Establishment of 50 bedded

Amount

Ayush Hospital Building

Excavation in Soil with Dozer with lead upto 100 metres ( Excavation for road way in soil by mechanical means including cutting and pushing the earth to site of embankment upto a distance of 100 metres (average lead50 metres), including trimming bottom and side slopes in accordance with requirements of lines, grades and cross sections.)

Excavation in Ordinary Rock with Dozer with lead upto 100 metres (Excavation for roadway in ordinary rock by deploying a dozer, 80 HP including cutting and pushing the cut earth to site of embankment upto a distance of 100 metres ( average lead 50 metres ), trimming bottom and side slopes in accordance with the requirements of lines, grades and cross sections.)

Earth work in excavation in foundation and trenches etc. in all kinds of soil (excluding soil containing 50% or more of shingle or small size boulders upto 30 cm size, saturated soil and rock), lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers, when required, into plinth sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus soil as directed within a lead of 50m.

Dry Rubble Flooring

Providing and laying in foundations and plinth cement concrete 1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering.

Random rubble masonry with hard stone in foundations and plinth in cement mortar 1 : 6 (1 cement : 6 fine sand) including levelling up with cement concrete 1 : 6 : 12 (1 cement : 6 coarse sand : 12 stone shingle 20 mm nominal size) at plinth level.

Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcement in :a) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement.c) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement. b)1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in stair cases (excluding landing) except spiral cases including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface, preparing of the top surface and finishing, nosing upto floor two level but excluding the cost of centring, shuttering and reinforcement with 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone shingle 20 mm nominal size).

Centring and shuttering including strutting, propping etc and removal of form work for : a) Foundation, footings, bases of columns etc. and mass concrete.

b) Column, Pillars and Struts.

c) Lintels, beams, girders, bressumers and cantilevers etc.

d) Suspended floors, roofs, landings shelves and their supports balconies and chajjas (3.5m height).

e) Stairs (excluding landings) except spiral stair cases.

Reinforcement of RCC work including bending, binding and placing in position complete.a) Cold twisted bars.

Providing and laying damp proof course 38 mm thick with cement concrete 1 : 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate 12.5 mm nominal size).

Brick work with best available local bricks in foundations and plinth in cement mortar 1:6 (1 cement : 6 fine sand).

Brick work with best available local bricks in foundations and plinth in cement mortar 1:4 (1 cement : 4 fine sand).

Extra for brick work with best available local bricks in superstructure above plinth level up to floor two level.

Half brick masonry (with best available local bricks) in cement mortar 1:3 (1 cement : 3 coarse sand) in foundation and plinth.

Extra for brick work with best available local bricks in superstructure above plinth level up to floor two level.

Supplying and installing uPVC- Casement Door made out of Lead free green profile having "GREENLINE" mark of BIS standard uPVC sections of wall thickness 2.4mm, multi chambered with corners fusion , Single leaf Side hung Door using uPVC section of size 58mm x 69mm x 2.4mm thick wall for frame, 58mm x 109mm x 2.4mm thick wall for glass sash,Aluminium threshold at bottom. (ii) Using 5mm clear toughened glass

Double leaf Side hung Door with a Dummy Mullion - French Door using uPVC section of size 58mm x 69mm x 2.4mm thick wall for frame, 58mm x 109mm x 2.4mm thick wall for glass sash, 58mm x 61mm x 2.4mm thick wall for dummy mullion, Aluminium threshold at bottom.(i) Using 5mm clear glass

Supplying and installing uPVC- Sliding Windows made out of Lead free green profile having "GREENLINE" mark of BIS standard uPVC multi chambered sections of wall thickness 2.4mm with corners fusion , (ii) 4-Panel with 5mm clear float glass

Providing and fixing MS grills of required pattern in wooden frames of windows etc with MS flat, square or round bars with round headed bolts and nuts or by screws.b) ornamental Grill.

Providing & Fixing in position collapsible steel shutters with channel 20 x 10 x 2 mm and braced with flate iron diagonal 20 x 5 mm size top and bottom rail of T - iron 40 x 40 x 6 mm with 40 m m dia steel pulley complete with bolts, nuts ;ocking arrangment , stopper , handle etc complete

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes,channels, plates etc., including welding,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing MS fan clamp type I of 16 mm dia MS bar bent to shape with hooked ends in RCC slabs during lying including painting the exposed portion of loop all as per standard design complete.

Steel work in built up tubular trusses including cutting, hoisting, fixing in position including special shaped washers etc complete (welding to be paid separately).

Providing corrugated Dyna sheet roofing fixed with appropriate J or L hooks, bolts & nuts 8 mm dia with limpet washers etc as per the specification of the manufacturer complete, excluding the cost of purlins, rafters and trusses. a) 0.60 mm thick

Providing ridges or hips 60 cm overall in plain Dyna roof sheet fixed with J or L hooks, bolts and nuts 8 mm dia. limpet washers complete. a) 0.60 mm thick

Extra for providing and fixing wind ties of 40 x 6 mm flat iron section.

Providing and fixing 12 mm thick insulating board ceiling of approved quality with necessary nails etc. complete (frame work to be paid separately).

Applying water proofing coating black of ceiling tiles made of M/s Gypsum Ltd make for ceiling.

Excavation, collection and supplying of earth in ordinary soil carriage by mechanical transport i/c loading, unloading and banking of supplied earth in layers not exceedign 20 cm in depth brecking flods, watering ramming and dressing etc. complete.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

Providing and laying in foundations and plinth cement concrete 1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering.

Providing and laying in foundations and plinth cement concrete 1 : 3 :6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete

White glazed tiles 5mm.thick in flooring, skirting, risers of step and dado in 12 mm thick cement plaster 1 : 3 (1 cement: 3 coarse sand) painted with white cement slurry.

Chequered terrazzo tiles 22 mm thick with marble chips of sizes upto 6mm in floors on 25 mm thick bed mortar 1 : 3 (1 cement : 3 coarse sand) jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing complete: a) Light shades using white cement

12 mm cement plaster 1 : 3 (1 cement : 3 fine sand).

Applying two or more coats of JK or Birla or equivalent wall putty over cement mortar to give an even and smooth wall surface complete.

Finishing wall with textured exterior paint of required shade: New work ( two or more coats applied @ 3.28 Ltr/ 10 Sqm ) over and including base coat of water proofing cement paint applied @ 2.20 Kg/10 Sqm

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade on new work ( two or more coats )

Applying priming coat with ready mixed genuine red lead paint of approved brand and manufacture on steel work.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for steel work of approved brand and manufacture in all shades on new work to give an even shade.

Water Supply

Providing and fixing GI pipes complete with GI fittings and clamps including cutting and making good the walls (internal work). a) 15mm nominal bore.

b) 25mm nominal bore.

Providing and fixing GI pipes complete with GI fittings including trenching and refilling etc (external work). a) 50mm nominal bore.

Providing and fixing steel bib cock of approved quality.

Providing and fixing health fauset approved quality.

Providing and fixing water mixure approved quality.

Providing and fitting water gyeser of approved quality

Providing and fixing brass stop cock of approved quality. a) 15mm nominal bore.

b) 25mm nominal bore.

Providing and fixing aquaguard water treatment filter

Providing and fixing PVC connection pipe with brass union 30cm length.

Painting G.I. Pipes and fitting with white paint over a coat of ready mixed priming coat of approved quality for new work. a) 15mm dia pipe.

b) 20mm nominal bore.

c) 50mm dia pipe.

Providing Sintex water Tanks 5000 ltr Capacity

Providing and fixing white vitreous china type water closet pedestal (European type WC pan) with seat and lid CP brass hinges and rubber buffers, 12.5 Litres high level CI flushing cistern with fittings RS or CI brackets, galvanized steel telescopic flush pipe with fittings and clamps, 20 GI overflow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting making good the walls and floors where required.

Providing and fixing white vitreous china flat back or wall comer type lipped front urinal basin of 430x260x350 mm and 340x430x265 mm sizes respectively with Cl automatic flushing cistern with fittings, RS or Cl brackets standard size galvanized steel flush pipe and spreaders with brass unions and GI clamps complete including painting of cistern and fittings, cutting and making good the walls and floors where required.

Providing and fixing toilet paper holder.b) Polished wooden

Providing and fixing white vitreous china wash basin with RS or CI brackets painted white 15 mm CP brass pillar taps and CP brass chain with rubber plug 32 mm CP brass waste of standard pattern, 32 mm dia CP brass trap and MI unions complete, including cutting and making good the walls where required.(a) Flat back wash basin size 550x400 mm with a pair of 15 mm CP brass pillar taps of heavy quality.

Providing and fixing 600x450 mm bevelled edge mirror or superior glass (of approved quality) complete with 6 mm thick asbestos sheet ground fixed to wooden cleadt with CP brass screws and washers.

Providing and fixing 600 x 120 mm glass shelf with CP brass brackets and guard rail complete, fixed to wooden cleadts with CP brass screws.

Providing and fixing CP brass towel rail complete with CP brass brackets fixed to wooden cleadt with CP brass screws (heavy quality).a) 750 x 20 mm

Providing and fixing sand cast iron cast/iron (spun) soil, waste and vent pipes. a) 100 mm dia.

b) 75mm dia.

Providing and fixing sand cast iron heel rest sanitary bend. a) 100 mm dia.

b) 75mm dia.

Providing and fixing sand cast iron single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. a) 100 x 100 x 100 mm

b) 80 x 80 x 80 mm

Providing and fixing sand cast iron single equal plain junction of required degree a) 100 x 100 x 100 mm

b) 80 x 80 x 80 mm

Providing and fixing sand cast iron trap of self cleadnsing design with sand cast iron screwed down or hinged grating with or without vent arm complete including cost of cutting and making good the walls and floors. a) 100mm inlet and 100mm outlet.

b) 100mm inlet and 75mm outlet.

Providing and fixing kitchen sink including making all connection excluding cost of fittings.

Providing and fixing on wall face C.I. rain water pipe including filling the joints with spun yarn soaked in neat cement slurry and cement mortar 1 : 2 ( 1 cement : 2 fine sand). a)150 mm diameter pipe

Providing and fixing M.S. Holder bat clamps of approved design of C.I. or S.C.I. pipes embedded in and including cement concrete block 10 cm x 10 cm x 10 cm of 1 : 2 : 4 mix (1 cement : 2 coarse sand: 4 stone aggregate 20mm nominal size) including cost of cutting holes and making good the wall etc.a)150 mm diameter pipe

Providing and fixing on wall face C.I. accessories for rain water pipes including filling the joints with spun yarn soaked in neat cement slurry and cement mortar 1 : 2 ( 1 cement: 2 fine sand). (A) CI Plain bend a) 150 mm diameter

(B) CI Offset Plain a) 150 mm diameter

Making plinth protection with 2nd class bricks on edge in cement mortar 1 : 6 (1 cement : 6 fine sand) over 7.50 cm bed of dry bricks aggregate 40 mm nominal size rammed consolidated and grouted with fine sand and the top of bricks pointed with cement mortar 1 : 2 (1 cement : 2 fine sand).

Providing and fixing 25 mm dia GI pipe outlet in cement mortar 1 : 3 (1 cement :3 fine sand) including cutting and making good the wall.

Construction of cement concrete drain 15 cm wide and 15 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips or shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering and all exposed surfaces with 12 mm thick cement mortar 1 : 3 (1 cement : 3 coarse sand) including shuttering complete.

Providing laying and jointing glazed stone ware pipe grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete.a) 200 mm dia S W pipe

Providing and laying cement concrete 1 : 5 : 10 (1 cement : 5 lime sand : 10 graded stone aggregate 40 mm nominal size) all around SW Pipe including bed concrete 15 cm thick as per standard design. a) 200 mm dia S W pipe

Constructing brick masonry manhole with 2nd class bricks in cement mortar 1 : 5 (1 cement : 5 fine sand) RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone single 20 mm nominal size), foundation concrete 1 : 4 : 8 mix (1 cement : 4 coarse sand : 8 stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1 : 3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size) neatly finished complete as per standard design. a) Inside size 90 x 80 cm and 45 cm deep including CI cover with frame (light duty) 455 x 610 mm internal dimensions total weight of cover and frame to be not less than 38 Kg (weight of cover and frame to be not less than 38 kg, (weight of cover 23 Kg and weight of frame 15 Kg).

Making soak pit 2.50 m dia 3 m deep with 45 x 45 cm dry brick honeycomb shaft and SW drain pipe 100 mmdia 1.80 m long complete as per standard design.

Septic Tank

Earth work in excavation in foundation and trenches etc. in all kinds of soil (excluding soil containing 50% or more of shingle or small size boulders upto 30 cm size, saturated soil and rock), lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers, when required, into plinth sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus soil as directed within a lead of 50m.

Concrete 1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) excluding the cost of centering and shuttering.

Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcement in : a) 1 : 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size).

Reinforced cement concrete in walls (any thickness) including attached pillasters, buttresses, plinth and string course, fillets etc from top of foundation up to floor two level including finishing and plastering the exposed surfaces with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface excluding cost of centring, shuttering and reinforcement in : a) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).stone aggregate 20 mm nominal size)

Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforcement of RCC work including bending, binding and placing in position complete.a) Cold twisted bars

Centering and shuttering including strutting, propping etc. and removal of form work for: a) Suspended floors, roofs, landing shelve and theirsupports, balconies and chajjas (3.50m height)

b) Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

12 mm thick cement plaster 1:3( 1 cement : 3 fine sand)

Neat cement punning

Cement concrete flooring 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement. a) 40 mm thick.

Providing and fixing C.I manhole cover.

Internal Electrification

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sqmm 'Group "A"

'Group "B"

'Group "C"

Wiring for twin control light point with 1.5 sqmm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, 2 way Piano type switch, phenolic laminated sheet, suitable size M.S.box and earthing the point with 1.5 mm² FR PVC insulated copper conductor single core cable etc as required

Wiring for light / power plug with 2x4 sqmm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit alongwith 1 No 4 mm² FR PVC insulated copper conductor single core cable for loop earthing as required

Wiring for circuit /sub-main wiring alongwith earth wire with the following sizes a) 2 x 2.5 mm² + 1 x 2.5 mm² earth wire

b) 2 x 4.0 mm² + 1 x 4.0 mm² earth wire

c) 4 x 25.0 mm² + 2 x 16.0 mm² earth wire

Supplying and fixing of following sizes of PVC conduit along with accessories a) 32 mm

Supplying and fixing metal box of following sizes (nominal size) on surface a) 150 mm x 75 mm x 60 mm deep

b) 150 mm x 150 mm x 60 mm deep

Supplying and fixing following piano type switch/ socket on the existing switch box / cover including connections etc as required a) 5/6 Amp Switch

b) 3 pin 5/6 amp socket outlet

c) Telephone socket outlet

d) TV antenna socket outlet

e) Internet Outlet

Supplying and fixing of Ceiling rose on the existing junction box/wooden block including connection etc as required

Supplying and fixing of brass batten / angle holder including connection etc as required

Erectin of wall bracket / ceiling fittings of all sizes and shapes containing upto two GLS lamps per fitting, complete with all accessories including connection etc as required

Providing and fixing plain 16/0.20 mm twin twisted, flexible, FR PVC insulated,copper cable, in polythene sleeve, or conduit of suitable size on the floor/wall,or side of the table / door etc as required

Providing and fixing plain 16/0.20 mm twin, FR PVC insulated, PVC sheathed,flat flexible copper cable on the floor / wall, or side of the table / door etc as required

Installation, testing and commissioning of pre-wired, fluorescent fitting of all types, complete with all accessories and tube etc directly on ceiling / wall,including connection with 1.5 mm² FR PVC insulated, copper conductor,single core cable and earthing etc as required

Installation of exhaust fan upto 450 mm sweep in the existing opening, including making the hole to suit the size of the above fan, making good the damage, connection, testing, commissioning etc.as required

Extra for fixing the louvers / shutters complete with frame for a exhaust fan of all sizes

Supplying of 4'-40 watt Decorative single box type tube fitting with all accessories as required

Supplying of 2' - 20 watt Single Box type flourescent tube fitting complete as required

Supplying of exhaust fan of 300/380 mm sweep

Supplying of ceiling fan fan of 1200 mm sweep

Supplying and fixing of Ding Dong call bell and bell push suitable for 230 V AC supply with all accessories etc. as required.

Supplying & fixing of 4'-40' watt flourescent tube.

Supplying & fixing of 100/60 watt incandescent lamp.

Providing 15A, five in one switch socket combined.

Supplying and fixing of decorative garden light fitting complete

Supplying of Bakelite round sheet 4" diameter

Supplying of PVC flexible pipe of 1" diameter

Suppying of 18 SWG PVC insulated Copper earthing wire

Supplying of Al. Thimble of following sizes :- a) 35 sqmm

b) 95 sqmm

Drill Bit of size 1/2"

Supplying of Machine Screw of sizes:- a) 1x1/2"

Supplying of Machine Screw with Nut of size 2" length

Supplying of white coloured brass washer

Supplying of Nuts & Bolts of 1" length

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. a) Upto 35 sq. mm

b) Above 185 sq. mm and upto 400 sq. mm

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required. a) Above 185 sq. mm and upto 400 sq. mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 240 sq. mm (62mm)

Supplying, installation, testing and Commission of the following outdoor Luminaries complete with all accessories such as ballast, starter, driver etc. including connection cable, as approved by the Deptt. including connections etc. as required and directed by the department.

Supply of following size PVC/XLPE insulated and PVC sheathed 1.1 KV G Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908 (Part 1) 1988 armoured U.G. cable as specified and directed by the deptt. a). 4.00 Sq.mm 3 Core Aluminium armoured U.G. cable

b). 6.00 Sq.mm 3 Core Aluminium armoured U.G. cable

c). 25.00 Sq. mm 3 & 1/2 Core Aluminium armoured U.G. cable

Supplying including installation of the Octagonal poles shall be designed to withstand the maximum wind speed of 169 km/hr. The top loading i.e. area and weight of fixtures are to be considered to calculate maximum deflection of the poles and the same shall meet the requirement of BS:5649 Part VI 1982. The pole shaft shall have octagonal cross section and shall be continuously tapered with single longitudinal welding. There shall not be any circumferential welding of the pole shaft. The welding of the pole shaft shall be done by Submerged Welding process. All octagonal pole shafts shall be provided with the rigid flange plate of suitable thickness with provision for fixing 4 foundation bolts. The base plate shall be fillet welded to the pole shaft at two locations i.e. from inside and outside. The welding shall be done as per process approved by Third Party Inspection agency. (BAJAJ/ PHILIPS/ VALMONT/ PARUTHI ENGR/Nezone make)

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Extra for using salt and coke for GI or copper plate earth electrode as required

Supplying and laying 25mm x 5mm G.I.strip at 0.5 metre below ground as strip earth electrode, including soldering etc. as required

Providing and fixing 25mm x 5mm G.I.strip in 40mm dia G.I. pipe from earth electrode, as required

Providing and fixing 25mm x 5mm G.I. strip on surface or in recess for connections etc as required

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required

Supplying & fixing of lightning conductor on the roof of the building

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing alongwith existing surface / recessed conduit / submain wiring / cable as required

Providing and fixing 25mm x 5mm copper strip on surface or in recess for connections etc as required

Procurement Installation and commissioning of 500 KVA,11/0.415 KV Distribution sub station

C/O LTOH line with 7.5 mm steel tubler pole and 6/1/2.11 sqmm ACSR Conductor

Load Security to be paid to Local Power Supply and other necessary expenses

Supplying including installation, testing and commissioning of Water Cooled 3-phase, 415 volt, 1500 RPM, 50 HZ, Diesel generator set of 125 KVA Diesel Generator set coupled to suitable alternator of 220/415 V, AC, 1/3-Phase 0.8 p.f. complete with all accessories as specified and directed by the department conforming to IS.

Parking Area

Preparation of sub grade (Preparation of sub grade by excavating earth to an average depth of 22.50 cm, dressing to camber and consolidating with road roller, making good the undulations etc. and disposal of surplus earth, lead upto 50 m.)

Consolidation of sub-grade with road roller of 8 to 12 tonne capacity including making good the undulations etc. with earth or quarry spoils etc. and rerolling the sub grade.

Granular Sub-Base with Coarse Graded Material ( Table:- 400- 2) (Construction of granular sub-base by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401) (iii) for grading-III Material

Dry Lean Cement Concrete Sub- base (Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonnes vibratory roller, finishing and and curing.

Cement Concrete Pavement (Construction of un-reinforced, dowel jointed,plain cement concrete pavement over a prepared sub base with 43 grade cement @ 400 kg per cum, coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site,laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane,sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per drawing

Chequered terrazzo tiles 22 mm thick with marble chips of sizes upto 6mm in floors on 25 mm thick bed mortar 1 : 3 (1 cement : 3 coarse sand) jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing complete:

Box Culvert

Earth work in excavation in foundation in saturated soil including pumping or bailing out of water and disposing of excavated earth within a lead up to 50 m lift up to 1.50 m

Providing and laying Dry stone soling i/c packing with smaller stones

Providing and laying in foundations and plinth cement concrete 1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Reinforced cement concrete in walls (any thickness) including attached pilasters, buttresses,plinth and string course, fillets etc from top of foundation up to floor two level including finishing and plastering the exposed surfaces with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface excluding cost of centring,a) M20 (1 cement : 1.5 corase sand : 3 stone aggregate 20 mm nominal size)

Reinforced cement concrete work in suspended floor,roof,landing up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement.a) M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Centring and shuttering including strutting, propping etc and removal of formwork for :b) Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

d) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).

12 mm cement plaster 1 : 3 (1 cement : 3 fine sand).

Back filling behind abutment, wing wall and return wall complete as per drawing and Technical specification

Boundary Wall

Earth work in excavation in foundation and trenches or drains not exceeding 1.5 m in width or 10 Sqm on plan including dressing of sides and ramming of bottoms lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soils as directed,within a lead of 50 m

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:4:8 (1 Cement :4 fine sand : 8 graded stone aggregate 40mm nominal size)

Reinforcement for RCC work including straightening,cutting,bending,placing in position and binding all complete. b) Cold twisted bars.

Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcement in :a) M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement.1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams,suspended floors, roofs having slope up to 15 degree landing,balconies,shelves,chajjas,lintels,bands,plain window sills,staircases and spiral stair cases upto floor five level excluding the cost of centering,shuttering,finishing and reinforcement with 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Centering and shuttering including strutting, propping etc and removal of form work for : a).Foundation, footings, bases of columns etc. and mass concrete.

b).Column, pillars, piers,abutment,posts and struts

c). Lintels, beams, girders, bressumers and cantilevers etc.

Half brick masonry (with best available local bricks) in cement mortar 1:3 (1 cement : 3 coarse sand) in foundation and plinth.

Extra for brick work with best available local bricks in superstructure above plinth level up to floor two level.

12 mm cement plaster of mix 1 : 3 (1 cement : 3 fine sand).

Applying two or more coats of JK or Birla or equivalent wall putty over cement mortar to give an even and smooth wall surface complete.

Providing and fixing 90 mtr. Height barbed wire fencing with 90 m. long MS angle iron post 50 x 50 x 6 mm size of standard design placed every 3.00 m with GI wire and staining bolts including cost of making holes to the angle iron posts.

Finishing walls with water proofing cement paint of approved brand and manufacture. Quantity same as item 11

Main Gate

Earth work in excavation in foundation and trenches or drains not exceeding 1.5 m in width or 10 Sqm on plan including dressing of sides and ramming of bottoms lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soils as directed,within a lead of 50 m

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:4:8 (1 Cement :4 fine sand : 8 graded stone aggregate 40mm nominal size)

Reinforcement for RCC work including straightening,cutting,bending,placing in position and binding all complete. b) Cold twisted bars.

Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcement in :1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement.1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams,suspended floors, roofs shelves,chajjas,lintels,bands,plain window sills,staircases and spiral stair cases upto floor five level excluding the cost of centering,shuttering,finishing and reinforcement with 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Centering and shuttering including strutting, propping etc and removal of form work for : a) Foundation, footings, bases of columns etc. and mass concrete.

b) Column, pillars, piers,abutment,posts and struts

c) Lintels, beams, girders, bressumers and cantilevers etc.

12 mm cement plaster of mix 1 : 3 (1 cement 1 : 3 fine sand).

Finishing walls with water proofing cement paint of approved brand and manufacture and required shade on new work (three or more coats) to give an even shade.suitable shade

Providing and fixing 1 no. of MS Gate

Drainage System

Earth work in excavation in foundation in saturated soil including pumping or bailing out of water and disposing of excavated earth within a lead up to 50 m lift up to 1.50 m

Providing and laying Dry stone soling i/c packing with smaller stones

Providing and laying cement concrete 1 : 4 : 8 (1 cement : 4 sand : 8 stone shingles 40 mm nominal size in foundation and plinth

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Reinforced cement concrete in walls (any thickness) including attached pilasters, buttresses,plinth and string course, fillets etc from top of foundation up to floor two level including finishing and plastering the exposed surfaces with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface excluding cost of centring,a) M20 (1 cement : 1.5 corase sand : 3 stone aggregate 20 mm nominal size)

Reinforced cement concrete work in suspended floor,roof,landing up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement.a) M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Centring and shuttering including strutting, propping etc and removal of formwork for :a) Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

b) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).

12 mm cement plaster 1 : 3 (1 cement : 3 fine sand).

Neat Cement punning

Installation of fire fighting system

Automatic fire alarm system

Furnishing Items :- a). Sofa set (3+1+1 seated)

b). 'Ikey' 12 Feet Reception desk with marble front

c). Nilkamal Recardo Office Table (New Wenge)

d). Nilkamal Elegant Executive Office Table (Walnut)

e). Executive Table 6'

f) Juari Chair Executive

g) Hayao Computer Table in Wenge Finish, By Mintwud from Pepperfry

h) Timber Cheese Ergonomic Office Chair (2 Years Of Warranty, New Launch, Zeenion (Backrest With Cushion)Bright Black, Mixture Of Metal And Wood)

i) Nilkamal Signature Fabric Arm Chair

j). Lenevo all in one PC

k). Lenovo UPS

l) Canon LaserShot LBP 2900B Monochrome Laser Printer (Black/Grey)

m). Water filter hot and cool

n). Sony bravia KD-43X74 43 Inch LED 4K, 3840 X 2160 Pixels TV

o). Sony KD-32W830 32 Inch LED HD Ready, 1366 X 768 TV

p). Window Curtains

q). Refrigeretor 160 ltrs

M/s Tenzin Enterprises