GE 861 EWS-58/2023-24

Amount

Excavation in trenches not exceeding 1.5 Mtr wide and not exceeding 1.5 Mtr deep in soft/loose soil and getting out for taking down/laying pipe lines of any description and in any position including forming sides and bottom surface to required level/ gradients complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm in depth, complete all as specified and directed.

Removing excavated material n.exc. 50m and depositing where directed at a level n.exc. 1.5 m above the starting point, complete all as specified and directed.

Disconnecting and taking up or down old existing 80mm steel tubing and connections of any description/grade and in any position in trenches/under floors/on walls etc including connected fittings/ accessories and fixtures like bib-taps/stop valves etc. all as directed and specified

All as per item 4.01 here-in-before but 50mm dia.

All as per item 4.01 here-in-before but 40mm dia.

All as per item 4.01 here-in-before but 25mm dia.

All as per item 4.01 here-in-before but 20mm dia.

All as per item 4.01 here-in-before but 15mm dia.

Laying only 80mm dia old steel water tubing and connections of any description/any grade and in any position obtained in serviceable condition from taking down, in new or old position as in trenches with using new fittings i.e. bends/Tee/ sockets/ reducers/elbow etc. including cutting/making new threads at the ends of old pipes, complete all as specified and directed.

All as per item 5.01 here-in-before but 50mm dia.

All as per item 5.01 here-in-before but 40mm dia.

All as per item 5.01 here-in-before but 25mm dia.

All as per item 5.01 here-in-before but 20mm dia.

All as per item 5.01 here-in-before but 15 mm dia.

Supply, laying, jointing and testing in trenches, 80mm dia galvanized iron water tubing medium grade (ISI marked) including provision of all necessary steel fittings/ accessories complete all as specified and directed

All as per item 6.01 here-in-before but 50mm dia.

All as per item 6.01 here-in-before but 40mm dia.

All as per item 6.01 here-in-before but 25mm dia.

All as per item 6.01 here-in-before but 20mm dia.

All as per item 6.01 here-in-before but 15 mm dia.

Taking up/down existing 100mm bore cast iron pipe lines/water mains of any description and in position including fittings, accessories and fixtures etc existing in between pipe line, by taking out and opening any type of joints (Tyton/Gasket / Lead joints) complete all as specified and directed. Note : While taking out of water main existing lead shall be recovered by burning out joints carefully from the existing joints of the water mains and shall be the contractor’s property and credit recovery shall be made for the same.

Laying only in trenches of 100mm bore flanged end cast iron pipes of any description/grade and in any position, as obtained from taking up or down, after making necessary addition / alterations and properly cleaning the pipes complete all as specified and directed. Note : (i) Earth work, Joints and CI specials/ fittings of the pipes shall be measured and paid for separately under appropriate item of Schedule `A'. (ii) Joints of the pipes shall be measured and paid for separately under appropriate item of Schedule `A'.

Supplying, laying, jointing & testing of 100mm bore cast iron pipes with flanged ends centrifugally cast (spun cast) class B in trenches or at vertically position at OHT suitable for run leads joints complete all as specified and directed by Engineer-in-Charge for the following size:- Note :- (i) Earth work, Joints and CI specials/fittings of the pipes shall be measured and paid for separately under appropriate item of Schedule `A'.

Supplying and fixing in repair cast iron specials / fittings such as bend, tee, socket, collar, reducer, tail pieces etc. suitable for 100mm flanged end pipe, complete all as specified and directed.

Supply, fixing, jointing and testing, 50mm gun metal globe/gate valve of approved quality, ISI Marked, with iron wheel head, both ends screwed for iron pipe including taking down of old one complete all as specified and directed.

All as per item 11.01 here-in-before but 40mm dia.

All as per item 11.01 here-in-before but 25mm dia.

All as per item 11.01 here-in-before but 20mm dia.

All as per item 11.01 here-in-before but 15 mm dia.

Supply, installation, fixing, jointing and testing, 100mm cast iron sluice valve of approved quality, ISI Marked, class PN-1.6 conforming to IS-14846 of 2000 both ends flanged with iron wheel head and stainless steel spindle, long body type, jointed and tested including taking down of old one complete all as specified and directed.

All as per item 12.01 here-in-before but 80mm dia.

Supply, fixing and testing of 100mm dia cast iron non return valve of approved quality, ISI Marked, PN 1.6, both ends flanged jointed including taking down of old one complete all as specified and directed.

Supply, fixing and testing of 100mm dia cast iron butterfly valve of approved quality, ISI Marked, PN 1.6, both ends flanged jointed including taking down of old one complete all as specified and directed.

Material and labour for rubber gasket joints in 100mm bore flanged end cast iron pipes and fittings complete with and including minimum 3mm thick rubber /fiber gasket and necessary nuts/bolts/washers including dismantling of flanged pipe joint, complete all as specified and directed.

All as per item 15.01 here-in-before but 80mm bore.

Burring out run lead joint of 100mm bore CI pipe line, complete all as specified and directed. (Note: Lead shall be recovered by burning out joints carefully from the existing joints of the water mains and shall be the contractor’s property and credit recovery shall be made for the same)

Material and labour for run lead joints including caulking properly for the 100mm bore CI pipes/fittings etc, complete all as specified and directed.

M&L for cutting of the existing 100mm bore CI pipe line for rectifying leakage and reducing to required length, in position, for insertion of collars or other fittings including dewatering etc complete all as specified and directed.

All as per item 18.01 here-in-before but 80mm bore.

Material and labour for fabricating and fixing pipe line MS clamp of flat iron made to shape along with nuts, bolt washers etc suitable for pipe line all as specified and directed for stopping leaking of pipe lines of any description and in any position clamps shall be shape and size as approved, tightened with suitable nuts, bolts washers as directed by Engineer-in-charge. Note: - (i) Weight of clamps including nuts, bolts and washer shall be measured for payment purpose. (ii) Clamp shall be tightened with using suitable rubber washers. (iii) Clamp shall be provided two coats of black bituminous paints over a coat of red oxide primer after preparation of surface.

Material and labour for construction of brick masonry valve pit /chamber complete with 3mm thick MS sheet cover with locking arrangement of size 600mm x 600mm x 600mm (depth) (internal dimensions) as shown on Drg No CWE /TD/129 sheet No 1/1 dated 18.12.87 with and including necessary excavation & earth work in any type of soil including dismantling & breaking down the existing valve pit chamber of any size and any shape complete all as specified and directed.

All as per item 20.01 here-in-before but of internal size 900mm x 900mm x 900mm.

Material and labour for rectifying leakage of 80mm GI pipe line including excavation in mud (not exc 6.1mx0.7m x0.7m) and making arrangement for dewatering by using electric/diesel pump/manual additional labour, for taking out old jointing fitting and S&F new jointing fitting such as socket, nipple,union,elbow and reducers as applicable complete all as directed.

All as per item 21.01 here-in-before but 50mm dia.

All as per item 21.01 here-in-before but 40mm dia.

All as per item 21.01 here-in-before but 25mm dia.

All as per item 21.01 here-in-before but 20mm dia.

All as per item 21.01 here-in-before but 15 mm dia.

M&L for scraping removing and cleaning of interior surface of overhead reservoir of capacity 25000 Gallons at 36 feet staging height cleaning with Alum water with brush after removing the mud /silt in side the tank to the satisfaction of Engr-in- charge including two coats of white washing to inner surface to tank and two coats of cement base paint outside of the tank and writing date of cleaning and capacity to tank with synthetic enamel paint of size 10cm height on tank complete and all as specified and directed.

All as per item 22.01 here-in-before but capacity 50000 Gallons.

Lifting from borewell and disconnecting the existing non functional submersible pump set from supply, dismantling existing CI bend from non return valve, removing and lifting out submersible pump set of any description and capacity & in any position, alongwith existing column pipe and existing submersible cable of any size from the bore well 150mm bore (approximately 40 mtr depth of pump set from GL) complete all as specified and directed. Note: 1. Contractor shall take proper precautions while lifting out and removing pump set from bore well so as to avoid any damage to column pipe and submersible cable. All necessary T&P and equipments required for lifting out pump set etc shall be arranged by the contractor at his own cost 2. Taking out of Sunken submersible pump sets if any shall be measured and paid for separately under appropriate item of Schedule `A' without making any adjustment in above rates

Dismantling and strip opening of 20 to25 HP, three phase, 415 Volts, 50 Hz, AC, submersible pump & motor of any description and in any position for servicing / overhauling, cleaning, oiling/greasing, fixing of serviceable parts in position, removing & replacement of defective / unserviceable parts with new parts, reassembling the Pump & motor, ensuring proper alignment of pump and motor, fixing in position, connecting to existing system and testing at site on full load to the entire satisfaction of the Engineer-in-Charge. Note : (i) Spare parts shall be measured and paid separately under respective items of BOQ here-in-after. (ii) Bidders are advised to visit AGE E/M office to get details of Pump's Make, description and capacity thereto before quoting their tenders.

Supply only Upper & lower rubber housing bush of 20 to25 HP, three phase, 415 Volts, 50 Hz, AC, submersible pump, all as specified and directed.

All as per item 24.02 here-in-before but stainless steel rotor sleeve.

All as per item 24.02 here-in-before but thrust bearing complete set.

Machining, grinding, balacing and reconditioning work for the rotor, stator items & capacities of 10 to 25HP submersible motors of any description including replacement of defective parts with new parts as required, complete all as specified and directed. Note: (i) Bidders are advised to visit AGE E/M office to get details of Pump's Make, description and capacity there to before quoting their tenders. (ii) Spare parts shall be measured and paid separately under respective items of BOQ here-in-after.

Supply only gun metal neck ring for multistage submersible pump of any description, 10 to 25HP capacity, all as specified and directed

All as per item 25.02 here-in-before but gun metal impeller.

All as per item 25.02 here-in-before but gun metal body bush.

All as per item 25.02 here-in-before but stainless steel distance bush (Spacer).

All as per item 25.02 here-in-before but pump Key.

Taking out & removing old burnt out windings of 10 to 25 HP, three phase, 415 Volts, 50 Hz, AC submersible electric motors of following capacity and rewinding of submersible electric motors with existing size PVC insulated, copper conductor as approved by the engineer-in-charge including cleaning the slots with carbon- tetra-chloride solution before rewinding ,transportation to site, fixing / lowering in position & testing on full load etc., complete all as specified and directed.

Lowering down of the submersible pump set after repair of any description and any capacity & in any position, in bore well along with column pipe and submersible cable of any size (approximately 40 mtr depth of pump set from GL) complete all as specified and directed by Engineer-in-Charge including making necessary electric connections & testing the pump set after lowering. Note: 1. Contractor shall take proper precautions while lowering pump set in bore well so as to avoid any damage to column pipe and submersible cable. All necessary T&P and equipments required for lifting out pump set etc shall be arranged by the contractor at his own cost. 2. Rates quoted by the contractor for the above item includes the cost of assembling & connecting pump set to column pipes & assembling, jointing and fixing column pipes/pump sets/submersible cable and making necessary connections and including reconnecting water supply system. The required materials like column pipes/ /submersible cable/pump sets etc (new/old retrieved materials) shall be provided by the department to contractor for fixing and lowering in bore wells.

Dismantling /taking down of existing pump with connecting accessoiries and repair/replacemenwith plastic shaft and impeller ail as per existing make and model of unserviceable/worn out granular chlorination,high pressure, single head gear motored adjustable dosing pump having out put 0 to 5 ltrs per hour, adjustable high pressure upto 10kg/sqcm with and including level gauge, agitator 120 watt 900RPM, single mounted motor with plastic shaft and impeller, complete all as specefied and directed.

Dismantling the complete pump set of capacity 10 HP from foundation channel after disconnecting all inlet and outlet connections,carrying the same to workshop,dismantling of pump, cleaning throughly and taking down worn out parts such as Ball bearing, Impeller, rubber coupling bushes ,brass ring, studs, replacement of the same with new lath work of pump shaft, impeller if required. reassembling, commissioning and testing after fix on orignal site for smooth functioning up to the entire satisfaction, complete all as specefied and directed.

Dismantling the electric motor induction motor assembly of pump set of capacity 10 HP from the foundation after disconnecting the electric connection, carrying the same to workshop,dismantling of electric motor and taking down worn out windings of rotor field coils and excitor coils rewinding the startor, rotor and excitor gauge replacement of insulation material, heat varishing provision of connecting leads and terminal plates etc to make the electric motor fully serviceable, reassembling the motor shifting back to the installation assembling the same with engine making electric connections, testing and commissioning, complete all as specefied and directed.

S & F in repair 10 Sqmm, 3 Core, flat submersible Cable, PVC insulated, PVC sheathed with multi-stranded copper conductors, 1100 Volt grade, complete all as specified and directed.

All as per item 31.01 here-in-before but 16 Sqmm 3 Core.

S&F in repair fully automatic star delta starter suitable for 30 HP, 415 volt, 50 HZ AC supply electric motor contactor size 32, over load relay 28-42 Amp, complete all as specified and directed.

S&F in repair fully automatic star delta starter suitable for 25 HP, 415 volt, 50 HZ AC supply electric motor contactor size 32, over load relay 28-36 Amp , complete all as specified and directed.

M&L lagging to 40mm dia GI pipes used in external water supply of plumbing all around with 25mm thick bonded mineral wool preformed SNAPON pipe section of density 144 Kg/Cum conforming to IS-9842 or equivalent and provided chicken wire mesh netting 25gauge 20mm meshing and plaster of Peris 3 to 5 mm thick all around the mesh after breaking old unsv/ broken lagging, complete all as specefied and directed

All as per item 34.01 here-in-before but 25mm dia.

All as per item 34.01 here-in-before but 20mm dia.

All as per item 34.01 here-in-before but 15 mm dia.

Supply and fixing in repair of 50mm dia GI union,complete all as specified and directed.

All as per item 35.01 here-in-before but 40mm dia.

All as per item 35.01 here-in-before but 25mm dia.

All as per item 35.01 here-in-before but 20mm dia.

All as per item 35.01 here-in-before but 15 mm dia.

Supply and fixing in repair of 50mm dia GI elbow,complete all as specified and directed.

All as per item 36.01 here-in-before but 40mm dia.

All as per item 36.01 here-in-before but 25mm dia.

All as per item 36.01 here-in-before but 20mm dia.

All as per item 36.01 here-in-before but 15 mm dia.

Periodically maintenance of hot water plant capacity 100000Kcal/hr or 200000 Kcal/hr including checking serviceability of burner, control panels, pressure gauge, temperature gauge, thermostat or temperature controller device, connection of water and flue gas pipes, hot water and cold water pumps, cleaning and servicing of boiler including any other safety device including replacement of defective parts with new parts as required, complete all as specified and directed. Note: (i) Spare parts shall be measured and paid separately under respective items of BOQ here-in-after.

Supply only relay as per sample suitable for hot water Capacity 200000 Kcal/hr, complete all as specified and directed

Supply only power contactor as per sample suitable for hot water Capacity 200000 Kcal/hr, complete all as specified and directed.

Supply only oil pump as per sample suitable for hot water capacity 100000 Kcal/hr, complete all as specified and directed.

Supply & fixing in repair changeover switch of capacity 100 Amps, onload, FP, 415 volts in sheet metal enclosure complete all as specified and directed.

S&F in replacement of rotational moulded polythylene 10000 litres capacity water storage tank (cylindrical vertical with closed top), 3 layer hoisted and fixed in position, complete all as specified and directed

ms new dar water star

M/S AK ENTERPRISES

M/S Sheikh and Co