PROVISIONING OF HT VCB PANEL FOR INCOMING SUPPLY TO TOWNSHIP AT 33KV SUB-STATION ALONG WITH ASSOCIATED CIVIL WORKS

Supplying and application of two coats of damp proof water proofing coat using an Acrylic elastomeric waterproof coating suchas Asian paints Smartcare Damp proof or equivalent product approved by EIC (Asian paint/ Dr fixit/ Sika) applied over throughly cleaned roof surface by removing laitance, dust, loose particles, grease etc using wire brush and water jet if required, repairing all cracks ,undulations, damaged portions with crack filler as per manufacturers recommendation. Application of one coat of primer as recommended by manufacturer and applying 2 or more coats of waterproofing coating using brush, roller including treatment of junctions, fillets, parapet walls,rain water outlets.Each coat shall be dried adequately before application of second coat complete with rates including ost of materials, labour, transportation, preparation, crack treatment, primer, loading, unloading and all other incidental charges. (Warranty for water proofing work to be given for 5years)

Removal of existing rolling shutter of size 3x4m with holdfast, guidrails and anchors etc which includes cutting lathes, plastering and brick wall wherever if required and making the surface neat and finish, as directed by EIC. The rate shall include for cost of materials,tools, labour charges, taxes,etc

Providing and fixing in position (at any ht.& level) two track glazed, Aluminium powder coated sliding windows with sections conforming to JINDAL catalogue including providing & fixing 4.80mm thick plain float glass of MODI / SAINT GOBAIN make with approved quality rubber / nylon gaskets, providing and fixing standard Aluminium 75mm handles, locking arrangement, necessary wheel / rollers etc.,. The windows shall be fabricated with Aluminium extrusions as described below of series B: a) Bottom member two track section 61.85 x 31.75 x 1.20 mm. b) Top & sides of two track section 61.85 x 31.75 x 1.30mm. c) Shutter top & bottom 40 x 18 x 1.29mm d) Shutter interlock 40x27x 1.29mm e) Shutter handle side 40 x 18 x 1.29mm complete with rates including cost of material ,tools, labour, transportation etc., all as directed and specified by EIC. [Gaps between wall / beam and Al. member shall be filled with sIlicon and made good].

Supplying and fixing manually operated rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. (80x1.25 mm M.S. laths with 1.25 mm thick top cover. )

Providing and fixing ball bearing for rolling shutters of approved make including cost and conveyance of all materials to work site and all other operational and incidental charges, labour and lift charges, all as specified and directed by EIC.

Extra for providing grilled rolling shutters manufactured out of 8 mm dia M.S. bar instead of laths as per design approved by Engineer-in- charge, (area of grill to be measured).

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m: All kinds of Soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

Providing and laying in position cement concrete PCC (1:3:6) with cost including rates of materials, tools, transportation, leads, lifts etc., complete as per direction of Engineer - in- charge.

Providing and laying in position cement concrete PCC1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) with cost including rates of materials, tools, transportation, leads, lifts etc., complete as per direction of Engineer - in- charge.

Providing and laying squared coursed rubble stone (CRS) masonry (second sort) of approved size in CM 1:6 proportion for foundations and basement with splays and cutting built in proper bond, properly hearted, interstices filled with mortar and bond stones placed at every spacing of 1.5m in each course including leads, lifts and all other incidental and royalties operational charges etc. complete as directed by the EIC

Brick work with non modular fly ash bricks with CM(1:6) conforming to IS:12894,class designation 10 average compressive strength in super structure above plinth level up to floor V level including rates of materials, tools, transportation, leads, lifts etc., complete as per direction of Engineer - in- charge.

Providing plastering by rendering 12 mm thick Cement mortar 1:6 (one part Cement : Six parts fine sand) over concrete / brick surfaces like ceiling, walls etc.,wherever required and finishing smooth and even, using trowel with all necessary scaffolding at all heights, etc., complete with rates including cost of all material, tools, labour, wastages etc., all as directed and approved by EIC.

Providing and fixing structural steel frame (for dry cladding with 30 mm thick gang saw cut with machine cut edges sand stone) on walls at all heights using M.S. square/ rectangular tube in the required pattern as per architectural drawing, including cost of cutting, bending, welding etc. The frame work shall be fixed to the wall with the help of M.S. brackets/ lugs of angle iron/ flats etc. which shall be welded to the frame and embedded in brick wall with cement concrete block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size) of size 300x230x300 mm, including cost of necessary centring and shuttering and with approved expansion hold fasteners on CC/RCC surface, including drilling necessary holes etc with all necessary scaffolding at all heights, complete with rates including cost of all material, tools, labour, wastages etc., all as directed and approved by EIC.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /seIf tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with all necessary scaffolding at all heights, complete with rates including cost of all material, tools, labour, wastages etc., all as directed and approved by EIC.

Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with Zinc coating 120 gram per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete with all necessary scaffolding at all heights, complete with rates including cost of all material, tools, labour, wastages etc., all as directed and approved by EIC.

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads& lifts, all complete as per direction of Engineer -in-charge.

Providing and fixing vitreous china urinal of Parryware Magnum model / Hindware/ Cera make with C.I. Hangers, 32 mm C.P. brass waste coupling , 3 bolts, nuts, screws etc., complete including cutting and making good the walls, and floors, where required complete with rates including cost of material, labour charges, tools, lifts, leads etc., all as approved, specified and directed by EIC.

Providing and fixing on wall face unplasticised Rigid PVC pipes of 110mm dia prince/sudhakar make conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, (i) Single socketed pipes for using as sewer line and rain water pipe fixing with clamps where ever required all as directed by EIC.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) (KAJARIA / NITCO / JHONSON ) make conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete with rates including cost of material, labour charges, tools, lifts, leads etc., all as approved, specified and directed by EIC.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), (KAJARIA / NITCO / JHONSON ) make conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete with rates including cost of material, labour charges, tools, lifts, leads etc., all as approved, specified and directed by EIC.

Supply & installation of Cast iron bench with FRP trips includlng civil wo rks, tra sportation and other overheads, etc all as approved, specified and directed by EIC. (Length (approx) 05', width(approx)-02', Height (approx)-03'

Providing and laying Ceramic matt finished/ anti-skid floor tiles of size 300x300 mm - 7-9mm thickness of 1st quality conforming to IS : 15622 of (KAJARIA / NITCO / JHONSON ) make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete with rates including cost of material, labour charges, tools, lifts, leads etc., all as approved, specified and directed by EIC

Providing & laying of 8-10mm thick ceramic tile dado/wall tiles of size 300mm x 450mm of (KAJARIA / NITCO / JHONSON ) or equivalent make as approved by EIC in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete including pointing/fixing the jointing with joint fillers of matching color/shade of tiles including cost and conveyance of all materials and water to work site including cost of base coat, all operational, incidental, and labour charges such as mixing mortar, fixing in position, including lift charges, curing etc., complete for finished item of work in all floors all as approved, specified and directed by EIC

Supplying and apply two coats of Wall painting with premium interior acrylic emulsion paint of asian/berger male over a coat of water thinnable cement primer on the prepared wall surface of asian make having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture including applying additional coats wherever required to achieve even shade and colour complete with rates including cost of material, labour charges, tools, lifts, leads etc., all as approved, specified and directed by EIC.

Applying priming coat :With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/steel works etc, complete with rates including cost of material, labour charges, tools, lifts, leads etc., all as approved, specified and directed by EIC.

Painting with synthetic enamel paint of approved shade of asian make and manufacture to give an even shade :Two or more coats on new work complete with rates including cost of material, labour charges, tools, lifts, leads etc., all as approved, specified and directed by EIC.

Providing and fixing fly proof galvanized M.S. wire of champion or equivalent approved make gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete: With 12 mm mild steel U beading etc, complete with rates including cost of material, labour charges, tools, lifts, leads etc., all as approved, specified and directed by EIC.

Providing, manufacturing and erecting Partly glazed and partly panneled single leaf Aluminium door using standard anodized powder coated sections of JINDAL, HINDALCO make as detailed below all of approved make.(Including necessaryews,fasteners,cleats,rods etc.Specification for each shutter :-a) Bottom members -97.30 x 44.45x 2.15mm b) Top members - 47.62x44.45x1.95mm c) Side member - 47.62 x 44.45 x 1.82mm d) Middle member - 49.91 x 44.45 x 1.60mm; Door member of SL NO19566 of JINDAL e) 12mm thick pre laminated twin finish exterior grade of Novapan MFPB (PTX) - Superior grade or TESA / ASIS / ARCHIDPLY or any other particle board having ISI Mark or 12mm thick both side finished MDF boards f) Glass - 5.00mm thick plain float glass of MODI / SAINTGOBAIN make g) Rubber gaskets - Good quality of approved make h) Glazing clips - Weight of 0.097Kg/RM. I) Aluminium hinges 125mm long - 3Nos j) Aluminium handle 150mm long - 2 Nos. k) Concealed lock of make godrej/sheel 4 lever l) Aluminium tower bolts 200mm long - 2 Nos. m)Miscellaneous -Al. cleats, screws ,Door sealant, etc

Providing and erecting partly glazed and partly panelled powder coated Aluminium partition using standard sections of JINDAL or HINDALCO so that each pannel shall not exceed 1.20 SQM with 12mm thick pre-laminated board having twin finish of Novopan / TESA in bottom rows and 5mm thick float glass of MODI / ST GOBAIN on middle and top rows including glazing clips, rubber gasket for fixing the glass, filling gaps with silicon sealant,strengthening the partition by taking the required intermediate vertical members up to roof lvel, etc. Specification for aluminum sections to be used is a) Bottom members -95.25 x 44.45x 2.0mm b) Top / vertical members - 63.50 x 38.10 x1.95mm c)Middle memebers - 63.50 x 38.10 x 1.95mm.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level of TATA/ VIZAG make complete as per direction of Engineer in Charge.

Providing and fixing 15mm dia Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability of Astral/ Ashirvad make for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

Providing and fixing 20mm dia Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability of Astral/ Ashirvad make for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

Providing and fixing 25mm dia Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability of Astral/ Ashirvad make for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

Supplying and fixing 100mm x 75mm diameter CI Nahani trap of Neco make with CP jally including finishing in CM 1:4 all as directed, approved and specified by EIC, complete with rates including cost of material, labour charges, tools, lifts, leads, transportation etc., all as approved, specified and directed by EIC.

Supplying and fixing white coloured glazed porceline European water closet (EWC) of Parryware/ Hindware / Cera make of with 'P' or 'S' trap with or without vent set, including supplying and fixing 10 Ltrs capacity valve less syphonic action type PVC low level cistern tip top model (E8303) confirming to IS: 7231 with brackets, double flapped anti microbial seat cover of durasheen model (E8292) confirming to IS: 2548 - Part 1 and 2, 40 mm dia PVC bend, 15 mm dia High density PVC inlet pipe connection, 15 mm dia CP angle stop cock with all above of approved make, colour etc. complete all as approved, specifed and directed by the EIC.

Supplying and fixing 40 mm dia CPVC rigid Pipe ISI mark with necessay elbows and bends etc suitable for drainage lines of approved quality including fixing, jointing, embedding in the wall etc., complete, with rates including cost of material, (MR) etc.,all as approved, specified and directed by EIC.

Supplying 150X150 mm SWG gully trap with CI cover along with suitable CI frame complete with rates including cost of material, labour charges, tools, lifts, leads, transportation etc., all as approved, specified and directed by EIC.

Providing and fixing factory made P.V.C. door frame of TATA pravesh/ SINTEX make of size 50x47 mm with awall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDMrubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineer-in-Charge. etc. including cost of all materials, labour for making ,fixing to the walls ,transportation, duties ,taxes etc. complete as directed and approved by EIC.

Providing and fixing factory made panel 30 mm thick pre laminated PVC door shutters TATA pravesh/ SINTEX make consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawing including cost of materials ,labour,taxes,duties and all other incidental charges as directed and approved by Engineer In Charge.

Supplying & Fixing 5 mm thick beviled edges with sideless with SS/CP screws/ studs etc looking mirrors of saint gobain / modi of size 600X450MM complete, with rates including cost of material, labour charge tools, lifts, leads, transportation etc., all as approved, specified and directed by EIC.

Supplying and fixing of 20mm dia gun metal gate valves of below mentioned dia, of ZOLOTO / LEADER make or equivalent approved make & quality complying to IS, having screwed ends including fixing to the pipe lines with teflon tape etc., complete, with rates including cost of material, labour charges, tools, lifts, leads, transportation etc., all as approved, specified and directed by EIC.

Providing and fixing wash basin of parry ware / hindware/ care make with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require (White Vitreous China Wash basin size 630x450 mm) with a single 15 mm C.P. brass pillar tap of approved make & quality complying to IS etc., complete, with rates including cost of material, labour charges, tools, lifts, leads, transportation etc., all as approved, specified and directed by EIC

Providing and fixing on wall face unplasticised Rigid PVC pipes of 75mm dia of prince/sudhakar make conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, (i) Single socketed pipes, complete with rates including cost of material, labour charges, tools, lifts, leads etc., all as approved, specified and directed by EIC.

Providing form works to sides of concrete foundations, footings, bases for columnns with including strutting,propping etc. and removal of form work complete with rates including cost of material ,tools, labour, transportation etc., all as directed and specified by EIC.

Providing and fixing C.P. brass angle valve of Hindware/parryware/essess make approved quality conforming to IS:8931 complete with rates including cost of material ,tools, labour, transportation etc., all as directed and specified by EIC.

Providing and fixing aluminium tower bolts ISI marked anodised of classic make (anodic coating not less than grade AC 10 as per IS : 1868 )of classic make transparent or dyed to required colour or shade with necessary screws etc. complete with rates including cost of material, labour charges, tools, lifts, leads etc., all as approved, specified and directed by EIC.

Providing and fixing SS hinges 100 mm of approved quality make complete with rates including cost of material ,tools, labour, transportation etc., all as directed and specified by EIC.

Providing and fixing 15mm 2way tap and health faucet of 1.20m long of approved quality of Hindware/parryware/essess make complete with rates including cost of material ,tools, labour, transportation etc., all as directed and specified by EIC.

Providing and fixing aluminium handles of 125mm ISI marked, anodised of classic make (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete with rates including cost of material, labour charges, tools, lifts, leads etc., all as approved, specified and directed by EIC.

Providing and fixing aluminium Aldrop of 250x16mm ISI marked anodised of classic make (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete with rates including cost of material, labour charges, tools, lifts, leads etc., all as approved, specified and directed by EIC.

Providing and fixing CP coated 15mm brass bib cock of approved quality of plumber/jaquar/essess make complete with rates including cost of material ,tools, labour, transportation etc., all as directed and specified by EIC.

Providing and fixing G.I. chain link fabric fencing ( Champion or equivalent approved make) of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. Made of G.I. wire of dia 4 mm, complete with rates including cost of material, labour charges, tools, lifts, leads etc., all as approved, specified and directed by EIC.

Sub-total Rs.

(A) Quoted percentage (Excess or below)

(B) Sub-Total Amount excluding GST Rs. [after considering percentage at (A)]

(C)Add 18% GST on Value on (B) in Rs.

(D) Grand Total : [ B+C] in Rs.

GST SAC Code No

Example: 1. If the contractor wish to quote 5% below estimated amount, then they need to enter "- 5 %" in Green colour Column against Quoted percentage (Excess or below) 2. If the contractor wish to quote 2% excess over estimated amount, then they need to enter "2 % " in Green colour Column against Quoted percentage (Excess or below)

HINDUSTAN AERONAUTICS LIMITED

AVIONICS DIVISION

HYDERABAD - 500 042.

Pre-Qualification Profile (To Be uploaded along with Part A)

Tender Notice No.:

Estimated Amount in Rs.

Tender Notice Date:

Tender Submission Date:

Name of the Individual / Firm / Company: * Mandatory

Type of ownership

If Other, please specify

Details of Constitution or Legal Status such as certificate of incorporation, shops and establishments, Contractor registration No etc.,

Address for correspondence:

GST NO.:

PAN No.:

Contact details

Contact person name

Designation

Mobile No.

Ph. No. with STD code

FAX No. with STD code

Email Id :

Average annual financial turn over during the last 3 years, ending financial year 2025 [ should not be less than 30% of Amount put to tender]. Turnover for 3 years are compulsory.

2022-23 (Ending on 31-03-2023) Rs.

2023-24(Ending on 31-03-2024) Rs.

2024-25 (Ending on 31-03-2025) Rs.

Average annual Financial turn over

Avg Annual Turnover criteria is not met

ESI & PF Nos with proof (If any)

ESI Registration No/. with proof if any

PF Registration No. with proof if any

Bank(s) details: [Copy of the cheque leaf to be uploaded]

Bank Account No.

Name of the Bank

Type of Account

Branch, Place

Bank Code No.

MICR No.

ECS No.

IFS Code No.

Latest Bankers Solvency Certificate from Nationalized/ scheduled Bank issued NOT before 12 months from the date of Tender submission.

Name of Bank & Branch

Date of Issue [MM/DD/YYYY]:

#VALUE!

Value in Rs.

Solvency value is NOT as per NIT. Submit required value Solvency

Experience of having successfully completed similar works during last 7 years ending last day of month previous to the one in which applications are invited. [Latest work experience certificate may be uploaded] (i) THREE similar completed works each costing not less than the amount equal to 40% of the estimated cost. (ii) TWO similar completed works each costing not less than the amount equal to 50% of the estimated cost. (iii) ONE similar completed work each costing not less than the amount equal to 80% of Amount put to the tender.

Completed similar works during last 7 years

Work NoI

Brief Description of Work:

Completed value of Work in Rs. :

Date of Commencement of Work [MM/DD/YYYY]:

Date of Actual Completion of Work [MM/DD/YYYY]:

#VALUE!

Work No II

Brief Description of Work:

Completed value of Work in Rs. :

Date of Commencement of Work [MM/DD/YYYY]:

Date of Actual Completion of Work [MM/DD/YYYY]:

#VALUE!

Work No III

Brief Description of Work:

Completed value of Work in Rs. :

Date of Commencement of Work [MM/DD/YYYY]:

Date of Actual Completion of Work [MM/DD/YYYY]:

#VALUE!

Details of person holding the power of Attorney (If different from contact person)

Position

Mobile No.

Ph. No. with STD code

FAX No. with STD code

DECLARATION I

The document being viewed / downloaded from the website and having read & understood all the contents of the tender document mentioned under terms and conditions including price bid do hereby accept all the terms and conditions laid down in the said Tender document and will abide by the same on acceptance and award of work.

DECLARATION II

I/We declare and confirm that - 1. All information and attachments submitted along with this offer are true and correct. 2. I/We are aware that any false information provided herein will result in the rejection of my offer . 3. I/We shall not make refund claims of expenditure incurred in processing this offer. 4. I / We aware that document sought only be uploaded for evaluation of offer. 5. I/We have not imposed any condition in price bid, I/We have not modified any part of tender documents issued by HAL.