Development of additional Tourist Infrastructure facilities at Poompuhar, Mayiladuthurai District, Tamil Nadu.

Earth work excavation for foundation by Mechanical means for Isolated & Combined Footing etc in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 100 mts and clearing and levelling including dressing of sides and raming of bottoms etc., complete complying with standard specification and as directed by the departmental officers.- Upto 2.40m Footing Depth.

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Installation of Vertical Bored cast in situ RCC piles in all types of soils, using Standardised Concrete Mix M40 grade, with sulphate resistant Cement, fine aggregate, 20mm and down graded HBGS jelly coares aggregate. The rate includes cost of reinforcing steel, binding wire, fabrication, welding charges, placing of reinforcement cage in bore hole in correct position, cost of boring to the required depth with Bentonite solution with temprory casing of required length, conveyance of RMC to site and pouring concrete using Tremine pipes, conveyance of all materials to the site including all tools and plants, shifting the plants and equipments from one point to another, excavtion of mud pits for circulation of Bentonite soultion, closing the mud pits to original level and mud removal with initial lead and lift but including dismanteling the concrete above the cut off level etc complete as directed by the departmental officers including socketing. The reinforcement cage should be welded properly for lifting. The concrete cubes to be tested as per IS 456-2000. Acceptance criteria by clause 16.1. Frequency of testing as per 15.2.2. Testing to be conducted at both the ends at site as well as RMC plant. Pile driving depth should be decided by the departmental officers at site. The length of pile for payment shall be measured from top of shoe to the bottom of the pile cap. a)600 mm dia pile having longitudinal main reinforcement of 12 Nos. of 16mm dia rods with helical reinforcement at 8mm dia at 150mm c/c with inner rings of 12mm dia @ 1000mm c/c with lifting hook of 12mm dia at required length

Cement Concrete 1:5:10 (One Cement, Five sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Supplying and filling in foundation, basement, etc with filling sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification

Supplying and filling GRAVEL in 'foundation and basement with filling sand in layers of not more than 15cm.thick well rammed watered and compacted -1m3 etc., complete complying with standard specification.

Cement Concrete 1:5:10 (One cement, Five sand and Ten hard broken stone) using 40 mm gauge hard broken jelly for flooring including laying, consolidating, finishing, rendering the top surface rough to receive the floor, curing, etc. complete complying with standard specification

Brick work in Cement Mortar 1:3 using best quality Fly ash Brick of size 230x110x75mm with class designation of 7.5 conforming to IS 13757-1993 or IS 12894-2002 for foundation and basement including Cost of Mortar Plasticizer, curing, etc., complete complying with standard specification and as directed by the departmental officers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally.other type of bond shall be done etc. complete complying with standard specification A)For foundation & basement

Brick work in Cement Mortar 1:5 using best quality Fly ash Brick of size 230x110x75mm with class designation of 7.5 conforming to IS 13757-1993 or IS 12894-2002 for foundation and basement including Cost of Mortar Plasticizer, curing, etc., complete complying with standard specification and as directed by the departmental officers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally.other type of bond shall be done etc. complete complying with standard specification A)For foundation & basement

Brick work in Cement Mortar 1:6 using best quality Fly ash Brick of size 230x110x75mm with class designation of 7.5 conforming to IS 13757-1993 or IS 12894-2002 for foundation and basement including Cost of Mortar Plasticizer, curing, etc., complete complying with standard specification and as directed by the departmental officers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally.other type of bond shall be done etc. complete complying with standard specification

In Ground floor

In First floor

In Second floor

Brick partition walls of 11.50cm thickness using best quality II class Ground moulded chamber burnt bricks of size 9" x 4-3/8" x 2-3/4" in Cement Mortar 1:3 (One Cement and Three Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers.

In Ground Floor

In First Floor

Damp proof course with Cement Mortar 1:4 (One Cement and Four sand) 12mm thick mixed with best approved quality water proofing compound conforming to Indian Standard specification as specified by the departmental officers at 2% by weight of cement used, finishing and curing etc. complete complying with standard specification.

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, Sill slabs etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid with silver oak joists of size 10cm x 5cm & 7.5cm x 5cm as support runner , vertical stiffener, side support and Top Horizontal stiffener spaced at about 60cm to 90cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid).

Supplying and erecting centering for plane surfaces such as RCC Floor/Roof Beam, Lintels, Cantilever Beams, Bed Blocks etc.. with necessary supports and strutting upto 3.60m height in all floors with all cross bracings using MS Sheets made of 10 gauge thick welded with MS angle of Size 25mm x 25mm x 3mm for boarding laid over Steel adjustable Span of Size 2m x 2m(expandable upto 3.60m) and Silver Oak Joists of Size 10 x 5 cm spaced at 50cm to 60cm c/c and supported by Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick) Spaced at not more than 50 to 60cm c/c , etc complete complying with standard specifications. Steel adjustable span and Steel Adjustable telescopic props shall be provided as directed by the departmental Officers. (Payment for centering shall be given after the concrete is laid).

Supplying and erecting centering for plane surfaces such as RCC Floor/Roof Beam, Lintels, Cantilever Beams, Bed Blocks etc upto 3.60m height

Centering for curved RCC Beam surfaces above 3.60m upto 4.90m height

Supplying and erecting centering for plane surfaces such as RCC Floor Slab, Roof Slab, Loft, Landing Slabs, etc with necessary supports and strutting upto 3.60m height in all floors with all cross bracings using MS Sheets made of 10 gauge thick welded with MS angle of Size 25mm x 25mm x 3mm for boarding laid over steel adjustable span of size 2m x 2m (expandable upto 3.60m) and supported by Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick) , etc complete complying with standard specifications. Steel adjustable span and Steel Adjustable telescopic props shall be provided as directed by the departmental Officers. (Payment for centering shall be given after the concrete is laid). a)Centering for RCC slab surfaces upto 3.60m height

Supplying and erecting centering for plane surfaces such as RCC Floor Slab, Roof Slab, Loft, Landing Slabs, etc with necessary supports and strutting above 3.60m upto 4.90m height in all floors with all cross bracings using MS Sheets made of 10 gauge thick welded with MS angle of Size 25mm x 25mm x 3mm for boarding laid over steel adjustable span of size 2m x 2m (expandable upto 3.60m) and supported by Steel Adjustable Telescopic Props of Size 2.40m x 3.00m (expandable upto 4.90m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick) with Cross bracings provided at two levels at a spacing of 1.80m ,etc complete complying with standard specifications. Steel adjustable span and Steel Adjustable telescopic props shall be provided as directed by the departmental Officers (Payment for centering shall be given after the concrete is laid). a)Centering for RCC slab surfaces above 3.60m upto 4.90m height

Supplying and erecting steel centering including necessary supports For plane surfaces such as rectangular or square RCC columns etc. which require only nominal strutting using mild steel sheets made of 10 gauge thick welded with MS angle size 40mm x 40mm x 5 mm and supported by Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick).etc..complete in all floors complying with standard specifcation. Steel Adjustable telescopic props shall be provided as directed by the departmental Officers. (Payment for centering shall be given after the concrete is laid). a)For plane surfaces such as rectangular or square RCC columns etc

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall, etc. using mild steel sheets of size 1200cm x 60cm and 10 BG stiffened with welded mild steel angles of size 40mm x 40mm x 5 mm for boarding, laid with silver oak joists of size 10cm x 5cm & 7.5cm x 5cm as support runner, Top Horizontal stiffener spaced at about 60cm to 90cm centre to centre or at suitable intervals. MS Channel Section (ISMC 100) shall be provided as a vertical support @1.20m C/C and with Lateral support of Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) & steel pipes of 20mm dia @ required level/spacing etc. complete complying with standard specifcation and as directed by the departmental officers. (Payment for centering shall be given after the concrete is laid) A). Upto 2.10m Height of Shuttering

Supplying and erecting Shoring Shuttering with necessary supports to Retain Earth using mild steel sheets of size 1200cm x 60cm and 10 BG stiffened with welded mild steel angles of size 40mm x 40mm x 5 mm for boarding, laid with MS Channel Section (ISMC 100) as Horizontal stiffener provided at top, bottom and every sheet joints. MS Channel Section (ISMC 100) shall be provided as a vertical support @1.20m C/C with lateral support of Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) etc. complete complying with standard specifcation and as directed by the departmental officers. A). Upto 3.60m Height of Shuttering

Providing and laying in position, standardised concrete Mix M-20 Grade by insitumachine mix concrete adopting weighing batch method in accordance with IS 456using 20mm and down graded hard broken granite stone jelly for all RCC items of work swith minimum cement content of 325 kg/m3 and maximum water cement ratio of 0.55,including admixture (plasticiser / super plasticiser) in recommended proportions as perIS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5 Cu.m) 7730 kg. of 20mm machine crushed stonejelly and with about (3.3 Cu.m) 5156 kg. of 10-12mm machine crushed stone jellyand with about (4.79 cu.m) 7670 kg. of crushed stone sand, but excluding cost ofreinforcement grill and fabricating charges, centering and shuttering and also includinglaying, vibrating with mechanical vibrators, finishing, curing, etc. and providing ixtureslike fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra,etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS standards. (No separate payment will be made by the Department for the excess usage of materials). a)In foundation and basement

Providing and laying in position, Standardised Concrete Mix M-25 Grade by insitu machine mix concrete adopting weighing batch method in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 350 kglm3 and maximum water cement ratio of 0.50, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 Cu.m) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 Cu.m) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m’) 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by thedepartmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

In foundation and basement

In Ground floor

In First floor

In Second Floor

Providing and laying in position, Standardised Concrete Mix M-40 Grade by insitu machine mix concrete adopting weighing batch method in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 440 kg/m3 and maximum water cement ratio of 0.40, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m') 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials). a)In Ground floor

Manufacturing, supplying and fixing Precast Reinforced Cement Concrete slabs of 50mm thickness in RCC 1:2:4 (one cement, two sand and four aggregates), using following HBGS jelly excluding cost of reinforcement steel in position but including cost of moulding charges, casting of slab, finishing, curing and fixing in position in all floors etc., complete complying with standard specification and as directed.

75mm thick slab

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification.

Design and execution of post tensioning work, including decoiling, the strands, cutting to the required lengths, supplying, laying of HT strands sheathing (GI corrugated ducts 0.3mm thick) jointing with couplers and inserting the strands, profiling, fixing liveend anchorages, including supply of stressing anchorages, suitable for 5-5 & 5-4 tendons, grout vents, making dead end anchorages, including flowering the strands, fixing tendon support bars, supervising the fixing of antibursting reinforcement, stressing the cables, end trimming, grouting the cables, with cement slurry, mixed with admixtures with required tools, plants, and machineries, and consumables etc. (Shuttering, concreting & reinforcement steel shall be paid under respective items) at all heights including all leads, lifts, coordination, with the post- tensioning agency, preparation of drawings, obtaining approval from the Employer / Architect etc. Rate to include providing water, power, cement and admixture for grouting,packing of sheathing and anchorages blockings, filling of recess pockets after stressing using grouts (cement slurry mixed with approved admixtures) including providing access to post tensioning at all heights including all leads, lifts etc., all complete and as approved and as directed by the Employer Architect but excluding shuttering, concreting & reinforcement steel which shall be payable under respective items separately.

Plain Cement Concrete 1:2:4 (one cement, two sand and four hard broken stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers.

Manufacturing, supplying and fixing in position plain cement concrete precast kerb slab of size 600mm x 600mm x 100mm in Cement Concrete 1:2:4 (One cement, Two sand and Four jelly) using 20mm HBG stone jelly including cost of moulding charges, casting of slab, finishing, curing, fixing and pointing the slab with CM 1:3 (One Cement and Three Sand) to full depth of slab etc., complete complying with standard specification and as directed

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

In Ground Floor

In First Floor

Paving the Top of roof with Solar refelective ceramic tiles of size 305 x 305 x 7mm thick of approved quality and colour laid in Cement mortar 1:3 (One cement and three sand) 12mm thick laid with 4mm Spacer for joints and pointed with tile grout Water Resistant Tile Epoxy Grout for joint, curing etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by the Executive Engineer before use on works)

Paving the floor with best quality Double charged Vertified tiles 800 x 800 x 10mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three sand) 20mm thick in all floors with 3mm Spacer and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with best approved quality fine polished Granite Stone Slabs of size 1200 x 600 of 18 / 20mm thick of Synthetic Grey, Paradise and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Paving the floor with best approved quality Leather finished Granite slab Jet Black of 18-20mm thick with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Providing full nosing to the steps or platforms to the Granite slab of 20mm thick including neat finishing, polishing, cost of powder, tools etc as directed by the departmental officers

Flooring with Self Designed Colour Ceramic Tiles of following size and variety conforming to IS 15622 laid over cement mortar bed of 20 mm thick in cement mortar 1:3 (One Cement and Three crushed stone Sand) with required Cement Slurry and Mortar Plasticizer including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with Water Resistant Tile Epoxy Grout at the rate of 0.27 Kg. / sq.m. etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Dadooing Ceramic Tiles of size 300mm x 600mm x10mm best approved quality, white / colour glazed tiles set in Cement Mortar 1:2 (One Cement and Two sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. /sq.mneatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.

Paving the floor with pre-polished concrete anti-skid tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers.

Providing Polymer Coating (Water Proof Coating) for sunken Portion of toilet with following specification and the surface shall be cleaned to remove all dust, foreign, matters lose materials or any other deposits of contamination by rubbing with wire brush. Slurry: Dry blend and polymer liquid blend shall be mixed into the desired ratio as per recommendation of the supplier. The mix shall be stirred throughly until no bubbles remain in the mix. Any lumps found in mix shall be removed. Apply first coat of polymer modified cementitious slurry by brush on wet cleaned surface. After drying, second coat shall be applied on the first coat as directed by the departmental officers etc. The rate inclusive of cost of materials and labour, etc., complete.

Supplying and fixing in position 160mm dia PVC Pipe best approved of BIS quality PVC rain water down fall pipes various dia having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Supplying wrought fixing Ornamental Teakwood entrance door as per the drawing and designs approved by the departmental officers. The size of the opening is 2.10X 2.40. The outer frame of the door is 150mmx125mm teakwood. The main door shutter opening size is 1.80 X 2.03m. The main door should be double leaves and each door shutter fully panelled. The door panells shall be of 50mm thick teakwood planks with ornamental designs approved by the Executive Engineer. The Lock rail and bottom shall be of 200 x 50mm tk teakwood, top rail 230x50mm tk teakwood. The door frames and shutters shall be given of cost of best approved quality melamine finish. The rate inclusive of cost of approved quality teakwood, 10mm thick designed toughedned glass Special type Heavy Brass Aldrop 300mm X 20mm. Special type heavy Brass tower bolt 300mm Length. Special type heavy Brass tower bolt 250mm Length. The cost includes cost of material, labour charges, conveyance charges, fixing charges, designing charges and glass design charges, electricity charges and all other incidental charges., etc. All materials should be got approved by the Executive Engineer before use on works.

Supplying ,fabricating and fixing in position of Country wood Door frame without bottom frame, of size 100X60mm rectangular section with necessary rebate 30mmX15mm, to host the shutter,using of right butt joint riveted hold assembly with nylon insert,not be welded with special purpose hard ware.Proclaimed including phopating as per ISI with rust preventive primer ready to assemble condition for easy installation at site including dismantling,making necessary chipping and holes in RCC columns, walls with power drills to the extent required etc complete.The cost includes the cost of hold fast ,plastic bush, insert receiver,rubber bottom,shock absorber etc complete as directed by the departmental officers in all floors.

Supplying and fixing Single leaf solid core particle board flush shutter of nominal thick of 35 mm with necessary T.W. internal lipping conforming to IS 2302 with both sides alround commercial ply 35mm thick including supplying and fixing cost of wind appliances and furniture fittings such as 1no .200x12mm tower bolt 2nos. 150x12mm tower bolts 1no. 250x16mm aldrops, 3 nos. 200mm ‘D’ type door handle and door stopper with bush etc., complete as directed by the departmental officers.

Supplying & fixing of WPC (Wood Polymer Composite) Door, Frame extruded with size 75mm x 50mm. The single core door made of rigid WPC compound with minimum Bulk Density of 900 KG/ Cub.Mt. & shore hardness of 55. Supplying & fixing of WPC door shutter, extruded as a single core board with rigid WPC compound with the thickness of 25mm (+/- 1mm) & minimum Bulk Density of 550 KG/ Cub.Mt. & shore hardness of 55. For the aesthetic appearance, the door shall be a printed digitally on one side of the shutter. The WPC door shall be fixed onto the WPC frame with 3 Nos of 5” SS Hinges and the door shall have 2 towerbolt on one side and 1 towerbolt or aldrop on other side for locking system and 2 numbers of handle on the either side of the door shutter, all made of aluminium.The rate is inclusive of all materials, labours, conveyance and fixing in position with all other incidential charges etc., complete complying with standard specification and as directed by the departmental officer.( The materials quality,brand, colour, shade should be approved by the Executive Engineer before use on works).

Supplying and fixing of WPC swing door, extruded as a single core board with rigid WPC compound with the thickness of 25mm (+/- 1mm) & minimum Bulk Density of 550 KG/ Cub.Mt. & shore hardness of 55. The door shall be a plain matt board .The WPC door shall be fixed onto the Aluminium “G” type channel with Wheel and the door shall have 2 Hooks in SS, 2 Handles 6” in SS, with neccessary locking arrangements etc.The rate is inclusive of all materials, labours, conveyance and fixing in position with all other incidential charges etc., complete complying with standard specfication and as directed by the departmental officer.( The materials quality,brand, colour, shade should be approved by the Executive Engineer before use on works).

UPVC Window Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work

UPVC Ventilator Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Manufacturing supplying and fixing of Single leaf steel door Single leaf with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Supplying ans fixing in position of Modular Stainless steel railing with toughened glass insertion with following specification. The stainless steel shall be of 304 grade. The top hand rail shall be 50mm dia and 1.6mm thick. The vertical balusters shall be 38mm square tube and 1.00mm thick all joints shall be finished smoothly with necessary fittings and clamps. The toughened glass shall be 12mm thick and fixed with vertical balustrades with necessary ss clamping arrangements.The rate is inclusive of all materials, labours, conveyance and fixing in position with all other incidential charges etc.,complete complying with standard specfication and as directed by the departmental officer.( The materials quality,brand, should be approved by the Executive Engineer before use on works)

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between.The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete complying with standard specification.

Supplying and fixing of M.S.Grill of approved design for grill gate, grill work to doors and windows openings ramp etc., using necessary mild steel flats for inner and outer members which should be fixed on edges including priming coat of best approved quality red oxide primer etc., complete complying with standard specification.

Providing suspended Hilux Board (10mm thick) False Ceiling of the following types with G.I. perimeter channel of size 0.55mm tk (having one flange of 20mm and another flange of 30mm and a web of 27mm) along with perimeter of ceiling , screw fixed to brick wall/ partition with the help of nylon sleeves and screws at 610mm centres. Then suspending G.I. Intermediate channel of size 45mm (0.90mm thick with two flanges of 15mm each) from the soffit at 1200mm centres with ceiling angle of 25mmx 10mmx0.50mm thick fixed to soffit with G.I Cleat and steel expansion fastners ceiling section of 0.50mm thickness having knurled web of 51.50mm and two flanges of 26mm each with lips of10.50mm are then fixed to the intermediate channel at 457mm centres. 12.50mm tapered edge Gyp board (confirming to is 2095-1982) is then screw fixed to ceiling section with25mm dry wall screws at 230mm centres. Screw fixing should bedone mechanically either with screw driver or with drilling machine with suitable attachment got approved by the Executive Engineer before use on works in etc., complete complying with standard specification.

Providing Cornice Work for Gyp Board False Ceiling etc., complete in all floors complying with standard specification and as directed by the departmental officers.

Supply and installation of Anutone (or) Euivalent Brand of Acoustical False Ceiling of subtex nubby, square edge, glass fibre core fully encapsulated ceiling tile of size 595 x 595 x 15mm having volume density 120 Kgs / m3, weight 1.8 / 2.4 / 3 kg / m2 which is suspended by using 0.3mm thick skelet trelis T15 metal grid system. Skelet trelis T15 metal grid system of 600 x 600mm module includes skelet WA15 W30 wall angle with unequal flanges of 15 / 19mm, length 3000mm, fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300mm centers. Then suspend the skelet MT15 W36 MainT with flange width 15mm, height 32mm and length 3600mm, from the soffit slab with help of soffit cleat and wire rod with leveling spring clip at 1200mm centres. Skelet CT15 W12 CrossT with flange width 15mm, height 26mm and lengt 1200mm is interlocked into the pre-cut slots in the Main T15 at 600mm centers in the perpendicular direction to the Main T15. Finally, the skelet CT15W06 CrossT with flange width 15mm, height 26mm and length 600mm are interlocked into the precut slots in the CT15W12 CrossT in direction parallel to the Main T15 to result in 600 x 600mm module. The subtex nubby square edge of size 595 x 595 x 15mm shall be placed into the grid size of 600 x 600mm. Ensure arrow marks behind the tiles are oriented in one direction to achieve uniform shade. The systems to achieve noise reduction coefficient not less than 0.9 NRC, so as to have an neat appearance as directed by the department offices. The cost includes, cost of material, cost of labour, scaffolding, transportation, conveyance, etc. complying to standard specication.

Supplying and fixing fine polished cuddapah slab of 38 / 40mm thickness for cup-board arrangements including laying to correct alignment with necessary cement mortar and black powder etc, complete complying with standard specification and as direct.

Providing Cup-board Shutter using termite / water proof plywood of 19mm thick over which laminated sheet of 0.8mm thick fixed inside the shutter and 1mm thick fixed in the outside of the shutter using fevicol along with necessary furniture fittings, such as, hydralic hinges, tower bolt, handles, multi purpose locks etc., as directed by the Departmental Officers. The design pattern, water proof plywood, laminate sheet and other materials should be got approved from the Executive Engineer befoe use on work.

Providing and fixing Acoustic wall Panelling (equivalent ot Armstrong ) in channelled wood works perforated panels of width 192mm, thickness of 15mm and length of 2400mm or as per required by the Departmental Engineer made of a high density fibre board with minimum 725 kg./m3 density substrate with a laminated facing as per the approved shade and finish and a melamine balancing layer on the reverse side. The boards shall have a special peforation pattern where the visible surface has a "Helmholtz"fluted perforation of 3mm width and 21mm of visible panel each. The edges of the panels shall be "tongue" and grooved" to receive special clips for installation. The back of the perforated panel shall have sound absorbing not woven acoustical fleese having NRC of 0.52. The panels shall be mounted on special aluminium splines using clips provided by Armstrong and approved by the Engineer-in-Charge.

Providing and fixing of Aluminium Composite Panel (ACP) 4 sided having 50 x 25 x 1.50mm frame work vertical and horizontals out of specially designed extruded sections withstand wind pressure of 180 Kg/sq.m and fabricated fixed at all level elevation and heights. The extruded section cutting and fixing required space extruded section shall be of 6063 and alloy of BSH 9 confirming T is – 63400 rate shall included to fix the main frame with necessary clamps, fasteners, bolt nuts etc. The main frame of extruded section shall be of 22843 & 22739 (H9) grade conforming to BS 4174 (or) IS 8147. Rate shall included 4mm thick ACP sheet (0.25 + 3.5 + 0.25) alstrong or equivalent fixing with spacer tape and the ACP sheet bounded with special type structural sealant of dow corning 789 or equivalent in dust free conditions the gaps between ACP sheet to be filed with whether sealant and backer rod or 12mm foam sheet to ensure water and air tightness in all complete complying with standard specification as directed by the departmental officer

Providing and Laying wetmix mecadam of 150 mm compacted thickness in 2 layers of 75 mm thick or else as specified on the prepared sub base with grade store aggregate and granular material of quality size and grading pasting in layer with motor grader and compaction with vibrating orller of 80/100 KN static weight and fine dressing for required grade and cross slope as shown on the drawing equipments safty measures as per MORTH & 406

Supplying and laying Rubber moulded Hydraulic pressed Paver Block of 83mm thick approved design made out of 6 - 10mm thick HBGS chips in cm 1:2:4 properly occurred to attain the required strength laying the Rubber Moulded Paver Block over a sand cushion of 10cm thick and well compacted using 1-3 tonne capacity of manufacturing the inter locking blocks , loading, transportation , unloading and other incidential charges etc. complete complying with standard specification

Plastering with Cement Mortar 1:5 (One cement and Five sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Sand) 10mm thick used finishing including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Plastering the surface of walls with Cement Mortar 1:3 (One cement and Three sand), 12mm thick used finishing in all floors including curing etc., complete complying with standard specification and as directed by the departmental officers.

Plastering with Cement Mortar 1:4 (One Cement and Four Sand) 20mm thick finishing in all floors including curing etc., complete complying with standard s conforming to BIS at 2% by weight of cement used including finsihing, curing, etc., complete in all floors complying with standard specification and as directed by the departmental officers.

Providing Wall Putty including labour charges etc., complete in all floors complying with standard specification and as directed by the departmental officers.

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting the wall two coats with approved weather proof Exterior Emulsion paint over one primer coat of over cement plastered wall surface ect., complete complying with standard specification.

Painting the wall with Texture Finish Paint including labour charges over one primer coat of over cement plastered wall surface ect., complete complying with standard specification.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification.

Painting new wood work with two finishing coats of synthetic enamel ready mixed paint of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification.

Supplying, laying and jointing 25 mm dia CPVC Pipe OF Standard Dimension Ratio 11 (Pressure class 1) conforming to IS:15778 - 2007 of approved quality and best variety of the following dia including cutting and fixing CPVC specials using CPVC adhesives (Solvent Cement) (but excluding cost of such specials) and fixing into wall with teak wood plugs, CPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications and as directed by the departmental officers. (The CPVC pipes shall be got approved by Executive Engineer before use on works) - Internal water supply above ground level.

Supplying CPVC Specials of SDR 11 Conforming to IS 17546-2021 in water supply arrangements (both in internal and external water supply arrangements

25 mm dia CPVC Elbow

25 mm dia CPVC TEE

25 mm dia CPVC Union

25 mm dia CPVC Nipple

Supplying, laying and jointing UPVC pipes of Class 5 (having working pressure of 10 kg/sq.cm) conforming to IS 4985- 2000 of approved quality and best variety of the following dia including cutting, and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) in accordance with IS 7634-3(2003) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the ismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard pecifications. The UPVC pipes shall be got approved by Executive Engineer before use on works. - Internal water supply - above ground level.-Internal Water Supply Arrangements using UPVC pipes and UPVC specials

25 mm dia UPVC Pipe

32 mm dia UPVC Pipe

40 mm dia UPVC Pipe

50 mm dia UPVC Pipe

Supplying, laying and jointing 40 mm dia UPVC Pipe of Class 5 (having working pressure of 10 kg/sq.cm) conforming to IS 4985- 2000 of approved quality and best variety of the followingdia including cutting and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) in accordance with IS 7634-3 (2003) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the ismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works - External water supply above ground level / Below ground level.-External Water Supply Arrangements using UPVC pipes and UPVC specials

Supplying UPVC Specials (with working pressure 10 kg. / sq.cm.) in water supply arrangements (both in internal and external water supply arrangements

25 mm dia union

32 mm dia union

40 mm dia union

50 mm dia union

25 mm dia Elbow

32 mm dia Elbow

40 mm dia Elbow

50 mm dia Elbow

25 mm dia Tee

32 mm dia Tee

40 mm dia Tee

50 mm dia Tee

32 x 25 mm dia Reducer

25 x 20 mm dia Reducer

20 x 15 mm dia Reducer

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work.

25 mm dia G.M. Gate Valve

32 mm dia G.M. Gate Valve

40 mm dia G.M. Gate Valve

50 mm dia G.M. Gate Valve

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm colour glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position Colou glazed European Water Closet 10 litre capacity PVC flushing tank fixed on to wall of best quality and approved make with 100 mm "P" or "S" trap connecting with PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications.

Supply and fixing in position of best Indian make white glazed earthernware lipped mouth flat back urinal of best quality and approved make of size 430mm x 260mm x 350mm with GI pipe, 32mm dia bell mouth PVC connection and waste pipe, 15mm dia GI pipe of required length, 15mm dia GM wheel valve, 15mm dia brass nipple 2 Nos., and fixing the urinals in position with necessary TW plugs, clamps, screws, etc., including dismantling masnory and re-doing the same to the original condition, etc., including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage etc. complete complying with standard specifications and as directed by the departmental officers.

Supplying and fixing in position best quality and approved make Indian made Colour Glazed Wash Hand Basin Without Pedestal of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification

Supplying and fixing best approved best quality brass CP soap tray of size 150 x 150mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications.

Supplying and fixing approved best quality brass CP towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications.

Supplying, laying and jointing glazed stoneware pipes of 110mm dia of approved best quality with spigot and socket ends (in reverse direction) in dry condition and laid in loose joints (i.e.) without cement and spun yarn, so that the waste water can be drained to the trenches already available, excluding cost of earth work excavation, cost of re-filling with sand / earth, but including laying the pipe in true alignment and gradient and conducting required water supply test for draining with necessary tools and plants, etc., complete complying with standard specifications.

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level

75mm dia PVC soil / waste pipe

110mm dia PVC soil / waste pipe

160mm dia PVC soil / waste pipe

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications.

75mm dia PVC Elbow

75mm dia PVC Tee

75mm dia PVC Tee with single door

75mm dia PVC Bend

110mm dia PVC Elbow

110mm dia PVC Tee

110mm dia PVC Tee with single door

110mm dia PVC Bend

Supplying and fixing position PVC Nahani Trap / Floor Trap of the 100 x 75mm with stainless steel gratings sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the PVC pipes, etc., complete complying with standard specification.

Supplying and fixing PVC ventilating shaft of 110mm dia (having working pressure 4 kg. / sq.cm) with 3 metre height including cost of PVC cylindrical cowl of best approved quality etc., complete complying with standard specifications and as directed by the departmental officers

Supplying and fixing in position CI manhole covers with CI frames (Heavy duty) of size 60cm x 60cm of best approved quality as per standard specification etc., complete compying with standard specifications

Supplying and filling 20mm guauge HBGS stone jelly for dispersion trench including loading conveying and unloading and as directed by the departmental officers etc. complete complying with standard specification.

Supplying and filling 40mm guauge HBGS stone jelly for dispersion trench including loading conveying and unloading and as directed by the departmental officers etc. complete complying with standard specification.

Supplying and erecting 2H.P monoblock with ISI mark with necessary accessories (motor should be got approved by Executive Engineer before use onworks) complete complying with standard specification.

Supplying and fixing of PVC ready made HDPE water storage tanks having 1000 litre capacity made of PVC matertials including necessary provision for conveying, jointing delivery line etc.

Providing Anti-termite treatment to soil adjecent and under building foundation, plinth periphery of the building by application of chemicals of IS 63613 part I to IV in stages to suit the progress of work consist as per the detailed specification as below. Including breaking of termite mounds, making holes with crow bar, closing the holes after the treatment and including cost of chemicals, labour charges, transport and storing etc., complete and as directed by the departmental officers.

Manufacturing, Supplying and Erection in position of 100 liter twin plastic dustbin with stand ,complete as directed by the departmental officers.

Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking at site dump manure from approved source, including carriage upto 5 km lead complete (manure measured in stacks will be reduced by 8% for payment).

Uprooting rank vegetation and weeds by digging the area to a depth of 60 cm, removing all weeds and other growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of all rubbish with all leads and lifts.

Providing and laying Neelgiri/Mexican grass turf with earth 50mm to60mm thickness of existing ground prepared with proper level andramming with tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly, as per direction of officer-in-charge

Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, herbs, edge, flower beds, foliages, creepers etc. including hoeing,weeding, pruning, replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter, removal of garden waste, applying insecticide, pesticide & fertilizers(whenever required) top dressing of lawn with good earth and manure and maintenance of other garden related works as directed by office-incharge (Cost of Good Earth, Manure, Fertilizer, Insecticide, Pesticide will be provided by the Department & lawn mover and brush cutter with fuel and other T & P material/articles shall be provided by the contractor.) and as per direction of officer in charge

Supplying and planting of ORNAMENTAL Flowers or various variety and arranged in such a manner red soil including conveyance at site of works and planting at the places shown by the departmental officers including cost of manuring and maintaining for 180days etc.,.The rate excluding of all taxes and includes cost of all materials, labour,transports and other incidental charges, including providing in the position to the rooms as directed by departmental officers.

Barderplaints (Hemalis patten,Exora, Alamanda, Ujaniva)

Foliage Shrubs ( Clerodendron, Nicodia)

Hedge Plants ( Golden Dhurandha )

Single Trunk Palm (Foxtail Palm)

Multi trunk palm (Areca palm)

Ground Covers ( Panthanus, BlackLilly, Landana purple, Ibiscus, Arali)

Supply and fixing of Swing 2-Seater with Rubber Seat: A-Frame :1 ½” Galvanished ‘B’ class pipe Top Rail : 2” Galvanished ‘C’ Class Pipe Seats : Rubber Chain : 8mm Stainless Steel Chain (Grade-304) Greater Chennai Corporation Playfield Department SCHEDULE OF RATES 2023-24 Chain : 8mm Stainless Steel Chain (Grade-304) Painting with PU coating Product area: 10’ft * 9’ft Play area :15’ft * 15’ft . The good quality of materials used and all other arrangements etc, including priming coat fixing in position with all necessary accessories complete complying with standard specification and as directed by the departmental officers.

Spiral Slide Senior FRP: [Component] Ladder :Galvanished ‘B’ Class pipeSlide : FRP Spiral slide BED LEG :Galvanished ‘C’ Class pipe [Measurement] Height :6 ½ ft.FRP thickness 6mm. (Reinforced Polymers in 7 Layers) 450 CSM Matt, 600 Roving mat, Isotolic gel coat with UV pigment. Painting with PU coating Painting with PU coating width :10ft [Required area] Product area: 6’ft * 10’ft Play area :8’ft * 15’ft The good quality of materials used and all other arrangements etc, including priming coat fixing in position with all necessary accessories complete complying with standard specification and as directed by the departmental officers.

Supply and fixing of Roller Slide 8ft: Measurement] Height:5ft Width: 2ft Sliding Chute:10ft Roller thickness:3mm PVC Roller with½ inch galvanished pipes. No. of Rollers.46 with multicolours. Painting with PU coating [Required area] Product area: 21/2’ft * 14’ft Play area:6’ft * 18’ft The good quality of materials used and all other arrangements etc, including priming coat fixing in position with all necessary accessories complete complying with standard specification and as directed by the departmental officers.

Supply and fixing of Sea – Saw 2 seater – FRP 24 CPE-128 Height: 20” width:96’’ X 30’’ pa frame:11/2’’ GI pipe,2.5mm thickness, B Class, arm:2”GI pipe, 4mm thickness, C class. Paint:pu coating. FRP seat with 450csm, seat size 15”*14 The good quality of materials used and all other arrangements etc, including priming coat fixing in position with all necessary accessories complete complying with standard specification and as directed by the departmental officers.

Supply and fixing of Merry go round – 6 Seater (FRP) Height :3” GI Pipe, 2.5mm thick, b class Seat size:15” X 14”, paint: pu coating. The good quality of materials used and all other arrangements etc, including priming coat fixing in position with all necessary accessories complete complying with standard specification and as directed by the departmental officers.

Supply and fixing of Horse Rider: [Component] LEG :Galvanished ‘C’ Class pipe Galvanished ‘B’ Class pipe Spring: Mild steel spring horse : FRP with Isotolic gel coat with UV pigment. Painting with PU coating [Required area] Product area: 3ft*3ft Play area:5ft*5ft [Measurement] Width:3ft. The good quality of materials used and all other arrangements etc, including priming coat fixing in position with all necessary accessories complete complying with standard specification and as directed by the departmental officers.

Supply and fixing of Duck Merry Go Round: [Measurement] Height:2ft Width:7ft [Component] LEG :3” Galvanished ‘B’ Class pipe Seat :FRP Duck -4Nos. with Isotolic gel coat with UV pigment. Support : 1 ½” Galvanished ‘B’ Class pipe. Painting with PU coating [Wanted area] Product area : Ø 7’ft Play area : Ø 9’ft. The good quality of materials used and all other arrangements etc, including priming coat fixing in position with all necessary accessories complete complying with standard specification and as directed by the departmental officers.

Supply and fixing of Jungle Gym: [Component] Galvanished ‘B’ Class pipe painting with PU coating [Required area] Product area :5’ft * 5’ft Play area: 7’ft* 7’ft. The good quality of materials used and all other arrangements etc, including priming coat fixing in position with all necessary accessories complete complying with standard specification and as directed by the departmental officers.

Supply, Erection of 7m Free Standing Double Arm Bracket 8 sided Octogonally continously tapered structured pole with base plate of size 250 x 250 x 12mm as per IS-875 with following specification. Bottom Pole Dia - 140mm Top Pole Dia - 70 mm Thickness of Pole - 3 mm The pole should be hot dip galvanized confirming to BESN ISO-1461 with thickness of 65 Micron.

Supply & Fitting of 60W LED Street Light Fitting with LED for the poles

Supply & Fixing of 20 wp solar panel based decorative light12 Ah lipo 4 batteryUV proof AL Alloy battery

SITC of Minimast (12 Metre) with 6 Nos. 150W LED Fitting - m-2137

Supply and laying of 4 x 16 sq.mm PVC LTUG aluminium armoured cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good

Supply and laying of 4 x 6 sq.mm PVC LTUG aluminium armoured cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board of double door type with metal door with IP43 protection with 1 No. 32A DP MCB as incoming and 6 Nos. 6A to 32A SPMCB outgoing in flush with wall and making good of the concealed portion with earth connection only. The MCB DB and MCB's should be with ISI mark (like standard make

Supply and fixing of 65mm (2-1/2") GI pipe (Class 'B') of 6 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom with concreting with construction of masonary pedestal with suitable MS box to house 5A control switch 16A fuse unit (500V) etc with suitable angle iron frame work with door and with lock and key arrangements and with supply and fixing of 4'40W twin street light fluorescent fitting with copper chokes and condenser with fluorescent tubes with 1 metre of 32mm dia GI pipe (Class 'B') complete with necessary clamps on the above post with PVC unsheathed FRLS leads with painting of suitable colour

Supply and run of 1 of No.8 SWG GI wire for earth connection, including cost of all materials etc. all complete in all respects complying with relevant standard specification and as directed by the departmental officer

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry

Supply and fixing of 5A or 10A or 20A AC single phase 230V, 50 Hz Watt hour metre on suitable TW box complete with earth connections

Supply of LED Bollard light fitting of 11W with pressure die cast aluminium housing body for optimal thermal dissipation. Lamp compartment comprising of anti glare clear diffuser with Injection moulded polycarbonate/clear glass material, delivering superior light output. Rated life Burning Hrs 50000 hr @ Lumen Maintenance of 70%, CCT > 5500K, IP 66 optical and electrical compartment & impact resistance of complete luminaire > IK08.

Wiring with 2x1.5 sqmm PVC insulated Single Core unsheathed FRLS copper Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories with Module GI switch box inflush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sqmm copper wire and making good of the concealed portion with suitable colour for concealed PVC Light point/ Fan Point (For electronic regulator) (5 Points Per Coil) (Higher end)

Wiring with 2x1.5 sqmm PVC insulated Single Core unsheathed FRLS copper Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories with Module GI switch box inflush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sqmm copper wire and making good of the concealed portion with suitable colour for concealed PVC Light point/ Fan Point (For electronic regulator) (6 Points Per Coil) (Higher end)

Wiring with 3x1.5 sqmm (22/0.3) PVC insulated Single Core unsheathed FRLS copper Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories with Module GI switch box inflush with wall with 6A two way module switch with module front plate with continuous earth wire connection of 1.5 sqmm copper wire and making good of the concealed portion with suitable colour for concealed PVC stair case Light point (Higher end)

Supply and fixing of single box type 4'20 W LED flu Fitting (Higher end) complete with electronic driver with TW round block on wall or ceiling with flu. LED Tube with PVC unsheathed leads from terminals to the fitting (SD-443)

Supply and fixing of 18W LED Square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting

Supply and fixing of 18W LED Round type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting

Supply and fixing of battorn holder with 9W LED lamp for BH point for Night Lamp

Supply and fixing of LED foot lamp on wall with PVC unsheathed copper leads from terminals to the fitting

Supply and fixing of LED Fancy wall bracket on wall with PVC unsheathed copper leads from terminals to the fitting

Supply and fixing of WT bulk head fitting with guard (Higher end) suitable with 7W/9W LED bulb

Supply and fixing of 20W LED mirror light battern with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of 1200mm (48") sweep AC ceiling fan High speed complete (Higher end) with 2 module 100W fan step regulator (Higher end) with 600mm down rod on the existing fan clamp.

Supply and fixing of 300 mm (12 inch) sweep modular AC exhaust fan complete necessary without provision of hole in the wall.

Supply and fixing of louver shutter arrangements for 300 mm (12") sweep (light duty) AC exhaust fan

Supply and fixing of 3 Nos. 6A two module 5 pin socket, 3 Nos 6A one module switch with module cover plate (Plastic) on suitable module concealed box (GI) inflush with wall with connections. (Higher end)

Supply and fixing of 1No 6A/16A two module socket, 1 No 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI) inflush with wall with connections. (Higher end)

Supply and fixing of 20 Amps DP Plug and Socket in sheet enclosure with 32A DP MCB in flush with wall with earth connection (For AC Plug) (Higher end)

Supply and fixing of 32A FP MCB in suitable sheet steel enclosure in flush with wall with earth connection (Higher end)

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure Distribution board with Double Door (Metal) with 1No. 32 Amps DP MCB as incoming and 10 No’s 6 Amps to 32 Amps SP MCB as outgoing in flush with wall with earth connection only. (Higher end) (LDB)

Supply and fixing of 7 segment 4 way TPN MCB sheet steel distribution board (Higher end) with metal /acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one no. 4 pole incoming MCB / Isolator and another seperate 4 way provision for accomodating one no. 4 pole ELCB / RCD (totally 8 ways in one segment) (3x 4 ways in each segment) and seperate provision for MCB / Isolators (Totally 12 nos.) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm with the following inflush with wall with earth connection only. (SD-636) (Main Lighting DB for each floor) Incoming: 63A FP MCB & 63A ELCB -1 No., Outgoing: 32A SP MCB -12 Nos.

Supply and Fixing of 3 Ph 8 way Vertical type MCCB DB with IP 43 protection Double door type DB (legrand) with 1No 160A 4P MCCB 16KA as incoming and 6 No's 63A TP MCB 10 KA & 2 No's 32A TP MCB 10 KA as outgoing with cable entry box on suitable angle iron frame on wall with earth connection only. (Higher end) (Main Lighting Sub Switch Board for entire block) & MPDB

Supply and fixing of cheminey for- Kitchen with connection complete

Supply and fixing of 1000W automatic electric water heater of 25 leters capacity suitable for 230V 50 C/s AC supply on suitable MS clamps with 3 core flex wire bt without plumbing work.

Supply and fixing of TV socket for smart TV with recesses mounting box with cover plate

Supply and fixing of Telephone socket with flush mounting box with cover plate

Supply and fixing of Double pole switch with flush mounting box with cover plate

Supply and run of 2 of 2.5 sq mm PVC insulated SC unsheathed FRLS copper Conductor of 1100V Grade in suitable PVC rigid pipe concealed in wall and ceiling with contineous earth wire connection of 2.5 sqmm copper wire with and making good of the concealed portion.

Supply and run of 2 of 4.0 sq mm PVC insulated SC unsheathed FRLS copper Conductor of 1100V Grade in suitable PVC rigid pipe concealed in wall and ceiling with contineous earth wire connection of 4.0 sqmm copper wire and making good of the concealed portion with suitable colour.

Supply and run of 4 of 4 sq mm PVC insulated SC unsheathed FRLS copper Conductor of 1100V Grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 4 sqmm copper wire and making good of the concealed portion

Supply and run of 4 of 10 sq mm PVC insulated SC unsheathed FRLS copper Conductor of 1100V Grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 10 sqmm copper wire and making good of the concealed portion

Supply and run of 4 of 25 sq mm PVC insulated SC unsheathed FRLS copper Conductor of 1100V Grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 25 sqmm copper wire and making good of the concealed portion

Earthing as per the ISI specification with an earth electrode of 2.1 mt class 'B' GI pipe of dia not less than 40mm, with copper earth plate of size 125mmx50mmx6mm, with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry

Supply and run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall/floor/ground for earth connection

Supply erection, testing and commissioning of 2.0 TR (6000 K.cal/Hr) ABS Plastic Split type Air conditioner conforming to IS 1391 (Part-2) 1992 with Amdt No. 1 to 2 fitted with rotary compressor operating on refrigerant R-32/non CFC suitable for wall mounting for operation on 230V, 50HZ single phase AC supply with star rating of 5 star as per BEE specification and capable of performing the functions of

Supply of 5 KVA Electronic Automatic Voltage Stabilizer (Higher end) with Input Voltage range of 170 Volt – 270 Volt and Output Voltage range 200 Volts to 240 Volts with High and Low Voltage cut off and 3 minutes time delay relay with demonstration.

Supply and fixing of water drain pipe line (1" PVC pipe)

Supply and fixing of MS stand for fixing Outdoor unit.

Supply and laying of 5/8" and 3/8" copper refrigerant pipe of 0.8mm thick with 2.5 sqmm 3 core chord between indoor and outdoor unit. (Extra beyond 3 mts supplied with AC unit)

Supply and installation of ISDN compatible EPABX System configured with 6 Trunk, 10 SIP Trunk lines+64 analog extension which is expandable upto 96 analog extensions + 112 IP Port. (Higher end) Intercom

Supply & Fixing of Caller ID telephone with speaker tone/pulse Switchable redial, flash with necessary connections. (Higher end) Intercom

Supply, fixing and termination of Legrand/ D-Link I/O Socket for Telephone with Single Socket RJ-11 Face Plate and CAT 6 PVC Module Box with necessary connections. Intercom

Supply and fixing of 25mm PVC rigid pipe concealed in wall and ceiling in suitable PVC rigid pipe on wall with Delton/ Polycab unarmoured 0.5mm 2 pair Telephone cable etc ceiling.Intercom and making good of the concealed portion with suitable colour.

Supply and erection of 2 KVA 1 Phase UPS (Single Phase In & Single Phase Out) System with Battery and 2 hours back-up.

Wiring with 2x1.5 sqmm PVC insulated Single Core unsheathed FRLS copper Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories with Module GI switch box inflush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sqmm copper wire and making good of the concealed portion with suitable colour for concealed PVC Light point/ Fan Point (For electronic regulator) (5 Points Per Coil) (Higher end)

Supply and fixing of single box type 4'20 W LED flu Fitting (Higher end) complete with electronic driver with TW round block on wall or ceiling with flu. LED Tube with PVC unsheathed leads from terminals to the fitting

Supply and fixing of 18W LED Round type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting

Supply and fixing of 24W LED 2x2 square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed FRLS copper eads from terminals to the fitting

Supply and fixing of WT bulk head fitting with guard (Higher end) suitable with 7W/9W LED bulb

Supply and fixing of 25 W Recess mounted downlighter with pressure die-cast aluminium heat sink & PC Lens used to enhance the aesthetic of the fixture with Independent electronic LED driver

Supply and fixing of 450 mm (18") (Higher end) AC wall mounted fan complete on wall with connection

Supply and fixing of 1 no.6A two module 5 pin socket, 1 no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. (Higher End)

Supply and fixing of 3 Nos. 6A two module 5 pin socket, 3 Nos 6A one module switch with module cover plate (Plastic) on suitable module concealed box (GI) inflush with wall with connections. (Higher end)

Supply and fixing of 1No 6A/16A two module socket, 1 No 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI) inflush with wall with connections. (Higher end)

Supply and fixing of 1No 16A two module switch with module cover plate (plastic) on suitable module concealed Box (GI) inflush with wall with connections. (Higher end)

Supply and fixing of 1No 6A/16A two module socket with module cover plate (plastic) on suitable module concealed Box (GI) inflush with wall with connections. (Higher end)

Supply and fixing of 2 Nos 6A/16A two module socket, 2 Nos 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI) inflush with wall with connections. (Higher end)

Supply and fixing of 32A DP MCB in suitable sheet steel enclosure in flush with wall with earth connection (Higher end)

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure Distribution board with Double Door (Metal) with 1No. 32 Amps DP MCB as incoming and 10 No’s 6 Amps to 32 Amps SP MCB as outgoing in flush with wall with earth connection only. (Higher end) (LDB)

Supply and fixing of 7 segment 4 way TPN MCB sheet steel distribution board (Higher end) with metal /acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one no. 4 pole incoming MCB / Isolator and another seperate 4 way provision for accomodating one no. 4 pole ELCB / RCD (totally 8 ways in one segment) (3x 4 ways in each segment) and seperate provision for MCB / Isolators (Totally 12 nos.) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm with the following inflush with wall with earth connection only. (SD-636) (Main Lighting DB for each floor) Incoming: 63A FP MCB & 63A ELCB -1 No., Outgoing: 32A SP MCB -12 Nos.

Supply and Fixing of 3 Ph 8 way Vertical type MCCB DB with IP 43 protection Double door type DB (legrand) with 1No 160A 4P MCCB 16KA as incoming and 6 No's 63A TP MCB 10 KA & 2 No's 32A TP MCB 10 KA as outgoing with cable entry box on suitable angle iron frame on wall with earth connection only. (Higher end) (Main Lighting Sub Switch Board for entire block) & MPDB (DATA-5)

Supply and fixing of 48W LED street light fitting with heat resistant toughened glass with IP 65 Prtection in suitable dia GI pipe (Class 'B') complete on the existing post or wall with PVC unsheathed Copper leads MS clamps and aluminium painting (Higher end)

Supply and run of 2 of 2.5 sq mm PVC insulated SC unsheathed FRLS copper Conductor of 1100V Grade in suitable PVC rigid pipe concealed in wall and ceiling with contineous earth wire connection of 2.5 sqmm copper wire with and making good of the concealed portion.

Supply and run of 2 of 2.5 sq mm PVC insulated SC unsheathed Cu. Conductor of 1100V Grade in suitable PVC rigid pipe concealed in wall and ceiling and making good of the concealed portion

Supply and run of 2 of 4.0 sq mm PVC insulated SC unsheathed FRLS copper Conductor of 1100V Grade in suitable PVC rigid pipe concealed in wall and ceiling with contineous earth wire connection of 4.0 sqmm copper wire and making good of the concealed portion with suitable colour.

Supply and run of 4 of 10 sq mm PVC insulated SC unsheathed FRLS copper Conductor of 1100V Grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 10 sqmm copper wire and making good of the concealed portion

Supply and laying of 3 1/2 X 120 sq mm PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good

Supply and clamping of 3 1/2 X 120 sq mm PVC armoured LTUG cable on post or on wall with MS Clamps.

Supply and fixing of brass cable gland for 3 1/2 X 120 sq mm PVC LTUG armoured cable with earth connection

Supply and providing cable end termination of 3 1/2 X 120 sq mm PVC LTUG Aluminum armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and fixing of LT cable route indicator with suitable angle not less than 38mm x 38mm 6mm and 0.6mtr long excavation of earth to a depth of 0.6 mtr and concreting the ground level and making good of the ground as directed by the departmental officers

Earthing as per the ISI specification with an earth electrode of 2.1 mt class 'B' GI pipe of dia not less than 40mm, with copper earth plate of size 125mmx50mmx6mm, with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry

Supply and run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall/floor/ground for earth connection

Supply and run of 1" x 1/8" copper flat (Earth Bus) of 30 cm length on suitable bus insulators with necessary bolt and nuts.

Supply and fixing of 5W LED strip light Fitting (Higher end) complete with PVC unsheathed Copper leads from the terminals to the fittings (5 mtr per each strip)

Supply and fixing of 100W LED flood light fitting (Higher end) complete suitable angle iron frame work on wall / framed stress with unsheathed Cu Leads with MS clamps and aluminium painting complete

Supply and fixing of 63A FP MCB in suitable sheet steel enclosure in flush with wall with earth connection (Higher end)

A) Design, supply, installation, testing and commissioning of 25.0 TR Ceiling suspended nominal capacity factory assembled Air-cooled Condensing unit fixed with energy efficient scroll compressor along with grooved copper tube/aluminium fins air cooled condensor coil with anticorrosion coatings, liquid, accumulator, low noise alumimium propeller condenser fan with Fan motor etc all suitably assembled neatly in heavy duty GSS sheet metal cabinet and duly powder coated as per specification the unit to include built in safety controls like HP/LP switch power quality protector, in built thermal / temperature protection.

Supply, fabrication and erection of fabricated ducting made up of GI sheets of 24 gauge thickness complete with angle flanges, necessary MS angle supports, anchor fasteners, tees and bends wherever necessary etc as required

Supply, fabrication and erection of fabricated ducting made up of GI sheets of 22 gauge thickness complete with angle flanges, necessary MS angle supports, anchor fasteners, tees and bends wherever necessary etc as required

Supplying & Providing thermal insulation for duct of Air-Conditioned area using 19 mm thick non-fibrous, CFC free, closed cell, elastomeric nitrile rubber foamed insulation in pre-formed sheets only with the adhesives supplied by the insulation manufacturer. (The insualtion shall be provided inside Periphery of duct) "Supply and fixing of acoustic insulation 15mm thick with Nitrile rubber Open Cell type inclusive of suitable adhesive for nitrile rubber" (Make: Armaflex / Kflex / Thermobreak / supreme).

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed 9MM cell Nitrile rubber (Class “O”) insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per Specifications

Supply and fixing of extruded aluminium powder coated supply and return air grilles/diffusers with volume control damper.

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories,

22.2 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19mm thick (7/8")

36.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19mm thick

Supply and filling of R410A Refrigerant gas.

Supplying and fixing following sizes of rigid / flexible UPVC drain pipe with suitable clamps etc., for drain water connections from AC indoor units of all types & models upto the location as desired by the Engineer-In-Charge complete with all accessories etc., as required. (a) 40mm dia rigid/ flexible UPVC pipe with nitrile rubber insulation.

Supply, installation, testing and commissioning of duct mounted GI volume control damper

Supply and Run of Control cable between indoor & outdoor communication purpose-Wiring should be insulation on PVC materials as required - 2.5 Sqmm 4 Core Shielded Cable

Supply, Installation and testing of Yamaha System Speaker type 2-way, Bi-amped Powered Speaker, Bass-reflex, Frequency range (-10dB) 52 Hz - 20 kHz, Coverage area H90ﾟx V60ﾟ (Rotatable) Crossover 1.9 kHz: FIR-X tuning™ (linear phase FIR filter) Power rating Dynamic 700 W, Continuous 325 W Dimensions : 305 mm X494 mm X 300 mm, Net weight 15.0 kg

Supply and installation of Digital Signal Processor with two input and six output Feedback Elimination, 2.7 Seconds of Alignment and Zone Delay, RS-232 PC GUI control, Compression and Limiting, Graphic and Parametric EQ Auto-EQ Function, Full Bandpass, Crossover and Routing Configurations, Auto Gain Control, Pink Noise Generator and fulltime RTA Preferred Make : DPA, ATLAS, XTA, MARAN (SOUND PROCESSOR)

Supply and installation of yamaha 16 ch Audio Mixer with FX. SPX algorithm: 24 programs, PARAMETER control:1, FOOT SW:1 (FX RTN CH on/off), Phantom power 48V, Digital I/O, USB Audio Class 2.0 compliant, Sampling Frequency: Max 192 kHz, Bit Depth: 24-bit, USB Audio Class 2.0 compliant, Sampling Frequency: Max 192 kHz, Bit Depth: 24-bit, Input Channels - 12, MIC/LINE - 8, Dimensions :444 mm x 130 mm x 500mm, Nett weighjt 6.8kg

Supply and testing of Shure BLX series Wireless Handheld Mic, table top single-channel receiver, handheld transmitter System: Operating Range:Maximum of 300 ft line of sight, Audio Frequency Response : 50 to 15,000 Hz, Transmitter RF Output Power:10 mW, typical (varies by region) Audio Output Connector:XLR and 1/4" (6.3 mm) unbalanced Maximum Output Level:-27 dBV (XLR, mic level),-13 dBV (1/4")Total Harmonic DistortionRef. ±33 kHz deviation with 1 kHz tone 0.5%, typical,Dimensions : 40 mm X 188 mm X 103 mm H x W x D, Weight 241g

Supply and testing of Shure Beta 58 with metal base amnd short stand for podium Frequency Response : 50 to 15,000 Hz, Transmitter RF Output Power:10 mW,

Supply, Installation and testing of Epson 6000 Lumens laser proejctor, Resolution WUXGA, 1920 x 1200, 16:10 ; Full HD 1080p support, Light Source:Type: Laser Diode Life (Normal / Extended): 20,000 / 30,000 hours, Keystone Correction Manual vertical: ± 30 °, Manual horizontal ± 30 , Contrast Ratio:Over 2,500,000:1, Lens Shift Manual - Vertical ± 50 %, horizontal ± 20 %, dimensions 440 x 304 x 120 mm (Width x Depth x Height), weight 8.5 kg

Supply, Installation of 185" tubuler motorized screen with remote control, Ratio 16:10 Type Elegant Tubular Motor, Fabric Matte White, Viewing Area W x H : 160" x 90"4071 x 2544 (mm)

Supply and installation of 10 Channel Power conditioner with load of 10 Amps with Circuit breaker AC noise filtering to reduce radio frequency and electromagnetic interference (RFI/EMI), Spike & surge protection ensures equipment safe

Supply and installation of 5 KVA stabilizer of Krycard Make

Supply and Installation of Customised Ceiling Mount Brackets for Yamaha speakers.

Supply and Fixing of Customised Ceiling mounting Bracket for projector

Supply and Installation of belden Loud Speaker cables, Neutrik XLR connectors in lumpsum asper the requirement (CABLES AND CONNECTORS)

Supply and Laying of HDMI Sheilded AOC cable 30 Mtr.

Supply and Installation of XLR Wall plate Neutrik XLR connectors with Barn doors.

Supply and installation Floor Mount AV Rack with tray and accessories with power Floor Standing Rack 22U 600X600mm, Static Loading 600 Kgs,19” dimension and Cable entry on Top & Bottom, Front Toughened Glass Door & Back Steel Door with Lock and Keys, Turning angle of front and rear door over 180°, Powder coating Frame.

Calibration and Programming Charges for Yamaha speakers, digital signal processor and audio mixer

Sub switch Panel: Supply and Erection of 400A capacity Dust and Vermin Proof Cubical Panel Board made up of 16 SWG CRCA steel with supply and fixing of the following interior mounting fuse switches with HRC fuses arranged in two Horizontal rows with one switch over the other with a central bus bar chamber and two nos of Horizontal cable chambers at the two ends one on each side next to the fuse switch chamber and confirming to IE rules.

Supply and laying of 2R 3 1/2 X 150 sq mm PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good

Supply and clamping of 2R 3 1/2 X 150 sq mm PVC armoured LTUG cable on post or on wall with MS Clamps

Supply and fixing of brass cable gland for 3 1/2 X 150 sqmm PVC LTUG armoured cable with earth connection

Supply and providing cable end termination of 3 1/2 X 150 sq mm PVC LTUG Aluminum armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Earthing as per the ISI specification with an earth electrode of 2.1 mt class 'B' GI pipe of dia not less than 40mm, with copper earth plate of size 125mmx50mmx6mm, with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry

Supply and run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall/floor/ground for earth connection

Supply and fixing of 25x3mm copper flat with necessary clamp/ supports on wall / floor / ground for earth connection

Fabrication, Errection, Testing and commissioning of pedestal mounted pillar box made out of 16SWG CRCA MS Sheet of size 48”x36”x18” out door Type with double compartment and with angle iron stiffener with front open doors for each compartment with lock and key facilities with sealing (TNEB Type) arrangement with dust and Vermin proof and space for fixing TNEB Electronic type energy meter suitable for 3 phase 415 V 4wire 50 HZ AC supply having 400A Capacity Copper Bus bar on suitable bus insulators and provision for mounting 3 Nos C.T.S of 400/5A for incoming to the energy meter and supply and fixing of 3 Nos.400A fuse Units and neutral link on 6mm Thick Hylum sheet and provision for cable entry for both incoming and outgoing cables at the bottom and painting the board with Two coats of anti-corrosive paint of approved colour with earth connection and comprising the following.

Supply and fixing of 3 Phase 400A aerial fuse units for 3 Nos 400A fuse units (500V) on suitable MS sheet covered with 6mm thick hylem sheet on suitable angle iron work with the tapping pole with necessary clamps.

GST at 18%

Please Enable Macros to View BoQ information