CERTAIN REPAIRS TO OTM ACCN AND MD ACCN ALONGWITH HARDYAL ROAD AND KORA ROAD INCLD PERIODICAL SERVICES AND DBN VIHAR, HUDSON LINE INCL MAP HUDSON LINE AND MH COLONY, MAP JINDAN OLD ACCN UNDER AGE B R II OF GE (EAST) JALANDHAR CANTT

Amount

Taking down cement plaster of any description thickness including raking out joints hacking for key scrubbing down with water complete all as specified and directed.

M&L for 15 mm thick cement mortar 1:6 on brick or concrete surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparing new plastered surfaces of walls by applying two coats of oil bound distemper over a coat of primer and one coat of birla white putty complete all as specified.

M&L for 15mm thick cement plaster on brick or concrete surfaces in cement mortar (1:4) mixed with integral water proofing compound in the proportion recommended by manufacturer, surfaces finished fair and even complete all as specified and directed. (WPC shall be measured and paid separately under appropriate item of this BOQ).

M&L for preparation of new surfaces of walls including cornices, plasters etc (Plastered or unplastered surfaces) and applying two coats of cement base paint complete all as specified and directed

Supply only integral water proofing compound all as specified and directed.

M&L for plastering 5mm thick in cement mortar (1:3) finished even and smooth without using extra cement as on ceiling complete all as specified and directed

M&L for three coats of white wash on newly plastered surfaces of ceiling including preparation of surfaces complete all as specified and directed.

M&L for preparation of old surfaces of walls including cornices, plasters etc (Plastered or unplastered surfaces) and applying one coats of cement base paint complete all as specified and directed

M&L for complete removal of existing treatment of walls by sander, washing, rubbing down and stopping of distempered and painted surfaces and applying two coat of cement based paint complete all as specified and directed

M&L for preparation of old decorated surfaces of walls, washing rubbing down and stooping of distempered and painted surfaces and applying one coat of oil bound distemper complete all as specified and directed

M&L for preparation of old surfaces of walls including brooming down or steel wire brushing; scraping down smoke soot, moulds, moss and efflorescent and trading oil and greasy spots etc (Plastered or unplastered surfaces) and applying one coat of oil bound distemper with filling uneven surface by white wall putty complete all as specified and directed

M&L for complete removal of existing treatment of walls, washing, rubbing down and stopping of distempered and painted surfaces and applying two coat of oil bound distemper over a coat of primer over and a coat of wall putty complete all as specified and directed

M&L for preparation of old surfaces of walls including brooming down or steel wire brushing; scraping down smoke soot, moulds, moss and efflorescent and trading oil and greasy spots etc (Plastered or unplastered surfaces) and applying one coat of white (lime) wash complete all as specified and directed.

Ditto all as per item No 14.00 abovee but one coat of white wash on ceiling co,plete

M&L for hacking out old broken glass (any thickness, size quality or description) from wooden or steel frame glazed with putty or fixed with beads complete all as specified and directed

S&F sheet glass ordinary quality 3.0 mm thick in square not exc 0.50 Sqm each pane glazing with oil putty, clip in metal frame and wooden beading in wooden frame complete all as specified

Dismantling floor hearth or wall tiling including cement mortar bedding ( but not backing) and disposal of rubbish outside MD land complete all as specified and as directed.

M&L for non-skid ceramic coloured tiles (premium quality) 7 to 8mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors set and jointed in neat cement slurry and pointed in while or coloured cement to match over and including 15mm thick bedding layer CM 1:6 in complete all as specified

M&L for non-skid ceramic coloured tiles (premium quality) 7 to 8mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors set and jointed in neat cement slurry and pointed in while or coloured cement to match over and including 15mm thick bedding layer CM 1:6 complete all as specified

Ditto all as per Srl item No 20.00 above but on vertical surfaces such as dado, skirting etc over and including 10 mm thick cement plaster finished even and rough to receive tiles in Cement mortar (1:4) complete all as specified

M&L for non-skid ceramic coloured tiles (premium quality) 7 to 8mm thick(Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors set and jointed in neat cement slurry and pointed in while or colored cement to match over and incl 15mm thick bedding layer CM 1:6 in roughening of old concrete floor surfaces by picking, sweeping clean and washing down with water to remove dust inc brushing neat cement slurry with 3 kg/sqm complete all as specified.

All as per Srl Item No. 22.00above but in skirting and 10mm thick rendering as backing coat of CM 1:4 complete all as specified and directed .

M&L for 25mm thick cement concrete (1:2:4) type B-1 (12.5 mm graded aggregate) to receive the top layer of tiles complete all as specified and directed

M&L for coloured glazed tiles (premium quality) of size 450x 350x7 mm thick fixed with neat cement slurry in vertical surface to wall pointing in white/coloured cement to match over and including 10mm thick rendering in CM 1:4 complete all as specified and directed.

M&L for coloured ceramic glazed tiles (premium quality) of size 300x200x7mm thick as in skirting, dado & vertical surface, fixed with neat cement slurry in vertical surface to wall ,pointing in coloured cement to match over and incl 10mm thick screed in CM 1:6, complete all as specified and directed

S&F 18 to 20mm thick granite (of any type) tiles machine cut , in skirting/dado laid over cement screed 10 mm thick in CM 1:4 and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing and dismantling of existing granite complete all as specified and directed

Demolition of reinforced cement concrete in ground floors and paving n.exc 15 cm thickness (reinforcement to cut as required to facilitate demolition)complete all as specified and directed

M&L for reinforced cement concrete (1:2:4) type B-1 (20 mm graded aggregate) slab supported on wall, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed

M&L for MS TMT bars 10 mm and over dia and cut to length, bent to shape required including cranking bending spirally for hooping for clos hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed

M&L for form work to soffits of suspended slabs such roof slabs, floor slabs, shelves, landings and similar work, not exceeding 200mm thick (horizontal or slopping) rough finished surfaces of concrete flat or shelfs etc. complete all as specified and directed.

Use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n. exc. 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc. 10cm but n. exc. 20cm wide for rough finished surfaces of concrete complete all as specified and directed.

Taking down chowkhats or frame with shutter w/o taking off shutter from the frame area not exc 1.5 Sqm each all as specified.

Ditto all as per srl item No. 33.00 above but area exc 1.5 Sqm and not exc 4 Sqm each, complete all as specified.

Taking down shutters of any description exc 1 Sqm and not exc 2 Sqm each complete all as specified and directed.

M&L for framed work as in doors or gates of angle or other section with gusset plates, hold fast rails, braces, etc, complete, drilled for fixing of steel sheeting or other covering. Doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings ( exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing complete all as specified and directed.

S&F pressed steel frames 125x60mm as per IS for door with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc including PCC 1:5:10, type B0 (20mm aggregate) filling in steel frame complete all as specified

Ditto all as per Srl item No. 37.00 above but 105x60mm size

S&F for 40mm thickness of factory made flush shutter solid core construction with block board core & ply wood face panels, commercial type on both side including 40 x 6 thick 2nd class Hard wood lipping on edge, complete all as specified and directed.

S&F 2nd class hard wood 35mm thickness of factory made plain framed, paneled shutter(one or two panel) with lock rail and panel of 9 mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and directed

S&F 35mm thick 2nd class hard wood glazed or Skelton shutter factory made open rebated prepared to receive glass, gauge etc without sash bars edges of framing plain fitted with cut and mitered beads for securing glass etc size of member all as per clause 8.23 (a) of SSR Part-I complete all as specified and directed.

S&F steel window 1.25 mm thick Box type (Primer coated) ERW hollow P section of size 60 mm x 25 mm comprises glazed and gauzed skelton shutter EWR sec 50 mm x 20 mm and 1 mm thick and two openable leaf consisting two Nos sash bar of T- section 20 mm x 3 mm complete welded to frame with one vertical mullion of EWRR box type T- section of size 60 mm x 25 mm and 1.25 mm thick including cuttings holes and making good dismantled portion in PCC (1:2:4) type B-1 four Nos for each window including following fittings welded to failed shutters:- (a) Hold fasts 150 mm long of 12 mm x 3 mm made to shape-04 Nos per window. (b) Handle of Z sec 20 mm x 25 mm, 100 mm long-1 No of leaf (c) MS tower bolt 150 mm long 02 Nos per leaf. (d) Z sec 20 mm x 25 mm , 100 long of hollow square 15 mm x 20 mm x 63 mm welded to hinges – 01 No per leaf (e) MS pintal hinges of size 75mm x 12 mm -02 Nos per leaf (f) Fabrication and fixing arrangement as per drawing No CEJZ/TD -06/07. Note:- Glass, wire mesh and painting shall be measured and paid separately under appropriate items

Ditto all as per Srl item No. 42.00 above but in gauged shutters without sash bars

Ditto all as per Srl item No. 42.00 above but in ventilators

M&L for powder coated aluminium door shutter having 150mm x 44mm x 2.85mm thick bottom rail, 150 mm x 44mm x 3mm thick middle rail, 100mm x44mm x2.85 mm thick stile and top rail including necessary fitting joinery cleat, glazing packing snap beading 10 mm x 10 mm , Powder coated aluminium handle 200 mm long (02 Nos) , 3 Nos 100 mm size chromium plated butt hinges, 2 Nos 200mm size Alu tower bolt and Aluminium body hydraulically door closer , designation No-3, universal type, weight between 61 to 80 kg etc including frame of section 100 mm x 44 mm x2.85 mm and door shutter, bottom portion covered with 9mm thick pre-laminated particle board, interior grade, pre-laminated on both sides with decorative choice lamination (colour/design approved by Engr-in-Charge) fixed to Aluminium frame work and top portion covered with 5.00 mm thick tinted glass and pattern, one mortion lock (Make: Harrison ) with shutter and fixing including taking down of existing Chowkat with Shutter complete all as specifies and directed by Engineer-in-Charge. Make of aluminium section Hindalco/Jindal

M&L for powder coated aluminium window shutters (Glass shutter and wire gauge shutter) side hung having 75 mm x 44 mm x 2.85 mm thick stiles bottom rail and top rail including necessary ftting joinery cleat glasing packing snap beading 10 mm x 10 mm , 4 x nos of anodised aluminium handle 150 mm size, 8 x nos of chromium plated butt hinges 75 mm size and 4 x nos of 100 mm long Alu tower bolt etc inlcuding frame of section 100 mm x 44 mm x 2.85 mm and including 5.00 mm thick tinted glass and including aluminium grill and fixing including taking down of existing Chowkhat with Shutter complete all as specified & directed by Engineer-in-Charge. Make of aluminium section Hindalco/Jindal

M&L for Anodized aluminium window/ ventilator shutter side hung having 75 mm x 44 mm x2.85 mm thick stiles bottom rail and top rail including necessary fitting joinery cleat glazing packing snap beading 10 mm x 10 mm , 2 Nos of anodised aluminium handle 150 mm size, 2 Nos of chromium pated butt hinges 75 mm size and 2 nos of 100 mm long aluminium tower bolt etc including frame of section 100 mm x 44 mm x 2.85 mm and including 5.00 mm thick tinted glass and including aluminium grill and fixing including taking down of existing Chowkat with Shutter complete all as specified & directed by Engineer-in-Charge. Make of aluminium section Hindalco/Jindal

S&F framed work such as grills, gratings, etc .with ends of bars shouldered and/ or riveted , or forget into spikes ; framed guard bars parallel iron doors and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed

M&L for 3.00 mm thick glass sheet, ordinary quality and glazing with oil putty in square n.exc 0.5 sqm in each pane complete all as specified and directed

M&L for 3.00 mm thick figured glass, pin head type and glazing with oil putty in squares not exc. 0.5 sqm in each pane complete all as specified and directed

S&F in repair factory made built-in steel cup board with pressed steel frame and pressed steel shutter 1.00mm thick fixed to masonry wall by hold fasts, made out of 25x3mm flat iron including MS hanging rod of 20mm dia with brackets fixed on inner side of cupboard, provn of MS peg set 3 pegs fixed on inner side of shutter and 1.00mm thick black sheet 3 Nos shelves as shown in Drg including spray painting with two coats of synthetic enamel paint over one coat of red oxide primer all around on steel surfaces of frame and shutter and fixing in PCC (1:2:4) all as directed and shown on Drg No CEJZ / TD-1104/08 Sheet 1/2 to 2/2, including dismantling of shelves/shutter etc complete all as specified and directed.

S&F Hasp & Staple aluminium 100 mm , including bolt to hinge plate and fixed with screws with Cup Board shutter all as specified

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. Tubes for top & bottom rails M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, fixing in the frame at the site as per specification & drawing

S&F PVC solid door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawing

S&F floor door stopper 140mm of aluminium alloy body and tongue anodized with hard drawn steel spring fixed in floor all as specified and directed by Engineer-in-Charge

S&F galvanized mild steel wire cloth 0.56 mm nominal dia and average width of aperture 1.18 mm and fixed with tinned tacks complete all as specified and directed.

S&F in repair galvanized mild steel wire cloth 0.56 mm nominal dia and average width of aperture 1.18 mm and fixed with tinned tacks complete all as specified and directed.

S&F 250mm long mild steel sliding door bolts stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified.

S&F 100mm size butt hinges medium weight cold rolled mild steel all as specified

S&F100mm size stainless steel butt hinges for fixing to PVC doors all as specified.

S&F 200mm long mild steel tower bolt stove enamelled black with bright bolt all as specified.

S&F 150 mm mild steel pressed handles oval type, stove enamelled black all as specified.

M&L for preparation of new wood surface of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified

M&L for preparation of old wooden surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed

M&L preparation of new or previously untreated steel surfaces of any description, n. exc. 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

M&L for preparation of old steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed

S&F aluminium anodised tower bolts 200 mm size fixed with machine screws complete all as specified and directed.

S&F aluminium anodised Bow Handles 150 mm size fixed with machine screws complete all as specified and directed.

S&F mild steel 300mm ordinary rat tail rod pattern springs including roller and roller plate welded to steel frame/ screwed to wooden frame complete all as specified and directed.

M&L for Galvanised iron water tubing 15 mm bore, medium grade with & including all fittings fixed to wall, ceilings and or laid in floors etc including taking down the existing tubing complete all as specified

Ditto all as per srl item No. 70.00 above but for 20mm bore tube complete

S&F in repair Stop valve,15 mm cast copper alloy chromium plated fancy type with long shank & cup (concealed type) with capstan heads, screwed down, high pressure, with crutch or butterfly handle screwed for 15mm bore iron complete all as specified and directed.

S&F in repair 15mm angle stop valves, cast copper alloy, chromium plated, screwed down, high pressure with crutch or butter fly handle screwed both ends for iron pipe or for unions and complete all as specified and directed.

S&F in repair Bib tap chromium plated, cast copper alloy suitable for 15mm bore iron pipe with long body fancy type complete all as specified and directed.

S&F squatting pan WC Orissa pattern size 580 x 440 mm white with integral foot rest with P or S trap including provn of lime concrete bedding including breaking up existing damaged WC seat and connecting flush pipe etc and make good to floor complete all as specified and directed

S&F in repairs Vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern) including seat cover and flushing pipe for pedestal pipe etc. complete all as specified and directed

S&F in repair seat cover for water closet pedestal pattern all as specified

S&F in repair PVC valveless, syphonic action type flushing cistern low level white with inlet ball valve float and handle, 10 ltr capacity including brackets complete all as specified and directed

S&F in repair PVC connection fiber, reinforced 45cm long with brass check nut and PVC washers at both ends complete all as specified and directed

S&F in repair health faucet (ABS body)mild steel chromium plated suitable for 15mmdia pipe with 1.25m long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed

S&F in repair Soap dish stainless steel chromium plated fixed with brass screws and rawl plug complete all as specified .

S&F in repair acrylic corner set of 3 pieces (Size - 11", 9" & 7" and minimum thickness 5mm) as per sample approved by Engineer-in-charge all as specified and directed

S&F in repair 500 ltr UV protected antimicrobial rotational moulded polythylene water storage tank (white) (Cylindrical vertical with closed top) hosted and fixed in position with 20mm ball valve high pressure, PTMT with polythene float and fly nut including dismantling of existing tank of any description complete all as specified

S&F in repair 1000 ltr UV protected antimicrobial (white) rotational moulded polyethylene water storage tank (cylindrical vertical with closed top)including dismantling in any type and in any position hoisted and fixed in position with Unions, Tank Nipple and other fitting, ISI Marked all as specified and directed

S&F in repair 20mm for ball valve high pressure, PTMT with polythene float and fly nut complete screwed for iron pipe or brass ferrule and fixed in repair complete all as specified and directed

S&F in repair 20mm for ball valve brass high pressure, with polythene float and fly nut complete screwed for iron pipe or brass ferrule complete all as specified and directed

S&F in repair Pillar tap (Swan Neck), cast copper alloy, with capstan heads, 15mm bore dia of pipe chromium platted screwed down high pressure with long screwed shanks and fly nuts screwed for iron pipe complete all as specified and directed.

S&F in repair for Pillar tap (Swan Neck) cast copper alloy, with capstan heads, 15mm bore dia of pipe chromium platted screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts screwed for iron pipe complete all as specified and directed

S&F in repair brass chromium plated shower rose of 125mm size, with or without swivel joints including fixing to steel pipe (min size 300 mm) or union complete all as specified and directed.

S&F in repairs Vitreous china wash hand basin , white, flat back 550x400mm including one number brass CP waste coupling ,32mm dia , PVC waste pipe with connector , brackets 2 Nos including cutting for and pinning in ends of brackets complete all as specified

S&F in repairs sinks with drainage board made of stainless steel 1 mm thick kitchen with plugs, washers, waste coupling and waste pipe, overall size 915 mm x 460 mm bowl size 410 mm x 330 x 160 mm including bedding in CM on dwarf wall or incl fitting cantilever brackets and connection union to pipe complete all as specified and directed

S&F in repairs for sinks with drainage board made of stainless steel 1 mm thick kitchen with plugs, washers including cantilever cast iron brackets, connecting union ,waste coupling and waste pipe overall size 495 mm x 420mm with bowl size 410 mm x 330 x 160 mm complete all as specified and directed

M&L for mild steel pipe 25 mm dia curtain rod with PVC coating fixed in the MS hooks, and finials/side brackets (both side), shade fixed in repair all as specified.

M&L for PVC (SWR) floor trap with grating including jointing to waste pipe fixed with solvent cement (diameter of outlet in 75mm) including taking out damaged floor trap in any type and position complete all as specified and directed

Cleaning of floor trap and applying of cement around the floor trap with sealant compound for arresting the seepage at any circumstances (Kitchen, Bathroom and Toilet) all as specified and directed by Engineer-in-Charge. Make:- WACKER SILICONES (GP Silicone Sealant )

S&F in repair flexible PVC Waste pipe of approved quality 32 bore, 75 cm long with one end socketed fixed to waste coupling, compete all as specified and directed

S&F PVC (SWR) pipes with single socketed in any length with rubber ring joints fixed on brick walls or laid in trenches with PCC 1:4:8 complete houching with bedding 110 mm dia including demolition and braking up existing pipes with fittings complete all as specified and directed.

Ditto all as per srl item No. 98.00above but 75 mm dia

S&F PVC (SWR) bends 110 mm with access door complete all as specified and directed.

Ditto all as per srl item No. 100.00above but 75 mm with access door

S&F for 110mm PVC (SWR) vent cowl complete all as specified and directed.

S&F Brass chromium plated tubular towel rail 20mm dia , D type, 60cm long between flanges in repairs complete all as specified and directed

S&F in repair CP grating 125mm dia with centre hole all as specified and directed by Engineer-in-Charge

Demolition of brick work as in walls/parapet walls removing grass fungus weed, roots of trees completely, grown on roof/wall surfaces, complete all as specified and directed.

M&L for brick work with sub class 'B' old size bricks straight or curved on plan exc 6 M mean radius built in CM (1:6) all as specified.

Ditto all as per srl item No. 106.00 above but except bricks

Demolition of brick tiles single layer as in roof covering complete all as specified

Demolition of mud in roofs any thickness including plastering and leeping (whether full thickness removed or only a part thereof) all as specified

M&L for PCC (1:2:4) type B-0 (using 12.5mm graded stone aggregate) as in benching, roof padding, roof kerbs or mud stops, coping etc rounded or chamfered on edges complete all as specified and directed

M&L for 10mm thick cement plaster in cement mortar (1:3) mixed with integral water proofing compound in the proportion recommended by manufacturer, on concrete roof surfaces finished even and fair, including cleaning the roof top by scraping down with water etc all as specified and directed by Engineer-in-Charge (WPC shall be measured and paid separately under appropriate item of this BOQ).

M&L for Brushing neat cement slurry with 3 kg of cement per sqm complete all as specified and directed

M&L for Bitumen Primer shall be applied on plastered surface of roofs at the rate of 0.40 Kg/Sqm of Surface area of roof for use in water proofing and dump proofing treatment complete all as specified and directed

M&L for Painting the roof surface with a coat of hot blown paving industrial bitumen 85/25 as a bonding material in two coats one on primed surface & 2nd on APP based polymeric membrane at the rate of 1.20 kg/sqm complete all as specified

M&L for APP based polymeric membrane minimum weighing 3 Kg/sqm and minimum 3mm thick reinforced with five layer polyster non wove fabric ( wt. Not less than 150 gms/sqm) laid on primed surface by forced application complete all as specified

M&L for 40 mm thick brick tiles with 15 mm thick bedded layer of 1:3 CM laid on 2nd bitumen coated surface and joints grouted flush mortar 1:3 mixed with 5% of crude oil by weight of cement, complete all as specified .

Ditto all as per Srl Item No 116.00 above but except brick tiles

M&L for Cutting out cracks to V-section in existing RCC roof slabs or terracing , cleaning out & filling solidly with a hot mixture of bitumen and clean dry sand 1:1 ( by weight) all as specified

M&L for repairing of R.C.C projections, chajjias, roofs, facia and ceiling etc by necessary preparation. Scarping, cutting, chiselling derusting and cleaning exposed reinforcement, surfaces of damaged, loose R.C.C surfaces with cement concrete (1:1.5:3) using 12.5mm graded crushed stone aggregates and reinforcement with welded mesh of weight exc 2 kg per sqm but n.exc 3kg/sqm (if reqd) with or without facia and finished with cement and sand mortar (1:3) using coarse sand necessary form work and applying two coats of finishes to match with the existing surfaces in at any height complete all as specified and directed by Engineer-in-Charge

M&L for flush pointing in cement mortar 1:3 on brick tiles laid flat including racking out joints/ pointing, hacking for key, scrubbing down with water complete all as specified

M&L for Water proofing treatment to sunken floors of kitchen, toilets, laboratories, bath and WCs etc shall be as under:- (i) Application of Two component acrylic modified cementitious coating (aa) The surfaces to be applied shall be completely dry and free from containments such as dirt, dust, oil, surface treatments and old coatings. Concrete substrates must be mechanically prepared using abrasive blast cleaning or milling to remove cement laitance, existing coating and achieve a gripping profile that is clean, dry and free from laitance and dry other form of surface contamination. The installation instructions in manufacture's published literature should be strictly complied with, including but not limited to the following:- (bb) Chipping out any visible cracks in "V-Groove" pattern as applicable. Special attention on this part. Cleaning of cracks & then filling those cracks with SIKA latex SBR 100 putty/Dr Fixit 302 SBR latex/ Perma latex SBR/FOSROC Nitabond SBR latex/Asian paint latex as required. Final cleaning of surface with power grinder, wire brush, hair brush & vacuum pressure if required. (cc) Dampen all surfaces immediately ahed of application of Acrylic modified Cementitious coating of sika Top Seal-107/Brush Bond FOSROC/Dr Fixit/STP/CICO. (dd) Whilst the surface is still damp from saturation (S.S.D), apply one coat of Acrylic modified cementitious coating of SIKA Top Seal-107 /Brush Bond FOSROC/Dr Fixit/STP/CICO of viscosity as per manufacturer's instructions. (ee) Apply glass fabric sheet of SIKA Fab 1/FOSROC/Dr Fixit/STP whilst the first coat is wet.

(ff) Once touch dry, apply second coat of Acrylic modified cementitious coating of SIKA Top Seal -107 /Brush Bond FOSROC/Dr Fixit/STP/CICO of viscosity as per manufacturer's instructions on the entire area. (gg) Second coat shall be applied after 6-8 Hrs of application of previous coat and in the direction right angle to the previous coat. (hh) The waterproofing coating should be taken to a height minimum 300mm above the finished floor level on the vertical surfaces three sides including dismantling of existing tiles. (jj) It is essential to cure Acrylic modified cementitious coating immediately after application (minimum 6-8hrs drying) for a minimum of 3 to 5 days to ensure full cement hydration and to minimize cracking. (kk) A protection plaster 12-15mm thick) in CM 1:3 admixed with appropriate integral water proofing compound has to be applied on the walls. Admixture: SIKA Plastocrete Plus/FOSROC/DR Fixit/STP/CICO conforming to IS 2645. Providing and applying a protection screed of 50mm thick 1:4, cement sand mortar admixed with SIKA Plastocrete over the applied water proofing coating on horizontal surfaces. Admixture: SIKA Plastocrete Plus/FOSROC/DR Fixit/STP/CICO conforming to IS 2645. (ll) All the corners and joints should be pretreated with an elastic waterproofing sealing tape with a woven bonding mesh on each surface and an elastic expansions zone in the centre of Make SIKA Seal Tape/FOSROC/Dr Fixit/STP.

(mm) The membrane has to be protected in accordance with the manufacturer's recommendations until placement of concrete. The membrane to be inspected for damage just prior to concrete placement and make repairs in accordance with manufacturer's recommendations. (nn)Waterproofing treatment has to be carried out through applicators authorised by the respective manufacturer's and approved by GE. (ii) All the joints of pipes and traps within the sunken portion shall be sealed properly by epoxy sealant. (iii) All CI traps in sunken slab to be enclosed with PCC 1:1.5:3 (Min 15cm) all around. (iv) The sunken portion shall be filled with PCC 1:5:10 type E-2 (using 40mm stone aggregate) complete all as specified. (v) Providing drainage spout pipe GI pipe 40mm dia bore light grade upto outside of outer wall ( Approx 450mm to 600 mm long ) including cutting to existing wall and making good the disturbed surface complete all as specified and directed. (vi) Providing 25mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate as in flooring for laying floor finish all as specified. Note:-Item No 25 (iv) ,(v) &(vi) shall be measured and paid separately

M&L for Cement concrete 1:5:10 type E-2 (using 40mm stone aggregate) as in sunken flooring complete all as specified

S&F drainage spout pipe GI pipe 40mm dia bore light grade upto outside of outer wall (Approx 450mm to 600 mm long ) including cutting to existing wall and making good the disturbed surface complete all as specified and directed.

M&L for 25mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate as in flooring for laying floor finish all as specified

Demolition of cement concrete in ground floors and paving n. exc 15 cm thickness (below or above the ground level) complete all as specified and directed.

M&L for cement concrete type D-2, 1:4:8 (40mm graded aggregate) 75mm thick as in sub base of flooring complete all as specified and directed.

M&L for 75mm PCC 1:3:6 type C1 using 20mm graded aggregate as in plinth protection and path finishing the surfaces even and smooth with using extra cement with joint/panel filled grade 'A' bitumen compound complete all as specified and directed.

M&L for 75mm PCC 1:3:6 type C1 using 20mm graded aggregate as in plinth protection the surfaces even and smooth without using extra cement all complete all as specified and directed

M&L for chequered cement concrete tiles 30cm x 30cm x 25 mm thick set with grey cement and pigments jointed and pointed in neat coloured cement slurry in floors over and including 15 mm thick cement screed bed in cement mortar (1:6) including demolition of old tiles/concrete floor all as specified and directed

M&L for laying 60mm thick machine pressed precast concrete interlocking paver block and shape and size conforming to IS-15658-2006 of M-35 grade with grey cement and pigment including demolition of old paver blocks complete all as specified and directed. Note : The sample shall be got approved from the GE before build procurement and lots shall be got tested independently by the GE

Ditto all as per Srl Item No. 130.00above but except tiles complete

M&L for 25mm sand cushion, filling 30mm under floors or in foundations including watering and consolidation complete all as specified and directed

M&L for PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) as in sides of rounded or chamfered on edges of interlocking/ chequered tiles, bed block concrete complete all as specified and directed

M&L for chromium plated peg set of 5(PTMT), fixed with screws and plugging to rear side of door shutter in bath, complete all as specified and directed.

Uprooting of trees, grass, bushes etc from brick wall/roof tiles or any surfaces of bldg including dismantling the required brick work /roof tiles/mud concrete etc for uprooting the vegetation etc and make good the same to match existing surfaces with same material or concrete 1:2:4 type B-1 after pouring the chemical (which destroy the growth of vegetation to place where vegetation removed).The rate shall include for scaffolding or any other arrangement required during this process upto 10 mtr height complete all as specified

Cleaning of overhead tank of any description and any capacity descaling, washing complete with soap solution and removing vegetation around the overhead tank/plate form including opening and reconnecting with GI tubing and writing month of cleaning with stencil having 3 inch height as site requirement complete all as directed by Engineer-in-Charge

S&F Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc. wind ties for roof including securing bolts; complete all as specified and directed

S&F in repairs 20mm dia curtain rails, mild steel , chromium plated fixing in cup board with brackets, stops, rollers etc, all as specified

M&L for Roof trusses (framed), trussed, purlins, crane gantries, rails, post etc and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc of Fe-410-W(Gde-E-250 Quality 'A', including dismantling complete all as specified and directed

S&F stainless steel plate rack of superior quality size 2400mm 3600mm with not less than 8 kg complete all as specified and directed.

Dismantling of Asbestos cement (corrugated, semi-corrugated, etc.) sheets in roof coverings complete all as specified and directed

M&L for 6mm thick asbestos cement fiber, corrugated or semi-corrugated sheets fixed with L-type or J-type or cranked hook bolts in roofs, walls etc all as specified.

All as per Srl Item No. 142.00 but except sheets

M&L for Asbestos cement 6mm thick serrated ridge for corrugated or semi corrugated sheets fixed with L-type or J-type or cranked hook bolts in roofs, walls etc fixed in repairs all as specified.

S&F Pre-painted galvalume aluminum zinc coating AZ 150, GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified

S&F Pre-painted Galvalume Aluminum Zinc Coating AZ 150, GI based Plain Steel Sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, complete all as specified and as directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for complete all as specified

M&L for pre-cast RCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in Manhole cover slab set in CM 1:4 complete all as specified and directed

S&F TMT bars 8mm dia cut to length bent to shape required including binding with mild steel wire (annealed) not less than 0.9 mm dia, complete all as specified and as directed

M&L for complete removal of existing treatment of old decorated walls by sander, scraping down smoke soot, moulds, moss and efflorescent and trading oil and greasy spots etc (Plastered or unplastered surfaces) etc and applying two coats of acrylic exterior emulsion paint over a coat of wall primer applying by mechanical spray gun including filling uneven surface with putty complete all as per manufacturer instruction and as specified and directed by Engr-in-Charge

M&L for Dholpur stone as on wall cladding with machine cut face work, pillar, arches, hexagonal roof pillar and all facing etc of 15 mm to 18 mm thick one side single length laid and jointed in cement and sand mortar 1:2 including ardelite chemical with epoxy and recess pointing pointed with an admixture of white cement and dholpur stone dust 1:1 and making edges, work in small patches, stone shall be of uniform colour of each stone and size not exc. 0.20 sqm each fixed , over and including 15mm thick cement plaster in CM (1:4) on brick or concrete wall surfaces finished rough surfaces to receive tiles all as specified and directed

M&L for Vitrified Ceramic tiles light shade, (double charged) 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match colour tiles over and incl 15mm thick screed bed in CM 1:6 all as specified.

Ditto all as per Srl Item No. 152.00 above but in skirting and 10mm thick rendering as backing coat of CM 1:4 complete all as specified and directed .

M&L for 18 to 20 mm thick machine in cut kota stone slab flooring over and incl 15mm thick bedding layer CM 1:6 in roughening of old concrete floor surfaces by picking, sweeping clean and washing down with water to remove dust inc brushing neat cement slurry with 3 kg/sqm with pigments to match the shade of slab including cutting, rubbing and mirror/granite finish polishing including taking down old stone slab complete all as specified and directed by Engr-in-Charge.

Ditto all as per Srl item No. 154.00 above but on vertical surfaces such as skirting dado, riser etc over and incl 10 mm thick cement plaster in CM 1:4 rough finished surface to receive tiles

Dismantling structural steel work including door, gates framed trussed etc complete all as specified and directed .

Dismantling asbestos cement, plain or corrugated steel sheeting any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed .

S&F in repairs door closer hydraulically of aluminium extruded section body regulated, designation No-3, universal type, suitable for door shutters of 851 to 1000 mm in width and weight between 61 to 80 Kg and fixed complete all as specified

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/ slabs. blankets, any type, any thickness and any shape including cover fillets and frame work complete all as specified and directed .

M&L in repair for PVC hollow wall panelling 7 to 8mm thick colour/ design approved by Engr-in charge, inclusive of fixing to wall including moulding ends caps fixed with PVC sleeves and screws as required at site complete all as specified and directed.

S&F of armstrong mineral fibre acoustical suspended ceiling system with dune (Tegular) edge tiles with armstrong 24mm exposed grid. The tiles should have humidity resistance of 99%, NRC 0.5, light reflectance > 85% , thermal conductivity K = 0.052 - 0.057 w/m K, colour white, fire performance UK class 0/ class I (BS 476 pt-6 & 7) in module size of 600x600x16mm, suitable for green building application with recycled content of 32%. The tile shall be laid on Armstrong Prelude 32 with 24mm wide T section flanges colour white rotary stitching on all T sections i.e the main runner, 1200mm & 600mm cross Tees with a web height of 27mm and a load carrying of 7.1kgs/sqm and minimum pull strength of 100 kgs. The T section have galvanising of 90 grams per sqm and need to be installed with suspension system of Armstrong. All accessories manufactured and supplied by Armstrong world industries.

S&F Brass CP Wash hand basin Mixture with capstan heads, chromium plated, screwed down high pressure, with lettered "hot' or 'cold' with long screwed shanks and fly-nuts, screwed for iron pipes and fixed in repair for mixing hot &cold water screwed down for iron pipe and fixed complete all as specified and directed .

S&F in repair vitreous china Urinal, flat back , white, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, including and fixing of flush pipe, grating with waste coupling, and union for discharge pipe, waste pipe ,spreader etc, size of urinal 59cm x 39 cm x 37.5 cm all as specified and approved quality and directed by Engr-in-Charge. .

Cleaning the surface and made free of dirt, foreign particle, laitance followed by grinding all all protrusion to make surface modulated. Thereafter, inspection for cracks on the surface caused by thermal expiation contraction. Cutting the grooves with suitable cutter machine in V-groove filled with repairs mortar/ micro-concrete/ general purpose grout as recommended proportionally as per recommendation of manufacture. Making of Gollas at all the corners with polymer modified mortar (1:4) cement sand with 3.5% acylic of cement weight complete all as specified and directed.

Supply and applying high build elastomeric waterproofing coating based on pure hydrophobic polyurethane cold applied of spray/brush applied, membrane with an elongation of 280% and tensile strength of 2.7N/mm2 as per ASTM D 2370, crack bridging ability of 3mm, no leakage upto 5 bars of water pressure as per DIN 1048, min 88% solid content. The system includes final base preparation, epoxy primer 1:1 (Resin; harder) application with 100% water dilution and Pure polyurethane application in 2 coats with a total min consumption of 1.25 kg per Sqm. Application should be done with Graco sprayer by a company authorized applicator” complete all as specified and directed

M&L for 40mm thick PCC (1:2:4) type B-1 using 20mm graded stone aggregate as in sub floors, sub base, concrete surfaces finished fair & even to receive topping floor finish/layer complete all as specified & directed.

Supply & fixing glass dividing strips 3mm thick and 38mm wide inserted in position conforming to design complete all as specified and directed.

S&F Providing precast cement concrete louvres and jallies, 25mm thick (measured solid), PCC 1:2:4, Type B0 (12.5mm graded aggregate) including all mouldings with frame Set in CM 1:4 including dismantling/ demolition of existing louvers/ jallies complete all as specified and directed

Note for above work:- (a) Contr shall submit at least three samples of material for approval of GE. (b)Mke of sanitary fittings:- Jaquar/ Cera/ Ess-Ess (c)' Make of plumbring work:- Parryware/ Hindware. (d) Make of Non skid/ Glazed/ Vitrified tiles:- Kajaria/ Somany/ Orien bell. (e) Make of Galvalume sheets :- TATA Blue Scope/ JSW/ RINL. (f) After completion of work area shall be made clean all spot/ Moss/ Debris shall be removed from site without any extra cost of Govt.

SANMATI UDYOG (BID ID -3366164)

SANDEEP JHANJI CONSTRUCTIONS (BID ID -3365503)

S S CONSTRUCTION (BID ID -3374704)

Sanjiv Kumar (BID ID -3373960)