SPECIAL REPAIR TO BLDG NO P-47 OF ECHS POLYCLINIC DUNDAHERA ARMY CAMP, GURGAON UNDER AGE B/R (P) MANEKSHAW CENTRE AND AGE E/M OF GE (SOUTH) DELHI CANTT-10

Amount

Roughening surfaces of old concrete floor/wall by picking, sweeping clean and washing down with water to remove dust, etc and brushing and applying neat cement slurry with 3.0 Kg of cement per sq metre complete all as specified and as directed.

M&L for vitrified tiles 10 mm thick (square/rectangular) polished, area of each tile not exceeding 0.36 sqm, as in floors laid over and including 15mm thick cement screed bed in CM 1:6 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for vitrified tiles 10 mm thick (square/rectangular) polished, area of each tile not exceeding 0.36 sqm, as in skirting laid over and including 10mm thick cement plaster as backing layer in CM 1: 4 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L for non-skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors laid over and includIng 15mm thick cement screed bed in CM 1:6 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for joint free glazed ceramic coloured tiles in vertical surface 450x300x7 mm thick laid over and including 10 mm thick cement plaster as backing layer in CM 1:4 set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and as directed.

Demolition of brick work built in cement mortar or cement lime mortar complete all as specified and as directed.

M&L brick work with sub class `B' bricks straight or curved on plan exc. 6mtr mean radius built in cement mortor 1:6 complete all as specified and as directed.

Taking up or down steel tubing and connections including cleaning for re-fixing, 15 mm bore of pipe complete all as specified and as directed.

All as per Srl item No.09 above but 20 mm bore of pipe complete all as specified and as directed.

S&F 15 mm bore GI tubes, medium grade galvanised, with all fittings and fixed complete to walls and ceilings or laid floors or concealed complete all as specified and as directed.

All as per Srl item No.11 above but 20 mm bore of pipe complete all as specified and as directed.

Cutting chases or making holes, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and as directed.

Dismantling water tanks of capacity exceeding 1000 litres but not exceeding 2000 litres, complete all as specified and as directed.

S&F 2000 ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and as directed.

S&F ball brass valves, high pressure, with of PTMT with epoxy coated aluminium rod & high desity plastic ball ascrewed for iron pipe of 20mm bore and fixed complete all as specified and as directed.

S&F in repairs gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe 20 mm bore complete all as specified and as directed.

S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white in colour including sheet cover of closed pattern with flat bottom and mild steel chromium plated or aluminiumised hinging device complete all as specified and as directed.

S&F in repairs, PVC valveless, syphonic action type flushing cisterns 10 ltrs capacity, low level, white, with inlet ball valves, float and handle including brackets and pvc flush pipe 32 mm dia for low level complete all as specified and as directed.

S&F in repairs vitreous china wash basin, white, angle back, size 400 x 400mm, including necessary waste pipe and coupling, brackets and cutting for and pinning in ends of brackets complete all as specified and as directed.

S&F PVC connections 450mm long with brass unions at both ends suitable for 15mm bore pipe complete all as specified and as directed.

S&F in repairs 15 mm angle valve/ stop valves, cast copper alloy , chromium palted, fancy type screwed down high pressure with crutch and butter fly handles , screwed with iron pipes or for union complete all as specified and as directed.

S&F in repairs bib tap (quarter turn), brass chromium plated fancy type, long body with flange screwed down, screwed for iron pipe 15 mm bore complete all as specified and as directed.

S&F in repairs pillar tap, brass chromium plated fancy type with capstan heads, screwed down high pressure, screwed for iron pipe 15 mm bore complete all as specified and as directed.

S&F in repairs chromium plated grating with 100mm dia of approved make includingh fixing with 1:4 CM to floor/ nahni trap etc. complete all as specified and as directed.

S&F in repairs grating doom 125mm dia with waste hole of PTMT (minimum weight 40 gms) etc. complete all as specified and as directed.

S&F brass chromium plated tubular towel rail, 20mm dia, 'D' type 60cm long between flanges of brass CP complete all as specified and as directed.

S&F brass chromium plated health faucet alongwith 1.00 to 1.50 meter good quality SS flexible connection pipe suitable for 15mm bore pipe complete all as specified and as directed.

S&F brass chromium plated soap dish 150mmx150mm, of any type, fixed to plugs with chromium plated brass screws complete all as specified and as directed.

Taking down chowkats with shutters not exceeding 1.5 Sqm each (without taking off shutters from the frames) complete all as specified and as directed.

All as per srl item No.31 above but in before but exceeding 1.50 sqm and not exc. 4.00 sqm each complete all as specified and as directed.

Taking down shutter of any descreption exc. 1.00 sqm but not exc. 2.00 sqm each, complete all as specified and as directed.

S&F pressed steel frames of size 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified and as directed.

S&F factory made solid PVC chowkhat/ door frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet and edges will be painted to match with printed PVC sheet reinforced with 19mm x 19mm MS square tube of 19 gauge including rubber gasket, PVC fastners, screws, brackets, and shown on drawing as per SSR part-II (2020) complete all as specified and as directed.

S&F factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick wood grain printed moulded prelam PVC sheet on the front face & 2mm thick plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and as directed.

S&F 30 mm thick factory made flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

S&F 35 mm thick factory made IInd class hard wood glazed and Skelton shutters (three panels) open rebated and prepared to receive glass/ gauge etc. divided into squares edges of framing plain, chamfered or rounded mitered and rebated sash bar any number with cut or mitered beads for securing glass/ gauge etc. size of members of shutters complete all as specified and as directed.

S&F stainless steel butt hinges, size 100 mm complete complete all as specified and as directed.

S&F stainless steel barrel tower bolts, 150 mm long complete all as specified and as directed.

S&F stainless steel handles, 150 mm long complete all as specified and as directed.

S&F stainless steel sliding door bolts 250mm long with hasp, staple (bolt type) fixing clips of sheet cast, fixing bolts complete all as specified and as directed.

M&L for preparation of new wooden surfaces of any description not otherwise described over 10 cms width or girth and apply two coat of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L for preparation of old wooden surfaces of any description not otherwise described over 10 cms width or girth and apply one coat of synthetic enamel paint complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description not otherwise described over 10 cms width or girth and apply two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

M&L for preparation of old steel surfaces of any description not otherwise described over 10 cms width or girth and apply one coat of synthetic enamel paint complete all as specified and as directed.

S&F in repairs stainless steel wire cloth, 0.63mm nominal dia or wire and sqm average width or aperture 1.40mm, fixed with tinned tacks or galvanized wire staples to doors/steel windows complete all as specified and as directed.

S&F stainless steel wire cloth, 0.63mm nominal dia or wire and sqm average width or aperture 1.40mm, fixed with tinned tacks or galvanized wire staples to doors/steel windows complete all as specified and as directed.

S&F in repairs stainless steel barrel tower bolts, 150 mm long complete all as specified and as directed.

S&F in repairs stainless steel handles, 150 mm long complete all as specified and as directed.

S&F in repairs stainless steel sliding door bolts 250mm long with hasp, staple (bolt type) fixing clips of sheet cast, fixing bolts complete all as specified and as directed.

Dismantling wrought iron or mild steel/ cast iron work of any description complete all as specified and as directed.

M&L for mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/ or riveted, welded or forged into spikes, framed guard bars, window frames, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work fixed in position including holdfasts or screws confirming to Fe.290.Gde-E-165, complete all as specified and as directed.

M&L for welding in repairs exc 2.5 cm but not exc. 5.0 cm in length thickness of metal be welded exc 6mm but n.exc 9mm complete all as specified and as directed.

Taking down cement or cement lime plaster, any description, on brick or stone walls, concrete surface etc including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and as directed.

M&L for 15mm thick rendering with ready mix plaster on faces of brick or concrete surface, finished even and smooth without using extra cement complete all as specified and as directed.

M&L for 10mm thick rendering with ready mix plaster on concrete surfaces of ceiling, chajja,etc finished even and smooth complete all as specified and as directed. Notes for Srl item Nos. 56 & 57:- 1. Make of readymix plaster shall be Birla Aerocon/Ultratech Readiplast/ACC Accoplast/Fosroc Chemical (India) Pvt Ltd Renderoc and as approved by GE. 2. The readymix plaster shall be procured directly from the manufacturer or from their authorised dealer. 3 The contractor shall produce original purchase voucher of readymix plaster while claiming RAR/ Final Bill. 4. The Engr-in-Charge shall verify the genuineness of these purchase vouchers before endorcing.

M&L for preparation of newly plastered surfaces of wall and applying 1 to 2 mm thick wall care putty on whole surfaces to achieve smooth, even and uniform surface including grinding with sand paper and levelling of surface and applying two coat of oil bound distemper on white or tinted over existing prepared putty base surface complete all as specified and as directed.

M&L for preparation of newly plasered surfaces of walls and applying two coat of weather proof paint (APEX) over a coat of alkali resistant primer complete all as specified and as directed.

M&L for preparation of newly plasered surfaces of ceiling and applying three coat of white wash complete all as specified and as directed.

M&L for complete removal of existing treatment from internal surfaces of wall by electrically operated grinder, washing and filling of holes with filler material and applying 1 to 2 mm thick wall care putty in two layers on whole wall surface including grinding with sand paper and levelling the surface and than applying two coat of oil bound distemper on white or tinted surface over existing prepared putty based surface complete all as specified and as directed.

M&L for preparation of old surfaces of wall and applying two coats of white wash, complete all as specified and as directed.

M&L for preparation of old surface of ceiling and applying one coats of white wash, complete all as specified and as directed.

M&L for complete removal of existing treatment from external surfaces of wall by electrically operated grinder thereafter filling of holes and cracks with filler material and than applying two coat of cement based paint over a coat of cement primer complete all as specified and as directed.

Cutting of vegetable plant (girth not exceeding 300mm) from roof, terrace, chajjas etc digging out the roots and making good the surface in PCC 1:2:4 type B1 with surfaces finished to match complete including scaffolding etc. complete all as specified and as directed.

Dismantling of brick tiles (laid flat or on edge) on roof surface.laid bedded and pointed in any mortar complete all as specified and as directed.

Demolition of mud in roof, any thickness, including plastering and leeping upto two storey bldg including necessary scaffolding arrangement complete (whether full thickness removed or only a part there of) and removing rubbish from cantonment area or complete all as specified and as directed.

M&L for cutting out craks to V-section in existing roof or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3 complete all as specified and as directed.

M&L, Priming roof surfaces and applying water proofing treatment over roofs comprising of the following complete all as specified & as directed:-

(a) Applying oil bound bituminous primer at the rate of 0.30 Ltrs/Sqm as per IS 3384-1986 on prepared surfaces. Surface shall be kept free till the moment, the primer is impregnated and the solvent oil in primer is evaporated.

(b) Applying one coat of hot straight run bitumen @ 1.20 Kg/Sqm of grade 30/40 confirming to IS-73 (Grade S-35).

(c) Laying 3mm thick APP polymeric water proofing membrane of weight not less than 3.6 kg/sqm, black finish reinforced with non woven polyster matt, (weight not less than 160 gm/Sqm) with a thermo fusible finish, torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at sides and 100mm at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufacturer's instruction including preparation of surface.

make of APP: "Moply FP" manufactured by STP Texsa Ltd or Hyper Plas (Polyester) manufactured by M/S IWL Ltd or "Shaliplas"ter) manufactured by M/S Capital Steels and Chemical Pvt Ltd or Makpolyplast manufactured by M/S M K Patro as approved by GE.

Note :- The water proofing treatment shall be got carried out by the manufacturer or their authorised applicators. The contractor shall give 10 years guarantee for effectiveness of water proofing treatment, 2.5% of work done amount of this item shall be retained from contractors payment for a period of 10 years reckoned from date of physical completion of this work, or in lieu contractor may deposit bank FDR for the said amount for 10 years which shall be released by GE on expiry of satisfactory completion of 10 years period.

M&L for cement concrete tiles 20cm x 20cm x 20mm thick, machine pressed, set jointed and pointed in neat cement slurry in floors, and cut and polished laid over 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

M&L for cement concrete type B-1, 1:2:4 (using 20mm graded stone aggregate) in roof kerbs or mud stop rounded or chamfered on edge etc. complete all as specified and as directed.

Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required, complete all as specified and as directed.

S&F 100 mm dia cast iron (Sand Cast) soil, waste and vent pipes, in any length with or without ears, with cement joints, fixed to wall complete all as specified and as directed.

S&F 75 mm dia cast iron (Sand Cast) soil, waste and vent pipes, in any length with or without ears, with cement joints, fixed to wall complete all as specified and as directed.

S&F for 75mm cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and as directed.

S&F for 100mm cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and as directed.

S&F for 100mm cast iron Traps ‘P’ or ‘S’ complete all as specified and as directed.

S&F in repair for 75mm cast iron nahani trap/ floor trap with grating including jointing of waste pipe and fixed in cement concrete type B-1, 1:2:4 complete all as specified and as directed.

S&F in repairs 125mm x 100mm salt glazed stone ware gully traps square & round mouthered trap 'P' including case iron grating and fixed, including necessary excavation and earthwork, concrete in bed, surrounds, kerbs etc., and jointing to drains in CM 1:1 complete all as specified and as directed.

Taking down rain water pipe (any size) or pattern incl all fittings, head shoes, bends swan necks etc incl cleaning or re-fixing or removal to store (measured overall as fixed along the centre line over fittings and accessories complete all as specified and as directed.

S&F PVC (SWR) pipes, 110mm dia single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed.

S&F PVC (SWR) bends/ Tee any radius, 100mm bore complete all as specified and as directed.

S&F MS clamps 100mm bore out of 50mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and as directed.

All as per Srl item No.83 above but 75mm bore complete all as specified and as directed.

Demolition of cement concrete (un reinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level) complete all as specified and as directed.

M&L for cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) in plinth protection, 75 mm thick, finished even and smooth without using extra cement, including making joints 12mm wide to the full depth of PCC at every 3 metres and at every change of direction and filling the same with & including bitumen and sand 1:3 by weight complete all as specified and as directed.

M&L for 75mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base, complete all as specified and as directed.

M&L for 60mm thickness machine pressed pre-cast concrete interlocking paver block any size and shape confirming to IS 15658-2006, M-30 grade with grey cement and no pigment, laid over 40mm thick sand cushion and including joints filled with sand complete all as specified and as directed.

M&L for chipping of spelled and loose concrete and cleaning rust from reinforcement by sand blasting, scrubbing down concrete surfaces with wire brushes cleaning with water allowed to dry applying a layer of zinc rich epoxy primer as anti rust on all exposed reinforcement followed by a layer of bonding coat of a layer of epoxy adhesive on complete exposed surfaces of concrete and provide gunniting in two layers over steel welded mesh 2 mm dia of wire and total aperture 75 mm, thickness of gunite n.exc 25 mm thick (average thickness) using cement mortar 1 :2 with OPC 43 grade cement mixed with polycrete admixture @ 2 % by weight of cement or as per manufactures instructions and finally applying cement plaster over gunite surfaces of required thickness to give an even uniform and smooth finish conforming to proper geometrics in cement mortar 1:4 to match with the existing surface as in side and soffits of slabs, chajjas, fins, facias, parapets, columns and beams etc complete including necessary scaffolding , shuttering necessary chased to brick work or RCC members at any height upto full height of buildings including removing of small trees shrubs etc complete all as specified and as directed. Note: Steel mesh to be welded with the existing reinforcement. The cost of welded mesh is deemed to be included in the unit rate quoted.

M&L for providing and injecting chemical emulsion for Post Constructional Anti-termite Treatment along the external wall below concrete or masonary apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes, complete all as specified and as directed.

M&L for Anti-termite Treatment of soil under existing floors using emulsion one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar (1:2) to match the existing floors complete all as specified and as directed.

M&L for 15mm thick rendering with ready mix plaster on brick or concrete surfaces finished even and smooth without using extra cement mixed with by adding permeability reducing polymer @ 250gm/sqm (6%) by weight of cementitious content at time of mixing with water as per manufacturer's recommendations including all levelling the surface, curing etc complete all as specified and as directed. (water proofing compound to be measured separately).

Supply only liquid water proofing compound

M&L for preparation of new plastered wall surfaces and applying two coats of distemper oil emulssion, white or tinted over one coat of primer complete all as specified and as directed.

M&L for providing and applying a bond coat of Latex: Water : cement - 1:4:6 with latex consumption @100gm/sqm on the brick wall surface by brush as per manufacturer's recommendations including curing complete all as specified and as directed.

M&L for exposing the joint of masonry/concrete structure at ground level as required and the plastering must be knocked off at least 50 cm beyond the visibly penetrated area. Damaged mortar joints are to be scrapped out to a depth of approximately 2-3 cm complete all as specified and as directed undermentioned activities:- Drilling Holes : Drilling holes 10mm diameter in masonary/concrete structure along the side of the joint at 45 degree angle, so as to cross the brick/block at an interval spacing of 15-30 cm depending on extent of rising dampness as per recommendation of Engr-in-Charge. Cleaning of holes : Clean the holes by air blower prior to fixing nozzles and S&F injection packers of 9.8 mm diameter, 10 cm long in the holes and tighten by using Sikadur 31 & its equivalent product. Cutting of Packeers : Cut the packers after completion of grouting without damaging the structural elements.

Supplying and applying of a 3 part, very low viscous, Elastic Polyacrylic Injection Resin 306 with a versatile and adjustable reaction time having mixed viscosity : 3-11 M.pa.s at +20 Deg Centigrade. Reaction time : Adjustable according to ambient temperature and execution requirement between 8-50 mins, pH-9-10, Tested as per Wissbau No. 2002-094-(1A)-Function test with re-injectible hose system. The holes should be drilled until a depth of approx 5 cm (for a 6 cm thick wall) before the end of the wall is reached. Pump injection-306 at >20 bar into or behind fissures or into masonry joint which are allowing water to infiltrate into unwanted areas. If voids in masonry being injected contain insufficent moisture to activate the grout, inject a small amount of water prior to injecting the grout. When movement stop or Injection-306 appears at the next packer move to the next packer and inject. If the dampness is heavy, inject similarly at next joint line complete all as specified and as directed.

Taking down carefully old point wiring with aluminium/ copper conductor (Light / Fan/ Socket/ power Point) complete including fittings such as switches, light fittings,ceiling rose, pendent holders, bell, regulators and socket point etc and making good the disturbed surface & wall/ floor complete all as specified and as directed.

M&L for point wiring with PVC insulated unsheathed multi stranded FRLS type copper conductor cable of size 1.5 Sqmm 1100 V grade including one run of PVC insulated unsheathed multi stranded FRLS type copper conductor cable of size 1.5 sqmm as earth continuity conductor connected to common earth dolly in and including PVC concealed conduit 20 mm dia medium grade ISI marked and its accessories including provn of new factory made pressed steel modular switch/terminal box of suitable size and new modular front & back plates of approved colour/model of suitable size for housing the modular switches, sockets, fan regulators complete all as specified and as directed for the following:-

All as per Srl item No.99 above, but One light/fan/exhaust fan point controlled by one no, one way 5 Amp switch.

All as per Srl item No.99 above, but One bell/buzzer point controlled by one bell push.

All as per Srl item No.99 above, but One three pin 5 Amp socket outlet point controlled by one no, one way switch on independent board.

All as per Srl item No.99 above, but One three pin 5 Amp socket outlet point controlled by one no, one way switch on same board.

All as per item No.99 above but with 2.5 sqmm (for phase, neutral) and 2.5 sqmm (for continuous earth wire) cable for one 15/16 amp socket out let point on independent board.

Notes for srl item Nos. 98 to 99:- (i) Cutting chases for concealed conduit and making good in cement mortar is deemed included in unit rate. (ii) No cutting shall be done in the roof for laying PVC conduit for ceiling point wiring. In this specified portion wire shall run through the existing conduit or surface new conduit shall be provided as required. (iii) In case the wiring is encountered with any beam/column, then the wiring will run on surface to avoid any damage to the RCC portion.

S&F Moduler type switch 230/250 volts grade one way (as catered in point wiring above) complete all as specified and as directed of following rating :-

SP 6 Amp rating.

Bell push SP 6 Amp rating.

SP 16 Amp rating.

S&F Modular type socket outlet shuttered type flush mounting type, 230/250 volts grade (as catered in point wiring above) of following ratings:-

6 Amp multipurpose type.

6 Pin 16 Amp multipurpose type.

S&F electric bell AC 230 Volt ding-dong type complete all as specified and as directed.

S&F ceiling rose 3 terminal/PVC insulated body ISI Marked complete all as specified and as directed.

Disconnecting mains connection and taking out old sub main wiring single core 4/6/10 sqmm and one single core 2.5/4/6 sqmm aluminum/copper conductor cable from the concealed conduit from the wall/ceiling and making good to the disturbed surface complete all as specified and as directed.

M&L in repairs submain wiring with PVC insulated unsheathed copper conductor multi stranded FRLS type 1100V grade 2 x 6 Sqmm complete drawn in new PVC concealed conduit of 20 mm dia and its accessories along with 1 x 6 Sqmm PVC insulated unsheathed copper conductor multi stranded FRLS type cable for continuous earth wire and duly connected to common earth dolly complete all as specified and as directed. Note : 3 runs of copper conductor shall be measured and paid as one unit.

M&L in repairs submain wiring with PVC insulated unsheathed copper conductor cable, multi stranded, single core, FRLS type, 1100 volts grade 2 x 10 sqmm complete drawn in new PVC conduit of 20 mm dia along with 1x 10 sqmm PVC insulated unsheathed copper conductor cable, multi stranded, single core, FRLS type for continuous earth wire and connected to common earth dolly complete all as specified and as directed. Note : 3 runs of copper conductor shall be measured and paid as one unit.

Disconnecting mains connection and taking out old sheet steel enclosure (DB) with metal clad 2 pin and earth plug and socket SPN, 20 amps distribution board and making good to the disturbed surface complete all as specified and as directed.

S&F factory made sheet steel enclosure (DB) with metal clad 2 pin and earth plug and socket SPN, 20 amps, 240 volts AC complete with one SP MCB, 20 amps complete all as specified and as directed.

Disconnecting mains connection and taking out old distribution board 8/12 way SPN with 200 amp rated bus bar complete with MCB and making good to the disturbed surface complete all as specified and as directed.

S&F factory made sheet steel distribution boards, double door, SPN, 8 way, concealed type, 240 volts AC with suitable busbar, neutral link, earth link suitable for MCB, DP/SPN as incomer & MCB SP as outgoing complete all as specified and as directed.

S&F in repairs of MCBs, 10 KA rupturing capacity, IS-8828 marked, of the under mentioned type and rating and fixing in DBs (DBs Catered separately in this schedule) complete all as specified and as directed:- Note : Make of the MCB should be the same as that of DB

SP 6 to 32 Amps 'B' Curve.

SPN 40 to 63 Amps 'C' Curve.

S&F LED Tube Light of 20 Watt 230Volt(size 4 ft) , box type complete with LED Tube Light 20 Watt & all accessories internally prewired including connecting up with three core sheathed flexible copper conductor cable of suitable size complete all as specified and as directed.

S&F of 2x2 Panel light Recessed mounted LED light of 36 W fixture with opal diffuser to give glare free light including suitable LED light of 36 W complete all as specified and as directed.

S&F of 1x4 Panel light surface mounted LED light of 40 W fixture with opal diffuser to give glare free light including suitable LED light of 32 W complete all as specified and as directed.

S&F of street light fitting 25 watt outside the building including GI bracket of suitable size,fixing with clamp complete all as specified and as directed.

S&F in repairs decorative LED type post top lanterns luminaire 40 watts, outdoor type for 360 degree indirect light with resistant to corrosion, glare free having better uniformity with suitable driver complete all as specified and as directed.

M&L for taking down of ceiling fan/exhaust fan/WALL fan of any size and servicing complete, greesing, painting, changing of ball bearing of any type, Copper rewinding and marking of MES No. etc at site and refixing complete all as specified and as directed.

S&F stepped type Modular type 2M electronic fan regulator etc. as required complete all as specified and as directed.

S&F in repairs of factory made load line DB's double door made out of CRCA mild steel sheet with insulating materials like polyester epoxy coated surface mounting 4 way TPN 415 Volts, IP 43 with suitable busbar, neutral link & earth link suitable for MCCB TP as incomer & MCB SP/TP as out going including taking down of Old VTPN for credit complete all as specified and as directed.

S&F in repais MCCB, 4 pole, 415 volt of capacity 160 amp, breaking capacity not less than 16 KA, Icu=100% Ics thermal magnetic type adjustable type 80 to 100 % confirming to IEC-60947-II, IS-13947-II, including thimbles, nuts, bolts, washers etc and connections, replacement of thimbles, minor parts like nuts bolts washer etc. complete all as specified and as directed.

S&F factory made (CPRI test certified manufacturer) LT feeder pillar box of minimum size 300 cm x 150 cm x 90 cm, Outdoor type, wall mounted, cubical compartmentalized type suitable for 415 volts, 3 phase, 4 wire (100% neutral), 50 Hz supply system all as specified and directed having busbar chamber with insulated aluminium busbar 400 Amps rating (100% neutral) installed on porcelain insulators. The panel shall be dust and vermin proof made of 2 mm CRCA MS sheet and suitable iron frame work duly powder coated finish. Front opening type with aprons for cable entry with locking arrangement including internal wiring with PVC insulated multistranded copper conductor FRLS cables of suitable size fixed on wall by grouting suitable bolts in wall tightening with washers & nuts including making good the disturbed surface, thimbling and cable entry boxes with cable gland. The scope of the work also includes supply and fixing the following:-

M&L for plate earthing complete with galvanized mild steel plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground vertically (in earth pit not less than 2.25 meter deep below ground level) with the top edge of earth plate at a depth not less than 1.5 meter below normal ground level, the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15 cm on all sides and including GI strip 32x6 mm bolted (with GI nuts, bolts & check nuts) and riveted to earth (Plate) electrode at one end and connected to main switch board test point at the other and watering GI pipe (medium grade) 20 mm bore from bottom of earth pit to top of electrode and 40 mm GI pipe light grade for earth strip protection complete with earth pit in PCC 1:2:4 type B0 using 12 mm graded crushed stone aggregate, RCC cover etc.

S&F in repairs earth continuity conductor or main earthing lead fixed to wall on batten or reccess or chases or burid in ground or drawn in conduit/ pipe or fixed to poles or any other indicated situation for loop earthing etc as required 32X6 mm galvanised iron strip.

Taking out old unserviceable under ground XLPE/ PVC cable of any size from trenches/ wall/roof/road/pipe/pole including taking out of brick layer and sand from trenches etc for removing from site complete all as specified and as directed by Engineer-in-Charge.

Supply, laying and testing UG cable XLPE Insulated 1100 Volts, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 120 sq mm 3.5 core.

Supply, laying and testing UG cable XLPE Insulated 1100 Volts, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 95 sq mm 3.5 core.

Excavation in trenches in any type of soil not exceeding 1.5 mtr wide and not exceeding 1.5 metre in depth for laying of LT under ground cable/ GI pipe complete all as specified

Returning filling including spreading, leveling watering and well ramming in layers n. exc 25 cm thick in any type of soil complete all as specified.

Removing excavated materials to a distance not exec. 50 mtr and deposing where directed at a level not exec 1.5 mtr above the starting point all as specified.

M&L for Best quality, locally available, sub class ‘B’ bricks (Old Size) for cable protection cover, laid flat and dry in trenches over the cable , perpendicular to the direction of cable complete all as specified and as directed by Engineer-in-Charge.

Supply and spreading river sand for cushioning of cable , with dry and clean sand, over and under the under ground cables in trenches, ducts for cable protection including consolidation, 80mm thick to the authorized width as per SSR Part-I before laying of cable and 150mm thick after laying of cable and gently punning down to 180mm thick complete all as specified and as directed.Note:Punned thickness only shall be measured and paid.

Note:- The contract sum shall be after deducting the amount of Credit shown in Credit Schedule of this Tender.

verma enterprises

M/S.M.S.Devi.Const.Co