REPAIR/REPLACEMENT OF UG CABLE, CIRCUIT BREAKER, STREET LIGHT, LT PANEL BOARD, CAPACITOR BANK, SWITCH AND MISC ELECTRICAL WORK AT VSB UNDER GE (AF) TUGHLAKABAD

Amount

Excavation in trenches soft/loose soil not exceeding 1.5 mtr wide in not exceeding 1.5mtr in depth for foundation etc or for shaft well, cesspits, manholes, fire hole etc n.exc 10 Sqmm on plan and not exceeding 1.5mtr in depth and getting out complete all as specified and as directed by the Engr-in-Charge

Returning filling in including spreading, leveling, watering and well ramming in layers not exceeding 25cm complete all as specified and as directed by the Engr-in-Charge

Removing excavated material not exceeding 50mtr and depositing where directed at a level not exceeding 1.5mtr above the starting point complete all as specified and as directed by the Engr-in-Charge

M&L for sand cushioning in trenches for protection of LT under ground cable including watering and consolidation complete all as specified and as directed by the Engineer-in-Charge.

Supply and laying well burnt sub class ‘B’ bricks, locally available in trenches for protection of underground cable complete all as specified and as directed by the Engr-in-Charge

M&L for jointing, testing and commissioning in replacement heat shrinkable straight through Jointing Kit suitable for LT Cable of size 70 Sq mm to 120 Sqmm, 3.5/4 core complete all as specified and as directed by the Engr-in-Charge. Make:- Denson/M seal/3M

All as per item no 06 but size 25 Sqmm to 50 Sqmm, 3.5/4 core complete all as specified and as directed by the Engr-in-Charge. Make:- Denson/M seal/3M

Taking down old UNSV security light fittings from pole upto 11 mtr height and S&F new LED street light fitting of capacity 60 watt 6000K, made up of pressure die cast housing with toughened glass and individual high power LEDs, IP66 protection, peanut lens and impact resistance of IK07 with 10KV built in surge protection device having top opening separate driver compartment comp complete all as specified and as directed by the Engr-in-Charge. Make-Havells/Philips/Wipro/Bajaj

Taking down old UNSV security light fittings from pole upto 11 mtr height and S&F new LED street light fitting of capacity 90 watt 6000K, made up of pressure die cast housing with toughened glass and individual high power LEDs , IP66 protection, peanut lens and impact resistance of IK07 with 10KV built in surge protection device having top opening separate driver compartment complete with complete all as specified and as directed by the Engr-in-Charge. Make-Havells/Philips/Wipro/Bajaj

M&L in replacement of cable XLPE insulated screened PVC bedded, galvanized steel wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of following sizes complete all as specified and as directed by the Engr-in-Charge. Make- Havells/Plaza/Gloster/Universal

120 Sqmm 3.5 core

95 Sqmm 3.5 core

70 Sqmm 3.5 core

50 Sqmm 3.5 core

35 Sqmm 3.5 core

16 Sqmm 4 core

10 Sqmm 2 core

Taking out old Unserviceable street light timer switches, M&L inclding testing and commissioning of NATURE Switch for outdoor lighting automation using space grade sensors and an advances micro controller suitable for outdoor use having features Automatic Switching ON at Sunset, Automatic Switching OFF at dawn, No clock setting and time settings wide operating voltage range, High voltage trip and auto reset having specification 230 Volts, 50 Hz complete with all connected accessories of rating 12 KW 3 phase, current range not less than 63 Amps complete all as specified and as directed by the Engr-in-Charge. Make- KAKTIYA ENERGY SYSTEM Model No- SWADEEP – 02EC 12kW3P/L&T/Havell's

Supplying and laying in replacement of synthetic Rubber insulated mats 2.5 mm thick for voltage upto 11 KV for electrical purpose as per IS 15652-2006, superseding IS 5424) suitable for electrical shock safety of sizes 2m x 1m , black in colour complete all as specified and as directed by the Engr-in-Charge. Make: Duratuf/Dunlop

M&L in replacement of PVC flat twin core cable with aluminium conductor of size 10 Sqmm 2 core suitable for 1100 volts power supply complete all as specified and as directed by the Engr-in-Charge.

M&L in replacement of PVC flat twin core cable with copper conductor of size 06 Sqmm 2 core suitable for 1100 volts power supply complete all as specified and as directed by the Engr-in-Charge.

S&F in replacement copper wire in wiring circuits as per site requirements HRFR-PVC insulated single core 1.5 Sqmm 1100 volts grade multi stranded conductor complete all as specified and as directed by the Engr-in-Charge. Make of cable - Havells/Finolex/Plaza

S&F in replacement copper wire in wiring circuits as per site requirements PVC insulated single core 2.5 Sqmm 1100 volts grade multi stranded conductor complete all as specified and as directed by the Engr-in-Charge. Make of cable - Havells/Finolex/Plaza

Taking out by disconnecting/unscrewing all electrical connection of UNSV post top light and M&L including testing for post top of 35 watts capacity suitable for 240 volts, 50 Hz, IP 65 single phase power supply, light, spun aluminium landscape luminaire with high power LEDs as light source complete with all standard accessories complete all as specified and as directed by the Engr-in-Charge. Make- Havells/Philips/Bajaj

Taking out old UNSV landscape light from the existing position and M&L including testing and commissioning for landscape luminaire aluminium cast for diffused lighting with high power LEDs as light source having height 1.0 meter of 25 watts capacity suitable for single phase, 240 volts, 50 Hz, IP 65 power supply complete all as specified and as directed by the Engr-in-Charge. Make- Havells/Philips/Cromption. Note- Necessary PCC work and excavation is deemed to be included quoted rates.

Taking out by disconnecting/unscrewing all electrical connection of UNSV flood light and M&L including testing for flood of 60 watts capacity suitable for 240 volts, 50 Hz, IP66 protection, single phase power supply, fabricated with die cast aluminium with high power LEDs as light source complete with complete all as specified and as directed by the Engr-in-Charge. Make- Havells/Philips/Crompton

Taking out by disconnecting/unscrewing all electrical connection of UNSV flood light and S&F of flood of 100 watts capacity suitable for 240 volts, 50 Hz, IP66 protection, single phase power supply, fabricated with die cast aluminium with high power LEDs as light source with all accessories complete all as specified and as directed by the Engr-in-Charge. Make- Havells/Philips/Crompton

S&F in replacement Energy saving 150 Watt environmental friendly, long life, exclusive innovative die cast aluminium IP66 flood light in LT pole with high power LEDs as light source, suitable for highlighting architectural features with all electrical accessories complete all as specified and as directed by the Engr-in-Charge. Make: Crompton/ Bajaj/Havells

Taking out by disconnecting/unscrewing all electrical connection of UNSV vertical medium bay light and M&L including testing for vertical medium bay light of 100watts capacity suitable for 240 volts, 50 Hz single phase power supply, fabricated with die cast aluminium with high power LEDs as light source, IP-54 with all standard accessories complete all as specified and as directed by the Engr-in-Charge. Make- Havells/Philips/Crompton

Taking out old UNSV bus chamber of any rating and S&F aluminium bus bar chamber current rating 200 amps 4 way type suitable for 415 Volts, 50 Hz AC supply complete making all incoming and outgoing connections all as directed by Engr-in-charge. Make- Havells/L&T/Simens

Taking out old UNSV Changeover switch of any rating and S&F of aluminium bus bar Off-load changeover switch AC 20 having current rating 400 amps 4 pole, 415V AC, in Sheet metal enclosure and side handle complete all as specified and as directed by the Engr-in-Charge. Make- Havells/L&T/Simens

Taking out old UNSV Changeover switch of any rating and S&F of aluminium bus bar Off-load changeover switch having current rating 200 amps 4 pole, 415V AC, in Sheet metal enclosure and side handle complete all as specified and as directed by the Engr-in-Charge. Make- Havells/L&T/Siemens

Taking out old UNSV MCB any type and M&L for MCB C series TPN 40-63 amps, 4 pole rating, as per IS 60898-1, 415 volts, 50 Hz, 10 KA, complete all as specified and as directed by the Engr-in-Charge. Make- Indoasian/Havells/Polycab

S&F in replacement of following amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and as directed by the Engr-in-Charge:

SPN 32 AMP

SPN 40 to 63 AMP

S&F in replacement of 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and as directed by the Engr-in-Charge.

All as per item no:28 above but of 40 Amps complete all as specified and as directed by the Engr-in-Charge.

M&L for providing cement concrete (1:2:4) type B2 using 40 mm graded stone aggregate in foundation, filling and mass concrete including dismantling existing complete all as specified and as directed by the Engr-in-Charge.

S&F in replacement of GI pipe of size 50mm dia, 'light grad', galvanised, with all fitting, laid in trenches for cable crossing through road & path ways, complete all as specified and as directed by the Engr-in-Charge.

S&F in replacement of GI pipe of size 80mm dia, 'light grad', galvanised, with all fitting, laid in trenches for cable crossing through road & path ways, complete all as specified and as directed by the Engr-in-Charge.

M&L for Excavation by Trench less Boaring Technology for holes under road, pavement, hard standing using Ultra sound technique and engaging necessary Machine including HDPE pipe ISI marked of upto dia 100 MM suitable for 0.4 MPA working pressure complete all as specified and as directed by the Engr-in-Charge. Note - HDPE pipe and making good the disturbed surface is deemed to be included in rate quoted by the Contractor

Taking down /dismantling of old UNSV solar street light from the existing location, M&L for servicing and testing, commissioning of solar street light including replacement of unserviceable component like solar street light lamp having luminaire 15 Wattage, LED type, Maximum power point tracking (MPPT) SCC solar charge controller, Mono Crystalline SPV panel of 30 watts & making them serviceable, complete all as specified and as directed by the Engr-in-Charge.

S&F in replacement of Solar battery, maintenance free, 12V, 65Ah, complete all as specified and as directed by the Engr-in-Charge.

M&L for taking out the unserviceable LT Panel board including all connection and supply, installation, commissioning and testing of LT panel, outdoor type, double door, IP 65 Protection, CPRI Approved base frame mounted dust proof and vermin proof with bus bar of 1000 Amps current capacity to accommodate 3phase, 415Volt with suitable aluminium bus bar designed as per relevant IS connected to bus bar by aluminium strip of suitable Size, fabricated out of 3.15 mm thick CRCA sheet for outer chamber and 2 mm thick for partition and doors and painting with seven tank process with twin shutter closing, locking arrangements and with 2 nos earthing sprout connectors complete and fixed in PCC (1:2:4) type B-1 using 20 mm graded stone aggregate as in foundation 45 cm above ground level mounted on angle iron base frame not less than 50x50x6mm angle iron, complete with control wiring for the above accessories complete all as specified and as directed by the Engr-in-Charge. (a) Bus bar chamber of 3 phase 4 strip 415 volts with 1000 Amps main and 450 amps Neutral, Alu strip 1 set Supported on insulated plate form, interconnection of all incomings & outgoings. (b) MCCB 4 pole in coming 630 Amp 50 KA with thermal/magnetic setting. -01 Nos (incomer) (c) MCCB 3 pole out going 400 Amp 36 KA with thermal/magnetic setting.= 02 Nos (outgoing) (d) MCCB 3 pole out going 315 Amp 36 KA, with thermal/magnetic setting. = 03 Nos (outgoing) (e) MCCB 3 pole out going 250 Amp 36 KA, with thermal/ magnetic setting. = 04 Nos (outgoing). (f) Spare Pocket for Mounting MCCB = 01 Nos. (g) Digital Voltmeter 0-500 volt = 01 Nos. (h) Digital Amp meter 0 -600 Amp = 01 (j) Indicator lamp yellow , Red , blue. (k) Complete wiring of the panel board. (l) CT ratio 600/5 amps

Dismantling of old existing looping box including disconnecting of incoming/outgoing cables& removing from site, Supply, installation and testing of Non transparent SMC Kiosks box 3 phase with 4 Nos bus bar, 63 amps aluminium 4 wire and 01 Nos MCB of 6 amps factory made, outdoor type, locking arrangement, front side of suitable size 300x200x100mm complete all as specified and as directed by the Engr-in-Charge. Make- Universal Switch Gear Control/L&T/ Hensel/Sintex

M&L for supply, installation and testing in replacement of Earthing complete with galvanised steel earth plate electrode 60×60cm× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to but using galvanised iron strip 25×4mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 5 connected to earthing test point all as specified or indicated including testing on completion complete all as specified and as directed by the Engr-in-Charge.

S&F in replacement of Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 25x4mm galvanised iron stripe, complete all as specified and as directed by the Engr-in-Charge.

M&L for servicing & testing of ACB 4 Pole, 415 V, with thermal magnetic release (manual fixed type) of capacity 1600 amps, after taking proper shut down complete all as specified and as directed by the Engr-in-Charge. Note: All the components required at is deemed to be included in quoted rate.

S&F in replacement MCCB 400 Amps 4 Pole breaking capacity 36 kA,415 V,suitable for existing LT panel Adjustable type, conforms to IS/IEC 60947-2 & IEC 60947-2, ICS=100 % of ICU with spreader terminals complete all as specified and as directed by the Engr-in-Charge. Make: Havells /Legrand/L&T

All as per item No: 42, but MCCB of 250Amp, 4 pole, 36 kA complete all as specified and as directed by the Engr-in-Charge.

All as per item No: 42 but MCCB of 200Amp, 4 pole, 36 kA complete all as specified and as directed by the Engr-in-Charge.

All as per item No: 42 but MCCB of 125Amp, 3 pole, 16 kA complete all as specified and as directed by the Engr-in-Charge.

All as per item No: 42 but MCCB of 100Amp, 3 pole, 16 kA complete all as specified and as directed by the Engr-in-Charge.

All as per item No: 42 but MCCB of 63Amp, 3 pole, 16 kA complete all as specified and as directed by the Engr-in-Charge.

S&F in repair of digital Voltmeter of range 0-500 Volts single phase, Class 01 of size 96 x 96mm suitable for existing LT panel complete all as specified and as directed by the Engr-in-Charge. Make AE/HPL/Legrand

S&F in repair of digital Amp meter with CTs 0-300 Amps single phase, class 01 of size 96 X 96mm suitable for existing LT panel complete all as specified and as directed by the Engr-in-Charge. Make AE/HPL/Legrand

S&F in replacement of CT of capacity 300/5A, 10VA including complete wiring with existing system, complete all as specified and as directed by the Engr-in-Charge.

S&F in replacement 1'x1' size LED panel lighting luminaire glare free illumination fitting size 300x300mm (LXWXH) of 15 watts capacity surface mounting with high brightness SMD LEDs complete all as specified and as directed by the Engr-in-Charge. Make- Havells/Philips/Wipro

S&F LED lamp 9 watt suitable for B22 base complete all as specified and as directed by the Engr-in-Charge. Make : Havells or equivalent wipro/Phillips.

S&F in replacement of Modular switch 1 way 6A, 1 module, 230 Volt, flush button single pole one way complete all as specified and as directed by the Engr-in-Charge.

S&F in replacement of Socket, 6A - 2/3 pin combined 2 module 230 Volt flush type complete all as specified and as directed by the Engr-in-Charge.

S&F in replacement of Modular switch 1 way 16A, 1 module, 230 Volt, flush button single pole one way complete all as specified and as directed by the Engr-in-Charge.

S&F in replacement of Socket 6A/16A - 2/3 pin combined 2, module 230 Volt flush type complete all as specified and as directed by the Engr-in-Charge.

S&F in replacement of LED lights fitting 1x 20W, 220V, AC retrofit type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed by the Engr-in-Charge.

Dehydration and filtration of the existing transformer/servo voltage stablizer oil by Dehydration plant to achieve di-electric strength of 40 KV at the gap of 4mm complete all as specified and as directed by the Engr-in-Charge. (Dehydration plant shall be brought at site by the Contractor) and shall also include the following provisions :- 100 (a) Testing of transformer /servo voltage stabilizer oil before & after dehydration shall be carried out as directed. (b) The Unit of Payment under this item shall be per liter of oil meant for all processes to the entire completion of jobs. (c) Contractor will maintain a register of dehydration and filtration of each and every equipment as per format given by Engr-in-charge and submit the same to Engr-in-charge.

Supply and filling transformer oil for topping up or replacement in different existing transformers outdoor/indoors type of any capacity located and installed at different places and different height complete all as specified and as directed by the Engr-in-Charge. Make: Power oil. Note: - Transformer Oil:- The entire quantity of transformer oil shall be procured in one go. The complete material shall be brought at site and then as per requirement oil should be shifted to site. The Purchase Vrs of transfer oil will be verified by AGE personally and certificate for the supply of genuine transformer oil shall be kept on record. Cost of this aspect deemed to be included in the quoted rate

Supply and replacement of dehydrating agents (Silica gel) in transformers of capacity upto 1000KVA transformer outdoor/indoor type complete all as specified and as directed by the Engr-in-Charge.

Supply and replacement of LT bushing (Brass stud and bolts with porcelain insulator) suitable size to fixed the transformer capacity range 1000 KVA including replacement of gasket, cable glands, etc to make the transformer leak proof complete all as specified and as directed by the Engr-in-Charge.

Supply only ceramic bushing and Gasket on LT side of transformer of 1000 KVA capacity, complete all as specified and as directed by the Engr-in-Charge. Make: Mysore Potteries/BHEL/Jaipuria/ITE Transformer.

All as per item No: 62 above, but on HT side of transformer of 1000 KVA capacity, complete all as specified and as directed by the Engr-in-Charge. Make: Mysore Potteries/BHEL/Jaipuria/ITE Transformer

S&F of aluminium lugs of short barrel complete all as specified and as directed by the Engr-in-Charge of following size:

Size of 25 Sqmm

Size of 35 Sqmm

Size of 50 Sqmm

Size of 70 Sqmm

Size of 95 Sqmm

Size of 120 Sqmm

Size of 150 Sqmm

Size of 185 Sqmm

Size of 240 Sqmm

M&L for painting to LT steel tubular poles along with cross arms, clamps, channels, bracing etc complete with machine spray after cleaning and preparation the surfaces, externally with two coats of aluminium paint duly making 30 cm width circular bands of 03 Nos alternatively 1 meter from ground level with blue paint making back ground and writing numbering of poles complete all as specified and as directed by the Engr-in-Charge.

M&L for painting of transformer complete with two coats of synthetic enamel paint of approved colour including removing of all loose paints, oils dust, rust etc including painting/marking of SM No/MES No, capacity etc for 1000 KVA capacity complete all as specified and as directed by the Engr-in-Charge.

M&L for painting of LT Panel complete with two coats of synthetic enamel paint of approved colour including removing of all loose paints, oils dust, rust etc of any size, complete all as specified and as directed by the Engr-in-Charge.

Taking down old UNSV security light driver from pole fitting upto 11 mtr height and S&F new electronic LED driver suitable for fixing in any make 45/60 Watt LED Light Fitting complete all as specified and as directed by the Engr-in-Charge. Make- Bajaj/Philips/Havells

S&F in replacement of brass battery lugs suitable for solar light battery terminal, complete all as specified and as directed by the Engr-in-Charge.

S&F in replacement of bracket made of GI pipe light grade 40mm bore bent to shape as required at site for street light fitting 1.2 m in length and fixed on wall/pole including necessary MS clamps, nuts, bolts etc complete all as specified and as directed by the Engr-in-Charge.

M/s Prakash Enterprises

M/S Delhi Engineering Co.

POOJA ENTERPRISES