Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | 1₹4.5 LAccepted-Finance 39 39 THANGAMAPURI PATTINAM METTUR DAM 636402 | SALEM | TAMIL NADU | 636402 | 1 | Accepted-Finance satisfied | |
| 2 | 2₹4.9 L+₹39,340 (8.78%)Accepted-Finance 150 1ST STREET THOTTILPATHY SALEM CAMP PO METTUR DAM 636 456 | METTUR DAM | SALEM | TAMIL NADU | 636456 | 2 | Accepted-Finance satisfied |
Tender Value
₹6.0 L
EMD Value
₹6,100
Closing Date
25 Jul 2022, 2:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
CE/MTPS-I
The Chief Engineer Mettur Thermal Power Station-I Mettur Dam- 636406 Salem District
MTPS I CHP I Assistance for carrying out cold vulcanizing belt joint
2022_EB_240437_1
CE SE M II MTPS I CHP I LT 58 2022 2023
Limited
Miscellaneous Works
Works
120 days
MTPS-I
As per Tender Specification
5 documents required · 5 mandatory
₹0
₹6,100
Yes
20 Aug 2022
8 Jul 2022
26 Jul 2022
8 Jul 2022
25 Jul 2022
8 Jul 2022
Amount
For replacement of 1600 mm width conveyor Belt work in tunnel area for conveyor I,II,III & IV. Charges for arranging chain block and belt clamp in conveyor lifting the counter weight box assembly and normalizing the counter weight box assembly after completion of work (5Ton /10 Ton chain block contractor scope)
Charges for removing idler, idler frame, cutting removal of wornout/damaged joint/excess elongation of belt, pulling, positioning the belt ends. Arranging platform. Assistance for making 1 No. cold vulcanizing joint. After completion of work, releasing belt clamp, fixing idlers, idler frame and conduct trial run of the conveyor.
Charges for transporting, positioning new conveyor belt drum. Arranging pulley and rope. Cutting and removal of wornout/damaged belt from conveyor. Releasing the belt from drum. Leading, lifting, laying and tensioning the conveyor belt. Rolling the released wornout damaged belt. Devoluting the belt scrap to Central Stores/MTPS.
For Replacement of 1800 mm width conveyor belt work in tunnel area for belt feeders I,II,III & IV. Charges for dismantling Belt Feeder pulley hood, skirt board, cutting removal of wornout/damaged belt. Removing idler, idler frame. Adjusting the tension screw and position the tail pulley. Cutting removal of 11.5 mtr/12mtr x 1800mm width new conveyor belt from roll, transporting, leading, lowering to Belt Feeder tunnel floor. Removing belt scrap from tunnel area and devoluting to Central Stores/MTPS.
Charges for Laying new belt on Belt Feeder. Clamping the belt. Assistance for making 1 No. cold vulcanizing joint. After completion of work releasing belt clamps fixing idler, idler frames, skirt board, pulley hood etc., adjusting the belt tension and trial run of the Belt Feeder.
Charges for providing 3 Ton chain pulley block, lifting the non-drive pulley along with two piece pillow block. Dismantling the wornout belt-tensioning device – 2 Nos. replacing new / serviced belt tensioning device – 2 Nos. in position and erection of non-drive pulley along with two piece pillow block. Aligning the belt-tensioning device by checking water tube level on the both ends. Tightening the bolts and nuts and removing the chain block.
For Replacement of 2000mm width conveyor belt work in tunnel area for dribble conveyor I,II,III & IV. Charges for removal of skirt board, cutting removal of worn out belt of size 2000mm x 30 mtr from dribble conveyor, leading, lifting the belt scrap from tunnel area to ‘0’ mtr. ground floor and devoluting to central stores/MTPS. From 2000 mm width belt roll cutting removal of 30 mtr belt, leading lowering to the dribble conveyor tunnel working area.
Adjusting the tension screw, position the pulley, laying new conveyor belt of size 2000mm width x 30 mtr length in Dribble Conveyor of Apron Feeder. Clamping the belt. Arranging plat form. Assistance for making 1 No. cold vulcanizing joint. After completion of belt joint removing belt clamp, fixing skirt board, adjusting the tension screw, tensioning the belt and trail run the dribble conveyor.
Charges for decoupling the slow speed coupling from gear box to head pulley and removal of flexible rubber elements and assembling the coupling after completion of belt joint work (damaged flexible rubber element has to be replaced by new one) and all bolts tightening checking etc. including cost of T&P’s and consumables.
Hire charges for steel rope and pulley for Sl.No.3
Hire Charges for T&Ps and charges for consumables for Data Sl.No.1 to 9.
SATHISH ENGINEERING
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .