SPECIAL REPAIR IN OTM BUILDING NUMBER P-8A (COOK HOUSE CUM DINING HALL) OF 199 MED REGT AT ZONE-I AREA UNDER JAIPUR MILITARY STN

Amount

M&L for Demolition of PCC in ground floors and pavings n exc 15 cm thickness (below ground level) rubbish off the premises complete all as directed

Demolition of brick work or stone boulder masonry built in cement mortar rubbish off the premises complete all as directed

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. rubbish off the premises.

M&L for Brickwork with sub class `B' bricks (old size), straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all as directed

M & L for stone Walling of Squared rubble masonry, regular coursed, well bonded, bedded and solidly hearted built in CM 1:4 complete all as directed

M&L for rendering 10 mm thick cement plaster in CM 1:6 on stone masonary or other faces of brick work including finished even and smooth without using extra cement complete all as directed

M&L for rendering 15 mm in CM 1:4 on fair faces on brick or concrete surface including finished even and smooth without using extra cement complete all as directed

M&L for rendering 15 mm thick in CM 1:4 on stone masonry surface or surface other than fair faces of brick works including finished even and smooth without using extra cement.

M&L preparation of newly plastered surface wall and applying two coats of oil bound distemper of any tint over a coat of chalk whitening primer complete all as specified and directed.

M&L preparation of old plastered surface wall and applying two coats of dry distemper of any tint over a coat of chalk whitening primer complete all as specified and directed.

M&L preparation of newly plastered surface wall and applying two coats of cement base paint of any tint over a coat of primer complete all as specified and directed.

M&L preparation of old plastered surface wall and applying two coats of cement base paint of any tint over a coat of primer complete all as specified and directed.

M&L preparing new steel surfaces of any description exc 10 cm width or grith and applying two coats of synthetic enamel paint over a coat of red oxide zink chrome.

M&L preparing old steel surfaces of any description exc 10 cm width or grith and applying two coats of synthetic enamel paint .

M&L preparing new wooden surfaces of any description exc 10 cm width or grith and applying two coats of synthetic enamel paint over a coat of pink primer

M&L preparing old wooden surfaces of any description exc 10 cm width or grith and applying two coats of synthetic enamel paint .

Dismentling of floor hearth or wall tiling incl cement mortar bedding (but not backing) and rubbish off the premises.

M&L Non skid coloured joint free ceramic tiles 9mm to 9.50mm thick (Square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm as in floor set and jointed in neat cement slurry and pointed in coloured cement match the shade of tiles laid over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L coloured glazed ceramic tiles (450x300x7)mm thick, on vertical surfaces of wall such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles laid over and including 10 mm thick backing coat in CM 1:4 complete all as specified and directed.

Dismantling of bedded Stone slabs and tiles of any description or thickness in floors, aprons etc rubbish off the premises.

M&L for 20-25 mm thick Machine cut kota stone slab flooring over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations

M & L for chequered cement concrete tiles 25cmx25cm x20mm thick with grey cement and pigment in floors etc set jointed and pointed in neat cement slurry over and incl 15mm thick screed in CM (1:6) all as approved and directed

M&L for cement concrete in sub base and mass filling 1:4:8 type D-2 using 40 mm graded stone aggregates

M&L cement concrete in mass filling 1:2:4 type B-2 using 20 mm graded stone aggregates

Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings

M & L for Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M & L for Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof overing/ cladding to wall, fixed with self tapping screws as specified

M & L Rolled Mild steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, minimum Gde E-165 (Fe-290) complete all as directed.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as directed.

M&L for 600x600 mm tile/board laminated inner surface and core Gypsum Board 8-10mm thick in ceiling fixed with screw complete all as specified and directed.

S& F galvenised metal snap grid matrix frame work for false ceiling 25 mm main TEE and cross TEE with all connected fixtures and fittings as specified size of frame 605x605mm including hanging wires GI adjusting level fixed to roof girder / rafters / purlins/ truss by means of ceiling cleats as required complete all as directed.

Taking down door chowkaht or frame of any description area exc 1.50 Sqm n exc 4 sqm each without taking off shutters from the frame.

Taking down door chowkaht or frame of any description area n exc 1.50 Sqm each without taking off shutters from the frame.

S & F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded

S & F Steel ventilator with top hung shutter including hinges, steel peg stay, complete

S & F Steel windows or ventilators, fixed type, with glazing bars

S&F in repair stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm fixed with stainless steel wire staples.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm fixed with stainless steel wire staples.

S&F sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane with 3 mm thickness

S&F Butt hinges, medium weight , cold rolled mild steel, and fixed 100 mm

S&F 200 mm long Aluminium anodised barrel tower bolt of extruded section

S&F aluminium handles cast type anodised 150 mm size complete all as specified

S&F Door closer aluminium anodized extrudedsection body hydraulically regulated designation No-3 universal type suitable for door shutter of 851 to 1000mm in width and of weight between 61 to 80 Kg.

M&L for rolled mild steel framed work as in door frame of angle or other section and fixed with angle cleats and connecting plates etc of Gde E-165 (Fe-290) Note:- Cost of welding butt hinges to the door frame deemed to included in quoted rate

S & F 35mm thick factory made plain, framed, paneled door shutters kiln seasoned and chemically pressure treated second class, hardwood (two panels) with lock rail and panel of 9mm thick BWP commercial marine grade ply wood bonded with high quality liquid phenol formal dehyde synthetic resin adhesive confirming to IS-710. The size of rails and style shall be as per IS-1003.

S & F 35mm thick factory made second class hardwood glazed and skelton door shutter kiln seasoned and chemically treated, open rebated and prepared to receive glass/ gauge etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc complete. The size of members of shutters shall be as specified in MES SSR Part-I.

S & F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube of 1.25 mm thickness suppling & fixing in opening as per specification & drawing.

S&F Factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

Supply and fixing anodised aluminium frame for door , windows, ventilators with one or more rebates incl jointing cleat for fixing etc complete all as specified

Supply and fixing anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc complete

M&L for 09 mm thick prelaminated particle board interior grade, prelaminated both side with decorative choice lamination fixed with screw .

S&F sheet glass 4.00 mm thick, ordinary quality and glazing with oil putty in square exc 0.5 sqm in each pane fixed with rubber packing etc complete all as directed.

S & F brass mortice lock verticle type size 65mm, 4 levers with escutcheon plates and two keys fixed in aluminium frame.

M&L for double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover governing pivot made of brass other parts made of mild steel heavy duty and fixed

Taking up or down steel tubing and connection including cleaning 15 mm bore

Taking up or down steel tubing and connection including cleaning 20 mm bore

Taking up or down steel tubing and connection including cleaning 25 mm bore

S&F GI tubing medium grade with all fitting 15 mm bore fixed to wall or concealed or fitted to ceiling or laid under floor.

S&F GI tubing medium grade with all fitting 20 mm bore fixed to wall or concealed or fitted to ceiling or laid under floor.

S&F GI tubing medium grade with all fitting 25 mm bore fixed to wall or concealed or fitted to ceiling or laid under floor.

S&F 15 mm bore bib tap fancy type chromium plated cast copper alloy with cruth or butter fly handle screwed down for iron pipeand fixed complete.

S&F in repairs PVC valveless,syphonic action type flushing cistern low level 10 ltr capacity white, with intel, ball valve, float and handle including brakects flushing, brakects flushing pipe complete all as specified & directed.

S&F PVC connections 15 mm size with PTMT nuts of length 600 mm.

S&F in repairs Vitreous China wash basin, white , flat back, size 550mmx 400mm but including brackets , coupling and waste pipe complete

S&F in repair Pillar tap, 15mm bore cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe.

S&F in repair stainless steel grating doom 100 mm dia all as directed

S&F in repair vitreous china Squatting pan 'Orissa' pattern water closet white size 580mm x 440 mm with integral foot rest (excluding flushing cistern and flush pipe) complete including connection to trap and flushing pipe antisyphone pipe etc.

S&F in repair vitreous China urinals, bowl type (back or corner wall type) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement

S&F in repair stop valve cast copper alloy, screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe 20 mm bore or union and fixed

S&F in repair stop valve cast copper alloy, screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe 15 mm bore or union and fixed

S&F in repair angle stop valve 15mm bore cast copper alloy chromium plated screwed for iron pipe.

S&F in repair ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic bal screwed for iron pipe 20 mm dia and fixed (Minimum Weight 210 gms)

S&F in repair PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors 75 mm bore

S&F in repair PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors 110 mm bore

S&F in repair PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls 110mm

PVC (SWR) bends any radius 75 mm bore

PVC (SWR) bends any radius 110 mm bore

M & L PVC (SWR) floor trap,75mm bore, plain with grating including jointing with solvent cement.

PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement

Disconnecting existing tank of capacity exc 500 and not exc 1000 litre,setting aside for repairs, cleaning etc and hoisting if required, reconnecting and refixing in position .

S&F Rotatinal moulded, tripple layered, polyethylene water storage tanks (Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I capacity 1000 ltr

S&F Rotatinal moulded, tripple layered, polyethylene water storage tanks (Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I capacity 500 ltr

S&F sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 10mm x 330mm x 160mm

M&L 50 mm thick plain cement concrete type C-1 1:3:6 (Using 20 mm graded stone aggergates ) as in plinth protections finished even and fair with joints 10 mm wide and in full depth at corners and @ 3 m c/c filled with mastic mortar.

S & F in repair Providing precast cement concrete louvres and jallies, 25mm thick (measured solid), including all mould- ings but excluding frame Type B0 1:2:4 (12.5 mm) aggregate

S & F in repair stainless steel kitchen plate rack of overall minimum size 900 x 750 x 225mm with partitions for small/ large plates etc made out of stainless steel 24 gauge, fixed with rawl plug and CP steel screws all as directed of approved quality

M&L for plain cement concrete type B1 1:2:4 ( 20mm graded aggregate) as in lintels, cills steps, seismic and other similar bands , copings, kneelers, apex stone bed plates , kerb ,water troughs and like including weathering, slightly rounded or chamfered angles and throating as directed.

M & L for Machine pressed precast concrete rubber moulded interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade, with grey cement laid over & including 25mm thick sand cushion layer complete all as specified and directed.

M & L for precast PCC blocks or slabs 150 mm thick (1:2:4) mix type B-1 using 20 mm graded aggregated with plain or interlocking joints, Kerb stone on road side etc as directed complete in walls setting in CM (1:6) complete all as directed.

M&L for preparation of new concrete surfaces of any description over 10cm girth or width, not otherwise described and applying two coat of synthetic enamel paint over a coat of primer complete all as specified

Dismantling wrought iron or mild steel work of any description nototherwise provided for

Demolition of RCC in ground floors and pavings n exc 15 cm thickness( below ground level)

M&L precast reinforced cement concrete slab type B1, 1:2:4 ( 20mm graded aggregate ) as in landing, drain cover slab (for manholes etc) , chajjas , drain cover and shelves and similar articles with plain faces .(Reinforcement shall be measured & paid separatel.)

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking , bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

All as per item No 96 above but 6mm to 8mm dia

S&F mild steel frame of angle section or MS flat with all requires welding and joints for the in situ casting in RCC drain covers or other purpose of size as per direction at site complete all as specified.

Taking down carefully surface aluminum or copper point wiring with exisitng PVC concealed conduit for (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling rose, regulators, sockets, light fittings etc and making good disturbed surfaces complete.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 1.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) drawn into & including concealed rigid non metalic PVC conduit medium grade not less than 20mm dia ISI marked ivory colour with all conduit fittings and terminated in and unwelded sunken galvanised pressed steel terminal boxes of thickness not less than 1.0 mm covered with 3 mm thick phenoic laminated white sheet cover for mounting switches, sockets, fan regulators as required for one light point controlled by one switch.

All as per item No. 100 here-in-before but one fan point controlled by one switch.

All as per item No. 100 here-in-before but one socket outlet 6 amp controlled by one switch on the same board with other switches.

All as per item No. 100 here-in-before but one socket outlet 6 amp controlled by one switch on indepdendent board.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 4.0 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 4.0 sqmm (Green) drawn into into & including concealed rigid non metalic PVC conduit medium grade not less than 20mm dia ISI marked ivory colour with all conduit and terminated in and unwelded sunken galvanised pressed steel terminal boxes of thickness not less than 1.0 mm covered with 3 mm thick phenoic laminated white sheet cover one socket point 16 Amps controlled by one switch.

S&F switch piano flush button single pole one way 6 Amp complete.

S&F switch piano flush button single pole one way 16 Amp complete.

S&F socket outlet, 2-in-1, 3 pin 6 & 16 Amps flush type compete.

S&F socket outlet, 2-in-1, 3 pin 6 Amps flush type compete.

S&F hum free electronic step fan regulator 120-280 volts of 100 watts capacity (socket type) including connecting up complete.

S&F ceiling rose 3 plates polycarbonate body complete.

Taking down carefully sub main wiring form casing capping/PVC surface conduit and making good disturbed surfaces complete all as directed.

M&L for submain wiring with two runs of single core PVC insulated and unsheathed, multistranded FRLS copper conductor of size 6.00 sqmm, LT cable, 1100 volts grade and one run of 6 sqmm single core, multistrand copper conductor (green) as earth continuity conductor drawn into existing conduit complete all as specified and directed. NOTE: Two runs of 6 sqmm cable, one run of 6 sqmm cable shall be measured as one running metre of submain wiring.

S&F in repair LED batten (1.2M) made of CRCA sheet housing with a PC glossy diffuser duly prewired connection having a nominal system lumen output of 2000 lumens at a minimum system efficacy of 115 lumen per watt and total power consumption not more than 20 watt including driver. It has a rated system life time of 40000 burning hours at L70 and should have a color temperature of 6500K, CRI>80, THD<10% and PF>0.95 complete. Make - Philips cat ref no. ENDURALED BATTEN "BN 108C LED 20S PSU CDL WH" or Bajaj cat ref no. BLTRU 20W WH VIVA or equivalent in other specified make as approved.

M&L for earthing with galvanized steel earth plate electrode 600mmx600mmx6mm thick buried directly in ground (earth pit not less than 2.25 meter deep below normal ground level) with the top edge of the plate not less than 1.5m below normal ground level connected to galvanized earth lead wire 4mm dia by means of steel bolts, nuts, check nuts and washers all as shown in electrical plate No. 03 of SSR Part -I connected to earthing point and including 15mm bore light grade G.I. protection pipe (upto 7.5 mtr from edge of the pit), PCC pit in mix 1:3:6 type C1 with PCC 1:2:4 type B-1, 40mm thick cover, watering arrangement with funnel and wire mesh and 20mm bore light grade G.I. watering pipe, common salt and charcoal filling, necessary excavation and earh work including testing on completion.

Taking down MCB distribution boards with incoming and outgoing controls any make any capacity after disconnecting complete.

S&F MCB distribution board, powder coated, CRCA steel sheet, degree of protection IP 43, IK-09 with reversible double door, recess mounted , having insulated 100 Amps tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required with SPN, 240 volts, 8 ways.

S&F MCB distribution board, single pole and neutral, powder coated CRCA steel sheet, suitable for 8 way 415 volts, degree of protection IP 43, IK-09 with reversible double door, recess mounted, having 100 Amps insulated tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required.

S&F in repair MCBs of 'C' series single pole 6 to 32 Amps having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs complete.

S&F in repair MCBs of 'C' series SPN 40 to 63 Amps having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs complete.

Supply and fixing 415V 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the DB complete with connection testing and commissioning for TPN 40 to 100 Apm complete all as directed.

S & F LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size

S&F exhaust fan, 300mm sweep, made of sturdy engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, coper winding complete all as directed.

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated completed with all accessories such as safety valve, themostate, NRV connection piece etc.

Sand cushioning to cable with dry fine sand in trenchs 8 cm below the cable and 15 cm above the cable after laying complete.

Bricks laid in trenches flat with width equal to length of brick for cable protection well burnt sub class 'B' laid across the cable complete

Dismantling and taking out UG cable any size unserviceable items fixed in any position and removal from site, all as directed.

S&F 1100 volt grade heavy duty XLPE cable with PVC insulated aluminum conductor served with inner sheathing of PVC tape armoured with galvanized steel strip or wire and overall PVC sheathed of size 25 Sqmm nominal cross section 4.0 core laid in trenches,fixed to pole or passing through pipes including all necessary clamps,nuts, bolts washers complete all as specified and directed.

Taking down fan, sealing cable end, dismantling blades and removing fan and blades to store and hanging again after all repair and rewinding including cable for making connection etc complete all as directed.

Rewinding the motor of celing fan 1200/1400 mm of any type and make with super enamelled copper wire of existing gauge of approved quality including overhauling and minor repairs for satisfactory operation, testing for the original speed & consumption

Renewal of ball bearing of ceiling / exhaust fan of any size and make as required with alignment of shaft and testing complete.

Renewal of AC film capacitor 2.5 mfd, 440 volts suitable for any type ceiling fan in FR plastic casing including connection complete.

Renewal of shaft of approved quality for ceiling fan / exhaust fan any make any type & size as required.

M&L for painting of ceiling fan of any sweep and make with one or more coats of spray painting with best quality enamel paint of required colour and approved brand to give an even shade and polishing with rubbing compound and wax polish including cleaning of surface with detergent etc

Renewal of rubber reel with a pair of clamp, nuts, bolts, split pins etc suitable for ceiling fan down rods of any size and make as required.

Renewal of PVC canopy suitable for ceiling fan of any size and make as required.

Excavation in trenches not exceeding 1.5 m wide and n.exc. 1.5 m deep for foundation of poles/ stay/ cable etc including getting out in any type of soil complete all as specified and directed

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm in hard and dense soil

Removing excavated material n.exc. 50m and depositing where directed at a level n.exc. 1.5 m above the starting point.

Schedule of Credit

MSR INFRATECH

JAGDAMBA CONSTRUCTION COMPANY

M/S JALANDRA CONSTRUCTIONS

Shiv Construction Company

SAI MAX INFRAPROJECTS