and fixing for Pre-painted galvalume aluminum zinc coating GI based corrugated or semi corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

Supply and fixing for Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

Material and labour brick work with sub class ‘B’ bricks of class designation 7.5 all as per IS-1077-1992 (minimum compressive strength of brick 75 kg / Sqcm) old size bricks, straight or curved on plan exc 6 metre mean radius built in cement mortar 1:6 complete all as specified & directed.

All as per description of serial item No. 13.00 here in before but as in half brick thick walls built in cement mortar 1:4 complete all as specified and directed.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc.laid bedded and pointed in any mortar complete all as specified and directed.

Material and Labour Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete incl 15mm thick bedding layer CM 1:6 incl rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed.

Material and Labour 20mm thick Granite (of any type) tiles machine cut, in skirting/ dado laid over cement screed and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing incl 10mm thick cement plaster in CM 1:4 incl rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete complete all as specified and directed.

Material and Labour Green Marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade, including grinding and polishing Providing edge moulding to 18-20mm thick stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc.complete all as specified and directed.

Material and Labour for vitrified double charged light shade ceramic tiles 9 mm thick polished, area of each tile not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

Ditto all as per description of above ser item No.19 here in before but as in skirting and over 10mm cement backing in CM 1:4 complete all as specified and directed.

Material and Labour for coloured glazed tiles of size 300x450x7mm thick fixed with neat cement slurry in vertical surface to wall pointing in white/coloured cement to match over and including 10mm thick backing coat in CM 1:4, complete all as specified and directed.

Material and labour non-skid, ceramic coloured tiles 7 to 8mm thick (Square/rectangular ) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors, set and jointed in cement slurry and pointed in white or coloured cement to match with the shade of tiles laid over and including 15mm thick screed bed or bedding layer in cm 1:6 complete all as specified and directed.

Material and Labour for 25mm thick PCC (1:2:4) type B0 using 12.5mm graded aggregate as in sub floor, sub base; concrete surface finished even & rough to receive topping floor/tiles finish/layer complete all as specified.

Material and Labour 75mm thick PCC 1:3:6 type C-2 (using 20mm graded aggregate) as in plinth protection laid in alternet bays, surfaces finished even & smooth whtiout using extra cement including making joints complete all as specified and directed.

Material and labour 75mm thick PCC 1:4:8 type D-2 ( using 40mm graded aggregate) as in sub base of floor surface finished even & rough to receive floor topping complete all as specified and directed.

Material and Labour Non skid ceramic outdoor floor tiles 10 mm thick (square) area of each tile exc 0.06 sqm but n exc 0.11 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, over 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

Material and Labour PCC 1:2:4 type B-1 (using 20mm graded aggregate ) in roof kerbs or mud stops, rounded or chamfered on edges and the like finished fair and even including necessary form work complete all as specified and directed.

Dismantling boarding, any description, fixed in any position with fixed with screws complete all as specified and as directed.

Material and Labour Providing, making and fixing Gypsum Board False Ceiling straight or curve any profile of reputed make which includes G.I. Perimeter Channels of size 0.55mm thick (having One Flange of 20mm and another flange of 30mm and a web of 27mm) along with perimeter of ceiling, screw fixed to brick wall / partition with the help of Nylon sleeves and screws at 610mm centres. Then suspending G.I. intermediate channels of size 45mm (0.9mm thick with two flanges of 15mm each) from the soffit at 900mm centres with ceiling angle of width 25mm X 10mm X 0.55mm thick fixed to soffit with G.I. cleat and steel expansion fasteners. Ceiling section of 0.55mm thick having knurled web of 51.5mm and two flanges of 26mm each with lips of 10.5mm are then fixed to the intermediate channel with the help of connecting clips and in direction perpendicular to the intermediate channel at 457 mm centres 12.5mm tapered edge Gypboard (conforming to IS 2095-1982) is then screw fixed to ceiling section with 25mm dry wall screws at 230mm centres. Screw fixing is done mechanically with drilling machine with suitable attachment. Finally tapered edges of the Gypsum boards are to be jointed and finished so as to have a flush look which includes filling and finishing with jointing compound, joint paper/fibre tape and two coats of dry wall top coat suitable for Gypsum board etc. complete as per the recommended practices / specifications of the manufacturer. Including two coats of primer suitable for gypsum board two or more coats of plastic emulsion paint of approved shade and also including making necessary openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitable fixed all complete as per drawing and specification and direction. Rate to be inclusive of shadow profile at the junction of wall & ceiling, in between of ceiling, etc. complete. including all fittings approved by GE complete all as specified and directed. Note:-(a) The design of ceiling will be done in multy layers as per the direction of Eng-in-Charge and overlapping area will be measured & paid accordingly.

Supply and fixing Stainless Steel Corner glass shelf (Set of 3) with CP brackets 300mm x 300mm size fixed in repair as per sample approved by GE complete all as specifed and directed.

Supply and fixing Glass Shelf 600mm long with CP brackets as per sample approved by GE complete all as specifed and directed fixed in repair.

Supply and fixing CP Towel Ring 150mm Square/round incl fixing complete all as specified fixed in repair.

Supply and fixing towel rack 600mm long with lower hangers, incl 3 hooks Stainless Steel fixed in repairs complete all as specified directed.

Supply and fixing in repair HD perimeter circle lighted mirror of size 1016x1016x43mm including fixing complete all as specified and directed.

Supply and fixing in repair square/Ovel shape wall mounted full pedestal wash basin size 545mm x 489mm complete all as specified and directed.

Supply and fixing in repair Brass Chromium plated Central Hole Basin Mixer with Popup Waste System with 450mm Long Braided Hoses Hot and cold mixer fixed to wash hand basin incl all fixing accesaries complete all as specified and directed.

Supply and fixing in repair Toilet Roll Holder size 150mm with Stainless Steel Flap fixed to walls with chromium plated (CP) brass screws complete all as specified and directed.

Supply and fixing in repair Soap dish holder stainless steel chromium plated fixed with brass screws and rawl plug complete all as specified.

Supply and fixing in repair Soap Dispenser with Metallic Bottle fixed with brass screws and rawl plug complete all as specified.

Supply and fixing in repair Tumbler Holder stainless steel chromium plated fixed with brass screws complete all as specified.

Supply and fixing in repair brass chromium plated angular stop cock with wall flange15mm complete all as specifed and directed.

Supply and fixing in repair 15mm long body bib taps long shank chromium plated cast copper alloy with crutch or butterfly hadle secrwed for iron pipe or for brass ferrule complete all as specified and directed.

Supply and fixing Rimless Single Piece-WC with soft close slim seat cover, Hinges, Fixing Accessories, Accessories Set and Cistern fittings, Size: 360x730x740 mm, fixed in repairs complete all as specified directed.

Supply and fixing in repairs brass chromium plated Hand Shower (Health Faucet) with 8mm Dia, 1.2 Meter Long Flexible Tube & Wall Hook with N.R.V (Back Flow Preventer) complete all as specified directed.

Supply and fixing in repairs Overhead Shower 200X200mm Square Shape Single Flow (ABS Body Chrome Plated with Gray Face Plate) with Rubit Cleaning System complete all as specified directed.

Supply and fixing in repairs Hand Shower 140mm Round Shape Multi Flow with Air Effect (ABS Body & Face Plate Chrome Plated) with Rubit Cleaning System fixing to steel pipe or union complete all as specified directed.

Supply and fixing in repairs central hole Sink Mixer long body swang nech for mixing Hot & Cold water, cast copper alloy, chromium plated, screwed for iron pipe or for union, suitable for 15mm bore pipe, complete all as specified and directed.

Supply and fixing in repairs sink with drainage board made of stainless steel 1mm thick for kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 1143mm x 510mm bowl size 510mm x 406 mm x 203 mm complete all as specified and directed.

Supply and fixing in repairs brass chromium plated Wall Mixer 3-in-1 System with Provision for both Hand Shower and Overhead Shower Complete with 115mm Long Bend Pipe, Connecting Legs & Wall Flange (without Hand & Overhead Shower) complete all as specified and directed.

Taking down and refixing only GI pipe medium grade 15 mm dia with all fitting laid in floor or fixed in walls complete all as specified and directed.

Taking down and refixing only GI pipe medium grade 20 mm dia with all fitting laid in floor or fixed in walls complete all as specified and directed.

Supply and fixing GI pipe medium grade 15 mm dia with all fitting laid in floor or fixed in walls including taking down old GI tubes complete all as specified and directed..

Supply and fixing GI pipe medium grade 20 mm dia with all fitting laid in floor or fixed in walls including taking down old GI tubes complete all as specified and directed..

Material and Labour for 75 mm dia PVC (SWR) floor trap with CP grating, plain including jointing with solvent cement as in repairs complete all as specified and directed. Note : Cost of grating are included in this item.

Material and Labour for 100 mm dia PVC (SWR) floor trap with CP grating, plain including jointing with solvent cement as in repairs complete all as specified and directed. Note : Cost of grating are included in this item.

Demolition and breaking up drain pipes 110/75 mm bore (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as specified and directed.

Supply and fixing 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall & laid in trenches or in floors, including clamps as required, complete all as specified and directed.

Supply and fixing 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall & laid in trenches or in floors, including clamps as required, complete all as specified and directed.

Supply and fixing PVC(SWR) bends 110 mm dia complete all as specified.

Supply and fixing PVC(SWR) bends 75 mm dia with access door complete all as specified.

Supply and fixing PVC(SWR) bends 75 mm dia complete all as specified.

Supply and fixing PVC (SWR) vent cowl of 110 mm bore complete all as specified

Supply and fixing PVC (SWR) vent cowl of 75 mm bore complete all as specified

Taking down chowkats or frame not exc. 1.5 sqm each with shutters (without taking off shutters from the fames) complete all as specified.

Taking down chowkats or frame exc. 1.5 sqm but n.exc 4 sqm each with shutters (without taking off shutters from the fames) complete all as specified.

Taking down door shutter of any description exc 1.00 sqm but n. exc. 2.00 sqm each complete all as specified and directed.

Supply and fixing pressed steel frames 125x60mm for door with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete all as specified.

Supply and fixing pressed steel frames of size 105x60mm for doors with one or more rebates including necessary fixing, lungs, hinges, lock strike plate, etc complete all as specified.

Supply and fixing 35 mm thick 2nd class hard wood plain framed, panelled shutter (any number of panels) with panel of timber flat on both sides (feather edged) or of vaneered particle board medium density, wood particle board with commercial face veneers, supplied and fitted complete all as specified and directed.

Supply and fixing 30mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both side face is covered with approved laminated with lipping/frame to match complete all as specified and directed.

Material and Labour 35mm thick 2nd class hard wood glazed & gauged skeleton shutters open rebated and prepared to received glass/gauge etc. ( without sash bars) edges of framing plains chamfered or rounded fitted with cut and mitered bead for securing glass etc. complete all as specified. Note : - Wire mesh and glazing shall be measured and paid separatly in respected items .

Supply and fixing PVC solid door frame of size 50mm x 47mm made out of 5 mm wood grain printed PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with printed sheet, reinforced with MS square tube, as per specification and drawing in SSR Part-II complete all as specified and directed.

Supply and fixing Factory made solid PVC moulded door shutter with particle board core 30mm thick (style) consisiting of frame made out of M.S. Tubes for top & bottom rails M.S. frame shall be covered with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face strip of 20mm width struck inside with solvent cement for stiles and Prelam colour 10mm thick PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of Prelam colour 10 mm thick PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, fixing in the frame at the site as per specification & drawing.

Supply and fixing 100 mm long aluminium alloy anodised butt hinges and fixed fixed with stainless steel screws complete all as specified and directed.

Supply and fixing 150 mm long aluminium alloy anodised handles, fabricated type polished fixed with stainless steel screws complete all as specified and directed.

Supply and fixing 200 mm long aluminium anodized barrel tower bolt of extruded section fixed with stainless steel screws complete all as specified and directed.

Supply and fixing 300 mm long aluminium anodised sliding door bolt with hasp and staple(bolt type) and fixing clips of sheets cast of excruded section and fixing bolt and sliding bolts of extruded sections or cast-aluminium alloy and fixed.

Supply and fixing mild steel 300mm, ordinary rat tail rod pattern springs, including roller and roller plate including welding or screwing to MS frame complete all as specified and directed.

Supply and fixing 150 mm floor door stopper hanging type, consisting two leg aluminium anodised natural shade matt finish aluminium rod with rubber shoe complete all as specified and directed.

Supply and fixing Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified.

Supply and fixing in repairs Stainless steel (SS 202 grade) Curtain rod 25 mm dia 0.80 mm wall thickness, mild steel, chromium plated including supporitng brackets as per sample complete all specified and directed.

Supply and fixing in repairs Stainless steel (Grade 305) ornmental type brackets (Open ends) suitable for curtain rods of 25mm dia complete all specified and directed.

Supply and fixing in repairs Stainless steel (Grade 305) brackets (Dead ends) suitable for curtain rods of 25mm dia complete all specified and directed.

Taking down cement plaster on brick or stone surfaces including raking out joints hacking for key scrubbing down with water etc.complete all as specified.

Material and Labour for rendering 15mm thick plaster on fair faces of brick or concrete surfaces in CM 1:6 finished even and smooth without using extra cement complete all as specified.

Material and Labour for rendering 15 mm thick plaster on fair faces of brick work or concrete surfaces in CM 1:4 finished even and smoth without using extra cement complete all as specified.

Material and Labour rendering 10 mm thick plaster on ceiling (brick or concrete surfaces) in cement mortar 1:4 and surface finished even and smooth without using extra cement complete all as specified and directed.

Preparing new surfaces plastered or unplastered surfaces of walls by applying two coats of Plastic emulsion over a coat of primer, over a two coat of birla white putty complete all as specified and directed.

Preparation of newly plastered or unplastered surfaces of walls and applying two coats of exterior acrylic emulsion over a coat of primer, in camouflaging pattern approved by GE, complete all as specified and directed.

Preparation of new plastered surfaces of ceiling and applying Three coats of white wash complete all as specifed and directed.

Complete removal of existing treatment from old plastered surfaces of walls including brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss, efflorescence salts, trading oil, grease spot, washing etc. and applying Two coats of Plastic emulsion paint over a coat of primer, over and including two coats of birla white putty complete all as specified & directed.

Complete removal of existing treatment of wall including washing rubbing down and stopping of distempered or painted surfaces including all cornices, pilasters etc( plastered or unplastered) etc. and applying two coats of acrylic exterior emulsion paint over a coat of primer, of approved colour/shade as in camouflaging pattern approved by GE complete all as specified and directed.

Preparation of plastered or unplastered old decorated surfaces of ceiling etc. including pillasters and cornices etc. incl brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss, efflorescence salts, trading oil, grease spot, washing etc. and applying one coat of white lime wash complete all as specified.

Preparation of new wood or wood based surfaces of any description, not otherwise described over 10cm width or girth and applied two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

Preparation of old painted surfaces of wood based surfaces of any description exc 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified & directed.

Prepapration of new or previously untreated steel or iron surfaces of any description not otherwise described over 10cm width or girth & applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Preparation of old painted surfaces of Steel and Iron work of any description exc 10 cm width or girth and applying one coat of synthetic enamel paint on steel surface complete all as specified & directed.

Supply and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for frames of doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, complete all as per architectural drawings and the directions of Engineer-in-Chief

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws,rollers & dust proof brush for sliding door / window complete all as per architectural drawings and the directions of Engineer-in-Chief.

Supply and fixing 4.80 mm thick sheet glass of ordinary quality plain/tinted and including glazing with suitable rubber beads etc. complete all as specified.

Supply and fixing Anodised aluminum grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anode coating of grade AC15) of approved design/ pattern, with approved standard section and fixed to the existing window frame with CP. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminum standard section around the opening, all complete as per requirement and direction of Engineer in-charge.

Supply and fixing conceled lock (push to unlock) for sliding window made with zinc body, aluminium hook and anti rust material with powder coated metallic finish of approved colour having size 100mm x 24 mm incl necessary cutting for fixing all as specified and directed.

Taking down unserviceable existing sub main wiring copper/ aluminium conductor including conduit/ casing and capping etc. complete all as specified and directed.

Taking down unserviceable main switches, DBs / changeover switch alongwith Teak wood boards etc and making good the disturbed surfaces of wall / floors to match the existing surface complete all as specified and directed.

Taking down carefully old MCBs/Isolators any type by unscrewing from board complete all as specified and directed.

Material and Labour for point wiring using 1.1 KV grade single core FR-LSH flexible cable, conforming to IS 694: 2010, having multi-drawn thin strands of electrolytic copper conductors and insulation for phase, neutral, and earth continuity conductor connecting to earth dolly, colour-coded as per IS 11353: 1985, drawn in medium grade UPVC surface / recessed conduits, conforming to IS 9537 (Part- 3): 1983, of size not less than 20 mm NB, including cutting chases, factory made not less than 1.2 mm thick sunken, modular flush sheet galvanized metal enclosure haing zinc coating not less than 120 GSM, conforming to IS 14772: 2000, having top, bottom, side and back-wall knockouts for conduit entry from any direction, suitable modular cover-plates and making good of disturbed surfaces of wall / ceiling / floor, etc. complete all as specified in IS 732: 2019 and directed by the engineer-in-charge.

One fan point / Light Point controlled by one switch, with cables 1.5 sqmm size

One 6 A socket outlet on same Board, with cables 1.5 sqmm size

One 6 A socket outlet on ind Board, with cables 1.5 sqmm size

One 16 A socket outlet, independent, with cables 2.5 sqmm size

Supply and fixing modular type 2/3 pin combined shuttered type 16 A socket, conforming to IS 1293: 2005 complete all as specified in IS 732: 2019 and directed by the engineer-in-charge.

Supply and fixing modular type 2/3 pin combined shuttered type 6 A socket, conforming to IS 1293: 2005 complete all as specified in IS 732: 2019 and directed by the engineer-in-charge.

Supply and fixing modular type 6 A 1-way SP switch conforming to IS 3854: 2012 with finger-proof terminal complete all as specified in IS 732: 2019 and directed by the engineer-in-charge.

Supply and fixing modular type 16 A 1-way SP switch conforming to IS 3854: 2012 with finger-proof terminal complete all as specified in IS 732: 2019 and directed by the engineer-in-charge

Material and Labour for ceiling rose, surface bakelite, 65 x 50 mm, three terminals complete all as specified and as directed.

Supply and fixing sheet metal enclosure 20 Amps single pole and natural with a two pin and earth plug and socket complete in metal clad board (Industrial type) with one single pole MCB 20 Amp fixed properly in concealed position including making good disturbed surface all as directed.

Material and labour for Cutting, Opening through existing brick walls of 300 mm dia to be for exhaust fan/ventilating fan and finished with the disturbed wall by cement plastering and cement mortar 1:4 and match with the existing surface.

Supply and fixing Exhaust fan 300 mm dia including louvers AC single phase 240 volts of size 300 mm sweep(metal body) and not less than 900 RPM including flexible wire 3 core 1.5 Sqmm from ventilator fan to ceiling rose all as specified and as directed.

Supply and fixing sheet metal enclosures MCB TPN DB double door 4 WAY with 200 amps rated busbar, 415 volts, as per IS-8623 with double glazed door for incorporating MCBs, IP-43 including taking down old unserviceable single phase DBs, complete all as specified and as directed.

Supply and fixing MCB TPN 63 amps 'B' series breaking capacity 10 KA, 'B, curve, 415 V 50 Hz including necessary incoming and outgoing electric connection with suitable size of copper lugs etc.

Supply and fixing MCB SP, 6 to 40 Amps, 'C' series breaking capacity 10 KA, 'C' curve 240 volts, 50 Hz including necessary incoming and out going electric connection with suitable size of copper lugs etc.

Material and Labour for sub-main wiring with two single core 4 sqmm FRLS PVC insulated unsheathed stranded copper conductor cable drawn through including chasing cutting in any type of masonary including 20 mm dia non-metallic PVC conduit fixed in wall including 4 sqmm copper earth continuity wire, accessories and connecting to earth dolly complete, (for AC points). Note : 2 Run of 4 Sqmm, 1 Run of PVC conduit & 1 Run of 4 Sqmm earth cable shall be measured as single unit length.

Supply and fixing LED light fitting 1X10W bulk head luminaires with initial flux 1100 lumen, color temp 6500 K, color rendering index more than 80, including LED light incluiding driver and wall mounting holder connecting up with three core flexible copper conductor cable of suitable size.

Supply and fixing modular cover plate with frame, of following modules complete all as specified and directed. Note- Modular switches, sockets & Cover plates with frame shall be of same make & model.

8 Module

6 Module

3 Module

2 Module

Supply and fixing rectangular modular flush mounted Sunken block of following modules suitable for mounting, Modular switches & sockets, complete all as specified and directed.

8 Module

6 Module

3 Module

2 Module

Supply and fixing in repairs stepped type electronic fan regulator, 2 Module white polycarbonate body, flush type, 230 V, including connecting complete all as specified and directed.

Supply and fixing in replacement of energy efficient Surface/Wall Mounted 20W integrated LED batten 4 feet Fitting with polycarbonate housing. Total system Lumen of 20W to 22W LED should be 2200 or above in Cool day Light(5700K to 6500K), Power factor>0.95, CRI (Ra) >80, System Lumen Efficacy>110 Lm/w, THD(%) < 20, LED Lamp LED Lamp Efficacy>130 Lm/W with Average life of 50000 Burning hours complete with all accessories as required with connections complete all as specified and directed.

Supply and fixing ceiling fan complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated. Note: Old ceiling fans to be dismantled carefully and to be deposited in to MES Store.

Supply and fixing energy saving decorating box type batten light fitting 230 volts surface mounted complete with high effeciency glare free light LED lamp 10 watt blue coloured end caps with all accessories, pre- wired,CRCA housing integrated heavy duty electronic driver havinng THD < 10% including providing flexible copper wire twin core cable complete all as specified and directed.

Supply and fixing in repair Bell ding dong AC 230 Volts, including connecting complete all as specified and directed.

SHREE JASWANT CONSTRUCTION COMPANY (BID ID -3130243)

Beenu Co. Company (BID ID -3121940)

m/s gaurav enterprises (BID ID -3121832)