ADDN ALTN AND SPL REPAIRS TO BLDG NO. P 81, P 89, P 90 AND P 01 OR MD ACCN AT MEANEE LINES OF MEG CENTRE AND JCO S MD ACCN P 120, P 121 AT GNC LINE OF NO2 TRG CENTRE BANGALORE

Amount

Dismantling of single layer Mangalore pattern or similar tile in roofing all as specified and directed.

Dismantling of corrugated or semi corrugated Asbestos Cement sheets in roof coverings including ridges, valley gutters, etc. all as specified and as directed.

Dismantling wooden battens for tiles, shingles etc of any size including tilting fillets of spacing exc 15cm all as specified

Dismantling timber scantlings 40 sq.cm and over in section, in any position, in framed work all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for all as directed.

M&L for pre-painted galvalume coated high tensile corrugated/ trapezoidal profile steel sheets, AZ-70 coating mass, 550 Mpa yield strength, 0.50mm thick (TCT), as in roofing/ cladding to wall fixed with self drilling fasteners as per manufacturers instructions all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc.

M&L for pre-painted galvalume coated high tensile plain profile steel sheets, AZ-70 coating mass, 550 Mpa yield strength, 0.5mm thick (TCT), as in ridges, valleys, hips, claddings, etc. fixed with self drilling fasteners as per manufacturers instructions all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc.

S & F Rolled mild steel work as in (framed) purlins, rafter, roof trusses, rails and wind tie etc (Tee, Angle, channel or flat sections) incl distance pieces etc of Fe 410-W (grade E250) quality A all as directed.

S & F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 all as specified.

M&L plain cement concrete 1:3:6, type C1, using 20mm graded stone aggregate as in roof kerbs, mud stops, coving, etc. with rounded or chamfered edges all as specified and directed

Demolition of brick work masonry built in cement mortar pillars, etc. in any position below or above ground level all as specified and directed.

M & L for brick work with sub class B bricks straight or curved on plan to any radius in half brick wall built in CM 1:4 complete all as specified

M & L for brick work with sub class B bricks straight or curved on plan to any radius in brick wall built in CM 1:6 complete all as specified

Material and Labour for precast cement concrete block masonry with solid blocks exceeding 10cm in width, of grade C5 all as per IS 2185 - 1979, having minimum average compressive strength 5 N/sqmm at 28 days and density not less than 1800 kg/cum, set in CM 1:6 all as specified and directed.

M&L for plain cement concrete type D2 1:4:8 (using 40mm graded stone aggregate) as in foundation and mass concrete all as specified and directed.

Taking down cement plaster on brick or stone wall or ceiling concrete etc. including racking out joints hacking for key scrubbing down with water etc., complete removal of debris outside MD land all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15mm thick consisting of two coats (10mm thick in CM1:6 as in first coat and 5mm thick in CM1:4 as a second coat) on fair faces of brick work / block masonry or concrete surfaces mixed with WPC in 2nd coat finished fair and even without using extra cement complete all as directed. Note Supply only WPC shall be measured separately

M&L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper over a coat of alkali resistant primer all as specified and as directed.

M&L for preparation of new surfaces of wall and applying two coats of cement based paint all as specified and as directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings n. exc. 15cm thick, (below or above GL) as in plinth protection / Path/ hard standing / floor etc) complete removal of debris outside MD land all as specified and directed.

M&L for 75 mm thick PCC 1:4:8, type D2, (using 40mm graded stone aggregate) as in sub bases of floors complete all as specified and as directed.

M&L for 100 mm thick PCC 1:4:8, type D2, (using 40mm graded stone aggregate) as in sub bases of path complete, all as specified and as directed.

M&L for coloured non skid matt finished ceramic tiles, 7 to 8mm thick area of each tile exc 0.11 Sqm but not exc 0.18 Sqm, in floors, etc. set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigments to match the shade of the tile laid over and including 20mm thick screed bed in cement mortar 1:4 all as specified and directed.

M&L for coloured non skid matt finished ceramic tiles, 7 to 8mm thick area of each tile exc 0.06 Sqm but not exc 0.11 Sqm, in floors, etc. set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigments to match the shade of the tile laid over and including 15mm thick screed bed in cement mortar 1:6 all as specified and directed.

M&L for coloured glazed ceramic tiles 350x250x7mm / 450x350x7mm thick on vertical surfaces such as skirting, dados etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with surfaces with and including 10mm thick backing coat in CM 1:4 all as specified and directed.

Demolition of reinforced cement concrete in ground floors not exc 15cm thickness including cutting of reinforcement as required complete removal of debris outside MD land all as specified and directed.

Material and Labour reinforced cement concrete type M25 (design mix) using 20 mm graded stone aggregates as in beams, cantilevers, bressummers, lintel over 1.5m span, complete all as specified and as directed.

Excavating in trenches n exc 1.5m wide and n exc 1.5m depth and getting out in hard/ dense soil for foundation or shafts / man holes / sewage lines / pipes, cables etc, n exc 10 sq m on plan and n exc 1.5 m in depth all as specified and directed.

Returning, filling in with approved excavated soil including spreading levelling, watering and well ramming in layers n. exc. 25 cm thick all as specified and directed.

Material and Labour reinforced cement concrete type M25 (design mix) using 20mm graded stone aggregate as in foundation, footing, mass concrete etc., complete all as specified and as directed.

Material and Labour reinforced cement concrete type M25 (design mix) using 20mm graded stone aggregate as in columns complete all as specified and as directed.

Material and Labour reinforced cement concrete type M25 (design mix) using 20mm graded stone aggregate as in slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

M&L for steel form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter (Rough finished flat surfaces) complete all as specified and as directed.

M&L for steel form work to sides of pillars, struts, piers, columns and stanchions, square, rectangular or polygonal (Rough finished flat surfaces) complete all as specified and as directed.

Material and labour for steel form work to sides and bottom of beams (fair finished flat surfaces) complete all as specified and as directed.

Material and labour for steel formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed.

Material and labour for TMT bars 10mm dia and over, of grade Fe500D, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with MS wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified and as directed.

All as per sl. item No.38 here-in-before but 6 mm to 8 mm dia bars.

All as per sl. item No.38 here-in-before but 5 mm dia and over and upto 10 mm dia as in stirrups, spacers and binders

Taking down chowkhat with shutters (without taking off shutters from the frame) area not exc 1.5 Sqm each all as specified and directed.

Taking down chowkhat with shutters (without taking off shutters from the frame) area exc 1.5 Sqm and n exc 4 Sqm each all as specified and directed.

M & L for pressed steel frames of size 125 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc., including one shop coat of priming complete, size of frame made out of 1.25mm mild steel sheets with including Inside of frame filled with PCC 1:3:6 type C0 (using 12.5mm grades stone aggregate) complete as all as specified and as directed.

Supply & fix pressed steel frames fo size 105x60mm for doors with one or more rebates including necessary fitting lugs, hinges, lock strike plates etc including one shop coat of priming complete size of frame made out of 1.25mm mild steel sheets with including inside of frame filled with PCC 1:3:6 type C0 (using 12.5mm grades stone aggregate) complete all as specified & directed.

S & F factory made 2nd class hard wood 35mm thick panelled shutter (any number of panel) with panel of timber flat on both sides (feather edged) or of veneered particle board medium denisty with commercial face veneers with size of rails and stiles sizes of members of shutters as specified in SSR Part I, Section 8. Clause 8.24 (a) and fitted to chowkats all as specified and as directed.

M&L for factory made 30mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats all as specified and directed. Note: S&F GI wire cloth shall be measured and paid separately.

S&F factory made Box type Steel Windows/ventilators double side shutters (Windows side hung type) pressed steel frames made out CRCA Sheet of 80x60x1.25mm double rebated, Shutters box type made out of CRC Sheet of 40x20x1.0mm , windows & ventilator shutter fixed made of glass and gauge fixed with box type hinges, Aluminium die cast handles for glass shutters, Iron flat type handles for mesh shutters, telescopic stays, etc complete all as specified with and including 12mm square guard bars/grill welded with steel frame (100c/c horizontically) all as specified and directed by Engineer-in-Charge.

(i) The quote unit rate shall be of combined for steel frames, steel shutters and Guard bars / Grill and cost of beading, fittings such as handles, hinges,Telescopic stays, locking arrangements and fixing of glass and wiremesh etc.

(ii) Supply and fix 4 mm thick glass and GI / stainless steel wire mesh be measured and paid separately.

(iii) All Windows/Ventilator design shall as per CECZ TD drg No 539 Sheet 1/3 to 3/3

S&F Rolled mild steel Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming to Fe-410W Gde- E-250 Quality A all as specified and as directed.

S&F Expanded metal, cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members, weight per Sqm not exc 4 kg all as directed.

M & L for factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles) with 2,4 or 6 raised panel design with particle board core and 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face supplying and fixing in frame at site as per specification & drawing all as directed. Note: The quoted rate shall be inclusive of all builder's hardware as per manufacturer's instrucitons

M&L for solid PVC Door Frame of size 50mm x 47mm made out of 5mm prelaminated PVC sheet on both sides reinforced with M.S. Square tube, supplying and fixing in opening as per specification and drawing all as specified and as directed.

S & F Butt hinges extruded aluminium alloy with galvanised mild steel hinge pin anodised and fixed, of size 100 mm type C21 complete all as specified.

S&F aluminium handle, Cast type, anodised 150 mm long all as specified and directed.

S&F aluminium anodised barrel tower bolt of extruded section, 150mm long all as specified and directed.

S&F 200mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolts plate type with bright bolt not less than 12mm dia all as specified and directed.

S&F Steel ventilators with top hung shutter including hinges, steel peg stay complete all as specified and as directed

(i) The quote unit rate shall be of combined for steel frames, steel shutters and Guard bars / Grill and cost of beading, fittings such as handles, hinges, Telescopic stays, locking arrangements and fixing of glass and wiremesh etc.

(ii) Supply and fix 4 mm thick glass and GI / stainless steel wire mesh be measured and paid separately.

(iii) All Ventilator design shall as per CECZ TD drg No 539 Sheet 1/3 to 3/3

S & F galvanized mild steel wire cloth 0.56mm nominal dia and average width of aperture 1.18mm and fixed with tinned tack or galvanized wire staple all as directed fixed.

Supply & fix 4mm thick figured glass pin head type ordinary quality and glazing in square n. exc 0.5 sqm in each pane

S&F floor door stopper of aluminium alloy body and tongue,anodized with hard drawn steel spring fixed in floor, over all length of cover plate 140mm all as directed.

S&F Harrison rails of 20mm dia, anodised aluminium alloy with fixing brackets etc. all as directed.

S&F MS butt hinges 50mm in size, medium weight, cold rolled all as specified and directed.

Supply and fix ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed all as directed.

S & F vitreous china wash down water closet pan (Pedestal Pan) including fixing bolts, flush pipe anti syphonage pipe, etc complete of cera model cat pt no. 2008 including plastic EWC seat cover, coloured closed pattern with flat bottom and cover of cera model cat pt 2308 and mild steel chromium plated or aluminised hinging device with and including PVC valveless, syphonic action type flushing cistern, low level, white,with inlet, ball valve, float and handle 10 ltrs capacity including brackets and Stop valve fancy type cast copper alloy chromium plated screwed down, screwed for iron pipe or for brass ferrule and fixed 15mm dia, fixed as in repair, .complete all as directed. Make : Cera Cat No. S1050101 for EWC, B1520101 for seat cover, S1061106 & B1810110 for PVC flushing cistern and HTF 3001201 for CP stop cock or equivalent model in Prayag / Parryware / Jaquar

S & F vitreous china wash basin white flat back of size 550x400mm excluding chain and plug and porcelain stopper but incl CI bracket CP waste coupling 32mm with and including 32mm PVC waste pipe 75 cm long and 15mm dia PVC connection 600mm long, Pillar tap fancy type cast copper alloy, Stop valve fancy type chromium plated screwed down, screwed for iron pipe or for brass ferrule and fixed 15mm dia etc complete fixed in repair all as specified and directed. make : Cera cat No. S2040103 for WHB, HTF3001101 for pillar tap, F8050102 for waste coupling or equivalent models in parryware / jaguar / Johnson/ prayag

S&F "in repair" 1mm thick stainless steel sink, overall size 915x460mm, bowl size 410x330x160mm, with plug, washers & wastes incl bedding in cement mortar, fixing cantilever brackets & connecting union to pipe including waste pipe 75cm long, waste fittings, brass, chromium plated 40mm fixed on brick / PCC block walling complete all as specified and as directed. Make : Cera Cat No. B4512201 (gloss finish) or equivalent models in Johnson / Bluestar / Prayag

Supply and fix Bib tap cast copper alloy fancy type chromium plated screwed down, screwed for iron pipe or for brass ferrule and fixed 15mm dia, fixed as in repairs, all as specified.Make : Cera Cat No. F3001152 or equivalent models in Johnson / Bluestar / Prayag

S & F Health faucet (ABS body) with 1.2 mtr long PVC tube and wall Hook complete all as specified and as directed Make: Cera F8030103 or equivalent models in Parryware / Johnson / Jaquar

S& F Concealed Stop valve 15mm fancy type cast copper alloy chromium plated screwed down, screwed for iron pipe or for brass ferrule and fixed 15mm dia, fixed as in repairs all as specified. Make : Cera Cat No. HT F3001351 & HT 4050102 or equivalent models in Johnson / Bluestar / Prayag

S & F soap dish fancy type of brass CP complete all as specified. Make: Make : Cera Cat No. F5007106 or equivalent models in Johnson / Bluestar / Prayag

S & F Swivel shower rose of CP 15mm suitable for fixing with 15mm dia pipe all as specified. Make: Make : Cera Cat No. F7010213AB or equivalent models in Johnson / Bluestar / Prayag

S & F 20mm stop cock cast copper alloy screwed down high pressure with crutch or butter fly handle screwed both ends or for unions etc, fixed in repair all as specified.

S&F PVC Mirror cabinet of size 350 x 450 mm complete all as specified and as directed. Make: Prayag, Cat no:551 or equivalent models in parryware as approved by GE.

Taking up or down existing unserviceable 15mm bore GI tubes of any grade all as specified and directed.

Taking up or down existing unserviceable 20mm bore GI tubes of any grade all as specified and directed.

S&F 16mm (outer dia) CPVC pipes (ISI Marked) SDR 11 & CPVC SDR 11 fittings, fixed complete to walls, ceilings or laid in floors all as specified and directed.

S&F 20mm (outer dia) CPVC pipes (ISI Marked) SDR 11 & CPVC SDR 11 fittings, fixed complete to walls, ceilings or laid in floors all as specified and directed.

S&F "in repairs" 110mm bore, type B, UPVC (SWR) pipes, single socketed, in any length with rubber ring joints fixed to walls, all as specified and directed

S&F "in repairs " 75mm bore, type B, UPVC (SWR) pipes, single socketed, in any length with rubber ring joints fixed to walls all as specified and directed

S&F 75mm bore, type B , UPVC (SWR) bends any radius with access door all as specified and directed.

S & F 110mm bore, type B, UPVC (SWR) reducer all as specified.

S & F 110 mm bore, type B, UPVC (SWR) junction single (single T) equal or unequal with access door all as directed.

M & L for UPVC (SWR) floor trap with grating including jointing to waste pipe fixed in cement concrete type B1(1:2:4), for diameter of outlet 75mm, all as specified.

M&L for UPVC (SWR) gully trap 125/110mm setting and jointing with solvent cement all as directed.

S & F "in repairs" 1 mm thick stainless steel plate rack of size 790x910x250mm including fixing with rawl plug and screws on walls all as specified and as directed. Make Cat part No P 348 of Prayag or equivalent models in Bluestar/ diamond / Prince

Removing excavated soil n.exc 50 m and depositing where directed at a level n. exc. 1.5 m above the starting point in soil all as specified and directed.

M&L for mild steel small articles like bands, straps, including bolts, if required; hooks (stay), hook and pintle hinges; large hasps and staples; hand made sliding bolts; clamps; hold fasts; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar articles conforming to Fe-290 Gde-E-165, all as specified and as directed.

M&L for machine cut Cudappah stone slab, 20-25mm thick, as in shelves, stone slab edge rounded one side including rubbing and polishing complete all as specified and directed.

S&F 18/19 mm thick particle board, medium density, flat pressed single layer type BWR grade all as specified.

M&L for 2nd class hard wood chowkhat or frames, plain, solid, wrought, framed and rebated on the solid rounded or chamfered, put together with glue pinned at joints, fixed in position all as specified and directed.

Supply and fix "E" grid suspended false ceing grid system of size 600x600mm with main runner 29x24.7x0.8mm, cross tee 29x24.7x0.8mm and wall angle 22.2x22.2x0.65mm, ceiling suspended with 3mm dia GI wire hanger fixed with steel dash fastner, butter fly clips, hold down clips etc (Main runner, cross tee & wall angle of MS galvanised with PPPCGS) with and including 4mm thick HPSC (High Pressure Steam Cured) self textured design pre primered non asbestos fibre cement building board fixed to false ceiling including one coat of distemper on soffit of board complete all as per manufacturers instructions and as directed.

Supply and fix Brass chromium plated Tubular towel rail 20mm dia of 600mm long between flanges fixed in repairs all as specified. Make Cera Cat No. F5006103 or equivalent models in prayag / Jaquar

M & L for Brickwork with sewer bricks straight or curved on plan exc 6 m mean radius built in CM 1:4 for man-holes/ septic tank/ soakwell etc. in sewer works complete all as specified and as directed.

M&L for preparation of new wooden surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified and directed.

M&L for plain cement concrete 1:3:6, type C1, using 20 mm graded stone aggregate, 75mm thick as in plinth protection, finishing the surface fair and even, in panels & filling joints with mastic filling comprising 1 part of heated bitumen 85/25 grade and 3 parts of sand (all by weight), etc. including roughening surfaces of old concrete floor all as specified and directed

Dismantling water tanks (exc 250 and not exc 500 ltr) and taken in to sch of credit all as specified.

Disconnecting existing tanks (exc 250 and not exc 500 ltr) setting aside(or lowering if required) for repairs cleaning etc and hoisting if required connecting and refixing in position, cleaning, repairing etc cleaning and removing all scale and dirty etc from tanks and mouths of circulating pipes all as directed.

M&L for 500 litres capacity rotational moulded polyethylene (HDPE) water storage tanks, 'ISI' marked, cylindrical, vertical with closed top conforming to IS 12701-1989 having two layers wall construction with manhole lid and suitable locking arrangement including making holes for inlet, outlet and over flow pipes, hoisted and fixed in position including testing complete all as specified and directed.

Supply and fix 20mm bore dia ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe all as directed.

M&L for preparation of new steel surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

M&L for providing precast reinforced cement concrete 1:2:4, type B1, using 20 mm graded stone aggregate as in cover slabs (for manholes etc) chullah hoods, chajjas, water troughs, mangers, shelves and small articles with plain faces, etc. set in CM 1:6 all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished, and reforming benching as required for internal dia 100mm all as directed.

Complete removal of existing treatment on walls including brooming down or steel wire brushing, scraping down etc all as specified.

M&L for three coats of white wash on newly plastered ceiling including necessary preparation of surfaces all as specified and directed.

Demolition of reinforced cement concrete of any description and size and in any position including cutting of reinforcement as required complete removal of debris outside MD land all as specified and directed.

Demolition of stone slab of any description and any thickness in floors / walls laid, bedded and pointed in any mortar complete removal of debris outside MD land all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing, rubbish off the premises all as specified and directed.

Taking down shutters of any description area exc 1 sqm and n.exc 2 sqm each all as specified and directed.

Taking down shutters of any description area exc 1 sqm and n.exc 2 sqm each easing, adjusting and refixing in the same opening including existing builders hardwares all as specified and directed.

Dismantling boarding of any description fixed in any position with nails all as specified and directed.

Taking up or down existing 25mm bore GI tubes of any grade including cleaning and refixing all as specified and directed.

Raking out joints/ pointing to random rubble or polygonal rubble uncoursed or brought up to courses built in cement mortar complete all as specified and directed.

Material and labour for Keyed pointing in CM 1:4 to random or polygonal rubble, uncoursed or brought upto course complete all as specified and directed.

Cutting holes in brick walls of exc one but not exc two brick thick built in cement mortar complete all as specified and directed.

S&F 30mm thick flush shutters, solid core construction, with block board core and plywood face panels and commercial type on both sides with suitable teak wood lipping, fitted to chowkats all as specified and as directed.

M&L 25mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

All as per item No. 116 above but 18/19mm thick Prelaminated particle board

All as per item No. 116 above but 9mm thick Prelaminated particle board

M&L 18/19 mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete fixed in pelmet boxes or in narrow widths not exc 15cm each rebated or flat edged all as specified and directed.

S&F continuous (piano) hinges, mild steel, bright finish or electro galvanised with width of flaps when open 30mm all as specified and as directed.

S&F Brackets for brass chromium plated tubular towel rail 20mm dia all as directed.

S&F 4 mm thick sheet glass ordinary quality type n.exc. 0.5 sqm each pane complete all as specified and directed.

S & F "in repairs" Butt hinges,100 mm size medium weight, cold rolled mild steel complete all as specified and directed.

S&F aluminium anodised barrel tower bolt of extruded section, 200mm long all as specified and directed.

S&F "in repairs" anodised barrel tower bolt of extruded section, 200mm long all as specified and directed.

S&F extruded aluminium alloy handles, 100mm in size, fabricated type, anodised all as specified and directed.

S&F "in repair" extruded aluminium alloy handles, 150mm in size, fabricated type, anodised all as specified and directed.

S&F 300mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolts plate type with bright bolt not less than 12mm dia all as specified and directed.

S&F "in repairs" 300mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolts plate type with bright bolt not less than 12mm dia all as specified and directed.

S&F 100mm Hasp and staple, safety type, aluminium anodised with hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire & average width of aperture 1.40mm fixed with stainless steel wire staples all as specified and directed.

M&L for one coat of synthetic enamel paint on old painted wooden surfaces of any description over 10cm width or girth including necessary preparation of surfaces all as specified and as directed.

M&L for one coat of synthetic enamel paint on old painted steel surfaces of any description over 10cm width or girth including necessary preparation of surfaces all as specified and as directed.

Cleaning the roof surface by roughening, sweeping clean and washing down and applying cement slurry @ 3 kgs/sqm all as specified

M&L for rendering 15mm thick fair finishes of brick work / concrete surfaces of roof in CM (1:3) finished even and smooth without using extra cement mixed with integral water proofing compound all as specified. Note : Supply only water proofing compound will be measured separately

M &L for applying oil bound bitumen primer @ 0.20 kg/sqm and providing 3mm thick APP modified water proofing membrane weighing not less than 3.6 kg/sqm reinforced with non woven polyester matt weighing not less than 160 gm/sqm having softening point not less than 150mm centigrade, having tensile strength of 650 N/5cm and 350 N/5cm in longitudinal and transverse directions respectively of the reinforced tearing strength of 180N by torch application with minimum 10cm side overlapping and 15cm end lap, applying a coat of blown grade hot bitumen 90/15 over the membrane @ 1.2 kg/sqm top of membrane surface shall then be finished with solar reflective bituminous aluminium paint @ 0.10 kg/sqm complete all as per manufacturer instructions and as directed by Engineer-in-Charge.

NOTE: (i) APP modified water proofing membrane shall be of any one of the approved makes as specified here-in-after and shall conform to specifications given IS 16540-2017/ IS 16532-2017. (ii) Contractor shall produce necessary test certificate of the manufacturer to the Engineer-in-charge before incorporation in the work. (iii) Necessary independent tests shall also be carried out by the contractor without any extra cost to the Deptt as per relevant IS specifications and membranes with satisfactory test results shall only be incorporated in the work. (iv) The work shall be executed through authorised applicators of original manufacuturer only.

Material and labour for rendering 15mm thick on stone masonry surfaces or surface other than fair face of brickwork or on one side of lathing in CM 1:3 mixed with water proofing compound and finished even and smooth without using extra cement all as specified and as directed. Note: Supply only Water proofing compound measured seperately.

Supply only approved integral water proofing compound all as specified.

M&L Bitumen blown any grade, applied hot, two coats, to concrete surfaces at the rate of 1.5kg. per sq. m per coat for sunken floor treatment all as specified and directed.

Material and labour for APP based polymeric membrane weighing not less than 3.6kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) and on primed surface by forced application complete all as specified and directed. Note: The work shall be carried out by authorised applicators of manufacuters after written approval from GE.

M&L for plain cement concrete type E2 1:5:10 using 40mm graded stone aggregate as in foundation and mass concrete all as specified and directed.

S&F 40mm (outer dia) CPVC pipes (ISI Marked) SDR 11 & CPVC SDR 11 fittings, fixed complete to walls, ceilings or laid in floors all as specified and directed.

Material and labour for Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests including PVC SWR P trap connecting to flush pipe and to anti syphonage pipe, etc. complete including making good to floor., fixed in repairs complete all as specified and directed. Make Cera Cat No. S3010108 (Clovin) or equivalent model in parryware / prayag / jaquar

S&F syphonic action type low level PVC flushing cistern, 10 litres capacity, white, with inlet, ball valve, float, handle and flush pipe etc complete fixed in repair all as specified and directed. Make Cera Cat No. S1061106 & B1810110 or equivalent model in parryware / prayag / jaquar

S&F in repairs PVC Connection 15mm dia with PTMT nuts of length 450mm all as specified.

S&F in repairs 25mm bore gun metal gate valve heavy duty ISI marked with iron wheel head screwed both ends to iron pipes and fixed all as specified and as directed

S&F 25mm (outer dia) CPVC pipes (ISI Marked) SDR 11 & CPVC SDR 11 fittings, fixed complete to walls, ceilings or laid in floors all as specified and directed.

S & F "in repairs" UPVC (SWR) branch piece of 110mm bore, type B, single (single Y) equal or unequal complete all as specified and directed.

S & F "in repairs" UPVC (SWR) branch piece of 75mm bore, type B, single (single Y) equal or unequal complete all as specified and directed.

S&F Cast iron work grade FG 150 for articles n exc 5 kg each, unmachined, in brackets, gully traps, gratings, railing, frames, manhole covers, fire and soot doors, dampers, stop valve boxes, gate stops, parts of ranges, balusters and similar articles all as specified and as directed.

S&F Stainless steel wall hanger fixed to wall/doors with necessary nails/screws to hold in position complete all as specified and directed.

Cleaning and removing all scale and dirt, etc, from tanks of capacity exc. 250 and not exc 500 ltrs and dirts from mouths of circulating pipes, etc. all as directed.

M&L for 25mm thick plain cement concrete 1:2:4 type B0 (using 12.5mm graded stone aggregate) as in sub base for flooring finished even and fair all as specified and directed.

M&L 15mm thick screed bed or bedding layer of mortar in cm 1:6 for laying floor finishes complete all as specified and directed.

M&L 10mm thick backing on fair face of brick work or concrete surfaces in cement mortar 1:4 complete all as specified and directed.

M&L for non -skid coloured ceramic tiles, edge cut, 8 to 10mm thick area of each tile exc 0.18 Sqm but not exc 0.36 Sqm, in floors, etc. set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigments to match the shade of the tile all as specified and directed.

M&L for precast cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) solid building blocks or slabs 10cm thick (with plain or interlocking joints as directed) setting in cement mortar 1:6, complete in walls all as specified and directed.

Brushing neat cement slurry with 3.0kg of cement per sq. metre, including cleaning of rusted steel particles in reinforcement complete all as specified and directed.

M&L for GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding, joists, etc. in walls,ceilings,stanchions, beams, etc. including all laps, cutting and waste

M&L for rendering consisting of 20mm thick in two layers (10mm thick in CM1:6 as first coat and 10mm thick in CM1:4 with WPC as second coat) on "other" side of lathing surfaces finished even & smooth without using extra cement all as specified and as directed.

M&L for rendering consisting of 20mm thick in two layers (10mm thick in CM1:6 as first coat and 10mm thick in CM1:4 with WPC as second coat) on one side of lathing in CM 1:4, surfaces finished with even & smooth without using extra cement all as specified and as directed.

Material and labour for complete removal of existing treatment and applying two coat of oil bound distemper over a coat of chalk whitening primer including preparation of surfaces on wall surfaces all as specified and as directed.

M&L for complete removal of existing treatment and applying three coats of white wash including preparation of surfaces on wall surfaces complete all as specified and directed.

M&L for rendering 10mm thick on fair face of brick work or concrete surfaces of ceiling in CM (1:3) finished even & smooth without using extra cement all as specified and as directed.

M&L for two coat of cement based paint on old cement painted walls, pillasters, cornices, etc., including necessary preparation of surfaces all as specified and as directed.

M&L for complete removal of existing treatment and applying two coat of cement based paint on wall surfaces after preparing surface of wall including necessary chalk whiting priming complete all as directed

M&L for one coat of white wash on old decorated surfaces of ceilings including necessary preparation of surfaces all as specified and as directed.

M&L for machine cut Kota stone slab, 20-25mm thick, as in flooring, laid and jointed with neat slurry and pointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for machine cut Kota stone slab, 20-25mm thick, as in risers of steps, skirting, dado, cladding to pillars, etc., laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including 10mm thick backing coat in CM 1:4 all as specified and directed.

Rounding to edges of stone slabs of thickness 20-25mm, on one edge as in steps, cooking platform and other similar situations all as specified

M&L for chequered cement concrete tiles 30cm x 30cm x 25mm thick, industrial type coloured , set jointed and pointed in neat cement slurry, laid over and including 20mm thick screed bed in cement mortar 1:4 as complete all as specified and directed.

Complete removal of existing water proofing treatment of any type all as directed and disposed off outside MD premies all as specified and as directed.

M&L for machine cut Kota stone slab, 40-45mm thick, as in flooring, laid and jointed with neat slurry and pointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including 20mm thick screed bed in cement mortar 1:6 all as specified and directed.

M&L for cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregate) in cills, steps,coping,apexstones,bed plates and the like including necessary formwork as directed

S & F 110mm bore UPVC (SWR) bends all as specified.

S&F 75mm bore UPVC (SWR) pipes, single socketed, in any length with rubber ring joints fixed to walls all as specified and directed

Supply and fix factory made rubber moulded precast concrete interlocking paver block with glazed finish, any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade with using grey cement and no pigment over and including 50mm thick M sand cushioning spread, levelled uniformly and consolidated etc all as specified and directed.

Taking down old surface copper / aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc and for taking credit and making good distrubed surfaces of wall, floors, etc. all as directed.

M&L for Point wiring with PVC insulated and unsheathed FRLS cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts grade cable conforming to IS-694 1990 drawn in and including PVC rigid non metalic grey conduit, medium grade, on surface conforming to IS-9537 with all accessories including MS terminal boxes of 1.22mm thick fixed on wall with 3mm thick PVC laminated sheet top cover fixed with steel screws for mounting switches, sockets, regulator etc including 1.5 sqmm single core PVC insulated and unsheathed copper earth continuity conductor as earth and coneected to earth dolly for one light or fan point controlled by one 5 Amps switch one way complete all as specified and directed.

All as described in item No. 179 but for one 3 pin socket point 5 Amp on independent board

All as described in item No. 179 but for One 3 pin socket point 5 Amp on same board with other switches.

All as described in item No. 179 but for one bell/buzzer point controlled by one push button on the same board with other switches or indpendent place.

All as per item No. 179 here-in-before but with 2.5 sqmm size single core multistranded copper conductor cable for 6 pin 15 Amps switch socket combination outlet on independent board with 2.5 sqmm PVC insulated and unsheathed copper conductor as earth and connected to earth dolly.

M&L for Switch piano, flush button single pole, 5 Amps one way. all as specified and directed.

S&F Switch socket combination flush type 5 Amp 2 /3 pin all as specified and directed.

S&F Switch socket combination flush type 5/15 Amps 3/3 pin universal multipurpose all as specified and directed.

S&F Bell push, flush type, single pole one way, 5 Amps, 230 volts AC complete. all as specified and directed.

S&F Ceiling rose surface bakelite 65x50mm three terminals all as specified and directed.

S&F Door bell electronic, bul-bul music type, 230 volt AC all as specified and directed.

S&F fan regulator electronic, step type 230 volt, 50Hz suitable for 1200/1400mm sweep ceiling fan. all as specified directed.

Supply and fix LED batten luminaries surface mounted 4 feet system wattage of 20 Watts and not less than 2000lm with lifetime of 50000 burning hours with 70% of its initial lumen maintained. CRI>80, Power Factor > 0.95, THD< 10%, colour temperature≥5700K, surge protection3KV in CM, IP-20 protected, meets LED IS specifications, , Short circuit and over circuit protection, voltage range - 150 to 270 Volts AC, temperature range 0 to 50DegreeC, system efficacy at luminarie level ≥ 100 Lumens/watt and including connecting up with PVC sheathed 1.5 sq mm 3 core copper conductor flexible wire fixed complete all as specified and directed. (Make-Philips/ Wipro / Havells)

Supply and fix LED batten luminaire surface mounted 2 feet system wattage of 10 Watts and not less than 1000lm with lifetime of 50000 burning hours with 70% of its initial lumen maintained. CRI>80, Power Factor > 0.95, THD< 10%, colour temperature ≥ 5700K, surge protection 2KV in CM, IP-20 protected, meets LED IS specifications, Short circuit and over circuit protection, voltage range - 150 to 270 Volts AC, temperature range 0 to 50 DegreeC, system efficacy at luminarie level ≥100 Lumens/watt and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire to fitting fixed complete all as specified and directed. (Make-Philips/ Wipro/ Havells)

M&L for Sub main wiring surface type with 2 runs of 6.0 sqmm, single core, PVC insulated & unsheathed cable conforming to IS-694, FRLS, 1100 volts with copper conductor multi stranded drawn in existing non metallic PVC grey conduit with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 6.0 sqmm single core PVC insulated & unsheathed copper conductor FRLS Cable as continuos earth wire dolly and connecting to existing main switch board / distribution board of the building as ordered and testing on completion including taking down old submain wiring complete all as specified and directed. complete all as specified and directed. (Note: 3 runs of 6.0sqmm cable shall be measured as single run/unit)

M&L for Sub main wiring surface type with 2 runs of 4.0 sqmm, single core, PVC insulated & unsheathed cable conforming to IS-694, FRLS, 1100 volts with copper conductor multi stranded drawn through and including non metallic PVC grey conduit, medium grade with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 4.0 sqmm single core PVC insulated & unsheathed copper conductor FRLS Cable as continuos earth wire dolly and connecting to existing main switch board / distribution board of the building as ordered and testing on completion including taking down old submain wiring and type of conduit complete all as specified and directed. (Note: 3 runs of 4.0sqmm cables and one run of PVC conduit shall be measured as single unit)

S&F in replacement Sheet metal enclosure (ISI marked) distribution board TPN 4 way, suitable for MCB TPN as incomer, 415 V, having degree of protection as per IP 43-IK09 with 200 Amps rated copper bus bar with neutral link, horizontal type , double door, for housing MCB and fixed flush in wall surface, and tested on completion complete all as directed. Make :Legrand/Havells/Siemens

S&F in replacement Sheet metal enclosure (ISI marked) distribution board for 240 Volts, SPN 8 Way suitable for MCB SPN as incomer having degree of protection as per IP 43-IK09, horizontal type, double door, single pole and neutral with 200 Amps rated neutral copper bus bar for housing MCB and fixed flush in wall surface, and tested on completion complete all as directed. Make: Legrand/Havells/Siemens

S&F in replacement MCB single pole 6 to 32 Amps, "C" curve, 50 Hz, 240 volts, 10 kA rupturing capacity providing in DB complete all as specified. Make; Legrand/Havells/Siemens

S&F in replacement MCB single pole & neutral 32 to 63 Amps, "C" curve, 50Hz, 240 volts, 10 kA rupturing capacity providing in DB complete all as specified. Make; Legrand/Havells/Siemens

S&F in replacement MCB TPN 63 A, "C" curve, 50 Hz, 415volts 10 kA rupturing capacity providing in DB complete all as specified Make; Legrand/Havells/Siemens

Taking down ceiling fan from existing position and dismantling blades and removing fan and deposit to store complete all as directed.

M&L for hanging of ceiling fan after cleaning, greasing, servicing, painting with one coat white synthetic enamelled paint of approved colour by spray painting and writing MES number with black paint to a size of 25mm and replacement of required size copper conductor from ceiling rose to connector block of fan all as directed.

Supply and fix energy efficient ceiling fan, five star rating, white /Ivory 1200 mm sweep, 3 wings suitable for operation on AC 220/230 volts single phase, 50 hz supply with down rod of suitable length complete, including provision of hook for handing fan of suitable thickness and size fitted on existring tress with bolts, nuts etc including necessary PVC insulated flexible copper wire 23/0.0076 for connecting from ceiling rose to connector etc., complete all as specified and as directed Make: HAVELLS Model No. ES-50 5 STAR or equivalent model in makes CG/ ORIENT

S&F for exhaust fan, 300mm sweep, 230/240 Volts, 1400 RPM, heavy duty, single phase, metallic body with louvres and fixing arrangements with fixing bolts and provision of 3 core flexible copper conductor cable of size 1.5sqmm size from ceiling rose to connector of exhaust fan and testing with and including making circular hole of suitable in brick masonry / stone wall and making good disturbed surfaces to match with existing surfaces all as specified as directed. Make: Havells Turbo Force SP model or equivalent model in Almonard/ Crompton Greaves

S&F storage type water heater (Geyser), 25 litres capacity, 2 KW, BEE 5 Star rating, vertical type powder coated metalic body, including drilling holes into wall, provision of 02 Nos, 15mm dia heavy duty hot & cold steel wired braided connection including pressure release valve, safety valve etc & 4 Nos suitable size anchor bolts, nuts and washers, connecting up electrical & water supply lines, testing and making good disturbed surfaces complete all as specified and as directed. Make: MONZA EC Model of HAVELLS or equivalent model in RACOLD/ VENUS

S&F mild steel galvanized pipe light grade for protection & passing of LT cable fixed to poles/walls/laid under floor/roads complete including fittings/clamps as required at site all as specified for size of 40mm bore including taking dowm the old pipe all as directed.

M&L for earthing complete with galvanised steel earth plate electrode 60cm x 60cmx6.0 mm thick buried directly in ground (Earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below normal ground level connecting with steel GI earth wire 4mm dia by means of bolt nut check nuts and washers including PCC pit with 1:2:4 type B-1 using 20mm graded stone aggregate and frame cover of angle iron 25x25x6mm, MS sheet 3mm thick, and handle of 6mm dia MS bar made to shape, GI medium grade 20mm bore pipe for watering common salt chorcoal funnel wiremesh, earthwork in any type of soil returning filling in and removal of soft/loose soil to a distance n. exc 50 mtr including earth test point and making connections, testing on completion all as per electric plate No 3 of SSR Part-I and directed by engr-in-charge at site including taking down of old U/S eartning materials,Note :The unit rate quoted shall be inclusive of 7.5 mtr earth lead.

Supply and Fix 25W High efficient LED Security light fitting around the building, Aluminium pressure Die cast housing with pure polyester powder coated for long life, High purity lenses for superior performance, IP65/66 protection, Suitable for external pipe dia Up to 50 mm, with Luminiare efficacy>100lm/W, driver Voltage range 150-270V AC, temperature range- 0 to 50DegC, Driver efficiency > 85%, Power factor > 0.95, THD<10%, CRI >70, Colour Temperature≥ 5700K, with Luminiare efficacy≥100lm/W, Surge protection from overvoltage- 2.5KV in CM, Safety Extra Low Voltage Safe level as per IEC standard, 50000 burning hours as per L70 Criteria, including provision of 40mm dia GI light grade pipe1.5 mtr length bend to shape and necessary clamps etc for fixing the light fittings on wall fixed complete as specified and directed Make: Wipro/Philips/ Havells

S & F sheet metal enclosure single pole and neutral enclosure with two pin and earth plug and socket complete with one single pole MCB of 20 Amps all as directed. Make: Legrand / Havells / Siemens

Removing excavated surplus soil to a distane exc 250m and n.exc 500m and depositing where directed at a level n.exc 1.5m above the starting point in soil all as specified and directed.

Removing the existing enery meter by disconnecting all electrical connection and re fixing the energy meter - 1 No including provision of 5mm thick and suitable size of laminated sheet fixed on wall with 4 nos porcelain support having sufficient space between wall and sheet for laying of cables complete all as directed.

S&F 20mm bore galvanized iron tubes, medium grade, with all fittings laid in trenches all as specified and directed.

S&F 20mm bore gun metal gate valve heavy duty ISI marked with iron wheel head screwed both ends to iron pipes and fixed all as specified and as directed

Rounding to edges of exposed kota stone slabs of thickness 40-45mm, on one edge as in steps, cooking platform and other similar situations all as specified

M&L for three coats of white wash on newly plastered wall surfaces including necessary preparation of surfaces all as specified and directed.

SREE BALAJI ENTERPRISES

Vinayaka Enterprises

K T ASSOCIATES

PRAGATHI BUILDERS