The Related to The Premises of The LMO Established at The Autonomous State Medical College, Kanpur Dehat, U.P.

The Related to The Premises of The LMO Established at The Autonomous State Medical College, Kanpur Dehat, U.P.

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. All kinds of soil

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. Concrete of M25 grade with minimum cement content of 330 kg /cum

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (including equivalent design mix)

Providing, fabricating and fixing M.S. protective bollard post of minimum 1200 mm height above finished ground level (FGL), fabricated from 114 mm outside diameter × 4 mm thick M.S. circular pipe, with 250 × 250 × 10 mm thick M.S. base plate, securely fixed with 4 Nos. 16 mm dia anchor bolts, including M.S. dome-shaped top cap, complete with 450 × 450 × 300 mm deep M20 grade RCC foundation, excavation, shuttering, reinforcement/anchoring as required, grouting and fixing of the post, welding, grinding and finishing, one coat of approved anti-corrosive primer followed by two coats of approved synthetic enamel paint, including provision of 100 mm wide yellow reflective bands/tape, all materials, labour, tools, tackles, transportation and incidental works, complete in all respects as per approved drawing, specifications and direction of the Engineer-in-Charge. The bollard shall be suitable for pedestrian and vehicle protection and industrial perimeter applications.

Providing and installing chemical earthing electrode consisting of GI pipe electrode of 50 mm dia × 3 m long or approved equivalent, with suitable earth enhancement compound/chemical compound and watering arrangement, installed vertically in an adequately sized earth pit, including excavation, supplying and filling of approved earthing compound around the electrode, connection of GI/Copper earth strip or wire with suitable GI clamps/bolts, GI funnel with wire mesh, watering pipe, masonry/RCC chamber with heavy-duty cover, backfilling, testing and measurement of earth resistance, complete in all respects as directed by the Engineer-in-Charge.

Dismantling and removal of existing LMO internal lighting arrangement including light fittings, connecting wires/cables, conduits, switches, junction boxes and accessories, electrical isolation, disconnection, collection and stacking of dismantled materials, complete as directed by Engineer-in-Charge