SPECIAL REPAIRS TO BLDG No. T-1 (MAIN OFFICE) OF GE 872 EWS, SPECIAL REPAIRS TO BLDG No. T-5 OF EME BN AT LIKABALI MIL STN UNDER GE 872 EWS

Amount

B/R SERVICES/WORKS

Demolition Cement Concrete (un-reinforced) of any description in Ground Floors, Pavings, etc. not exc. 150mm thickness (above or below Ground Level) and removing debris, etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Dismantling Posts or Struts (Wood, Steel or RCC) of any Section and embedded in Natural Ground including Taking out embedded Portion and Making Good disturbed Ground, complete all as specified and as directed.

Dismantling Posts or Struts (Wood, Steel or RCC) of any Section and embedded in Concrete, Brick Masorary, etc. including Taking out embedded Portion and Making Good disturbed Ground, complete all as specified and as directed.

Demolition Brick Work or Pre-cast Concrete Block Masonry, built in Cement Mortar and in any Position including all Quoins, Arches and Pillars, etc., complete all as specified and as directed.

Dismantling Timber Scantling 40 Sq Cm and Over in Section in Unframed Work, Segregating the Serviceable Steel Sheeting, stacking properly at Sites and keep in Safe Custody for re-use, complete all as specified and as directed.

Dismantling Timber Fillets, Rails, Posts, Rafters, Purlins, etc. Under 40 Sq Cm in Section in Unframed Work, complete all as specified and as directed. NOTE : Taking down/ out of Forking Pieces fixed with Scantlings, Boarding, Studs, etc. will not be Measured separately for Payment.

Dismantling Boarding of any description and fixed in any Position with Nails, complete all as specified and as directed.

Taking down Chowkat or Frame of any description (without Taking Off Shutter from the Frame) not exc. 1.50 Square Metre Each, complete all as specified and as directed.

Taking down Chowkat or Frame of any description (without Taking Off Shutter from the Frame) exc. 1.50 Square Metre but not exc. 4.00 Square Metre Each, complete all as specified and as directed.

Taking down Shutter of any description, not exc. 1.00 Square Metre Each, complete all as specified and as directed.

Taking down Shutter of any description, exc. 1.00 Square Metre but not exc. 2.00 Square Metre Each, complete all as specified and as directed.

Dismantling Wrought Iron Work of any description, complete all as specified and as directed.

Dismantling Plain or Corrugated Steel Sheeting of any gauge and thickness, Segregating the Serviceable Steel Sheeting, stacking properly at Sites and keep in Safe Custody for re-use, complete all as specified and as directed.

Dismantling Wall and Ceiling Boards (Fibre, Pulp, Insulation, etc.) or Insulation Boards/ Slabs/ Blankets of any descriptions including Cover Fillets, complete all as specified and as as directed.

Dismantling Floor, Hearth or Wall Tiling including Cement Mortar Bedding (but not backing) and removing debris, etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Dismantling Stone Slabs and/or Tiles of any description or thickness in Floors, Aprons, etc. laid, bedded and pointed in Cement Mortar and Removing debris, etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Taking down Cement Plaster including raking out Joints, hacking for Key, scrubbing down with Water and removing Debris, etc. etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Hacking/Taking out Broken Glass of any description from Wooden or Metal Frames, or Stone, Concrete or Brick surrounds of any thickness or size; Hacking out Old Putty or Removing Beads, etc., complete all as specified and as directed,

Taking up or down Steel Tubing 15mm bore (dia) and Connections, segregating the Serviceable Pipes and Connections, stacking properly at Site(s) and keep in Safe Custody for re-use, complete all as specified and as directed.

Taking up or down Steel Tubing 20mm bore (dia) and Connections, segregating the Serviceable Pipes and Connections, stacking properly at Site(s) and keep in Safe Custody for re-use, complete all as specified and as directed.

Taking/ Lowering down Unserviceable Water Storage Tank of any description, exc. 500 Litre and not exc. 1000 Litre Capacity after disconnecting all Water Pipe Line Connections, complete all as specified and as directed.

M&L Cement Concrete 1:4:8 (40mm graded aggregate) in Foundations, Filling and Mass Concrete, etc. including necessary Formwork, complete all as specified and as directed. NOTE : Cost of Formwork shall deem to be included in the Quoted Unit Rate.

M&L Reinforced Cement Concrete 1:2:4 (12.5mm graded stone aggregate) in Columns, Pillars, Posts, Struts, etc., complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (12.5mm graded stone aggregate) in Beams, Cantilevers, Bressumers, Lintels over 1.50 Metre Span, etc., complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Formwork to Sides of Pillars, Posts, Struts, Columns and Stanchions, Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Sides and Soffits of Floor or Roof Beams, Girders, Beam Haunchings, Bress-summers, Lintels, Cantilevers, Shelves including Supports, Overhangs, etc. also splays between Floors and Beams, etc., Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Brick Work with Sub-Class ‘B’ Bricks (Old Size Bricks), Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in Cement Mortar 1:6, complete all as specified and as directed.

M&L Brick Work Half Brick thick with Sub-Class ‘B’ Bricks (Old Size Bricks), Straight or Curved on Plan to any Radius, built in Cement Mortar 1:4, complete all as specified and as directed.

M&L Cutting Holes in Brick Walls, not exc. Half Brick thick, built in Cement Mortar for inserting of Holdfasts, Lugs, etc. and Making Good to dismantled portion with Cement Concrete 1:3:6 (20mm graded stone aggregate) or Cement Mortar 1:3 (as required) and adjoining Surfaces in Cement Mortar 1:4, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) in Scantling, Cleansawn, Timber fixed (Unframed work), fixing with Nails, complete all as specified and as directed.

Refixing only Second Class Hardwood (well seasoned) in Scantling (except Scantlings, Serviceable Timber Scantling obtained from Item No. 1.005 here-in-before), Timber fixed (Unframed work), fixing with Nails, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Fillets, Wrought, Square, Rectangular or Triangular in Section, exc. 13 Sq Cm but not exc, 25 Sq Cm, fixed with Nails, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Plain, Solid, Straight, Chowkats and Frame, Wrought, Framed rebated on the Solid, Rounded or Chamfered, put together with Glue pinned at Joints, complete all as specified and as directed.

M&L Plain Framed Factory Made Panelled Shutter 40mm thick having Two Panels with Second Class Hardwood Lock Rails and Stiles and Panels of 12mm thick BWP Commercial Ply or 12mm thick Veneered Particle Board with Commercial Veneering on both Faces, size of Rail and Stile as per IS : 1003 (Part I), Kiln Seasoned and Chemically Pressure treated and fitted to Chowkat, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Glazed and Skeleton Shutter 35mm thick, Open rebated and prepared to receive Glass, Gauze, etc. (Without Sash Bars), Edges of Framing plain, chamfered or rounded. fitted with cut and mitred Beads for securing glass, etc.; sizes of Members of Shutters as specified in SSR Part I, Section 8, Clause 8.24(a) and fitted to Chowkat, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Glazed and Skeleton Shutter 30mm thick, Open rebated and prepared to receive Glass, Gauze, etc. (Without Sash Bars), Edges of Framing plain, chamfered or rounded. fitted with cut and mitred Beads for securing glass, etc.; sizes of Members of Shutters as specified in SSR Part I, Section 8, Clause 8.24(a) and fitted to Chowkat, complete all as specified and as directed.

S&F Factory made Solid PVC Door Frame of size 50x47mm made out of 5.0mm thick Plain Colour (Ivory Shade) PVC Sheet reinforced with Mild Steel Square Tube and fixing in opening as per Specification and Drawing of MES Schedule Part-II, complete all as specified and as directed.

M&L Factory Made Solid Panel PVC Door Shutter 30mm thick (Style) Plain colour (Ivory shade) consisting of Frame made out of Mild Steel Tubes for Top and Bottom Rails, Mild Steel Frame shall be covered with heat moulded wood grain PVC ‘C’ Channel having a PVC Sheet Strip of 20mm width stuck inside with Solvent Cement for Stiles and wood grain PVC Sheets for Top Rail, Lock Rail & Bottom Rail on either side and as gap insert for Top Rail & Bottom Rail, Panelling of wood grain PVC Sheet to be fitted in the Mild Steel Frame welded/sealed to the Stiles and Rails with suitable 5mm thick x 15mm wide PVC Sheet beading used inside Stiles and Rails and decorative PVC Beading of 10mmx10mm (90) and jointed together with Solvent Cement and fixing in the Frame at Site, complete all as specified and as directed.

M&L Anodised Aluminium Powder Coated (Thickness of Powder Coating not less than 50 micron) Frame for Doors, Windows, Ventilators with One or More Rebates including Joining Cleat for fixing, etc., complete all as specified and as directed.

M&L Anodised Aluminium Powder Coated (Thickness of Powder Coating not less than 50 micron) Door Shutters, Aluminium Section weighing not less than 0.55 KG/RM including necessary Joining Cleats, Glazing Clips, Rubber/ Neoprene Packing, Handles (as approved) - 2 No. in Each Door, Stainless Steel Hinges of size as ordered, anodised Aluminium Snap Beading, Screws, etc, complete all as specified and as directed.

M&L Powder coated anodized Aluminum Door Single or Double Leaf Shutters, Mortice Lock Frame with One or More Rebates including Jointing Cleats and Aluminium Door Shutter Side Hung type without Sash Bars including Jointing Cleats, Glazing Clips, Rubber Packing, anodized Aluminium Snap Beading, Screws and Half Portion of Shutter with 5.0mm thick Plain Glass and Other Half Portion with 12mm thick Both side Prelaminated Particle Board, complete all as specified and as directed. Aluminium Sections shall be conform to Catelogue of Make : 'JINDAL' or Equivalent Make (as approved by GE) are as under :- (a) Rectangular Tube - 14005 (b) Shutter Vertical - 19501 (c) Shutter Top Rail - 19503 (d) Shutter Middle Rail - 20060 (e) Shutter Bottom - 19511 (f) Glazing Clip - 19352

M&L Powder coated anodized Aluminium Window Frame 3 Track Channel with Double Sliding Shutters, One with 5.0mm thick Plain Glass and Other with 0.36mm nominal dia of Stainless Steel Wire and average aperture 1.4mm fixed including Jointing Cleats, Glazing Clips, Rubber Packing, andozied Aluminium Snap Beading, Screws and suitable Aluminium Fittings such as suitable size Aluminium Handle, Aluminium Hinges, etc., complete all as specified and as directed. Aluminium Sections shall be conform to Catelogue of Make : 'JINDAL' or Equivalent Make (as approved by GE) are as under :- (a) Bottom Frame Rail - 20620 (b) Top Frame & Vertical - 20621 (c) Handle Side - 20606 (d) Shutter Inter Lock - 20724 (e) Shutter Top & Bottom - 20844 (f) Glazing Clip - 19352

S&F Anodised Aluminium Ventilator Lever type with Locking Arrangment, Moving up and down with Frame of Aluminium Section weighing 0.55 KG/RM including necessary Jointing Cleats, Glazing Clips, 4.0mm thick Frosted Glass of 10mm Wide, Rubber Packing, anodised Aluminium Snap Beading, Screws, etc., completed all as specified and as directed.

S&F Aluminium anodised Barrel Tower Bolt of size 125mm long (as approved), Extruded Section, complete all as specified and as directed.

S&F Aluminium anodised Barrel Tower Bolt of size 150mm long (as approved), Extruded Section, complete all as specified and as directed.

S&F Aluminium alloy, anodised, Sliding Door Bolt 300mm long (as approved) with Hasp, Staple (Bolt type) and Fixing Clips of Sheet, Cast or Extruded Sections and Fixing Bolts and Sliding Bolts of Extruded Sections or Cast-Aluminium alloy and fixed, complete all as specified and as directed.

S&F Stainless Steel Butt Hinge of size 75mm (as approved), complete all as specified and as directed.

S&F Stainless Steel Butt Hinge of size 100mm (as approved), complete all as specified and as directed.

S&F Mild Steel Continuous (Piano) Hinge, 30mm Width of Flaps (when Open) with Bright Finish or Electrogalvanised and Fixing-in-repairs, complete all as specified and as directed.

S&F Aluminium Handle of size 125mm (as approved), anodised, Cast type, complete all as specified and as directed.

S&F Aluminium Handle of size 125mm (as approved), anodised, Cast type, complete all as specified and as directed.

S&F Floor Door Stopper (as approved) with Overall length of Cover Plate 150mm of Aluminium Alloy Body and Tongue (as approved) anodised, with Hard Drawn Steel Spring, fixed in Floor, complete all as specified and as directed

S&F Door Closer Aluminium alloy (Extruded Section) Body, Hydraulically Regulated, Designation No. 3, Universal type (as approved), suitable for Door Shutters of 851mm to 1000mm in Width and of Weight between 61.00 to 80.00 KG and Fixing-in-repairs, complete all as specified and as directed.

S&F Mild Steel 300mm, Ordinary Rat Tail Rod Pattern Springs (as approved), including Roller and Roller Plate and Fixing-in-repairs, complete all as specified and as directed.

S&F Brass Mortice Lock, Vertical type of size 100mm, 4 Levers (as approved) and Fixing-in-repairs, complete all as specified and as directed.

S&F Brass Solid Body Hat and Coat Hooks, 175mm to 250mm (as approved) and Fixing-in-repairs, complete all as specified and as directed.

S&F Stainless Steel Drapery Rods (Curtain/Harrison Rails) having 24mm Outer dia and 1.0mm Wall Thickness (minimum), fixing with and including Brackets, Stops, Rollers, Side Holders, etc, and Fixed-in-repairs, complete all as specified and as directed.

S&F Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples, complete all as specified and as directed.

S&F Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples and Fixing-in-repairs, complete all as specified and as directed.

S&F Sheet Glass 3.0mm thick, Plain, Ordinary quality and Glazing with Oil Putty in Square not exc. 0.50 Sqm in Each Pane, complete all as specified and as directed.

S&F Sheet Glass 5.5mm thick, Plain, Ordinary quality and Glazing with Oil Putty in Square, exc. 0.50 Sqm in Each Pane, complete all as specified and as directed.

M&L TMT Bars 10mm dia and Over, cut to length, bent to shape required including cranking, bending spirally for hooping for Columns, hooking Ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L TMT Bars 8.0mm dia in Stirrups, Spacers and Binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L Mild Steel Bands, Straps, Supports or Stays for Rainwater, Ventilating Pipes including Bolts, Hooks (Stay) for large Gates; Hook and Pintle Hinges: large Hasps and Staples; Hand Made Sliding Bolts; Clamps; Holdfasts; Wall Ties and similar small Articles conforming to Fe-290 Gde-E-165, complete all as specified and as as directed.

M&L Mild Steel Framed Works such as Grills, Gratings, etc. with Ends of Bars shouldered and/or riveted or forged into Spikes; Framed Guard Bars; Barred Iron Doors; Ladders; Framed Balusters; Walkways; Railings; Framework of Water Tanks and similar Work, conforming to Fe-290, Gde-E-165, complete all as specified and as directed.

M&L Rolled Mild Steel in Joist, Channel, Angle, or Tee Sections in Vertical Post, conforming to Fe-410-W (Gde E-250) Quality 'B', fixed independently, without Connecting Plates, etc. (cut to ordinary lengths i.e. within 20mm of the Length indicated), complete all as specified and as directed.

M&L Rolled Mild Steel Sections in Main and Cross Beams, Hip & Jack Rafters, Purlins where connected to Common Rafters, Running Rails and Guides for Sliding Doors, conforming to Fe-410-W (Gde E-250), Quality 'A', fixed with Angle Cleats or other Connecting Plates, complete all as specified and as directed

M&L Rolled Mild Steel Sections in Roof Trusses (Framed), Trussed, Purlins, Crane Gantries, Rails and Fastenings and Heavy Bracket Framing (Beam, Tee, Angle, Channel or Flat Sections) including Distance Pieces, Cleats, etc., conforming to Fe-410-W (Gde E-250), Quality 'A', complete all as specified and as directed.

M&L Mild Steel Screw Bolts (machine made) with Hexagonal or Square Heads at One End and screwed the Other, or screwed Both Ends, Each screwed End to be fitted with Washers and One Hexagonal or Square Nut, Length of Bolt exc 5.0 Cm but not exc. 10 Cm Long, Diameter of Neck 5.0mm to 10mm, complete all as specified and as directed.

S&F Corrugated Mild Steel Sheeting 0.63mm thick, Galvanised @120 Gram Per Sqm, with Two Corrugation Side Lap, fixing with and including L-type or J-type Cranked Hook Bolts with Washer, etc., complete all as specified and as directed.

M&L Refixing Galvanised Corrugated Mild Steel Sheeting 0.63mm thick (Serviceable Steel Sheets obtained from Item No. 1.013 here-in-before) with Two Corrugation Side Lap, fixing with and including L-type or J-type Cranked Hook Bolts with Washer, etc., complete all as specified and as directed.

S&F Plain Mild Steel Sheeting 0.80mm thick, Galvanised @ 120 Gram Per Sqm, in Ridges, Hips, Valley Gutters, etc., fixing with and including L-type or J-type Cranked Hook Bolts with Washer, etc., complete all as specified and as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Corrugated Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Plain Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Ridges/ Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

M&L Exposed Suspended False Ceiling System having GI Snap Grid/ Frame Work of size 605x605mm with and including Hangers 4.0mm dia GI (upto 1200mm length) for adjusting Level, fixed to Roof Slabs by means of Ceilling Cleats made out of GI Flat 40x3.0mm in size, 60mm long and Expansion Hold Fasteners 12.5mm dia, 40mm long, complete all as specified and as directed.

S&F HSPC Non-Asbestos Fibre Cement Building Boards 4.0mm thick, Pre-primed, Self Embossed, Textured Designer Boards, Water Resistant, Termite Resistant, Fire Resistant for insulation, fixed or laid/ inserted to Snap Grid Frame Work with Screws, complete all as specified and as directed.

S&F Prelaminated Particle Board 18mm thick, Interior grade, Prelaminated One Side with Decorative Choice Lamination and Other Side Balancing White Lami-nation, fixed with Screws to Timber Frame Work, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (20mm graded stone aggregate) 40mm thick as Flooring, etc., Laid in Alternate Panels, finished Concrete Surfaces Even and Smoooth without Using Extra Cement, complete all as specified and as directed.

M&L Glass Dividing Strips 38mm Wide and 3.0mm thick and inserted in Position, conform to Design, complete all as specified and as directed.

M&L Non-skid Ceramic Coloured/Designer Tiles (1st quality and/or as approved), 7.0mm to 8.0mm thick (Square/ Rectangular), Area of Each Tile exc. 0.11 Sqm but not exc. 0.18 Sqm, in Floors, Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, laid over and including Cement Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Non-skid Ceramic Coloured/Designer Tiles (1st quality and/or as approved), 7.0mm to 8.0mm thick (Square/ Rectangular), Area of Each Tile exc. 0.18 Sqm but not exc. 0.38 Sqm, in Floors, Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, laid over and including Cement Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Glazed Ceramic Coloured Tiles 350x250x7.0mm or 450x350x7.0mm thick (1st quality and/or as approved) in Vertical Surfaces i.e. Dado, Skirting, etc., Set in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, fixing over and including Cement Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Machine cut Granite (of any type) Tiles 20mm thick, Bedded and Jointed with Grey Cement Slurry and Pointed with White Cement with Admixture of Pigment to match the Shade of Granite Stone including Grinding and Polishing, fixing over and including Cement Screed Bed 15mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate

M&L Cement Concrete 1:4:8 (40mm graded stone aggregate) 75mm thick in Sub-base to Paver Blocks in Floors, etc., complete all as specified and as directed.

M&L Rubber Moulded Coloured Glossy Finished Machine Pressed Pre-cast Concrete Interlocking Paver Block 60mm thick of M-35 Grade, with Grey Cement and Pigment of any Shape and Size (as ordered), conforming IS-15658-2006, ISI Marked, laid Dry over and including Sand Cushioning of 50mm thick and grouted with Clean dry Sand as in Floors, complete all as specified and as directed. NOTE : Cost of Sand will deemed to be included in the Quoted Unit Rate.

M&L Cement Concrete 1:3:6 (40mm graded stone aggregate) 75mm thick in Plinth Protection, etc., Laid in Alternate Panels, finished Concrete Surfaces Even and Smoooth without using Extra Cement, complete all as specified and as directed.

M&L Rendering (Internal) 10mm thick in Cement Mortar 1:6 on Brick/ PCC Blocks or Concrete Works, finished Plastered Surfaces Even and Smooth without using Extra Cement, complete all as specified and as directed.

M&L Rendering 15mm thick in Cement Mortar on Brick/PCC Blocks or Concrete works consisting in 2 layers, Backing/Under layer of 10mm thick and Float/ Top layer 5.0mm thick including mixeing WPC to Float/ Top layer, finished Fair and Even, complete all as specified and as directed. NOTE : Water Proofing Compound (WPC) will be Measured and Paid saperately under appropriate Item,

Supply only Water Proofing Compound (as approved), conforming to IS:2645-2003, complete all as specified and as directed.

M&L Preparing Surfaces by Complete Removal of Existing Surfaces Treatment on Walls and applying Two Coats of White Wash, complete all as specified and as directed.

M&L Preparing New Plastered Surfaces of Walls and applying a Layer of Wall Care Putty 3.0mm thick on Plastered Surfaces of Walls including Cutting and Rubbing down to obtain a Even and Smooth Surface and applying Two Coats of Distemper Oil Emulsion, Premium quality (of approved Tint) on Putty Finished Surfaces, complete all as specified and as directed.

M&L Preparing Old Plastered Surfaces by Complete Removal of Existing Surfaces Treatment on Walls and applying a Layer of Wall Care Putty 3.0mm thick on Plastered Surfaces of Walls including Cutting and Rubbing down to obtain a Even and Smooth Surface and applying Two Coats of Distemper Oil Emulsion (of approved Tint) on Putty Finished Surfaces, complete all as specified and as directed.

M&L Preparing Newly Plastered Surfaces of Walls and applying Two Coats of Cement Based Paint (of approved Tint) over a coat of Alkali Resistant Priming Paint, complete all as specified and as directed.

M&L Preparing Old Treated Surfaces on Walls and applying One Coat of Cement Based Paint (of approved Tint), complete all as specified and as directed.

M&L Preparing Old Plastered Surfaces by Complete Removal of Existing Surfaces Treatment on Walls and applying a Coat of Chalk Whiting (as Preparatory Treatment to obtain a Fair and Even Surfaces) and applying Two Coats of Weather Coat Exterior Paint (of approved Tint) over a Coat of Primer (as per Manufacturer's instructions), complete all as specified and as directed.

M&L Preparing New Wooden Surfaces of any description, over 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint) over a Coat of Pink Primer, complete all as specified and as directed.

M&L Preparing Old Painted Wooden Surfaces of any description, over 10 Cm in Width or Girth and applying One Coat of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint), complete all as specified and as directed.

M&L Preparing New Wooden Surfaces of any description, not exc. 10 Cm in Width or Girth when unconnected with other Painting or when Painted in different Tint and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint) over a Coat of Pink Primer, complete all as specified and as directed.

M&L Preparing Steel and Iron Surfaces of any descriptions, over exc. 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint) over a Coat of Red Oxide Zinc Chrome Primer, complete all as specified and as directed.

M&L Preparing New or Previously Treated Surface of Wood and Wood based Materials of any description and girth and treated with Two Coats of Creosote Oil, complete all as specified and as directed.

M&L Preparing previously Untreated Surfaces of Wood and Wood Based Materials, of any description and girth not otherwise described and treating with Tar or Coal Tar Black Paint to Backs of Chowkats, etc. Area tarred exc. 0.10 Sqm but not exc. 0.50 Sqm Each including Sanding with Clean Sharp Sand after tarred, complete all as specified and as directed.

M&L Preparing previously Untreated Surfaces of any description and girth not otherwise described and treating with Tar or Coal Tar Black Paint to Holdfast or similar Small Items, Area tarred not exc. 0.10 Sqm Each including Sanding with Clean Sharp Sand after tarred, complete all as specified and as directed.

Supply & laying Steel Water Tubing 15mm bore (dia), Galvanised, ‘medium grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other situation, complete as all specified and as directed.

M&L Refixing old Steel Tubing 15mm bore (dia) and Connections (Serviceable Pipes and Connections obtained from Item No. 1.019 here-in-before) in new or old position (Walls, Ceiling, Floors, etc.) including cleaning both inner and outer surfaces of Pipes by using Wire Brush including provision of New GI Fittings/ Connections (as required at Sites), complete all as specified and as directed.

Supply & laying Steel Water Tubing 20mm bore (dia), Galvanised, ‘medium grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other situation, complete as all specified and as directed.

M&L Refixing old Steel Tubing 15mm bore (dia) and Connections (Serviceable Pipes and Connections obtained from Item No. 1.020 here-in-before) in new or old position (Walls, Ceiling, Floors, etc.) including cleaning both inner and outer surfaces of Pipes by using Wire Brush including provision of New GI Fittings/ Connections (as required at Sites), complete all as specified and as directed.

S&F Bib Tap 15mm bore (dia), Cast Copper alloy, Chromium plated, screwed down, high pressure, with Crutch or Butter-fly handle, screwed both Ends for Iron Pipe or for Unions and Fixed-in-repairs, complete all as specified and as directed.

S&F Pillar Tap 15mm bore (dia), Cast Copper alloy with Capstan Heads, screwed down, high pressure, with or without lettered 'Hot' or 'Cold' with long screwed Shanks and Fly-nuts, screwed for Iron Pipe and Fixed-in-repairs, complete all as specified and as directed.

S&F Stop Valve 15mm bore (dia), Cast Copper alloy, Chromium Plated, screwed down, high pressure, with Crutch or Butter-fly Handle, screwed both Ends for Iron Pipe or for Unions and Fixed-in-repairs, complete all as specified and as directed.

S&F Gun Metal Globe/Gate Valve 20mm bore (dia) with Iron Wheel Head, screwed both Ends for Iron Pipe and Fixed-in-repairs, complete all as specified and as directed.

M&L Rotational Moulded Polyethene Water Storage Tank 1000 Litre Capacity, Cylindrical, Vertical with Closed Top, 3 layered, conforming to IS:12701-1996, hoisted and fixed in Position all as specified in MES Schedule and Providing all Water Pipe Lines Connections, complete all as specified and as directed.

S&F PTMT Ball Valve 20mm bore (dia), having weight not less than 210 Grams, high pressure with Epoxy coated Aluminium Rod and high density Plastic Ball, screwed for Iron Pipe, complete all as specified and as directed.

S&F Vitreous China White Wash Down Water Closet Pan (Pedestal Pattern) with PVC (SWR) ‘P’ or ‘S’ Trap and Fixing Bolts and Making Good to Floor/ Distrubed Surfaces in Cement Mortar 1:3 and and Fixed-in-repairs, complete all as specified and as directed.

S&F White Plastic Water Closet Seat and Cover for Water Closet Pan (Pedestal Pattern), Closed Pattern with Flat bottom and Cover and Mild Steel Chromium plated or Aluminised Hinging Device and Fixed-in-repairs, complete all as specified and as directed.

S&F Jet Spray System, Brass Chromium Plated (as approved) and suitable for Wash Down Water Closet Pan (Pedestal Pattern) and Fixed-in-repairs, complete all as specified and as directed.

S&F Health Faucet (Hand Spray), Brass Chromium Plated having 1.00 Metre long with Flexible Hose Pipe with hanging Gadget for fixing to Walls and Fixed-in-repairs, complete all as specified and as directed.

S&F Toitet Paper Holder of size 100mm (as approved), Brass Chromium Plated with Cover and Fixed-in-repairs, complete all as specified and as directed.

S&F PVC Flushing Cistern 10 Litre capacity White, Low Level, Valveless, Syphonic Action type with Inlet, Ball Valve, Float and Handle, and PVC Flush Pipe 32mm bore (dia), a pair of Cast Iron Brackets Erecting Stand duly painted including cutting and pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 and Fixed-in-repairs, complete all as specified and as directed

S&F Vitreous China White Wash Hand Basin of Size 550x420mm in Oval Shape including Brass Chromium Plated Waste Fitting 32mm bore (dia) and PVC Waste Pipe 32mm bore (dia) including a Pair of Cast Iron Brackets Brackets Erecting Stand duly painted including cutting and pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 and Fixed-in-repairs, complete all as specified and as directed.

S&F Kitchen or Laboratory Sink made of Stainless Steel l.0mm thick of Overall size 950x510mm and Bowl size 410x330x160mm with Stainless Steel Waste Fitting 40mm (dia), Strainer, Washers and Wastes, etc. including bedding in Cement Mortar to dwarf Wall or including fixing Cantilever Brackets and connecting Union to Pipes and Fixed-in-repairs, complete all as specified and as directed.

S&F Low Density Polyethylene Pipes (LDPE) 32mm bore (dia) of Pressure ratings 6.0 Kg/Sq Cm and fixing to Walls, Ceiling or in Floors, etc. and Fixed-in-repairs, complete all as specified and as directed.

S&F Stainless Steel Kitchen Plate Rack of size 910x760x250mm, Weight not less than 8.70 KG, Moulded Finish, fixed on Walls with Rawl Plug and Brass Screws and Fixed-in-repairs, complete all as specified and as directed. MAKE : HINDUSTAN or Equivalent Make (as approved by GE)

S&F PVC Connection Pipe 15mm in size and 450mm in length with PTMT Nuts and Fixed-in-repairs, complete all as specified and as directed.

S&F Shower Rose 125mm dia, Brass Chromium Plated with Shower Arm and Swival Joint including fixing to Steel Pipe and Fixed-in-repairs, complete all as specified and as directed.

S&F Wall Mixer 15mm bore (dia), Brass Chromium Plated, for mixing 'Hot' & 'Cold' Water, screwed down, screwed both Ends for Iron Pipe or for Unions and Fixed-in-repairs, complete all as specified and as directed.

S&F Stainless Steel Soap Dish, not less than 125mm in size (as approved), fixing to Walls with and including Chromium plated Brass Screws and Wooden/ Plastic Cleats and Fixed-in-repairs, complete all as specified and as directed.

S&F Tubular Towel Rail 20mm dia, Brass Chromium Plated, D-type, 60 Cm long between Flanges with Bracket (One Pair), fixed on Wall with Wooden/ PVC Cleats and Brass Chromoum Plated Screws and Fixed-in-repairs, complete all as specified and as directed.

S&F Chromium Plated Grating Doom 100mm dia with Waste Holes (as approved) and Fixed-in-repairs, complete all as specified and as directed.

M&L PVC (SWR) Floor Trap having Diameter of Outlet in 100mm, Plain with Grating including Jointing with Solvent Cement and Fixed-in-repairs, complete all as specified and as directed.

S&F PVC (SWR) 75mm bore (dia) Pipe, Single Socketed, in any length with Rubber Ring Joints, fixed to Walls or in Floors and Fixed-in-repairs, complete all as specified and as directed.

S&F PVC (SWR) Bend 75mm bore (dia), any radius with Access Door, etc. and jointing with Solvent Cement and Fixed-in-repairs, complete all as specified and as directed.

S&F PVC (SWR) 110mm bore (dia) Pipe, Single Socketed, in any length with Rubber Ring Joints, fixed to Walls or in Floors and Fixed-in-repairs, complete all as specified and as directed.

S&F PVC (SWR) Bend 110mm bore (dia), any radius with Access Door, etc. and jointing with Solvent Cement and Fixed-in-repairs, complete all as specified and as directed.

E/M SERVICES/WORKS

M&L Taking down carefully Copper/Aluminium Point Wiring (Light, Fan, Socket or Power) complete from in any Position including Fixture and Fittings such as Switches, Ceiling Roses, Pendants, Regulators, Sockets but excluding Light Fittings of any description, Making Good Disturbed Surfaces of Walls/ Ceillings, etc. in Cement Mortar 1:3 including providing Surface Treatment (White/ Colour Washing, Distempering, Painting, etc.) wherever required to match the Existing Finishes, complete all as specified and as directed.

M&L Taking down unserviceable Sub-main Wiring from Batten/ Conduit/ PVC Casing Capping of any description, Making Good disturbed surfaces of Walls/ Ceillings, etc. in Cement Mortar 1:3 including providing Surface Treatment (White/Colour Washing, Distempering, Painting, etc.) wherever required to match the Existing Finishes, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH multi-stranded single core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE LIGHT/ FAN/ BELL POINT controlled by One 1-way Switch 6 Amp, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH multi-stranded single core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire for ONE 3/5 PIN SOCKET 6 AMP POINT on SAME BOARD, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH multi-stranded single core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 3/5 PIN SOCKET OUTLET 6 AMP POINT on INDEPENDENT BOARD, complete all as specified and as directed.

M&L Point Wiring with 2.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH multi-stranded single core Copper Conductor Cable with 2.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 3/5 PIN SOCKET OUTLET 6/16 AMP POINT on INDEPENDENT BOARD, complete all as specified and as directed.

M&L Sub-main Wiring with 2-Runs of 6.0 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLSH multi-stranded Single Core Copper Conductor Cable and 1-Run of 4.0 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLSH multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuty Conductor drawn through and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc., complete all as specified and as directed. NOTE :- (a) Cost of 3-Runs of Cables & 1-Run of PVC Casing Capping shall deem to be include in the Quoted Unit Rate and the same will be Mesured as ONE UNIT (b) Sub-main Wiring will be measured PVC Conduit only. Wires required for looping, etc. as ordered will deem to be include in the Quoted Unit Rate.

S&F PVC Block/ Board Closed Recessed of size 100x100x50mm deep with 3.0mm thick Plastic Laminated Sheet Cover including Taking down/ out unserviceable Block/ Board of any description, complete all as specified and as directed.

S&F Switch Piano 6 Amp, Single Pole, Flush type, 1-way, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Socket Outlet 6 Amp, 3 Pin, 2-in-1, Flush type, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Switch Socket Combination 6 Amp, 5 Pin, 2-in-1, Flush type, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Switch Socket Combination 6/16 Amp, 3 Pin, 2-in-1, Multi Plug, Flush type, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Lamp/ Angle Holder PVC/ Polycarbonate type with Back Plate suitable for Batten Fitting and connecting up, complete all as specified and as directed.

S&F Ceiling Rose 65x50mm, 3 Terminals, Surface Bakelite suitable for 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Ceiling Fan Regulator, Electronic, Stepped type, 230 Volt AC including necessary Connection and connecting up, complete all as specified and as directed.

S&F Decorative Wall Light Fixture made of Polycarbonate suitable for 10 Watt LED Bulb and connecting up including Taking down unserviceable Lamp of any description, complete all as specified and as directed. MAKE : BAJAJ/ CG/ HAVELLS/ PHILIPS (as approved by GE).

S&F LED Bulk Head e-TATRA Series Light Fitting 1x6.0 Watt having Plastic Housing with Clear Prismatic Diffuser LED 6.0 Watt Lamp and connecting up with and including suitable size Twisted Flexible Copper Conductor Cable including Taking down unserviceable Light Fitting of any description, complete all as specified and as directed. MAKE : C&S E-TARTA Series 6W or equivalent Model in Make : BAJAJ/ CG/ HAVELLS/ PHILIPS (as approved by GE).

S&F Octane LED Panel Squre 18 Watt Lighting Fixture 18 Watt LED 6500K, connecting up with and including suitable size Twisted Flexible Copper Conductor Cable from Ceiling Rose to Light Fitting including Taking down /out Unserviceable Light Fitting of any description, complete all as specified and as directed. MAKE : HAVELLS, OCTANE LED PANEL SQUARE 18W or equivalent Model in Make : BAJAJ/ CG/ C&S/ PHILIPS (as approved by GE).

S&F LED Integrated Batten T-5 Tube Light Fitting 1x20 Watt with LED 20 Watt and connecting up with and including suitable size Twisted Flexible Copper Conductor Cable including Taking down unserviceable Light Fitting of any description, complete all as specified and as directed. MAKE : HAVELLS E-LITE PRIDE PLUS 20W or equivalent Model in Make : BAJAJ/ CG/ C&S/ PHILIPS (as approved by GE).

M&L Taking down Ceiling Fan of any Make/Model/Sweep from any Height after disconnecting Electric Connection, dismantling Fan Blades and Keep in Safe Custody for Re-hanging/ Re-fixing, complete all as specified and as directed.

M&L Hanging/Fixing only Ceiling Fan (obtained from Item No. 2.020 here-in-before) and connecting with and including suitable size Copper Conductor Cable from Ceiling Rose to Connector of the Fan, complete all as specified and as directed.

S&F MCB Single Pole 6 Amp to 32 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt and connecting up including Taking down/out unserviceable MCB, complete all as specified and as directed.

S&F MCB Single Pole & Neutral 40 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt and connecting up including Taking down/out unserviceable MCB, complete all as specified and as directed.

S&F MCB Distribution Board SPN, 8-way, 240 Volt AC, Single Door, with Steel Phosphotised Powder painted, having 200 Amp rated Neutral Bars & Earth Bar and connecting up including Taking down/out unserviceable MCB DB, complete all as specified and as directed. MAKE : HAVELLS, Cat No. DHDPSHOSRW08 or equivalent Model in Make : LEGRAND/ L&T/ SCHNEIDER (as approved by GE)

Supply & Laying or Passing through Pipe 1100 Volt grade heavy duty, Cross-sectional area 10 Sqmm, 2 Core, Flat or Circular Cable with PVC insulated Aluminium Conductor served with an inner sheathing of PVC Tape armoured with Galvanised Steel Wire or Tape and Overall PVC sheathed in Service Connection suspended by insulating Hangers not more than 1.0 Metre apart including 4.0mm Suspension Wire including Taking down/ out Unserviceable Service Connection, complete all as specified and as directed.

M&L Earthing with Galvanised Earth Plate Electrode 600x600x6.0mm thick, buried directly in Ground vertically to a depth not less than 2.25 Metre below Ground Level with Top Edge of Earth Plate at depth not less than 1.50 Metre below normal Ground Level, connected to Galvanised Earth Lead Wire 4.0mm dia by means of Bolts, Nuts, Check, Nuts and Washers of Galvanised Iron or Steel and Earth Wire protected with and including GI Pipe 15mm bore (dia) Light grade, connected to Test Point upto 7.50 Metre away from Earth Electrode situated, Earth Plate surrounded by a packed thickness of Char Coal or Coke Dust mixed with Common Salt in alternate layers of not exc.150mm thick, PCC Pit in Cement Concrete 1:3:6 (20mm graded stone aggregate) and Pre-cast RCC Cover Slab of size 350x350x50mm in Cement Concrete 1:2:4 (20mm graded stone aggregate), reinforced with 10mm dia TMT Bars @ 100mm Centre to Centre in both ways, GI Wire Mesh, PGI Funnel with GI Watering Pipe 20mm bore (dia) Medium grade including necessary Excavation in Soft/ Loose Soil, Returning, Filling in and Removal of surplus Spoil upto a distance of 50.00 Metre and all as shown in Electrical Plate No. 3 of MES Schedule Part-I and Testing including Taking down/out unserviceable Earthing of any description, complete all as specified and as directed.

RAJIB GOSWAMI ENTERPRISE

Ajinkya Constructions

SURAJIT GOGOI

M/S FRONTIER CONSORTIUM